Axor 18113181 Plumbing Product User Manual

Installation Instructions / Warranty
Talis
32040XX1
32240XX1
Talis Lavatory Faucet 32040XX1
Talis Bidet Faucet 32240XX1
32040XX1
32240XX1
Technical Data
Maximum flow rate
2.2 gpm
Operating pressure: max. 145 psi
Recommended operating pressure: 14.5 - 72 psi
Test pressure:
232 psi
Hot water temperature:
max. 176° F*
Recommended hot water temp.: 120° - 140° F*
Hole size in mounting surface 1 1/4”
Max. mounting surface depth: 1 5/8”
3/8” supply hoses require stops with 3/8” compression
fittings (not included)
The bidet faucet is not for use on a bidet with a vertical spray.
*Please know and follow all applicable local plumbing codes
when setting the temperature on the water heater.
Caution:
Do not bend or twist
the supply hoses!
Installation
Flush the hot and cold supplies thoroughly before
installing the faucet!
Place the faucet and sealing washer on the mounting surface.
If the mounting surface is less than 3/16” thick,
trim the sealing washer so that it is even with the
bottom of the mounting surface.
From beneath the mounting surface, install the slide
washer and collar nut. Tighten the collar nut by
hand.
slide washer
collar nut
Use 3/8” compression fittings (not included) to connect the supply hoses to the hot and cold stops. Use
two wrenches, as shown in the diagram, to prevent
hose twisting.
For proper operation of the faucet, the hot supply
should be on the left, and the cold supply should be on
the right.
Install the pop-up drain and pull rod.
Turn on the water and check all connections for leaks.
If desired, re-set the high temperature limit stop.
Install the Pop-up Drain
plunger
Remove the plunger assembly.
height adjuster
Unscrew the drain outlet flange from the
tee.
flange
Unscrew the tailpiece from the tee. Wrap
the threads with plumbers’ thread tape and
replace.
Install the white, flexible sealing gasket to
the flange. Place it in the sink outlet.
From under the sink, install the black mack
gasket, white friction ring and retainer nut
to the flange. Do not tighten the nut against
the bottom of the sink at this time.
Thread the tee and tailpiece to the flange.
The pivot must face the faucet. If necessary, turn the drain assembly.
Tighten the retainer nut.
sealing gasket
pull rod
mack gasket
friction ring
retainer nut
tee
pivot ball nut
Place the plunger assembly in the drain.
Install the horizontal rod so that the end
goes through the loop in the bottom of the
height adjuster.
Install and hand tighten the pivot ball nut.
tailpiece
horizontal rod
swivel connector
Attach the swivel connector to the end of the horizontal rod.
Attach the swivel connector to the end of the pull rod. Position as desired and tighten with a
small, flathead screwdriver.
Re-set the High Temperature Limit Stop (optional)
Close the drain or cover it with a wash cloth.
Use a 4 mm Allen wrench to push the screw
cover into the handle. Retrieve the screw cover
when the handle is removed.
Use the 4mm Allen wrench to loosen the handle
screw 4 complete revolutions. Remove the
handle and put it in a safe place.
Remove the decorative nut cover and put it in a
safe place.
Remove the handle screw from the stem of the
cartridge. Remove the high temperature limit
stop.
Replace the high temperature limit stop so that
the pin on the cartridge is in the desired slot on
the limit stop. Note: the temperatures given in
the diagram assume a water heater temperature
of 140o F, a cold water temperature of 50o F
and a water pressure of 45 PSI.
Replace the decorative nut cover. Replace the handle screw. Use the Allen wrench to turn the
screw 4 revolutions.
Replace the handle. Finish tightening the handle screw. Turn on the water and test the faucet.
User Instructions
Pivot the handle up to turn the water on, down to turn the water off. Pivot the handle to the left for
warmer water, to the right for colder water.
Replacement Parts
2
3
4
1
10
6
5
1 handle
1.1 screw cover
2 flange
3 nut
4 cartridge cpl.
5 seal
6 aerator cpl.
7 fixing set
8 connection hose
9 pull rod
10 ball joint
9
6
7
8
1.1
32096000
96338000
97406000
97209000
92730000
95008000
13912000
96016000
96321001
96657000
92036000
Cleaning Recommendation for Hansgrohe Products
Modern faucetry and shower products utilize a combination of materials to comply with the needs of the
market with regard to design and functionality.
To avoid damage, it is necessary to use some caution when cleaning. Damage caused by improper treatment
is not covered under the Hansgrohe warranty.
Cleaning Materials for Faucets and Showers
•
•
•
•
To remove lime scale, use only products made specifically for that purpose. Always follow the
manufacturer’s instructions when using.
Do not use cleaners that contain hydrochloric, formic, acetic, or phosphoric acids, as these will cause
considerable damage to finishes and to plastic components.
Never mix cleaning materials.
Never use cleaners containing abrasives. Do not use abrasive cleaning cloths, pads, or sponges.
Cleaning Procedures
•
•
•
•
Clean your faucets and shower products as and when required. Regular cleaning will prevent scale
buildup and water spotting.
Follow the label instructions. Do not allow any cleaner to remain on the product for longer than
necessary.
When using spray cleaners, spray first onto a sponge or cloth – do not spray directly onto the product.
After cleaning, rinse thoroughly with clear water to remove any cleaner residue.
Important
• Soap and shampoo residue can also cause damage to the product. Rinse well with clean water after use.
• If the surface is already damaged, harsh cleaning materials will cause further damage.
Limited Lifetime Consumer Warranty
This product has been manufactured and tested to the highest quality standards by Hansgrohe, Inc. (“Hansgrohe”). This warranty is limited to
Hansgrohe products which are purchased by a consumer in the United States after March 1, 1996, and installed in either the United States or
Canada.
WHO IS COVERED BY THE WARRANTY
This warranty extends to the original consumer purchaser only. This warranty is non-transferable.
WHAT IS COVERED BY THE WARRANTY
This warranty covers only your Hansgrohe manufactured product. Hansgrohe warrants this product against defects in material or workmanship
as follows: Hansgrohe will repair at no charge for parts only or, at its option, replace any product or part of the product that proves defective
because of improper workmanship and/or material, under normal installation, use, service and maintenance. If Hansgrohe is unable to provide a
replacement and repair is not practical or cannot be timely made, Hansgrohe may elect to refund the purchase price in exchange for the return of
the product.
LENGTH OF WARRANTY
Replacement or repaired parts of products will be covered for the term of this warranty as stated in the following two sentences. If you are a
consumer who purchased the product for use primarily for personal, family, or household purposes, this warranty extends for as long as you
own the product and the home in which the product is originally installed. If you purchased the product for use primarily for any other purpose,
including, without limitation, a commercial purpose, this warranty extends only (i) for 1 year, with respect to Hansgrohe and Commercial products,
and (ii) for 5 years, with respect to AXOR products.
THIS WARRANTY DOES NOT COVER, AND HANSGROHE WILL NOT PAY FOR:
A.
Conditions, malfunctions or damage not resulting from defects in material or workmanship.
B.
Conditions, malfunctions or damage resulting from (1) normal wear and tear, improper installation, improper maintenance, misuse, abuse,
negligence, accident or alteration, or (2) the use of abrasive or caustic cleaning agents or “no-rinse” cleaning products, or the use of the
product in any manner contrary to the product instructions. (3) Conditions in the home such as excessive water pressure or corrosion.
C.
Labor or other expenses for the disconnection, deinstallation, or return of the product for warranty service, or for installation or reinstallation
of the product (including but not limited to proper packaging and shipping costs), or for installation or reinstallation of the product.
D.
Accessories, connected materials and products, or related products not manufactured by Hansgrohe.
TO OBTAIN WARRANTY PARTS OR INFORMATION
Contact your Hansgrohe retailer, or contact Technical Service at:
Hansgrohe Inc.
1492 Bluegrass Lakes Parkway
Alpharetta GA 30004
Toll-free (800) 334-0455.
In requesting warranty service, you will need to provide
1.
2.
3.
The sales receipt or other evidence of the date and place of purchase.
A description of the problem.
Delivery of the product or the defective part, postage prepaid and carefully packed and insured, to Hansgrohe Inc. 1492 Bluegrass Lakes
Parkway, Alpharetta, Georgia 30004, Attention: Technical Service, if required by Hansgrohe.
When warranty service is completed, any repaired or replacement product or part will be returned to you postage prepaid.
EXCLUSIONS AND LIMITATIONS
REPAIR OR REPLACEMENT (OR, IN LIMITED CIRCUMSTANCES, REFUND OF THE PURCHASE PRICE) AS PROVIDED UNDER THIS WARRANTY IS
THE EXCLUSIVE REMEDY OF THE PURCHASER. HANSGROHE NEITHER ASSUMES NOR AUTHORIZES ANY PERSON TO CREATE FOR IT ANY
OBLIGATION OR LIABILITY IN CONNECTION WITH THIS PRODUCT.
HANSGROHE SHALL NOT BE LIABLE TO PURCHASER OR ANY PERSON FOR ANY INCIDENTAL, SPECIAL, OR CONSEQUENTIAL DAMAGES,
ARISING OUT OF BREACH OF THIS WARRANTY OR ANY IMPLIED WARRANTY (INCLUDING MERCHANTABILITY).
PRODUCT INSTRUCTIONS AND QUESTIONS
Upon purchase or prior to installation, please carefully inspect your Hansgrohe product for any damage or visible defect. Prior to installing,
always carefully study the enclosed instructions on the proper installation and the care and maintenance of the product. If you have questions at
any time about the use, installation, or performance of your Hansgrohe product, or this warranty, please call or write to us or call us toll-free at
800 334 0455.
Hansgrohe, Inc. • 1490 Bluegrass Lakes Parkway • Alpharetta, GA 30004
Tel. 770 360-9880 • Fax 770 360 9887
www.hansgrohe-USA.com
US - Installation Instructions • Part No. 90571921 • Revised 01/2007
Some States do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply
to you. This warranty gives you specific legal rights, and you may have other rights which vary from State to State. You may be required by law
to give us a reasonable opportunity to correct or cure any failure to comply before you can bring any action in court against us under the
Magnuson-Moss Warranty Act.
Download PDF

advertising