AVerMedia Technologies EB5416DVD DVD Player User Manual

AVerMedia®
AVerDiGi EB5416DVD Pro
User Manual
FCC NOTICE (Class A)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Federal Communications Commission Statement
NOTE- This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by tuning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/television technician for help.
Class A ITE
Class A ITE is a category of all other ITE which satisfies the class A ITE limits but not the class B ITE limits. Such
equipment should not be restricted in its sale but the following warning shall be included in the instructions for use:
Warning -This is a class A product. In a domestic environment this product may cause radio interference in which case
the user may be required to take adequate measures.
European Community Compliance Statement (Class A)
This product is herewith confirmed to comply with the requirements set out in the Council Directives on the
Approximation of the laws of the Member States relating to Electromagnetic Compatibility Directive
2004/108/EEC.
Warning - This is a Class A product. In a domestic environment this product may cause radio interference in which case
the user may be required to take adequate measures to correct this interference.
DISCLAIMER
No warranty or representation, either expressed or implied, is made with respect to the contents of this documentation, its
quality, performance, merchantability, or fitness for a particular purpose. Information presented in this documentation has
been carefully checked for reliability; however, no responsibility is assumed for inaccuracies. The information contained in
this documentation is subject to change without notice.
In no event will AVerMedia be liable for direct, indirect, special, incidental, or consequential damages arising out of the use
or inability to use this product or documentation, even if advised of the possibility of such damages.
TRADEMARKS
AVerMedia is registered trademarks of AVerMedia TECHNOLOGIES, Inc. IBM PC is a registered trademark of
International Business Machines Corporation. Macintosh is a registered trademark of Apple Computer, Inc. Microsoft is a
registered trademark and Windows is a trademark of Microsoft Corporation. All other products or corporate names
mentioned in this documentation are for identification and explanation purposes only, and may be trademarks or
registered trademarks of their respective owners.
COPYRIGHT
© 2008 by AVerMedia INFORMATION, Inc. All rights reserved. No part of this publication may be reproduced, transmitted,
transcribed, stored in a retrieval system, or translated into any language in any form by any means without the written
permission of AVerMedia INFORMATION, Inc.
The mark of Crossed-out wheeled bin indicates that this product must not be disposed of with your other
household waste. Instead, you need to dispose of the waste equipment by handing it over to a designated
collection point for the recycling of waste electrical and electronic equipment. For more information about
where to drop off your waste equipment for recycling, please contact your household waste disposal
service or the shop where you purchased the product.
Battery Safety Information
-
Store the batteries in a cool dry place.
Do not dispose of used batteries in domestic waste. Dispose of batteries at special collection points or return to
point of sale if applies.
Remove the batteries during long periods of non-use. Always remove exhausted batteries from the remote
control. Battery leakage and corrosion can damage this remote control, dispose of batteries safely.
Do not mix old and new batteries.
Do not mix different types of batteries: alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium).
Do not dispose of batteries in a fire. The batteries may explode or leak.
Never short circuit the battery terminals.
-
WARNING
TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE
CAUTION
IF THERE IS ANY DAMAGE, SHORTAGE OR INAPPROPRIATE ITEM IN THE
PACKAGE, PLEASE CONTACT WITH YOUR LOCAL DEALER. WARRANTY
VOID FOR ANY UNAUTHORIZED PRODUCT MODIFICATION
NOTICE
- INFORMATION IN THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT
NOTICE.
- THE INFORMATION CONTAINED HEREIN IS TO BE CONSIDERED FOR
REFERENCE ONLY.
Table of Contents
Chapter 1 Introduction............................................................................... 1
1.1
Package Content .................................................................................................. 1
1.2
Features and Specifications.................................................................................. 1
1.3
Front Panel ........................................................................................................... 2
1.4
1.5
Back Panel ........................................................................................................... 5
Setting Up the DVR Unit ....................................................................................... 6
1.5.1
Installing the Removable Hard Disk ................................................................. 6
1.5.2
Install Internal SATA Hard Disk......................................................................... 8
1.5.3
1.5.4
Connecting Devices ....................................................................................... 10
Sensor, Relay and RS485 pinhole allocation ................................................. 11
1.5.4.1 Sensor Pin Definition .................................................................................. 11
1.5.4.2 Relay Pin Definition .................................................................................... 11
1.5.4.3 RS485 Pin Definition................................................................................... 12
Chapter 2 Operating the EB5416DVD Pro .............................................. 13
2.1
Familiarizing the Remote Control Buttons .......................................................... 13
2.1.1
Using USB Backup Button ............................................................................. 15
2.1.2
Using AB Repeat Function ............................................................................. 16
2.1.3
Controlling PTZ Camera................................................................................. 17
2.1.3.1 To Enter the PTZ Mode............................................................................... 17
2.1.3.2 To Set Preset Position ................................................................................ 17
2.1.3.3 To Control PTZ Camera.............................................................................. 18
2.2
Using the DVR for the First Time ........................................................................ 18
2.2.1
2.3
2.4
Set up the System Date and Time.................................................................. 18
Surveillance Screen............................................................................................ 19
Playback the Video ............................................................................................. 21
Chapter 3 OSD Navigation Tree .............................................................. 23
3.1
Menu Function .................................................................................................... 24
Chapter 4 Using the USB Playback Console ......................................... 43
4.1
4.2
Recommended system requirements ................................................................. 43
Installing the USB Playback Console.................................................................. 43
4.3
Running the USB Playback Console .................................................................. 44
4.3.1
To Cut and Save the Portion of the Recorded Video ...................................... 46
4.3.2
Playback DVR Recorded File from Hard Disk ................................................ 46
4.3.3
4.3.4
Playback Backup File(*.dvr) ........................................................................... 47
Playback Backup File (*.avf) .......................................................................... 47
Chapter 5 Backup Recorded Video File.................................................. 48
5.1
Recommended system requirements ................................................................. 48
5.2
Familiarizing with HDD Backup Application ........................................................ 48
5.3
To Backup Recorded Video File.......................................................................... 49
Chapter 6 ImageVerification .................................................................... 51
6.1
To Run the ImageVerification.............................................................................. 51
Chapter 7 iEnhance.................................................................................. 52
7.1
To Use iStable..................................................................................................... 53
Chapter 8 Using the Remote Programs.................................................. 54
8.1
Familiarizing the Web Viewer Buttons ................................................................ 55
8.1.1 To Setup Remote System Setting .................................................................. 57
8.1.1.1 System Setup ............................................................................................. 57
8.1.1.2 Camera Setup ............................................................................................ 59
8.1.1.3 Record Setup.............................................................................................. 60
8.1.1.4 Alarm/Sensor Setup.................................................................................... 61
8.1.1.5 Network Setup ............................................................................................ 63
8.1.1.6 User Setting................................................................................................ 65
8.2
Familiarizing the Remote Console Buttons......................................................... 66
8.2.1 To Setup Remote Console Setting ................................................................. 67
8.3
Familiarizing the WebViewer PTZ Buttons.......................................................... 68
8.4
Using the Remote Playback ............................................................................... 68
8.4.1
Familiarizing the Local Playback Buttons ....................................................... 70
8.4.1.1 To Cut and Save the Wanted Portion of the Recorded Video ..................... 71
8.4.2
Familiarizing the Download and Playback Buttons......................................... 72
Chapter 1
1.1
Introduction
Package Content
REC
ORD
STO
P
BAC
▲
▲
A-B
P LAY
A- B
▲
M+
FOC
FOC
FF
US+
▲
▲
ZOO
M_
ME
K UP
PAU
SE
REW
ZOO
SP EED
US _
SPE
P TZ
+
ED _
NU
PRE
SET
AUT
O SCA
ENT
N
ER
FN
AVe
A
rDiG VerMed
®
i EB
541 ia
Qui
6DV
ck In
DP
stal
ro
latio
nG
uide
˙
˙
˙
ID
1
2
3
5
4
6
7
9
8
10
11
13
12
14
15
16
(1)
RM-A
J2
(2)
(3)
(4)
(6)
(5)
(7)
(9)
(8)
(1) EB5416DVD Pro unit
(2) Remote Control (batteries included)
(3) Quick Installation Guide
(4) Power Cord
* The power cord varies depending on the standard power outlet of the country where it is sold.
(5) Audio cable
(6) Software CD (User Manual included)
(7) Extended IR Sensor cable
(8) Internal HDD holder
(9) 4 * screws for internal HDD installation
1.2
Features and Specifications
16CH composite video input and 16CH loop output
1CH Analog Spot monitor
16CH Audio In and 2CH Audio Out
Video compression: MPEG4
Multi-Quad for display and playback simultaneously
Hot-key on remote controller for auto save setting
Full function mouse control from front panel USB port
Copy camera setting to other channels
Camera name setting (up to 12 English letters)
Status bar and camera name on/off
16CH Sensor in and 4CH Relay out
Pre-recording function
1
1.3
3 level password authentication mechanism
DVD backup (up to 4.2GB)
Support 2 HDD backup (up to 1.5TB)
JavaViewer on mobile phone and PDAViewer supported
Built-in player to playback video without installing CD on PC
Remote playback and backup
Jog/Shuttle for playback
On Screen Display(OSD) control menu
Support network time synchronize function (Auto correction time delay & Day light saving)
Support WebViewer on Internet Explorer
Support Central Management System(CMS)
Support remote console
Support USB backup to pen drive and external hard disk
Support network, playback, and recording simultaneously
Supports 1 hard disk drive (not included)
Full-screen resolution:
Display: 720 x 480 (NTSC) / 720 x 576 (PAL)
Recording: 720 x 480 (NTSC) / 720 x 576 (PAL)
Dual VGA and TV display resolution:
VGA: 800 x 600 / 1024 x 768 / 1280 x 960 / 1280 x 1024
VGA: 3D de-interlaced engine for best VGA quality
Recording frame rate:
D1 mode: 60fps (NTSC) / 50fps (PAL)
CIF mode: 120 fps (NTSC) / 100fps (PAL)
Scheduled recording (00:00~23:00 set by hour and week )
Search for recorded video files by date/time/event
Support daylight saving and network time synchronize
Multiple language operation screens
Front Panel
Name
Function
(1) Power
ON/OFF DVR unit
(2) IR Sensor
Receive signal from the remote control to operate the DVR unit
2
Name
Function
(3) USB 2.0 port
2 x USB 2.0 ports for connecting any USB devices, ex: USB pen drive, external
hard disk, keyboard, mouse…and so on.
i
Do Not plug in two USB storage devices at the same time.
(4) Removable Hard
Disk Draw
i
To install hard disk for storage recorded video file
For hard disk spec, please referring to http://www.avermedia.com/nvd/hardware-recom_eb_c.asp
(5) Removable Hard
Disk Power
Removable hard disk power switch
To zoom in view of PTZ camera lens
(6) Zoom + / Zoom -
To zoom out view of PTZ camera lens
To focus in PTZ camera lens
(7) Focus + / Focus -
To focus out PTZ camera lens
To speed up movement of PTZ camera lens
(8) Speed + / Speed -
To speed down movement of PTZ camera lens
To save the preset position of PTZ camera. Adjust the PTZ camera
lens to the position that user wants, and then press
+
number button (1~9) to save the preset position. (see also Chapter
2.1.3.2)
When the PTZ camera in PTZ mode, press preset position number
button to move the PTZ camera to preset position.
(9) PTZ Save
i
Without setup preset position, the preset button (
functional when user presses.
(10) PTZ
) will not be
+ number button to switch to the certain PTZ camera view
Playback control button in playback mode
REV
FWD
:
:
(11) Playback button
Speed shuttle for adjusting reversed and forward (2x, 4x, 8x or
16x) speed during playback. Turn left is reversed and turn
right is forwarded.
To move to next or previous frame during playback. Turning
left is to go back to one previous frame and turning right is to
go forward one frame..
: To reverse at speed of 2x, 4x, 8x, or 16x
: To temporary stop playback or play the recorded video
: To fast forward at speed of 2x, 4x, 8x or 16x
: To stop playback
: To start recording
3
Name
Function
-
(12) Number button
-
~
-
(13) LCD Display
As a number key for entering password in
playback and preview mode
Channel camera selection number in
playback
and preview mode
As a preset position with
in PTZ control
mode
With
button can switch to different
screen display modes
Display DVR system status such as temperature and operate status
A functional key for multiple system control
-
Press
to enable multiple function modes and the
button will light up blue.
-
(14)
To exit multiple function modes, press
again.
+
: Switch to single screen display mode
+
: Switch to QUAD display mode
+
: Switch to 9 spilt screen display mode
+
: Switch to 16 spilt screen display mode
+
~
: User defined display mode(see also
MULTI-QUAD:LIVE and MULTI-QUAD:Play in Chapter 3)
system status indicators:
: System power indicator. Indicate running state of system. Lights when the
system is running.
: Removable hard disk indicator. Indicate running state of the hard disk.
(15) Status LEDs
Lights when the HDD is running
: Recording status indicator. Lights when the system is recording.
: Network status indicator. Lights when the system network connection is
enabled.
-
In OSD mode: Move selection to left, right, up, and down
In PTZ mode: To move PTZ camera lens to left, right, up and down
(16)
Confirm or make a selection
(17)
To call out OSD menu
(18)
To start auto scan
(19)
To start USB backup
(20)
(21) DVR-ROM
AB Repeat function allow user to set a video segment from A to B point and play
on the surveillance screen until user stop. User also can backup AB Repeat file
to pen drive or external hard disk (see also 2.1.1).
To backup the recorded file to DVD+RW disk
4
1.4
Back Panel
Name
Function
(1)
Video Loop Out
Output the video signal to a CCTV monitor. Only output one channel signal at a
time.
(2)
CH1~ 16
Input the video camera signal and display it on channel 1~ 16
(3)
Spot Monitor
Output a video signal to a Spot Monitor when an alarm event is coming
(4)
LAN Port
For Ethernet connection
(5)
TV Out
Output the video signal to a TV
(6)
VGA Out
Output the video signal to a CRT or LCD monitor
(7)
Audio I/O
Support 16 channels audio input (ex. Microphone) and 2 channels of audio
output(ex. Speaker)
i
The audio input device needs to be powered by external power.
(8)
RS485
For PTZ camera connection (also see 1.5.3)
(9)
Sensor In
Support up to 16 sensor devices
(10) Alarm Out
Support 4 relay devices (Relay: 1A @ 125V AC/30V DC)
(11) Power Plug
Connect the power cord into this port
5
1.5
Setting Up the DVR Unit
1.5.1 Installing the Removable Hard Disk
The DVR unit allows user to install one hard disk. Before installing the hard disk, make sure to set
the hard disk master jumper setting. Adjust the jumper setting according to the instructions on the
hard disk label.
i
For hard disk spec, please referring to http://www.avermedia.com/nvd/hardware-recom_eb.asp
The “compatible hard disks” indicated in the above recommendation list only means that these
commercially available hard disks were tested with AVerMedia® products and functioned well
under normal operation conditions. AVerMedia® does not guarantee or provide warranties,
explicitly, implied or statutory with respect to the reliability of the hard disk function or its
compatibility. In no event AVerMedia® shall be liable for damages, with respect to any business
interruption of clients, lost profits, loss of programs or other data on your information handling
system or otherwise. This includes direct, indirect, incidental, special, or consequential
damages, resulting from the incompatibility caused by the usage of these hard disks, even if
AVerMedia® has expressly advised about the risk of such damages. The entire risk arising out of
the use of any information attached here with is borne by the recipient.
Follow the illustrated instructions below to install the hard disk:
1.
Unlock the removable hard disk drawer
2.
Open the removable hard disk drawer
3.
And then, pull out the removable hard disk
drawer
4.
Remove the removable hard disk drawer cover
6
5.
Carefully insert the hard disk in the removable
rack
7.
And then, close the removable hard disk drawer 8.
cover
9.
Lock the removable hard disk drawer keylock
6.
Turn the removable hard disk drawer over and
screw hard disk with screws
Slide the drawer back
10. Power on the removable hard disk drawer
11. You may now connect all the cables. When the power is connected, the Power LED light
7
turns on
1.5.2 Install Internal SATA Hard Disk
User can install one SATA hard disk inside the DVR unit if it is necessary. Please follow the below
steps to install the hard disk.
1. Loosen all screws
2. Push the cover backward and lift
3. Loosen the screws of holder that will make
installation more convenient
4. Secure the brackets on the hard disk both side
5. Plug the SATA cable into hard disk
6. Plug the power cable into hard disk
8
7. Secure the hard disk inside the unit
8. Screw tight the holder
9. Push the cover forward
10. Secure the cover
9
1.5.3 Connecting Devices
The back panel of the DVR unit, user can connect up to 16 video cameras, 16 sensor devices, 4
alarm devices, PTZ camera and output video to a TV or CRT/LCD monitor. Connecting the unit to a
pen drive or external hard disk through USB connection for backup, then use the bundled software
enables user to transfer, playback and segment the video. Follow the illustration below to make the
connection:
Each time you change the video display output, the power must be turned off and on to reset the
DVR unit.
i
- All connected devices need to be powered by external power.
- Do Not plug in two USB storage devices at the same time.
10
1.5.4 Sensor, Relay and RS485 pinhole allocation
The Sensor, Alarm, and PTZ camera ports enable you to connect 16 sensor inputs, 4 relay outputs,
and 1 PTZ camera. Just connect the external sensor, relay, and PTZ camera pin directly to the
pinhole. Check the table below and locate which pinhole is assigned to sensor input and relay
output.
1.5.4.1
Sensor Pin Definition
Sensor Pin #
1.5.4.2
Definition
Sensor Pin #
Definition
1
Sensor 1 signal
9
Sensor 9 signal
G
Sensor 1 ground
G
Sensor 9 ground
2
Sensor 2 signal
10
Sensor 10 signal
G
Sensor 2 ground
G
Sensor 10 ground
3
Sensor 3 signal
11
Sensor 11 signal
G
Sensor 3 ground
G
Sensor 11 ground
4
Sensor 4 signal
12
Sensor 12 signal
G
Sensor 4 ground
G
Sensor 12 ground
5
Sensor 5 signal
13
Sensor 13 signal
G
Sensor 5 ground
G
Sensor 13 ground
6
Sensor 6 signal
14
Sensor 14 signal
G
Sensor 6 ground
G
Sensor 14 ground
7
Sensor 7 signal
15
Sensor 15 signal
G
Sensor 7 ground
G
Sensor 15 ground
8
Sensor 8 signal
16
Sensor 16 signal
G
Sensor 8 ground
G
Sensor 16 ground
Relay Pin Definition
Pin #
Definition
1
Relay signal
2
Relay signal
3
Relay signal
4
Relay signal
11
1.5.4.3
RS485 Pin Definition
When connect PTZ camera through RS485 interface, please refer to the following pin
definition to connect the DVD and PTZ.
Pin #
DVR
PTZ
TX+
RS485 TX+ signal
RS485 RX+ signal
TX-
RS485 TX- signal
RS485 RX- signal
RX+
RS485 RX+ signal
RS485 TX+ signal
RX-
RS485 RX- signal
RS485 TX- signal
12
Chapter 2
2.1
Operating the EB5416DVD Pro
Familiarizing the Remote Control Buttons
Use the Remote control to operate the OSD menu on surveillance screen.
(4)
RECORD
BACK UP
(2)
(1)
STOP
PAUSE
REW
PLAY
A-B
(3)
A-B
▲
▲
ZOOM
▲
▲
FOCUS+
ZOOM+
(9)
_
FOCUS
SPEED
_
(10)
(11)
PRESET
MENU
AUTOSCAN
(13)
(15)
(17)
ENTER
(16)
(18)
(7)
(8)
SPEED+
_
PTZ
(12)
(14)
(5)
FF
▲
(6)
FN
ID
(19)
˙
˙
˙
1
(20)
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
RM-AJ2
Name
Function
To start recording video
(2)
USB backup(see 2.1.1)
(3)
Stop playing / Stop recording
(4)
To pause playing
(6)
(7)
(9)
Set a playing recorded video from A point to B point segment and repeat
playing on surveillance screen(See 2.1.2)
Decrease the video playback at the speed of 2x, 4x, 8x, or 16x
Fast play the video playback at the speed of 2x, 4x, 8x, or 16x
▲
(8)
A-B
▲
▲
(5)
▲
▲
(1)
To play the video
To zoom in view of PTZ camera
To zoom out view of PTZ camera
(10)
To speed up movement of PTZ camera lens
To speed down movement of PTZ camera lens
(11)
To focus in PTZ camera lens
To focus out PTZ camera lens
(12)
To enter PTZ mode
13
Name
(13)
Function
To save the preset position of PTZ camera. Adjust the PTZ camera lens to
the position that user wants, and then press
~
+ number button (
) to save the preset position. (see also Chapter 2.1.3.2)
When the PTZ camera in PTZ mode, press preset position number button
to move the PTZ camera to preset position.
(14)
To enter the OSD Main menu / Exit from the main menu or sub-menu
display
(15)
To enable the auto scan function
(16)
Confirm or make a selection
To move the selection to the left
To move PTZ camera to left
(17)
To move the selection to the right
To move PTZ camera to right
To go up and select the items in the menu list or change the
settings
To move PTZ camera to up
To go down and select the items in the menu list or change
the settings
To move PTZ camera to down
(18)
A functional key for multiple system control
-
Press
to enable multiple function modes and the
button
will turn to blue light.
-
To exit multiple function modes, press
again.
+
: Switch to single screen display mode
+
: Switch to QUAD display mode
+
: Switch to 9 spilt screen display mode
+
: Switch to 16 spilt screen display mode
+
5
~
16
: Screen display mode can be defined by user
(see also Multi-Quad : Live & Mutli-Quad:play in Chapter 3)
+
: Switch the different on screen information display
(channel name, date, time, hard disk usage). There 4 type of on screen
information display:
Display all (channel name, date, time hard disk, hard disk usage)
No channel name display
Display channel name only
None
14
Name
(19)
Function
To enter the DVR ID number that assigned by user for multiple DVR
controlling ( see also Multiple DVR & DVR ID in Chapter 3)
ID
Press
1
2
3
4
1
ID
can unselect all DVR
+
~
- Channel camera selection number in playback and preview mode
5
6
7
8
9
10
11
12
13
14
15
16
(20)
- As preset positions that work with
- With
in PTZ control mode
button can switch to different screen display modes)
2.1.1 Using USB Backup Button
User can press
button to backup the AB Repeat video file.
1. Set the AB Repeat file (see 2.1.2).
2. Plug in pen drive, external hard disk to DVR system or place DVD+RW disk into DVD-ROM
button.
3. During the AB Repeat playback, press
4. Select the backup mode – USB or DVD+RW
BACK U P SETTING
BACKUP SELECT
5. And then, press
USB
to start backup file. To cancel backup, press
backup mode.
BACKUP PROCESSING
15%
820M
AVAILABLE SIZE
6. When backup process is done, press any key to exit the backup mode.
USB BACKUP SUCCESSFUL
PRESS ANY KEY TO EXIT
15
to exit
i
The external hard disk needs to be powered by external power.
2.1.2 Using AB Repeat Function
AB Repeat function allow user to set a video segment from A to B point and play on the surveillance
screen until user stop. User also can backup AB Repeat file to pen drive or external hard disk (See
2.1.1).
(play button) to call out the PLAYBACK menu to find the recorded video that user
1. Press
wants to playback.
2. Select TIME SEARCH or EVENT LIST.
- TIME SEARCH (search by date and time): select the date and time from where you want to
begin the video playback.
- EVENT LIST (search by condition): select from the list.
3. During the playback, press A-B to set the A point of video segment. And then, press A-B
again to set the B point of video segment. On the surveillance screen will display “A-B” and
repeat playing the AB point video segment which user has set. To cancel AB repeat, press
A-B again.
16
2.1.3 Controlling PTZ Camera
Using remote control, user can easily control PTZ camera at local site. Before starting, please go to
OSD menu to enable PTZ control (see 3.1 Menu Function: PTZ Setup).
2.1.3.1
To Enter the PTZ Mode
To control PTZ camera, user need to enter the PTZ mode first. Press
channel number button ( 1
~
button, and camera
) that the selected channel will switch to PTZ mode in a full
screen display.
To exit PTZ mode, press
. Also, the system will automatically exit PTZ mode when the idle
time is over 1 minute.
2.1.3.2
To Set Preset Position
User can set 16 preset positions for PTZ camera. Using
+ 1
to
button to set the
preset position.
and camera channel number button ( 1
1. Press
2. Using
,
,
and
~
) to enter PTZ mode.
to adjust the PTZ camera to the position that user
wants.
3. Press
to save
4. To move the PTZ camera to preset position, just press the number button.
17
2.1.3.3
To Control PTZ Camera
To move, adjust focus, and zoom in/out camera lens can be done by using some function buttons
on the remote control.
To move the PTZ camera lens to the right
To move the PTZ camera lens to the left
To move the PTZ camera lens to go up
To move the PTZ camera lens to go down
To zoom in PTZ camera
To zoom out PTZ camera
To speed up movement of PTZ camera lens
To speed down movement of PTZ camera lens
To focus in PTZ camera lens
To focus out PTZ camera lens
2.2
Using the DVR for the First Time
Upon connecting the power, the unit automatically detects the status of the hard disk. The hard disk
must be formatted before user can use it with EB5416DVD Pro. If you are prompt to format the hard
disk, press
(select) for YES to format the hard disk and
(menu) for NO to remain
unchanged.
HARD DISK INFORMATION
HDD1 FORMAT INVALID
HDD 1 SIZE
953,669 MB
HDD 1 FORMAT ?
HDD2 NOT FOUND
HDD2 SIZE
YES (
/
0 MB
), NO (MENU/
)
2.2.1 Set up the System Date and Time
Before starting record video, adjust the date and time first.
1. Press
to call up the OSD menu and then use
and
to go up and down and select
or
SYSTEM. And then, press
to confirm the
TIME SETUP
DATE FORMAT
DATE
TIME
AUTO SYNC TIME
TIME ZONE
LAST SYNC TIME
YYYY/MM/DD
2008 / 03 / 12 WED
21 : 07 : 45
OFF
GMT
2008 / 01 / 01
00 : 00 : 00
DAYLIGHT SAVING
selection.
2. In SYSTEM, use
and
to go up and
down and select the TIME SETUP and press
make a selection. And then, use
and
18
to
to select the DATE FORMAT and
press
or
to confirm the selection.
3. To select the format of date, Press
or
or
to change the date format. Press
the date. Press
or
or
and
buttons
to confirm the selection.
and
4. After selected the date format, use
DATE and press
and use
to confirm.
Use
to go up and down and select the
and
buttons to adjust
to confirm the selection.
5. To adjust TIME, follow the above step 3 or 4.
6. Press
2.3
to go back to main menu.
Surveillance Screen
To know if the channel is being recorded, the “” record symbol would appear beside the channel
number. The
(microphone) and
(speaker) indicate that the audio is available. The
(motion
record) indicate that the channel is in motion record mode. The information below the screen shows
the current date and time, hard disk drive, and the percentage of the used hard disk space.
Preview Mode
In full screen preview, press
+ 1
~
can switch to different screen display mode.
19
In Playback mode, the
(AB Repeat) indicate that playback is in AB repeat status. The
indicate that DVR unit is playback recorded video.
(Play)
Playback Mode
The EB5416DVD Pro supports mouse control that user can use mouse (the middle button of
mouse) to click channel to switch between preview and playback mode. To switch back, click
channel with middle button of mouse again. Click right mouse button on screen to call out the OSD
menu. Use the roller button to select items (user can use left mouse button to click the selection,
too) and change selection in OSD menu. To confirm the selection in OSD menu, click left mouse
button. To exit current screen, click right mouse button.
Preview and Playback Simultaneously
20
2.4
Playback the Video
The DVR system can record and playback video simultaneously. Therefore, user doesn’t need to
stop recording while playback the video.
1.
Press
2.
Use
and
buttons to go up and
PLAYBACK
T IME S E A R C H
E V E NT L IS T
down and select TIME SEARCH or EVENT LIST. Then,
or
press
to make a selection.
TIME SEARCH (search by date and time):
1.
and
Use
buttons and select
SEARCH TIME. Then press
2.
TIME SEARCH
HARD DISK :
or
again to
HDD 1
START TIME : 2008 / 03 / 04
END TIME
: 2008 / 03 / 05
10 : 00 : 01
13 : 08 : 13
SEARCH TIME : 2008 / 03 / 04
START SEARCH
10 : 00 : 01
make the selection.
In the SEARCH TIME, user may now select the date
and time from where you want to begin the video
playback.
Use
and
buttons to move the selection to the left and right. Use
buttons to select the date and time. Then press
or
and
again to make the
selection.
3.
To start video playback, the time in second must be set. Use the
to the right most. Use
or
and
buttons and select the time in second. Then press
.
EVENT LIST (search by event):
1.
buttons to move the selection
HARD DISK SELECT
Select hard disk drive (HDD1 or HDD2). Use
and
buttons to select it.
HARD DISK SELECT HDD 1
21
2.
Use
and
the list. Press
buttons to select from
or
selection. User
again to make the
and
to go next
page or back to previous page.
EVENT LIST
2008 / 03 / 03
2008 / 03 / 03
2008 / 03 / 03
2008 / 03 / 03
2008 / 03 / 03
2008 / 03 / 03
2008 / 03 / 03
2008 / 03 / 03
2008 / 03 / 03
13
13
12
11
11
11
11
11
11
: 26
: 00
: 00
: 48
: 30
: 29
: 28
: 28
: 25
: 34
: 01
: 01
: 37
: 23
: 47
: 55
: 33
: 41
13 : 26 : 50
13 : 16 : 46
13 : 00 : 01
12 : 00 : 00
11 : 31 : 18
11 : 30 : 13
11 : 28 : 58
11 : 28 : 55
11 : 28 : 32
A
B
M
M
M
M
M
M
M
: MOTION RECORDING
: SENSOR RECORDING
3.
Listed below are the following recording conditions:
A – Always Recording
It records non-stop and automatically continue recording when interrupted
S – Sensor Recording
It records when the sensor has been triggered
M – Motion Recording
It records when any movement has been detected
B – Button Recording
It records when the
4.
record button is pressed
The “” play symbol would appear beside the channel number when you are previewing in playback
mode.
i
To playback the recording files during the daylight saving period; please select Event List to find
the event that user wants to playback. On the first day and last day of daylight saving only has on
record in Time search, so user can’t find the specific playback file in time search.
22
Chapter 3
OSD Navigation Tree
The follow figure is an OSD menu tree map. To call out the OSD menu, press
control.
23
on the remote
3.1
Menu Function
If the unit is currently recording the video, user may have to stop video recording to change the
settings. User can use the following way to setup DVR unit.
Remote Controller
USB Mouse
Front Panel control buttons
and
to go up and down the selection list or
For using remote controller, use
change the value of selection. Use
item. Use
or
and
to move to left and right in the selection list or
to make a confirmation. Press
to go back previous page or exit from
current page.
For using mouse, use right mouse button to call up OSD menu and use left mouse button to make
selection. Use middle button (roller) of mouse to change the value of selection or go back to
previous page.
**The red frame turns yellow when you are making a selection.
OSD MENU
MAIN MENU
CAMERA
RECORD
HARD DRIVE
SENSOR / ALARM
MOTION
NETWORK
BACKUP
SYSTEM
Description
CAMERA
Select the channel number to display and record the video on the
surveillance screen, and enable/disable audio recording. Also,
setup cameras name, video shield, PTZ camera, auto scan,
audio output and adjust video.
CAMERA SETUP
CAMERA SELECT
RECORD SELECT
AUDIO RECORD
CAMERA TITLE
VIDEO SHIELD
VIDEO ADJUSTMENT
PTZ CONTROL
AUTO SCAN
AUDIO OUT
1
9
1
9
1
9
2
10
2
10
2
10
3
11
3
11
3
11
4
12
4
12
4
12
5
13
5
13
5
13
6
14
6
14
6
14
7
15
7
15
7
15
8
16
8
16
8
16
1
9
2 3 4 5
10 11 12 13
6
14
7 8
15 16
CAMERA SELECT
Select the channel to display the video on the surveillance
screen.
RECORD SELECT
Enable/disable the channel number to record video
i
The channels which could be recorded should be
enabled in the CAMERA SELECT first.
AUDIO RECORD
Enable/disable audio recording. To record sound, make sure the
audio input device (ex: microphone) is connected to the DVR
unit.
24
OSD MENU
CAMERA SETUP
CAMERA SELECT
RECORD SELECT
AUDIO RECORD
CAMERA TITLE
VIDEO SHIELD
VIDEO ADJUSTMENT
PTZ CONTROL
AUTO SCAN
AUDIO OUT
Description
1
9
1
9
1
9
2
10
2
10
2
10
3
11
3
11
3
11
4
12
4
12
4
12
5
13
5
13
5
13
6
14
6
14
6
14
7
15
7
15
7
15
8
16
8
16
8
16
CAMERA TITLE
To assign a name for each channel. The maximum inputs is 12
characters that includes letters of the alphabet, numbers, +, -, @,
/, space, dash, and dot.
CAMERA TITLE SETUP
1
9
2 3 4 5
10 11 12 13
6
14
7 8
15 16
CAMERA
CAMERA
CAMERA
CAMERA
CAMERA
CAMERA
CAMERA
CAMERA
CAMERA
CAMERA
CAMERA
CAMERA
CAMERA
CAMERA
CAMERA
CAMERA
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
CH
CH
CH
CH
CH
CH
CH
CH
CH
CH
CH
CH
CH
CH
CH
CH
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
VIDEO SHIELD
Select an area that will be blocking for particular security issue
when DVR unit is recording such as enter password for entrance
guard.
Use the
,
,
, and
the left, right, up, and down. Use the
block area
25
buttons to move to
buttons to select the
OSD MENU
CAMERA SETUP
CAMERA SELECT
RECORD SELECT
AUDIO RECORD
CAMERA TITLE
VIDEO SHIELD
VIDEO ADJUSTMENT
PTZ CONTROL
AUTO SCAN
AUDIO OUT
CAMERA SETUP
CAMERA SELECT
RECORD SELECT
AUDIO RECORD
CAMERA TITLE
VIDEO SHIELD
VIDEO ADJUSTMENT
PTZ CONTROL
AUTO SCAN
AUDIO OUT
Description
1
9
1
9
1
9
2
10
2
10
2
10
5
13
5
13
5
13
6
14
6
14
6
14
7
15
7
15
7
15
1
9
2 3 4 5
10 11 12 13
6
14
7 8
15 16
1
9
1
9
1
9
1
9
2
10
2
10
2
10
3
11
3
11
3
11
3
11
3
11
3
11
4
12
4
12
4
12
4
12
4
12
4
12
5
13
5
13
5
13
2 3 4 5
10 11 12 13
6
14
6
14
6
14
6
14
7
15
7
15
7
15
8
16
8
16
8
16
8
16
8
16
8
16
7 8
15 16
VIDEO ADJUSTMENT :
Select the camera number and set to adjust the video brightness,
contrast, hue, and saturation value.
To reset the setting, select RESET TO DEFAULT VALUE. The
video adjustment setting can be copy to reset of cameras by
selecting COPY SETTING VALUE TO camera #.
VIDEO ADJUSTMEN SETUP
1
CAMERA
128
BRIGHTNESS
128
CONTRAST
128
HUE
SATURATION
128
RESET TO DEFAULT VALUE
COPY SETTING VALUE TO
2
PTZ SETUP
To enable PTZ camera control by remote control and setup PTZ
camera parameters.
PTZ SETUP
CAMERA
PTZ CONTROL
ID
PROTOCOL
BAUD RATE
AUTO PAN GROUP
DWELL TIME
1
OFF
1
PELCO-D
2400
1-4 5-8
05 SEC
9 - 12 13 - 16
CAMERA:
Select the channel of PTZ camera. If the PTZ camera is
connecting on channel 1, then select the camera 1 for PTZ video
to be display on channel 1.
PTZ CONTROL:
To enable/disable PTZ camera can be controlled by remote
control at local site.
ID:
Assign an ID to PTZ camera. The ID range is from 001 to 255 but
is limiting by protocol of PTZ camera. Please refer to your PTZ
camera user’s manual for more detail of PTZ ID assignment.
i
We suggest assigning PTZ camera ID star from 5 to
avoid conflict with ID of camera channels.
PROTOCOL:
Select the protocol of PTZ camera. The protocol will be
differenced that depends on the brand of PTZ camera. The DVR
system currently supports 3 protocols ─ PELCO-D, PELCO-P,
and CANON VC-C4R. Please refer to your PTZ camera user
manual to make sure which protocol is using for.
26
OSD MENU
Description
PTZ SETUP
CAMERA
PTZ CONTROL
ID
PROTOCOL
BAUD RATE
AUTO PAN GROUP
DWELL TIME
BAUD RATE:
To setup the baud rate of PTZ camera. For more detail, please
refer to your PTZ camera’s user manual.
1
OFF
1
PELCO-D
2400
1-4 5-8
05 SEC
9 - 12 13 - 16
AUTO PAN GROUP:
Select the preset number to assign an auto move direction for
the PTZ camera. For example: 1-4 means the PTZ camera will
auto move from preset position 1, 2, 3 to 4.
DWELL TIME:
Set a time that how long the PTZ camera stays in that position
before it moves to the next one.
CAMERA SETUP
CAMERA SELECT
RECORD SELECT
AUDIO RECORD
CAMERA TITLE
VIDEO SHIELD
VIDEO ADJUSTMENT
PTZ CONTROL
AUTO SCAN
AUDIO OUT
1
9
1
9
1
9
1
9
2
10
2
10
2
10
3
11
3
11
3
11
4
12
4
12
4
12
5
13
5
13
5
13
2 3 4 5
10 11 12 13
6
14
6
14
6
14
6
14
7
15
7
15
7
15
8
16
8
16
8
16
7 8
15 16
AUTO SCAN
Enable/disable auto cycle switch to display the next channel
when in full screen preview. User can set different switch time for
each channel. The time range is from 1 ~30 seconds.
AUTO SCAN
AUTO SCAN
CHANNEL - 1
CHANNEL - 2
CHANNEL - 3
CHANNEL - 4
CHANNEL - 5
CHANNEL - 6
CHANNEL - 7
CHANNEL - 8
10 SEC
10 SEC
10 SEC
10 SEC
10 SEC
10 SEC
10 SEC
10 SEC
OFF
CHANNEL - 9
CHANNEL - 10
CHANNEL - 11
CHANNEL - 12
CHANNEL - 13
CHANNEL - 14
CHANNEL - 15
CHANNEL - 16
10 SEC
10 SEC
10 SEC
10 SEC
10 SEC
10 SEC
10 SEC
10 SEC
AUDIO OUT
Select the channel to output the audio signal. Please make sure
the audio output device (such as a speaker) is connected to DVR
unit. Use
,
and
27
,
buttons to move to the selection. Use
buttons to select the channel.
OSD MENU
MAIN MENU
CAMERA
RECORD
HARD DRIVE
SENSOR / ALARM
MOTION
NETWORK
BACKUP
SYSTEM
Description
RECORD
To setup the recording relate parameters.
RECORD SETUP
RECORD MODE
RECORD FRAMERATE
VIDEO QUALITY
RECORD SCHEDULE
D1
240
GOOD
RECORD MODE
Select D1/CIF recording mode.
Under D1 mode, the video recording is in full screen resolution
and takes turns from one channel to the next one when Auto
Scan enables. Each channel is recorded only at a maximum
frame rate of 15fps. User can switch to view the video in full
screen or QUAD screen.
Whereas in CIF mode, video recording is at a lower resolution,
but each video is recorded in 30fps/25fps (NTSC/PAL). User can
switch to view the video in full screen or QUAD screen.
RECORD FRAMERATE
Set the number of frames per second to be recorded. Refer to
the table below for the available record frame rate settings. The
higher the frame rate is, it uses more hard disk space
Video Standard
NTSC
PAL
D1
16, 80, 240
16, 80, 200
CIF
16, 80, 160, 240, 480
16, 80, 200, 400
Record Mode
VIDEO QUALITY :
Select the video quality setting from BEST, HIGH, MEDIUM,
GOOD, NORMAL or LOW.
BEST – best record quality but less record hours
LOW – longest record hour but quality is ordinary
NORMAL – allows you to record more hours but the quality
of the recorded video is moderate
28
OSD MENU
RECORD SETUP
RECORD MODE
RECORD FRAMERATE
VIDEO QUALITY
RECORD SCHEDULE
Description
D1
240
GOOD
RECORD
Use
SCHEDULE
,
,
buttons to move to left and right. Use
and
buttons to select the mode of record
schedule.
RECORD SCHEDULE SETUP
SUN
MON
TUE
WED
THU
FRI
SAT
: SENSOR RECORDING
: MOTION RECORDING
: NO RECORD
By default, in 24 hours, the recording schedule is set to always
record every hour. Refer to the table below to customize the
recoding condition
MAIN MENU
CAMERA
RECORD
HARD DRIVE
SENSOR / ALARM
MOTION
NETWORK
BACKUP
SYSTEM
Condition
Description
NO REC
Disable video recording
ALWAYS REC
Record non-stop
MOTION REC
Start recording when any movement is
detected
SENSOR REC
Start recording when the sensor has
triggered
HARD DRIVE SETUP
HARD DRIVE SETUP
OVERWRITE ENABLED YES
HDD1 SIZE
953,669 MB
HDD1 USED
1,936 MB
HDD1 FORMAT
HDD2 SIZE
0 MB
HDD2 USED
0 MB
HDD2 FORMAT
HDD 1/2 SIZE shows the total capacity of the hard disk.
HDD 1/2 USED shows the amount of space that has been
used.
OVERWRITE
ENABLED
Enable/disable overwriting the earliest record when the hard disk
space runs out. By default, the HDD overwrite setting is enabled
29
OSD MENU
HARD DRIVE SETUP
OVERWRITE ENABLED YES
HDD1 SIZE
953,669 MB
HDD1 USED
1,936 MB
HDD1 FORMAT
HDD2 SIZE
0 MB
HDD2 USED
0 MB
HDD2 FORMAT
Description
HDD 1/2 FORMAT
For security purpose, you may have to enter the password to
format hard disk
To format hard disk:
1. Use
and
buttons to go up and down
and select HDD 1/2 FORMAT. Then press
or
2. In the ADMINISTRATOR PASSWORD screen, press
. Then use
or
and
buttons to
select the security combination number. Repeat till you key
in the last number (The default admin password is 111111).
ADMINISTRATOR PASSWORD
CURRENT
CHECK
******
3. After entering the password, press
.
4. And then, select CHECK and a confirmation screen will
display. Press YES(ENTER) button to start formatting the
hard disk. To cancel the hard disk formatting, press
NO(MENU) button.
FORMAT HDD1 ?
YES (
/
), NO (MENU/
)
5. It is done when the “HDD FORMAT COMPLETED” appears
Formatting the hard disk will permanently delete all the
records and can no longer be retrieved
30
OSD MENU
Description
MAIN MENU
CAMERA
RECORD
HARD DRIVE
SENSOR / ALARM
MOTION
NETWORK
BACKUP
SYSTEM
SENSOR / ALARM
To setup sensor and alarm relate parameters.
SENSOR / ALARM SETUP
SENSOR
ALARM
SENSOR RECORD TIME 10 SEC
010 SEC
ALARM OUT TIME
SPOT MONITOR
SENSOR RECORD TIME
Set the amount of time (in second) to start record when the
sensor has triggered
ALARM OUT TIME
Set the amount of time (in second) to continue sending the alarm
once triggered
SENSOR SETUP
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
-
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
NOT
NOT
NOT
NOT
NOT
NOT
NOT
NOT
NOT
NOT
NOT
NOT
NOT
NOT
NOT
NOT
INSTALLED
INSTALLED
INSTALLED
INSTALLED
INSTALLED
INSTALLED
INSTALLED
INSTALLED
INSTALLED
INSTALLED
INSTALLED
INSTALLED
INSTALLED
INSTALLED
INSTALLED
INSTALLED
SENSOR / ALARM SETUP
SENSOR
ALARM
SENSOR RECORD TIME 10 SEC
ALARM OUT TIME
010 SEC
SPOT MONITOR
SENSOR SETUP
CHANNEL 1~16 :
Customize the initial state of the attached sensor. Refer to the
table below to customize the sensor state
Condition
Description
NOT
INSTALLED
Indicates that there is no sensor
connected
NORMAL
OPEN
Indicates that the initial state of the
sensor is normal open. Video recording
initiates when there is a changes in the
sensor state
NORMAL
CLOSE
Indicates that the initial state of the
sensor is normal close. Video recording
initiates when there is a changes in the
sensor state
ALARM SETUP
ALARM SETUP
ALARM OUT
BUZZER
1
9
1
9
VIDEO LOSS
1
9
HDD FAIL
ON
COPY SETTING VALUE TO
SENSOR
MOTION
2
10
2
10
2
10
3
11
3
11
3
11
4
12
4
12
4
12
5
13
5
13
5
13
6
14
6
14
6
14
7
15
7
15
7
15
8
16
8
16
8
16
BUZZER
ALARM OUT:
Select the way of alarming – BUZZER, RELAY-1, RELAY-2,
RELAY-3, RELAY-4, or ALL.
SENSOR:
Select the channel that will be send out the alarm when sensor
has been triggered
31
OSD MENU
ALARM SETUP
ALARM OUT
Description
1
9
1
9
VIDEO LOSS
1
9
HDD FAIL
ON
COPY SETTING VALUE TO
SENSOR
MOTION
MOTION:
BUZZER
2
10
2
10
2
10
3
11
3
11
3
11
4
12
4
12
4
12
BUZZER
5
13
5
13
5
13
6
14
6
14
6
14
7
15
7
15
7
15
8
16
8
16
8
16
Select the channel that will send out the alarm when motion has
been detected
VIDEO LOSS:
Select the channel that will send out the alarm when video is lost.
HDD FAIL:
Enable/disable send out alarm when hard disk is failed.
COPY SETTING VLAUE TO BUZZER:
Copying alarm out setting to selected device.
SENSOR / ALARM SETUP
SENSOR
ALARM
SENSOR RECORD TIME 10 SEC
010 SEC
ALARM OUT TIME
SPOT MONITOR
SPOT MONITOR
Enable/disable to display channel alarm event in full screen
mode when the sensor is activated or motion is detected. When
there are multiple alarm events, DVR system will display the last
alarm event.
SPOT MONITOR SETUP
SENSOR
MOTION
CAMERA
SPOT MONITOR TIME
1
9
1
9
2
10
2
10
3
11
3
11
1
10 SEC
4
12
4
12
5
13
5
13
6
14
6
14
7
15
7
15
8
16
8
16
SENSOR:
Select the channel that will sent out the alarm event for display
when the sensor has been triggered.
MOTION:
Select the channel that will sent out the alarm event for display
when the motion has been detected.
CAMERA:
Select the channel to display alarm event.
SPOT MONITOR TIME:
Set a period time (0 ~ 255 sec) for alarm event to display on
surveillance screen.
32
OSD MENU
MAIN MENU
CAMERA
RECORD
HARD DRIVE
SENSOR / ALARM
MOTION
NETWORK
BACKUP
SYSTEM
Description
MOTION SETUP
MOTION SETUP
SENSITIVITIY
MOTION RECORD TIME
MOTION CAMERA 1 2
9 10
MASK MOTION
L
010 SEC
3
4 5
11 12 13
6
14
7
15
8
16
SENSITIVITY:
Set the sensitivity level. The sensitivity is from HI (High), 9~ 2
and LO (Low).
MOTION
RECORD
TIME:
Set the amount of time (in second) to record when motion is
detected.
MOTION CAMERA:
Enable/disable the channel number to detect motion.
MASK MOTION
Select a specific area for motion recording. The DVR system will
start recording when the selected area has been detected
motion. Use
,
,
and
move to the left, right, up, and down. Use
select the area.
33
buttons to
buttons to
OSD MENU
MAIN MENU
CAMERA
RECORD
HARD DRIVE
SENSOR / ALARM
MOTION
NETWORK
BACKUP
SYSTEM
Description
NETWORK SETUP
Setup the network parameters for the internet or intranet remote
monitor or playback.
NETWORK SETUP
IP MODE
NW ENABLE
VIDEO PORT
UPGARDE PORT
1 2 3
9 10 11
0080
5005
4
12
5
13
6
14
7
15
8
16
IP MODE
The system provides 3 types of IP setup mode – STATIC, DHCP,
and PPPOE.
IP MODE
IP MODE
IP ADDR ESS
SUB NET
GATEWAY
DNS
MAC ADDR ESS
CHANGE
STATIC
192 . 168 . 153 . 100
255 . 255 . 255 . 255
192 . 168 . 153 . 254
000 . 000 . 000 . 000
00 . 18 . 1A. 02 . 00 . 0F
Use
and
buttons to go up and down and
. Use
select IP MODE, and then press
buttons to change the selections and press
and
or
to make a selection.
STATIC: Assigns a constant IP address for the DVR system.
Use
and
buttons to go up and down
and select items, and then press
selection. Use
and
or
to make
to move left and right to
select or enter the configuration value.
- IP ADDRESS: Assign a constant IP address which a real
IP addresses give from ISP to DVR system.
i
Do Not assign the DVR to 1.0.0.0 network segment.
It will cause the DVR can not access to Internet due
to the un-recognize to 1.0.0.0 IP segment.
- SUBNET: It is a bitmask used to identify the sub network
and how many bits provide room for host addresses. Enter
the subnet mask of the IP address which user has
assigned to DVR system.
- GATEWAY: A network device act as a passageway to
internet. Enter the network gateway IP address
34
OSD MENU
IP MODE
IP MODE
IP ADDR ESS
SUB NET
GATEWAY
DNS
MAC ADDR ESS
GET IP
Description
DHCP
192 . 168 . 153 . 100
255 . 255 . 255 . 255
192 . 168 . 153 . 254
000 . 000 . 000 . 000
00 . 18 . 1A. 02. 00 . 0F
- MAC ADDRESS: Only for user information. Don’t need to
enter the MAC address.
- When all parameters are set, select the CHANGE to
confirm the configuration.
DHCP: Assign the IP address by local DHCP server to DVR
system.
The DHCP (Dynamic Host Configuration Protocol) is a
set of rules used by a communications device (such
as a computer, router or networking adaptor) to allow
the device to request and get an Internet address from
a server which has a list of addresses available for
assignment
i
Select GET IP to start getting IP. The DVR system will try to
get an IP address from the DHCP server. A message
window will show up as below:
G E T IP NO W . W A IT IN G . . .
If system didn’t get any network information, it means that
get IP from DHCP server fail.
PPPOE: Point-to-Point Protocol over Ethernet is a network
protocol for encapsulating PPP frames in Ethernet frames. It
is used mainly with ADSL services. If your network is using
ADSL service connecting to internet, and then, select
PPPOE mode, and then select GET IP. A message window
will show up as below:
G E T IP NO W . W A IT IN G . . .
If system didn’t get any network information, it means that
get IP from PPPOE server fail.
i
Please go to 8.1.1.5 Network Setup # PPPOE to
setup PPPOE account and password for connecting
to PPPOE server.
35
OSD MENU
Description
NETWORK SETUP
IP MODE
NW ENABLE
VIDEO PORT
UPGARDE PORT
1 2 3
9 10 11
0080
5005
4
12
5
13
6
14
7
15
8
16
NW ENABLE:
Allow internet remote user to playback or monitor the channels.
Without enabling the network function, the channels cannot be
playback or monitor from remote site.
VIDEO PORT:
A port for the remote connection. Any port can be assigned as a
video port, except the ports already used by the network
services. The default video port is 80.
UPGRADE PORT:
A port for the remote update DVR system firmware. Any port can
be assigned as an upgrade port, except the ports are already
used by the network services. The default upgrade port is 5005.
For Upgrading DVR firmware, please contact your local
dealer.
i
MAIN MENU
CAMERA
RECORD
HARD DRIVE
SENSOR / ALARM
MOTION
NETWORK
BACKUP
SYSTEM
Please DO NOT cut off the power of the DVR system
while the firmware is upgrading. Power failure will cause
the permanent damage of the DVR system.
BACKUP SETTING
Select the backup mode – USB or DVR+RW. A player
application will be included in the backup folder. Before starting
backup process, plug in the USB storage device or place the
DVR+RW disk into DVD-ROM drive.
USB: Using USB device (ex. Pen drive or External Hard
disk) to backup partial recorded video and playback on PC.
DVD+RW: backup partial recorded video on DVR+RW disk
and playback on PC.
BACK U P SETTING
BACKUP SELECT
USB
After select the backup mode, user need to select the backup
period and hard disk.
BAKCUP SETTING
HARD DISK
: HDD 1
START TIME
: 2008 / 01 / 04
END TIME
: 2001 / 01 / 05
1 2 3
9 10 11
CHANNEL
CALCULATE SIZE
BACKUP EXECUTE
1.
2.
3.
4
12
10 : 00 : 01
13 : 08 : 13
5
13
6
14
7
15
8
16
89MB
Select the START TIME and END TIME.
Select the channels which user wants to backup.
Select the CALCULATE SIZE to calculate the size of
selected backup file.
36
OSD MENU
Description
BAKCUP SETTING
HARD DISK
: HDD 1
START TIME
: 2008 / 01 / 04
END TIME
: 2001 / 01 / 05
CHANNEL
1 2 3
9 10 11
CALCULATE SIZE
BACKUP EXECUTE
4
12
4.
10 : 00 : 01
13 : 08 : 13
5
13
6
14
7
15
And then, select BACKUP EXECUTE and press YES
(ENTER) to start backup video
BACKUP IN PROCESS
8
16
89MB
15%
820M
AVAILABLE SIZE
5.
When backup is done, press any key to back to main menu.
USB BACKUP SUCCESSFUL
PRESS ANY KEY TO EXIT
i
MAIN MENU
CAMERA
RECORD
HARD DRIVE
SENSOR / ALARM
MOTION
NETWORK
BACKUP
SYSTEM
- Remember to plug in the USB device or insert the
DVR+RW disk into DVR-ROM drive before starting
to backup.
- The DVR system doesn’t supply the power to
external device. Therefore, the external device must
be power supplied by external power.
SYSTEM
SYSTEM SETUP
MULTI-QUAD:LIVE
MULTI-QUAD:PLAY
PASSWORD CHANGE
CONFIGURATION
TIME SETUP
AUTO RECORD
AUDIO MUTE
MUTLIPLE DVR
DVR ID
VGA RESOLUTION
TEMPERATURE
VIDEO SYSTEM
OSD TRANSPARENCY
LANGUAGE
OFF
OFF
OFF
1
1024x768
NTSC
LEVEL - 2
ENGLISH
AA . 01 . 01 . 00 . 06
AUTO RECORD
Enable/disable auto continue recording when interrupted (i.e.,
power breakdown, video playback or configuration setup). It
continue recording after 10 second of idleness. This is applicable
in Always Record mode.
MUTLIPLE DVR
Enable/disable multiple DVR system remote control. When user
has more than one DVR system, user can use MULTIPLE DVR
function to control all DVR system by single remote control.
37
OSD MENU
SYSTEM SETUP
MULTI-QUAD:LIVE
MULTI-QUAD:PLAY
PASSWORD CHANGE
CONFIGURATION
TIME SETUP
AUTO RECORD
AUDIO MUTE
MUTLIPLE DVR
DVR ID
VGA RESOLUTION
TEMPERATURE
VIDEO SYSTEM
OSD TRANSPARENCY
LANGUAGE
Description
OFF
OFF
OFF
1
1024x768
NTSC
LEVEL - 2
ENGLISH
AA . 01 . 01 . 00 . 06
DVR ID
Assign the ID number for multiple DVR system remote controls.
When there are more than one DVR systems, user can enable
MULTIPLE DVR function, and then assign DVR ID to each DVR
system. Then, user can just use one remote control to control all
DVR system by pressing DVR ID. To remote control multiple
DVR systems, press
and number key (DVR ID number)
on the remote control.
VIDEO SYSTEM
DVR system will auto detect the video system and display
OSD TRANSPARENCY
Adjust dark or light of OSD display windows.
LANGUAGE
Select from the available languages
MULTI-QUAD:LIVE
SAVE TO HOT-KEY
MODE:
QUAD1
QUAD2
QUAD3
QUAD4
QUAD5
QUAD6
FN+5
MULTI-QUAD:LIVE
DVR supports different kind of screen display modes in preview.
User can set each display mode to the number button as a
Hot-Key for switching.
1
3
4
6
8
10
SAVE TO HOT-KEY:
Select a hot-key for the display mode. A hot-key is a combination
of
button and number button. The number button starts
from 5 to 16 can be assigned as a hot-key number.
MODE:
Select the display mode for just selected hot-key. Display mode
has 8 kinds --
,
,
,
,
,
,
, and
.
Each mode can select channels (QUAD 1 ~ QUAD 16) for
displaying.
MULTI-QUAD:PLAY
SAVE TO HOT-KEY
MODE:
QUAD1
QUAD2
QUAD3
QUAD4
QUAD5
QUAD6
1
3
4
6
8
10
FN+5
MULTI-QUAD:PLAY
DVR supports different kind of screen display modes in playback.
User can set each display mode to the number button as a
Hot-Key for switching.
SAVE TO HOT-KEY:
Select a hot-key for the display mode. A hot-key is a combination
of
button and number button. The number button starts
from 5 to 16 can be assigned as a hot-key number.
MODE:
Select the display mode for just selected hot-key. Display mode
has 6 kinds -,
,
,
,
, and
. Each mode
can select channels (QUAD 1 ~ QUAD 16) for displaying.
38
OSD MENU
PASSWORD SETUP
PASSWORD SETUP
ADMINISTARATOR
OPERATOR
USER
Description
NO
PASSWORD CHANGE
Enable/disable full system password protection. This would
prevent unauthorized user to stop video recording, change
system settings and formatting the hard disk.
ADMINISTRATOR:
Administrator has the authority of formatting hard disk, changing
system settings, remote monitor the DVR system and changes
the system settings. The factory default password is 111111.
ADMINISTRATOR PASSWORD
CURRENT
NEW
CONFIRM
EXECUTE
******
******
******
OPERATOR:
The login account for remote connection through the internet.
User account only can view and playback recorded video by
Web viewer (ex: Internet Explorer), but no authority to change
the DVR system’s setting. The factory default password is
111111.
OPERATOR PASSWORD
CURRENT
NEW
CONFIRM
EXECUTE
******
******
******
USER:
The login account for general user. No superuser authority but
can preview live video. The factory default password is 111111.
USER PASSWORD
CURRENT
NEW
CONFIRM
EXECUTE
39
******
******
******
OSD MENU
SYSTEM SETUP
MULTI-QUAD:LIVE
MULTI-QUAD:PLAY
PASSWORD CHANGE
CONFIGURATION
TIME SETUP
AUTO RECORD
AUDIO MUTE
MUTLIPLE DVR
DVR ID
VGA RESOLUTION
TEMPERATURE
VIDEO SYSTEM
OSD TRANSPARENCY
LANGUAGE
Description
CONFIGURATION
Backup and resort the DVR system setting.
OFF
OFF
OFF
1
1024x768
CONFIGURATION SETUP
SAVE CONFIGURATION
RESTORE CONFIGURATION
NTSC
LEVEL - 2
ENGLISH
AA . 01 . 01 . 00 . 06
SAVE CONFIGURATION:
Backup the current DVR system setting to USB device. Plug in
the USB storage device before starting to save the configuration.
CONFIGURATION SETUP
SAVE CONFIGURATION
RESTORE CONFIGURATION
CONFIGURATION SAVE OK
RESTORE CONFIGURATION:
To restore the previous saved DVR system setting.
RESTOR FINISHED. SHUT DOWN DVR
40
OSD MENU
TIME SETUP
DATE FORMAT
DATE
TIME
AUTO SYNC TIME
TIME ZONE
LAST SYNC TIME
Description
YYYY/MM/DD
2008 / 03 / 12 WED
21 : 07 : 45
OFF
GMT
2008 / 01 / 01
00 : 00 : 00
TIME SETUP
Setup system date, time, daylight saving, and enable auto
synchronize time through network.
DATE FORMAT:
Select the display format of the date
DAYLIGHT SAVING
DATE :
Set the current date
TIME :
Set the current time
AUTO SYNC TIME:
Enable/disable time synchronization automatically through
network. The DVR system will auto synchronize time from NTP
servers. The first time synchronize will be 6 hours later after
system power up. When the daylight saving is enabling, the auto
time synchronization will be stopped.
- User need to setup the NTP server’s URL or IP
address. Please go to 8.1.1.1 System Setting #(3)
NTP Setting to setup the NTP server.
- If the NTP server doesn’t setup, the auto
synchronize time function will not work correctly.
i
TIME ZONE:
Select the time synchronization time zone. The time zone will
base on GMT (Greenwich Mean Time) time zone.
LAST SYNC TIME:
Display the latest time synchronization date and time.
DAYLIGHT SAVING
DAYLIGHT SAVING
START
END
TIME OFFSET
OFF
: 2007 / 03 /10
: 2007 / 10 /09
01 : 00
00 : 00
00 : 00
DAYLIGHT SAVING:
To enable/disable daylight saving function.
START:
Setup daylight start up date and time.
END:
Setup daylight stop date and time.
TIME OFFSET:
Assign a time that it is for daylight saving time offset in your time
zone. For example: if the time zone is in U.S. Eastern, the time
offset is 1 hour.
41
OSD MENU
TEMPERATURE SETUP
TEMPERATURE FORMAT
HIGH THRESHOLD
LOW THRESHOLD
DVR HOT PROTECT
Description
C
035
030
055
TEMPERATURE SETUP
Set the DVR unit temperature type and high/low threshold limit.
TEMPERATURE FORMAT:
Temperature pattern display on front LED panel.
HIGH THRESHOLD:
Set a specific temperature limited (0 ~ 100°C) for fan active.
When the hard disk temperature is higher than limited
temperature, the fan will be active. The default value is 35°C.
LOW THRESHOLD:
Set a specific temperature limited (0 ~ 30°C) for fan stop. When
the hard disk temperature is lower than limited temperature, the
fan will be stop. The default value is 30°C.
DVR HOT PROTECT:
Set the temperature limit to shutdown hard disk when the DVR
unit temperature is higher than (>) limited (55 ~ 70°C).
42
Chapter 4
4.1
Using the USB Playback Console
Recommended system requirements
Pentium®4 2.4GHZ or above
Windows®2000/ XP
DDR 256 MB
Graphic function must support DirectDraw
Audio card or built-in
Speaker
1 available USB2.0 port
4.2
Installing the USB Playback Console
To install the USB Playback Console:
1.
Place Installation CD into the CD-ROM drive. When the installation main screen appears, click
Install USB Playback Console and then follow the on screen instructions
2.
Select the language you prefer
3.
Click OK to install the application
4.
Click Exit to close the installation main screen. You may plug in the pen drive or external hard
disk now.
43
4.3
Running the USB Playback Console
To run the application, click the
icon on the PC desktop
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
(17)
(12)
(13)
(16)
Name
(1)
(14)
(15)
Function
Video playback screen
To select the video file for playing. The playback application supports *.dvr
and *.avf file.
(2)
Open File
- DVR Recorded File (HD): To playback the recorded video from the hard
disk which was recording video on the DVR system. (see also 4.3.2)
- Backup File(.dvr): The file is backup and save in *.dvr file format. (see
also 4.3.3)
- Backup File(.avf): The file is backup and save in *.avf file format. The
recorded video backup to pen drive is in *.avf (see also 4.3.4)
44
Name
Function
Select the event you want to playback. The event list only available when
user select to playback in DVR Recorded File(HD).
(3)
Event List
(4)
Full screen
Use the entire area of the screen to only display the video. To return, press
the right button of the mouse or ESC on the keyboard.
When you switch to full screen in multiple-screen mode, Left click to toggle
to only display one of the video in the multiple-screen mode or all.
(5)
Segment
Keep a portion of the recorded video (see also 4.3.1)
(6)
Output
Save the segmented file in *.mpg or *.avi format (see also 4.3.1).
(7)
Snapshot
Capture and save the image either in *.jpg or *.bmp format
(8)
Print
Print the image
(9)
HDD Backup
To call out HDD Backup application. (See Chapter 5)
(10) iEnhance
To call out iEnhance application. ( See Chapter 7)
(11) Watermark
To call out ImageVerification application. (See Chapter 6)
(12) Status Bar
Display the recorded date, time and play speed.
(13) Progress Bar
Show the progress of the file being played. You may move the bar to seek
at any location of the track.
(14) Playback
Controller
(15) Split Screen Mode
Begin: Move at the beginning of the recorded video file.
Previous: Go back to the previous frame by frame.
Slower: Play the recorded video file at the speed of 1/2X, 1/4X, or 1/8X.
Rewind: Wind back the recorded video file.
Pause: Briefly stop playing the recorded video file.
Play: Play the recorded video file.
Faster: Play the recorded video file at the speed of 2x, 4x, 8x, or 16x.
Next: Go to the next frame by frame.
End: Go to the end of the recorded video file.
Select from different screen view to playback the recorded video file of the
entire camera or one camera on screen.
Exit/ Minimize the application or chose Cancel to go back to the application
(16) Exit
(17) Sound /Sound bar
Turn on and off the sound
Increase and decrease the volume
45
4.3.1 To Cut and Save the Portion of the Recorded Video
1.
Use the Playback Control buttons or drag the bar on the playback progress bar and pause on
where you want to start the cut. Then, click Segment to set the begin mark.
2.
Use the Playback Control buttons or drag the bar on the playback progress bar and pause on
where you want to end the cut. Then, click Segment to set the end mark. To cancel
segmentation, click Segment button again.
3.
Click Output button to save the wanted portion.
4.
In the Save As dialog box, locate on where user wants to save the file, type the filename, and
select the video format.
4.3.2 Playback DVR Recorded File from Hard Disk
1.
2.
3.
4.
5.
Please have the hard disk which containing of recorded video data install on your PC or using
external USB enclosure to connect to your PC.
Click Open File button
Select DVR Recorded File(HD) and click OK.
Select the hard disk drive from Select Disk window and click OK.
And then, the File Select window appears. Select the event that user wants to play and click
OK. Click Next to go next page and click Pre to go back last page of event list. Also, enter the
page number in page column and click go can direct go to the page.
46
4.3.3 Playback Backup File(*.dvr)
1.
2.
3.
Click Open File button.
Select Backup File(*.dvr) and click OK.
Locate the backup file folder and click OK.
i
4.
When open the backup video file, just locate the where folder of backup file is.
And then, Playback Date/Time Selection window appears. Select the date and time and click
OK.
4.3.4 Playback Backup File (*.avf)
To playback backup file in *.avf format, user can use the AVFPlayback application that included in
backup folder when backup into USB storage device. Also, user can use USB Playback Console to
playback backup file (see also 4.3).
1. Plug the USB storage device into PC USB port.
2. Run AVFPlayback from USB storage device
3. Click Open in AVFPlayback UI
4. Click Select Folder to locate the backup files
5. And then, select the backup file and click OK
47
Chapter 5
5.1
Backup Recorded Video File
Recommended system requirements
Pentium®4 2.4GHZ or above
Windows®2000/ XP
DDR 256 MB
Graphic function must support DirectDraw
Audio card or built-in
Speaker
1 available USB2.0 port
5.2
Familiarizing with HDD Backup Application
(2)
(1)
(3)
(4)
(5)
(6)
(7)
(8)
(12)
Name
(11)
(9)
(10)
Function
No.: the list order number
Record: the record type(see also Chapter 2.3.1)
Begin Time: the beginning of record time
End Time: the end of record time
(1)
All recorded video
events list
(2)
Video Display
Display first frame of each recorded channel video which user had
selected.
(3)
Progress bar
Show the progress of the event being played. User may move the bar to
seek at any location of the track
48
Name
(4)
Source Disk
To select the hard disk drive
(5)
Target Path
To locate on where user want to save the file
(6)
Event (%)
Display the backup progress rate of event in percentage
(7)
Total (%)
Display the total backup progress rate in percentage
(8)
Stop
Stop backup progress
(9)
Start
Start backup progress
(10) Page Switch
Pre: go back last page
Next: go to next page
Page column: enter the page number and click Go button to go to the
page
(11) Select All
Select all listed recorded video events. Click the check box again to cancel
for selecting all events.
(12) Set Marked File
Use Ctrl and mouse to select the multiple events from event list, and then
click Set Marked File to mark multiple events. When click Set Marked File
button, the marked event will turn to un-mark and un-mark event will turn to
marked.
5.3
1.
Function
To Backup Recorded Video File
Please have the hard disk which was recording video on the DVR system install on your PC or
using external USB enclosure to connect to your PC.
2.
To run the HDD Backup application, click the HDD Backup button on USB Playback
Application main interface.
3.
Click Browse in Source Disk to locate the recorded video file.
4.
And then, the Select Disk windows will appear as below:
5.
Select the hard disk drive from Select Disk windows. All available hard disk will list on the
Select Disk windows with size and name
49
6.
Select the hard disk drive and click OK
7.
And then, all the recorded video files will list out.
8.
Select the event which user wants to backup. Or mark the Select All to select all listed
recorded video event
9.
Locate on where user wants to save the backup file
10. Click Start to process backup
11. To stop the backup progress, click Stop
12. To play the backup file, see 4.3.3.
50
Chapter 6
ImageVerification
Image Verification is a watermark-checking program to identify the authenticity of a saved image
(e.g. by snapshot). This program can only verify uncompressed bmp image files.
6.1
1.
To Run the ImageVerification
To run the ImageVerification application, click the Watermark button on USB Playback
Console main interface.
2.
In the ImageVerification screen, click Load Source Image and locate the image source.
3.
Click Verify Image to begin the process.
4.
Check the result in the Processed Image screen. If the picture is unmodified, the image in the
Source Image and Processed Image screen would be exactly the same. If the picture is
being modified, a warning dialog box would prompt and the modified area is highlighted.
51
Chapter 7
iEnhance
The bundled iEnhance is a video editing tool and can only be used with *.dvr video file. It allows you
to adjust the video picture quality, segment and save the selected portion of the video, zoom in and
out the image, and print or save the screen shot. You can also save the setting and apply it on other
files.
To run iEnhance application, click iEnhance button on USB Playback Console interface.
(16)
(15)
(17)
(18)
(14)
(19)
(13)
(12)
(20)
(21)
(11)
(22)
(23)
(24)
(25)
(10)
(9)
(1)
Name
(2) (3) (4)
(5)
(6)
(7) (8)
Function
(1) Open File
Access *.dvr video file.
(2) Save Image
Capture and save the screen shot in *.bmp format.
(3) Playback Control
Buttons
Begin: Move at the beginning of the video file.
Previous: Go back to the previous frame.
Rewind: Wind back the video file.
Pause: Temporary stop playing the video file.
Play: Play the video file.
Faster: Play the video file at the speed of 2x, 4x, or 8x.
Next: Go to the next frame.
End: Go to the end of the video file.
(4) Save Video
Save the edited or segmented video in *.avi format.
(5) Print
Print the screen shot.
(6) Segment
Mark the beginning and the end of the selected portion of the video. Two
triangle marks will appear on the slider. To cancel video segmentation, click
this button again.
(7) Zoom Buttons
Enlarge, reduce, and set the image back to normal size.
(8) Full Screen
Use the entire screen to only display the video.
(9) Default
Set the video back to original state and delete all the changes in the history
box.
(10) History Box
List all the actions.
(11) Undo
Delete the last action.
52
Name
Function
(12) Noise Reduce
Adjust the softness and repair the damaged colours.
(13) Sharpness
Improve the overall image by enhancing edges. This gives the image more
depth.
(14) Effects
Gray Scale: convert the image into black and white (monochrome).
Normalize: adjust the brightness intensity.
Equalize: automatically adjust the images that are too dark.
De-interlace: smooth out the overlying frames.
Static: de-interlace for motionless scene.
Dynamic: de-interlace for moving scene.
(15) Picture
Adjustment
Adjust the Brightness, Contrast, Saturation, Hue and Gamma.
(16) Original Screen
Display the original state of the image.
(17) Temporary
Setting Block
Display the sample settings. Click the sample to apply the setting on the
current video.
(18) Status Bar
Display the date, and time of the video.
(19) Progress Bar
Show the progress of the file being played. You may move the bar to seek at
any location of the track.
(20) iStable
To reduce the jolt in the recorded video.(also see Chapter 7.1)
(21) Add Setting
Include the new setting to the temporary setting block.
(22) Rename
Change the name of the selected setting in the temporary setting block.
(23) Delete
Permanently remove the selected setting in the temporary setting block.
(24) Load Setting
Call the saved settings.
(25) Save Setting
Store the settings in the temporary setting block.
7.1
To Use iStable
The iStable function can reduce the jolt in the recorded video.
1. Click Open File button and select the recorded video.
2. And then, click iStable button.
3. iStable windows will show up.
4. Select the smoothness level – 1(Low), 2,
3, 4, and 5(High). The default value is 3.
5. Click Play button, and then iStable function
will start to initial the recorded video.
6. When the initialize is done, user will see
the original and stabilized recorded video
play in two windows. The original video on
the right side of window and the stabilized
video on the left side of window.
53
Chapter 8
Using the Remote Programs
User can use Microsoft Internet Explorer to access DVR system by entering the IP address. To use
this feature, make sure that you PC and EB5416DVD Pro both are connected to the internet and the
Network feature is enabled.
Accessing this feature for the first time you will be prompted by your browser to install
WebCamX.cab, allow the installation and you should be able to connect and login afterwards.
For Windows 2000, click Yes when the Security Warning dialog box appears.
For Windows XP, click Install when the Internet Explorer - Security Warning dialog box appears.
After installing the WebCamX.cab and when connecting to the DVR system, you are required to
enter User ID (Superuser or User) and password (default password is 111111) and select the type of
network. Superuser has the authority to remote setup the DVR system configuration on Web
Viewer.
i
Changing the Superuser and User default password is strongly recommended.
54
8.1
Familiarizing the Web Viewer Buttons
Right-clicking on the Web Viewer video screen, enables you to start video recording, change video
quality, switch camera and enable/disable DirectDraw.
Name
Function
(1) DirectDraw
i
Enhance the video quality.
Not all graphic cards can support this function. If you can not see the screen display correctly
or screen is messed, please check with VGA card vendor.
(2) Received file size
Indicate the size of the data being sent per second.
(3) Camera frames
Indicate the number of frames per second.
(4) One screen view
To view single camera view on screen. User can right click on the screen to
switch to different camera view.
(5) Split screen view
To view all cameras on screen simultaneously.
(6) Record
Start to record the video of the selected camera in AVI format. Directly click
screen to select the channel that user wants to record and press Record
button.
(7) Remote Console
Initiate Remote Console. It allows you to control DVR server (see also
Chapter 8.2).
(8) Remote setup
Change the DVR server settings (see also Chapter 8.1.1).
i
Only Superuser has the authority to remote setup DVR system.
(9) PTZ Control
Initiate PTZ camera controller(see also Chapter 8.3)
(10) Snapshot
Capture and save the screen shot in *.bmp format.
(11) Full screen
Use the entire area of the screen to only display the video.
To return, Right click the mouse or press ESC on the keyboard.
55
Name
(12) Select cameras to
view
Function
Select to the view camera from different server. In Select Camera dialog box,
Display column, click to enable/disable viewing the camera.
Click Add Server and select the server type between DVR and IP Cam to
add.
Click Delete Server to delete the selected item.
Click Import to load the previous saved list.
Click Export to save the list.
Click Apply All to change all the camera video quality based on the selected
setting.
Click OK to exit.
56
8.1.1 To Setup Remote System Setting
Click OK to exit and save the setting and Cancel to exit without saving the setting. The setting here
applies to Remote DVR system only.
i
-
After changed the DVR system setting, refresh your web browser in order to apply the new
setting to the DVR system.
-
8.1.1.1
Only the superuser has the authority to change remote DVR system settings.
System Setup
(1)
(2)
(4)
(3)
(5)
(1) Recording Setting
- Auto Record
Enable/disable auto continue recording when interrupted (i.e., power breakdown, video
playback or configuration setup). It continue recording after 10 second of idleness. This is
applicable in Always Record mode.
- Disk Overwrite
Enable/disable replacing the earliest record when the hard disk space runs out. By default,
the HDD overwrite setting is enabled
- RECORD MODE
Select D1/CIF recording mode. Under D1 mode, the video recording is in full screen
resolution and takes turns from one channel to the next one when Auto Scan enables. Each
channel is recorded only at a maximum frame rate of 15fps. User can switch to view the
video in full screen or QUAD screen. Whereas in CIF mode, video recording is at a lower
resolution, but each video is recorded in 30fps/25fps (NTSC/PAL). User can switch to view
the video in full screen or QUAD screen
- RECORD FRAMERATE
Select the number of frames per second to be recorded. Refer to the table below for the
available record frame rate settings. The higher the frame rate is, it uses more hard disk
space
57
Video Standard
NTSC
PAL
Record Mode
-
D1
16, 80, 240
16, 80, 200
CIF
16, 80, 160, 240, 480
16, 80, 200, 400
VIDEO QUALITY
Select the video quality setting from BEST, HIGH, MEDIUM, GOOD, NORMAL or LOW.
BEST – best record quality but less record hours
LOW – longest record hour but quality is ordinary
NORMAL – allows you to record more hours but the quality of the recorded video is
moderate.
(2) NTP Setting
Setup the time auto synchronization.
- Enable NTP
Enable/disable time synchronization automatically through network. The DVR system will
auto synchronize time from NTP servers which user has entered in following server 1 and
server 2 column.
i
-
-
When the daylight saving is enabling, the auto time synchronization will be stopped.
TIME ZONE:
Select the time synchronization time zone. The time zone will base on GMT (Greenwich
Mean Time) time zone.
Server 1/Server 2
Fill in the network time server URL or IP address (clock.stdtime.gov.tw or
time.stdtime.gov.tw)
(3) MISC
- Auto Scan
Enable/disable auto cycle switch to display the next channel when in full screen preview.
User can set different switch time for each channel. The time range is from 5 ~30 seconds.
Click Auto Scan Time to set the auto scan time period.
- Audio Out Select
Select the channel to output the audio signal. Please make sure the audio output device
(such as a speaker) is connected to DVR unit.
- Audio Mute
Enable/disable to hear audio sound of local DVR. To hear sound, make sure the unit is
connected to an audio output device (ex: speaker). If user recorded video in audio mute
status, there is no sound when playback
- Time Format
Select the display format of the date
- VGA Resolution
Select the display resolution
(4) DLS
Setup daylight saving settings.
- Enable DLS
To enable/disable daylight saving function.
58
-
START
Setup daylight start up date and time.
END
Setup daylight stop date and time.
TIME OFFSET
Assign a time that it is for daylight saving time offset in your time zone. For example: if the
time zone is in U.S. Eastern, the time offset is 1 hour.
(5) TEMPERATURE
Set the DVR unit temperature type and high/low threshold limit.
- TEMPERATURE FORMAT:
Temperature pattern display on front LED panel.
- HIGH THRESHOLD:
Set a specific temperature limited (0 ~ 100°C) for fan active. When the hard disk
temperature is higher than limited temperature, the fan will be active. The default value is
35°C.
- LOW THRESHOLD:
Set a specific temperature limited (0 ~ 30°C) for fan stop. When the hard disk temperature is
lower than limited temperature, the fan will be stop. The default value is 30°C.
- DVR HOT PROTECT:
Set the temperature limit to shutdown hard disk when the DVR unit temperature is higher
than (>) limited (55 ~ 70°C).
8.1.1.2
Camera Setup
(1)
(2)
(5)
(3)
(4)
(1) Camera icon
Select the camera that user wants to set up.
(2) Camera Title
Enter a name for the camera
(3) Network Audio Enable
Enable/disable the audio sound record when recording the video through network.
(4) Video Adjustment
Select the camera and adjust the Brightness, Contrast, Hue and Saturation of the selected
camera. Click Default Value to set all video setting back to the default.
59
8.1.1.3
Record Setup
(1)
(2)
(3)
(5)
(4)
(1) Camera icon
Select the camera that user wants to set up.
(2) Record Select
Enable/disable the channel number to record video
i
The channels which could be recorded should be enabled in the CAMERA SELECT first.
(3) Audio Record
Enable/disable channel number audio recording. To record sound, make sure the microphone is
connected to the unit
(4) Record Schedule
By default, in 24 hours, the recording schedule is set to always record every hour. Refer to the
table below to customize the recoding condition
Condition
Description
NO REC
Disable video recording
ALWAYS REC
Record non-stop
MOTION REC
Start recording when any movement is detected
SENSOR REC
Start recording when the sensor has triggered
(5) Motion Detection
-
Motion Camera Enable
Enable/disable the channel number to detect motion.
Motion Record Time
Set the amount of time (in second) to record when a motion has detected.
Sensitivity
Set the sensitivity level. The sensitivity is from high, 9~ 2 and low.
60
8.1.1.4 Alarm/Sensor Setup
(1)
(2)
(3)
(4)
(1) Alarm
- ALARM OUT
Select the way of alarming – BUZZER, RELAY-1, RELAY-2, RELAY-3, RELAY-4, or ALL.
- The Condition of Alarm
Select the condition that it will trigged the alarm
HD Fail Alarm
Enable/disable send out alarm when hard disk is failed.
Motion Alarm
Select the channel that will send out the alarm when motion has been detected
Video Loss Alarm
Select the channel that will send out the alarm when video is lost.
Sensor Alarm
Select the channel that will be send out the alarm when sensor has been triggered
- E-Mail Setup
SMTP
Enter the SMTP server IP
User ID & Password
Enter User ID and Password for e-mail server user identification
From
Enter the sender e-mail address
To
The recipient e-mail address and separate it with a semicolon
Subject
Enter the message title
Message
Type the message
61
-
Alarm Out Time
Set the amount of time (in second) to continue sending the alarm once activated
(3) Sensor Setup
- Sensor Status
Customize the initial state of the attached sensor for every camera. Refer to the table below
to customize the sensor state.
Not installed: Indicates that there is no sensor connected
Normal open: Indicates that the initial state of the sensor is normal open. Video
recording initiate when there is a changes in the sensor state
Normal close: Indicates that the initial state of the sensor is normal close. Video
recording initiate when there is a changes in the sensor state
- Sensor Record Time
Set the amount of time (in second) to record after the sensor has been triggered
(4) Spot Monitor
To display channel alarm event in full screen mode when the sensor is activated or motion is
detected. When there are multiple alarm events, DVR system will display the last alarm event.
- Sensor
Select the channel that will send out the alarm event for display when the sensor has been
triggered.
- Motion
Select the channel that will send out the alarm event for display when the motion has been
detected.
- Camera
Select the channel to display alarm event.
- Call Monitor Time
Set a period time (0 ~ 255 sec) for alarm event to display on surveillance screen.
62
8.1.1.5
Network Setup
(1)
(2)
(4)
(3)
(5)
(1) IP Mode
Select the IP Mode – Static IP, DHCP, or PPPOE
-
DHCP
Assign the IP address by local DHCP server to DVR system.
i
The Dynamic Host Configuration Protocol (DHCP) is a set of rules used by a
communications device (such as a computer, router or networking adaptor) to allow the
device to request and get an Internet address from a server which has a list of addresses
available for assignment.
(2) Option
- Remote Audio Recording
Enable/disable audio recording when recording at remote site.
- Server Port
A port is using for the remote connection. Any port can be assigned as a server port, except
the ports already used by the network services.
- UPNP Enable
Enable/disable UPnP function that can automatically configure the port setting to the local
router.
- UPNP Port
Assign a port for UPNP service using.
(3) DDNS
DDNS (Dynamic Domain Name Service) is a data query service mainly used on the Internet for
translating domain names into Internet addresses. Users can register their own domain name
on http://www.ddns.avers.com.tw. (See Appendix A)
- Domain Name
Enter the domain name that user wanted.
- Auth Key
A password use to access DDNS to register the domain name. MAC address of the DVR
system is the key for user to register the domain name on AVerMedia DDNS web site. To
find MAC address of your DVR system, follow the steps below:
1. In OSD menu, select NETWORK SETUP
63
2. Select any one of IP mode
3. A NETWORK INFORMATION windows will show
up MAC address of DVR system is display as
shown
IP MODE
IP MODE
IP ADDR ESS
SUB NET
GATEWAY
DNS
MAC ADDR ESS
CHANGE
STATIC
192 . 168 . 153 . 100
255 . 255 . 255 . 255
192 . 168 . 153 . 254
000 . 000 . 000 . 000
00 . 18 . 1A. 02. 00 . 0F
(4) Static IP
Assign a fixed and global IP address for the DVR system
-
IP: Assign a constant IP address which real IP
addresses from ISP.
-
Mask:
i
Enter the subnet mask of the IP address which user has assigned to DVR system.
It is a bitmask used to tell how many bits in an octet(s) identify the subnetwork,
and how many bits provide room for host addresses.
-
Gateway: Enter the network gateway IP address
-
DNS: Domain Name Server translates domain names (such as www.abb.com.tw) to IP
addresses. It will translate the domain name into IP address when DVR system request.
(5) PPPOE
Point-to-Point Protocol over Ethernet is a network protocol for encapsulating PPP frames in
Ethernet frames. It is used mainly with ADSL services.
User ID & Password: fill in the user account and password that user applied from your ISP for
PPPOE connection.
64
8.1.1.6
User Setting
Click Remote setup button on Web Viewer main interface, and then, click User button to call out
the Password Change interface.
(1)
(2)
(3)
(1) Superuser
Change the remote accessing password of superuser. Superuser has the authority to remote
setup the DVR system configuration on Web Viewer.
- Password
Enter the new password
- Password Confirm
Re-enter password to confirm
(2) Network User
The login account for remote connection through the internet. User account only can view and
playback recorded video by Web viewer (ex: Internet Explorer), but no authority to change the
DVR system’s setting. The factory default password is 111111.
- Password
Enter the new password
- Password Confirm
Re-enter password to confirm
(3) User
Change the remote accessing password of user
- Password
Enter the new password
- Password Confirm
Re-enter password to confirm
65
8.2
Familiarizing the Remote Console Buttons
(12)
(11)
(10)
(9)
(13)
(8)
(1)(2)
Name
(3)
(4)
(5)
(6)
(7)
Function
(1) Exit
Close the Remote Console.
(2) Audio button
Enable/disable the sound.
(3) Split Screen Mode
Select from six (6) different split screen type to playback the recorded video
file of all the camera, or one camera over the other or alongside on a single
screen.
i
If there are only 4 cameras, you won’t be able to switch to 9, 16, and 13 split screen mode.
(4) Record
Start/stop video recording.
(5) Network
Enable/disable remote system access. This feature allows you to access EB
DVR server from a remote location via internet connection.
(6) Setup
Configure the Remote Console setting. (see also Chapter 8.2.1)
(7) Preview
Switch to Preview/Playback mode. This allows you to view live camera
display.
(8) Playback
Switch to Playback mode. This allows you to view the recorded video file.
(see also Chapter 8.4)
(9) Status Bar
Display the current date, time and hard disk free space.
(10) Camera ID
Show the number of cameras that are being viewed. When you are in single
screen mode, click the camera ID number to switch and view other camera.
(11) Snapshot
Capture and save the screen shot either in *.jpg or *.bmp format.
(12) Full screen
Use the entire area of the screen to only display the video.
To return, Right click the mouse or press ESC on the keyboard.
(13) DirectDraw
Enable/disable DirectDraw function
i
Direct Draw function supports for certain VGA card. For more information, please contact your
VGA card vendor.
66
8.2.1 To Setup Remote Console Setting
Click Setup button to call out the System Setting windows. Click OK to exit and save the setting
and Cancel to exit without saving the setting.
(1)
(1)
(1)
(1)
(1) Storage Path
Set the directory on where to save the data. When there is not enough free space to record one
hour data, the system automatically replaces the oldest data. In case you have more than one
storage path, the system automatically saves the data to the next storage path. By default the
data is stored in C:\RemoteData, to insert another storage path, click Add. To remove the
selected path, click Delete.
-
Enable network storage
Select the Enable network storage check box to send the recorded video in
network-attached storage.
i
To add network storage, the Internet storage drive/folder must be mapped as
Network Driver in DVR server. To know how to assign or connect to a network drive,
please refer to your Windows help file and search “Map Network drive”.
(2) Language
Customize the system to display the tool tips and dialogs based on the selected language. By
default the language is in English.
(3) Remote Server
Enter the DVR Server IP and Server Port number.
(4) Channel Settings
The numbers from 1 to 4 represent the camera ID. In
Transmitting Channels section, enable the camera number
to receive the camera signal from the server. In Visible
Channels section, enable the camera number to view the
camera signal on Remote Console screen. To select all the
cameras, enable the ALL check box.
67
8.3
Familiarizing the WebViewer PTZ Buttons
(1)
(2)
(3)
(4)
(5)
Name
(1) Direction buttons
(2) Zoom +/(3) Select PTZ
(4) Focus +/(5) Camera preset
position number
8.4
Function
Adjust and position the focal point of the PTZ camera. Click the center to pan
automatically.
Zoom in and out the image.
Choose to enable/disable the PTZ camera. In the Select PTZ dialog box, Select
column, click to enable/disable viewing and controlling the PTZ camera.
Click OK to exit and save the setting and Cancel to exit without saving the
setting.
Adjust the focus manually to produce clear image.
Move the PTZ camera to the preset point. The reset point (1~9) is based on the
user has setup by remote control at local site.
Using the Remote Playback
To use this feature, first you need to select the source of the file. Click the Playback button. And
then, in the Select Playback Mode dialog box, choose Local Playback to open the file that is
recorded in the Remote Console, and Remote Playback to open the file that is recorded in the
DVR server. When you choose Remote Playback, select Download and Playback.
Click OK to proceed and Cancel to void this operation.
In the Video Playback Date/Time Selection, the number from 00 to 23 represent the time in 24-hour
68
clock. The numbers from 01 to 16 represent the camera number.
To Make a Selection:
1. Select the date in the calendar. Use
and
buttons to shift the calendar to the left or right.
2. In the table below, click on the blue block to select and open the recorded file. The blue block
turns red when it is selected. The block that appears in white doesn’t have data. You can only
select one block when you choose Download and Playback.
3. Click OK to proceed and Cancel to void this operation.
4. If you select Download Playback and after making the selection, the system divides the selected
hour into 16 video thumbnails. In the Time Selection screen, click on the video thumbnail you
want to download (see also Chapter 8.3.2).
69
8.4.1 Familiarizing the Local Playback Buttons
(13)
(12)
(11)
(10)
(9)
(8)
(7)
(1) (2)
(3)
(4)
(5)
(6)
Name
Function
Select from six (6) different split screen type to playback the recorded video
(1) Split Screen Mode
file of all the camera, or one camera over the other or alongside on a single
screen.
- If there are only 4 cameras, you won’t be able to switch to 9, 16, and 13 split screen mode.
- To zoom in an area on the screen, Right click and Drag a square on the area you want to
enlarge. To back to normal view, right click the channel screen again.
i
(2) Progress bar
Show the progress of the file being played. You may move the bar to seek at
any location of the track.
(3) Hour Buttons
Select and click to playback the recorded video file on the specific time frame.
i
The Hour buttons represent the time in 24-hour clock. The blue bar on top of the hour button
indicates that there is a recorded video file on that period of time. If there is no recorded data
within the hour, there will be no color bar on top of the hour button. While the red bar indicates that
you are currently viewing the recorded video file.
(4) Playback Control
Buttons
(5) Date
i
Begin: Move at the beginning of the recorded video file.
Previous: Go back to the previous frame.
Slower: Play the recorded video file at the speed of ½x, ¼x, or ⅛x.
Rewind: Wind back the video file.
Pause: Briefly stop playing the recorded video file.
Play: Play the recorded video file.
Faster: Play the recorded video file at the speed of 2x, 4x, or 8x.
Next: Go to the next frame.
End: Go to the end of the video file.
Select the date on the calendar and the time from 00 to 23 to where to start
playing the recorded video file.
The numbers from 00 to 23 represent the time in 24-hour clock. The numbers from 01 to 16
represent the camera ID. While the red colored column indicates on where to start playing the
recorded video file. If there is no any video data, it will be no color bar on top of the date button.
(6) Preview
Switch to Preview/Playback mode.
(7) Playback
Switch to Playback mode. This allows you to view the recorded video file.
(8) Status bar
Display the record date, time, HDD capacity in preview mode and play speed
70
Name
Function
in playback mode.
(9) Camera ID
Show the number of cameras that are being viewed. When you are in single
screen mode, click the camera ID number to switch and view other camera.
(10) Output
Save the segmented file in *.mpg, *.avi, or *.dvr format (see also Chapter
8.3.1.1).
(11) Segment
Keep a portion of the recorded video you want (see also Chapter 8.3.1.1).
(12) Snapshot
Capture and save the screen shot either in *.jpg or *.bmp format.
(13) Full screen
View in Playback-compact mode. To return, press the right button of the
mouse or ESC on the keyboard.
8.4.1.1 To Cut and Save the Wanted Portion of the Recorded Video
1.
Use the Playback Control buttons or drag the bar on the playback progress bar and pause on
where you want to start the cut. Then, click Segment to set the begin mark.
2.
Use the Playback Control buttons or drag the bar on the playback progress bar and pause on
where you want to end the cut. Then, click Segment to set the end mark. To cancel
segmentation or set the segment marks from the start, click Segment button again.
3.
Click Output button to save the wanted clip.
4.
In the Save As dialog box, locate on where you want to save the file, type the filename, and
select the video format.
71
8.4.2
Familiarizing the Download and Playback Buttons
(8)
(7)
(6)
(5)
(1)
(2)
Name
(3)
(4)
Function
(1) Progress bar
Show the progress of the file being played. You may move the bar to seek at any
location of the track.
(2) Playback
Control Buttons
Begin: Move at the beginning of the video file.
Previous: Go back to the previous frame.
Slower: Play the recorded video file at the speed of 1/2x, 1/4x, or 1/8x.
Rewind: Wind back the video file.
Pause: Briefly stop playing the recorded video file.
Play: Play the recorded video file.
Faster: Play the recorded video file at the speed of 2x, 4x, 8x, or 16x.
Next: Go to the next frame.
End: Go to the end of the video file.
(3) Date
Open other file.
(4) Output
Save the segmented file in *.mpg or *.avi format.
(5) Print
Print the screen shot.
(6) Save
Save the screen shot either in *.jpg or *.bmp format and video in *.dvr format.
(7) Segment
Keep a portion of the recorded video you want. You may follow the instruction in
Chapter 8.3.1.1.
72
Warranty Notice
LIMITED WARRANTY
AVerMedia INFORMATION, Inc. warrants this product to be free of defects resulting from faulty manufacture or
components under the following terms:
WARRANTY LENGTH
Labor is warranted for (1) one year from the date of purchase
Parts are warranted for (1) one year from the date of purchase
Replacement products will be warranted for the remainder of the one year warranty period or (30) thirty days, whichever is
longer
WHO IS PROTECTED
This warranty is enforceable only by the first consumer purchaser
WHAT IS AND IS NOT COVERED
Except as specified below, this warranty covers all defects resulting from faulty manufacturing of this product. The
following are not covered by the warranty.
1. Any product on which the serial number has been defaced, modified, or removed
2. Damage, deterioration, or malfunction resulting from:
Accident, abuse, misuse, neglect, fire, water, lightning, or other acts of nature, commercial or industrial use,
unauthorized product modification, or failure to follow instructions included with the product.
Misapplication of service by someone other than the manufacturer’s representative
Any shipment damages (Claims must be made with carrier)
Any other cause which does not relate to a product defect
3. Cartons, cases, batteries, cabinets, tapes, or accessories used with product
4. AVerMedia does not warrant that this product will meet your requirements; it is your responsibility to determine
the suitability of this product for your purpose
WHAT WE WILL AND WILL NOT PAY FOR
We will pay labor and material expenses for covered items. However, we will not pay for the following:
1. Removal or installation charges
2. Shipping charges
3. Any incidental charges
EXCLUSION OF DAMAGES
THE MANUFACTURER’S SOLE OBLIGATION AND LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR
OR REPLACEMENT OF A DEFECTIVE PRODUCT AT OUR OPTION. THE MANUFACTURER SHALL NOT, IN ANY
EVENT, BE LIABLE TO THE PURCHASER OR ANY THIRD PARTY FOR ANY INCIDENTAL OR CONSEQUENTIAL
DAMAGE (INCLUDING, BUT NOT LIMITED TO, DAMAGES RESULTING FROM INTERRUPTION OF SERVICE AND
LOSS OF BUSINESS) OR LIABILITY IN TORT RELATING TO THIS PRODUCT OR RESULTING FROM ITS USE OR
POSSESSION.
LIMITATIONS OF IMPLIED WARRANTIES
There are no other oral or written warranties, expressed or implied, including but not limited to those of merchantability or
fitness for a particular purpose. Any implied warranties are limited in duration to one year from the date of purchase
STATE LAW AND YOUR WARRANTY
This warranty gives you specific legal rights, and you may also have other rights granted under state law. These rights
vary from state to state
CONTACT INFORMATION
Taiwan & International
No. 135, Jian Yi Rd., Chung Ho City, Taipei, Taiwan
TEL: 886-2-2226-3630
FAX: 886-2-2226-7241
Web Site: http://www.avermedia.com / http://www.averdigi.com
73