Specifications | Barco R9010510 Projector User Manual

INSTALLATION INSTRUCTIONS
WALL MOUNTED
PACKAGE HEAT PUMPS
Models:
CH3S1
CH4S1
CH5S1
NOTE
THIS IS AN R-410A
HIGH PRESSURE
REFRIGERANT SYSTEM
Bard Manufacturing Company, Inc.
Bryan, Ohio 43506
Since 1914...Moving ahead just as planned.
© Copyright 2004
Manual :
Supersedes:
File:
Date:
2100-455A
2100-455
Volume III Tab 17
08-18-06
Manual
Page
2100-455A
1 of 25
CONTENTS
Getting Other Information and Publications
For More Information ............................................... 3
Wall Mount General
Heat Pump Wall Mount Model Nomenclature ....... 4
Shipping Damage ................................................. 8
General .............................................................. 8
Duct Work ............................................................. 8
Filters
.............................................................. 8
Condensate Drain – Evaporator ........................... 8
Installation Instructions
Wall Mounting Information .................................... 9
Mounting the Unit .................................................. 9
Wiring – Main Power ........................................... 15
Wiring – Low Voltage Wiring ............................... 15
Low Voltage Connections ................................... 16
Figures
Figure 1
Figure 2
Figure 3
Figure 4
Figure 5
Figure 6
Figure 7
Figure 8
Figure 9
Figure 10
Figure 11
Figure 12
Figure 13
Unit Dimensions CH3S1 ...................... 5
Unit Dimensions CH4S1 & CH5S1 ...... 6
Mounting Instructions CH3S1 ............ 10
Mounting Instructions CH4S1/CH5S1 . 11
Electric Heat Clearance ..................... 12
Wall Mounting Instructions ................. 13
Wall Mounting Instructions ................. 13
Common Wall Mounting Installations . 14
Common Wall Mounting Installations . 15
Unit 24V Terminal Board .................... 15
Low Pressure Control Bypass Timer . 17
Defrost Control Board ........................ 19
Fan Blade Setting .............................. 22
Manual 2100-455A
Page
2 of 25
Start Up
Application .......................................................... 16
Safety Practices .................................................. 17
Important Installer Note ....................................... 17
Pressure Service Ports ....................................... 17
High & Low Pressure Switch .............................. 17
Three Phase Scroll Compressor Start Up ... 17 & 18
Phase Monitor ..................................................... 18
Service Hints ....................................................... 18
Sequence of Operation ....................................... 18
Compressor Current & Pressure
Control Module ................................................... 18
Defrost Cycle ...................................................... 19
Troubleshooting
Solid State Heat Pump Control
Troubleshooting Procedure ................................. 20
Checking Temperature Sensor
Outside Unit Circuit ............................................. 21
Temperature vs. Resistance of Temperature ...... 21
Compressor Solenoid ......................................... 22
Fan Blade Setting Dimensions ........................... 22
Removal of Fan Shroud ...................................... 22
Refrigerant Charge R-410A ................................ 22
Pressure Tables ............................................. 24-25
Tables
Table 1
Table 2
Table 3
Table 4
Table 5
Table 6
Table 7
Table 8
Table 9
Table 10
Table 11
Table 12
Table 13
Electric Heat Table ................................ 4
Electrical Specifications ........................ 7
Thermostat Wire Size ......................... 15
Wall Thermostat .................................. 16
Troubleshooting .................................. 20
Fan Blade Dimensions ........................ 22
Refrigerant Charge ............................. 23
Indoor Blower Performance ................ 23
Maximum ESP of Operation ............... 23
Pressure Table - High Cooling ............ 24
Pressure Table - Low Cooling ............. 24
Pressure Table - High Heating ............ 25
Pressure Table - Low Heating ............. 25
Getting Other Information and Publications
These publications can help you install the air
conditioner or heat pump. You can usually find these at
your local library or purchase them directly from the
publisher. Be sure to consult current edition of each
standard.
FOR MORE INFORMATION, CONTACT
THESE PUBLISHERS:
ACCA
Air Conditioning Contractors of America
1712 New Hampshire Ave. N.W.
Washington, DC 20009
Telephone: (202) 483-9370
Fax: (202) 234-4721
ANSI
American National Standards Institute
11 West Street, 13th Floor
New York, NY 10036
Telephone: (212) 642-4900
Fax: (212) 302-1286
National Electrical Code ...................... ANSI/NFPA 70
Standard for the Installation .............. ANSI/NFPA 90A
of Air Conditioning and Ventilating Systems
Standard for Warm Air ...................... ANSI/NFPA 90B
Heating and Air Conditioning Systems
Load Calculation for ............................ ACCA Manual J
Residential Winter and Summer Air Conditioning
Duct Design for Residential .............. ACCA Manual D
Winter and Summer Air Conditioning and Equipment
Selection
ASHRAE American Society of Heating, Refrigerating,
and Air Conditioning Engineers, Inc.
1791 Tullie Circle, N.E.
Atlanta, GA 30329-2305
Telephone: (404) 636-8400
Fax: (404) 321-5478
NFPA
National Fire Protection Association
Batterymarch Park
P.O. Box 9101
Quincy, MA 02269-9901
Telephone: (800) 344-3555
Fax: (617) 984-7057
Manual 2100-455A
Page
3 of 25
WALL MOUNT GENERAL INFORMATION
HEAT PUMP WALL MOUNT MODEL NOMENCLATURE
CH
4S
1
–
A
05
B
P
X
X
X
X
MODEL NUMBER
CONTROL MODULES
KW
COIL OPTIONS
X - Standard
CAPACITY
REVISIONS
3S - 3 ton
4S - 4 ton
5S - 5 ton VOLTS & PHASE
A - 230/208/60/1
B - 230/208/60/3
C - 460/60/3
OUTLET OPTIONS
X - Front (Standard)
T - Top Outlet
VENTILATION OPTIONS
B - Blank-off Plate
R - Energy Recovery
V - Commercial Ventilator Motorized with Exhaust
COLOR OPTIONS
X - Beige (Standard)
4 - Buckeye Gray
5 - Desert Brown
8 - Dark Bronze
FILTER OPTIONS
P - 2-Inch Pleated
TABLE 1
ELECTRIC HEAT TABLE
CH3S1-A
Models
240-1
KW
A
B TU
CH3S1-B
208-1
A
B TU
240-3
A
B TU
208-3
A
B TU
460-3
A
B TU
4
5
CH4S1-A
CH5S1-A
CH3S1-C
240-1
A
B TU
CH4S1-B
CH5S1-B
208-1
A
B TU
240-3
A
B TU
CH4S1-C
CH5S1-C
208-3
A
B TU
460-3
A
B TU
7.2
20480
16.7 13650 14.4 10240
20.8 17065 18.1 12800
20.8 17065 18.1 12800
6
14.4 20500 12.5 15360
9
21.7 30600 18.7 23030 10.8 30700
7.2
20480
14.4 20500 12.5 15360
21.7 30600 18.7 23030 10.8 30700
10
41.6 34130 36.2 25600
15
62.5 51200 54.1 38400 36.2 51200 31.2 38400 18.0 51200 62.5 51200 54.1 38400 36.2 51200 31.2 38400 18.0 51200
41.6 34130 36.2 25600
18
20
Manual 2100-455A
Page
4 of 25
43.3 61400 37.5 46050 21.6 61400
83.2 68250 72.1 51200
Manual 2100-455A
Page
5 of 25
Left Side View
Cond.
Outlet
Grille
Slope Top
Evap. Drain
Hose
Vent Option
Access Door
Filter Access
Door
Blower Access
Door
1 3/8"
Heater Access
Door
31 5/8"
13 3/8"
High Voltage
Entrance
Low Voltage
Entrance
C. Breaker
Access Door
Control Panel
Door
84 11/16"
6 7/8"
5 13/16"
Drain for optional
drain pan
Front View
Cond.
Inlet
Grille
42 3/16"
43 7/8"
Top View
Optional Top Outlet
39 7/8"
31""
16"
Access Door
32 3/4"
16"
16"
16"
16"
7/8"
6 9/16"
Back View
Return
Opening
Supply
Opening
29 7/8"
43"
"CH3S1" Unit Dimensions
Right Side View
Cond.
Outlet
Grille
FIGURE 1
UNIT DIMENSIONS
MIS-2146
Opt. High Voltage
Entrances
(12) Wall
Mounting Holes
8 9/16"
2 1/4"
48 1/16"
Top Rain
Flashing
15 7/8"
6 1/8"
9 13/16"
Manual 2100-455A
Page
6 of 25
Left Side View
Cond.
Outlet
Grille
Slope Top
Evap. Drain
Hose
Vent Option
Access Door
Filter Access
Door
Blower Access
Door
1 3/8"
Front View
Heater Access
Door
41 5/8"
13 3/8"
Access Door
High Voltage
Entrance
Low Voltage
Entrance
C. Breaker
Access Door
Control Panel
Door
94 11/16"
6 7/8"
5 13/16"
Drain for optional
drain pan
Condenser
Inlet Grille
43 7/8"
42 3/16"
Top View
Optional Top Outlet
39 7/8"
Right Side View
22 3/16"
Cond.
Outlet
Grille
31"
(12) Wall
Mounting
Holes
42 3/4"
16"
16"
16"
16"
16"
7/8"
6 9/16"
Back View
Return
Opening
Supply
Opening
29 7/8"
43"
MIS-2020 A
Opt. High
Voltage
Entrances
2 1/4"
48 1/16"
Top Rain
Flashing
15 7/8"
6 1/8"
9 13/16"
8 9/16"
"CH4S1 and CH5S1" Unit Dimensions
FIGURE 2
UNIT DIMENSIONS
TABLE 2
ELECTRICAL SPECIFICATIONS
SINGLE CIRCUIT
DUAL CIRCUIT
1
N o.
3
1
2
2
3
2
2
Maximum
Field Minimum Maximum Field Ground Minimum Circuit
Field Pow er
Ground
External Fuse
Pow er Circuit
External Pow er Wire
Ampacity
Wire Siz e
Wire Siz e
or Circuit
Ciruits Ampacity Fuse or
Wire
Siz e
Breaker
Circuit
Siz e
Breaker
Ckt. Ckt. Ckt. Ckt. Ckt. Ckt. Ckt. Ckt. Ckt. Ckt. Ckt. Ckt.
A
B
C
A
B
C
A
B
C
A
B
C
Model
Rated
Volts &
P h ase
CH3S1-A0Z
A 05
A 10
A 15
230/208-1
230/208-1
230/208-1
230/208-1
1
1
1 or 2
1 or 2
29
55
81
85
45
60
90
90
8
6
4
4
10
10
8
8
----29
33
----52
52
---------
----45
45
----60
60
---------
----10
8
----6
6
---------
----10
10
----10
10
---------
CH3S1-B0Z
B 06
B 09
B 15
230/208-3
230/208-3
230/208-3
230/208-3
1
1
1
1
23
41
50
50
30
45
50
50
10
8
8
8
10
10
10
10
---------
---------
---------
---------
---------
---------
---------
---------
---------
---------
---------
---------
CH3S1-C0Z
C 06
C 09
C 15
460-3
460-3
460-3
460-3
1
1
1
1
11
20
24
24
15
20
25
25
14
12
10
10
14
12
10
10
---------
---------
---------
---------
---------
---------
---------
---------
---------
---------
---------
---------
CH4S1-A0Z
A 04
A 05
A 10
A 15
A 20
230/208-1
230/208-1
230/208-1
230/208-1
230/208-1
230/208-1
1
1
1 or 2
1 or 2
1 or 2
1 or 3
37
57
63
89
89
113
50
60
70
90
90
120
8
6
6
3
3
2
10
10
8
8
8
6
----37
37
37
52
----26
52
52
52
----------26
----50
50
50
50
----30
60
60
60
----------30
----8
8
8
6
----10
6
6
6
----------10
----10
10
10
10
----10
10
10
10
----------10
CH4S1-B0Z
B 06
B 09
B 15
B 18
230/208-3
230/208-3
230/208-3
230/208-3
230/208-3
1
1
1
1
1
27
45
54
54
55
35
50
60
60
60
8
8
6
6
6
10
10
10
10
10
-----------
-----------
-----------
-----------
-----------
-----------
-----------
-----------
-----------
-----------
-----------
-----------
CH4S1-C0Z
C 06
C 09
C 15
C 18
460-3
460-3
460-3
460-3
460-3
1
1
1
1
1
14
23
28
28
28
20
25
30
30
30
12
10
10
10
10
12
10
10
10
10
-----------
-----------
-----------
-----------
-----------
-----------
-----------
-----------
-----------
-----------
-----------
-----------
CH5S1-A0Z
A 04
A 05
A 10
A 15
A 20
230/208-1
230/208-1
230/208-1
230/208-1
230/208-1
230/208-1
1
1 or 2
1 or 2
1 or 2
1 or 2
1 or 3
44
65
70
96
96
114
60
70
80
100
100
120
6
4
4
3
3
2
10
8
8
8
8
6
--44
44
44
44
44
--21
26
52
52
52
----------26
--60
60
60
60
60
--25
30
60
60
60
----------30
--8
8
8
8
8
--10
10
6
6
6
----------10
--10
10
10
10
10
--10
10
10
10
10
----------10
CH5S1-B0Z
B 06
B 09
B 15
B 18
230/208-3
230/208-3
230/208-3
230/208-3
230/208-3
1
1
2
2
2
36
54
63
63
64
50
60
70
70
70
8
6
4
4
4
10
10
6
6
6
----36
36
37
----28
28
28
-----------
----50
50
50
----30
30
30
-----------
----8
8
8
----10
10
10
-----------
----10
10
10
----10
10
10
-----------
CH5S1-C0Z
C 06
C 09
C 15
C 18
460-3
460-3
460-3
460-3
460-3
1
1
1
1
1
19
28
32
32
33
25
35
35
35
35
10
8
8
8
8
10
10
10
10
10
-----------
-----------
-----------
-----------
-----------
-----------
-----------
-----------
-----------
-----------
-----------
-----------
1 Maximum size of the time delay fuse or HACR type circuit breaker for protection of field wiring conductors.
2 Based on 75°C copper wire. All wiring must conform to NEC and all local codes.
3 These “Minimum Circuit Ampacity” values are to be used for sizing the field power conductors. Refer to the National Electric Code
(latest revision), Article 310 for power conductor sizing.
CAUTION: When more than one field power conductor circuit is run through one conduit, the conductors must be derated. Pay special
attention to note 8 of table 310 regarding Ampacity Adjustment Factors when more than 3 conductors are in a raceway.
Manual 2100-455A
Page
7 of 25
SHIPPING DAMAGE
Upon receipt of equipment, the carton should be
checked for external signs of shipping damage. If
damage is found, the receiving party must contact the
last carrier immediately, preferably in writing,
requesting inspection by the carrier’s agent.
GENERAL
The equipment covered in this manual is to be installed
by trained, experienced service and installation
technicians.
Design the duct work according to methods given by the
Air Conditioning Contractors of America (ACCA).
When duct runs through unheated spaces, it should be
insulated with a minimum of one inch of insulation.
Use insulation with a vapor barrier on the outside of the
insulation. Flexible joints should be used to connect the
duct work to the equipment in order to keep the noise
transmission to a minimum.
These units are suitable for 0 inch clearance to
combustible material. See Wall Mounting Instructions
and Figures 3, 4, 5, 6 & 7 for further details.
The refrigerant system is completely assembled and
charged. All internal wiring is complete.
Ducts through the walls must be insulated and all joints
taped or sealed to prevent air or moisture entering the
wall cavity.
The unit is designed for use with or without duct work.
Flanges are provided for attaching the supply and return
ducts.
Some installations may not require any return air duct.
A metallic return air grille is required with installations
not requiring a return air duct. The spacing between
louvers on the grille shall not be larger than 5/8 inch.
These instructions explain the recommended method to
install the air cooled self-contained unit and the
electrical wiring connections to the unit.
NOTE: If no return air duct is used, applicable
installation codes may limit this cabinet to
installation only in a single story structure.
These instructions and any instructions packaged with
any separate equipment, required to make up the entire
air conditioning system should be carefully read before
beginning the installation. Note particularly “Starting
Procedure” and any tags and/or labels attached to the
equipment.
Any grille that meets with 5/8 inch louver criteria may
be used. It is recommended that Bard Return Air Grille
Kit RG2 through RG5 or RFG2 through RFG5 be
installed when no return duct is used. Contact
distributor or factory for ordering information. If using
a return air filter grille, filters must be of sufficient size
to allow a maximum velocity of 400 fpm.
While these instructions are intended as a general
recommended guide, they do not supersede any national
and/or local codes in any way. Authorities having
jurisdiction should be consulted before the installation is
made. See Page 3 for information on codes and
standards.
Size of unit for a proposed installation should be based
on heat loss calculation made according to methods of
Air Conditioning Contractors of America (ACCA). The
air duct should be installed in accordance with the
Standards of the National Fire Protection Association
for the Installation of Air Conditioning and Ventilating
Systems of Other Than Residence Type, NFPA No.
90A, and Residence Type Warm Air Heating and Air
Conditioning Systems, NFPA No. 90B. Where local
regulations are at a variance with instructions, installer
should adhere to local codes.
DUCT WORK
Any heat pump is more critical of proper operating
charge and an adequate duct system than a straight air
conditioning unit. All duct work, supply and return,
must be properly sized for the design airflow
requirement of the equipment. Air Conditioning
Contractors of America (ACCA) is an excellent guide to
proper sizing. All duct work or portions thereof not in
the conditioned space should be properly insulated in
order to both conserve energy and prevent condensation
or moisture damage.
Manual 2100-455A
Page
8 of 25
FILTERS
A 2-inch pleated filter is supplied with each unit. The
filter slides into position making it easy to service. This
filter can be serviced from the outside by removing the
filter access door.
CONDENSATE DRAIN – EVAPORATOR
A plastic drain hose extends from the drain pan at the
top of the unit down to the unit base. There are
openings in the unit base for the drain hose to pass
through. In the event the drain hose is connected to a
drain system of some type, it must be an open or vented
type system to assure proper drainage.
INSTALLATION INSTRUCTIONS
WALL MOUNTING INFORMATION
1. Two holes for the supply and return air openings
must be cut through the wall as shown in Figure 3.
3. Locate and mark lag bolt locations and bottom
mounting bracket location. See Figure 3.
4. Mount bottom mounting bracket.
2. On wood frame walls, the wall construction must be
strong and rigid enough to carry the weight of the
unit without transmitting any unit vibration.
5. Hook top rain flashing under back bend of top. Top
rain flashing is shipped with unit attached to back of
unit on the right side.
3. Concrete block walls must be thoroughly inspected
to insure that they are capable of carrying the weight
of the installed unit.
6. Position unit in opening and secure with 5/16 lag
bolts; use 3/4 inch diameter flat washers on the lag
bolts.
MOUNTING THE UNIT
1. These units are secured by wall mounting brackets
which secure the unit to the outside wall surface at
both sides. A bottom mounting bracket is provided
for ease of installation, but is not required.
2. The unit itself is suitable for 0 inch clearance. If a
combustible wall use a minimum of 30" x 10"
dimensions for sizing. However, it is generally
recommended that a 1-inch clearance is used for
ease of installation. The supply air opening would
then be 32" x 12". See Figures 3 and 4 for details.
7. Secure rain flashing to wall and caulk across entire
length of top. See Figure 3.
8. For additional mounting rigidity, the return air and
supply air frames or collars can be drilled and
screwed or welded to the structural wall itself
(depending upon wall construction). Be sure to
observe required clearance if combustible wall.
9. On side-by-side installations, maintain a minimum
of 20 inches clearance on right side to allow access
to control panel and heat strips, and to allow proper
airflow to the outdoor coil. Additional clearance
may be required to meet local or national codes.
Manual 2100-455A
Page
9 of 25
18"
3
D
12
32
5
16"
16"
16"
16"
16"
68"
C
5 1/2
6 1/2
C
16"
30"
Return Opening
Supply Opening
A
43"
10
30
B
16"
16"
16"
16"
C
REQUIRED DIM. TO MAINTAIN 0"
MIN. CLEARANCE FROM
COMBUSTIBLE MATERIALS
REQUIRED DIM. TO MAINTAIN
OPTIONAL 1" CLEARANCE FROM
COMBUSTIBLE MATERIALS
A
"CH3S1" Wall Mounting Instructions
2
1
D
5
6
E
16"
E
B
Heater
Access
Panel
Wall
Bottom Wall Bracket
(Install before unit)
Unit Mounting
Holes, 12 places
D
FIGURE 3
MOUNTING INSTRUCTIONS
Optional
Top Outlet
68"
7
Top
Apply a bead of caulk
along entire length of top
and behind side mounting
flanges
Rain Flashing (supplied)
3
18"
Return Air
Opening
Supply Duct
Wall Section
Manual 2100-455A
Page
10 of 25
MIS-2209
0" min.
0" min.
Foam
Manual 2100-455A
Page
11 of 25
'
&
5HWXUQ2SHQLQJ
6XSSO\2SHQLQJ
$
&
(
%
%RWWRP:DOO%UDFNHW
,QVWDOOEHIRUHXQLW
:DOO
5DLQ)ODVKLQJVXSSOLHG
2SWLRQDO
7RS2XWOHW
7RS
$SSO\DEHDGRIFDXON
DORQJHQWLUHOHQJWKRIWRS
DQGEHKLQGVLGHPRXQWLQJ
IODQJHV
+HDWHU
$FFHVV
3DQHO
8QLW0RXQWLQJ
+ROHVSODFHV
'
&+6DQG&+6:DOO0RXQWLQJ,QVWUXFWLRQV
FIGURE 4
MOUNTING INSTRUCTIONS
5HWXUQ$LU
2SHQLQJ
)RDP
PLQ
0,6$
PLQ
6XSSO\'XFW
:DOO6HFWLRQ
FIGURE 5
ELECTRIC HEAT CLEARANCE
Typical Building
Outside Sheeting
Wall Frame
Inside Sheeting
Supply Air
Duct
Unit
Supply Air Duct
Flange of Wall
1" OPTIONAL CLEARANCE
RECOMMENDED
Side section view of supply air
duct for wall mounted unit showing
0" clearance to combustible surfaces.
MIS-2210
Note: This unit is approved for 0" clearance, but the optional 1" clearance is recommended. See Figures 3 & 4.
Manual 2100-455A
Page
12 of 25
FIGURE 6
WALL MOUNTING INSTRUCTIONS
Interior finished wall
Exterior wood or
steel siding wall
Supply opening
Framing material:
2x4's, 2x6's, and/or
structural steel
Factory supplied rain
flashing. Attach to
unit before installing.
Return
opening
"CH" Unit
Bottom mounting
bracket. Mount on wall
before installing unit.
!
Follow all local building codes
when framing wall to support unit.
MIS-2024
FIGURE 7
WALL MOUNTING INSTRUCTIONS
44 7/8"
29 7/8"
Supply Opening
9 13/16"
1" clearance
6 1/8"
Return Opening
15 7/8"
1" clearance
Locate stud to match
spacing for rest of wall.
A second member may
be required for some
walls.
51 1/4"
These structural
members must be
able to support the
entire weight of the
unit.
CL
!
Follow all local building codes
when framing wall to support unit.
MIS-2025
Manual 2100-455A
Page
13 of 25
FIGURE 8
COMMON WALL MOUNTING INSTALLATIONS
Free Air Flow - No Duct
Low Sound With Acoustical Plenums
And Isolation Curbs
Free Air Flow - No Duct
Unit (outside)
Rafters
Finished Ceiling
Grille
Isolation Curb
WM1CF5-X
ir
yA
ppl
u
S
Supply Air
Free Blow
Supply Plenum
WAFB51-X
Return Air
Grille
Outside Wall
Return Air
Silencer
WAPR11-X
RETURN AIR
Ducted Supply - Return At Unit
False Wall Installation
Note: duct maybe in attic or
below rafters as shown.
Rafters
Unit (outside)
Supply Air
Note: duct maybe in attic or
below rafters as shown.
Rafters
Unit (outside)
Supply Air
Duct
Finished Ceiling
Finished Ceiling
Wall Sleeve
Return Air
False Wall
Outside Wall
Note: direction of return
grille louvers is pointed down
for lowest sound level as shown.
Return Air
Outside Wall
Duct
Return Air
Grille
MIS-2027
Manual 2100-455A
Page
14 of 25
FIGURE 9
COMMON WALL MOUNTING INSTALLATIONS
Closet Installation
Note: duct maybe in attic or
below rafters as shown.
Rafters
Unit (outside)
WIRING – LOW VOLTAGE WIRING
230 / 208V, 1 phase and 3 phase equipment dual
primary voltage transformers. All equipment leaves the
factory wired on 240V tap. For 208V operation,
reconnect from 240V to 208V tap. The acceptable
operating voltage range for the 240 and 208V taps are:
Duct
Supply Air
Finished Ceiling
TAP
240
208
Grille
Wall Sleeve
RANGE
253 – 216
220 – 187
Closet Wall
Closet Wall
Return Air
Outside Wall
NOTE: The voltage should be measured at the field
power connection point in the unit and while
the unit is operating at full load (maximum
amperage operating condition).
Raised Closet Floor
FIGURE 10
UNIT 24V TERMINAL BOARD
Grille
Return Air
T7652H1000 THERMOSTAT
BARD PART #8403-052
MIS-2240
WIRING – MAIN POWER
Refer to the unit rating plate for wire sizing information
and maximum fuse or “HACR” type circuit breaker
size. Each outdoor unit is marked with a “Minimum
Circuit Ampacity”. This means that the field wiring
used must be sized to carry that amount of current.
Depending on the installed KW of electric heat, there
may be two field power circuits required. If this is the
case, the unit serial plate will so indicate. All models
are suitable only for connection with copper wire. Each
unit and/or wiring diagram will be marked “Use Copper
Conductors Only”. These instructions must be adhered
to. Refer to the National Electrical Code (NEC) for
complete current carrying capacity data on the various
insulation grades of wiring material. All wiring must
conform to NEC and all local codes.
The electrical data lists fuse and wire sizes (75° C
copper) for all models including the most commonly
used heater sizes. Also shown are the number of field
power circuits required for the various models with
heaters.
The unit rating plate lists a “Maximum Time Delay
Relay Fuse” or “HACR” type circuit breaker that is to
be used with the equipment. The correct size must be
used for proper circuit protection and also to assure that
there will be no nuisance tripping due to the momentary
high starting current of the compressor motor.
The disconnect access door on this unit may be locked
to prevent unauthorized access to the disconnect. To
convert for the locking capability, bend the tab located
in the bottom left hand corner of the disconnect opening
under the disconnect access panel straight out. This tab
will now line up with the slot in the door. When shut, a
padlock may be placed through the hole in the tab
preventing entry.
See “Start Up” section for important information on
three phase scroll compressor start ups.
C
G
Rc Rh
Y1 Y2
B
L
W1
A1
1F93-380 THERMOSTAT
BARD PART #8403-049
C
G
R
Y1 Y2
B
W1 W2
E
C
G
R
Y
B
W1 W2 W3
E
Y1
W3/A1
L
DH O1
UNIT LOW VOLTAGE
TERMINAL BLOCK
Factory Jumper
MIS-2026 A
Nine (9) wires should be run from thermostat subbase to
the 24V terminal board in the unit. A nine conductor,
18 gauge copper color-coded thermostat cable is
recommended. The connection points are shown in
Figure 10.
IMPORTANT
Only the thermostat combinations as shown
above will work with this equipment.
TABLE 3
THERMOSTAT WIRE SIZE
Transformer
VA
55
FLA
Wire Gauge
Maximum
Distance
In Feet
2.3
20 gauge
18 gauge
16 gauge
14 guage
12 guage
45
60
100
160
250
Manual 2100-455A
Page
15 of 25
LOW VOLTAGE CONNECTIONS
These units use a grounded 24 volt AC low voltage
circuit and require at least a 2 stage heating and a 2
stage cooling thermostat.
The “R” terminal is the hot terminal and the “C”
terminal is grounded.
TABLE 4
WALL THERMOSTAT
Thermostat
Predominant Features
8403-049
(1F93-380)
2 stg. cool; 2 stg. heat
Programmable Electronic
Auto or Manual changeover
“G” terminal is the fan input.
“Y” terminal is the compressor Stage 1 input.
8403-052
“Y1” terminal is the compressor Stage 2 input.
2 stg. cool; 3 stg. heat
Programmable Electronic
Auto or Manual changeover
“B” terminal is the reversing valve input. The reversing
valve must be energized for heating mode.
START UP
“R” terminal is 24 VAC hot.
“C” terminal is 24 VAC grounded.
“L” terminal is compressor lockout output. This
terminal is activated on a high or low pressure trip by
the electronic heat pump control. This is a 24 VAC
output.
“W2” terminal is second stage heat (if equipped).
“O1” terminal is the ventilation input. This terminal
energizes any factory installed ventilation option.
“E” terminal is the emergency heat input. This terminal
energizes the emergency heat relay if equipped.
NOTE: For total and proper control using DDC, a
total of 7 controlled outputs are required (6 if
no ventilation system is installed). For proper
system operation under Emergency Heat
conditions where the compressor needs to be
deactivated, the B-W2-E outputs need to be
energized. Removing the Y (compressor) signal
alone turns the compressor off, but does not
activate the additional circuitry embedded in
the heat pump for proper and complete
operation.
LOW VOLTAGE CONNECTIONS
FOR DDC CONTROL
Fan Only
Energize G
Cooling Mode 1st Stage
Energize Y, G
Cooling Mode 2nd Stage
Energize Y, Y1, G
Heat Pump Heating 1st Stage
Energize Y, G, B
Heat Pump Heating 2nd Stage Energize Y, Y1, G, B
3rd Stage Heating
w/Heat Pump (if employed)
Energize G, W2, Y, B, Y1
Ventilation
Energize G, O1
Emergency Heat
Energize B, W2, E, G
Manual 2100-455A
Page
16 of 25
These units require R-410A refrigerant & Polyol Ester oil.
APPLICATION:
1. Use separate service and manufacturing equipment
to avoid cross contamination of oil and refrigerants.
2. Use recovery equipment rated for R-410A
refrigerant.
3. Use manifold gauges rated for R-410A (800 psi/250
psi low).
4. R-410A is a binary blend of HFC-32 and HFC-125.
5. R-410A is nearly azeotropic - similar to R-22 and
R-12. Although nearly azeotropic, charge with
liquid refrigerant.
6. R-410A operates at 40-70% higher pressure than
R-22, and systems designed for R-22 cannot
withstand this higher pressure.
7. R-410A has an ozone depletion potential of zero,
but must be reclaimed due to its global warming
potential.
8. R-410A compressors use Polyol Ester oil.
9. Polyol Ester oil is hygroscopic; it will rapidly
absorb moisture and strongly hold this moisture in
the oil.
10. A liquid line dryer must be used - even a deep
vacuum will not separate moisture from the oil.
11. Limit atmospheric exposure to 15 minutes MAXIMUM.
12. If compressor removal is necessary, always plug
compressor immediately after removal. Purge with
small amount of nitrogen when inserting plugs.
START UP CONT’D.
SAFETY PRACTICES:
The bypass timer should be set to 200 seconds, and this
is to assure there is no nuisance tripping of the lowpressure control during startup in heating mode under
cold weather conditions. See Figure 10:
1. Never mix R-410A with other refrigerants.
2. Use gloves and safety glasses, Polyol Ester oils can
be irritating to the skin, and liquid refrigerant will
freeze the skin.
FIGURE 11
LOW PRESSURE CONTROL BYPASS TIMER
3. Never use air and R-410A to leak check; the
mixture may become flammable.
4. Do not inhale R-410A – the vapor attacks the
nervous system, creating dizziness, loss of
coordination and slurred speech. Cardiac
irregularities, unconsciousness and ultimate death
can result from breathing this concentration.
5. Do not burn R-410A. This decomposition produces
hazardous vapors. Evacuate the area if exposed.
6. Use only cylinders rated DOT4BA/4BW 400.
7. Never fill cylinders over 80% of total capacity.
8. Store cylinders in a cool area, out of direct sunlight.
9. Never heat cylinders above 125°F.
10. Never trap liquid R-410A in manifold sets, gauge
lines or cylinders. R-410A expands significantly at
warmer temperatures. Once a cylinder or line is full
of liquid, any further rise in temperature will cause
it to burst.
IMPORTANT INSTALLER NOTE
For improved start-up performance, wash the indoor coil
with a dish washing detergent.
PRESSURE SERVICE PORTS
R-410A requires high pressure hose connections and
gauges. High and Low pressure service ports are
installed on all units so that the system operating
pressures can be observed. Pressure tables can be found
later in the manual covering all models on both cooling
and heating cycles. It is imperative to match the correct
pressure table to the unit by model number.
HIGH & LOW PRESSURE SWITCH
All models are supplied with a remote reset high and low
pressure switch. If tripped, this pressure switch may be
reset by turning the thermostat off then back on again.
High/Low Pressure control provides protection for the
compressor. In the event system pressures go above 540
PSI or below 35 PSI, in either cooling or heating mode,
the compressor will be stopped. This will activate the
“L” terminal of the low voltage terminal strip. This
terminal can be used for remote indication of a pressure
lockout. The lockout circuit will hold compressor off
line. When the system problem is corrected, the unit
operation can be restored by turning the main power
supply off and then back on, or reset the room thermostat.
The low pressure control has a bypass to eliminate
nuisance lockout on cold start up.
THREE PHASE SCROLL COMPRESSOR
START UP INFORMATION
Scroll compressors, like several other types of
compressors, will only compress in one rotational
direction. Direction of rotation is not an issue with
single phase compressors since they will always start
and run in the proper direction.
However, three phase compressors will rotate in either
direction depending upon phasing of the power. Since
there is a 50-50 chance of connecting power in such a
way as to cause rotation in the reverse direction,
verification of proper rotation must be made. All three
phase units incorporate a phase monitor to ensure proper
field wiring. See the “Phase Monitor” section later in
this manual.
Verification of proper rotation must be made any time a
compressor is changed or rewired. If improper rotation
is corrected at this time there will be no negative impact
on the durability of the compressor. However, reverse
operation for over one hour may have a negative impact
on the bearing due to oil pump out.
NOTE: If compressor is allowed to run in reverse
rotation for several minutes, the compressor’s
internal protector will trip.
All three phase ZR3 compressors are wired identically
internally. As a result, once the correct phasing is
determined for a specific system or installation,
connecting properly phased power leads to the same
Fusite terminal should maintain proper rotation
direction.
Manual 2100-455A
Page
17 of 25
Verification of proper rotation direction is made by
observing that suction pressure drops and discharge
pressure rises when the compressor is energized. Reverse
rotation also results in an elevated sound level over that
with correct rotations, as well as, substantially reduced
current draw compared to tabulate values.
The direction of rotation of the compressor may be
changed by reversing any two line connections to the unit.
PHASE MONITOR
All units with three phase compressors are equipped with
a 3 phase line monitor to prevent compressor damage due
to phase reversal.
The phase monitor in this unit is equipped with two
LEDs. If the Y signal is present at the phase monitor and
phases are correct, the green LED will light. If phases are
reversed, the red fault LED will be lit and compressor
operation is inhibited.
If a fault condition occurs, reverse two of the supply leads
to the unit. Do not reverse any of the unit factory wires
as damage may occur.
SERVICE HINTS
1. Caution homeowner to maintain clean air filters at all
times. Also, not to needlessly close off supply and
return air registers. This reduces airflow through the
system, which shortens equipment service life as well
as increasing operating costs.
2. Switching to heating cycle at 75° F or higher outside
temperature may cause a nuisance trip of the remote
reset high pressure switch. Turn thermostat off then
on to reset the high pressure switch.
3. The heat pump wall thermostats perform multiple
functions. Be sure that all function switches are
correctly set for the desired operating mode before
trying to diagnose any reported service problems.
4. Check all power fuses or circuit breakers to be sure
they are the correct rating.
5. Periodic cleaning of the outdoor coil to permit full
and unrestricted airflow circulation is essential.
SEQUENCE OF OPERATION
COOLING STAGE 1 – Circuit R-Y makes at thermostat
pulling in compressor contactor, starting the compressor
and outdoor motor. The G (indoor motor) circuit is
automatically completed on any call for cooling operation
or can be energized by manual fan switch on subbase of
constant air circulation.
COOLING STAGE 2 – Circuit R-Y1 makes at the
thermostat energizing the 2nd stage solenoid in the
compressor. Default position is not energized.
Compressor will run at low capacity until this solenoid is
energized.
Manual 2100-455A
Page
18 of 25
HEATING STAGE 1 – A 24V solenoid coil on reversing
valve controls heating cycle operation. Two thermostat
options, one allowing “Auto” changeover from cycle to
cycle and the other constantly energizing solenoid coil
during heating season and thus eliminating pressure
equalization noise except during defrost, are to be used.
On “Auto” option a circuit is completed from R-W1 and
R-Y on each heating “on” cycle, energizing reversing
valve solenoid and pulling in compressor contactor
starting compressor and outdoor motor. R-G also make
starting indoor blower motor. Heat pump heating cycle
now in operation. The second option has no “Auto”
changeover position, but instead energizes the reversing
valve solenoid constantly whenever the system switch on
subbase is placed in “Heat” position, the “B” terminal
being constantly energized from R. A thermostat demand
for Stage 1 heat completes R-Y circuit, pulling in
compressor contactor starting compressor and outdoor
motor. R-G also make starting indoor blower motor.
HEATING STAGE 2 – Circuit R-Y2 makes at the
thermostat energizing the 2nd stage solenoid in the
compressor.
COMPRESSOR CURRENT & PRESSURE
CONTROL MODULE
The compressor control module monitors compressor
current and pressure and prevents internal overload trips
due to low voltage or extremely high ambient
temperatures by de-energizing the full capacity
compressor solenoid. The control monitors current to the
compressor and discharge pressure. If current is sensed
that is in excess of 93% of the compressor, maximum
continuous current rating or pressure is sensed greater
than 525 PSI, the compressor control module deenergizes for a time as determined by the time
potentiometer on the compressor control module. This
will drop the current draw and pressure and allow the
compressor to run at 75 percent of capacity rather than
not at all. Once the time period has elapsed the full
capacity compressor solenoid will re-energize and try
again to run at full capacity. If the pressure or current is
exceeded again, the coil will again de-energize. This
sequence will repeat until the ambient temperature drops
or the line voltage increases enough that the trip values
are not exceeded.
The relay on the compressor control module is a single
pole double throw relay. The full capacity compressor
solenoid connects to the common terminal of the relay.
Once current is sensed by the compressor control module,
the relay closes and the second stage cooling call (if
present) is sent to the full capacity compressor solenoid.
This sequence prevents damage to the full capacity
compressor solenoid by ensuring that the solenoid is not
energized when the compressor is not running. A brief
time delay in this sequence also prevents locked rotor
amperage during start-up from tripping the device and
engaging the time delay period.
DEFROST CYCLE
The defrost cycle is controlled by temperature and time
on the solid state heat pump control. See Figure 12.
When the outdoor temperature is in the lower 40° F
temperature range or colder, the outdoor coil
temperature is 32° F or below. This coil temperature is
sensed by the coil temperature sensor mounted near the
bottom of the outdoor coil. Once coil temperature
reaches 30° F or below, the coil temperature sensor
sends a signal to the control logic of the heat pump
control and the defrost timer will start.
After 60 minutes at 30° F or below, the heat pump
control will place the system in the defrost mode.
During the defrost mode, the refrigerant cycle switches
back to the cooling cycle, the outdoor motor stops,
electric heaters are energized, and hot gas passing
through the outdoor coil melts any accumulated frost.
When the temperature rises to approximately 57° F, the
coil temperature sensor will send a signal to the heat
pump control which will return the system to heating
operations automatically.
If some abnormal or temporary condition such as a high
wind causes the heat pump to have a prolonged defrost
cycle, the heat pump control will restore the system to
heating operation automatically after 10 minutes.
The heat pump defrost control board has an option of
30, 60 or 90-minute setting. All models are shipped
from the factory on the 60-minute pin. If special
circumstances require a change to another time, remove
the wire from the 60-minute terminal and reconnect to
the desired terminal. The manufacturer's
recommendation is for 60-minute defrost cycles. Refer
to Figure 12.
FIGURE 12
DEFROST CONTROL BOARD
There is a cycle speed up jumper on the control. This
can be used to reduce the time between defrost cycle
operation without waiting for time to elapse.
Use a small screwdriver or other metallic object, or
another 1/4 inch QC, to short between the SPEEDUP
terminals to accelerate the HPC timer and initiate
defrost.
Be careful not to touch any other terminals with the
instrument used to short the SPEEDUP terminals. It
may take up to 10 seconds with the SPEEDUP terminals
shorted for the speedup to be completed and the defrost
cycle to start.
As soon as the defrost cycle kicks in remove the
shorting instrument from the SPEEDUP terminals.
Otherwise the timing will remain accelerated and run
through the 1-minute minimum defrost length sequence
in a matter of seconds and will automatically terminate
the defrost sequence.
There is an initiate defrost jumper (sen jump) on the
control that can be used at any outdoor ambient during
the heating cycle to simulate a 0° coil temperature. This
can be used to check defrost operation of the unit
without waiting for the outdoor ambient to fall into the
defrost region.
By placing a jumper across the SEN JMP terminals (a
1/4 inch QC terminal works best) the defrost sensor
mounted on the outdoor coil is shunted out and will
activate the timing circuit. This permits the defrost
cycle to be checked out in warmer weather conditions
without the outdoor temperature having to fall into the
defrost region.
In order to terminate the defrost test the SEN JMP
jumper must be removed. If left in place too long the
compressor could stop due to the high pressure control
opening because of high pressure condition created by
operating in the cooling mode with
outdoor fan off. Pressure will rise
fairly fast as there is likely no
actual frost on the outdoor coil in
this artificial test condition.
There is also a 5-minute compressor
time delay function built into the
HPC. This is to protect the
compressor from short cycling
conditions. In some instances, it is
helpful to the service technician to
override or speed up this timing
period, and shorting out the
SPEEDUP terminals for a few
seconds can do this.
Manual 2100-455A
Page
19 of 25
TROUBLESHOOTING
SOLID STATE HEAT PUMP CONTROL
TROUBLESHOOTING PROCEDURE
1. Turn on AC power supply to indoor and outdoor
units.
2. Turn thermostat blower switch to fan on. The indoor
blower should start. (If it doesn’t, troubleshoot
indoor unit and correct problem.)
3. Turn thermostat blower switch to auto position.
Indoor blower should stop.
4. Set system switch to heat or cool. Adjust thermostat
to call for heat or cool. The indoor blower,
compressor, and outdoor fan should start.
NOTE: If there was no power to 24 volt transformer,
the compressor and outdoor fan motor will not
start for 5 minutes. This is because of the
compressor short cycle protection.
TABLE 5
TROUBLESHOOTING
SYMPTOM
POSSIBLE CAUSES
Compressor
Control circuit wiring
contactor does not
energize (heating or
Compressor lock out
cooling).
Fan outdoor motor
does not run
(cooling or heating
except during
defrost).
WHAT TO CHECK
HOW TO CHECK OR REPAIR
Check for R connection at unit
and 24 volt between R - C
Run R connection to outdoor unit to power heat
pump control.
1. Check for 24V between
1. If no voltage between L1-C, turn thermostat
L1-C on heat pump control.
off and on again to reset high pressure
switch.
2. Check across high
2. If high pressure switch is open and will not
pressure switch
reset, replace high pressure switch.
Compressor short cycle
protection
Check for 24 V between CC-C If no voltage between CC-C, jumper speed up
and Y-C on heat pump control. terminal, and within 10 seconds power should
appear between CC-C. Remove speed up
jumper after 10 seconds.
Heat pump control
defective
Check all other possible
causes. Manual 2100-065.
Contactor defective
Check for open or shorted coil Replace contactor.
winding.
Power phasing not
correct
Check for red LED on phase
monitor (3 phase units only).
Switch two power leads to the unit.
Motor defective
Check for open or shorted
motor winding.
Replace motor.
Motor capacitor
defective
Check capacitor rating. Check Replace capacitor.
for open or shorted capacitor.
Heat pump control
defective
Check across fan relay on
heat pump control (Com-NC).
Replace heat pump control.
Replace heat pump control.
Reversing valve
does not energize
(heating only).
Reversing valve solenoid Check for open or shorted coil. Replace solenoid coil.
coil defective
Heat pump control
defective
Check for 24V between RV-C
and B-C.
Unit will not go into
defrost
(heating only).
Temperature sensor or
heat pump control
defective
Disconnect temperature
1. If unit goes through defrost cycle, replace
sensor from board and jumper
temperature sensor.
across speed up terminals and
sen jump terminals. This
2. If unit does not go through defrost cycle,
should cause the unit to go
replace heat pump control.
through a defrost cycle within
one minute.
Unit will not come
out of defrost
(heating only).
Temperature sensor or
heat pump control
defective
Jumper across speed up
terminals. This should cause
the unit to come out of defrost
within one minute.
Manual 2100-455A
Page
20 of 25
1. Check control circuit wiring.
2. Replace heat pump control.
1. If unit comes out of defrost cycle, replace
temperature sensor.
2. If unit does not come out of defrost cycle,
replace heat pump control.
CHECKING TEMPERATURE SENSOR
OUTSIDE UNIT CIRCUIT
1. Disconnect temperature sensor from board and from
outdoor coil.
2. Use an ohmmeter and measure the resistance of the
sensor. Also use ohmmeter to check for short or
open.
3. Check resistance reading to chart of resistance use
sensor ambient temperature. (Tolerance of part is
± 10%)
4. If sensor resistance reads very low, then sensor is
shorted and will not allow proper operation of the
heat pump control.
5. If sensor is out of tolerance, shorted, open, or reads
very low ohms then it should be replaced.
TEMPERATURE F VS RESISTANCE R OF TEMPERATURE
F
-25.0
-24.0
-23.0
-22.0
-21.0
-20.0
-19.0
-18.0
-17.0
-16.0
-15.0
-14.0
-13.0
-12.0
-11.0
-10.0
-9.0
-8.0
-7.0
-6.0
-5.0
-4.0
-3.0
-2.0
-1.0
0.0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
9.0
10.0
11.0
12.0
13.0
14.0
15.0
16.0
17.0
18.0
19.0
20.0
21.0
22.0
23.0
24.0
R
196871
190099
183585
177318
171289
165487
159904
154529
149355
144374
139576
134956
130506
126219
122089
118108
114272
110575
107010
103574
100260
97064
93981
91008
88139
85371
82699
80121
77632
75230
72910
70670
68507
66418
64399
62449
60565
58745
56985
55284
53640
52051
50514
49028
47590
46200
44855
43554
42295
41077
F
25.0
26.0
27.0
28.0
29.0
30.0
31.0
32.0
33.0
34.0
35.0
36.0
37.0
38.0
39.0
40.0
41.0
42.0
43.0
44.0
45.0
46.0
47.0
48.0
49.0
50.0
51.0
52.0
53.0
54.0
55.0
56.0
57.0
58.0
59.0
60.0
61.0
62.0
63.0
64.0
65.0
66.0
67.0
68.0
69.0
70.0
71.0
72.0
73.0
74.0
R
39898
38757
37652
36583
35548
34545
33574
32634
31723
30840
29986
29157
28355
27577
26823
26092
25383
24696
24030
23384
22758
22150
21561
20989
20435
19896
19374
18867
18375
17898
17434
16984
16547
16122
15710
15310
14921
14544
14177
13820
13474
13137
12810
12492
12183
11883
11591
11307
11031
10762
F
75.0
76.0
77.0
78.0
79.0
80.0
81.0
82.0
83.0
84.0
85.0
86.0
87.0
88.0
89.0
90.0
91.0
92.0
93.0
94.0
95.0
96.0
97.0
98.0
99.0
100.0
101.0
102.0
103.0
104.0
105.0
106.0
107.0
108.0
109.0
110.0
111.0
112.0
113.0
114.0
115.0
116.0
117.0
118.0
119.0
120.0
121.0
122.0
123.0
124.0
R
10501
10247
10000
9760
9526
9299
9077
8862
8653
8449
8250
8057
7869
7686
7507
7334
7165
7000
6840
6683
6531
6383
6239
6098
5961
5827
5697
5570
5446
5326
5208
5094
4982
4873
4767
4663
4562
4464
4367
4274
4182
4093
4006
3921
3838
3757
3678
3601
3526
3452
Manual 2100-455A
Page
21 of 25
COMPRESSOR SOLENOID
A nominal 24-volt direct current coil activates the
internal compressor solenoid. The input control circuit
voltage must be 18 to 28 volt ac. The coil power
requirement is 20 VA. The external electrical
connection is made with a molded plug assembly (PN
029-0311-00). This plug contains a full wave rectifier
to supply direct current to the unloader coil.
FIGURE 13
FAN BLADE SETTING
Compressor Solenoid Test Procedure – If it is
suspected that the unloader is not working, the
following methods may be used to verify operation.
1. Operate the system and measure compressor
amperage. Cycle the compressor solenoid on and
off at ten-second intervals. The compressor
amperage should go up or down at least 25 percent.
2. If step one does not give the expected results, shut
unit off. Apply 18 to 28 volt ac to the solenoid
molded plug leads and listen for a click as the
solenoid pulls in. Remove power and listen for
another click as the solenoid returns to its original
position.
3. If clicks can’t be heard, shut off power and remove
the control circuit molded plug from the compressor
and measure the solenoid coil resistance. The
resistance should be 32 to 60 ohms depending on
compressor temperature.
4. Next, check the molded plug.
Voltage check: Apply control voltage to the plug wires (18
to 28 volt ac). The measured dc voltage at the female
connectors in the plug should be around 15 to 27 vdc.
Resistance check: Measure the resistance from the end of
one molded plug lead to either of the two female
connectors in the plug. One of the connectors should read
close to zero ohms, while the other should read infinity.
Repeat with other wire. The same female connector as
before should read zero, while the other connector again
reads infinity. Reverse polarity on the ohmmeter leads and
repeat. The female connector that read infinity previously
should now read close to zero ohms.
Replace plug if either of these test methods does not
show the desired results.
FAN BLADE SETTING DIMENSIONS
Shown in Figure 13 are the correct fan blade setting
dimensions for proper air delivery across the outdoor
coil.
Any service work requiring removal or adjustment in
the fan and/or motor area will require that the
dimensions below be checked and blade adjusted in or
out on the motor shaft accordingly.
Manual 2100-455A
Page
22 of 25
TABLE 6
FAN BLADE DIMENSION
Model
Dimension A
A LL
1.0
REMOVAL OF FAN SHROUD
1. Disconnect all power to the unit.
2. Remove the screws holding both grilles, one on each
side of unit, and remove grilles.
3. Remove screws holding fan shroud to condenser and
bottom. Nine (9) screws.
4. Unwire condenser fan motor.
5. Slide complete motor, fan blade, and shroud
assembly out the left side of the unit.
6. Service motor/fan as needed.
7. Reverse steps to reinstall.
R-410A
REFRIGERANT CHARGE
The correct system R-410A charge is shown on the unit
rating plate. Optimum unit performance will occur with
a refrigerant charge shown on the unit serial plate.
If correct charge is in doubt, recover the refrigerant and
recharge per the charge on the unit rating plate. See
Table 7 for proper subcooling levels for evaluation of
proper charge.
TABLE 7 1
REFRIGERANT CHARGE - SUBCOOLING LEVEL
COOLING
HEATING
Model
Rated
Airflow
95 OD
80 OD
47 OD
35 OD
Temperature Temperature Temperature Temperature
CH3S1
1100
16 - 20
15 - 19
28 - 32
26 - 30
CH4S1
1500
18 - 22
17 - 21
20 - 24
15 - 19
CH5S1
1700
26 - 30
20 - 24
31 - 35
27 - 31
1 Expected subcooling levels during high capacity Stage 2 operation. Above subcooling levels are provided to troubleshoot low
charge or overcharged conditions. If charge is in doubt, evacuate and recharge the unit to the refrigerant charge listed on the
serial plate.
TABLE 8
INDOOR BLOWER PERFORMANCE
Model
Rated
ESP
1
Max
ESP
2
2nd Stage Cooling
2nd Stage Heating
3
1st Stage Cooling
1st Stage Heating
4
Blow er Only
or Vent Mode
Electric Heat
CH3S1
.15
.5
1100
800
800
1100
CH4S1
.2
.5
1500
1100
850
1700
CH5S1
.2
.5
1700
1300
850
1700
NOTE:
These units are equipped with a variable speed (ECM) indoor motor that automatically adjusts itself to maintain
approximately the same rate of indoor airflow in both heating and cooling, dry and wet coil conditions and at both 230/
208 or 460 volts.
1 Maximum ESP (inches WC) shown is with 2" thick disposable filter.
2 Rated CFM for 2nd Stage Operation – required for maximum performance rating.
3 1st Stage – the CFM output on 1st Stage Heating or Cooling.
4 Blower only CFM is the total air being circulated during continuous fan mode.
TABLE 9
MAXIMUM ESP OF OPERATION
High Speed
A LL
.5
Manual 2100-455A
Page
23 of 25
TABLE 10
PRESSURE TABLE
HIGH CAPACITY COOLING
MODEL
RETURN AIR
PRESSURE
TEMPERATURE
CH3S1
CH4S1
CH5S1
7 5 oF
8 0 oF
8 5 oF
9 0 oF
9 5 oF
1 0 0 oF 1 0 5 oF
110oF
115oF
75° D B
62° WB
LOW SIDE
HIGH SIDE
134
298
134
318
134
339
135
363
137
388
138
415
140
445
143
476
146
510
80° D B
67° WB
LOW SIDE
HIGH SIDE
143
306
143
326
143
348
144
372
146
398
148
426
150
456
153
488
156
523
85° D B
72° WB
LOW SIDE
HIGH SIDE
148
317
148
337
148
360
149
385
151
412
153
441
155
472
158
505
161
541
75° D B
62° WB
LOW SIDE
HIGH SIDE
131
308
133
332
135
356
137
380
138
406
139
431
139
456
140
483
140
509
80° D B
67° WB
LOW SIDE
HIGH SIDE
140
316
142
340
144
365
146
390
148
416
149
442
149
468
150
495
150
522
85° D B
72° WB
LOW SIDE
HIGH SIDE
145
327
147
352
149
378
151
404
153
431
154
457
154
484
155
512
155
540
75° D B
62° WB
LOW SIDE
HIGH SIDE
130
336
131
359
131
381
132
406
134
430
135
455
137
482
138
510
140
538
80° D B
67° WB
LOW SIDE
HIGH SIDE
139
345
140
368
140
391
141
416
143
441
144
467
146
494
148
523
150
552
85° D B
72° WB
LOW SIDE
HIGH SIDE
144
357
145
381
145
405
146
431
148
456
149
483
151
511
153
541
155
571
Low side pressure ± 2 PSIG
High side pressure ± 5 PSIG
Tables are based upon rated CFM (airflow) across the evaporator coil. If there is any doubt as to correct operating charge
being in the system, the charge should be removed, system evacuated and recharged to serial plate instruction.
TABLE 11
PRESSURE TABLE
LOW CAPACITY COOLING
MODEL
RETURN AIR
PRESSURE
TEMPERATURE
CH3S1
CH4S1
CH5S1
AIR TEMPERATURE ENTERING OUTDOOR COIL DEGREE F
7 5 oF
8 0 oF
8 5 oF
9 0 oF
9 5 oF
1 0 0 oF 1 0 5 oF
110oF
115oF
75° D B
62° WB
LOW SIDE
HIGH SIDE
139
259
140
284
141
308
142
333
143
359
145
385
147
410
149
438
151
464
80° D B
67° WB
LOW SIDE
HIGH SIDE
149
266
150
291
151
316
152
342
153
368
155
395
157
421
159
449
161
476
85° D B
72° WB
LOW SIDE
HIGH SIDE
154
275
155
301
156
327
157
354
158
381
160
409
162
436
165
465
167
493
75° D B
62° WB
LOW SIDE
HIGH SIDE
137
281
137
301
139
323
140
345
141
370
143
394
144
419
146
447
147
475
80° D B
67° WB
LOW SIDE
HIGH SIDE
146
288
147
309
149
331
150
354
151
379
153
404
154
430
156
458
157
487
85° D B
72° WB
LOW SIDE
HIGH SIDE
151
298
152
320
154
343
155
366
156
392
158
418
159
445
161
474
162
504
75° D B
62° WB
LOW SIDE
HIGH SIDE
136
293
137
316
139
340
141
364
142
389
143
413
144
439
145
464
145
489
80° D B
67° WB
LOW SIDE
HIGH SIDE
145
300
147
324
149
349
151
373
152
399
153
424
154
450
155
476
155
502
85° D B
72° WB
LOW SIDE
HIGH SIDE
150
311
152
335
154
361
156
386
157
413
158
439
159
466
160
493
160
520
Low side pressure ± 2 PSIG
High side pressure ± 5 PSIG
Tables are based upon rated CFM (airflow) across the evaporator coil. If there is any doubt as to correct operating charge
being in the system, the charge should be removed, system evacuated and recharged to serial plate instruction.
Manual 2100-455A
Page
24 of 25
Manual 2100-455A
Page
25 of 25
70°
70°
70°
CH3S
CH4S
CH5S
0 oF
44
290
54
280
44
272
PRESSURE
LOW SIDE
HIGH SIDE
LOW SIDE
HIGH SIDE
LOW SIDE
HIGH SIDE
46
277
55
281
46
295
5 oF
49
284
56
283
50
300
1 0 oF
53
293
56
284
54
303
1 5 oF
57
304
57
288
59
304
2 0 oF
63
316
61
294
64
309
2 5 oF
68
330
66
304
71
318
3 0 oF
75
346
74
317
78
330
3 5 oF
82
364
83
334
86
346
4 0 oF
90
383
94
353
95
364
4 5 oF
99
404
108
376
105
387
5 0 oF
AIR TEMPERATURE ENTERING OUTDOOR COIL DEGREE F
70°
70°
70°
CH3S
CH4S
CH5S
0 oF
46
275
60
270
58
275
PRESSURE
LOW SIDE
HIGH SIDE
LOW SIDE
HIGH SIDE
LOW SIDE
HIGH SIDE
56
274
65
271
49
280
5 oF
56
275
63
271
53
283
1 0 oF
58
279
61
273
57
283
1 5 oF
60
285
62
278
62
286
2 0 oF
64
294
64
284
68
291
2 5 oF
70
306
70
293
75
298
3 0 oF
77
321
77
303
83
308
3 5 oF
85
338
87
316
91
320
4 0 oF
95
358
99
331
101
334
4 5 oF
106
381
113
348
111
350
5 0 oF
AIR TEMPERATURE ENTERING OUTDOOR COIL DEGREE F
Low side pressure ± 2 PSIG
High side pressure ± 5 PSIG
Tables are based upon rated CFM (airflow) across the evaporator coil. If there is any doubt as to correct operating charge
being in the system, the charge should be removed, system evacuated and recharged to serial plate instruction.
RETURN AIR
TEMPERATURE
MODEL
LOW CAPACITY HEATING
TABLE 13
PRESSURE TABLE
Low side pressure ± 2 PSIG
High side pressure ± 5 PSIG
Tables are based upon rated CFM (airflow) across the evaporator coil. If there is any doubt as to correct operating charge
being in the system, the charge should be removed, system evacuated and recharged to serial plate instruction.
RETURN AIR
TEMPERATURE
MODEL
HIGH CAPACITY HEATING
TABLE 12
PRESSURE TABLE
119
406
130
367
122
369
5 5 oF
108
427
123
402
116
413
5 5 oF
133
434
149
388
134
389
6 0 oF
119
452
141
431
127
442
6 0 oF
148
465
170
411
146
412
6 5 oF
129
478
160
463
139
475
6 5 oF
Download PDF

advertising