Axis Communications 241Q Security Camera User Manual

Models 750/751/754/774/794
Soft Serve Freezers
Operating Instructions
028754--M
2/01/02
Complete this page for quick reference when service is required:
Taylor Distributor:
Address:
Phone:
Service:
Parts:
Date of Installation:
Information found on the data label:
Model Number:
Serial Number:
Electrical Specs:
Voltage
Cycle
Phase
Maximum Fuse Size:
A
Minimum Wire Ampacity:
A
E February, 2002 Taylor
All rights reserved.
028754--M
The word Taylor and the Crown design
are registered trademarks in the United States
of America and certain other countries.
Taylor Company
750 N. Blackhawk Blvd.
Rockton, IL 61072
Table of Contents
Section 1
To the Installer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Water Connections (Water Cooled Units Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Air Cooled Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1
1
1
Section 2
To the Operator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Compressor Warranty Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
2
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
Section 4
Operator Parts Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Model 750 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Model 751 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Model 754 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Model 774 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Model 774 Topping Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Model 794 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Models 750 & 751 Single Spout Door and Beater Assembly . . . . . . . . . . . . . . . .
Models 754, 774 & 794 Three Spout Door and Beater Assembly . . . . . . . . . . . .
4
4
5
6
7
8
9
10
11
Section 5
Important: To the Operator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Symbol Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MIX LOW Indicator Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MIX REF Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
STANDBY Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WASH Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AUTO Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reset Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Air Tube . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjustable Draw Handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12
12
13
13
13
13
13
13
14
14
14
Section 3
Models 750, 751, 754, 774, 794
Table of Contents
Table of Contents -- Page 2
Section 6
Operating Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Prior to Set-Up (Model 774) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sanitizing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Priming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Closing Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Draining Product From The Freezing Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rinsing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brush Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15
15
15
20
22
23
23
23
23
24
24
Section 7
Important: Operator Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
During Cleaning and Sanitizing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Troubleshooting Bacterial Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Regular Maintenance Checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Winter Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
25
25
25
25
26
Section 8
Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
27
Section 9
Parts Replacement Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
30
Section 10
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wiring Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
31
42
Note: Continuing research results in steady improvements; therefore, information
in this manual is subject to change without notice.
Table of Contents
Models 750, 751, 754, 774, 794
Section 1
To the Installer
Electrical Connections
This machine is designed for indoor use only.
Each freezer requires one power supply for each data
label. Check the data label(s) on the freezer for fuse,
circuit ampacity and electrical specifications. Refer to
the wiring diagram provided inside of the electrical box,
for proper power connections.
DO NOT install the machine in an area where
a water jet could be used to clean or rinse the machine.
Failure to follow this instruction may result in serious
electrical shock.
In the United States, this equipment is intended to be
installed in accordance with the National Electrical
Code (NEC), ANSI/NFPA 70--1987. The purpose of
the NEC code is the practical safeguarding of persons
and property from hazards arising from the use of
electricity. This code contains provisions considered
necessary for safety. Compliance therewith and
proper maintenance will result in an installation
essentially free from hazard!
Water Connections
(Water Cooled Units Only)
An adequate cold water supply must be provided with
a hand shut-off valve. On the underside rear of the
base pan, two 3/8” I.P.S. (for single-head units) or two
1/2” I.P.S. (for double-head units) water connections
for inlet and outlet have been provided for easy
hook-up. 1/2” inside diameter water lines should be
connected to the machine. (Flexible lines are
recommended, if local codes permit.) Depending on
local water conditions, it may be advisable to install a
water strainer to prevent foreign substances from
clogging the automatic water valve. There will be only
one water “in” and one water “out” connection for both
single-head and double-head units. DO NOT install a
hand shut-off valve on the water “out” line! Water
should always flow in this order: first, through the
automatic water valve; second, through the
condenser; and third, through the outlet fitting to an
open trap drain.
In all other areas of the world, equipment should be
installed in accordance with the existing local codes.
Please contact your local authorities.
Stationary appliances which are not equipped with a
power cord and a plug or other device to disconnect
the appliance from the power source must have an
all--pole disconnecting device with a contact gap of at
least 3 mm installed in the external installation.
CAUTION: THIS EQUIPMENT MUST BE
PROPERLY GROUNDED! FAILURE TO DO SO
CAN RESULT IN SEVERE PERSONAL INJURY
FROM ELECTRICAL SHOCK!
Beater rotation must be clockwise as viewed looking
into the freezing cylinder of any model freezer.
Note: The following procedures should be
performed by a trained service technician.
Air Cooled Units
To correct rotation on a three-phase unit, interchange
any two incoming power supply lines at freezer main
terminal block only.
The model 750 air cooled unit requires a minimum of
6” (152 mm) of clearance on both sides and 0” in the
rear of the unit. The model 751, 754, 774 and 794 units
require 3” on all sides. This will allow for adequate air
flow across the condenser(s). Failure to allow
adequate clearance can reduce the refrigeration
capacity of the freezer and possibly cause permanent
damage to the compressor.
To correct rotation on a single-phase unit, change the
leads inside the beater motor. (Follow diagram printed
on motor.)
Electrical connections are made directly to the
terminal block provided in the main control box located
under the upper left side panel on the Model 750, or
050418
Models 750, 751, 754, 774, 794
1
To the Installer
Section 2
To the Operator
Compressor Warranty Disclaimer
The freezer you have purchased has been carefully
engineered and manufactured to give you dependable
operation. The Taylor Company soft-serve models
covered in this manual consist of the following: 750,
751, 754, 774, and 794.
The refrigeration compressor(s) on this machine are
warranted for the term indicated on the warranty card
accompanying this machine. However, due to the
Montreal Protocol and the U.S. Clean Air Act
Amendments of 1990, many new refrigerants are
being tested and developed, thus seeking their way
into the service industry. Some of these new
refrigerants are being advertised as drop-in
replacements for numerous applications. It should be
noted that, in the event of ordinary service to this
machine’s refrigeration system, only the refrigerant
specified on the affixed data label should be used.
The unauthorized use of alternate refrigerants will void
your compressor warranty. It will be the owner’s
responsibility to make this fact known to any technician
he employs.
These units, when properly operated and cared for, will
produce a consistent quality product. Like all
mechanical products, they will require cleaning and
maintenance. A minimum amount of care and
attention is necessary if the operating procedures
outlined in this manual are followed closely.
This Operator’s Manual should be read before
operating or performing any maintenance on your
equipment.
Your Taylor freezer will NOT eventually compensate
for and correct any errors during the set-up or filling
operations. Thus, the initial assembly and priming
procedures are of extreme importance. It is strongly
recommended that personnel responsible for the
equipment’s operation, both assembly and
disassembly, go through these procedures together in
order to be properly trained and to make sure that no
confusion exists.
It should also be noted that Taylor does not warrant the
refrigerant used in its equipment. For example, if the
refrigerant is lost during the course of ordinary service
to this machine, Taylor has no obligation to either
supply or provide its replacement either at billable or
unbillable terms. Taylor does have the obligation to
recommend a suitable replacement if the original
refrigerant is banned, obsoleted, or no longer available
during the five year warranty of the compressor.
In the event you should require technical assistance,
please contact your local authorized Taylor Distributor.
If the crossed out wheeled bin symbol is
affixed to this product, it signifies that this product is
compliant with the EU Directive as well as other similar
legislation in effect after August 13, 2005. Therefore,
it must be collected separately after its use is
completed, and cannot be disposed as unsorted
municipal waste.
The Taylor Company will continue to monitor the
industry and test new alternates as they are being
developed. Should a new alternate prove, through our
testing, that it would be accepted as a drop-in
replacement, then the above disclaimer would
become null and void. To find out the current status of
an alternate refrigerant as it relates to your
compressor warranty, call the local Taylor Distributor
or the Taylor Factory. Be prepared to provide the
Model/Serial Number of the unit in question.
The user is responsible for returning the product to the
appropriate collection facility, as specified by your local
code.
For additional information regarding applicable local
laws, please contact the municipal facility and/or local
distributor.
050818
To the Operator
2
Models 750, 751, 754, 774, 794
Section 3
Safety
We at Taylor Company are concerned about the safety
of the operator when he or she comes in contact with
the freezer and its parts. Taylor has gone to extreme
efforts to design and manufacture built-in safety
features to protect both you and the service technician.
As an example, warning labels have been attached to
the freezer to further point out safety precautions to the
operator.
DO NOT allow untrained personnel to
operate this machine.
S DO NOT operate the freezer unless all
service panels and access doors are
restrained with screws.
S DO NOT remove the door, beater and
blades, or drive shaft unless all control
switches are in the OFF position.
S DO NOT put objects or fingers in door
spout.
Failure to follow these instructions may result in
contaminated product or severe personal injury to
fingers or hands from hazardous moving parts.
S
IMPORTANT -- Failure to adhere to the
following safety precautions may result in severe
personal injury. Failure to comply with these
warnings may also damage the machine and its
components. Component damage will result in
part replacement expense and service repair
expense.
To Operate Safely:
USE EXTREME CAUTION when removing
the beater assembly. The scraper blades are very
sharp and may cause injury.
DO NOT operate the freezer without reading
this operator’s manual. Failure to follow this instruction
may result in equipment damage, poor freezer
performance, health hazards, or personal injury.
This freezer must be placed on a level
surface. Failure to comply may result in personal injury
or equipment damage.
DO NOT obstruct air intake and discharge openings:
Counter Model: 6” (152 mm) minimum air space on
both sides and 0” on the rear.
Console Models: 3” (76 mm) minimum air space on
all sides.
DO NOT operate the freezer unless it is
properly grounded.
S DO NOT attempt any repairs unless the
main power supply to the freezer has been
disconnected.
S DO NOT operate the freezer with larger
fuses than specified on the freezer data
label.
Failure to follow these instructions may result in
electrocution or damage to the machine. Contact your
local authorized Taylor Distributor for service.
S
Failure to follow this instruction may cause poor
freezer performance and damage to the machine.
These freezers are designed to operate indoors, under
normal ambient temperatures of 70_--75_F
(21_--24_C). The freezers have successfully
performed in high ambient temperatures of 104_F
(40_C) at reduced capacities.
NOISE LEVEL: Airborne noise emission does not
exceed 78 dB(A) when measured at a distance of 1.0
meter from the surface of the machine and at a height
of 1.6 meters from the floor.
DO NOT use a water jet to clean or rinse the
freezer. Failure to follow this instruction may result in
serious electrical shock.
050418
Models 750, 751, 754, 774, 794
3
Safety
Section 4
Operator Parts Identification
Model 750
Item
Description
Part No.
1
Cover A.-Hopper
X38458
2
Gasket-Hopper Cover
3
Tube A.-Feed
4
Item
Description
Part No.
10
Panel-Side Left
050741
038375
11
Leg-4” SS w/O-Ring
013458
X29429-2
12
Louver-Side-Left
013631
Panel-Rear
020891
13
Stud-Nose Cone
022822
5
Panel-Upper Side Right
042317
14
Panel A.-Front
X50754
6
Pan-Drip
050766
15
O-Ring-.643 OD x .077 W
018572
7
Panel-Right Side
050742
16
O-Ring-3/8 OD x .070 W
016137
8
Shield-Splash
022763
17
Orifice
022465-100
9
Tray-Drip
013690
Operator Parts Identification
4
Models 750, 751, 754, 774, 794
Model 751
Item
Description
Part No.
Item
Description
Part No.
1
Cover A.-Hopper
X38458
11
Panel-Service
047170
2
Gasket-Hopper Cover
038375
12
Caster-Swivel
018794
3
Tube A.-Feed
X29429-2
13
Stud-Nose Cone
022822
4
Panel-Rear
013637
14
Panel A.-Side-Lower-Louvered
X39075
5
Panel-Upper Side Right
028823
15
O-Ring-.643 OD x .077 W
018572
6
Pan-Drip 11-5/8 Long
027503
16
O-Ring-3/8 OD x .070 W
016137
7
Panel A.-Lower Side Right
X24424
17
Orifice
022465-100
8
Shield-Splash
022763
18
Louver-Side (Left & Right)
017471
9
Tray-Drip 14-7/8 x 5-1/8
013690
19
Panel A.-Front
X33237
Panel-Upper Side Left
024426
20
Adaptor A.-Caster
X18915
10
Models 750, 751, 754, 774, 794
5
Operator Parts Identification
Model 754
Item
Description
Part No.
Item
Description
Part No.
1
Cover A.-Hopper
X38458
11
Panel-Upper Side Left
028822
2
Gasket-Hopper Cover
038474
12
Stud-Nose Cone
022822
3
Tube A.-Feed
X29429-2
13
Panel A.-Side Lower Left
X46447
4
Panel-Rear
053782
14
Louver-Side (Left & Right)
017471
5
Panel-Upper Side Right
028823
15
O-Ring-.643 OD x .077 W
018572
6
Panel A.-Side Lower Right
X46448
16
O-Ring-3/8 OD x .070 W
016137
7
Panel-Service
046584
17
Orifice
022465-100
8
Shield-Splash
022766
18
Pan-Drip 17-1/4” Long
027504
9
Tray-Drip
014533
19
Panel A.-Front
X32956
Caster-Swivel
018794
20
Adaptor A.-Caster
X18915
10
Operator Parts Identification
6
Models 750, 751, 754, 774, 794
Model 774
Item
Description
Part No.
Item
Description
Part No.
1
Cover A.-Hopper
X38458
14
Pump A.-Syrup-Tan
053794--TAN
2
Gasket-Hopper Cover
038474
15
O-Ring-.643 OD x .077 W
018572
3
Tube A.-Feed
X29429-2
16
Panel A.-Side Lower-Left
X46447
4
Panel-Upper Rear
X42574
17
Jar-Syrup-Plastic
036573
5
Panel-Upper Side Right
028823
18
Jar-Syrup-Stainless-Shallow
036574
6
Panel A.-Side Lower-Right
X46448
19
Stud-Nose Cone
022822
7
Panel-Service
047077
20
Louver-Side (Left & Right)
017471
8
Shield-Splash
022766
21
Panel-Lower Rear
053837
9
Tray-Drip
014533
22
O-Ring-3/8 OD x .070 W
016137
10
Caster-Swivel
018794
23
Orifice
022465-100
11
Panel-Upper Side Left
028822
24
Panel A.-Front
X42539
12
Pan-Drip 17-1/4” Long
027504
25
Adaptor A.-Caster
X18915
13
Lid with Ladle 1 oz.
036575
Models 750, 751, 754, 774, 794
7
Operator Parts Identification
Model 774 Topping Pump (053794--)
ITEM
DESCRIPTION
PART NO.
1
Knob-Plunger-Tan
032762-TAN
1
Knob-Plunger-Brown
032762-BRN
1
Knob-Plunger-Red
032762-RED
2
O-Ring-9/16 OD x .103 W
016369
3
Nut-Plunger
036577
4
Collar-Gaging 1/2 Ounce
035514
5
Tube-Plunger
032757
6
Insert-Plunger
032758
7
Spring-Plunger
032761
8
Washer-Nylon
032760
9
Plunger
036578
Seal Assembly
X33057
10
10a
O-Ring-13/16 OD x .103 W
019330
11
Body-Syrup Pump
047934
12
Nut-Spout
036821
13
Lid-Pump
036822
14
Tube-Discharge
050912
15
O-Ring-1-5/16 OD x .103 W
048149
16
O-Ring-1 OD x .103 W
048148
17
Kit-Valve-Captured Ball Shallow
048166-001
Includes:
1 - Body A.-Pump Valve
1 - O-Ring-1-5/16 OD x .103W (048149)
1 - Brush-cleaning (054068)
1 - Instruction Sheet-Installation/Cleaning
Operator Parts Identification
8
Models 750, 751, 754, 774, 794
Model 794
Item
Description
Part No.
Item
Description
Part No.
1
Cover-Hopper 14 Qt. Grey
041682-GRY
10
Caster
018794
2
Pan-Drip 19-1/2 Long
035034
11
Panel A.-Side Lower Left
X46447
3
Tube A.-Feed
X29429-2
12
Louver-Side (Left & Right)
017471
4
Panel-Rear
041855
13
Stud-Nose Cone
022822
5
Panel-Upper Side (Left & Right)
024426
14
O-Ring-3/8 OD x .070 W
016137
6
Panel A.-Side Lower Right
X46448
15
O-Ring-.643 OD x .077 W
018572
7
Panel-Service
041856
16
Orifice
024465-100
8
Shield-Splash
022765
17
Panel A.-Front
X41820
9
Tray-Drip
020157
18
Adaptor A.-Caster
X18915
Models 750, 751, 754, 774, 794
9
Operator Parts Identification
Models 750 & 751 Single Spout Door and Beater Assembly
ITEM
DESCRIPTION
PART NO.
ITEM
DESCRIPTION
PART NO.
1
HANDLE A.- DRAW
X55096
7
O-RING 5/16OD X .070W
016272
1a
DRAW HANDLE
028804
8
PLUG-PRIME
028805
1b
SCREW-ADJUST
055092
9
O-RING-PRIME PLUG
016137
1c
O-RING 1/4OD X .070W
015872
10
PIN A.- PIVOT
X22820
1d
NUT-JAM
029639-BLK
11
GASKET-DOOR HT 4”
048926
2
NUT-STUD FLAT LONG
021508
12
BLADE- SCRAPER
035174
3
DOOR A.- 1-SPOUT
X51531-10
13
BEATER A.- HELICORE
X31761
4
VALVE A.- DRAW
X18303
14
BEARING-FRONT
050216
5
O-RING 7/8OD X .070W
014402
15
SHAFT-BEATER
032564
6
CAP-DESIGN
014218
16
SEAL-DRIVE SHAFT
032560
Operator Parts Identification
10
Models 750, 751, 754, 774, 794
Models 754, 774 & 794 Three Spout Door and Beater Assembly
Item
Description
Part No.
Item
Description
Part No.
1
Handle A.-Draw
X55096
7
Seal-Drive Shaft
032560
1a
Draw Handle
028804
8
Cap-Design
014218
1b
Screw-Adjustment
055092
9
Decal-Door
021521
1c
O-Ring 1/4 OD x .070 W
015872
10
Door A.-3 Spout
X51532-12
1d
Nut--Jam
029639--BLK
11
Rod A.-Pivot
X20683
2
Nut-Stud Long
034382
12
O-Ring 5/16 OD x .070 W
016272
3
Nut-Stud Short
034383
13
Gasket-Door HT 4”
048926
4
Valve A.-Draw
X18303
14
Bearing-Front
050216
5
O-Ring 7/8 OD x .070 W
014402
15
Beater A.-Helicore
X31761
6
Shaft-Beater
032564
16
Blade-Scraper
035174
Models 750, 751, 754, 774, 794
11
Operator Parts Identification
Section 5
Important: To the Operator
750/751
754/774/794
ITEM
1
2
3
4
5
6
7
Symbol Definitions
DESCRIPTION
MIX LOW INDICATOR LIGHT
MIX REFRIGERATION KEY
STANDBY KEY
WASH KEY
AUTO KEY
POWER ON/OFF (TOGGLE)
RESET BUTTON
Important: To the Operator
To better communicate in the International arena, the
words on many of our operator switches and keys have
been replaced with symbols to indicate their functions.
Your Taylor equipment is designed with these
International symbols.
12
Models 750, 751, 754, 774, 794
STANDBY Key
The following chart identifies the symbol definitions.
The Separate Hopper Refrigeration System (SHR)
and the Cylinder Temperature Retention System
(CTR) are standard features on these machines. The
SHR incorporates the use of a separate small
refrigeration system to maintain the mix in the hopper
below 40_(4.4_C) to assure bacteria control. The CTR
works with the SHR to maintain a good quality product.
During long “No Sale” periods, it is necessary to warm
the product in the freezing cylinder to approximately
35_F to 40_F (1.7_C to 4.4_C) to prevent overbeating
and product breakdown.
= OFF
= ON
= MIX
= STANDBY
= WASH
To activate the SHR and CTR, press the STANDBY
key. Remove the air orifice and place the air tube (end
without the hole) into the mix inlet hole.
= AUTO
When placed in the ON position, the power switch
allows SOFTECH control panel operation.
When the STANDBY key is pressed, the light comes
on, indicating the CTR (Cylinder Temperature
Retention System) has been activated. In the
STANDBY mode, the WASH and AUTO functions are
automatically cancelled. The MIX REF function is
automatically locked in to maintain the mix in the
hopper.
MIX LOW Indicator Light
To resume normal operation, press the AUTO key.
When the unit cycles off, the product in the freezing
cylinder will be at serving viscosity. At this time, place
the air tube (end with the hole) into the mix inlet hole
and install the air orifice.
Power Switch
Located on the front of the machine is a mix level
indicating light. When the light is flashing, it indicates
that the mix hopper has a low supply of mix and should
be refilled as soon as possible. Always maintain at
least 3” (7.6 cm) of mix in the hopper. If you neglect to
add mix, a freeze-up may occur. This will cause
eventual damage to the beater, blades, drive shaft,
and freezer door.
WASH Key
When the WASH key is pressed, the light comes on.
This indicates beater motor operation. The STANDBY
or AUTO modes must be cancelled first to activate the
WASH mode.
AUTO Key
When the AUTO key is pressed, the light comes on.
This indicates that the main refrigeration system has
been activated. In the AUTO mode, the WASH or
STANDBY functions are automatically cancelled. The
MIX REF function is automatically locked in to
maintain the mix in the mix hopper.
MIX REF Key
When the MIX REF key is pressed, the light comes on
indicating the mix hopper refrigeration system is
operating. For the Models 754, 774, and 794 the MIX
REF is controlled by the left side of the freezer as
viewed from the operator end. The MIX REF function
cannot be cancelled unless the AUTO or STANDBY
modes are cancelled first.
Models 750, 751, 754, 774, 794
Note: An indicating light and an audible tone will
sound whenever a mode of operation has been
pressed. To cancel any function, press the key again.
The light and mode of operation will shut off.
13
Important: To the Operator
Reset Button
draw handle is raised, new mix and air from the
hopper will flow down into the freezing cylinder.
This will keep the freezing cylinder properly
loaded and will maintain overrun.
On counter models, the reset button is located on the
side of the unit. On console models, the reset button
is located in the service panel. The reset protects the
beater motor from an overload condition. If an overload
occurs, the reset mechanism will trip. To properly reset
the freezer, press the AUTO key to cancel the cycle.
Turn the power switch to the OFF position. Press the
reset button firmly.
2.
The air orifice is used to meter a certain amount
of air into the freezing cylinder. The air orifice
maintains overrun and allows enough mix to enter
the freezing cylinder after a draw.
Do not use metal objects to press the reset
button. Failure to follow this instruction may
result in electrocution.
Turn the power switch to the ON position. Press the
WASH key and observe the freezer’s performance.
Open the side access panel. Make sure the beater
motor is turning the drive shaft in a clockwise direction
(from the operator end) without binding.
Adjustable Draw Handle
If the beater motor is turning properly, press the WASH
key to cancel the cycle. Press the AUTO key to resume
normal operation. If the freezer shuts down again,
contact a service technician. (For Models 754, 774,
and 794 press the AUTO key on both sides of the unit
to resume normal operation.)
These units feature an adjustable draw handle to
provide the best portion control. The draw handle
should be adjusted to provide a flow rate of 5 to 7-1/2
oz. (148 to 222 ml) of product per 10 seconds. To
INCREASE the flow rate, turn the screw
COUNTERCLOCKWISE.
Turn
the
screw
CLOCKWISE to DECREASE the flow rate. During
“Sanitizing” and “Rinsing”, the flow rate can be
increased by removing the pivot pin and placing the
restrictive bar on the TOP. When drawing product,
always place the restrictive bar on the bottom.
Air Tube
The air tube serves two purposes. One end of the tube
has a hole and the other end does not.
Figure 1
1.
Figure 2
After priming the machine, lubricate the o-rings
on the air tube (the end with the hole) and
place it into the mix inlet hole. Every time the
Important: To the Operator
During long “No Sale” periods, remove the air
orifice. Lubricate the o-rings on the air tube (the
end without the hole), and place it into the
mix inlet hole. This will prevent any mix from
entering the freezing cylinder.
IMPORTANT: Once the draw rate is set, tighten the
lock nut with a wrench.
14
Models 750, 751, 754, 774, 794
Section 6
Operating Procedures
The Model 751 has been selected to illustrate the
step-by-step operating procedures for all models
contained in this manual. These models, for all
practical purposes of operation, are the same.
Step 3
Prepare a pail of an approved 100 PPM sanitizing solution (example: Kay-5r). USE WARM WATER AND
FOLLOW THE MANUFACTURER’S SPECIFICATIONS. Sanitize the topping pumps by placing the
entire pump assembly in the pail of sanitizing solution.
Pump the solution through the assembly to thoroughly
sanitize the pump.
Each unit stores mix in a hopper. The mix then flows
by gravity through an air tube down into the freezing
cylinder. They all have 3.4 quart (3.2 liter) capacity
freezing cylinders. The Models 750, 751, 754, and 774
have 20 quart (18.9 liter) mix hoppers. The Model 794
has 14 quart (13.2 liter) mix hoppers.
Step 4
Remove the two topping pumps. Fill each stainless
syrup jar with topping. Replace the topping pumps in
the syrup jars.
Duplicate the following procedures, where they apply,
for the second freezing cylinder on Models 754, 774,
and 794.
Assembly
We begin our instructions at the point where we enter
the store in the morning and find the parts
disassembled and laid out to air dry from the previous
night’s cleaning.
Note: When lubricating parts, use an approved food
grade lubricant (example: Taylor Lube).
These opening procedures will show you how to
assemble these parts into the freezer, sanitize them,
and prime the freezer with fresh mix in preparation to
serve your first portion.
MAKE SURE POWER SWITCH IS IN THE
“OFF” POSITION! Failure to follow this instruction
may result in severe personal injury from hazardous
moving parts.
If you are disassembling the machine for the first time
or need information to get to this starting point in our
instructions, turn to page 24, “Disassembly”, and start
there.
Step 1
Install the drive shaft. Lubricate the groove and shaft
portion that comes in contact with the bearing on the
beater drive shaft. Slide the seal over the shaft and
groove until it snaps into place. DO NOT lubricate the
hex end of the drive shaft. Fill the inside portion of the
seal with 1/4” more lubricant and lubricate the flat side
of the seal that fits onto the rear shell bearing.
Prior to Set-Up (Model 774)
Step 1
Remove the two stainless syrup jars with topping
pumps from the syrup rail. Check the water level in the
heated syrup topping well. Make sure the water is filled
to the indicating mark on the bottom of the well. The
heated rail should have 32 oz. (946.2 ml) of water.
Step 2
Place the heater switch in the ON position.
Note: This heating process will take approximately
2-1/2 hours to reach temperature. The water level in
the topping wells must be checked at least once daily.
Models 750, 751, 754, 774, 794
Figure 3
15
Operating Procedures
Insert the drive shaft into the freezing cylinder, hex end
first, and into the rear shell bearing until the seal fits
securely over the rear shell bearing. Engage the hex
end firmly into the drive coupling. Be sure the drive
shaft fits into the drive coupling without binding.
Figure 6
Slide the beater the remainder of the way into the
freezing cylinder and over the end of the drive shaft.
The beater should fit snugly, but not so tightly that the
beater cannot be turned slightly to engage the drive
shaft. If the beater slides in too easily with little or no
resistance, there will not be enough force against the
beater to hold the blades in place. If this is the case,
contact your authorized Taylor service technician.
Figure 4
Step 2
Take one of the scraper blades and slip it under the
hook at the front of the beater. Wrap the blade around
the beater following the helix and pushing the blade
down onto the helix as you wrap. At the back end of the
beater, slip the blade under the hook. Repeat this
step for the second scraper blade.
Repeat steps 1 and 2 for the other side of the freezer
on Models 754, 774, and 794.
Step 3
Assemble the freezer door. Place the large rubber
gasket(s) into the groove(s) on the back side of the
freezer door.
Slide the white plastic front bearing(s) over the baffle
rod(s) onto the bearing hub(s) making certain that the
flanged end of the bearing is resting against the freezer
door.
Note: Do not lubricate the gasket(s) or the front
bearing(s).
Figure 5
Holding the beater securely, slide the beater one third
of the way into the freezing cylinder. Looking into the
freezing cylinder, align the hole at the rear of the beater
with the flats on the end of the drive shaft.
Operating Procedures
Figure 7
16
Models 750, 751, 754, 774, 794
Note: There are two gaskets and two front bearings
for the Models 754, 774, and 794 door, one for each
freezing cylinder.
Insert the prime plug(s) into the hole(s) in the top of the
freezer door, and push down.
Figure 10
Step 4
Install the freezer door. Insert the baffle rod(s) through
the opening in the beater(s) and seat the door flush
with the freezing cylinder. With the door seated on the
freezer studs, install the handscrews. Tighten equally
in a crisscross pattern to insure the door is snug.
Figure 8
Slide the two o-rings into the grooves on the prime
plug(s). Apply an even coat of Taylor Lube to the
o-rings and shaft(s).
Note: On Models 754, 774 and 794, short
handscrews go on the bottom and the long
handscrews go on top.
Figure 9
Note: There are two prime plugs for the Models 754,
774 and 794 door, one for each freezing cylinder.
Models 750, 751, 754, 774, 794
Figure 11
17
Operating Procedures
Step 5
Install the draw valve(s). Slide the two o-rings into the
grooves on the draw valve(s), and lubricate.
Step 6
Install the adjustable draw handle(s). Slide the o-ring
into the groove on the pivot pin, and lubricate.
Figure 14
Slide the fork over the bar in the slot of the draw valve.
Secure with pivot pin.
Figure 12
Note: Models 754, 774 and 794 have three draw
handles. Slide the fork of the draw handle in the slot of
the draw valve, starting from the right. Slide the pivot
pin through each draw handle as you insert them into
the draw valves.
Note: Models 754, 774 and 794 have three draw
valves.
Lubricate the inside of the freezer door spout(s), top
and bottom, and insert the draw valve(s) from the
bottom until the slot in the draw valve(s) comes into
view.
Figure 15
Note: These units feature adjustable draw handles to
provide the best portion control. The draw handles can
be adjusted for different flow rates. See page 14 for
more information on adjusting these handles.
Figure 13
Operating Procedures
18
Models 750, 751, 754, 774, 794
Model 794: Slide the rear drip pan into the hole in the
front panel.
Step 7
Snap the design cap(s) over the end of the door
spout(s).
Step 10
Slide two o-rings on one end of the air tube. Slide two
o-rings on the other end of the air tube.
Figure 16
Step 8
Install the front drip tray and the splash shield under
the door spout(s).
Figure 19
Slide the small o-ring into the groove of the air orifice.
Do not lubricate the o-ring.
Figure 17
Step 9
Slide the rear drip pan(s) into the hole in the side panel.
Figure 20
Note: Make sure the hole in the air orifice is clean and
is not clogged. If the hole in the air orifice should
become clogged, use soap and hot water to clear the
hole. Do not enlarge the hole in the air orifice.
Figure 18
Models 750, 751, 754, 774, 794
19
Operating Procedures
Install the air orifice into the hole in the top of the air
tube (in the end without the small hole on the side).
Figure 22
Step 3
While the solution is flowing into the freezing cylinder,
brush clean the mix hopper. When cleaning the
hopper, take particular care in brushing the mix level
sensing probe on the rear wall of the hopper, the mix
inlet hole, the air tube, and the hopper gasket.
Figure 21
Step 11
Lay the air tube (with the air orifice installed) and the
hopper gasket in the bottom of the mix hopper for
sanitizing.
Note: The Models 754 and 774 have one hopper
gasket for each mix hopper. The Model 794 does not
require a hopper gasket.
Repeat steps 10 and 11 for the other side of the
freezer on Models 754, 774 and 794.
Figure 23
Sanitizing
Step 1
Prepare two gallons (7.6 liters) of an approved 100
PPM sanitizing solution (example: Kay-5r). USE
WARM WATER AND FOLLOW THE MANUFACTURER’S SPECIFICATIONS.
Step 2
Pour the two gallons (7.6 liters) of sanitizing solution
into the hopper and allow it to flow into the freezing
cylinder.
Operating Procedures
Figure 24
20
Models 750, 751, 754, 774, 794
Step 6
Place an empty pail beneath the door spout and raise
the prime plug.
Figure 25
Step 4
Place the power switch in the ON position.
Figure 28
Step 7
When a steady stream of sanitizing solution is flowing
from the prime plug opening in the bottom of the
freezer door, lower the draw handle. Draw off all the
sanitizing solution.
Figure 26
Step 5
Press the WASH key. This will cause the sanitizing
solution in the freezing cylinder to agitate. Allow it to
agitate for five minutes.
Figure 29
Note: On Models 754, 774 and 794, momentarily pull
the center draw handle down to sanitize the center
door spout.
Step 8
Once the sanitizer stops flowing from the door spout,
raise the draw handle and press the WASH key,
cancelling the beater motor operation.
Note: You have just sanitized the freezer. Be sure
your hands are sanitized before continuing these
instructions.
Figure 27
Models 750, 751, 754, 774, 794
21
Operating Procedures
Step 2
Once a steady stream of mix starts to flow from the
prime plug opening in the bottom of the freezer door,
push down the prime plug.
Step 9
Assemble the hopper gasket around the top edge of
the mix hopper. Stand the air tube in the corner of the
hopper.
Figure 32
Figure 30
Step 3
Lubricate the o-rings on the air tube on the end with the
small hole on the side.
Repeat steps 1 through 9 for the other side of the
freezer on Models 754, 774 and 794.
Step 4
Install the air tube (the end with the hole) with the air
orifice installed into the mix inlet hole in the mix hopper.
Priming
Step 5
Press the AUTO key. The AUTO light will come on
indicating the main refrigeration system is operating.
When the unit cycles off, the product will be at serving
viscosity.
Step 1
With a pail beneath the door spout, lower the draw
handle. Be sure the prime plug is still in the UP
position. Pour two gallons (7.6 liters) of fresh mix into
the mix hopper and allow it to flow into the freezing
cylinder. This will force out any remaining sanitizing
solution. When full strength mix is flowing from the
door spout, raise the draw handle.
Note: On Models 751, 754, 774, and 794 the MIX
REF light will come on, indicating the mix refrigeration
system is operating to maintain the mix in the mix
hopper.
Note: Use only fresh mix when priming the freezing
cylinder.
Figure 33
Step 6
Fill the hopper with mix. As the mix level comes in
contact with the mix level sensing probe on the rear
wall of the hopper, the MIX LOW light will shut off.
Figure 31
Operating Procedures
22
Models 750, 751, 754, 774, 794
Rinsing
Step 7
Place the mix hopper cover in position over the mix
hopper.
Step 1
Pour two gallons (7.6 liters) of cool clean water into the
mix hopper. With the brushes provided, scrub the mix
hopper, mix inlet hole and mix level sensing probe.
Repeat steps 1 through 7 for the other side of the
freezer on Models 754, 774, and 794.
Step 2
With a pail beneath the door spout, raise the prime plug
and press the WASH key.
Closing Procedure
Step 3
When a steady stream of rinse water is flowing from
the prime plug opening in the bottom of the freezer
door, lower the draw handle. Drain all the rinse water
from the freezing cylinder, raise the draw handle and
press the WASH key cancelling the WASH mode.
To disassemble your unit, the following items will be
needed:
S
S
S
S
S
Two cleaning pails
Sanitized stainless steel rerun can with lid
Necessary brushes (provided with freezer)
Cleaner
Single service towels
Repeat steps 1 through 3 for the other side of the
freezer on Models 754, 774 and 794.
Cleaning
Draining Product From The
Freezing Cylinder
Step 1
Prepare two gallons (7.6 liters) of an approved cleaning solution (example: Kay-5r). USE WARM WATER
AND FOLLOW THE MANUFACTURER’S SPECIFICATIONS.
Step 1
Press the AUTO key, cancelling compressor and
beater motor operation.
Step 2
Push down the prime plug. Pour the two gallons (7.6
liters) of cleaning solution into the mix hopper.
Press the MIX REF key, cancelling the mix hopper
refrigeration system.
Step 2
Remove the hopper cover, hopper gasket and air tube.
Take these parts to the sink for cleaning.
Step 3
While the solution is flowing into the freezing cylinder,
brush clean the mix hopper, mix level sensing probe,
and the mix inlet hole.
Step 3
With a sanitized pail beneath the door spout, press the
WASH key. Lower the draw handle and drain the
remaining product from the freezing cylinder and mix
hopper.
Step 4
Press the WASH key. This will cause the cleaning
solution in the freezing cylinder to agitate.
Step 5
Place an empty pail beneath the door spout and raise
the prime plug.
Step 4
When the flow of product stops, press the WASH key,
and raise the draw handle. If local health codes permit,
empty the rerun into a sanitized stainless steel can.
Cover the container and place it in the walk-in cooler.
Step 6
When a steady stream of cleaning solution is flowing
from the prime plug opening in the bottom of the
freezer door, lower the draw handle. Draw off all of the
solution.
Repeat steps 1 through 4 for the other side of the
freezer on Models 754, 774 and 794.
Step 7
Once the cleaner stops flowing from the door spout,
raise the draw handle and press the WASH key
cancelling the WASH mode.
ALWAYS FOLLOW LOCAL HEALTH CODES.
Models 750, 751, 754, 774, 794
23
Operating Procedures
Note: To remove o-rings, use a single service towel to
grasp the o-ring. Apply pressure in an upward direction
until the o-ring pops out of its groove. With the other
hand, push the top of the o-ring forward and it will roll
out of the groove and can be easily removed. If there
is more than one o-ring to be removed, always remove
the rear o-ring first. This will allow the o-ring to slide
over the forward rings without falling into the open
grooves.
Repeat steps 1 through 7 for the other side of the
freezer on Models 754, 774 and 794.
Disassembly
MAKE SURE POWER SWITCH IS IN THE
“OFF” POSITION! Failure to follow this instruction
may result in severe personal injury from hazardous
moving parts.
Step 4
Remove the o-rings from the air tube(s) and air
orifice(s).
Step 1
Remove the handscrews, freezer door(s), beater(s),
scraper blades, and drive shaft(s) from the freezing
cylinder(s). Take these parts to the sink for cleaning.
Step 5
Return to the freezer with a small amount of cleaning
solution. Brush clean the rear shell bearing(s) at the
back of the freezing cylinder(s) with the black bristle
brush.
Step 2
Remove the front drip tray and the splash shield.
Brush Cleaning
Step 1
Prepare a sink with an approved cleaning solution (example: Kay-5r). USE WARM WATER AND FOLLOW
THE MANUFACTURER’S SPECIFICATIONS. If
another approved cleaner is used, dilute it according
to the label instructions. (IMPORTANT: Follow the
label directions. Too STRONG of a solution can cause
parts damage, while too MILD of a solution will not provide adequate cleaning.) Make sure all brushes provided with the freezer are available for brush cleaning.
Figure 34
Step 6
Remove the rear drip pan(s) and take to the sink for
cleaning.
Step 2
Remove the seal(s) from the drive shaft(s).
Note: If the drip pan is filled with an excessive amount
of mix, refer to the Troubleshooting Guide.
Step 3
From the freezer door(s) remove:
S
S
S
S
S
S
S
Step 7
Thoroughly brush clean all disassembled parts in the
cleaning solution making sure all lubricant and mix film
is removed. Take particular care to brush clean the
draw valve core(s) in the freezer door. Place all the
cleaned parts on a clean, dry surface to air dry
overnight.
gasket(s)
front bearing(s)
pivot pin(s)
adjustable draw handle(s)
design cap(s)
draw valve(s)
prime plug(s)
Step 8
Wipe clean all exterior surfaces of the freezer.
Remove all o-rings.
Operating Procedures
24
Models 750, 751, 754, 774, 794
Section 7
Important: Operator Checklist
During Cleaning and Sanitizing
j 7. Properly prepare the cleaning and sanitizing
solutions. Read and follow label directions
carefully. Too strong of a solution may damage
the parts and too weak of a solution will not do
an adequate job of cleaning or sanitizing.
Cleaning and sanitizing schedules are governed by
your State or local regulatory agencies and must be
followed accordingly. The following check points
should be stressed during the cleaning and sanitizing
operations.
WE RECOMMEND
SANITIZING.
DAILY
CLEANING
j 8. The temperature of the mix in the mix hopper
and walk-in cooler should be below 40_F.
(4.4_C.).
AND
Regular Maintenance Checks
ALWAYS FOLLOW LOCAL HEALTH CODES.
j 1. Replace scraper blades that are nicked or
damaged. Before installing the beater
assembly, be certain that scraper blades are
properly attached to the helix.
Troubleshooting Bacterial Count
j 1. Thoroughly clean and sanitize machine
regularly, including complete disassembly and
brush cleaning.
j 2. Check the rear shell bearing for signs of wear
(excessive mix leakage in rear drip pan) and be
certain it is properly cleaned.
j 2. Use all brushes supplied for thorough cleaning.
The brushes are specially designed to reach all
mix passageways.
j 3. Using a screwdriver and cloth towel, keep the
rear shell bearing and the female hex drive
socket clean and free of lubricant and mix
deposits.
j 3. Use the white bristle brush to clean the mix inlet
hole which extends from the mix hopper down
to the rear of the freezing cylinder.
j 4. Dispose of o-rings and seals if they are worn,
torn, or fit too loosely, and replace with new
ones.
j 4. Use the black bristle brush to thoroughly clean
the rear shell bearing located at the rear of the
freezing cylinder. Be sure to have a generous
amount of cleaning solution on the brush.
j 5. Follow all lubricating procedures as outlined in
“Assembly”.
j 5. IF LOCAL HEALTH CODES PERMIT THE
USE OF RERUN, make sure the mix rerun is
stored in a sanitized, covered stainless steel
container and used the following day. DO NOT
prime the machine with rerun. When using
rerun, skim off the foam and discard. Mix the
rerun with fresh mix in a ratio of 50/50 during the
days operation.
j 6. If your machine is air cooled, check the
condensers for accumulation of dirt and lint.
Dirty condensers will reduce the efficiency and
capacity of the machine. Condensers should be
cleaned monthly with a soft brush. Never use
screwdrivers or other metal probes to clean
between the fins.
j 6. On a designated day of the week, run the mix as
low as feasible and discard it after closing. This
will break the rerun cycle and reduce the
possibility of high bacteria and coliform counts.
Caution:
Always
disconnect
electrical power prior to cleaning the
condenser. Failure to follow this instruction
may result in electrocution.
Models 750, 751, 754, 774, 794
25
Important: Operator Checklist
Winter Storage
j 7. If your machine is equipped with an auxiliary
refrigeration system, check the auxiliary
condenser for accumulation of dirt and lint. Dirty
condensers will reduce the refrigeration
capacity of the mix hopper. Condensers must
be cleaned monthly with a soft brush. Never use
screwdrivers or other metal probes to clean
between the fins. Failure to follow this
instruction may result in electrocution.
If the place of business is to be closed during the winter
months, it is important to protect the freezer by
following certain precautions, particularly if the
building is subject to freezing conditions.
Disconnect the freezer from the main power source to
prevent possible electrical damage.
On water cooled freezers, disconnect the water
supply. Relieve pressure on the spring in the water
valve. Use air pressure on the outlet side to blow out
any water remaining in the condenser, and then add a
liberal amount of permanent type auto anti-freeze.
This is extremely important. Failure to follow this
procedure may cause severe and costly damage to the
refrigeration system.
Caution:
Always
disconnect
electrical power prior to cleaning the
condenser. Failure to follow this instruction
may result in electrocution.
j 8. If your machine is water cooled, check the water
lines for kinks or leaks. Kinks can occur when
the machine is moved back and forth for
cleaning
or
maintenance
purposes.
Deteriorated or cracked water lines should be
replaced only by an authorized Taylor
distributor.
Important: Operator Checklist
Your local Taylor Distributor can perform this winter
storage service for you.
Wrap detachable parts of the freezer such as beater,
blades, drive shaft, and freezer door, and place them
in a protected dry place. Rubber trim parts and gaskets
can be protected by wrapping them with
moisture-proof paper. All parts should be thoroughly
cleaned of dried mix or lubrication which attract mice
and other vermin.
26
Models 750, 751, 754, 774, 794
Section 8
PROBLEM
1. No product is being
dispensed with draw valve
open and the machine in
the AUTO mode.
2. The product is too stiff.
3. The product is too soft.
4. The mix in the mix hopper
is too cold.
Models 750, 751, 754, 774, 794
Troubleshooting Guide
PROBABLE CAUSE
REMEDY
PAGE
REF.
a. Freeze-up in mix inlet
hole.
a. Call service technician to
adjust the mix hopper
temperature.
b. Beater motor out on reset.
b. Reset the freezer.
c. The beater is rotating
counterclockwise from the
operator end.
c. Contact service technician
to correct rotation to
clockwise from operator
end.
------
d. The circuit breaker is off
or the fuse is blown.
d. Turn the breaker on, or
replace the fuse.
------
e. There is inadequate mix in
the mix hopper.
e. Fill the mix hopper with
mix.
22
f. The air orifice is not
installed.
f. Install air orifice in air
tube.
22
a. The viscosity needs
adjustment.
a. Contact service
technician.
b. The air orifice is not
installed.
b. Install air orifice in air
tube.
a. Viscosity needs
adjustment.
a. Contact service
technician.
b. Not enough air space
around unit. (Air cooled
units)
b. Allow for adequate air flow
across the condenser.
c. Worn scraper blades.
c. Replace regularly.
30
d. Dirty condenser (A/C)
d. Clean monthly.
25
e. Mix is out of date.
e. Use only fresh mix.
f. Loss of water. (W/C)
f. Locate cause of water
loss and correct.
a. The temperature is out of
adjustment.
a. Call service technician to
adjust the mix hopper
temperature.
27
------
14
-----22
-----1
-----26
------
Troubleshooting Guide
PROBLEM
PROBABLE CAUSE
REMEDY
5. The mix in the mix hopper
is too warm.
a. The temperature is out of
adjustment.
a. Call service technician to
adjust the mix hopper
temperature.
b. Missing or defective mix
hopper gasket.
b. Replace/install the gasket
around the mix hopper.
22
c. The mix hopper cover is
not in position.
c. Place the cover in
position.
23
d. The MIX REF light is not
lit.
d. Press the MIX REF key.
13
a. Rounded corners of drive
shaft, coupling, or both.
a. Call service technician to
correct cause, and to
replace the necessary
components. Do not
lubricate the hex end of
the drive shaft.
b. Mix and lubricant collected
in the drive coupling.
b. Brush clean the rear shell
bearing area regularly.
a. The beater assembly is
bent.
a. Call service technician to
repair or replace the
beater and to correct the
cause of insufficient mix
in the freezing cylinder.
------
b. The front bearing is
missing or worn on the
freezer door.
b. Install or replace the front
bearing.
16
a. Missing or worn drive
shaft seal on drive shaft.
a. Install or replace regularly.
15 / 30
b. The rear shell bearing is
worn.
b. Call service technician to
replace rear shell bearing.
a. Missing or worn draw
valve o-rings.
a. Install or replace regularly.
b. Inadequate lubrication of
draw valve o-rings.
b. Lubricate properly.
18
c. Wrong type of lubricant is
being used (example:
petroleum base lubricant).
c. Use the proper lubricant
(example: Taylor Lube).
15
a. Unit is unplugged.
a. Plug into wall receptacle.
------
b. The circuit breaker is off
or the fuse is blown.
b. Turn the breaker on, or
replace the fuse.
------
c. The beater motor is out on
reset.
c. Reset the freezer.
6. The drive shaft is stuck in
the drive coupling.
7. The freezing cylinder walls
are scored.
8. Excessive mix leakage
into the rear drip pan.
9. Excessive mix leakage
from door spout.
10. No freezer operation after
pressing the AUTO key.
Troubleshooting Guide
28
PAGE
REF.
------
------
24
-----18 / 30
14
Models 750, 751, 754, 774, 794
PROBLEM
PROBABLE CAUSE
11. Product is not feeding into
the freezing cylinder.
a. Inadequate level of mix in
the mix hopper.
a. Fill the mix hopper with
mix.
b. The mix inlet hole is
frozen up.
b. The mix hopper
temperature needs
adjustment. Call service
technician.
c. The air tube is installed
incorrectly.
c. Install the air tube in the
mix inlet hole, using the
end with the small hole in
the side.
22
d. The air orifice is not
installed.
d. Install the air orifice in the
air tube.
22
Models 750, 751, 754, 774, 794
29
REMEDY
PAGE
REF.
22
------
Troubleshooting Guide
Section 9
Parts Replacement Schedule
PART DESCRIPTION
EVERY
3 MONTHS
EVERY
6 MONTHS
ANNUALLY
White Bristle Brush, 3” x 7”
Inspect & Replace
if Necessary
Minimum
White Bristle Brush, 1” x 2”
Inspect & Replace
if Necessary
Minimum
Black Bristle Brush, 1” x 2”
Inspect & Replace
if Necessary
Minimum
Double-Ended Brush
Inspect & Replace
if Necessary
Minimum
Drive Shaft Seal
X
Scraper Blade
X
Freezer Door Gasket
X
Front Bearing
X
Draw Valve O-Ring
X
Pivot Pin O-Ring
X
Prime Plug O-Ring
X
Air Tube O-Ring
X
Air Orifice O-Ring
X
Refer to Parts List on page 31 when ordering the above parts.
Parts Replacement Schedule
30
Models 750, 751, 754, 774, 794
031324
028992
028991
012864
BEARING-REAR SHELL
+GUIDE-DRIP SEAL
+NUT-BRASS BEARING
+WASHER-BEARING LOCK
Models 750, 751, 754, 774, 794
025729
041575
039422
039423
BELT-AX34
BELT-AX31
BLOCK-TERMINAL-2 P
BLOCK-TERMINAL-3 P
31
053729
053726
SCREEN-BLOWER
WHEEL-BLOWER
051272
013071
013072
013073
FUSE-SLO BLO
BRUSH-BLACK (1” X 2”)
BRUSH-DOUBLE END
BRUSH-WHITE (1” X 2”)
X32326-SER
053480-27
MOTOR-BLOWER
BOARD-POWER
053727
HOUSING-BLOWER
X36641SER1
053730
CLIP-SCREEN BLOWER
BOARD-LOGIC
033047
CAPACITOR-RUN
X53478-27
BLOWER ASSEMBLY
031314
053481-27
MOTOR-BLOWER
BOOT-CAPACITOR
X53725-27
BLOWER ASSEMBLY
039420
022848
BELT-AX35
SCREW-TERMINAL BLOCK
023875
035174
BELT-AX40
+BLADE-SCRAPER
X31761
050216
BEATER ASSEMBLY
X18915
BEARING-FRONT
PART
NUMBER
ADAPTOR A.-CASTER
DESCRIPTION
1
1
1
1
1
1
2
1
1
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
1
1
1
1
1
2
1
1
2
2
1
1
1
1
1
1
4
1
1
1
2
2
2
1
1
1
1
4
1
1
1
4
2
2
4
4
2
2
2
2
2
2
4
1
1
1
2
2
2
1
1
1
1
4
1
1
1
4
2
2
4
4
2
2
2
2
2
2
4
1
1
1
2
2
2
1
1
1
1
4
1
1
1
4
2
2
4
4
2
2
2
2
2
2
4
750
751
754
774
794
QTY. QTY. QTY. QTY. QTY.
000
000
000
103
212
212
103
103
103
103
103
103
000
103
103
103
000
103
103
000
000
000
000
000
103
000
000
000
000
000
103
WARR.
CLASS
J9053627-1PH
751-PRIOR TO J9036440-3PH,
751-J9036440/UP-3PH
J9053627/UP-1PH
THREE PHASE
SINGLE PHASE
REMARKS
144
144
PARTS
UPDATE
HP62 Refrigerant: 750 - J6110454, 751 - J6080596, 754 - J6080465, 774 - J6092382, and 794 -- J4094101/up
Section 10
Parts List
+ Available Separately
Parts List
+ Available Separately
Parts List
32
Models 750, 751, 754, 774, 794
038145
RELAY-START
036047
RELAY-START
047701-27
036048
CAPACITOR-START
COMPRESSOR-AUXILIARY
048132
CAPACITOR-RUN
047519-
031790
CAPACITOR-START
COMPRESSOR - TECUMSEH
012906
CAPACITOR-RUN
052401-27
RELAY-START
048259-
031304
CAPACITOR-START
COMPRESSOR - BRISTOL
029439
CAPACITOR-RUN
052397-
COMPRESSOR- COPELAND
048765
RELAY-START
052397-33
031790
CAPACITOR-START
COMPRESSOR- COPELAND
023606
048727-
CAPACITOR-RUN
COMPRESSOR - BRISTOL
051957-27
051958-
COMPRESSOR - COPELAND
033044-1
018794
CASTER-SWIVEL
RELAY-START COMPRESSOR
019624
CAPACITOR-RUN
CAPACITOR-START
051785
CAPACITOR-RUN
012906
014218
CAP-DESIGN
CAPACITOR-RUN
042599
CABLE-RIBBON
X42513
032445
LINE A.-ACCESS COMPRESSOR
023316
CABLE-RIBBON
PART
NUMBER
BRUSH-WHITE (3” X 7”)
DESCRIPTION
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
1
1
1
750 751
QTY. QTY.
1
2
2
2
2
2
2
2
2
4
3
2
1
754
QTY.
1
2
2
2
2
1
1
1
1
4
3
2
1
774
QTY.
1
2
2
2
2
4
3
2
1
794
QTY.
512
103
103
103
512
103
103
103
512
103
103
103
512
512
103
103
103
512
103
103
103
130
512
103
103
103
000
103
103
000
WARR.
CLASS
230-60-1
230-60-1
230-60-1
751-PRIOR TO J9036440,
J9053627
774-PRIOR TO J9041932,
754-PRIOR TO J9036611
230-60-1
230-60-1
230-60-1
144
142
141
144
751-J9053627/UP-1PH
774-J9041932/UP
141
142
144
112/136
136
136
136
136
PARTS
UPDATE
754-J9036611/UP
751-J9036440/UP-3PH
230-60-1
230-60-1
230-60-1
PRIOR TO J8108583
230-60-1
230-60-1
230-60-1
COPELAND
J8108583/UP
FAN MOTOR - 041401-27
FAN MOTOR - 051744-27
REMARKS
+ Available Separately
Models 750, 751, 754, 774, 794
33
Parts List
046585048199X51531-10
DIAGRAM-WIRING
DIAGRAM-WIRING
DOOR A.-FREEZER
050216
014218
021521
048926
+CAP-DESIGN
DECAL-DOOR
+GASKET-DOOR
X51532-12
+BEARING-FRONT
DOOR A.-FREEZER
048926
050318-
DIAGRAM-WIRING (OLD)
+GASKET-DOOR
052613-
DIAGRAM-WIRING (NEW)
014218
047912
DEFLECTOR-BLOWER EXHAUST
+CAP-DESIGN
046586
DEFLECTOR-BLOWER EXHAUST
050216
038374
DECAL-TROUBLESHOOTING
+BEARING-FRONT
032484
DECAL-POWER SWITCH - ON/OFF
036551
DECAL-HEATER SWITCH
032484
045812
DECAL-DECORATIVE SOFTECH
DECAL-POWER SWITCH - ON/OFF (OLD)
032919
DECAL-DECORATIVE SOFTECH
019029
033230
DECAL-DECORATIVE SOFTECH
DECAL-CLEAN & SANITIZE
041682-GRY
COVER-MIX HOPPER
025429
X38458-SER
COVER A.-MIX HOPPER
KNOB-MIX HOPPER
012721
COUPLING-DRIVE
038474
048233
CONDENSER-MAIN
+GASKET-MIX HOPPER
046558
CONDENSER-MAIN
038375
027155
CONDENSER-AUXILIARY
+GASKET-MIX HOPPER
047739
047702-27
COVER-TERMINAL
047703
RELAY-START
PART
NUMBER
CAPACITOR-START
DESCRIPTION
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
750 751
QTY. QTY.
2
1
3
2
1
1
1
1
1
1
1
2
1
2
2
2
1
1
1
1
754
QTY.
2
1
3
2
1
1
1
1
1
1
1
1
2
1
2
2
2
1
1
1
1
774
QTY.
2
1
3
2
1
1
1
1
1
1
1
2
2
2
1
1
1
1
794
QTY.
000
000
000
000
103
000
000
000
103
000
000
000
000
103
103
000
000
000
000
000
000
000
000
103
103
000
000
103
103
103
103
103
103
103
103
WARR.
CLASS
PRIOR TO COPELAND
W/COPELAND
PRIOR TO J8080000 (NEW SEE LABEL)
“ON-OFF”
REMARKS
136/144
136/144
132
PARTS
UPDATE
+ Available Separately
Parts List
34
Models 750, 751, 754, 774, 794
X28699
X45691
X26996
GUIDE A.-DRIP PAN
GUIDE A.-DRIP PAN
HANDLE A.-ADJUSTABLE DRAW
014402
016272
016137
032560
048260-WHT
O-RING
O-RING
O-RING
SEAL
TOOL-O-RING REMOVAL
050216
014218
048926
018572
BEARING-FRONT
CAP-DESIGN
GASKET-DOOR
O-RING
X49463-4
018572
O-RING
KIT A.-TUNE-UP
048926
GASKET-DOOR
014218
X49463-11
KIT A.-TUNE-UP
CAP-DESIGN
036574
JAR-STAINLESS SYRUP
050216
036573
JAR-PLASTIC SYRUP
BEARING-FRONT
035434
HOOD
015872
O-RING
X35565
033662
HOOD ASSEMBLY
028804
SCREW-ADJUSTABLE
X33687
HANDLE-DRAW
HANDLE A.-ADJUSTABLE DRAW
015872
X28863
GUIDE A.-DRIP PAN
O-RING
X50752
GUIDE A.-DRIP PAN
026592
021286-SER
GEAR-REDUCER
SCREW-ADJUSTABLE
048926
GASKET-FREEZER DOOR
028804
048901
HANDLE-DRAW
047699
DRYER-FILTER
PART
NUMBER
DRYER-CAPILLARY
DESCRIPTION
1
1
3
1
2
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
3
1
2
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
750 751
QTY. QTY.
8
2
3
2
1
1
3
3
3
3
1
2
2
2
1
754
QTY.
8
2
3
2
1
2
2
1
3
3
3
3
1
2
2
2
1
774
QTY.
8
2
3
2
1
3
3
3
3
1
2
2
2
1
794
QTY.
000
000
000
000
000
000
000
000
000
000
000
000
000
000
000
103
103
103
103
000
103
103
103
000
000
103
103
103
103
103
103
212
000
000
000
WARR.
CLASS
AIR TUBE
DRIVE SHAFT
PRIME PLUG & AIR ORIFICE
PIVOT PIN
DRAW VALVE
AIR TUBE
STAINLESS
J7090000/UP (REPLACES
X26996)
PLASTIC
AUXILIARY
REMARKS
121
121
PARTS
UPDATE
+ Available Separately
Models 750, 751, 754, 774, 794
35
Parts List
013458
036575
013631
017471
047518
028754-M
LEG (4” w/O-RING)
LID-W/LADLE
LOUVER-SIDE (LEFT)
LOUVER-SIDE
LUBRICANT-TAYLOR 4 OZ.
MAN-OPER
034382
034383
NUT-STUD (LONG)
NUT-STUD (SHORT)
023348
013163
PAIL
016137
PAIL
O-RING
022465-100
021508
NUT-STUD (HANDSCREW)
ORIFICE-AIR
029639-BLK
033499
027309-
047279
NUT-JAM-5/16-24
+BLADE-FAN
MOTOR-FAN (w/BLADE)
+BLADE-FAN (12” PUSH)
041401-27
045862
CAPACITOR-START (230-60-1)
MOTOR-FAN (CONDENSER)
028315
CAPACITOR-START (230-60-1)
051744-27
036084
CAPACITOR-RUN (230-60-1)
MOTOR-FAN (CONDENSER)
027087
CAPACITOR-RUN (230-60-1)
021522-
051433
LABEL-WARN-COVER
MOTOR-BEATER
052632
048260-WHT
TOOL-O-RING REMOVAL
036693
034698
SEAL-DRAW VALVE
LABEL-SWITCH-POWER-OFF/ON SYMBOLS
032560
SEAL
LABEL-FLAVOR
016137
O-RING
032749
016272
LABEL-DOOR-WARN-MOVE PARTS
014402
O-RING
PART
NUMBER
O-RING
DESCRIPTION
1
1
1
4
1
1
1
1
1
1
1
1
1
1
1
1
1
4
4
1
1
1
1
4
1
1
1
1
1
1
1
1
1
2
5
1
750 751
QTY. QTY.
1
2
2
2
2
3
1
1
2
2
2
2
2
1
1
2
6
1
1
1
1
2
6
1
5
754
QTY.
1
2
2
2
2
3
1
1
2
2
2
2
2
1
1
2
2
7
1
1
1
1
2
6
1
5
774
QTY.
1
2
2
2
2
3
1
1
2
2
2
2
2
1
1
2
5
1
1
1
1
1
2
6
1
5
794
QTY.
000
000
000
103
103
103
103
000
103
103
103
103
103
103
103
103
103
212
000
000
103
103
103
103
000
000
000
000
000
000
000
000
000
000
WARR.
CLASS
10 QT. / 9.5 LITER
6 QT. / 5.7 LITER
SHORT
LONG
HANDSCREW
J7090000/UP
SHR
SHR
PRIOR TO J8108583
J8108583/UP (COPELAND)
LEESON 230-30-1
MAGNETEK/CENTURY
230-30-1
LEESON 230-30-1
MAGNETEK/CENTURY
230-30-1
LEFT
ON POSITION - RIGHT SIDE
J9036300/UP
H-RING
DRIVE SHAFT
PRIME PLUG & AIR ORIFICE
PIVOT PIN
DRAW VALVE
REMARKS
121
136
136
132/142
PARTS
UPDATE
+ Available Separately
Parts List
36
Models 750, 751, 754, 774, 794
023953-5
016369
049993
049992
O-RING
THERMOSTAT-ADJUSTABLE
THERMOSTAT-HI LIMIT
X42539
PANEL A.-FRONT
PLUG-DRAIN
X32956
PANEL A.-FRONT
030994
X33237
PANEL A.-FRONT
LABEL-TEMPERATURE ADJUSTMENT
X50754
PANEL A.-FRONT
023953-4
X46448-SER
PANEL A.-LOWER SIDE-RIGHT
HEATER-STRIP
X46447-SER
042317
PANEL-UPPER RIGHT SIDE
PANEL A.-LOWER SIDE-LEFT
041856
PANEL-SERVICE
028822
047077
PANEL-SERVICE
PANEL-UPPER SIDE-LEFT
046584
PANEL-SERVICE
024426
047170
PANEL-SERVICE
PANEL-UPPER SIDE
X42574
PANEL A.-REAR-UPPER
X39075-SER
042577
PANEL-REAR-LOWER
PANEL A.-LOWER SIDE-LOUVERED-LEFT
041855
PANEL-REAR
050741
017563
PANEL-REAR
PANEL-LEFT SIDE
013637
PANEL-REAR
X24424-SER
020891
PANEL-REAR
PANEL-LOWER RIGHT SIDE
X41844
PAN A.-HINGED DRIP
028823
035034
PAN-DRIP
PANEL-UPPER RIGHT SIDE
027504
PAN-DRIP 17-1/4” LONG
050742
027503
PANEL-RIGHT SIDE
050766
PAN-DRIP - 11-5/8” LONG
PART
NUMBER
PAN-DRIP
DESCRIPTION
1
1
1
1
1
1
1
1
1
1
1
1
1
1
750 751
QTY. QTY.
1
1
1
1
1
1
1
1
754
QTY.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
774
QTY.
1
1
2
1
1
1
1
794
QTY.
103
103
000
103
000
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
WARR.
CLASS
REMARKS
PARTS
UPDATE
+ Available Separately
Models 750, 751, 754, 774, 794
37
Parts List
X30922
PROBE A.-MIX
048149
048148
035514
051065
032758
032762016369
036822
036577
036821
036578
X33057
019330
032761
O-RING-1” OD
COLLAR-GAGING-1/202
CYLINDER-SYRUP PUMP
INSERT-PLUNGER
KNOB-PLUNGER (w/O-RING)
+O-RING
LID-PUMP
NUT-PLUNGER
NUT-SPOUT
PLUNGER
SEAL ASSEMBLY (w/O-RING)
+O-RING
SPRING-PLUNGER
053794-TAN
PUMP A.-SYRUP TAN CAPTIVE BALL
048166-001
027822
PULLEY (GEAR)
O-RING-1-5/16 OD
016403
PULLEY (BEATER MOTOR)
KIT-VALVE-CAPTURED BALL SHALL0W
X31602
X34466
PROBE A.-THERMISTOR - HOPPER
PROBE A.-THERMISTOR - BARREL
X50717
PROBE A.-THERMISTOR - HOPPER
030966
016137
+O-RING
+SPACER
028805
PLUG-PRIME
030965
029595
PLUG-DRIP TRAY HOLE
+DISC
041854
PLATE-DECORATIVE
016272
+O-RING
032961
X20683
PIN A.-PIVOT
PLATE-DECORATIVE
016272
+O-RING
033239
X22820
PLATE-DECORATIVE
X41820
PIN A.-PIVOT
PART
NUMBER
PANEL A.-FRONT
DESCRIPTION
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
750 751
QTY. QTY.
2
2
2
1
2
2
2
4
2
1
1
1
1
754
QTY.
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
1
2
2
2
4
2
1
1
1
1
774
QTY.
2
2
2
1
1
2
2
2
4
2
1
1
1
1
794
QTY.
000
000
103
103
103
103
103
000
103
103
103
103
000
000
103
103
103
103
103
103
103
103
103
103
000
103
000
103
103
103
000
103
000
103
103
WARR.
CLASS
032762-BRN - 032762-TAN
GEAR
BEATER MOTOR
PRIOR TO J8110000
794 - J8110000/UP
REMARKS
136
136
PARTS
UPDATE
+ Available Separately
Parts List
38
Models 750, 751, 754, 774, 794
041950047150-
STARTER-BEATER LINE
024295
037394
051974
SWITCH-TOGGLE (POWER SWITCH)
SWITCH-TOGGLE (POWER SWITCH)
SWITCH-TOGGLE (HEATER SWITCH)
X33326
X43722
049178
015478
041660
041661
028889
BRACKET A.-SWITCH
E-RING
PIN-PIVOT
SPRING-LEFT RETURN
SPRING-RIGHT RETURN
SWITCH-MICRO
X33322-SER
SWITCH A.-DRAW
ARM A.-SWITCH
012626
SWITCH-TOGGLE (HEATER SWITCH)
052183-SYM
048230
SWITCH-PRESSURE 440 PSI (A/C)
+ LABEL-SWITCH HEATER
052663
SWITCH-PRESSURE 405 PSI (A/C) - NEW
1
1
1
1
1
1
1
1
1
1
1
1
022765
SHIELD-SPLASH
OVERLOAD-THERMAL
1
022766
1
022763
SHIELD-SPLASH
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
1
1
1
1
1
1
750 751
QTY. QTY.
SHIELD-SPLASH
022822
X41786
SHELL A.-INSULATED
+STUD-NOSE CONE
X51711
032560
+SEAL-DRIVE SHAFT
SHELL A.-INSULATED
032564
SHAFT-BEATER DRIVE
X50327
041082
SANITIZER-KAY-5
SHELL A.-INSULATED
032607-
RELAY-SPDT-30A-240V (A/C)
X49785
012725-
RELAY-COMPRESSOR
SHELL A.-INSULATED
032760
WASHER-NYLON
X50745
032757
SHELL A.-INSULATED
050912
TUBE-PLUNGER
PART
NUMBER
TUBE-DISCHARGE
DESCRIPTION
1
2
2
2
1
4
1
2
2
1
1
2
754
QTY.
1
1
1
1
2
2
2
2
1
4
1
2
2
1
1
2
2
2
2
774
QTY.
1
2
2
2
1
4
1
1
2
2
1
1
2
794
QTY.
103
103
103
103
000
103
103
103
103
000
103
103
103
103
103
103
103
103
103
103
103
512
512
512
512
512
000
103
000
103
103
000
103
103
WARR.
CLASS
PRIOR TO J9041932
J9041932/UP
J9041932/UP
BRISTOL
COPELAND
PRIOR TO J8110000
J8110000/UP
FOR BLOWER-X47833-27
*750-FOR FAN MOTOR
041401-27
REMARKS
142
142
142
136/142
136/142
136
136
136
PARTS
UPDATE
+ Available Separately
Models 750, 751, 754, 774, 794
39
Parts List
038484
038254
038922
038923
038924
X39269
PIN-PIVOT
ROD-SPRING RETAINER
SPRING-EXTENSION
SPRING-LEFT RETURN
SPRING-RIGHT RETURN
SWITCH A.-DRAW
050900
+BOOT-EXPANSION VALVE
022665
046365
VALVE-AUTOMATIC EXPANSION
VALVE-E.P.R.
029406
044404
VALVE-ACCESS
043232
X29429-2
TUBE A.-AIR
VALVE-ACCESS
041853
TRIM-RIGHT REAR CORNER
VALVE-ACCESS
013663
TRIM-RIGHT REAR CORNER
044455
020883
TRIM-RIGHT REAR CORNER
VALVE-ACCESS
020677
TRIM-RIGHT REAR CORNER
047016
041852
TRIM-LEFT REAR CORNER
VALVE-ACCESS
013761
TRIM-LEFT REAR CORNER
018572
020882
TRIM-LEFT REAR CORNER
+O-RING
020678
TRIM-LEFT REAR CORNER
020157
TRAY-FRONT DRIP
020889
014533
TRAY-FRONT DRIP
TRIM-FRONT
013690
TRAY-FRONT DRIP
039252
032190
E-RING
SWITCH-MICR+A321O
X38252
BRACKET A.-SWITCH
039264
038650
ARM-SWITCH-RIGHT
BRACKET-SWITCH
038649
X38547
PART
NUMBER
ARM-SWITCH-LEFT
SWITCH A.-DRAW
DESCRIPTION
1
1
1
1
1
2
4
1
1
1
1
1
1
1
1
1
1
1
1
1
4
1
1
1
1
750 751
QTY. QTY.
1
2
2
1
1
2
2
8
2
1
1
1
2
1
1
1
1
2
1
1
4
1
1
1
1
754
QTY.
1
2
2
1
1
2
2
8
2
1
1
1
2
1
1
1
1
2
1
1
4
1
1
1
1
774
QTY.
1
2
2
1
1
2
2
8
2
1
1
1
2
1
1
1
1
2
1
1
4
1
1
1
1
794
QTY.
103
000
103
103
103
103
103
103
000
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
000
103
103
103
103
WARR.
CLASS
750 W/BRISTOL
COMPRESSOR
REMARKS
136
PARTS
UPDATE
+ Available Separately
Parts List
40
Models 750, 751, 754, 774, 794
015184-
MOTOR-FAN
048231
046686
SWITCH-PRESSURE
VALVE-WATER
028315
026659
051958-
CAPACITOR-START (BEATER MOTOR)
CAPACITOR-START (BEATER MOTOR)
COMPRESSOR-COPELAND
027087
031790
048766
CAPACITOR-START (230-50-1)
RELAY-START (230-50-1)
048727-
CAPACITOR-RUN (230-50-1)
COMPRESSOR (MAIN - HP62) -BRISTOL
051957-40
023739
CAPACITOR-RUN (BEATER MOTOR)
RELAY-START COMPRESSOR
023606
CAPACITOR-RUN (BEATER MOTOR)
051960
039424
BLOCK-TERMINAL (220/440-50-3)
CAPACITOR-START
039421
BLOCK-TERMINAL (230-50-1)
023606
032769
BELT-AX32
CAPACITOR-RUN
022848
BELT-AX35
50 CYCLE
X24424-SER
PANEL A.-LOWER SIDE (R & L)
013043
048287
CONDENSER
+BLADE-FAN (10” PUSH)
049309
022505
012796-
CONDENSER
+GUARD-BLOWER
BLOWER
WATER COOLED
OPTIONAL FEATURES
038047-
014402
VIDEO-TRAINING FILM
X18303
+O-RING
PART
NUMBER
VALVE A.-DRAW
DESCRIPTION
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
2
1
1
1
1
2
1
750 751
QTY. QTY.
2
2
2
2
2
2
2
2
2
2
1
1
1
6
3
754
QTY.
2
2
2
2
2
4
2
2
2
2
1
1
1
6
3
774
QTY.
2
2
2
2
2
4
2
2
2
1
1
1
6
3
794
QTY.
103
103
103
512
103
103
103
512
103
103
103
103
103
103
000
000
103
103
103
103
103
103
103
103
103
000
000
103
WARR.
CLASS
PRIOR TO J8108583
230-50-1
230-50-1
230-50-1
J8108583/UP
LEESON
CENTURY/MAGNETEK
LEESON
CENTURY/MAGNETEK
J7060000 (REPLACES X45380)
REMARKS
136
136
136
136
136
118
PARTS
UPDATE
+ Available Separately
Models 750, 751, 754, 774, 794
41
Parts List
038146
RELAY-START
036048
036047
CAPACITOR-START
RELAY-START
1
047279
011545
BLADE-FAN (12” PUSH)
PULLEY (BEATER MOTOR)
1
1
047178-34
MOTOR-FAN
029439
CAPACITOR-RUN
047519-
031790
CAPACITOR-START
COMPRESSOR-MAIN (HP62)-TECUMSEH
023739
CAPACITOR-RUN
1
1
1
1
1
1
048259-
052401-27
COMPRESSOR (MAIN - HP62) BRISTOL
RELAY-START COMPRESSOR
1
052399
1
052400
1
750 751
QTY. QTY.
CAPACITOR-START-145-175UF/250V
052397-
PART
NUMBER
CAPACITOR-RUN- 45UF/370V
COMPRESSOR-COPELAND
DESCRIPTION
2
2
2
2
2
2
2
2
2
754
QTY.
2
2
2
2
2
2
774
QTY.
2
2
2
2
2
794
QTY.
103
103
103
103
103
103
512
103
103
103
512
103
103
103
512
WARR.
CLASS
141
142
141
142
754-PRIOR TO J9036611
774-PRIOR TO J9041932
230-50-1
230-50-1
230-50-1
230-50-1
230-50-1
230-50-1
144
751-PRIOR TO J9053634
230-50-1
230-50-1
144
754-J9036611/UP
774-J9041932/UP
230-50-1
PARTS
UPDATE
751-J9053634/UP
REMARKS
Models 750 & 751
052613-27
Rev. 10/02
Models 750 & 751
052613-33
Rev. 10/02
Models 750 & 751
052613-40
Rev. 10/02
Models 750 & 751
052613-58
Rev. 10/02
Models 754 & 774
046585--27
Rev. 10/02
Models 754 & 774
046585--33
Rev. 10/02
Model 794
048199--27
Rev. 10/02
Model 794
048199--33
Rev. 10/02
Model 794
048199--62
Rev. 10/02