Owner`s manual | Barco G500 Projector User Manual

iQ PRO G500
Owner’s Manual
R9003081
R5976491/09
01/02/2007
Product revision
Software version: projector firmware V3.10
Software version: Server version 1.20
Software version: Client version 1.20
Barco nv Presentations
Noordlaan 5, 8520 Kuurne
Phone: +32 56.36.82.11
Fax: +32 56.35.86.51
E-mail: presentations.bid@barco.com
Visit us at the web: www.barco.com
Printed in Belgium
Federal Communications Commission (FCC Statement)
This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area may
cause harmful interference, in which case the user will be responsible for correcting any interference.
End User License agreement (EULA)
You have acquired a device that includes software licensed by Barco from Microsoft Licensing Inc. or its affiliates (“MS”). Those installed
software products of MS origin, as well as associated media, printed materials, and “online” or electronic documentation (“SOFTWARE”)
are protected by international intellectual property laws and treaties. The SOFTWARE is licensed, not sold. All rights reserved.
IF YOU DO NOT AGREE TO THIS END USER LICENSE AGREEMENT (“EULA”), DO NOT USE THE DEVICE OR COPY THE SOFTWARE. INSTEAD, PROMPTLY CONTACT BARCO FOR INSTRUCTIONS ON RETURN OF THE UNUSED DEVICE(S) FOR A REFUND.
ANY USE OF THE SOFTWARE, INCLUDING BUT NOT LIMITED TO USE ON THE DEVICE, WILL CONSTITUTE YOUR AGREEMENT
TO THIS EULA (OR RATIFICATION OF ANY PREVIOUS CONSENT).
This EULA grants you the following license:
•
You may use the SOFTWARE only on the DEVICE
•
NOT FAULT TOLERANT: THE SOFTWARE IS NOT FAULT TOLERANT. BARCO HAS INDEPENDENTLY DETERMINED HOW TO
USE THE SOFTWARE IN THE DEVICE, AND MS HAS RELIED UPON BARCO TO CONDUCT SUFFICIENT TESTING TO DETERMINE THAT THE SOFTWARE IS SUITABLE FOR SUCH USE
•
NO WARRANTIES FOR THE SOFTWARE: THE SOFTWARE is provided “AS IS” and with all faults. THE ENTIRE RISK AS TO
SATISFACTORY QUALITY, PERFORMANCE, ACCURACY, AND EFFORT (INCLUDING LACK OF NEGLIGENCE) IS WITH YOU.
ALSO, THERE IS NO WARRANTY AGAINST INTERFERENCE WITH YOUR ENJOYMENT OF THE SOFTWARE OR AGAINST
INFRINGEMENT. IF YOU HAVE RECEIVED ANY WARRANTIES REGARDING THE DEVICE OR THE SOFTWARE, THOSE WARRANTIES DO NOT ORIGINATE FROM, AND ARE NOT BINDING ON, MS.
•
No Liability for Certain Damages: EXCEPT AS PROHIBITED BY LAW, MS AND BARCO SHALL HAVE NO LIABILITY FOR ANY
INDIRECT, SPECIAL, CONSEQUENTIAL OR INCIDENTAL DAMAGES ARISING FROM OR IN CONNECTION WITH THE USE
OR PERFORMANCE OF THE SOFTWARE. THIS LIMITATION SHALL APPLY EVEN IF ANY REMEDY FAILS OF ITS ESSENTIAL
PURPOSE. IN NO EVENT MS AND BARCO SHALL BE LIABLE FOR ANY AMOUNT IN EXCESS OF U.S. TWO HUNDRED FIFTY
DOLLARS (U.S.$250.00).
•
Limitations on Reverse Engineering, Decompilation, and Disassembly: You may not reverse engineer, decompile, or disassemble the SOFTWARE, except and only to the extent that such activity is expressly permitted by applicable law notwithstanding this
limitation.
•
SOFTWARE TRANSFER ALLOWED BUT WITH RESTRICTIONS: You may permanently transfer rights under this EULA only as
part of a permanent sale or transfer of the Device, and only if the recipient agrees to this EULA. If the SOFTWARE is an upgrade, any
transfer must also include all prior versions of the SOFTWARE.
•
EXPORT RESTRICTIONS: You acknowledge that SOFTWARE is of US-origin. You agree to comply with all applicable international
and national laws that apply to the SOFTWARE, including the U.S. Export Administration Regulations, as well as end-user, end-use
and country destination restrictions issued by U.S. and other governments. For additional information on exporting the SOFTWARE,
see http://www.microsoft.com/exporting/.
•
Installation and Use: The SOFTWARE may not be used by more than two (2) processors at any one time on the DEVICE. You
may permit a maximum of ten (10) computers or other electronic devices (each a “Client”) to connect to the DEVICE to utilize the
services of the SOFTWARE solely for file and print services, internet information services, and remote access (including connection
sharing and telephony services). The ten (10) connection maximum includes any indirect connections made through “multiplexing”
or other software or hardware which pools or aggregates connections. Except as otherwise permitted in the NetMeeting/Remote
Assistance/Remote Desktop Features terms below, you may not use a Client to use, access, display or run the SOFTWARE, the
SOFTWARE’s user interface or other executable software residing on the DEVICE.
•
If you use the DEVICE to access or utilize the services or functionality of Microsoft Windows Server products (such as Microsoft
Windows NT Server 4.0 (all editions) or Microsoft Windows 2000 Server (all editions)), or use the DEVICE to permit workstation or
computing devices to access or utilize the services or functionality of Microsoft Windows Server products, you may be required to
obtain a Client Access License for the Device and/or each such workstation or computing device. Please refer to the end user license
agreement for your Microsoft Windows Server product for additional information.
•
Restricted Uses: The SOFTWARE is not designed or intended for use or resale in hazardous environments requiring fail-safe performance, such as in the operation of nuclear facilities, aircraft navigation or communication systems, air traffic control, or other devices
or systems in which a malfunction of the SOFTWARE would result in foreseeable risk of injury or death to the operator of the device
or system, or to others.
•
Restricted Functionality: You are licensed to use the SOFTWARE to provide only the limited functionality (specific tasks or processes) for which the DEVICE has been designed and marketed by BARCO. This license specifically prohibits any other use of the
software programs or functions, or inclusion of additional software programs or functions, on the DEVICE.
•
Security Updates: Content providers are using the digital rights management technology (“Microsoft DRM”) contained in this SOFTWARE to protect the integrity of their content (“Secure Content”) so that their intellectual property, including copyright, in such content
is not misappropriated. Owners of such Secure Content (“Secure Content Owners”) may, from time to time, request MS, Microsoft
Corporation or their subsidiaries to provide security related updates to the Microsoft DRM components of the SOFTWARE (“Security
Updates”) that may affect your ability to copy, display and/or play Secure Content through Microsoft software or third party applications
that utilize Microsoft DRM. You therefore agree that, if you elect to download a license from the Internet which enables your use of Secure Content, MS, Microsoft Corporation or their subsidiaries may, in conjunction with such license, also download onto your DEVICE
such Security Updates that a Secure Content Owner has requested that MS, Microsoft Corporation or their subsidiaries distribute.
MS, Microsoft Corporation or their subsidiaries will not retrieve any personally identifiable information, or any other information, from
your DEVICE by downloading such Security Updates
•
NetMeeting/Remote Assistance/Remote Desktop Features: The SOFTWARE may contain NetMeeting, Remote Assistance, and
Remote Desktop technologies that enable the SOFTWARE or other applications installed on the Device to be used remotely between
two or more computing devices, even if the SOFTWARE or application is installed on only one Device. You may use NetMeeting,
Remote Assistance, and Remote Desktop with all Microsoft products; provided however, use of these technologies with certain Microsoft products may require an additional license. For both Microsoft products and non-Microsoft products, you should consult the
license agreement accompanying the applicable product or contact the applicable licensor to determine whether use of NetMeeting,
Remote Assistance, or Remote Desktop is permitted without an additional license
•
Consent to Use of Data: You agree that MS, Microsoft Corporation and their affiliates may collect and use technical information
gathered in any manner as part of product support services related to the SOFTWARE. MS, Microsoft Corporation and their affiliates
may use this information solely to improve their products or to provide customized services or technologies to you. MS, Microsoft
Corporation and their affiliates may disclose this information to others, but not in a form that personally identifies you
•
Internet Gaming/Update Features: If the SOFTWARE provides, and you choose to utilize, the Internet gaming or update features
within the SOFTWARE, it is necessary to use certain computer system, hardware, and software information to implement the features.
By using these features, you explicitly authorize MS, Microsoft Corporation and/or their designated agent to use this information solely
to improve their products or to provide customized services or technologies to you. MS or Microsoft Corporation may disclose this
information to others, but not in a form that personally identifies you.
•
Internet-Based Services Components: The SOFTWARE may contain components that enable and facilitate the use of certain
Internet-based services. You acknowledge and agree that MS, Microsoft Corporation or their affiliates may automatically check the
version of the SOFTWARE and/or its components that you are utilizing and may provide upgrades or supplements to the SOFTWARE
that may be automatically downloaded to your Device.
•
Links to Third Party Sites: The SOFTWARE may provide you with the ability to link to third party sites through the use of the
SOFTWARE. The third party sites are not under the control of MS, Microsoft Corporation or their affiliates. Neither MS nor Microsoft
Corporation nor their affiliates are responsible for (i) the contents of any third party sites, any links contained in third party sites, or
any changes or updates to third party sites, or (ii) webcasting or any other form of transmission received from any third party sites. If
the SOFTWARE provides links to third party sites, those links are provided to you only as a convenience, and the inclusion of any link
does not imply an endorsement of the third party site by MS, Microsoft Corporation or their affiliates.
•
Additional Software/Services: The SOFTWARE may permit BARCO, MS, Microsoft Corporation or their affiliates to provide or make
available to you SOFTWARE updates, supplements, add-on components, or Internet-based services components of the SOFTWARE
after the date you obtain your initial copy of the SOFTWARE (“Supplemental Components”). If BARCO provides or makes available to
you Supplemental Components and no other EULA terms are provided along with the Supplemental Components, then the terms of
this EULA shall apply. If MS, Microsoft Corporation or their affiliates make available Supplemental Components, and no other EULA
terms are provided, then the terms of this EULA shall apply, except that the MS, Microsoft Corporation or affiliate entity providing the
Supplemental Component(s) shall be the licensor of the Supplemental Component(s). BARCO, MS, Microsoft Corporation and their
affiliates reserve the right to discontinue any Internet-based services provided to you or made available to you through the use of the
SOFTWARE. This EULA does not grant you any rights to use the Windows Media Format Software Development Kit (“WMFSDK”)
components contained in the SOFTWARE to develop a software application that uses Windows Media technology. If you wish to
use the WMFSDK to develop such an application, visit http://msdn.microsoft.com/workshop/imedia/windowsmedia/sdk/wmsdk.asp,
accept a separate license for the WMFSDK, download the appropriate WMFSDK, and install it on your system.
•
PATENT INFRINGEMENTS: Barco disclaims any warranty that its Products do not infringe any patent, copyright or trademark; but
agrees to indemnify you regarding such claims if you promptly notify BARCO in writing and if Barco shall have sole control of the
defense of the action and its settlement or compromise. If the use of a Product is enjoined, or a settlement prevents continued use
of the Product, Barco shall have the option to procure for you the right to continue use, or replace or modify the Product to remove
the infringement. Barco shall have no liability or duty to indemnify you if the infringement or claim is based on use of the Product in
combination with other products or software not furnished by Barco, where such claim would not have arisen if such Product were
used independently. You will hold Barco harmless against any expense or loss resulting from any infringement caused by compliance
with your designs, specifications, or instructions. The foregoing paragraph states Barco’s entire liability with regard to infringement of
patents, copyrights, or trademarks. This warranty on IP infringement only is valid within US, Canada, EC, Austria, Norway and Japan.
Copyright ©
All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded, transmitted or
stored in a retrieval system without the prior written consent of Barco.
Trademarks
Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of their respective holders.
All brand and product names mentioned in this manual serve as comments or examples and are not to be understood as advertising for
the products or their manufactures.
Table of contents
TABLE OF CONTENTS
1. Packaging and Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.1
1.2
1.3
1.4
Box content . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Projector Packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lens Packaging. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
5
6
6
2. Installation Guidelines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.1
2.2
2.3
2.4
Safety warnings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Installation guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Projector configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Lenses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.4.1 Lenses. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.4.2 Lens formulas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.4.3 Lens installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.4.4 Removing the lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.4.5 Cleaning the lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.5 Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.5.1 Battery installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3. Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
3.1
3.2
Power connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Input source connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
3.2.1 Input section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
3.2.2 Input facilities. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.2.3 5-Cable input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.2.4 Composite Video Input. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.2.5 S-Video input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3.2.6 Digital Visual Interface (DVI) input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3.2.7 Computer input. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
3.2.8 Communications Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
3.2.8.1
RS232 IN connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
3.2.9 Extended configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
3.2.9.1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
3.2.9.2
5 cable extended configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
3.2.9.3
S-Video extended configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
3.2.9.4
Summarizing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
4. Getting started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
4.1
4.2
4.3
4.4
4.5
4.6
RCU & Local keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Terminology overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Switching on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Lamp runtime . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Lamp error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Quick set up adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
4.6.1 Quick lens Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
4.6.2 Using the RCU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
4.7 Projector address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
4.7.1 Address setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
4.7.2 Displaying and Programming addresses into the RCU. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
4.8 Controlling the projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
4.9 Digital Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
4.10 Menu structure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
4.11 Using the menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
4.12 Using the Dialogboxes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
5. Source Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
5.1
5.2
5.3
5.4
Source selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Composite Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
S-Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
The Video Selector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
6. General Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
6.1
6.2
6.3
6.4
Pause . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Freeze . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Standby Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Audio (Optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
6.4.1 Audio Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
6.4.2 Audio Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
6.5 Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
7. Image Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
7.1
Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
7.1.1 Contrast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
R5976491 IQ PRO G500 01/02/2007
1
Table of contents
7.1.2 Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
7.1.3 Color. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
7.1.4 Tint (hue) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
7.1.5 Sharpness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
7.1.6 Gamma . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
7.1.7 Phase. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
7.1.8 Noise reduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
7.2 Aspect ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
7.3 Show native resolution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
7.4 Keystone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
7.5 Color temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
7.6 Filmmode detection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
7.7 Blanking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
7.8 Input balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
7.9 AGC on Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
7.10 Manual Gain Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
8. Tools Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
8.1
8.2
8.3
8.4
8.5
Introduction to PiP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
PiP select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
PiP add window. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
PiP remove window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
PiP layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
8.5.1 PiP Save . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
8.5.2 PiP rename layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
8.5.3 PiP delete layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
8.6 PiP Adjust . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
8.7 Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
9. Signal Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
9.1
9.2
Switching mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Background . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
10. Lamp Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
10.1
10.2
10.3
10.4
10.5
10.6
Runtimes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Power mode (only active in the iQG/R 500) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
History. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Reset runtime . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Runtime warning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
11. Image files menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
11.1
11.2
11.3
11.4
11.5
11.6
11.7
Load file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Auto Image. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Edit file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Rename file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100
Copy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101
Delete . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102
Forced file load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103
12. Display setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
12.1
12.2
12.3
12.4
12.5
12.6
12.7
12.8
12.9
Full screen representation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105
Startup screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105
Textbox. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106
Take screenshot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106
Menu bar position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .108
Status bar position. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .108
Sliderbox position. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109
AutoImage Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Blanking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
13. Installation menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
13.1 Lens adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
13.2 Projector address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
13.3 Orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
13.4 Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
13.5 Quick access keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
13.6 RS232 baudrate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
13.7 Automatic startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
13.8 Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
13.9 Change password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .121
13.10 Gemini installed (only for GEMINI CADWALL systems ! ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122
14. IQ Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
14.1 Network architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .123
14.2 Network functionality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .124
14.3 iQ Pro Server specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .125
2
R5976491 IQ PRO G500 01/02/2007
Table of contents
14.4 Getting started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .125
14.4.1 Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .126
14.4.2 Installing the software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .127
14.4.3 Start up of the iQ Pro Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .127
14.4.4 Configuring the client software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .129
14.4.5 Configuring the Server software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .132
14.5 Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .137
14.5.1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .137
14.5.2 How to use the control manager? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .138
14.5.3 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .138
14.5.4 The source selection screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .139
14.5.5 The PiP screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .139
14.5.6 Image settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .142
14.5.7 Advanced control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .144
14.5.7.1 Lens adjustments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .145
14.5.7.2 Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .145
14.6 Management & diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .147
14.6.1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .147
14.6.2 Diagnostics manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .147
14.7 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .148
14.7.1 E-mail messaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .148
14.7.2 E-mail configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .148
14.7.3 Projector Firmware Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .149
14.8 DropZone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .151
14.8.1 Dropzone tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .151
14.8.2 Start up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .151
14.8.3 File dropping/launching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .153
14.8.4 Open remotely a file on the projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .155
14.8.5 Remote desktop sharing (virtual meeting) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .155
14.8.6 DropZone settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .158
14.9 The Web client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .159
15. General guidelines on Network Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
15.1 General Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .161
15.2 The Internet and Web services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .161
A. Exchange. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
A.1
Exchange Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .163
A.1.1 Installation procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .163
A.1.2 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .164
A.2 Exchange Integration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .165
A.2.1 Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .165
A.2.2 Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .167
A.2.3 Microsoft Outlook Integration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .167
A.2.4 Folder form . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .169
A.2.5 Limitations and known “problems”. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .170
B. SNMP services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171
B.1
B.2
SNMP installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .171
SNMP integration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .171
C. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173
C.1
FAQ table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .173
D. Cleaning the dustfilters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
D.1
D.2
Dustfilters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .175
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .175
E. Standard Image Files. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
E.1
Table overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .177
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183
Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185
R5976491 IQ PRO G500 01/02/2007
3
Table of contents
4
R5976491 IQ PRO G500 01/02/2007
1. Packaging and Dimensions
1. PACKAGING AND DIMENSIONS
Overview
•
Box content
•
Projector Packaging
•
Lens Packaging
•
Dimensions
1.1
Box content
CEE7
European power plug to connect the power cord to the wall outlet.
ANSI 73.11
American power plug to connect the power cord to the wall outlet.
Content
•
1.2
1 projector (weight ± 12,6 kg or 27.8 lbs)
•
1 remote control unit RCU + 2 batteries.
•
2 power cables with outlet plug type CEE7 and ANSI 73.11.
•
1 owners manual
•
1 safety manual
Projector Packaging
Way of Packaging
The projector is packed in a carton box. To provide protection during transportation, the projector is surrounded with foam. The
package is secured with banding and fastening clips.
To unpack
1. Release the fastening clips. (image 1-1)
2. Remove the banding. Handle as shown in the drawing.
3. Take the projector out of its shipping carton and place it on a table. (image 1-2)
R5976491 IQ PRO G500 01/02/2007
5
1. Packaging and Dimensions
R824561
R824562
Projector
PULL
TO OPE
R824518
(+ cable basket R724408
Image 1-1
R825784
Image 1-2
Save the original shipping carton and packing material, they will be necessary if you ever have to ship your
projector. For maximum protection, repack your projector as it was originally packed at the factory.
Save the original shipping carton and packing material, they will be necessary if you ever have to ship your
projector. For maximum protection, repack your projector as it was originally packed at the factory.
CAUTION:
Never transport the projector with the lens mounted on it !
Always remove the lens before transporting the projector.
1.3
Lens Packaging
Way of Packaging
Lenses are supplied as an individual item.
They are packed in a carton box.
Save the original shipping carton and packing material, they will be necessary if you ever have to transport
the lens.
CAUTION:
Never transport the projector with the lens mounted on it !
Always remove the lens before transporting the projector.
1.4
Dimensions
Dimensions overview
Dimensions are given in mm (1 inch = 25.4 mm)
6
R5976491 IQ PRO G500 01/02/2007
1. Packaging and Dimensions
487
152
281
305
78
45
380
20
69
195
Length with different lenses, see table
415
Cold air in
Hot air out
565
Image 1-3
R5976491 IQ PRO G500 01/02/2007
7
1. Packaging and Dimensions
8
Lens
length of projector
combinable with cable
basket
Remarks
SVD(2-2.5:1)
545mm
YES
Length with cable basket = 565mm
QVD(1.3-1.8:1)
600mm
YES
QVD(1.9-2.6:1)
590mm
YES
QVD(3.0-6.0:1)
620mm
YES
QVD(0.85:1)
545mm
NO
QVD(7.0:1)
540mm
YES
Length with cable basket = 560mm
R5976491 IQ PRO G500 01/02/2007
2. Installation Guidelines
2. INSTALLATION GUIDELINES
Overview
•
Safety warnings
•
Installation guidelines
•
Projector configurations
•
Lenses
•
Batteries
2.1
Safety warnings
WARNING: Before installing the projector, read first the safety instructions in the safety manual (R5975258)
delivered with the projector.
Insure that the projector is installed in an easy to evacuate room in case of a lamp explosion.
Mercury Vapor Warnings
Keep the following warnings in mind when using the projector. The lamp used in the projector contains mercury. In case of a lamp
rupture, explosion there will be a mercury vapor emission. In order to minimize the potential risk of inhaling mercury vapors:
2.2
•
Ensure the projector is installed only in ventilated rooms.
•
Replace the lamp module before the end of its operational life.
•
Promptly ventilate the room after a lamp rupture, explosion has occurred, evacuate the room (particularly in case of a pregnant
woman).
•
Seek medical attention if unusual health conditions occur after a lamp rupture, explosion, such as headache, fatigue, shortness
of breath, chest-tightening coughing or nausea.
Installation guidelines
Ambient temperature check
Careful consideration of things such as image size, ambient light level, projector placement and type of screen to use are critical to
the optimum use of the projection system.
Max. ambient temperature : 40 °C or 104 °F
Min. ambient temperature : 0 °C or 32 °F
The projector will not operate if ambient air temperature falls outside this range (0°C- 40°C or 32°F-104°F).
Environment
Do not install the projection system in a site near heat sources such as radiators or air ducts, or in a place subject to direct sunlight,
excessive dust or humidity. Be aware that room heat rises to the ceiling; check that temperature near the installation site is not
excessive
CAUTION:
Harmful Environmental Contamination Precaution
Environment condition check
A projector must always be mounted in a manner which ensures the free flow of clean air into the projectors ventilation inlets as well
as free flow at the ventilation outlets. The installation must also allow easy access to the consumable parts ( dustfilters, lamps, ...)
For installations in environments where the projector is subject to airborne contaminants such as that produced by smoke machines
or similar (these deposit a thin layer of greasy residue upon the projectors internal optics and imaging electronic surfaces, degrading
performance), then it is highly advisable and desirable to have this contamination removed prior to it reaching the projectors clean
air supply. Devices or structures to extract or shield contaminated air well away from the projector are a prerequisite, if this is not
a feasible solution then measures to relocate the projector to a clean air environment should be considered. Make sure that the
projector never runs with dirty dustfilters as this will dramatically reduce the lifetime of the consumables. It is advised to clean the
dustfilters on a regular basis and to replace them at any lamp change. Barco reserves itself the right to refuse warranty replacement
of consumables if they have been used in a projector with dirty airfilters. Only use the manufactures recommended cleaning kit which
R5976491 IQ PRO G500 01/02/2007
9
2. Installation Guidelines
has been specifically designed for cleaning optical parts, never use industrial strength cleaners on a projectors optics as these will
degrade optical coatings and damage sensitive optoelectronics .
Failure to take suitable precautions to protect the projector from the effects of persistent and prolonged air contaminants will culminate in extensive and irreversible ingrained optical damage. At this stage cleaning of the internal optical units will be non-effective
and impracticable. Damage of this nature is under no circumstances covered under the manufactures warranty and may deem the
warranty null and void. In such a case the client shall be held solely responsible for all costs incurred during any repair. It is the
clients responsibility to ensure at all times that the projector is protected from the harmful effects of hostile airborne particles in the
environment of the projector. The manufacture reserves the right to refuse warranty repair if a projector has been subject to wantful
neglect, abandon or improper use.
What about ambient light ?
The ambient light level of any room is made up of direct or indirect sunlight and the light fixtures in the room. The amount of ambient
light will determine how bright the image will appear. So, avoid direct light on the screen. Windows that face the screen should be
covered by opaque drapery while the set is being viewed. It is desirable to install the projection system in a room whose walls and
floor are of non-reflecting material. The use of recessed ceiling lights and a method of dimming those lights to an acceptable level
is also important. Too much ambient light will ‘wash out’ of the projected image. This appears as less contrast between the darkest
and lightest parts of the image. With bigger screens, the ‘wash out’ becomes more important. As a general rule, darken the room to
the point where there is just sufficient light to read or write comfortably. Spot lighting is desirable for illuminating small areas so that
interference with the screen is minimal.
Which screen type ?
There are two major categories of screens used for projection equipment. Those used for front projected images and those for rear
projection applications. Screens are rated by how much light they reflect (or transmit in the case of rear projection systems) given a
determined amount of light projected toward them. The ‘GAIN’ of a screen is the term used. Front and rear screens are both rated
in terms of gain. The gain of screens range from a white matte screen with a gain of 1 (x1) to a brushed aluminized screen with a
gain of 10 (x10) or more. The choice between higher and lower gain screens is largely a matter of personal preference and another
consideration called the Viewing angle. In considering the type of screen to choose, determine where the viewers will be located
and go for the highest gain screen possible. A high gain screen will provide a brighter picture but reduce the viewing angle. For
more information about screens, contact your local screen supplier.
Image size
The projector is designed for projecting an image size with a screenwidth from 1.00m (3.3ft) to 6.00m (19.7ft) with an aspect ratio of
4 to 3.
Image retention
Image retention can affect LCD projectors, in extreme cases, permanent “burn” can occur if still/repetitive images are left on the
screen for long periods of time. Such damage to the panels is NOT covered by warranty.
Please ensure that the following precautions are taken to avoid this phenomenon :
1.
Use a screensaver (that moves)
2.
Periodically change/alter any background images on the desktop
3.
Turn off the projector when not in use.
2.3
Projector configurations
The different configurations
10
1.
Rear/Ceiling
2.
Rear/Table
3.
Front/Ceiling
4.
Front/Table
R5976491 IQ PRO G500 01/02/2007
2. Installation Guidelines
1
2
3
4
Image 2-1
R5976491 IQ PRO G500 01/02/2007
11
2. Installation Guidelines
Positioning the projector
PD
P
front plate
x
SH
a
A
S
CD=SH/2+B-A
B
F
b
SW
S
SW
SH
c
F
Image 2-2
ON-Axis installation
a
b
c
x
p
s
F
12
side view
top view
back view
optical axis projection lens
projector
screen
floor
R5976491 IQ PRO G500 01/02/2007
2. Installation Guidelines
PD
a
SH
front plate
P
S
A
B
CD=B-A
F
b
SW
S
SW
c
SH
F
Image 2-3
100% OFF Axis installation
a
b
c
x
p
s
F
side view
top view
back view
optical axis projection lens
projector
screen
floor
CAUTION:
Only for iQ Pro:
The harddisk in the IQ Pro server is formatted in horizontal position but can operate in all axes (6 directions).
The projector should not be tilted more then +/- 5 degrees from these positions, otherwise error rates will
increase.
R5976491 IQ PRO G500 01/02/2007
13
2. Installation Guidelines
CAUTION:
Floor
Never place the projector on either side !
Floor
Image 2-4
2.4
Lenses
Overview
2.4.1
•
Lenses
•
Lens formulas
•
Lens installation
•
Removing the lens
•
Cleaning the lens
Lenses
Available lenses
The following lenses are available, or will become available (contact a BARCO service center) as an option :
Lenses
Standard version
QVD(0.85:1)
R9841220
QVD(1.3-1.8:1)
R9840950
QVD(1.9-2.6:1)
R9840960
QVD(3.0-6.0:1)
R9840970
QVD(7:1)
R9841230
SVD(2.0-2.5:1)
R9841240
The QVD (0.85:1) is to be used in ON Axis configuration only.
Shifting the lens vertically will not guarantee optimal image quality.
14
R5976491 IQ PRO G500 01/02/2007
2. Installation Guidelines
2.4.2
Lens formulas
Formulas
Metric Formulas (meter)
Inch formulas (inch)
QVD(0.85:1)
PD = -0.034 + 0.801 x SW + 0.0086 /SW
PD = -1.34 + 0.801 x SW + 13.35 /SW
QVD(1.3-1.8:1)
PDmin = 0.019 + 1.216xSW + 0.028/SW
PDmin = 0.75 + 1.216xSW + 43.4/SW
PDmax = -0.001 + 1.584xSW + 0.074/SW
PDmax = -0.04 + 1.584xSW + 115/SW
PDmin = 0.052 + 1.731xSW - 0.014/SW
PDmin = 2.05 + 1.731xSW - 21.7/SW
PDmax = 0.11 + 2.33xSW - 0.059/SW
PDmax = 4.33 + 2.33xSW - 91.8/SW
PDmin = 0.048 + 2.795xSW - 0.042/SW
PDmin = 1.89 + 2.795xSW - 65/SW
PDmax = 0.06 + 5.6xSW - 0.041/SW
PDmax = 2.36 + 5.6xSW - 63.4/SW
QVD(7:1)
PD = 0.013 + 6.35xSW + 0.005/SW
PD = 0.51 + 6.35xSW + 8.35/SW
SVD(2.0-2.5:1)
PDmin = -0.139 + 1.733xSW + 0.1/SW
PDmin = -5.47 + 1.733xSW + 153/SW
PDmax = 0.005 + 2.224xSW - 0.00862/SW
PDmax = 0.2 + 2.224xSW - 13.3/SW
QVD(1.9-2.6:1)
QVD(3.0-6.0:1)
Lens program to calculate the projector distance is available on the
http://www.barco.com/projection_systems/customer_services/lens_program.asp
2.4.3
BARCO
web
site
:
Lens installation
How to install ?
1. Take the lens out of its packing material
2. Slide the lens door to the left (image 2-5)
3. Fix the lens by placing it in the housing
Note: In case of a motorized lens the female jack must be in front of the male jack located in the upper-left part of the housing
in the projector (image 2-6)
4. Push carefully to lock the lens in the housing
5. Slide back the lens door to the right
R5976491 IQ PRO G500 01/02/2007
15
2. Installation Guidelines
Image 2-5
Image 2-6
CAUTION: Never transport the projector (or the whole unit) with the lens mounted on it !
Always remove the
lens and transport it separately.
2.4.4
Removing the lens
How to remove the lens ?
1. Slide the lens door to the left.
2. Unlock the lens by pulling the handle located on the right side of the projector (image 2-7)
3. Remove the lens out of its housing
Image 2-7
CAUTION:
Never transport the projector with the lens mounted on it !
Always remove the lens before transporting the projector.
16
R5976491 IQ PRO G500 01/02/2007
2. Installation Guidelines
2.4.5
Cleaning the lens
To minimize the possibility of damage to optical coatings, or scratches to lens surfaces, we have developed
recommendations for cleaning. FIRST, we recommend you try to remove any material from the lens by blowing
it off with clean, dry deionized air. DO NOT use any liquid to clean the lenses.
Necessary tools
Toraysee TM cloth (delivered together with the lens kit). Order number : R379058.
How to clean the lens ?
Proceed as follow :
1. Always wipe lenses with a CLEAN Toraysee TM cloth.
2. Always wipe lenses in a single direction.
Warning: Do not wipe back and forwards across the lens surface as this tends to grind dirt into the coating.
3. Do not leave cleaning cloth in either an open room or lab coat pocket, as doing so can contaminate the cloth.
4. If smears occur when cleaning lenses, replace the cloth. Smears are the first indication of a dirty cloth.
CAUTION: Do not use fabric softener when washing the cleaning cloth or softener sheets when drying the
cloth.
Do not use liquid cleaners on the cloth as doing so will contaminate the cloth.
Other lenses can also be cleaned safely with this Toraysee TM cloth.
2.5
Batteries
Overview
•
2.5.1
Battery installation
Battery installation
How to install the battery
Two batteries are packed together with the RCU. Before using your RCU, install first these batteries.
1. Remove the battery cover on the backside by pushing the handle a little towards the bottom of the RCU.
2. Lift up the top side of the cover at the same time.
3. Insert the batteries as indicated in the RCU.
4. Put the battery cover on its place.
R5976491 IQ PRO G500 01/02/2007
17
2. Installation Guidelines
18
R5976491 IQ PRO G500 01/02/2007
3. Connections
3. CONNECTIONS
Overview
•
Power connection
•
Input source connection
3.1
Power connection
AC power (mains) cord connection
Use the supplied power cord to connect your projector to the wall outlet.
Plug the female power connector into the male connector at the front of the projector.
The power input is auto-ranging from 90 to 240 VAC.
I
0
Image 3-1
Fuses
For continued protection against fire hazard :
•
refer replacement to qualified service personnel
•
ask to replace with the same type of fuse.
3.2
Input source connection
Overview
•
3.2.1
Input section
•
Input facilities
•
5-Cable input
•
Composite Video Input
•
S-Video input
•
Digital Visual Interface (DVI) input
•
Computer input
•
Communications Connections
•
Extended configuration
Input section
Input Layers
The input section is divided in layers, each of them regrouping several inputs.
R5976491 IQ PRO G500 01/02/2007
19
3. Connections
1.
Layer 1: analog layer containing analog data and video inputs
2.
Layer 2: a hybrid layer containing 2 digital and 1 analog input
3.
Layer 3 : network layer
3.2.2
Input facilities
overview
•
5–cable input
•
composite video
•
component video (PR/Y/PB)
•
S-Video
•
Digital Visual Input (DVI)
•
Computer
•
network interface
Image 3-2
Source input section, the LED’s indicate the selection of a signal.
L1 Layer 1 = RGBHV (data) + Composite Video + S-Video
L2 Layer 2 = DVI + Computer + RS232 IN + RC (Wired Remote Control)
L3 Layer 3 = network Layer = Mic IN + Line IN + PC Card slot+ 4xUSB in + RJ45
20
R5976491 IQ PRO G500 01/02/2007
3. Connections
A cable cover is supplied with the projector and can be fitted on the front of the projector
Image 3-3
Cable basket : the white arrow shows the cables leaving the projector
A
B
3.2.3
Front view
Back view
5-Cable input
Input specifications
The 5-cable input section is made of 5 BNC input terminals.
0.7 Vpp ± 3dB
75 Ω terminated
Image 3-4
Component Video
In Component Video the term component describes a number (3) of elements that are needed to make up the video
picture, these components are R-Y/Y/B-Y. A composite video signal on the other hand contains all the information
needed for the color picture in a single channel of information
Which signals can be connected ?
Signals/Input BNC
R
G
B
H
V
RGBHV
R
G
B
H
V
RG sB1
R
Gs
B
-
-
RGBS1
R
G
B
S
-
Component
PR
Y
PB
-
-
1. data or video
R5976491 IQ PRO G500 01/02/2007
21
3. Connections
Beside the standard RGB, component and sync signals, the extended mode of the 5 Cable input makes processing of additional signals possible.
How to select a source on the 5 cable input ?
1. Press 1 on the RCU
Note: Another way for selecting this input is via the Menu
Component Video signals (PR/Y/PB)
Some interfaces use progressive output signals with a double line frequency of 32 kHz. The video decoder
used for the video signals is not appropriate for these signals since it can only handle 16 kHz signals. This
signal has therefore to be internally redirected, this is done in the Source selection menu by selecting Data on
BNC’s instead of Component video and by selecting Pr/Y/Pb in the advanced settings of the Image file menu.
3.2.4
Composite Video Input
Composite video connection
A Composite video signal is often available on a yellow cinch connector of a Camera, VCR or DVD player, in this case you will need
an adapter cable cinch/BNC to connect to Video input of the RGB board.
Input specifications
The Composite video input section is made of 1BNC input terminal.
1.0 Vpp ± 3dB
75 Ω terminated
No loop through
Image 3-5
How to select a Composite Video Input ?
1. Press 3 on the RCU
Note: Another way for selecting this input is via the Menu.
The projector allows the input of more composite video signals (up to 7 composite video signals).
"5 cable extended configuration", page 25
This note is not valid for the Pro version :
The Audio&Video optional layer(3) allows the use of an additional Video BNC input (referred to as Video2).
The selection of this optional input happens the same way as the standard input (key 3)
22
R5976491 IQ PRO G500 01/02/2007
3. Connections
3.2.5
S-Video input
S-Video connection
An S-Video signal is available on the Mini-Din connector of a camera, VCR or DVD player.
Input specification
Image 3-6
Which signal can be connected ?
Standard S-Video (S-VHS) with separate Y(luma) and C (chroma) signals.
How to select the S-Video input ?
1. Press 4 on the RCU
Note: Another way for selecting this input is via the Menu.
The projector allows the input of more S-Video signals (up to 3 composite video signals).
"S-Video extended configuration", page 26
This note is not valid for the Pro version:
The Audio&Video optional layer(3) allows the use of an additional S-Video input (referred to as S-Video4).
The selection of this optional input happens the same way as the standard input (key 4)
3.2.6
Digital Visual Interface (DVI) input
DVI
Digital Visual Interface is a display interface developed in response to the proliferation of digital flat panel displays.
The digital video connectivity standard that was developed by DDWG (Digital Display Work Group). This connection
standard offers two different connectors: one with 24 pins that handles digital video signals only, and one with 29 pins
that handles both digital and analog video. This standard uses TMDS (Transition Minimized Differential Signal) from
Silicon Image and DDC (Display Data Channel) from VESA (Video Electronics Standards Association).
DVI can be single or dual link.
Input specifications
Single link DVI
Differential input voltage: 200 mV - 800mV
R5976491 IQ PRO G500 01/02/2007
23
3. Connections
Image 3-7
a
DVI-I type connector, analog link (4 pins at the right side of the connector) not supported
How to select the DVI Input ?
1. Press 5 on the RCU
Note: Another way for selecting this input is via the Menu.
3.2.7
Computer input
Input specification
TTL sync input : U
min
= 2.0 V
RGB input = 0.7 V pp ± 3dB
Image 3-8
What can be connected ?
•
RGBHV
•
RG SB
Composite sync only possible on Green
How to select a computer input ?
1. Press 2 on the RCU
Note: Another way for selecting this input is via the Menu.
3.2.8
Communications Connections
Overview
•
24
RS232 IN connection
R5976491 IQ PRO G500 01/02/2007
3. Connections
3.2.8.1
RS232 IN connection
What can be connected to the RS232 IN connection ?
The RS 232 IN connections allows the projector to communicate with a Computer e.g. IBM PC or Apple Macintosh.
Image 3-9
Applications of the RS232 connection
Remote control:
•
easy adjustment of projector via IBM PC (or compatible) or MAC connection.
•
address range from 1 to 255
•
allow storage of multiple projector configurations and set ups.
•
wide range of control possibilities
Data communication: sending data to the projector or copying the data from the projector to the computer
To set up the baudrate of the projector, see the Installation menu
3.2.9
Extended configuration
Overview
•
Introduction
•
5 cable extended configuration
•
S-Video extended configuration
•
Summarizing
3.2.9.1
Introduction
What can be done ?
The PiP mode allows to display up to 4 windows of images coming from different sources. The extended capabilities on the input
board allow therefore to combine several data & video sources, beside that, they allow switching between a wide range of input
signals.
3.2.9.2
5 cable extended configuration
What can be done ?
Beside the standard RGB, composite & sync signals, the extended capabilities of the 5 cable inputs make treatment of additional
signals possible:
•
a composite video signal may be connected to 4 of the 5 BNC’s (beside the standard video BNC input)
•
a S-Video signal can be connected
R5976491 IQ PRO G500 01/02/2007
25
3. Connections
Inputs
Signals
R
G
B
H
V
VIDEO
RGBHV
R
G
B
H
V
-
RG SB
R
GS
B
-
-
-
RGBS
R
G
B
S
-
-
PR
Y
PB
-
-
-
S-Video
-
-
-
-
C
Y
S-Video
C
-
Y
-
-
-
Composite
VIDEO
-
-
-
-
-
Composite
-
VIDEO
-
-
-
-
Composite
-
-
VIDEO
-
-
-
Composite
-
-
-
-
VIDEO
Composite
-
-
-
-
-
Component
VIDEO
Table 3-2
Extended configuration of the 5 cable input: the first column gives the possible signals, and the first row the 5 cable input connectors (+ the standard Video BNC).
How to set up the 5 cable extended configuration ?
1. Connect the video or S-video source to the desired BNC connector
Note: In some cases an adapter cable is required (image 3-10, image 3-11, image 3-12)
Image 3-10
Connecting an S-Video signal on the Vs &
Video BNC
Image 3-11
Connecting an S-Video signal on the R & B
BNC
Image 3-12
Connecting composite Video signals on the
5 cable input
Multiple video signals can not be visualized simultaneously since there is only one decoder. However, the use
of the optional Audio & video layer(3) allows to visualize up to 2 different video signals (in PiP mode ).
3.2.9.3
S-Video extended configuration
What can be done ?
Beside the standard luminance (Y) and chrominance (C) signals, the advanced capabilities of the S-Video input make treatment of
additional signals possible:
•
2 composite video signal may be connected.
Inputs
Signals
Y
C
Y
C
Composite Video
Video
-
Composite Video
-
Video
S-Video
Table 3-3
Extended configuration of the S-Video input: the first column gives the possible signals, and the first row the S-Video inputs pins.
26
R5976491 IQ PRO G500 01/02/2007
3. Connections
How to set up the S-Video extended configuration ?
1. Connect the video sources to the desired connector (image 3-13)
Note: An adapter cable is required
Image 3-13
Connecting 2 composite Video signals on the S-Video connector
Multiple video signals can not be visualized simultaneously since there is only one decoder. However, the use
of the optional Audio & video layer(3) allows to visualize up to 2 different video signals (in PiP mode ).
3.2.9.4
Summarizing
Summarizing the extended connections
A composite video signal can be entered via 7 different inputs, which gives us 7 different video signals (not including
optional video input):
1.
Video R : via 1st BNC
2.
Video G : via 2nd BNC
3.
Video B : via 3rd BNC
4.
Video VS : via 5th BNC
5.
Video : via the standard composite video BNC input
6.
Video Y : via S-Video input
7.
Video C : via S-Video input
Key 3 on the RCU allows to browse through the active video inputs, each hit moves to the next active video input. The first hit on
key 3 selects the last selected video input.
In the same way 3 S-Video signals can be visualized through 3 different inputs
1.
S-Video 1: via the standard S-Video input
2.
S-Video 2 : via the 5 the BNC and the standard Composite Video input
3.
S-Video 3 : via the 1st and the 3rd BNC
Key 4 on the RCU allows to browse through the active S-Video inputs, each hit moves to the next active video input. The first hit on
key 4 selects the last selected video input.
R5976491 IQ PRO G500 01/02/2007
27
3. Connections
28
R5976491 IQ PRO G500 01/02/2007
4. Getting started
4. GETTING STARTED
Overview
4.1
•
RCU & Local keypad
•
Terminology overview
•
Switching on
•
Lamp runtime
•
Lamp error
•
Quick set up adjustments
•
Projector address
•
Controlling the projector
•
Digital Zoom
•
Menu structure
•
Using the menu
•
Using the Dialogboxes
RCU & Local keypad
How controlling the projector ?
The projector can be controlled by the local keypad or by the remote control unit.
Location of the local keypad ?
The local keypad is located on the topside of the projector.
For key overview: "Terminology overview", page 31
R5976491 IQ PRO G500 01/02/2007
29
4. Getting started
Image 4-1
Local keypad layout
Remote control functions.
This remote control includes a battery powered infrared (IR) transmitter that allows the user to control the projector remotely. This
remote control is used for source selection, control, adaptation and set up. It includes automatic storing of picture controls (Brightness, Sharpness...) and settings.
Other functions of the remote control are :
•
switching between stand by and operational mode.
•
switching to "pause" (blanked picture, full power for immediate restarting)
•
direct access to all connected sources.
Diagnose LED’s
LED1
LED2
Green
Red
cool down sequence: flickers 60 seconds (120
seconds in case of iQ 400 series) after switching
to standby
rescue program (software error)
only for the versions containing a server:
shows when projector is in
hardware error
standby and server is active.
LED3
IR acknowledgement
continue : standby
flickers : Security = ON
30
R5976491 IQ PRO G500 01/02/2007
4. Getting started
4.2
Terminology overview
Overview
The following table gives an overview of the keys.
Image 4-2
1
Function keys
user programmable keys with functions for direct access.
2
MENU
Menu key, to enter or exit the Toolbar menu.
3
Address key
(recessed key), to enter the address of the projector (between 0 and 9). Press the recessed
address key with a pencil, followed by pressing one digit button between 0 and 9.
4
LOGO key
allows to recall the stored Logo (not in PiP mode)
5
PAUSE
to stop projection for a short time, press ’PAUSE’. The image disappears but full power is
retained for immediate restarting.
6
STBY
standby button, to start projector when the power switch is switched on and to switch off the
projector without switching off the power switch.
Attention : Switching to Standby. When the projector is running and you want to
go to standby, press the standby key for 2 seconds.
7
MUTE
to interrupt the sound reproduction (audio = optional.
8
AUTOIMAGE
Auto image, to center the image on the active LCD surface.
9
Digit buttons
direct input selection.
9b
SOURCE button
this button allows to switch through the active (scanned) inputs
R5976491 IQ PRO G500 01/02/2007
31
4. Getting started
10
Lens control
use these buttons to obtain the desired ZOOM, SHIFT, FOCUS.
11
VOL
use this button to obtain the desired sound level (audio = optional)
12
Picture controls
use these buttons to obtain the desired picture analog level.
13
DIGI ZOOM
allows a digital Zoom of a part of the image
14
FREEZ
press to freeze the projected image.
15
PIP
allows to activate the PICTURE IN PICTURE mode
16
ENTER
to confirm an adjustment or selection in the MENU.
On the local keypad the ENTER button additionally accesses the PIP window resize function
17
Cursor keys
Cursor Keys on RCU or on the local keypad : to make menu selections or to access the
toolbar.
18
BACK
to leave the selected menu or item (go upwards to previous menu).
19
EFFECTS
not yet implemented
20
PIP ADJUST
allows to select a PiP window and change its configuration on screen
21
RC operating indication
lights up when a button on the remote control is pressed. (This is a visual indicator to
check the operation of the remote control)
22
IR receiver
IR receiver
Table 4-2
ordernumber RCU: R763794K
4.3
Switching on
How to switch on.
1. Press the power switch to switch on the projector.
-
When ’0’ is pushed in, the projector is switched off.
-
When ’1’ is pushed in, the projector is switched on
The projector starts in standby mode, LED3 is red.
Starting image projection.
1. Press Standby key once on the local keypad or on the remote control. (image 4-3)
M EN
U
B A C K
EN
PA
U SE
L O G O
T ER
PI P
D IG I
Z O O M
9
0
PH
A SE
Image 4-3
It may take about 60 seconds before image projection, i.e. no projection until the completion of several operations (software initialization,...).
32
R5976491 IQ PRO G500 01/02/2007
4. Getting started
If the Security mode is enabled, a textbox will be displayed for PIN code entry, see Security setting in the
Installation menu
4.4
Lamp runtime
x
To generalize for the different projector types, x refers here to the maximum run time of the lamp.
Lamp runtime indication while running
Independently of the lamp mode, when the total runtime of an active lamp (lamp1 for example) is (x-30) hours or more, a warning
message will be displayed.
Image 4-4
Lamp runtime management
A
B
x
single mode
dual mode
maximum lamp runtime
Image 4-5
warning message in case of an iQ300 projector
This warning message will be repeated at the next start up. Press BACK or MENU to remove the message.
R5976491 IQ PRO G500 01/02/2007
33
4. Getting started
The total lifetime of the lamp for a safe operation is “x” hours max, do not use it longer. Always replace with a same type of lamp.
Call a BARCO authorized service technician for lamp replacement.
iQ Pro
x ( Max lamp runtime, in hours)
210L
6000
350
3000
500
1500
Table 4-3
Maximum runtime for the different iQ Pro projectors
When the lamp runtime reaches “x” hours the projector switches automatically to the other lamp, being lamp2.. following messages
are displayed during and after switching.
Image 4-6
Image 4-7
When lamp2 at its turn reaches x-30 hours, a warning message appears on the screen.
Image 4-8
warning message in case of a IQ300 series projector
At the end of the lifetime of lamp2 (x hours) the projector generates an alert message.
Image 4-9
A countdown time of 4 minutes is triggered before the projector is shut down (standby).
If the lamp runtime has not been reset, the alert message will reappear at the next start up (with again 4 minutes countdown time).
This alert message can be escaped with MENU or BACK, but the countdown continues.
Contact a qualified Barco technician for lamp replacement.
In Dual mode the lamp end of lifetimes are reached at the same time, however if in dual lamp mode one lamp
has been used more than the other (for example if the projector has been working temporarily in single mode),
one lamp will reach its end of lifetime sooner than the other lamp, which brings us to the Single mode operation.
WARNING: Using a lamp for more than x hours is dangerous as the lamp could explode.
The lamp runtime reset as well as the lamp replacement can only be done by a Barco authorized technician.
4.5
Lamp error
What happens in case of a lamp error ?
When a lamp error occurs in dual mode, a dialogbox is displayed informing the user of the steps to be taken.
34
R5976491 IQ PRO G500 01/02/2007
4. Getting started
Image 4-10
The message will dissapear after 2 minutes, it can also be escaped.
The projector will switch to single lamp mode and displays an icon (right top corner of the screen) representing a crossed out lamp,
that way informing the user of an earlier lamp error.
The icon can always be removed via the Clear lamp error function in the Lamp menu.
WARNING:
4.6
In case of lamp error contact a Barco authorized technician.
Quick set up adjustments
Overview
4.6.1
•
Quick lens Adjustment
•
Using the RCU
Quick lens Adjustment
What can be done ?
For a quick lens set up and image shift, use the RCU dedicated keys or the lens button on the local keypad
Zoom/focus are only available for motorized lenses.
Quick zoom/focus adjustment
1. Press LENS ZOOM or
LENS FOCUS on the RCU
2. Use the arrow keys to adjust
Quick shift adjustment
1. Press LENS SHIFT
2. Use the arrow keys to adjust
4.6.2
Using the RCU
Pointing to a reflective screen
1. Point the front of the RCU to the reflective screen surface. (image 4-11)
R5976491 IQ PRO G500 01/02/2007
35
4. Getting started
Image 4-11
When using the remote control, make sure you are within the effective operating distance.
The operating distance may be up to 15 m (50ft).
The remote control unit will not function properly if strong light strikes the sensor window or if there are
obstacles between the remote control and the IR sensor.
How to connect ?
1. Plug one end of the remote cable in the connector on the bottom of the RCU.
2. Plug the other end in the connector in the front panel of the projector labelled RC. (image 4-12)
Image 4-12
Specifications of the RC input
U in = 9V
I max = 80 mA
Internal IR receivers can be disabled:
36
•
mono jack : on plug in of the jack
•
stereo jack : on plug in or using an external switch bringing the right channel (B) to ground level.
R5976491 IQ PRO G500 01/02/2007
4. Getting started
A
B
C
D
Image 4-13
Stereo jack pin configuration
A
B
C
D
tip: Left channel
ring: right channel
screen: common (GND)
external switch
The Remote connection uses a standard two wire cable terminated on each end with a 3.5 mm male
(mono/stereo) phone jack.
This cable is not delivered but is available in most electronical or audio shops.
4.7
Projector address
Overview
•
Address setting
•
Displaying and Programming addresses into the RCU
4.7.1
Address setting
Projector address
Address installed in the projector to be individually controlled.
Common address
Default address. Projector will always execute the command coming from a RCU programmed with that common
address.
Why a projector address ?
As more than one projector can be installed in a room, the separate projector should be separately addressable with an RCU or
computer. Therefor each projector has its own address.
Set up an individual Projector Address.
The set up of a projector address can be done via the software.
Projector controlling.
Every projector requires an individual address between 0 and 255 which can be set in the Installation menu.
When the address is set, the projector can be controlled by :
•
RCU for addresses between 0 and 9.
•
computer, e.g. IBM PC (or compatible), Apple MAC, etc. for addresses between 0 and 255.
A projector will respond to a RCU set to the common address ’0’ regardless of what address is set in the projector itself (common
address of projector should also be “0” ).
The RCU is default programmed with address 0 , ’common address’.
If it is necessary to control a specific projector, then enter the projector address into the RCU (only when that
address is between 0 and 9). The projector with the corresponding address will listen to that specific RCU.
R5976491 IQ PRO G500 01/02/2007
37
4. Getting started
Some projectors may operate in domestic environments where other equipments may listen to the common
address “0” , therefore the common address can also be set to “1”.
4.7.2
Displaying and Programming addresses into the RCU
Displaying the Projector Address on the Screen.
1. Press the Address key (recessed key on the RCU) with a pencil.
The projector’s address will be displayed in a ’Text box’
To continue using the RCU with that specific address, it is necessary to enter the same address with the
digit buttons (address between 0 and 9) within 5 seconds after pushing the address key. For example : if the
Address key displays projector address 003, then press "3" digit button on the RCU to set the RCU’s address
to match the projector’s address. Do not press 0–0–3 . This will address the remote control to ’0’ and control
all projectors in the room. If the address is not entered within 5 seconds, the RCU returns to its default address
(zero address) and controls then all projectors in the room.
Address 0 (or 1) should always allow communication with the projector since it is a common address.
Displaying the Projector Address in Standby.
1. Press the Address key (recessed key on the RCU) with a pencil.
All the LED’s on the front of the projector go out.
Then LED1 starts blinking green the number of hundreds. After that LED2 starts blinking the number of tens. Finally LED3 starts
blinking green the number of units. If this is done, the original status of the leds is restored.
4.8
Controlling the projector
Input Selection
Key in the corresponding slot number with the digit keys on the RCU. The selected source will be displayed.
Picture Controls
When an image control is pressed, a text box with a bar scale, icon and function name of the control, e.g. ’brightness...’ appears
on the screen (only if Textbox in the Installation menu is ON). The length of the bar scale and the value of the numeric indication
indicate the current memorized setting for this source. The bar scale changes as the arrows on the RCU are pressed or the + or buttons on the local keypad.
The picture settings are saved in the image file.
Image 4-14
Brightness
Use the + button for a higher brightness.
Use the - button for a lower brightness.
Contrast
Use the + button for a higher contrast.
Use the - button for lower contrast.
Color
Use the + button for richer colors.
Use the - button for lighter colors.
Tint(Hue)
Tint is only active for Video and S-Video when using the NTSC 4.43 or NTSC 3.58 system.
Use the + button
Use the - button.
38
R5976491 IQ PRO G500 01/02/2007
4. Getting started
Sharpness
Use the + button for a sharper picture.
Use the - button for a softer picture.
Phase
Use the + or - button to adjust the phase.
Gamma
Use the + button for a higher gamma
Use the - button for a lower gamma
Freeze
Press Freeze to freeze the displayed image.
The Pause Key
When the Pause key is pressed, the image projection is stopped, a black screen will be displayed
To restart the image projection:
•
Press PAUSE key
•
Press BACK key
•
Select a source number
4.9
Digital Zoom
What can be done ?
The Digital Zoom key on the RCU allows to zoom (in or out) one particular part of the image
How to Zoom ?
1. Press ← or → on the Digital Zoom key on the remote to Zoom the center of the image
A wizardbox is displayed in the lower part of the screen, follow the instructions.
Use the BACK key to undo the Zoom function.
Digital Zoom can not be performed on a logo.
4.10 Menu structure
PC like menustructure
The projector has a build in "PC like" toolbar menu which allows easy access to different parameters for setting up the projector.
The menu is activated by pressing MENU, it contains 2 levels depending on the type of user:
•
Level 1: standard user
•
Level 2: advanced user, level 2 is password protected, the advanced parameters are only visible when the correct password
has been entered ( factory password = "0000")
Menu items which are not applicable are greyed out.
4.11 Using the menu
Menu Layout
A grey line gives the transition between standard and advanced parameters.
The existence of a submenu is indicated by a white arrow, Settings is a submenu.
Keystone is an item of the Image menu.
R5976491 IQ PRO G500 01/02/2007
39
4. Getting started
Three suspension points indicate that the menuitem hides a dialogbox or a textbox.
Image 4-15
The menus inserted in this manual are of the advanced type: all the items are visible The menus seen by a
standard user on the screen will hence not correspond with the menus in the manual i.e. the advanced items
will not be visible, they will be replaced with "More..."
Greyed out menus or items are not available in this software version
How to pull down a menu ?
1. Use ↓ to pull down a menu
How to pull down a submenu ?
1. Use → to pull down a submenu
How to exit the submenu ?
1. Press BACK to exit a submenu
Press MENU to exit the menu
When the menu has been exited for more than 1 minute, the advanced user password has to be re-entered.
4.12 Using the Dialogboxes
How to use the dialogboxes ?
Some parameters are modified by means of a dialogbox, where selections can be made and/or values can be entered, The values
can be entered in several ways:
Entering numeric values using the numeric keys on the remote control
1. Press ENTER to activate the input field (image 4-16)
2. Key in the desired value
40
R5976491 IQ PRO G500 01/02/2007
4. Getting started
Image 4-16
Entering numeric values using the arrow keys on the remote control
1. Press ENTER to activate the input field.
2. Press ←or → to select the digit to be changed (image 4-17)
3. Press ↓ or ↑ to increase or decrease the value
Image 4-17
Entering numeric values using the arrow keys on the local keypad
1. Press ENTER to activate the input field.
2. Press ←or → to select the digit to be changed
3. Press ↓ or ↑ to increase or decrease the value
To confirm the changes always press ENTER.
Use ↓ or ↑ to browse between the different fields.
In some cases an alphanumeric value (file name, ...) has to be entered. Use ↑ or ↓ to scroll through the character values once the input field is activated
Following characters can be browsed in this particular order:
Decimal scroll list: 0123456789
Signed decimal scroll list: 0123456789ASCII scrolllist:ABCDEFGHIJKLMNOPQRSTUVWXYZ0123456789+-*/&@#.;.abcdefghijklmnopqrstuvwxyz
R5976491 IQ PRO G500 01/02/2007
41
4. Getting started
42
R5976491 IQ PRO G500 01/02/2007
5. Source Selection
5. SOURCE SELECTION
Overview
•
5.1
Source selection
•
Composite Video
•
S-Video
•
The Video Selector
Source selection
Selecting a source
The Source selection menu allows to select one of the different sources. Another method to select an input source is via the remote
control using the numeric keys or by using the local keypad.
When selecting a source with a different resolution (and/or aspect ratio) than the projector’s resolution (and/or
aspect ratio ), the source can be shown in its native resolution or can be re-scaled to the projector’s resolution,
the latter case brings of course some loss of quality.
For more info on resolution match see the Show native resolution function in the Image menu.
How to select a source ?
1. Press MENU to activate the Tool bar
2. Press ↓ to Pull down the Source Selection menu (image 5-1, image 5-2)
3. Use ↑ or ↓ to select one of the different sources ( Press → to Pull down if the item has a submenu)
4. Press ENTER to confirm your choice
On the screen appears now the selected source.
Image 5-1
R5976491 IQ PRO G500 01/02/2007
43
5. Source Selection
Image 5-2
The Barco logo on the menu indicates the presence of a signal, the digit indicates the shortcut key on the
RCU.
The 3 first sources (Data on BNC’s, Component Video & RG(s)B) refer to the 5-cable input, the position of the
indication “1” will always show which BNC configuration is selected.
When to select “Data on BNC’s”
Select Data on BNC’s when a data signal is connected to the BNC’s
When to select “Component video” ?
Select Component video when a video signal of the type (R-Y/Y/B-Y) is connected on the BNC’s.
When to select RG sB Video ?
Select RG sB Video when an RGB video signal (15 KhZ) with Sync on green or sync on H is presented on the BNC’s.
This signal is routed to the video circuit and is projected in a Video Window.
5.2
Composite Video
How to select one of the 7 composite video inputs ?
1. Press MENU to activate the Tool bar
2. Press ↓ to Pull down the Source Selection menu
3. Use ↑ or ↓ to select Composite video
4. Press → to Pull down the submenu
5. Use ↑ or ↓ to select one of the different video inputs (image 5-3)
Note: Video2 is an optional Video input and is only displayed in case the optional Video/Audio layer is installed.
If the extended mode is disabled, the submenu contains only 1 selection (2 selections if the Audio & Video option is
installed).
6. Press ENTER to confirm your choice
A white bullet indicates the selected composite video source which now appears on the screen.
44
R5976491 IQ PRO G500 01/02/2007
5. Source Selection
Image 5-3
Adjustments on a Composite video signal
The projectors allows different adjustments on a composite video signal. Depending on the type of signal (NTSC /PAL) the terminology may differ :
•
Contrast
•
Brightness
•
Color : adjusts the level of color saturation in a PAL signal
•
Tint : adjusts the level of color saturation in an NTSC signal
•
AGC: Automatic Gain Control
The composite video sources can also be selected using the video selector or via the dedicated key 3 on the
RCU. Key 3 allows to browse through the active video inputs when the extended mode is checked in Video
Selector..
5.3
S-Video
When
Select the S-Video input when in presence of a video signal also called S-VHS signal.
An S-Video signal is available on the Mini-Din connector of a camera, VCR or DVD player.
How to select one of the 3 S-Video inputs ?
1. Press MENU to activate the Toolbar
2. Press ↓ to Pull down the Source Selection menu
3. Use ↑ or ↓ to select S-Video
4. Press → to Pull down the submenu
5. Use ↑ or ↓ to select one of the different video inputs (image 5-4)
Note: S-Video4 is an optional Video input and is only displayed in case the optional Video/Audio layer is installed
If the extended mode is disabled, the submenu contains only 1 selection (2 selections if the Audio & Video option is
installed).
6. Press ENTER to confirm your choice
A white bullet indicates the selected video source which now appears on the screen.
R5976491 IQ PRO G500 01/02/2007
45
5. Source Selection
Image 5-4
The S-Video sources can also be selected using the video selector or via the dedicated key 4 on the RCU. Key
4 allows to browse through the active S-Video inputs when the extended mode is checked in Video Selector.
5.4
The Video Selector
Video Selector
The Video Selector is a graphical interface which allows an overview of the different video inputs (Composite Video
and S-Video) and whether they are active (signal connected) or not as well as the selection of these different signals.
Video selector modes
The video selector has two modes:
•
standard mode : the video selectable video inputs are the standard composite video & the S-Video input
•
extended mode : several BNC connections are added and can be selected as video inputs (S-Video inputs).
How to display the Video Selector ?
1. Press MENU to activate the Tool bar
2. Press ↓ to Pull down the Source Selection menu
3. Use ↑ or ↓ to select Video selector
4. Press ENTER
On the screen appears a message, (image 5-5)
followed by a graphical interface (image 5-6, image 5-7)
A BNC or S-Video connector on the video selector can be in one of following conditions:
-
A: connector disabled
-
B: connector enabled but inactive (no video signal present on connector)
-
C: connector enabled & active (video signal present on connector
-
D: connector enabled active & selected
-
E: connector enabled & active & focused (browser positioned on connector)
MESSAGE
Scanning video inputs
Please wait ...
Image 5-5
46
R5976491 IQ PRO G500 01/02/2007
5. Source Selection
A
A
B
B
C
C
D
E
D
E
Image 5-7
Image 5-6
If the Audio/Video option is installed the Video Selector is updated with the additional Video & S-Video input
Image 5-8
How to select an input on the Video Selector ?
1. Use ←or→ to browse through the different inputs
2. Press ENTER
Use MENU or BACK to exit the Video Selector
How to disable the extended Video Selector
1. Use the arrow keys to select the Extended checkbox
2. Press ENTER to disable the extended mode
The standard Video Selector is displayed (image 5-9)
R5976491 IQ PRO G500 01/02/2007
47
5. Source Selection
Image 5-9
48
R5976491 IQ PRO G500 01/02/2007
6. General Menu
6. GENERAL MENU
Overview
•
6.1
Pause
•
Freeze
•
Standby Timer
•
Audio (Optional)
•
Identification
Pause
Interrupting the image projection
With the Pause function, the image projection can be stopped, the projector remains with full power for immediate restart. The
projection is interrupted by means of a mechanical shutter cutting the light beam.
How to interrupt the image projection ?
1. Press MENU to activate the Tool bar
2. Press → to select General
3. Press ↓ to Pull down the General menu
4. Use ↑ or ↓ to select Pause (image 6-1)
5. Press ENTER to activate the Pause function
A brief sound indicates that the shutter has been activated.
Image 6-1
The image projection can also be interrupted using the PAUSE key on the RCU.
To restart the image : press PAUSE
6.2
Freeze
Freezing the image
With the Freeze function, the image can be frozen. To restart the image, reuse the Freeze function or press the FREEZE button on
the remote.
How to freeze the image ?
1. Press MENU to activate the Tool bar
2. Press → to select General
3. Press ↓ to Pull down the General menu
4. Use ↑ or ↓ to select Freeze (image 6-2)
5. Press ENTER to activate the Freeze function
R5976491 IQ PRO G500 01/02/2007
49
6. General Menu
Image 6-2
The image can also be frozen using the FREEZE key on the RCU
6.3
Standby Timer
Purpose of the Standby Timer
If there is no signal, and the standby timer is enabled, a dialogbox is displayed and the projector will shut down after a determined
time.
The countdown time can be set in a dialog box in a range from 180 to 3600 seconds (default value = 300). The Timer can also be
disabled.
How to enable the timer ?
1. Press MENU to activate the Tool bar
2. Press → to select General
3. Press ↓ to Pull down the General menu
4. Use ↑ or ↓ to select Standby Timer (image 6-3)
5. Press ENTER to activate the function
On the screen appears a dialogbox (image 6-4)
6. Use ↑ or ↓ to select Enabled, a box surrounds the selected item, press ENTER to activate
7. Use ↑ or ↓ to browse to the input field
8. Use ←or→ , the numeric keys on the remote or the keypad to change the countdown setting
9. Press MENU or BACK to exit or to go back to the previous menu
Image 6-3
50
R5976491 IQ PRO G500 01/02/2007
6. General Menu
Image 6-4
6.4
Audio (Optional)
Overview
•
Audio Setup
•
Audio Settings
6.4.1
Audio Setup
What can be done ?
Layer 3 allows the input of 4 audio signals, each of them can be linked to the corresponding (video or data) source signal. it is also
possible to link multiple audio signals to one video (or data) source signal, this can be useful in case of teleconferencing.
The configuration has to be done in the Audio Setup menu
Starting the Audio Setup menu
1. Press MENU to activate the Tool bar
2. Press → to select General
3. Press ↓ to Pull down the General menu
4. Use ↑ or ↓ to select Audio setup (image 6-5)
5. Press ENTER
A dialog box is displayed (image 6-6)
-
LED is red : audio input is mute
-
LED is green : input is active (linked image source is selected)
-
LED is orange : image source is not selected
Image 6-5
R5976491 IQ PRO G500 01/02/2007
51
6. General Menu
Image 6-6
How to mute an Audio channel ?
1. use the arrow keys to select the desired mute box
2. Press ENTER
How to link an audio input to a source ?
1. use the arrows to select the desired scroll box
2. Press ENTER to open the scroll box
3. use ↑ or ↓ to select the source
4. Press ENTER
When the source switching mode is the fade in/out mode, the audio switching will also be done using a fade
in/out effect.
6.4.2
Audio Settings
Audio Settings
1. Press MENU to activate the Tool bar
2. Press → to select General
3. Press ↓ to Pull down the General menu
4. Use ↑ or ↓ to select Audio setup (image 6-7)
5. Press ENTER
A dialog box is displayed (image 6-8)
6. Use the arrow keys to select and change the settings
Note: The default value for the volume is 43, this corresponds to a gain factor of 1 (volume in = volume out).
Image 6-7
52
R5976491 IQ PRO G500 01/02/2007
6. General Menu
Image 6-8
6.5
Identification
The projector’s identification screen
The identification screen displays the projector’s main characteristics
How to display the identification screen ?
1. Press MENU to activate the Tool bar
2. Press → to select General
3. Press ↓ to Pull down the General menu
4. Use ↑ or ↓ to select Identification (image 6-9)
5. Press ENTER to activate the function
On the screen appears a text box.
In this case the projector is an iDR500 (image 6-10)
6. Press MENU or BACK to exit or to go back to the previous menu
Image 6-9
R5976491 IQ PRO G500 01/02/2007
53
6. General Menu
Image 6-10
54
R5976491 IQ PRO G500 01/02/2007
7. Image Menu
7. IMAGE MENU
Overview
•
Settings
•
Aspect ratio
•
Show native resolution
•
Keystone
•
Color temperature
•
Filmmode detection
•
Blanking
•
Input balance
•
AGC on Video
•
Manual Gain Control
7.1
Settings
Overview
•
Contrast
•
Brightness
•
Color
•
Tint (hue)
•
Sharpness
•
Gamma
•
Phase
•
Noise reduction
What can be done ?
Correct image settings are important for a good image reproduction. The image settings are made through a dialog box with a scroll
bar. Minimal, maximal and actual values are indicated. These settings can also be done directly via the RCU’s dedicated buttons,
except for the sharpness.
Image 7-1
Image 7-2
R5976491 IQ PRO G500 01/02/2007
55
7. Image Menu
7.1.1
Contrast
Contrast adjustment
Adjust the contrast to “brighten” the white parts of the image.
It is recommended to adjust the brightness before adjusting the contrast.
How to change the contrast
1. Press MENU to activate the Toolbar
2. Press → to select the Image item
3. Press ↓ to Pull down the Image menu
4. Use ↑ or ↓ to select settings
5. Press → to pull down the menu
6. Use ↑ or ↓ to select Contrast
7. Press ENTER
On the screen appears now a sliderbox (image 7-3)
8. Use ←or → , the numeric keys on the remote, or the keypad to change the contrast
Image 7-3
7.1.2
Brightness
Brightness adjustment
Adjusting the brightness will affect the dark areas of the image. Increase the brightness to “lighten” up the parts that are too dark.
How to change the Brightness ?
1. Press MENU to activate the Toolbar
2. Press → to select the Image item
3. Press ↓ to Pull down the Image menu
4. Use ↑ or ↓ to select settings
5. Press → to pull down the menu
6. Use ↓ or ↑ to select Brightness
7. Press ENTER
On the screen appears now a sliderbox (image 7-4)
8. Use ←or → , the numeric keys on the remote, or the keypad to change the Brightness
Image 7-4
7.1.3
Color
Color adjustment
Adjust the color to obtain more or less saturated colors.
56
R5976491 IQ PRO G500 01/02/2007
7. Image Menu
How to change the Color ?
1. Press MENU to activate the Toolbar
2. Press → to select the Image item
3. Press ↓ to Pull down the Image menu
4. Use ↑ or ↓ to select settings
5. Press → to pull down the menu
6. Use ↓ or ↑ to select Color
7. Press ENTER
On the screen appears now a sliderbox (image 7-5)
8. Use ←or → , the numeric keys on the remote, or the keypad to change the Color
Image 7-5
7.1.4
Tint (hue)
How to change the Tint ?
1. Press MENU to activate the Toolbar
2. Press → to select the Image item
3. Press ↓ to Pull down the Image menu
4. Use ↑ or ↓ to select settings
5. Press → to pull down the menu
6. Use ↓ or ↑ to select Tint
7. Press ENTER
On the screen appears now a sliderbox
8. Use ←or → , the numeric keys on the remote, or the keypad to change the Tint
7.1.5
Sharpness
How to change the sharpness ?
1. Press MENU to activate the Toolbar
2. Press → to select the Image item
3. Press ↓ to Pull down the Image menu
4. Use ↑ or ↓ to select settings
5. Press → to pull down the menu
6. Use ↓ or ↑ to select sharpness
7. Press ENTER
On the screen appears now a sliderbox
8. Use ←or → , the numeric keys on the remote, or the keypad to change the sharpness
7.1.6
Gamma
How to change the Gamma
1. Press MENU to activate the Toolbar
2. Press → to select the Image item
3. Press ↓ to Pull down the Image menu
4. Use ↑ or ↓ to select settings
R5976491 IQ PRO G500 01/02/2007
57
7. Image Menu
5. Press → to pull down the menu
6. Use ↓ or ↑ to select Gamma
7. Press ENTER
On the screen appears now a sliderbox
8. Use ←or → , the numeric keys on the remote, or the keypad to change the Gamma
7.1.7
Phase
Phase adjustment
A bad phase adjustment will result in bad transitions and sometimes noise (text can end to be unclear).
How to change the Phase ?
1. Press MENU to activate the Toolbar
2. Press → to select the Image item
3. Press ↓ to Pull down the Image menu
4. Use ↑ or ↓ to select settings
5. Press → to pull down the menu
6. Use ↓ or ↑ to select Phase
7. Press ENTER
On the screen appears now a sliderbox (image 7-6)
8. Use ←or → , the numeric keys on the remote, or the keypad to change the Phase
Image 7-6
7.1.8
Noise reduction
How to change the Noise reduction ?
1. Press MENU to activate the Toolbar
2. Press → to select the Image item
3. Press ↓ to Pull down the Image menu
4. Use ↑ or ↓ to select settings
5. Press → to pull down the menu
6. Use ↓ or ↑ to select Noise reduction
7. Press ENTER
On the screen appears now a sliderbox
8. Use ←or → , the numeric keys on the remote, or the keypad to change the Noise reduction setting.
7.2
Aspect ratio
Aspect ratios
The standard aspect ratio used in broadcast television is the 4:3 ratio. However, most of the DVD sources use nowadays the
widescreen 16:9 or even the cinemascope 2.35:1 aspect ratio.
Some DVD sources may even use the anamorphic 16:9 or anamorphic 2.35:1 to take advantage of the higher vertical resolution
offered by the 4:3 ratio. The “anamorphic” term means that the original widescreen image is squeezed in order to fit the 4:3 aspect
ratio.
58
R5976491 IQ PRO G500 01/02/2007
7. Image Menu
4:3
16:9
2.35:1
Image 7-7
Common non- anamorphic aspect ratios in DVD sources
16:9
2.35:1
Image 7-8
Anamorphic aspect ratios in DVD sources
What can be done ?
The aspect ratio setting forces the projector to project an image using a defined aspect ratio :
•
4:3
•
16:9
•
5:4
•
Auto
The settings do not refer to the aspect ratio of the source !
R5976491 IQ PRO G500 01/02/2007
59
7. Image Menu
Projector setting
Source
4:3
4:3
16:9
5:4
16:9
2.35:1
16:9 anamorphic
2.35:1 anamorphic
Image 7-9
Possible aspect ratio settings and their effect on different sources in the iQ.
We can conclude that the thumb rule for DVD projection is to always leave the projector in 4:3 format except when dealing with
anamorphic sources where the 16:9 setting allows the best reproduction.
The Auto function calculates an aspect ratio based on the information stored in the image files.
Selecting Auto in case of a Video source may shrink the image horizontally
How to change the Aspect ratio ?
1. Press MENU to activate the Tool bar
2. Press → to select Image
3. Press ↓ to Pull down the Image menu (image 7-10)
4. Use ↑ or ↓ to select Aspect ratio
5. Use → open the Aspect ratio menu
6. Use ↑ or ↓ to select the desired ratio
7. Press ENTER to confirm
60
R5976491 IQ PRO G500 01/02/2007
7. Image Menu
Image 7-10
The aspect ratio settings are greyed out in case the Show native resolution or the Full screen representation
setting is enabled.
How to set a custom Aspect ratio ?
1. Press MENU to activate the Tool bar
2. Press → to select Image
3. Press ↓ to Pull down the Image menu (image 7-11)
4. Use ↑ or ↓ to select Aspect ratio
5. Use → open the Aspect ratio menu
6. Use ↑ or ↓ to select Custom
7. Press ENTER to confirm
A dialog box is displayed (image 7-12)
8. Enter the values for width and height of the image
The image aspect ratio is updated.
Image 7-11
R5976491 IQ PRO G500 01/02/2007
61
7. Image Menu
Image 7-12
7.3
Show native resolution
Graphics
Native resolution of the LCD panels = 1024 pixels x 768 pixels (4:3)
Reality(SXGA)
Native resolution of the LCD panels = 1366 pixels x 1024 pixels (4:3)
Reality(SXGA+)
Native resolution of the LCD panels = 1400 x 1050 pixels (4:3)
What can be done ?
The aim here is to always show the resolution of the source independently of the resolution of the LCD panels. This way better
image reproduction is obtained since no up or down scaling is done on the source.
Note that native resolution refers here to the source and does thus only have sense when handling data sources (greyed out for
video sources).
Depending on the type of projector the “show native resolution” function will handle the sources as follows:
Projected image
Source
Name
Ratio
Resolution
Ratio
Resolution
Particularities Reality
(SXGA+)
Particularities
Graphics
xga
4:3
1024x768
4:3
1024x768
image centered +side
blanked
image centered
sxga
5:4
1280x1024
5:4
1280x1024
image centered +side
blanked
scroll image
sxga+
4:3
1400x1050
4:3
1400x1050
image centered
scroll image
uxga
4:3
1600x1200
4:3
1600x1200
scroll image
scroll image
Table 7-1
Show native resolution = ON in case of a Graphics(XGA) and Reality (SXGA+) iQ Pro projector
The Full screen representation function on the other hand forces to use the complete native resolution of the
LCD panels.
How to enable the “Show native resolution” function?
1. Press MENU to activate the Toolbar
2. Press → to select the Image item
3. Press ↓ to Pull down the Image menu
62
R5976491 IQ PRO G500 01/02/2007
7. Image Menu
4. Use ↑ or ↓ to select Show native resolution (image 7-13)
5. Press → to pull down the menu
6. Use ↓ or ↑ to select On
7. Press ENTER
A white bullet shows the selection
Image 7-13
The default mode is used if the show native resolution and the full screen function are off.
The default mode shows always the native ratio and forces the native resolution of the panels (part of the
image blanked where needed)
When show native resolution is ON and the resolution of the source is higher than the panel resolution , use
the arrow keys to scroll through the image (pan).
7.4
Keystone
What can be done ?
The Keystone adjustment is used to align the image, this can be necessary when projecting under a non standard angle
How to perform a Keystone correction ?
1. Press MENU to activate the Tool bar
2. Press → to select Image
3. Press ↓ to Pull down the Image menu
4. Use ↑ or ↓ to select Keystone (image 7-14)
5. Press ENTER to confirm
A sliderbox is displayed . (image 7-15)
Use ← or →, the numeric keys on the remote, or the keypad to adjust the keystone.
The Top and bottom adjustments affect the image differently. (image 7-16, image 7-17)
R5976491 IQ PRO G500 01/02/2007
63
7. Image Menu
Image 7-14
Image 7-15
Image 7-16
Top adjustment of the keystone
Image 7-17
Bottom adjustment of the keystone
7.5
Color temperature
What can be done ?
The color temperature can be selected according to the type of source:
There are 4 different preset color temperatures:
•
Projector white
•
computer : 9300 K
•
Video : 6500 K
•
Film : 5400 K
•
Broadcast : 3200 K
These calibrated presets can be selected and will provide optimum color tracking, the projector allows however the setting of a
personal color temperature, this is done in custom
How to select a preset color temperature ?
1. Press MENU to activate the Tool bar
2. Press → to select the Image item
3. Press ↓ to Pull down the Image menu
64
R5976491 IQ PRO G500 01/02/2007
7. Image Menu
4. Use ↑ or ↓ to select Color temperature
5. Press → to pull down the menu
6. Use ↓ or ↑ to select the desired preset color temperature
7. Press ENTER
The color temperature of the image is adapted and a white bullet shows the active setting.
How to start up the custom color temperature ?
1. Press MENU to activate the Tool bar
2. Press → to select the Image item
3. Press ↓ to Pull down the Image menu
4. Use ↑ or ↓ to select Color temperature
5. Press → to pull down the menu
6. Use ↓ or ↑ to select custom
7. Press ENTER
A slider box for the red custom setting is displayed as well as a wizard text box in the lower part of the screen. (image 7-18,
image 7-19)
Follow the instructions on the wizard textbox. (image 7-20)
Image 7-18
Image 7-19
Image 7-20
7.6
Filmmode detection
What can be done ?
Some sources like common DVD material are derived from cinema 24 Hz sources (2/2 or 3/2 pull down method).
R5976491 IQ PRO G500 01/02/2007
65
7. Image Menu
NTSC VIDEO
VIDEO PAL
50f/s
167
FILM
24 f/s
60 f/s
167
160
133
125
120
80
83
83
1/30s
50
40
42
1/20s
0
0
2/2
3/2
Image 7-21
film to video conversion: 2/2 and 2/3 pull down method
The filmmode detection insures that these converted signals are shown without artefacts, especially motion artefacts due to bad
de-interlacing.
Image 7-22
This function may cause undesired effects on standard sources, therefore it can be disabled (OFF) at any time
Enabling/disabling the filmmode detection
1. Press MENU to activate the Toolbar
2. Press → to select the Image item
3. Press ↓ to Pull down the Image menu
4. Use ↑ or ↓ to select Filmmode detection
5. Press → to pull down the menu
6. Use ↓ or ↑ to enable or disable the Filmmode detection
7. Press ENTER
A white bullet shows the active setting (image 7-23)
66
R5976491 IQ PRO G500 01/02/2007
7. Image Menu
Image 7-23
7.7
Blanking
Blanking in the Image menu
The blanking in general allows to blank unwanted video information (noise in the top or bottom of the image).
The blanking in the image menu is the same as in the Display settings menu except for the fact that here the blanking settings are
stored in the image files. In other words each custom file or source has its own blanking values.
See the blanking procedure in the Display settings menu.
If the selected source is not entirely displayed always check first the blanking settings in the image menu
since the active custom file may contains blanking.
7.8
Input balance
Introduction: Unbalanced color signals
When transporting signals, there is always a risk of deterioration of the information contained in the signals.
In case of information contained in the amplitude of the signals which is the case of data color signals (R, G, B),image 7-24 ,we are
quite sure that the amplitude of these color signals is subject to alterations.
An example of alteration may be a DC component added to the signal, in the form of a DC offset repositioning the black level, since
this black level (“brightness”) will become crucial later on ( clamping circuit) it will result in “black not being black”.
Another value that is subject to alteration is the amplitude of the signal, resulting in an altered “Gain” of the signal (“white level” or
contrast ).
The alterations of the three color signals will happen independently i.e. the colors will end to be unbalanced, image 7-25
B
0.7V
Black level
Image 7-24
R5976491 IQ PRO G500 01/02/2007
67
7. Image Menu
G
B
R
∆G
∆R
∆Β
Black level
Image 7-25
One can conclude here that a good color tracking can only be met by using three previously (input) balanced
color signals
Analog Digital Conversion
The analog color signals must pass through an Analog/Digital conversion circuit prior to any digital processing in the PMP.
A typical ADC transforms the analog value into an 8 bit coded digital signal.
The graphic shows that when converting a signal containing a DC offset component the range of the converter is not optimally used.
ADC
R
255
i2 : video information
∆
0
i1 : superfluous information
Black level
Image 7-26
One can conclude here that a good data conversion can only be met by using three previously (input) balanced
color signals
The objective of input balancing
The objective in input balancing is to “set” the same black level and the same white level for the three colors of a particular input
source.
Black level setting : brightness
White level setting : contrast
The same absolute black and white level for the three colors allows the same reference for Brightness and contrast control of the
picture !
These two references also set the range in which the ADC will work for that particular source ( this explains also why each input
balance setting is linked to a particular source and thus saved in the image file).
How can it be done ?
To balance the three color signals of a particular source there are conditions; in fact we must know the black and the white level of
the source i.e. :
68
1.
the source in question must be able to generate a white signal, ideally a 100% white (background) full screen pattern
2.
the source in question must be able to generate a black signal, ideally a 100 % black (background) full screen pattern
R5976491 IQ PRO G500 01/02/2007
7. Image Menu
B
A
Image 7-27
White balance : In the projector, we will set the contrast for each color until we get a 100% light output picture when projecting a
100% white image (image A)
Black balance : In the projector, we will set the brightness for each color until we get a 0% light output picture when projecting a
100% black image (image B).
The changeover from min to max is indicated by the apparition of bright spots also called “digital noise”
An alternative to a full screen White/black pattern is the standard gray scale pattern, the white bar will be used
for white balance and the black bar for black balance.
Image 7-28
Black balance
1. Press MENU to activate the Toolbar
2. Press → to select the Image item
3. Press ↓ to Pull down the Image menu
4. Use ↑ or ↓ to select Input balance
5. Press → to pull down the menu
6. Use ↓ or ↑ to select Black balance (image 7-29)
7. adjust the red black level on a minimal value (image 7-30, image 7-31)
8. adjust the blue black level on a minimal value
Note: this minimal value is not necessary , provided that the 2 other colors are not influencing too much the color to be adjusted,
in fact the aim is to minimize the effect of the two other colors since there is a risk of reaching too soon the 50% transition
due to the contribution of these two other colors signals.
9. Adjust the green black level until bright spots appear on the screen
10.adjust the blue black level on a minimal value
Note: this minimal value is not necessary , provided that the 2 other colors are not influencing too much the color to be adjusted,
in fact the aim is to minimize the effect of the two other colors since there is a risk of reaching too soon the 50% transition
due to the contribution of these two other colors signals.
11. Adjust the green black level until bright spots appear on the screen
12.Adjust the Blue black level until bright spots appear on the screen
13.Adjust the red black level until bright spots appear on the screen
the projected image should know be noisy full black
R5976491 IQ PRO G500 01/02/2007
69
7. Image Menu
Image 7-29
Image 7-30
Image 7-31
Performing White input balance
1. Connect the source you want to project
2. Select a white pattern (or gray scale as alternative)
3. Press MENU to activate the Toolbar
4. Press → to select the Image item
5. Press ↓ to Pull down the Image menu
6. Use ↑ or ↓ to select Input balance
7. Press → to pull down the menu
8. Use ↓ or ↑ to select White balance (image 7-32)
9. adjust the red white level (gain) on a minimal value (image 7-33)
10.adjust the blue white level (gain) on a minimal value
Note: this minimal value is not necessary , provided that the 2 other colors are not influencing too much the color to be adjusted,
in fact the aim is to minimize the effect of the two other colors since there is a risk of reaching too soon the transition
(bright spots) due to the contribution of these two other colors signals.
11. Adjust the Green white level (gain) until bright spots appear on the screen
12.Adjust the Blue white level (gain) until bright spots appear on the screen
13.Adjust the Red white level (gain) until bright spots appear on the screen
the projected image should know be noisy neutral grey.
70
R5976491 IQ PRO G500 01/02/2007
7. Image Menu
Image 7-32
Image 7-33
if one uses a gray scale pattern, the bright spots should appear in the white bar.
Selecting Preset restores the factory input balance setting
Remark on the input balance of a component video source
Before starting the Input Balance procedure, generate a signal with dominant white parts.
Input balance is also available for a component video source under following conditions:
•
A component video signal is present on the BNC’s
•
”Data on BNC’s” is selected in the Source selection menu
•
Cr/Y/Cb is selected in the Advanced menu of the corresponding image file
The procedure is the same as for a data source except:
R5976491 IQ PRO G500 01/02/2007
71
7. Image Menu
•
The white balance happens only on Green
Adjust until bright spots appear in the image
Image 7-34
•
The black balance happens on the three colors
The PR and PB connector have to be removed from the input
Adjust until noise appears in the image
Image 7-35
The input balance settings are stored in the image file, each source has its own input balance.
7.9
AGC on Video
AGC
Automatic Gain Control: allows an automatic amplitude (gain) control of the incoming video signal
AGC is only for Video signals
Enabling/disabling the AGC
1. Press MENU to activate the Tool bar
2. Press → to select the Image item
3. Press ↓ to Pull down the Image menu
4. Use ↑ or ↓ to select AGC on Video
5. Press → to pull down the menu
6. Use ↓ or ↑ to enable or disable the AGC
7. Press ENTER
A white bullet shows the active setting (image 7-36)
72
R5976491 IQ PRO G500 01/02/2007
7. Image Menu
Image 7-36
The AGC can be disturbing in case of Macrovision encoded signals, therefore the AGC can be disabled (OFF)
at any time
7.10 Manual Gain Control
What can be done ?
Beside the AGC there is the possibility to manually set the gain of the incoming video signal. When the AGC is enabled (ON), the
manual setting does not affect the gain, AGC must therefore be disabled. The manual gain control must be done on an external
pattern with white areas (grey scale bar pattern)
How to set the Manual Gain Control ?
1. Press MENU to activate the Tool bar
2. Press → to select the Image item
3. Press ↓ to Pull down the Image menu
4. Use ↑ or ↓ to select Manual Gain Control (image 7-37)
5. Press ENTER
A scroll bar is displayed (image 7-38)
6. Use ← or →, the numeric keys on the remote, or the keypad to change the gain so as to obtain homogene white parts in the
image.
Image 7-37
R5976491 IQ PRO G500 01/02/2007
73
7. Image Menu
Image 7-38
74
R5976491 IQ PRO G500 01/02/2007
8. Tools Menu
8. TOOLS MENU
Overview
•
Introduction to PiP
•
PiP select
•
PiP add window
•
PiP remove window
•
PiP layout
•
PiP Adjust
•
Diagnostics
8.1
Introduction to PiP
PiP
PiP stands for "Picture in Picture" and allows to display multiple windows containing each of them an image. The
windows may be of the video or data type.
What are the different possibilities within the PiP mode ?
The input section of the IQ projector allows a multitude of combinations of different input signals which may be projected in the 4
windows of the PiP screen.
The PiP mode allows independent settings for each window:
•
Image settings : contrast, brightness, tint, color,...
•
Vertical and horizontal shift of each window all over the screen
•
Resizing of the window
•
Digital Zoom
•
Linking of (an) audio input(s) to a single or multiple windows
R5976491 IQ PRO G500 01/02/2007
75
8. Tools Menu
What are the different PiP layouts ?
•
Full screen2
The full screen is used to display one of the selected sources.
Browsing through the sources is possible with the PiP Adjust button on the remote.
•
2–by-2 raster2
The screen is divided into 4 subscreens containing 2 Video and 2 Data sources.
Image 8-1
PiP: 2by2 layout
•
PiP layout 1–3
3
These are factory layouts, they can be edited and saved.
•
Personal layouts
Beside the 2 fixed layouts and the 3 factory layouts, one can set 5 additional (personal) layouts.
PiP dedicated buttons
•
PiP Adjust : this button allows to focus on one particular window, this is shown with a white frame surrounding the selected
window.
A source identification box is displayed in the right lower corner.
Image 8-2
Pressing the button removes the frame to the next window. This can also be done via PiP Adjust in the Tools menu
•
PiP: this button allows to browse through the different configurations, it has the same function as PiP select in the Tools menu.
Since there is only one decoder (second decoder is optional), when in 2by2 configuration, Video1 and Video2
are derived from the same video source.
2. fixed layout
3. factory layouts
76
R5976491 IQ PRO G500 01/02/2007
8. Tools Menu
8.2
PiP select
PiP layouts
The different PiP layouts (configurations) can be selected in the PiP select menu.
How to change the PiP configuration ?
1. Press MENU to activate the Tool bar
2. Press → to select the Tools item
3. Press ↓ to Pull down the Tools menu
4. Use ↑ or ↓ to select PiP select
5. Press → to pull down the menu
6. Use ↑ or ↓ to select the desired configuration
7. Press ENTER
A white bullet shows the active layout (image 8-3)
Image 8-3
The PiP configuration can also be selected via the dedicated PiP key on the RCU.
8.3
PiP add window
What can be done ?
It is possible to add a window to the existing windows (maximum 4), therefore a source must be selected.
Sources which are already used are non selectable. If, for instance, the PiP layout contains a component video then component
video will be non selectable.
Once added, the window may be altered in several ways to meet particular needs:
•
repositioning
•
re-sizing
•
changing the order
How to add a window ?
1. Press MENU to activate the Tool bar
2. Press → to select the Tools item
3. Press ↓ to Pull down the Tools menu
4. Use ↑ or ↓ to select PiP add window (image 8-4)
5. Press ENTER
The source selection menu is displayed (image 8-5)
In the lower part of the screen appears a wizard in 4 steps (image 8-6)
R5976491 IQ PRO G500 01/02/2007
77
8. Tools Menu
Image 8-4
Image 8-5
Image 8-6
8.4
PiP remove window
How to remove a window ?
1. Press MENU to activate the Tool bar
2. Press → to select the Tools item
3. Press ↓ to Pull down the Tools menu
4. Use ↑ or ↓ to select PiP remove window (image 8-7)
5. Press ENTER
In the lower part of the screen appears a wizard. (image 8-8)
The selected window appears surrounded with a white frame, each hit on PiP ADJUST will move the frame along the different
windows.
Image 8-7
78
R5976491 IQ PRO G500 01/02/2007
8. Tools Menu
Image 8-8
8.5
PiP layout
Overview
•
8.5.1
PiP Save
•
PiP rename layout
•
PiP delete layout
PiP Save
What can be done ?
The active layout can be saved or "saved as".
When a new layout is saved it is added to the PiP select menu.
A fixed layout can be edited (re-sizing, re-positioning,...) but it can not be saved under its original name.
How to save a layout ?
1. Press MENU to activate the Tool bar
2. Press → to select the Tools item
3. Press ↓ to Pull down the Tools menu
4. Use ↑ or ↓ to select PiP layout
5. Press → to pull down the menu
6. Use ↑ or ↓ to select PiP save or save as (image 8-9)
7. Press ENTER
If save as has been selected, a dialog box is displayed (image 8-10)
Use ← or →, the numeric keys on the remote, or the keypad to enter the name and exit with BACK or MENU.
If save as has been selected, a message box is displayed (image 8-11)
Image 8-9
Image 8-10
R5976491 IQ PRO G500 01/02/2007
Image 8-11
79
8. Tools Menu
8.5.2
PiP rename layout
What can be done ?
The non fixed layouts (factory and personal layouts) can be renamed .
The maximal length of the name is 12 characters.
A fixed layout can not be renamed
How to rename a layout ?
1. Press MENU to activate the Tool bar
2. Press → to select the Tools item
3. Press ↓ to Pull down the Tools menu
4. Use ↑ or ↓ to select PiP layout
5. Press → to pull down the menu
6. Use ↑ or ↓ to select Rename
7. Press ENTER
A dialog box is displayed (image 8-12)
8. Use ↑ or ↓ to select the layout to be renamed
9. Press ENTER
A dialog box is displayed (image 8-13)
Use ← or →, the numeric keys on the remote, or the keypad to enter the name and exit with BACK or MENU.
Image 8-13
Image 8-12
8.5.3
PiP delete layout
What can be done ?
The non fixed layouts (factory and personal layouts) can be deleted.
The fixed layouts and the active layout can not be deleted
How to delete a layout ?
1. Press MENU to activate the Tool bar
2. Press → to select the Tools item
3. Press ↓ to Pull down the Tools menu
80
R5976491 IQ PRO G500 01/02/2007
8. Tools Menu
4. Use ↑ or ↓ to select PiP layout
5. Press → to pull down the menu
6. Use ↑ or ↓ to select Delete
7. Press ENTER
A dialog box is displayed (image 8-14)
8. Use ↑ or ↓ to select the layout to be renamed
9. Press ENTER
The layout is deleted and disappears from the dialog box
Image 8-14
8.6
PiP Adjust
What can be done ?
PiP adjust allows to browse through the windows in the active layout, a white frame indicates the window which has the focus.
This way, independent settings (picture settings, ...) are possible for each window.
This can also be done by using the dedicated PiP Adjust key on the RCU
Image 8-15
PiP adjust in case of 2by2 layout
A
B
Data1 window has the focus, new settings will only affect Data1 window
Video1 window has the focus, new settings will only affect Video1 window
PiP adjust
1. Press MENU to activate the Toolbar
R5976491 IQ PRO G500 01/02/2007
81
8. Tools Menu
2. Press → to select the Tools item
3. Press ↓ to Pull down the Tools menu
4. Use ↑ or ↓ to select PiP Adjust (image 8-16)
5. Press ENTER
The menu dissapears.
The focus moves to the next window when pressing ENTER (clockwise rotation)
If you press BACK or if you wait 5 seconds the menu is displayed.
Image 8-16
When using the PiP adjust key on the RCU the corresponding source box is displayed in the bottom right
corner.
How to adjust a window in the layout ?
1. Use the PiP Adjust key or function in the menu to choose the window to be adjusted
2. Press ENTER
A wizard bar is displayed in the bottom of the screen
Follow the procedure.
8.7
Diagnostics
What can be done ?
The I 2C bus allows the diagnostic of different hardware components
How to display the diagnostics menu ?
1. Press MENU to activate the Toolbar
2. Press → to select the Tools item
3. Press ↓ to Pull down the Tools menu
4. Use ↑ or ↓ to select Diagnostics
5. Press → to pull down the menu
6. Press ENTER to select I 2C (image 8-17)
A textbox is displayed (image 8-18, image 8-19)
82
R5976491 IQ PRO G500 01/02/2007
8. Tools Menu
Image 8-17
I2C diagnostics
Device
Slave address
fpga backplane1
fpga backplane2
fpga backplane3
ADC layer1
ADC layer2
ADC layer3
Serial eeprom DVI layer2
Serial eeprom DVI layer3
Video decoder
Video indicator
Video Processor
Motor driver
Lamp driver
Image 8-18
Image 8-19
R5976491 IQ PRO G500 01/02/2007
83
8. Tools Menu
84
R5976491 IQ PRO G500 01/02/2007
9. Signal Menu
9. SIGNAL MENU
Overview
9.1
•
Switching mode
•
Background
Switching mode
Switching from one source to another
To minimize undesired effects when switching from one source to another, one can use the Seamless switching mode, beside Seamless switching there is a wide choice of several effects which render the source switching transitions more enjoyable.
How to select a switching mode ?
1. Press MENU to activate the Tool bar
2. Press → to select the Signal item
3. Press ↓ to Pull down the Signal menu
4. Use ↑ or ↓ to select Switching mode
5. Press → to pull down the menu
6. Use ↑ or ↓ to select the desired switching mode (image 9-1)
7. Press ENTER
A white bullet shows the active effect.
The next source switching will be done using the selected effect
Image 9-1
The Random mode will select a new switching mode at each source switching i.e. there will never be 2 successive source switchings with the same effect.
The Seamless switching mode is not used in the Random mode.
The switching effects are only possible in the full screen mode
R5976491 IQ PRO G500 01/02/2007
85
9. Signal Menu
When the source switching mode is the fade in/out mode, the audio (when available) switching will also be
done using a fade in/out effect.
9.2
Background
Purpose
If there is no signal connected to the projector, the background will be a logo, a black or a blue screen depending on the background
settings.
How to change the background ?
1. Press MENU to activate the Toolbar
2. Press → to select the Signal item
3. Press ↓ to Pull down the Signal menu
4. Use ↑ or ↓ to select Background
5. Press → to pull down the menu
6. Use ↑ or ↓ to select the desired background (image 9-2)
7. Press ENTER
Image 9-2
The logo display is only possible in the full screen mode, a logo can thus not be displayed (rescaled) in a
window in the PiP mode.
When there is no signal connected, the projector will also start its standby timer countdown (if enabled) and
shuts down after the predetermined time.
86
R5976491 IQ PRO G500 01/02/2007
10. Lamp Menu
10. LAMP MENU
Overview
•
Runtimes
•
Mode
•
Power mode (only active in the iQG/R 500)
•
History
•
Reset runtime
•
Runtime warning
10.1 Runtimes
How to display the lamp runtimes ?
1. Press MENU to activate the Toolbar
2. Press → to select the Lamp item
3. Press ↓ to Pull down the Lamp menu
4. Use ↑ or ↓ to select Runtimes (image 10-1)
5. Press ENTER
A textbox is displayed (image 10-2)
Image 10-1
Image 10-2
10.2 Mode
What are the different lamp modes ?
Single mode
R5976491 IQ PRO G500 01/02/2007
87
10. Lamp Menu
The projector will always switch to the lamp with the shortest runtime when the difference between the runtimes of lamp1 and lamp
2 reaches 100 hours, switching from one lamp to another happens only at switching on of the projector and not during operation.
When the lamp fails or reaches its maximum runtime the projector switches automatically to the other lamp without interrupting the
projection.The failure is logged and the lamp will never be initialized in the future.
Image 10-3
Single mode operation: switching principle
Dual mode
Both lamps are working.
When one lamp fails, the projector continues the projection using the remaining lamp.
How to select the lamp mode ?
1. Press MENU to activate the Toolbar
2. Press → to select the Lamp item
3. Press ↓ to Pull down the Lamp menu
4. Use ↑ or ↓ to select Mode
5. Press → to pull down the menu
6. Use ↑ or ↓ to select the desired background (image 10-4)
7. Press ENTER
A bullet shows the active mode.
88
R5976491 IQ PRO G500 01/02/2007
10. Lamp Menu
Image 10-4
When switching from the dual mode to the single mode the lamp with the longest runtime is switched off.
If the runtimes are equal (if the projector has always been operated in dual mode) then lamp1 is switched out.
When switching to single mode, returning to the dual mode will not be possible in the first 60 seconds, Dual
in the menu is greyed out and LED1 is flickering, thereby preventing hot restrike which may damage the lamp.
10.3 Power mode (only active in the iQG/R 500)
What can be done ?
The lamp power mode can be chosen to be in :
•
Full power mode : the total available power is used for the lamps (maximal brightness). This corresponds with the shortest
lamp lifetime (1500 hours)
•
Economy mode : the lamps are dimmed, the lifetime is extended to 3000 hours
The choice of the Power mode must be done during the installation of the projector. The switching between the 2 modes can only be
done 6 times and this only during the first 100 hours of the lamp lifetime (considering a dual lamp mode i.e. both lamps are used).
Lamps
replacement
Power Mode Switching
possible (max 6 times ! )
0
Power Mode Switching
possible (max 6 times ! )
100
1500
Runtime (hours)
(Full power mode)
or
3000
(econmy mode)
Image 10-5
Lamp power mode (projector considered to be running in dual lamp mode i.e. with both lamps on)
Above considerations and numbers (lifetimes) are only valid when functioning in dual lamp mode (both lamps
on)
How to select a Power mode ?
1. Press MENU to activate the Tool bar
2. Press → to select the Lamp item
3. Press ↓ to Pull down the Lamp menu
4. Use ↑ or ↓ to select Power Mode
5. Press → to pull down the menu
6. Use ↑ or ↓ to select the desired mode (image 10-6)
7. Press ENTER
R5976491 IQ PRO G500 01/02/2007
89
10. Lamp Menu
A dialog box is displayed. Confirm or cancel with Accept or Cancel (image 10-7)
Image 10-6
Image 10-7
10.4 History
How to view the history ?
1. Press MENU to activate the Tool bar
2. Press → to select the Lamp item
3. Press ↓ to Pull down the Lamp menu
4. Use ↑ or ↓ to select History (image 10-8)
5. Press ENTER
A textbox is displayed (image 10-9)
Image 10-8
90
R5976491 IQ PRO G500 01/02/2007
10. Lamp Menu
Image 10-9
10.5 Reset runtime
When to reset the lamp runtime ?
The lamp runtime should only be reset when placing a new lamp.
WARNING: Lamp runtime reset as well as the lamp replacement can only be done by a Barco authorized
technician.
How to reset the lamp runtime in the iQ/iD ?
1. Press MENU to activate the Tool bar
2. Press → to select the Lamp item
3. Press ↓ to Pull down the Lamp menu
4. Use ↑ or ↓ to select Reset runtime
5. Press → to pull down the menu
6. Use ↑ or ↓ to select the lamp to be reset (image 10-10)
7. Press ENTER
A dialog box is displayed (image 10-11)
8. Use ←or →, the numeric keys on the remote, or the keypad to change the serial number of the lamp (serial number 0000000 will
not be accepted).
Image 10-10
R5976491 IQ PRO G500 01/02/2007
91
10. Lamp Menu
Image 10-11
WARNING: Lamp runtime reset as well as the lamp replacement can only be done by a Barco authorized
technician.
How to reset the lamp runtime in the SIM5Plus?
1. Press MENU to activate the Tool bar
2. Press → to select the Lamp item
3. Press ↓ to Pull down the Lamp menu
4. Use ↑ or ↓ to select Reset runtime
5. Press → to pull down the menu
6. Use ↑ or ↓ to select the lamp to be reset
7. Press ENTER
A dialog box is displayed (image 10-12)
8. Use ←or →, the numeric keys on the remote, or the keypad to change the serial number of the lamp (serial number 0000000 will
not be accepted).
Image 10-12
WARNING: Lamp runtime reset as well as the lamp replacement can only be done by a Barco authorized
technician.
10.6 Runtime warning
What can be done ?
When the lamp has reached a certain predetermined runtime , a warning message will be displayed on the screen. The lamp runtime
warning can be set in a range from 30 to 200 hours. The runtime warning is displayed by default at 30 hours before end of lamp
lifetime.
92
R5976491 IQ PRO G500 01/02/2007
10. Lamp Menu
How to set the lamp runtime warning?
1. Press MENU to activate the Toolbar
2. Press → to select the Lamp item
3. Press ↓ to Pull down the Lamp menu
4. Use ↑ or ↓ to select Runtime warning (image 10-13)
5. Press ENTER
A dialogbox is displayed (image 10-14)
6. Use ←or →, the numeric keys on the remote, or the keypad to change the runtime warning setting.
Image 10-13
Image 10-14
WARNING: Lamp runtime reset as well as the lamp replacement can only be done by a Barco authorized
technician.
R5976491 IQ PRO G500 01/02/2007
93
10. Lamp Menu
94
R5976491 IQ PRO G500 01/02/2007
11. Image files menu
11. IMAGE FILES MENU
Overview
•
Load file
•
Auto Image
•
Edit file
•
Rename file
•
Copy
•
Delete
•
Forced file load
11.1 Load file
How to load a file ?
1. Press MENU to activate the Tool bar
2. Press → to select the Image files item
3. Press ↓ to Pull down the Image files menu
4. Use ↑ or ↓ to select Load (image 11-1)
5. Press ENTER
A dialog box is displayed (image 11-2)
6. Use ↑ or ↓ to select the desired file
Tip:
For more info about the available image files and the specifications, see "Standard Image Files", page 177
7. Press ENTER
The file is loaded and the image is adapted.
Image 11-1
R5976491 IQ PRO G500 01/02/2007
95
11. Image files menu
Image 11-2
In PiP mode, the files which may be loaded will be of the data type if the active window is a data window, or
they will be of the video type if the active window is a video window.
What to do if the image is not perfect ?
If the displayed image is not correct after AutoImage or after selecting the best fitting file, go to the Edit menu, select the active file
and change the settings.
11.2 Auto Image
What can be done ?
Auto Image creates the best suited image file for the connected source.
It calculates/measures several source parameters :
•
Total pixels per line
•
Start pixel
•
Phase
•
Contrast/Brightness levels
Auto Image works only for data images.
The measure of the total number of pixels per line can be done through 2 methods
•
Limited scan: a windowing is used to allow fast tracking.
The operation takes about 20 seconds (depending on file)
•
Full scan: tracking is done over the full range.
The operation takes about 1.5 minutes (depending on file)
How to launch Auto Image?
1. Press MENU to activate the Tool bar
2. Press → to select the Image files item
3. Press ↓ to Pull down the Image files menu
4. Use ↑ or ↓ to select Auto Image
5. Press → to open the menu
6. Use ↑ or ↓ to select the desired file scan method (image 11-3)
7. Press ENTER
96
R5976491 IQ PRO G500 01/02/2007
11. Image files menu
A text box showing a progress bar is displayed. (image 11-4)
Tip:
Press the Cancel button to cancel the operation.
Image 11-3
Image 11-4
The Auto Image setup in the Display setup menu affect only Auto Image if it is launched via the RCU key or at
automatic file creation.
Launching AutoImage via the menu involves complete checking of all parameters.
Auto Image can also be launched via the RCU with the dedicated AutoImage key.
11.3 Edit file
What can be done with the Edit file menu ?
The Edit file menu makes it possible to change the settings of the file according to the real settings of the connected source. Consult
the source specifications before entering the data.
How to edit a file ?
1. Press MENU to activate the Tool bar
2. Press → to select the Image files item
3. Press ↓ to Pull down the Image files menu
4. Use ↑ or ↓ to select Edit (image 11-5)
5. Press ENTER
A dialog box is displayed
6. Use ↑ or ↓ to select the desired file
Note: If in PiP mode the cursor is placed by default on the active file which has the focus.
7. Press ENTER
A dialog box is displayed (image 11-6)
8. Press ENTER
R5976491 IQ PRO G500 01/02/2007
97
11. Image files menu
A dialog box is displayed (image 11-7)
9. Use ←or →, the numeric keys on the remote, or the keypad to edit and change the values, confirm with ENTER
Note: greyed out fields can not be updated (total pixels)
Image 11-5
Image 11-6
Image 11-7
Which items can be adjusted ?
The following items can be adjusted :
98
•
Active horizontal pixels
•
Horizontal start in pixels
•
Horizontal period in ns
•
Active vertical lines
•
Vertical start in lines
R5976491 IQ PRO G500 01/02/2007
11. Image files menu
Advanced video settings
Image 11-8
The advanced button enables the advanced settings for a video source.
video signal
frame blanking
video signal
egalisation
HI
Image 11-9
HI AGC Hold interval
The Comb filter is by default enabled.
The AGC hold interval is the time interval in which the AGC is inhibited (AGC hold = no update in video amplitude measurement),
the advanced parameter allows to choose a short or long hold interval.
A long AGC hold interval eliminates Macrovision ® disturbances since the AGC is hold during a long interval, thus reducing the
probability to encounter a Macrovision ® pulse.
The sync locking setting is recommended for poor video signals (ex: poor TV signals).
Sharpness adjustment can be chosen to be coarse or fine.
It is recommended to use the default values.
Advanced Data settings
The advanced button enables the advanced settings for a data source.
R5976491 IQ PRO G500 01/02/2007
99
11. Image files menu
video info
a
b
Hs
Hs
Image 11-11
Hs horizontal sync pulse
a active low
b active high
Image 11-10
The VCO range setting determines the frequency range of the VCO (Voltage Controlled Oscillator).
The Cpmp (Charge pump current) sets the low pass filter current.
Both VCO range & Cpmp are set by the image file, changing these settings is only indicated in for special purposes.
The horizontal sync polarity setting can be useful in case of a bad shaped edge, one can choose between the leading (active low)
or trailing (active high) edge.
The input format settings are used to "tell more" about the signals connected on the BNC’s, it completes the information in the source
selection menu.
- RGB is selected by default and means that an RGB signal is connected to the BNC’s
- PR/Y/PB must be selected whenever:
•
a progressive signal (32 kHz frequency video signal ) is connected to the BNC’s (select the source with Data on BNC’s in the
Source selection menu).
•
one wants (in PiP mode) to visualize the component video signal in a Data window hereby adding a video image in the PiP
layout.
-HDTV-PR/Y/PB for high definition component video signals.
It is recommended to use the default values.
11.4 Rename file
How to rename a file ?
1. Press MENU to activate the Tool bar
2. Press → to select the Image files item
3. Press ↓ to Pull down the Image files menu
4. Use ↑ or ↓ to select Rename (image 11-12)
5. Press ENTER
A dialog box is displayed (image 11-13)
6. Use ↑ or ↓ to select the desired file
7. Press ENTER
A text box is displayed (image 11-14)
Use ←or →, ↓ or ↑ the numeric keys on the remote, or the keypad to edit and change the values, confirm with ENTER.
100
R5976491 IQ PRO G500 01/02/2007
11. Image files menu
Image 11-12
Image 11-14
Image 11-13
11.5 Copy
How to copy a file ?
1. Press MENU to activate the Tool bar
2. Press → to select the Image files item
3. Press ↓ to Pull down the Image files menu
4. Use ↑ or ↓ to select copy (image 11-15)
5. Press ENTER
A dialogbox is displayed (image 11-16)
6. Use ↑ or ↓ to select the desired file
7. Press ENTER
A text box is displayed (image 11-17)
Use ←or →, ↓ or ↑ on the remote, or the keypad to enter the new name, confirm with ENTER.
R5976491 IQ PRO G500 01/02/2007
101
11. Image files menu
Image 11-15
Image 11-17
Image 11-16
If the AutoImage function does not succeed in finding a file and no file is loaded (load list is empty), which
means that the source is not displayed, then use the copy function: Copy a standard file (.std) which is not
too different of the source to display, then edit this file to get the best image.
11.6 Delete
How to delete a file ?
1. Press MENU to activate the Tool bar
2. Press → to select the Image files item
3. Press ↓ to Pull down the Image files menu
4. Use ↑ or ↓ to select delete (image 11-18)
5. Press ENTER
A dialog box is displayed (image 11-19)
6. Use ↑ or ↓ to select the desired file
7. Press ENTER
The selected file is deleted and is removed from the list
102
R5976491 IQ PRO G500 01/02/2007
11. Image files menu
Image 11-18
Image 11-19
11.7 Forced file load
What can be done ?
Forced file load allows to force or lock one particular custom file to be loaded for one particular input. This way one can guarantee
that the same desired file is always used for a particular source.
For each layer (layer 1, layer 2, layer 3) we can enable or disable the forced file load. The specification for the file to be selected for
each input on that layer is done via RS232.
see the RS232 User Guide for more information on the Forced file load command to be sent.
How to set a file to be loaded ?
1. Press MENU to activate the Tool bar
2. Press → to select the Image files item
3. Press ↓ to Pull down the Image files menu
4. Use ↑ or ↓ to select Forced file load
5. Press → to open the menu (image 11-20)
6. Use ↑ or ↓ to select the desired layer
7. Press ENTER
Forced file load is activated for this layer (this is shown with a bullet)
R5976491 IQ PRO G500 01/02/2007
103
11. Image files menu
Image 11-20
104
R5976491 IQ PRO G500 01/02/2007
12. Display setup
12. DISPLAY SETUP
Overview
•
Full screen representation
•
Startup screen
•
Textbox
•
Take screenshot
•
Menu bar position
•
Status bar position
•
Sliderbox position
•
AutoImage Setup
•
Blanking
12.1 Full screen representation
Purpose of the Full screen representation
The Full screen representation function forces to use the complete native resolution of the LCD panels independently of the native
resolution of the source.
Note that the full screen representation does not preserve the aspect ratio of the source, i.e. when the aspect ratio of the active
image is not the same as the projector (in this case 1920/1080 or 1.77:1), the image will end to be distorted (stretched or shrinked).
How to enable/disable the full screen representation ?
1. Press MENU to activate the Tool bar
2. Press → to select the Display setup item
3. Press ↓ to Pull down the Display setup menu
4. Use ↑ or ↓ to select Full screen representation
5. Press → to pull down the menu
6. Use ↓ or ↑ to select ON or OFF
7. Press ENTER
The full screen representation will not guarantee the best image quality, therefore the Show native resolution
has to be selected.
The show native resolution function on the other hand forces to use the native resolution of the source.
The Full screen representation function overrules the show native resolution function.
The aspect ratio setting is greyed out when enabling the full screen representation.
12.2 Startup screen
What can be done ?
When the startup screen is enabled, the identification screen is displayed for a few seconds at startup. This startup screen can also
be disabled.
R5976491 IQ PRO G500 01/02/2007
105
12. Display setup
Image 12-1
How to enable/disable the Startup screen?
1. Press MENU to activate the Tool bar
2. Press → to select the Display setup item
3. Press ↓ to Pull down the Display setup menu
4. Use ↑ or ↓ to select Startup screen
5. Press → to pull down the menu
6. Use ↓ or ↑ to select the ON or OFF
7. Press ENTER
12.3 Textbox
What can be done ?
The textbox function allows to display or not the different sliderboxes used for instance for picture settings (contrast,...), it also affects
the source information windows (displayed in the right lower corner of the screen).
How to enable/disable the Textbox ?
1. Press MENU to activate the Toolbar
2. Press → to select the Display setup item
3. Press ↓ to Pull down the Display setup menu
4. Use ↑ or ↓ to select Textbox
5. Press → to pull down the menu
6. Use ↓ or ↑ to enable/disable the textbox
7. Press ENTER
12.4 Take screenshot
What can be done ?
A screenshot can be taken from an active projected image. This screenshot is then saved in a 4 MB RAM and can be used as
background.
Each new screenshot erases the previous logo therefore a warning message is displayed asking the user to confirm.
106
R5976491 IQ PRO G500 01/02/2007
12. Display setup
Image 12-2
Default (factory stored) Logo
How to take a screenshot ?
1. Press MENU to activate the Tool bar
2. Press → to select the Display setup item
3. Press ↓ to Pull down the Display setup menu
4. Use ↑ or ↓ to select Take screenshot (image 12-3)
5. Press ENTER
A dialog box is displayed. Press yes to confirm. (image 12-4)
A text box shows the evolution of the operation. (image 12-5, image 12-6)
Image 12-3
Image 12-4
Image 12-5
Image 12-6
R5976491 IQ PRO G500 01/02/2007
107
12. Display setup
12.5 Menu bar position
What can be done ?
The menu toolbar can be centered vertically , the range being from top of the screen to the middle of the screen. This can be useful
in applications where the top image content is not displayed.
How to center the menu ?
1. Press MENU to activate the Toolbar
2. Press → to select the Display setup item
3. Press ↓ to Pull down the Display setup menu
4. Use ↑ or ↓ to select Menu bar position menu (image 12-7)
5. Press ENTER
6. Use ↑ or ↓ to position the menu toolbar
Image 12-7
12.6 Status bar position
What can be done ?
The status bar (wizard menu) can be centered vertically , the range being from bottom of the screen to the middle of the screen.
This can be useful in applications where the bottom image content is not displayed.
How to center the menu ?
1. Press MENU to activate the Toolbar
2. Press → to select the Display setup item
3. Press ↓ to Pull down the Display setup menu
4. Use ↑ or ↓ to select Status bar position (image 12-8)
5. Press ENTER
6. Use ↑ or ↓ to position the status bar
108
R5976491 IQ PRO G500 01/02/2007
12. Display setup
Image 12-8
12.7 Sliderbox position
What can be done ?
The sliderbox can be displayed anywhere on the screen, the position can be set in this menu.
How to reposition the sliderbox?
1. Press MENU to activate the Tool bar
2. Press → to select the Display setup item
3. Press ↓ to Pull down the Display setup menu
4. Use ↑ or ↓ to select Sliderbox position (image 12-9)
5. Press ENTER
A sliderbox is displayed. Use the 4 arrow keys to drag the box to the desired position. (image 12-10)
Image 12-9
Image 12-10
There is a coarse and a fine adjustment of the position, use ENTER (when sliderbox is displayed) to switch
between the two.
R5976491 IQ PRO G500 01/02/2007
109
12. Display setup
12.8 AutoImage Setup
What can be done ?
Autoimage allows to detect automatically the characteristics of the source (total pixels per line,...) and uses this information to adapt
the image to the LCD panels.
Autoimage can adapt the image based on following data :
•
Total pixels per line
•
Start pixel
•
Phase
•
Contrast/brightness levels
Autoimage works only for data signals.
How to set up AutoImage?
1. Press MENU to activate the Tool bar
2. Press → to select the Display setup item
3. Press ↓ to Pull down the Display setup menu
4. Use ↑ or ↓ to select AutoImage setup (image 12-11)
5. Press ENTER
A dialog box is displayed.
(image 12-12)
6. Use the arrow keys to select the desired item and press ENTER to activate or disactivate the item.
Image 12-11
Image 12-12
How to perform AutoImage ?
1. Press AutoImage on the RCU
A textbox showing a progress bar is displayed.
110
R5976491 IQ PRO G500 01/02/2007
12. Display setup
During the AUTOIMAGE measuring process the data source disappears temporarily (logo is displayed if background is set to logo )
12.9 Blanking
What can be done ?
The image can be blanked in several ways :
•
Top blanking
•
Bottom blanking
•
Left blanking
•
Right blanking
Image 12-13
Note that here the blanking is only done on the display i.e. the setting is not saved in the image file. in other
words only one type of blanking (setting) can be done independently of the source.
How to blank the image ?
1. Press MENU to activate the Toolbar
2. Press → to select the Display setup item
3. Press ↓ to Pull down the menu
4. Use ↑ or ↓ to select Blanking (image 12-14)
5. Press ENTER
A slider box is displayed (image 12-15)
6. Use ←or →, the numeric keys on the remote, or the keypad to change the blanking.
R5976491 IQ PRO G500 01/02/2007
111
12. Display setup
Image 12-14
Image 12-15
Use the checkboxes to enable/disable the blanking
Use the Reset key to reset the blanking values.
The logo is also affected by the blanking
112
R5976491 IQ PRO G500 01/02/2007
13. Installation menu
13. INSTALLATION MENU
Overview
•
Lens adjustments
•
Projector address
•
Orientation
•
Language
•
Quick access keys
•
RS232 baudrate
•
Automatic startup
•
Security
•
Change password
•
Gemini installed (only for GEMINI CADWALL systems ! )
13.1 Lens adjustments
What can be done ?
Motorized lenses can be adjusted in the installation menu or via the dedicated keys on the remote.
The following parameters can be adjusted:
•
Zoom
•
Focus
•
Shift (also for non motorized lenses)
How to Zoom/focus or shift ?
1. Press MENU to activate the Toolbar
2. Press → to select the Installation
3. Press ↓ to Pull down the Installation menu
4. Use ↑ or ↓ to select Lens adjustment (image 13-1)
5. Press ENTER
A textbox appears on the screen, follow the instructions. (image 13-2, image 13-3)
Image 13-1
R5976491 IQ PRO G500 01/02/2007
113
13. Installation menu
Image 13-2
Image 13-3
13.2 Projector address
What can be done ?
The projector is shipped with projector address set to ”0”
In some cases the projector address must be changed, for example if an unique RCU is used to control 2 or more projectors (independently).
In the OSD menu Projector Address, the following addresses can be programmed :
•
Projector address: address defined by the user, may be from 0 to 255
0-9 is used for RCU communication, 0–255 being used for RS232 serial communication.
•
Common address : address may be 0 or 1
How to change the projector’s RC5 address ?
1. Press MENU to activate the Tool bar
2. Press → to select the Installation
3. Press ↓ to Pull down the Installation menu
4. Use ↑ or ↓ to select Projector address (image 13-4)
5. Press ENTER
A dialog box appears on the screen. (image 13-5, image 13-6)
Image 13-4
114
R5976491 IQ PRO G500 01/02/2007
13. Installation menu
Image 13-5
Image 13-6
Entering the new projector address ?
1. Enter the new projector address with the digit keys on the RCU, the local keypad or the cursor keys.
This address must be between 0 and 255.
How to change the common RC5 address ?
1. Press MENU to activate the Tool bar
2. Press → to select the Installation
3. Press ↓ to Pull down the Installation menu
4. Use ↑ or ↓ to select Projector address
5. Press ENTER
A dialog box appears on the screen.
Entering the new common address ?
1. Enter the new projector address with the digit keys on the RCU, the local keypad or the cursor keys.
This address must be between 0 or 1.
13.3 Orientation
Projector orientations
Depending on how the projector is oriented, the projector’s internal settings have to be adapted.
How to change the orientation ?
1. Press MENU to activate the Toolbar
2. Press → to select the Installation item
3. Press ↓ to Pull down the Installation menu
4. Use ↑ or ↓ to select Orientation
5. Press → to pull down the menu
6. Use ↓ or ↑ to select the desired orientation (image 13-7)
7. Press ENTER
The projection is adapted and a black bullet shows the active configuration.
R5976491 IQ PRO G500 01/02/2007
115
13. Installation menu
Image 13-7
13.4 Language
List of languages
The list of selectable languages is depending on the software of the projector.
How to change the Language ?
1. Press MENU to activate the Tool bar
2. Press → to select the Installation item
3. Press ↓ to Pull down the Installation menu
4. Use ↑ or ↓ to select Language
5. Press → to pull down the menu
6. Use ↓ or ↑ to select the desired language (image 13-8)
7. Press ENTER
The language is adapted and a black bullet shows the active configuration.
Image 13-8
116
R5976491 IQ PRO G500 01/02/2007
13. Installation menu
13.5 Quick access keys
What can be done ?
The 3 function keys on top of the RCU can be associated with a particular item in one of the menus.
Each function which is not password protected or does not have a key on the RCU can be associated to a function key.
How to get an overview of the quick access keys ?
1. Press MENU to activate the Tool bar
2. Press → to select the Installation
3. Press ↓ to Pull down the Installation menu
4. Use ↑ or ↓ to select Quick access keys (image 13-9)
5. Press ENTER
A text box appears on the screen.
Image 13-9
How to program the quick access keys ?
1. Scroll through the menus to the desired menu item
2. Push the desired function key for 3 seconds (image 13-10)
The menu item is stored in the quick access key
F1
M EN U
F2
F3
B AC K
Image 13-10
Factory pre-programmed functions
-F1 : color depth
-F2 : noise reduction
-F3 : orientation
R5976491 IQ PRO G500 01/02/2007
117
13. Installation menu
13.6 RS232 baudrate
How to change the baudrate?
1. Press MENU to activate the Tool bar
2. Press → to select the Installation item
3. Press ↓ to Pull down the Installation menu
4. Use ↑ or ↓ to select RS232 baudrate (image 13-11)
5. Press → to pull down the menu
6. Use ↓ or ↑ to select the desired baudrate
7. Press ENTER
Image 13-11
13.7 Automatic startup
What can be done ?
The automatic startup allows immediate restart of the projector after a power failure (breakdown), i.e. without passing through the
standby state.
The projector restarts at power resume and recovers the previous settings (previous source,...).
This function can be disabled if undesired or inadequate for safety reasons, etc.
CAUTION: If the Automatic startup function is enabled one must be aware of the fact that it involves safety
precautions
Make sure that the projector (or the operators!) will not be affected by altered environmental conditions when
restarting at power resume.
How to enable/disable the Automatic startup?
1. Press MENU to activate the Tool bar
2. Press → to select the Installation item
3. Press ↓ to Pull down the Installation menu
4. Use ↑ or ↓ to select Automatic startup
5. Press → to pull down the menu
6. Use ↓ or ↑ to enable/disable the automatic startup
7. Press ENTER
118
R5976491 IQ PRO G500 01/02/2007
13. Installation menu
13.8 Security
What can be done ?
A security function is implemented in the projector and allows a protection against theft.
A PIN code allows the user to lock the projector in case of wrong code entry.
The PIN code must be entered at each start up (Power ON), entering three times a wrong number triggers a wait cycle of 15 minutes,
the second 3 wrong codes a wait cycle of 30 minutes, 1 hour, ...
The security mode can be enabled or disabled.
How to activate the security mode ?
1. Press MENU to activate the Tool bar
2. Press → to select the installation item
3. Press ↓ to Pull down the menu
4. Use ↑ or ↓ to select Security (image 13-12)
5. Press → to open the menu
6. Use ↑ or ↓ to select ON
7. Press ENTER
A dialog box is displayed (image 13-13)
8. Use the arrow keys to select YES and press ENTER to confirm
A dialog box is displayed
Enter your name, company name,... (this information is displayed in the identification menu) (image 13-14)
9. Press ACCEPT
A dialog box is displayed.
Enter the PIN code, and confirm it. (image 13-15)
An informative text box is then displayed. Press ENTER or BACK to escape. (image 13-16)
Image 13-12
R5976491 IQ PRO G500 01/02/2007
119
13. Installation menu
Image 13-13
Image 13-15
Image 13-14
Image 13-16
How to disable the security mode ?
1. Press MENU to activate the Tool bar
2. Press → to select the installation item
3. Press ↓ to Pull down the menu
4. Use ↑ or ↓ to select Security
5. Press → to open the menu
6. Use ↑ or ↓ to select OFF
7. Press ENTER
120
R5976491 IQ PRO G500 01/02/2007
13. Installation menu
A dialog box is displayed
8. Enter your PIN code
The security mode is now disabled
13.9 Change password
How to change the password ?
1. Press MENU to activate the Tool bar
2. Press → to select the Installation item
3. Press ↓ to Pull down the Installation menu
4. Use ↑ or ↓ to select Change password (image 13-17)
5. Press ENTER
A dialog box is displayed.
(image 13-18)
6. Use ← or → , the numeric keys on the remote , or the keypad to enter and confirm the new password.
Each character is displayed as an asterisk.
Image 13-17
Image 13-18
The new password is accepted if the new password and the confirmed password coincide.
If the password is forgotten contact a Barco authorized technician.
R5976491 IQ PRO G500 01/02/2007
121
13. Installation menu
13.10 Gemini installed (only for GEMINI CADWALL systems ! )
When to enable ?
Gemini is option is necessary when the iQ is used in a Gemini 2 channel CADWALL system. By enabling Gemini the restrictions
relative to the allowed difference in the number of total lines are changed :
•
1 line for non interlaced sources (instead of 0)
•
2 lines for interlaced sources (instead of 1)
The default setting is NO. Never activate this option if not in presence of a Gemini CADWALL system.
How to enable Gemini ?
1. Press MENU to activate the Toolbar
2. Press → to select the Installation item
3. Press ↓ to Pull down the Installation menu
4. Use ↑ or ↓ to select Gemini installed (image 13-19)
5. Use ↑ or ↓ to select ON
6. Press ENTER
The Gemini option is enabled
Image 13-19
122
R5976491 IQ PRO G500 01/02/2007
14. IQ Network
14. IQ NETWORK
LAN
Local Area Network
WAN
Wide Area Network
Overview
•
Network architecture
•
Network functionality
•
iQ Pro Server specifications
•
Getting started
•
Control
•
Management & diagnostics
•
Configuration
•
DropZone
•
The Web client
14.1 Network architecture
SBC
Single Board Computer,
GUI
Graphic User Interface
Topology
The network centric projector (iCon and iQPro) uses an integrated PC (SBC) and can be connected to a LAN.
The projector performs the role of Server while each PC is declared as a Client within the system.
Each client PC has to be configured (projector IP address, ...), see “Configuring the client software”
R5976491 IQ PRO G500 01/02/2007
123
14. IQ Network
RM : Remote control &
Management
A : SERVER
M2 : Meeting room
P : projection area
V : streaming video data
LAN
WAN
M3 : Large conference room
M1 : Meeting room 1
R : remote meeting attendee
Image 14-1
Typical iQ Pro network architecture
A server
RM Remote Control and Management
M1 Meeting room 1
M2 Meeting room 2
M3 Large screen conference room
P Projection area
R Remote meeting attendee
V Streaming Video data
Wireless LAN (point-to-point) is also possible (using the PCMCIA connection on the projector ) and complements the functionality of direct cabling.
14.2 Network functionality
What can be done ?
The network functionality allows the projector to perform several network functions thanks to network features which are required in
most corporate environments:
•
124
Control & Management : wireless/wired (remote) control and monitoring of the projector(s) thanks to a user-friendly GUI (the
Client software).
•
Diagnostics : diagnostics through a user-friendly GUI and automatic E-mail sending.
•
Easy file (MS PowerPoint,...) manipulation and projection using the DropZone interface.
•
Remote control of the projector by allowing the desktop to be shared over the network (the DropZone interface).
•
Streaming media : The projector’s onboard computer is streaming video data ready, i.e. allowing the decoding of video streaming data coming from a server via the LAN.
R5976491 IQ PRO G500 01/02/2007
14. IQ Network
The network centric projector may be configured in the same way as a standard PC to support :
- SNMP service : provides diagnostics, basic control via SNMP messaging
- Microsoft Exchange services: for scheduling of projector tasks.
- Web client : offers an alternative to the Client software through a user-friendly internet based
interface (includes almost the same features as the Client software)
See the Appendix “General guidelines on Network configuration” for general guidelines on how to enable
these services.
14.3 iQ Pro Server specifications
Specifications of the iQ Pro Server platform
•
1.2 GHz Pentium III processor
•
256 MB RAM
4
•
40 GB Hard Disk storage
•
Microsoft XP Operating System
•
Barco Server Software for network communication between iQ Pro Server and clients
14.4 Getting started
Overview
•
Connections
•
Installing the software
•
Start up of the iQ Pro Server
•
Configuring the client software
•
Configuring the Server software
The installation of the iQ Pro in a Local Area Network must be done in the same way as the installation of
a standard PC in that particular network meaning that the same rules and accepted practice should be respected.
The assistance of qualified IT personnel is advised.
CAUTION:
Important !
A Virus protection program should be installed and kept up to date to prevent virus infections.
CAUTION: The maintenance of the Server must be done in the same way as a PC meaning that the same rules
and accepted practice should be respected.
Backups should be taken on a regular basis.
In the same way virus updates should be done regularly.
Barco will not be held responsible for destroyed information in case of a hard disk breakdown or virus infection and has no obligation to pay for or reimburse for the cost of recovering data.
4. the pentium III socket is upgradeable
R5976491 IQ PRO G500 01/02/2007
125
14. IQ Network
14.4.1 Connections
Front plate (Layer 3) layout
PC CARD
D
10/100 Base-T
MIC IN LINE IN OUT
A
USB
B
C
Image 14-2
iQ Pro front plate (network layer)
A
B
C
D
audio connections : mic input, line input, output
4 x USB connection
RJ45 connector for network connection
PCMCIA slot
How to connect the Single Board Computer ?
1. Use the RJ45 connector to connect the SBC to the installed network
2. Use the USB ports to connect peripherals such as mouse, keyboard,... (image 14-3)
Note: Keyboard access during pre-operating system boot (to access BIOS or F8 key to get operating system select menu) is
only supported on the bottom USB input connector next to the Ethernet connector
3. Use the PCMCIA slot to connect a Wireless LAN card or other optional inputs like Bluetooth, Modem cards,...
The slot is protected from dust by a slot door, open the slot door to insert a card.
Note: recommended card type:
-The card should be a type II card.
-The card should be Windows TM XP compatible
4. Use the Audio connectors to connect an audio source or microphone, the output allows to use an external audio peripheral such
as an amplifier etc.
Image 14-3
126
R5976491 IQ PRO G500 01/02/2007
14. IQ Network
Point to point configuration
B
A
Image 14-4
In case of a temporary configuration (demo purposes) one can use the point to point configuration, the connection being done via RJ45 connections using a crossed UTP cable.
14.4.2 Installing the software
An Administrator password has been installed for security reasons (worm and virus protection):
Password : Barco (case sensitive !)
Necessary parts
•
installation CD (delivered)
•
PC
How to install the client software ?
1. Install the client software from the CD ( Setup file )
How to install the server software ?
1. The server software is by default installed on the projector.
if necessary, reinstall it from the CD.
The CD containing the server software and the client tools are delivered with the projector. They can always
be downloaded from the secured PartnerZone Web site : https://secure.barco.com/presentation/
14.4.3 Start up of the iQ Pro Server
Starting up
There are 2 methods to start up the iQ Pro Server
•
Manual start up (via the General menu)
•
Automatic startup at projector startup: this is done by defining the state of the iQ Pro Server during a “Projector ON state” and
a “Projector standby state” .
Manual start up: How to start up/shut down/reset the iQ Pro Server ?
1. Press MENU to activate the Toolbar
2. Press → to select General
3. Press ↓ to Pull down the General menu
4. Use ↑ or ↓ to select iQ Pro Server
5. Press → to open the menu
6. Use ↑ or ↓ to select ON/OFF/Reset (image 14-5)
7. Press ENTER
R5976491 IQ PRO G500 01/02/2007
127
14. IQ Network
Image 14-5
When resetting the PC the menuitems in the iQ Pro Server menu are greyed out during a short period.
Projector Standby state setting
This setting defines what should happen with the iQ Pro Server when the projector is switched to standby.
The iQ Pro Server can stay in the ON state or it can be switched OFF
Projector On state setting
This setting defines what should happen with the iQ Pro Server when the projector is switched on.
The iQ Pro Server can stay OFF (switching on can then happen manually in the general menu) or it can be switched on (at the same
time as the projector)
Automatic start up: How to set the automatic startup ?
1. Press MENU to activate the Toolbar
2. Press → to select Installation
3. Press ↓ to Pull down the menu
4. Use ↑ or ↓ to select iQ Pro Server settings
5. Press ENTER
6. A dialogbox is displayed (image 14-6)
7. Select ON for the “Projector On state” setting
The iQ Pro Server will now be automatically switched on at the next startup of the projector
Image 14-6
The iQ Pro Server will be switched on but not necessarily selected by default, go to Source selection in the
menu to select the iQ PC.
128
R5976491 IQ PRO G500 01/02/2007
14. IQ Network
14.4.4 Configuring the client software
The same universal client interface is used for different network centric projectors (iQ, iD, iCon). The layout of
the interface (position of the controls,...) is adapted after detection of the projector type. Some screenshots
may not fully coincide with the reality.
How to start up the client software ?
1. Start up the previously installed client program
The interface shows 3 tabs (upper tab control ): Control, Diagnosis and Configuration
The active sub interface is the control sub screen (image 14-7)
2. Click on the upper menubar to select the desired sub interface
Image 14-7
Control interface
IP
Internet Protocol. The network layer of TCP/IP. Required for communication with the internet.
How to add a projector to the projector list
1. Click on the white arrow (image 14-8)
A menu is dropped down (image 14-9)
2. click on the + sign of the projector list
A dialog box is displayed (image 14-10)
3. Fill in the Name, the IP address (optional) and the Port number of TCP/IP connection
Note: default port number = 9999
4. Fill in the alias
Tip:
“Alias” is a custom name whereas “Name” is the name by which the projector is identified on the (corporate) network
5. Click OK to confirm or Cancel
The projector is now added to the list of projectors
R5976491 IQ PRO G500 01/02/2007
129
14. IQ Network
Image 14-8
Image 14-10
Image 14-9
projector list: contains a
projector and a projector group
sub list
Depending on the installed network (use of DHCP server or not), the IP address may be needed to be entered
or not.
For a point to point installation the projector’s IP address must be entered manually.
Check the operating system on the for the IP address, or contact your IT administrator.
How to add a projector group to the projector group list ?
1. Click on the white arrow
A menu is displayed, image 14-9
2. Click on the + sign of the projector group list
A dialog box is displayed (image 14-11)
3. Fill in the group name
4. Click OK to confirm or Cancel
The group is now added to the list of groups
130
R5976491 IQ PRO G500 01/02/2007
14. IQ Network
Image 14-11
How to add projectors to a group ?
1. Click on the projector to be added in the projector list
2. Drag the projector down to the projector group.
The projector is added to the group.
Adding a projector to a group can also be done by using the “Copy + Paste” method on the right mouse button
menu.
How to connect to a projector or group of projectors ?
1. Double click on the projector or group of projectors
A green dot appears, indicating that the projector is present on the network and working properly (image 14-12)
The name of the projector or group is now displayed in the upper part of the screen and indicates that the communication has
been set (image 14-13)
Image 14-12
connected and active projector
A
connected and active projector
Image 14-13
A
connected and active projector
When connected to a group of projectors, some controls may be disabled.
In general, controls will only be selected if this is the status of all projectors in the group.
Sliders will be set to a particular value only if this is the same on all projectors in the group, otherwise they
will be positioned centrally with a dash in the value box. When the slider is moved the box will show the new
value and this value will be sent to all projectors in the group.
Labels such as Current Source in the general page will only be shown if the string value is the same on all
projectors, otherwise a dash will be shown
The Target information block
The target information block displays the main characteristics of the connected projector or group of projectors.
This gives also an indication whether the communication setting has been successful or not.
R5976491 IQ PRO G500 01/02/2007
131
14. IQ Network
Image 14-14
14.4.5 Configuring the Server software
Internal network connection
The internal connection ( firmware connection) between the projector controller and the single board computer uses fixed IP addresses.
The IP address of the SBC can be found in control panel
•
SBC: IP address = 192.168.42.51, subnet mask = 255.255.255.248
Projector Controller’s IP address = 192.168.42.50
Image 14-15
132
R5976491 IQ PRO G500 01/02/2007
14. IQ Network
Image 14-16
Image 14-17
CAUTION:
Leave these IP addresses unchanged !
The server menu
The server menu can be opened by right clicking from the server tray icon
R5976491 IQ PRO G500 01/02/2007
133
14. IQ Network
Image 14-18
Start Meetings control
The meeting control is started and positioned on the desktop, through out the meeting it will allow to :
•
Accept requests interactively : a request for a desktop sharing from a client PC must be accepted on the iCon server, a dialog
box is displayed on the iCon asking to accept or decline the desktop sharing request
•
Deny all requests : all request are denied
•
Accept all requests automatically : desktop sharing is always accepted at the iCon (server) without prompting for confirmation
•
Notify end of meeting at : allows to set a reminder at expected end time of the meeting
Image 14-19
How to configure the Server settings ?
1. Go to the server icon in the lower task bar of the desktop and click the right mouse button.
A menu is displayed
2. Select Settings
A dialog box is displayed allowing to select different tabs
134
-
Networking
-
Dropzone, see Dropzone chapter
-
Exchange
R5976491 IQ PRO G500 01/02/2007
14. IQ Network
Networking settings
Image 14-20
•
Port settings: it is advised to leave these settings in their default value.
•
Mail to field : see mail configuration in the client software
•
SNMP enable: allows to enable the SNMP control of the projector.
The Enable write option allows to enable the client to overwrite projector settings via
SNMP.
Unchecking this option means that projector settings will only be read.
Exchange settings
This tab allows to fill in the exchange parameters to allow scheduling of projector tasks.
These parameters should be configured by your local IT administrator
Image 14-21
Miscellaneous settings
This tab allows following settings :
R5976491 IQ PRO G500 01/02/2007
135
14. IQ Network
•
Enable password protection : when using a password, one must enter it when starting up the client interface
•
Automatically open sole document ... : when using a USB stick, the document is automatically opened (only when one document present).
When using a password, the control via the previous V1.1 client version will not be possible therefore disable
password protection. Note that using a previous client version in combination with V1.2 server is indicated
with following text box :
Image 14-22
client-server soft incompatibility
Image 14-23
To check the server version open the about menu from the tray
Image 14-24
136
R5976491 IQ PRO G500 01/02/2007
14. IQ Network
14.5 Control
Overview
•
Description
•
How to use the control manager?
•
General
•
The source selection screen
•
The PiP screen
•
Image settings
•
Advanced control
14.5.1 Description
What can be done ?
The projector allows a software client (client PC) to communicate locally with the server and hereby control the projector’s settings,
in this case one has a point to point communication, image 14-25. The client PC or laptop communicating with the projector may
be locally installed or may be remote, communication may then happen over a LAN, image 14-26
The projector performs the role of Server while the PC acts as a Client within the system.
The control and management client software incudes the possibility to create groups of projectors and that way control a whole fleet
of projectors.
B
A
Image 14-25
point to point iQ Pro network communication
A
B
facility manager’s desk
projector area
A : facility manager's desk
B : projection areas
...
LAN
Image 14-26
control & management of network centric projector(s)
A
B
facility manager’s desk
projector area
What can be controlled ?
Almost every menu item can be controlled through the control manager
R5976491 IQ PRO G500 01/02/2007
137
14. IQ Network
•
standby on/off
•
lamp mode
•
source selection
•
switching effects
•
background setting
•
all PiP settings (layout, window)
•
Image settings
•
lens adjustments
The control manager
The control interface in the client software is divided into 5 subscreens, image 14-27:
•
General
•
source selection
•
PiP
•
image settings
•
advanced
Image 14-27
The control interface: the general sub screen is active (see tool bar)
14.5.2 How to use the control manager?
How to use the control manager?
1. Choose the sub screen by clicking on the desired item on the tool bar in the upper part of the control interface
The active sub screen is indicated with a blue spot
14.5.3 General
What can be done ?
Basic controlling, monitoring and general parameter setting of the projector can be done in this screen, image 14-27.
•
3 buttons ON, STANDBY and PAUSE
•
The target information part gives the main characteristics of the projector
•
2 buttons allow to switch between dual and the single lamp mode
How to change the general settings?
1. Click on the lamp mode button to select the desired mode
A blue spot indicates the active mode
2. Click on one of the three buttons to start up, pause or put in standby the projector
A green led indicates the status of the projector.
138
R5976491 IQ PRO G500 01/02/2007
14. IQ Network
14.5.4 The source selection screen
What can be done ?
•
A source selection dialog box allows to visualize all the sources or only the detected sources.
•
3 buttons to activate, freeze, pause and logo
•
selection of 12 different switching effects
•
selection of 3 different backgrounds: logo, Blue, Black
Image 14-28
The source selection screen
How to select a source ?
1. Click on show all or show detected
Depending on the option (show all/detected) selected, a list is displayed.
In case show all is selected, a list of all possible sources is displayed, signal
presence is indicated with an orange dot.
When show detected is selected, all the detected sources are displayed with an orange dot.
2. Double click on the desired source
The selected source is now projected
In group mode there are only grey or green nodes, no orange (detected).
On start up, a green node will be shown when all projectors are playing the same source type.
Grey will be shown when some of the projectors are not showing the same source type.
If we double click on a grey node, it should go green as long as at least one of the projectors in the group can
show the source.
14.5.5 The PiP screen
Following screenshots are taken for an iQPro projector. The layouts may be slightly different for an iCon
(layout automatically adapted after projector type detection by the client).
What can be done ?
The PiP tool allows to manage the PiP of the projector in a more user friendly way:
•
a check box list allows to choose between 10 PiP layout (5 preset layouts and 5 personal layouts)
•
several buttons allow operations on windows (add, remove ) as well as on the PiP layouts (save, ...)
•
a graphical screen allows easy altering of the PiP layout : re sizing, positioning of the different windows.
R5976491 IQ PRO G500 01/02/2007
139
14. IQ Network
Image 14-29
PiP screen
How to perform operations on a PiP layout
As an example, let us choose a personal (non preset) layout, add a window, reposition the windows, and save the layout under a
different name.
1. Click on one of the check boxes to choose a layout
Choose a personal layout (image 14-30)
The PiP screen (as well as the projected layout) is updated (image 14-31)
This layout contains one window being an RGBHV Data source
2. Click on the Add window button
Note: if the layout already contains 4 window, it will be impossible to add a new one. In that case a window is displayed,
image 14-32
A dialog box is displayed showing the possible sources to be added. (image 14-33)
3. Select the source to be linked to the new window.
The window is added to the layout. (image 14-34)
4. When entering the PiP screen the cursor is replaced by a hand, Click on the window to be repositioned.
The window is surrounded by a white frame.
5. Drag the window to the desired position.
6. Place the cursor on one of the corners of the window to be re sized.
A double arrow is displayed.
7. Drag to re size.
Note: the window is re sized by keeping the same aspect ratio.
140
R5976491 IQ PRO G500 01/02/2007
14. IQ Network
Image 14-30
Image 14-31
Image 14-32
Image 14-33
Add window dialog box
Image 14-34
Importing/exporting a layout
Every PiP layout can be exported and saved as backup on the network or on the hard disk of the Client PC.
It can then be imported at any time.
R5976491 IQ PRO G500 01/02/2007
141
14. IQ Network
How to import/export a layout ?
1. Click on the Export button.
A dialog box is displayed. (image 14-35)
2. Browse to the desired location and fill in the filename.
Image 14-35
How to import a layout ?
1. Click on the import button.
A dialog box is displayed. (image 14-36)
2. Select the layout to be imported.
Image 14-36
For more information on Picture in Picture see the PiP chapter.
14.5.6 Image settings
What can be done ?
•
General settings
•
Color temperature
•
Geometry
General image settings
1. Click on Image settings menu in the tool bar to drop down the submenu (image 14-37)
2. Click on General
142
R5976491 IQ PRO G500 01/02/2007
14. IQ Network
3. Slide the cursors to set the corresponding value (image 14-38)
Image 14-37
Image 14-38
Use the checkbox to define a coarse or a fine setting.
Click on the Filmmode button to enable or disable the filmmode.
Color temperature preset settings
1. Click on Image settings menu in the tool bar to drop down the submenu.
2. Click on color temp, image 14-37
3. Click on the desired preset color temperature. (image 14-39)
Image 14-39
Custom color temperature setting
1. Click on the Custom button.
A dialog box is displayed. (image 14-40)
2. Use the sliders to set the red and the blue color temperature.
R5976491 IQ PRO G500 01/02/2007
143
14. IQ Network
Image 14-40
Geometry settings
1. Click on Image settings menu in the tool bar to drop down the submenu. (image 14-41)
2. Click on Geometry.
a dialog box is displayed. (image 14-42)
3. Use the buttons to zoom or pan.
Tip:
Use the buttons to choose small, medium or large adjustment steps.
Each click changes the setting.
4. Click on the desired aspect ratio and resolution handling mode.
Image 14-41
Image 14-42
14.5.7 Advanced control
Overview
144
•
Lens adjustments
•
Options
R5976491 IQ PRO G500 01/02/2007
14. IQ Network
14.5.7.1 Lens adjustments
How to adjust the lens ?
1. Click on the Advanced menu in the tool bar to drop down the submenu
2. Click on lens adjustments (image 14-43)
3. Use the buttons to shift/zoom/focus the lens (image 14-44)
Tip:
Use the buttons to choose small, medium or large adjustment steps.
Each click changes the setting.
Image 14-43
the Advanced control submenu
Image 14-44
14.5.7.2 Options
How to start up the options menu ?
1. Click on the Advanced menu in the tool bar to drop down the submenu.
2. Click on Options .
See image 14-45.
R5976491 IQ PRO G500 01/02/2007
145
14. IQ Network
Image 14-45
The advanced Options screen
How to set up and perform AutoImage ?
1. Check the boxes corresponding to the desired setting of AutoImage. (image 14-46)
2. Click on Apply to perform AutoImage.
Image 14-46
Lamp runtime warnings startup settings
1. Fill in the lamp runtime warning time. (image 14-47)
2. Click on startup screen to enable the startup screen.
3. Click on Auto Startup to enable automatic startup.
Image 14-47
A blue spot indicates that the function is enabled.
146
R5976491 IQ PRO G500 01/02/2007
14. IQ Network
14.6 Management & diagnostics
14.6.1 Description
What can be done ?
Diagnosis of a projector or a group of projectors is possible through on line monitoring. Mail services are also available and allow
the client to be periodically informed about status errors and warnings concerning the different components of the projector.
What can be diagnosed/checked ?
•
projector’s general parameters as type, serial number, embedded SW version,...
•
advanced diagnostics of the projector on board/component level: fpga, decoder,...
•
user defined critical components (by E-mail feedback, see E-mail configuration)
14.6.2 Diagnostics manager
How to start up ?
1. Click on diagnostics in the main tool bar
How to check the general diagnostics ?
1. Click on general to view the general diagnostics
See image 14-48.
Image 14-48
general diagnostics screen
How to check the advanced diagnostics ?
1. Click on advanced to view the advanced diagnostics
See image 14-49.
R5976491 IQ PRO G500 01/02/2007
147
14. IQ Network
Image 14-49
advanced diagnostics screen: green = OK ; red = error
14.7 Configuration
14.7.1 E-mail messaging
What can be done ?
E-mail messaging allows the projector to generate automatically E-mail and send them to three configurable recipients.
The mail can be sent on a regular basis i.e. daily, weekly or monthly or can be triggered by warnings.
Basically two different configurations must be done:
•
content
•
timing
Content configuration
The content configuration allows to define the content of the E-mail
•
general content
•
advanced content
Timing configuration
E-mail sending can be set to be time dependent or status dependent
•
daily : E-mail is sent every day, the time can be set
•
weekly: the day can be set with a calendar
•
on warning : a E-mail is sent whenever a warning is generated by the projector
14.7.2 E-mail configuration
How to configure the E-mail ?
1. Click on Configuration in the toolbar
2. Click on Mail Config to open the mail configuration screen
See image 14-50.
3. set the content by clicking the desired content (image 14-51)
4. set the timing by clicking the desired time interval
Note: if the timing is chosen to be monthly, a calendar is displayed , click the days on which the E-mail should be sent
148
R5976491 IQ PRO G500 01/02/2007
14. IQ Network
Image 14-51
Image 14-50
mail configuration screen
Mail “from” configuration
The “from” field of the received mails i.e. the name of the sender (in this case the iQ Pro server) can be configured in the server
software.
Therefore the E-mail address has to be filled in the Networking tab of the iQ Control Server properties dialogbox
Image 14-52
14.7.3 Projector Firmware Upgrade
What can be done ?
The client software allows to do an upgrade of the projector’s firmware.
The upgrade is done with a binary file (extension = “.bin”) which is sent to the projector using the LAN connection.
Single projector as well as multiple projector (group) upgrade is possible
How to upgrade the firmware ?
1. Click on Configuration in the toolbar
2. Click on Upgrade to open the firmware upgrade screen
See image 14-53.
3. Use the Browse key to select the desired bin file.
R5976491 IQ PRO G500 01/02/2007
149
14. IQ Network
4. Press the Upgrade button on the browser to select the file to start the operation (image 14-54)
5. Press the Upgrade button on the upgrade screen to start the operation
The information screen will show the progress of the operation.
Image 14-53
upgrade interface
Image 14-54
If the download doesn’t succeed please contact Barco
150
R5976491 IQ PRO G500 01/02/2007
14. IQ Network
14.8 DropZone
14.8.1 Dropzone tools
What can be done ?
The dropzone interface allows the user to manage (launch, store,...) presentation files from a local desktop.
Image 14-55
the DropZone interface
14.8.2 Start up
Start up
To start using the DropZone one must define the server (projector/display) to connect to. Several situations are possible.
1.
The projector/display to connect to has not yet been declared in the DropZone interface, in that case the projector/display has
to be added to the DropZone list using the Add function.
2.
The projector/display to connect to has already been declared in the DropZone, one must then just selected it from the list.
In case the projector/display name is not known, there is a possibility to select the projector.
by its location (only if the location has been specified).
How to open the installation menu ?
1. Click on the arrow to pull down the installation menu. (image 14-56)
See image 14-57.
Image 14-56
R5976491 IQ PRO G500 01/02/2007
151
14. IQ Network
Image 14-57
installation menu
How to add a projector to the list ?
1. Click on the three suspension points to open the projector selection dialog box. (image 14-58)
2. Click on the Add button.
A dialogbox is displayed. (image 14-59)
3. Enter the projector name or browse the network.
4. Click on OK.
5. Enter the Location (optional).
6. Click on Connect.
Following message is displayed : “Connected to <projectorname>...”
Image 14-59
Image 14-58
How to select an existing projector by its name ?
1. Click on the three suspension points to open the projector selection dialog box, image 14-58
2. Open the listbox and select the projector. (image 14-60)
the location will also be filled (if it has been entered previously).
3. Click on Connect.
Following message is displayed : “Connected to <projectorname>...”
Image 14-60
How to select an existing projector by its location ?
Can be useful when the projector name is not known.
1. Click on the three suspension points to open the projector selection dialog box, image 14-58
2. Open the listbox and select the location. (image 14-61)
152
R5976491 IQ PRO G500 01/02/2007
14. IQ Network
The projector name is filled in.
3. Click on Connect.
Following message is displayed : “Connected to <projectorname>...”
Image 14-61
This is only possible if the location has been filled, the default value for location being “<New Location>”
If the projector is not found following message will be displayed : “Host not found”
If the projector is found but unable to respond ( projector disconnected from the network, server software not
running, ...) following message will be displayed : “ Host found , but server inactive”
14.8.3 File dropping/launching
Only the Microsoft viewers (PPT, Word, Excel,...) are installed on the projector.
File dropping
Dropping a file means sending it to the projector using the DropZone interface.
The projector can then react in different ways depending on the drop mode selected :
•
launch file
•
launch file and share
•
store file on the projector
File launching
Launch files: a file stored on the projector (server) or on the network can be accessed from a local PC (via the network) or from the
projector itself. Launching a file means “sending and starting up” a file (using the required software).
A PowerPoint file can be launched on your PC and projected in another place (by default only the PPT viewer is installed on the
projector ).
for iQ only : The file will only be projected if the “iQ PC” is selected in the source selection.
How to set the drop mode ?
1. Open the DropZone interface.
2. Click on the arrow to pull down the installation menu.
3. Click on the three suspension points access the drop mode dialog box,image 14-57
See image 14-62.
4. Click on one of the three modes.
R5976491 IQ PRO G500 01/02/2007
153
14. IQ Network
Image 14-62
How to drop a file using the drag method ?
1. Drag the file into the drop window. (image 14-63)
The window opens and shows now the projector. (image 14-64)
2. release the mouse button.
The projector will then process the file according to the setting of the drop mode.
Image 14-64
Image 14-63
How to drop a file using the Open dialog box ?
1. Click on the upper button.
A browser is displayed. Choose a file to send to the projector.
The projector will then process the file according to the setting of the drop mode.
What to do with the launched files once disconnected ?
The previously dropped files are placed in a local directly on the server, one may choose to delete them or not.
1. Click on the arrow to pull down the installation menu.
2. Click on the Options button.
A dialog box is displayed. (image 14-65)
3. Check the box to destroy the launched files once disconnected.
Image 14-65
154
R5976491 IQ PRO G500 01/02/2007
14. IQ Network
14.8.4 Open remotely a file on the projector
How to open a file on the projector ?
1. Click on the lower button of the DropZone interface
A browser is displayed. Select the file to be projected.
for iQ only: The file will only be projected if the “iQ PC” is selected in the source selection.
14.8.5 Remote desktop sharing (virtual meeting)
What can be done ?
The remote desktop sharing in the DropZone allows to visualize the projected image i.e. the desktop of the projector PC on a local
PC.
Besides Desktop sharing one can take the Control (mouse and keyboard control) over a presentation (using Netmeeting TM). The
control over the presentation can be taken or passed at any time.
The configuration consisting of several remote or local meeting participants sharing the same information content is called a virtual
meeting.
In this virtual meeting each meeting participant can participate to the meeting either in a passive way, by following the meeting on
his local desktop (remote desktop sharing), or in an active way by controlling the server’s desktop (mouse and keyboard).
Control over the desktop can be requested, forwarded or released.
R5976491 IQ PRO G500 01/02/2007
155
14. IQ Network
1
3
3
2
2
1
1
IQ Pro Server desktop Control
2
3
Image 14-66
Virtual Meeting
1
2
3
forward control
release control
request control
How to perform remote desktop sharing ?
1. Click on the middle button
The middle button indicates the activation of the remote
The desktop is displayed on the local PC monitor. (image 14-67)
156
R5976491 IQ PRO G500 01/02/2007
14. IQ Network
Image 14-67
remote desktop sharing in case of a PowerPoint TM presentation
How to take (mouse and keyboard)Control over the desktop ?
1. Click on the Control menu
The Control menu is displayed (image 14-68)
2. Select the Request Control item
The desktop can now be remote controlled.
Image 14-68
The control over the desktop is now done by the local PC. However, the user can at any time decide to release
or forward the control to someone else.
How to release control over the desktop ?
1. Click on the Control menu
The Control menu is displayed (image 14-69)
2. Select the Release Control item
The desktop remote control can now be requested by someone else.
R5976491 IQ PRO G500 01/02/2007
157
14. IQ Network
Image 14-69
How to forward control over the desktop ?
1. Click on the Control menu
The Control menu is displayed (image 14-70)
2. Select the Forward Control item
A pop up menu shows the meeting participants i.e. the users which are connected to the server and which participate to the
Remote sharing of the desktop.
3. Select the meeting participant
The control is transferred and the user which has the control is know indicated in the title bar.
Image 14-70
14.8.6 DropZone settings
What can be done ?
The Server settings on the Projector allow to configure the DropZone in several ways:
•
Disallow new meeting participants: New meeting participants will not be able to request desktop sharing or desktop control.
•
Disallow Launch file: Launching a file with the DropZone will be impossible when activating this setting, hereby preventing
undesired content to be projected during a meeting.
•
Enable/disable desktop sharing at startup or logon.
How to setup the DropZone ?
1. Go to the server icon in the lower task bar of the server desktop and Click the right mouse button.
A menu is displayed (image 14-71)
2. Select Settings
3. Select the DropZone tab (image 14-72)
4. Check the desired settings
158
R5976491 IQ PRO G500 01/02/2007
14. IQ Network
Image 14-71
Image 14-72
Choosing True color as color depth setting will slow down the communication.
It is advised to leave the other Server properties as they are. If necessary Contact your IT administrator.
14.9 The Web client
Web based functionality
The aim of the web services is to allow each network client within the LAN environment to browse via its internet browser to the web
client.
This may be seen as an alternative to the client software since the main control & diagnostic tools are also present. Its advantage
resides in the fact that no software has to be installed on the local PC, the internet takes while the html page generation is done
locally on the server.
How to access the web client via the internet browser ?
To access the web client, the http link has to be filled in on the client’s internet browser.
This http link contains the name of the projector/display i.e. the name under which it is identified within the LAN.
R5976491 IQ PRO G500 01/02/2007
159
14. IQ Network
Image 14-73
Web interface
What can be done ?
The possibilities are mainly the same as on the client software.
The web interface allows a user friendly way to manage the projector/display, its use being straightforward and similar to the client
interface (ref).
Requirements for the use of the Web client
Some components have to be installed or enabled on your local (client) operating system to allow access to
the Web client.
See the Appendix “ General guidelines on network configuration” for general guidelines on how to enable
these services. .
The minimal server software version should be V1.10 to allow the use of the Web client.
160
R5976491 IQ PRO G500 01/02/2007
15. General guidelines on Network Configuration
15. GENERAL GUIDELINES ON NETWORK
CONFIGURATION
Overview
•
General Network
•
The Internet and Web services
The installation of the iQ Pro in a Local Area Network must be done in the same way as the installation of
a standard PC in that particular network meaning that the same rules and accepted practice should be respected.
The assistance of qualified IT personnel is advised.
15.1 General Network
An Administrator password has been installed for security reasons (worm and virus protection):
Password : Barco (case sensitive !)
Microsoft NT Domain
To enable access to your network resources, the iQ Pro must be a member of your NT Domain.
This can be configured in the Control Panel, under “System”, in the “Computer Name” tab, under the button “Network ID”. You’ll
need some help from the Network Administrator, since you need special rights to do this.
TCP/IP
The iQ Pro uses TCP/IP networking, so it needs the IP address, network mask, broadcast address, gateway, dns, wins, etc. to be
configured. This can be done in the Control Panel, under “Network Connections”. This can however be configured automatically, if
your network uses DHCP.
15.2 The Internet and Web services
Internet access
If you want to access the Internet from the iQ Pro, and the projector is located behind a firewall, you will also need to configure
the proxy to use. This can be done in the Control Panel, under “Internet Options”, in the tab “Connections”, under the button “LAN
Settings”.
iQ Pro Web services
To use the iQ Pro web client, you might need to change the “LAN Settings” on your local computer
If the client thinks the projector is on the Internet, and tries to connect to it through the proxy, you can turn on the “Bypass proxy
server for local addresses” feature, or add the projector to the Exceptions list under the “Advanced” button.
The “Internet Information Services(IIS) ” component has to be installed on the operating system.
SNMP
To enable management via the IQProSNMP Agent, you must enable the SNMP system service, and configure the communities
accordingly.
This can be done in the Control Panel, under Administrative Tools, in the Services, under the entry “Management and Monitoring
tools”. You may also need to enable SNMP in the iQ Pro Control Server in de suystem tray, see image below.
R5976491 IQ PRO G500 01/02/2007
161
15. General guidelines on Network Configuration
Image 15-1
system tray
Image 15-2
server settings dialog box
For more info, see "SNMP services", page 171
Microsoft Exchange and Outlook
To enable control via the Microsoft Exchange integration, you need to install, enable and configure the IQProEXCH module.
To enable control from Microsoft Outlook, you need to install, enable and configure the IQProEXCH module, and install an Outlook
Form on the Exchange Server in your network.
For more info, see "Exchange", page 163
162
R5976491 IQ PRO G500 01/02/2007
A. Exchange
A. EXCHANGE
Introduction
Some parameters values are installation dependent, and are shown here as an example.
You may need assistance from you network administrator, IT Manager or MIS helpdesk to obtain the settings or to configure
the projector for you, since this is a task description targeted to ‘Administrators’ and needs knowledge and/or permissions
normally held by those persons.
It is advised that you first try to follow the procedure to obtain a working setup, before changing the settings for conforming to your
local security requirements.
Use of this software requires a working Microsoft Exchange server installed somewhere in your corporate network.
A.1
Exchange Installation
A.1.1
Installation procedure
Creating a user account and mailbox
1. Create a user account in your NT Domain (on the projector).
The service will use this account to log on to the domain, and as credentials to authenticate to Microsoft
Exchange to read the entries in the Calendar folder of the Mailbox.
Username: iqpro
Domain: BARCO
Password: pwiqpro
2. Create a Mailbox for the projector’s account on the Microsoft Exchange Server (on your LAN).
The NT Domain user created in step 1 should have read access to this Mailbox.
Server: “BARCOEXCHSRV”
Mailbox: “Projector, IQPRO”
User: BARCO\iqpro
Installing and configuring Microsoft Outlook (on the projector)
1. Install Microsoft Outlook on the Projector.
Note: To be able to access Microsoft Exchange, you need a Client Access License.
Once you have one of those, you also have a license to Microsoft Outlook.
Refer to the following URL for more information: http://www.microsoft.com/resources/sam/licensing/cal_guide/exchange.asp
Tip:
Outlook can be installed from the Microsoft Exchange Server CDROM or from a Microsoft Office Suite Installation
CDROM.
Since the IQ Pro has no CDROM drive, you may need to use a CDROM drive shared from a PC in the network.
Alternatively, you could use a USB CDROM drive.
2. Make sure the projector is part of the domain
Tip:
This can be done in Control Panel->System->Computer Name->Change
3. Log in on the projector as the user
User: iqpro
Domain: BARCO
Password: pwiqpro
Tip:
If the user cannot log on, the Local Administrator should add the right “Log on locally” for the user.
This must be configured in Start->Control Panel->Administrative Tools->Local Security Policy
4. Configure Outlook
Profile Name: “MS Exchange Settings”
This is what the wizard proposes by default, and what is used in this document.
Default Mail Client: yes
Note: Make sure that MS Outlook is the default Mail Client for this account.
You can do this afterwards from this configuration page: Start->Control Panel->Internet
Options->Programs->Email For more information, refer to :
http://www.microsoft.com/mspress/troubleshooting/outlook/LS/101801.asp
Enabling the account
1. Log on to the projector as an Administrator for the next steps.
R5976491 IQ PRO G500 01/02/2007
163
A. Exchange
For security reasons, you will probably not want to make the projector account part of one of the
administrator groups.
2. Enable the account to be used by the “iQ Pro Exchange Integration” service
3. In the Tree of the “Local Security Settings” application, navigate to Security Settings->Local Policies->User
Right Assignment.
4. In the List, edit the “Log on as a service”, and add the account, in the example “BARCO\iqpro”.
Installing and configuring the iQProEXCH service
Step 1,2,3 refers to the manual installation. One can use the SETUP.EXE program instead.
1. Copy the file IQProEXCH.EXE to (eg.) C:\Program Files\BARCO\iQ Pro Server
2. Open a command line, and go to the that directory
3. Type the following command IQProEXCH /Service
4. To configure, right click the “IQ Pro Server” tray icon, and go to the tab “Exchange”
Enter the credentials (image A-1, image A-2)
5. To enable the “IQProEXCH” service go to Control Panel->Administrative Tools->Services->IQPro Exchange
go to the TAB “General Startup” and Type: Automatic
Make the service use the correct account TAB Log On
Select “Local System Account”
Check “Allow service to interact with desktop”
6. Start the service, or reboot the projector.
Image A-1
system tray
Image A-2
server exchange tab
You should now be able to schedule commands from a Microsoft Exchange client such as Outlook
running on any computer on the local network, provided you have the necessary permissions on the
Calendar in the projector mailbox.
A.1.2
Troubleshooting
The file C:\Program Files\BARCO\IQ Pro Server\IQProEXCH.log and the “Event Log” may contain helpful information to diagnose what’s going wrong
What can go wrong and what to do ?
1. The log file contains “Logon failure: unknown user name or bad password”
Check Username, Password and Domain in Control Server/Exchange
2. The log file contains “Logon failure: the user has not been granted the requested logon type at this computer.”
The user account must be given the “Log on as a service” permission. This is done in Start/Control
Panel/Administrative Tools/ Local Security Settings/Security Settings/Local Policies/User Right
164
R5976491 IQ PRO G500 01/02/2007
A. Exchange
Assignment. In the list, add the user to the entry “Log on as a service”
3. The log file contains “Could not log on with Profile ’MS Exchange Settings’” Make sure the profile exists. To check this, log
in to the projector as the user (BARCO\iqpro), as the profile should be owned by the projector account, and Outlook-profiles are
per-account. Start/Control Panel/Mail
4. The user cannot log on to the projector. The Administrator should add the right “Log on locally” for the user. This must be
configured in the Start/Control Panel/Administrative Tools/Local Security Policy
In the list, add the user to the entry “Log on as a service”
5.
When trying to start the service, the projector beeps, and the service stays in the ‘starting’ state
This happens when the service tries to display an error in a popup, but cannot access the desktop. Control
Panel/Administrative Tools/Services/IQPro Exchange
Check “Allow service to interact with desktop”
You may need to end the process ‘IQProEXCH’ from the task manager.
6. The commands are not executed at the right time
Check the time of the computer and the timezone Start/Control Panel/Date and Time/Timezone
7. An Outlook dialog box is displayed stating that there is no default mail client.
Make sure that MS Outlook is the default Mail Client for this account. You can do this from this
configuration page: Start/Control Panel/Internet Options/Programs/Email
You may need to do this as administrator, since the service is started as ‘Local System’ account.
Tip:
For more information, refer to http://www.microsoft.com/mspress/troubleshooting/outlook/LS/101801.asp
A.2
Exchange Integration
Introduction
The projector must be configured to connect to a mailbox on a Microsoft Exchange server in the network, which is dedicated to the
projector, and to which of course the projector has rights to connect to.
The commands should be put in the SUBJECT of an appointment in the Exchange Calendar of the projector. The Start Time and
End Time of the appointments are used for timing info. The other fields (location, categories, body, … ) are not used by the software,
and thus can be used to store extra information for the USERS of the projector mailbox.
A.2.1
Command
How are the commands build up ?
•
Command filename/filepath
The parameter filename is a filename relative to the “Receive” directory of the iQ Pro Control Server, which, in a default installation,
would typically be the local folder “C:\Documents and Settings\All Users\Received” The parameter filepath is an absolute path to a
file.
The commands should be put in the SUBJECT of an appointment in the Exchange Calendar of the projector. This is a mailbox on
a Microsoft Exchange server in the network, which is dedicated to the projector, and to which of course the projector has rights to
connect to.
The command and the filename are separated by a space.
R5976491 IQ PRO G500 01/02/2007
165
A. Exchange
Overview of the commands
•
ON
•
STANDBY
•
PAUSE
•
PAUSE ON
•
PAUSE OFF
•
LOGO
•
LOGO ON
•
LOGO OFF
•
SWITCH SOURCE
•
SWITCH LAYOUT
•
LAUNCH ATTACHMENT
•
STORE ATTACHMENT
•
STORE filename
•
STORE FILE filepath
•
LAUNCH filename
•
LAUNCH FILE filepath
•
DELETE filename
•
DELETE FILE filepath
ON, STANDBY
The projector is put in the specified state at the beginning of this event. Beware that if the SBC (Single Board Computer) is to be
powered-down during STANDBY, that further events will not be processed, since the integration runs on that SBC.
PAUSE, LOGO
The projector is put in the specified state at the beginning of this event, and the state is undone at the end of this event. o A parameter
ON or OFF can be specified to choose between the actions. This action will then be executed at the beginning. So “PAUSE from
12:00 to 13:00” is equivalent to “PAUSE ON at 12:00” + “PAUSE OFF at 13:00”
SWITCH SOURCE, SWITCH LAYOUT
The projector switches source or layout at the beginning of this event.
LAUNCH ATTACHMENT
The attachment is saved at the beginning of this event. Then the associated application is started. o At the end of the event, the
application is killed. This can not be guaranteed if the application was already running on the projector. For example, if a web page
is being displayed, and a second one is launched, the application is not started, but the original browser displays the page. In this
case the second event can not control the browser. This is a limitation of the Windows platform.
STORE ATTACHMENT
The attachment is saved at the beginning of this event. The name of the attachment is used and the file is placed in the Receive
folder.
STORE filename
The attachment is saved at the beginning of this event. The name filename is used and the file is placed in the Receive folder. For
example “STORE MYFILE.PPS” will save the attached file to “C:\Documents and Settings\All Users\Received\MYFILE.PPS”
STORE FILE filepath
The attachment is saved at the beginning of this event. The path filepath is used as absolute filename. For example, the command
“STORE FILE C:\My Videos\MYFILE.AVI” will store the attachment as C:\My Videos\MYFILE.AVI. This of course if permissions are
correct and the directory C:\My Videos exists
DELETE filename
The file with name filename is deleted from the receive folder. For example “DELETE MYFILE.PPS” will delete “C:\Documents and
Settings\All Users\Received\MYFILE.PPS”
DELETE FILE filepath
The file with absolute name filepath is deleted. For example, the command “DELETE FILE C:\My Videos\MYFILE.AVI” will store the
attachment as C:\My Videos\MYFILE.AVI.
Drop down list
Besides the above commands some predefined commands can be selected from a drop down list in the iQPro tab.
166
R5976491 IQ PRO G500 01/02/2007
A. Exchange
Image A-3
A.2.2
Example
Schedule projector tasks in Microsoft Outlook 2000
following tasks are scheduled:
Image A-4
1.
store attachment at 12:30 (The attached file is iQ_Pro_brochure.pdf)
2.
turn the projector on at 13:00 and launch a different attached file
3.
show the logo from 14:29 to 14:31 to hide the killing of the application and the starting of the PDF Viewer
4.
at 14:30, lauch the PDF file that was stored in step 1 5
5.
kill the application and put the projector in standby at 16:00
6.
delete the PDF file that was stored in step 1
A.2.3
Microsoft Outlook Integration
Adding Outlook forms
To make things easier for users, you can install an Outlook Form that adds a tab called “iQ Pro” to the appointment. The form
contains the most-used commands in easy-to use drop-down lists. It looks as follows:
R5976491 IQ PRO G500 01/02/2007
167
A. Exchange
Image A-5
The form contains the functionality that a normal user should be able to use without consulting the documentation.
The attachments, date and time fields must be edited in the “Appointment” tab.
Choosing items from the drop-down boxes fills in the subject.
By default, the layouts “Full-screen” and “2by2 raster” are defined in the form.
If you add layouts on the projector(s) or change the defaults, the user must type the name of the layout in the subject.
The form can be modified to make things easier for users, one can also add the defined layouts to the drop-down list. This must be
done from Outlook, in the menu “Tools->Forms->Design This Form”
Organizational Forms
The administrator should install Organizational Forms on the Exchange Server in the “Organizational Forms”
library.
Default form
Now the form still needs to be set as a default for creating new items. When returning to the “Forms” tab in the “Calendar Properties”
you should now see the “iQ Pro” template installed. Now go to the “General” tab and select the template as default for posting to
the folder.
Image A-6
If the form was installed as an “Organizational Form”, you need to select the “Forms…” entry, which will display the “Choose Form”
dialog,
168
R5976491 IQ PRO G500 01/02/2007
A. Exchange
Image A-7
A.2.4
Folder form
Folder form
Alternatively, the form can be installed for the Calendar folder only, by following the procedure described below
How to configure a folder form
1. In outlook, right-click on the “Calendar” icon in the “Outlook Shortcuts” tab in the “Outlook Bar” to open the “Properties” page,
while logged-on as the projector (Or display the “Folder List”, and right-click the “Calendar” folder to open the “Properties” page).
2. In the “Calendar Properties” dialog, go to the “Forms” tab, and click the “Manage…” button. (image A-8)
3. On the “Forms Manager” dialog, click the “Install…” button and select the file “iQ Pro.fdm”. (image A-9)
4. When returning to the “Forms” tab in the “Calendar Properties” you should now see the “iQ Pro” template installed.
Now go to the “General” tab and select the template as default for posting to the folder. (image A-10)
Image A-9
Image A-8
R5976491 IQ PRO G500 01/02/2007
169
A. Exchange
Image A-10
A.2.5
Limitations and known “problems”
Overlapping tasks
When launching 2 attachments with overlapping times it is possible for the application to exit at the end of the first period. For
example, let’s say we try to display PRES1.PPT from 12:00 to 13:30, and PRES2.PPT from 13:00 to 14:30, it is possible for BOTH
presentations to exit at 13:30. This is because Windows uses the same process to display both files, and activates them via DDE.
Image A-11
This is a limitation in the Microsoft Windows ShellExecuteEx API
Avoid overlapping schedules in this case, or change the associations in: My Computer->Tools->Folder Options->File Types->(extension)
Try to disable DDE (under Edit with the default action, eg ‘open’, selected) and/or disable ‘Browse in same
window’ or using a different viewer/player for the file type.
170
R5976491 IQ PRO G500 01/02/2007
B. SNMP services
B. SNMP SERVICES
Introduction
Some parameters values are installation dependent, and are shown here as an example.
You may need assistance from you network administrator, IT Manager or MIS helpdesk to obtain the settings or to configure
the projector for you, since this is a task description targeted to ‘Administrators’ and needs knowledge and/or permissions
normally held by those persons.
It is advised that you first try to follow the procedure to obtain a working setup, before changing the settings for conforming to your
local security requirements.
B.1
SNMP installation
Introduction
The Control Server version should be at least version 1.10.
To check the version, open the about box from the server tray:
Software updates can be obtained from the BARCO support website: ftp://ftp.barco.com/pub/iq_pro_software/
or from secured website PartnerZone
How to install SNMP (only if necessary)
1. The Microsoft SNMP service must be installed
You may need to install this service from the Windows XP CDROM.
2. Install the SNMP Agent Extension dll regsvr32 IQProSNMP.dll
The agent should now be registered as “iqpro” under
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\SNMP\Parameters\ExtensionAgents
How to configure SNMP (only if necessary)
1. Go to the Control panel, under the Administrative Tools, in the Services, in the “SNMP” entry.
2. In the “General” tab, you can enable the service, and make it start automatically.
3. In the “Security” tab, the default Community is called ‘public’ and is read-only.
You may want to give read-write permission to ‘public’ (not recommended) or create a ‘private’ community
with read-write permissions.
4. In the Control Server, enable the SNMP support, and optionally, enable read-write support.
5. The SNMP service should be restarted, to take the changed settings into account.
To uninstall the snmp agent: regsvr32 /u IQProSNMP.dll
B.2
SNMP integration
Commands
Following commands are provided stored in the MIB :
Command
Type
PROJECTORTYPE
READ
SERIALNUMBER
READ
R5976491 IQ PRO G500 01/02/2007
171
B. SNMP services
172
Command
Type
LAMPPRODUCTNUMBER
READ
LAMPSERIALNUMBER
READ
SERVERTYPE
READ
SERVERVERSION
READ
EMBEDDEDSOFTWAREVERSION
READ
PROJECTORLANGUAGE
READ
PROJECTORNAME
READ
LOCATION
READ
ORIENTATION
READ
RESOLUTION
READ
DESKTOPRESOLUTION
READ
PROJECTORSTATE-cooldown
READ
PROJECTORSTATE-textbox
READ
PROJECTORSTATE-projector
READ/WRITE
PAUSE
READ/WRITE
FREEZE
READ/WRITE
PROJECTORRUNTIME
READ
LAMPWARNINGSTATUS
READ
LAMPALERTSTATUS
READ
LAMPMODE
READ/WRITE
LAMPRUNTIME
READ
LAMPSTATUS
READ
LAMPWARNINGTIME
READ/WRITE
I2CDIAGNOSTICS
READ
POWERSUPPLYERROR
READ
LAMPERROR
READ
PCSTATEPROJECTORON
READ/WRITE
PCSTATEPROJECTORSTANDBY
READ/WRITE
PCSTATE
READ/WRITE
R5976491 IQ PRO G500 01/02/2007
C. Troubleshooting
C. TROUBLESHOOTING
An Administrator password has been installed for security reasons (worm and virus protection):
Password : Barco (case sensitive !)
FAQ table
This table gives a summary of possible errors, the aim of this section is to give general guidelines and tips for troubleshooting.
C.1
FAQ table
What to do when... ?
Symptom
Possible cause
Check
The projector is working
(operational mode) but Server
is not running
•
The Projector ON state
setting ( in the “iQ Pro
Server settings” menu)
•
The setting should be
“ON”
•
The Projector Standby
state setting ( in the “iQ Pro
Server settings” menu)
•
The setting should be
“ON”
No client/server communication
in case of a point to point
communication
•
IP address is not filled in
correctly
•
IP address
No client/server communication
over the LAN
•
Client configuration
•
Client configuration:
projector name
When using the DropZone, the iQ
Pro server does not accept calls
from client(s)
•
Netmeeting TM settings are
incorrect
•
Netmeeting TM settings
When using the DropZone it is
impossible to launch/store files
•
No access the shared
folder “Received”
•
check guest account
settings in Windows TM
PC card is not working or influences
the good working of the SBC
•
incompatible PC card
•
Check if the PC card
driver is compatible with
Windows TM XP
The projector is in standby mode
and the Server is not running
R5976491 IQ PRO G500 01/02/2007
References
IT administrator
IT administrator
IT administrator
IT administrator
173
C. Troubleshooting
174
R5976491 IQ PRO G500 01/02/2007
D. Cleaning the dustfilters
D. CLEANING THE DUSTFILTERS
Overview
•
Dustfilters
•
Cleaning
D.1
Dustfilters
Location of the filters
There are 4 filters located at different positions
1.
Filter1: Lamp 1
2.
Filter2 : Lamp 2
3.
Filter 3 : X-Cube filter
4.
Filter 4 : Input filter
Image D-1
location of the filters
1
2
3
4
D.2
lamp filter 1
lamp filter 2
x-cube filter
input filter
Cleaning
How to clean the dustfilters ?
1. Place the projector so as to access easily the filter to be cleaned
2. Push the handle downwards to unlock the filter. (image D-2)
3. Slide out the filter (image D-3, image D-4, image D-5)
See image D-6.
4. Clean the dust filter with a dry cloth.
5. Re-insert the dust filter by sliding it back in the filter housing.
Image D-2
Location of the x-cube filter and its handle
R5976491 IQ PRO G500 01/02/2007
175
D. Cleaning the dustfilters
Image D-4
lamp & X-Cube filters removed
Image D-3
Lamp filter removal
Image D-6
Input filter removed
Image D-5
Input filter removal
If the airflow is falling under a predetermined treshold value a warning will be displayed on the screen.
Image D-7
At that time it is strongly recommended to replace or clean the dustfilter under the X-cube. Failing to do so,
will strongly reduce the lifetime of the LCD’s and the analyzers.
The manufacturer reserves itself the right to refuse warranty repair if the projector was working with dirty
dustfilters.
176
R5976491 IQ PRO G500 01/02/2007
E. Standard Image Files
E. STANDARD IMAGE FILES
E.1
Table overview
Table overview
The following standard image files are pre-programmed in the projector.
Name5
Resolution6
Fvert
FHor
Fpix
Hz7
kHz8
MHz9
Ptot10
Pact11
Ltot12
Lact13
1600_48V
1600x600i
48,040
62,500
135,000
2160
1600
651
600
CGA
640x200i
59,924
15.700
14.318
912
640
262
200
COMPUSC4
1024x480i
29,945
30,694
39,779
1296
1024
512
480
DOS1_70
720x400
70
31,500
28,350
900
720
449
400
DOS3_56
640x400
56
24,800
21,030
848
640
440
400
DOS4_85
640x400
85
37,860
31,500
832
640
445
400
ED
735x480
59,943
31,470
28,638
910
735
525
480
EGA
640x350
59,702
21,851
16,257
744
640
366
350
ESVGA_75
832x624
73
47,900
53,648
1120
832
660
624
EXGA_60
1152x864
60
54,900
79,934
1456
1152
916
864
EXGA_80
1152x864
80,000
76,499
110,159
1140
1152
958
864
EXGA_85
1152x864
85
77,202
121,671
1576
1152
907
864
,000
EXGA1_70
1152x864
70
63,800
94,424
1480
1152
912
864
EXGA1_75
1152x864
75
67,499
107,999
1600
1152
900
864
EXGA2_70
1152x864
70
66,098
99,941
1512
1152
945
864
EXGA2_75
1152x864
75
75,199
110,092
1464
1152
1002
864
FMR
640x400i
42,323
36,440
28,570
784
640
431
400
GE_50
640x400
50
31,200
44,928
1440
1163
625
522
GE_60
1085x480
60
30,700
41,261
1344
1085
512
480
hd_1080i
1920x540
60
33,750
74,249
2200
1920
563
540
hd_24p
1920x1080
24,000
27,000
74,000
2750
1920
1125
1080
hd_24sf
1950x540
48,000
27,000
74,000
2750
1950
562
540
hd_25i
1920x540
50,000
28,125
74,000
2640
1920
562
540
hd_25p
1920x1080
25,000
28,125
74,000
2640
1920
1125
1080
5. Name: name of file, contains the settings.
6. Resolution: image resolution, when followed by ..i means interlaced.
7. Fvert Hz: vertical frame frequency of the source
8. FHor kHz: horizontal frequency of the source
9. Fpix MHz: pixel frequency
10. Ptot : total pixels on one horizontal line.
11. Pact: active pixels on one horizontal line.
12. Ltot: total lines in one field
13. Lact: active lines in one field.
R5976491 IQ PRO G500 01/02/2007
177
E. Standard Image Files
Name5
178
Resolution6
Fvert
FHor
Fpix
Hz7
kHz8
MHz9
Ptot10
Pact11
Ltot12
Lact13
hd_30p
1920x1080
30,000
33,750
74,000
2200
1920
1125
1080
hd_60p
1280x720
60,000
45,000
74,000
1650
1280
750
720
INTER_GR
1184x886
67,170
61,796
92,941
1504
1184
920
886
IQPC_SXGA_2
1366x1024
59
62,933
106,230
1688
1366
1067
1024
IQPC_SXGA_D
1280x1024
60
63,857
107,791
1688
1280
1063
1024
IQPC_XGA_1
1024x768
61
49,005
65,863
1344
1024
807
768
IQPC_XGA_2
1024x768
60
48,485
65,164
1344
1024
807
768
IQPC_XGA_D
1024x768
61
49,005
65,863
1344
1024
806
768
MAC_3
512x384
60,147
24,480
15,667
640
512
407
384
MAC_4
560_384
60,147
24,480
17,234
704
560
407
384
MAC_5
512x342
60,158
22,259
16,670
704
512
370
342
MAC_6
832x624
74,546
49,722
57,280
1152
832
667
624
MAC_7
1024x768
74,907
60,150
80,000
1330
1024
803
768
MAC_LC
640x480
66,619
34,975
31,338
896
640
525
480
MAC_POR
640x870
74,996
68,846
57,280
932
640
918
870
METH_BOOT1
720x400
70
31,500
28,350
900
720
448
400
METH_BOOT2
640x480
59
31,000
24,800
800
640
524
480
MXGA_100
1152x864
100
92,997
145,820
1568
1152
930
864
NTSC
675x240
60
15,748
13,512
858
675
263
240
NTSC_LIMO_x2
834x482
60
31,496
32,252
1024
834
525
482
NTSC_LIMO_x3
834x715
60
46,646
47,766
1024
834
778
715
NTSC_LIMO_x4
834x961
60
62,992
64,504
1024
834
1050
961
PAL
675x286
50
15,625
13,500
864
675
313
286
PAL_LIMO_x2
834x574
50
31,250
32,000
1024
834
626
574
PAL_LIMO_x3
834x850
50
46,296
47,407
1024
834
926
850
PAL_LIMO_x4
834x1146
50
62,500
64,000
1024
834
1250
1146
PAM500
640x400
60,000
26,400
22,810
864
640
440
400
PAM800
1120x375i
44,936
36,443
50,000
1372
1120
406
375
PC98_2
1120x375i
39,994
32,835
47,840
1457
1120
411
375
PC98_3
1120x750
60,000
50,000
78,569
1571
1120
833
750
S1152_66
1152x900
66,004
61,846
94,500
1528
1152
937
900
S1152_76
1152x900
76,637
71,809
108,000
1504
1152
937
900
R5976491 IQ PRO G500 01/02/2007
E. Standard Image Files
Name5
Resolution6
Fvert
FHor
Fpix
Hz7
kHz8
MHz9
Ptot10
Pact11
Ltot12
Lact13
S1600_67
1600x1280
67
89,286
200,000
2240
1600
1334
1280
SDI_625
675x278i
25,000
15,625
13,500
864
720
313
278
SDI_525
675x240i
29,970
15,734
13,500
858
720
263
240
SG_50
1600x1200
50,000
62,500
130,313
2085
1600
1250
1200
SG_60_1
1280x1024
60,000
63,900
107,352
1680
1280
1065
1024
SG_60_2
1024x768
60,000
48,780
64,390
1320
1024
813
768
SG_60_3
960x680
60,000
43,200
54,432
1260
960
720
680
SG_60_4
1600x1200
60,000
75,000
156,375
2085
1600
1250
1200
STOR_100
764x287
100
31,300
30,361
970
764
313
287
STOR_120
810x247
119
31,300
30,361
970
810
263
247
STOR_50
1024x512
50
31,300
40,064
1280
1024
625
512
STOR_60
1024x512
60
31,300
40,064
1280
1024
525
512
SUNEWS67
1280x1024
67,189
71,691
117,000
1632
1280
1067
1024
SUNEWS76
1280x1024
76,107
81,130
135,000
1664
1280
1066
1024
SUNXGA60
1024x768
59,984
48,287
64,125
1328
1024
805
768
SUNXGA70
1024x768
70,041
56,596
74,250
1312
1024
808
768
SUNXGA77
1024x768
77,069
62,040
84,375
1360
1024
805
768
SUP_MAC
1024x768
60,000
48,780
63,999
1312
1024
813
768
SVGA_56V
800x600
56,250
35,156
36,000
1024
800
625
600
SVGA_60V
800x600
60,317
37,879
40,000
1056
800
628
600
SVGA_72_1
800x600
72,084
48,080
50,003
1040
800
666
600
SVGA_72_2
800x600
72,084
48,080
50,003
1040
800
667
600
SVGA_75
800x600
75,000
46,875
75,000
1056
800
625
600
SVGA_85
800x600
85,000
53,635
56,250
1048
800
631
600
SXGA_72_1
1280x1024
72
76,699
128,854
1680
1280
1061
1024
SXGA_72_2
1280x1024
72
76,970
130,080
1690
1280
1069
1024
SXGA_75
1280x1024
75
79,974
134,997
1688
1280
1066
1024
SXGA_76
1280x1024
76
81,103
134,955
1664
1280
1066
1024
SXGA_85
1280x1024
85
91,149
157,506
1728
1280
1072
1024
SXGA_L
1280x1024
60
62,500
84,000
1344
1280
1041
1024
R5976491 IQ PRO G500 01/02/2007
179
E. Standard Image Files
Name5
180
Resolution6
Fvert
FHor
Fpix
Hz7
kHz8
MHz9
Ptot10
Pact11
Ltot12
Lact13
SXGA+_60
1280x1024
60
63,980
107,997
1688
1280
1066
1024
SXGA2_60
1280x960
60
59,999
107,998
1800
1280
1000
960
SXGA2_85
1280x960
85
85,940
148,505
1728
1280
1011
960
SXGA50
1280x1024
50
52,351
88,368
1688
1280
1047
1024
SXGA60v
1280x1024
60
63,658
110,001
1728
1280
1056
1024
SXGAP_70
1024x1280
70
92,902
133,779
1440
1024
1326
1280
SXGAP1_60
1024x1280
60
77,700
83,916
1080
1024
1297
1280
SXGAP2_60
1024x1280
60
79,498
110,661
1392
1024
1325
1280
UXGA_60
1600x1200
60
75,002
162,004
2160
1600
1250
1200
UXGA_65
1600x1200
65
81,248
175,496
2160
1600
1250
1200
UXGA_L
1600x1200
60
72,801
119,977
1648
1600
1216
1200
UXGAP1_60
1200x1600
59
95,804
119,946
1252
1200
1620
1600
UXGAP2_60
1200x1600
60
99,404
163,817
1648
1200
1656
1600
VGA_60
640x480
60
31,326
25,061
800
640
525
480
VGA_66
640x480
67
35,100
30,326
864
640
525
480
VGA_72
640x480
73
37,860
31,500
832
640
520
480
VGA_75
640x480
75,000
37,500
31, 500
840
640
500
480
VGA1_85
640x480
85,000
43,369
36,000
832
640
509
480
VGA2_85
720x400
85,000
37,900
35,475
936
720
446
400
VGA75ISO
640x480
75,000
39,375
31,500
800
640
525
480
VIDEO525
1302x239i
29,970
15,734
32,207
1302
1024
263
239
VIDEO625
1024x278i
25,000
15,625
31,984
1310
1024
313
278
XGA_43
1024x384
87
35,500
44,872
1264
1024
409
384
XGA_60
1024x768
60,000
48,360
64,996
1344
1024
806
768
XGA_70_1
1024x768
70,000
56,475
74,999
1328
1024
806
768
XGA_70_2
1024x768
70,000
57,052
78,047
1368
1024
815
768
XGA_72
1024x768
71,955
58,140
80,000
1376
1024
808
768
XGA_75_1
1024x768
75
60,024
78,752
1312
1024
800
768
XGA_75_2
1024x768
76
61,080
86,000
1408
1024
806
768
XGA_85
1024x768
85,000
68,680
94,500
1376
1024
808
768
R5976491 IQ PRO G500 01/02/2007
E. Standard Image Files
Name5
Resolution6
Fvert
FHor
Fpix
Hz7
kHz8
MHz9
Ptot10
Pact11
Ltot12
Lact13
XGA_EOS
1024x768
63,000
50,000
67,200
1344
1024
796
768
XGA75_GS
1024x768
74,534
59,701
79,284
1328
1024
801
768
SXGA_60
1280x1024
60
63,980
107.997
1688
1280
1066
1024
SXGA+_60_2
1400x1050
60
65,574
122,230
1864
1400
1089
1050
SXGA+_60_3
1400x1050
60
65,104
122,396
1880
1400
1085
1050
Table E-1
R5976491 IQ PRO G500 01/02/2007
181
E. Standard Image Files
182
R5976491 IQ PRO G500 01/02/2007
Glossary
GLOSSARY
AGC
Automatic Gain Control: allows an automatic amplitude (gain) control of the incoming video signal
ANSI 73.11
American power plug to connect the power cord to the wall outlet.
CEE7
European power plug to connect the power cord to the wall outlet.
Common address
Default address. Projector will always execute the command coming from a RCU programmed with that common address.
Component Video
In Component Video the term component describes a number (3) of elements that are needed to make up the video picture, these
components are R-Y/Y/B-Y. A composite video signal on the other hand contains all the information needed for the color picture in
a single channel of information
DVI
Digital Visual Interface is a display interface developed in response to the proliferation of digital flat panel displays.
The digital video connectivity standard that was developed by DDWG (Digital Display Work Group). This connection standard offers
two different connectors: one with 24 pins that handles digital video signals only, and one with 29 pins that handles both digital
and analog video. This standard uses TMDS (Transition Minimized Differential Signal) from Silicon Image and DDC (Display Data
Channel) from VESA (Video Electronics Standards Association).
DVI can be single or dual link.
Graphics
Native resolution of the LCD panels = 1024 pixels x 768 pixels (4:3)
GUI
Graphic User Interface
IP
Internet Protocol. The network layer of TCP/IP. Required for communication with the internet.
LAN
Local Area Network
PiP
PiP stands for "Picture in Picture" and allows to display multiple windows containing each of them an image. The windows may be
of the video or data type.
Projector address
Address installed in the projector to be individually controlled.
Reality(SXGA)
Native resolution of the LCD panels = 1366 pixels x 1024 pixels (4:3)
Reality(SXGA+)
Native resolution of the LCD panels = 1400 x 1050 pixels (4:3)
SBC
Single Board Computer,
R5976491 IQ PRO G500 01/02/2007
183
Glossary
Video Selector
The Video Selector is a graphical interface which allows an overview of the different video inputs (Composite Video and S-Video)
and whether they are active (signal connected) or not as well as the selection of these different signals.
WAN
Wide Area Network
184
R5976491 IQ PRO G500 01/02/2007
Index
INDEX
A
Address 37–38, 114
Program 38
RCU 38
Projector address 114
setting 37
Adjustments 113
lens 113
AGC 72
Auto Image 96
AutoImage 110
Setup 110
B
Background 86
Battery 17
Installation 17
blanking 67
Blanking 111
C
Cleaning 17, 175
dustfilters 175
Lens 17
configuration 132
server 132
Connections 19–20, 24–25
Communication 24
Communications 25
RS232 IN 25
input source connections 19
Input source connections 19–20
facilities 20
layers 19
power connection 19
Control 137
description 137
D
diagnostics 147
description 147
Diagnostics 82
Digital 23
DVI 23
Digital Zoom 39
Dimensions 6
projector 6
display 105
setup 105
dropzone 151, 153
dropping 153
tools 151
E
exchange 163–164, 167
example 167
installation 163
troubleschooting 164
Exchange 165
exchange integration 169
folder form 169
Extended configuration 25
F
FAQ 173
File 95, 97, 100–102
R5976491 IQ PRO G500 01/02/2007
copy 101
delete 102
edit 97
load 95
rename 100
Filters 175
cleaning 175
location 175
firmware 149
upgrade 149
Full screen representation
105
G
Gain 72–73
automatic control 72
manual control 73
Gemini 122
General 50–53
audio 51
Audio 51–52
settings 52
setup 51
identification 53
Standby Timer 50
General menu 49
freeze 49
pause 49
General settings 49
General Menu 49
Getting started 29, 33, 35, 37, 39–40
address 37
Controlling the projector 39
digital zoom 39
lamp runtime 33
quick set up 35
Quick Set up 35
lens 35
using the dialogboxes 40
using the menu 39
guidelines 161
general network config 161
Network 161
I
Identification screen 53
Image 62
resolution 62
image files 103
forced file load 103
Image files 177
standard 177
Image settings 55
Image menu 55
Input 21–24, 67
input balance 67
Input source connection 21–24
5-Cable input 21
Composite Video input 22
computer input 24
DVI 23
S-Video input 23
Input source connections 25–27
Extended configuration 25–27
5–cable 25
introduction 25
S-Video 26
summarizing 27
installation 163
procedure 163
Installation 9, 122
185
Index
Gemini 122
guidelines 9
Installation guidelines 9–10, 14
configurations 10
guidelines 9
lenses 14
Safety 9
safety warnings 9
L
lamp 34
error 34
Lamp 33
runtime 33
Lamp history 90
Lamp mode 87
Language 116
Layers 19
input 19
Lens 6, 16–17, 35, 113
Cleaning 17
lens adjustments 113
Packaging 6
unpack 6
quick Adjustment 35
removing 16
Lenses 14–15
available lenses 14
formulas 15
installation 15
Local keypad 29
textbox 106
Lamp menu 87, 90–92
history 90
Mode 87
reset runtime 91
Runtime warning 92
runtimes 87
Signal menu 85–86
background 86
switching mode 85
Source selection 43
structure 39
Tools 75
PiP 75
Tools menu 75, 77–82
Diagnostics 82
PiP add window 77
PiP Adjust 81
PiP delete layout 80
PiP layout 79
PiP remove window 78
PiP rename layout 80
PiP Save 79
PiP select 77
using the menu 39
menu bar 108
N
Native resolution 62
network 127, 129, 138–139, 144, 151, 155, 158–159, 161
additional config info 161
configuration 129
control 138–139, 144
advanced 144
M
general 138
Menu 39, 43, 55–58, 63–65, 67, 72–73, 75, 77–82, 85–87, 90–92,
interface 138
95, 97, 100–102, 105–106, 109–110, 113–118, 121
source selection 139
Image files menu 95, 97, 100–102
dropzone 151, 155
copy file 101
remote desktop sharing 155
delete file 102
Dropzone 155
edit file 97
file manager 155
load file 95
DropZone 151, 158
rename file 100
settings 158
Image menu 55–58, 63–65, 67, 72–73
start up 151
AGC on video 72
Server 127
aspect ratio 58
start up 127
Brightness 56
web 159
color 56
Network 123–127, 137, 139, 142, 145, 147–148
color temperature 64
architecture 123
contrast 56
configuration 148
filmmode detection 65
E-mail 148
Gamma 57
Connections 126
input balance 67
control 145
Keystone 63
advanced lens adjustments 145
manual gain control 73
advanced options 145
noise reduction 58
Control manager 139, 142
phase 58
image settings 142
settings 55
PiP 139
sharpness 57
diagnostics manager 147
Tint 57
functionality 124
installation menu 113
Getting started 125
Installation menu 105–106, 109–110, 113–118, 121
installing 127
AutoImage Setup 110
software 127
Automatic startup 118
Projector 137
change password 121
control 137
Full screen representation 105
No signal 86
language 116
background 86
lens adjustments 113
projector address 114
projector orientation 115
Quick access keys 117
RS232 baudrate 118
Sliderbox position 109
Startup screen 105
Take screenshot 106
186
O
Orientation 115
projector orientation 115
oulook integration 170
limitations 170
R5976491 IQ PRO G500 01/02/2007
Index
outlook intagration
167
P
Packaging 5–6
Lens 6
projector 5
parameter 165
list 165
Password 121
change password 121
PiP 77–81
add window 77
adjust 81
layout 79
Layout 79–80
delete 80
rename 80
save 79
remove window 78
select 77
Power mode 89
Projector 5–6, 32, 38
Controlling 38
dimensions 5–6
packaging 5
Packaging 5
unpack 5
Switch on 32
Q
Quick access keys
117
R
RCU 17, 29, 31, 35
Battery 17
Terminology 31
Overview 31
Using 35
Removing 16
lens 16
RS232 baudrate 118
Runtime 91–92
R5976491 IQ PRO G500 01/02/2007
reset 91
warning 92
S
Screenshot 106
security 119
shipped Box 5
content 5
Sliderbox position 109
SNMP 171
installation 171
integration 171
Source 43, 85
selection 43
Source selection 43
switching mode 85
source files 177
standard 177
Source selection 44–46
composite video 44
S-Video 45
video selector 46
specifications 125
Startup 118
automatic 118
Startup screen 105
status bar 108
Switching 85
switching mode 85
T
Textbox 106
Timer 50
troubleshooting
173
V
Video 22–23, 72–73
AGC 72
Composite Video 22
manual gain control 73
S-Video 23
187
Index
188
R5976491 IQ PRO G500 01/02/2007
Revision Sheet
To:
Barco nv Presentations
Noordlaan 5, 8520 Kuurne
Phone: +32 56.36.82.11, Fax: +32 56.35.86.51
E-mail: presentations.bid@barco.com, Web: www.barco.com
From:
Date:
Please correct the following points in this documentation (R5976491/09):
page
R5976491
wrong
IQ
PRO G500
01/02/2007
correct
Download PDF

advertising