Bard I42H1D Heat Pump User Manual

Product Description
Model EIR510-2xx-T
Documentation Number:
707 Dayton Road
--
EIR510-2xx-T_0708m
P.O. Box 1040
--
Ottawa, IL
61350 USA
Phone (815) 433-5100 -- General Fax (815) 433-5105
Phone (815) 433-5100 -- General Fax (815) 433-5105
Website: www.bb-elec.com
Sales e-mail: orders@bb-elec.com -- Fax (815) 433-5109
Technical Support e-mail: support@bb.elec.com -- Fax (815) 433-5104
European Headquarters
B&B Electronics
Westlink Commercial Park -- Oranmore, Co. Galway, Ireland
Phone +353 91-792444 -- Fax +353 91-792445
Website: www.bb-europe.com
Sales e-mail: sales@bb-europe.com
Technical Support e-mail: support@bb-europe.com
© 2008 B&B Electronics Mfg. Co. Inc.
-
Revised February 2008
Manual Documentation Number: EIR510-2xx-T-0708m
1
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Ten Port Managed Industrial
Ethernet Switches
User Manual
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
FCC
This Equipment has been tested and found to comply with the limits for a
Class-A digital device, pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference.
This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
„
Reorient or relocate the receiving antenna.
„
Increase the separation between the equipment and receiver.
„
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
„
Consult the dealer or an experienced radio/TV technician for help.
CE
This is a Class-A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take
adequate measures.
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Content
Introduction ................................................................ 1 Features ................................................................... 1 Package Contents .................................................... 3 Hardware Description ................................................ 4 Physical Dimension (W x D x H) .............................. 4 Front Panel ............................................................... 4 Bottom View ............................................................. 5 LED Indicators .......................................................... 6 Ports ......................................................................... 7 Cabling ..................................................................... 9 Wiring the Power Inputs ......................................... 10 Wiring the Fault Alarm Contact .............................. 11 Mounting Installation ............................................... 12 DIN-Rail Mounting .................................................. 12 Panel Mounting ...................................................... 14 Hardware Installation .............................................. 15 Installation Steps .................................................... 15 Network Application ................................................ 16 B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
X-Ring Application .................................................. 16 Coupling Ring Application ...................................... 17 Dual Homing Application ........................................ 18 Console Management .............................................. 19 Connecting to the Console Port ............................. 19 Login in the Console Interface ............................... 19 CLI Management .................................................... 20 Commands Level ............................................................. 21 Commands Set List .......................................................... 22 Web-Based Management ........................................ 46 About Web-based Management ............................ 46 Preparing for Web Management ............................ 46 System Login.......................................................... 47 System Information ................................................ 48 IP Configuration ..................................................... 48 DHCP Server – System configuration .................... 49 DHCP Client – System Configuration .................... 50 DHCP Server - Port and IP Bindings ..................... 50 TFTP - Update Firmware ....................................... 51 B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
TFTP – Restore Configuration ............................... 52 TFTP - Backup Configuration ................................. 52 System Event Log – Syslog Configuration ............. 53 System Event Log - SMTP Configuration .............. 54 System Event Log - Event Configuration ............... 55 Fault Relay Alarm ................................................... 56 SNTP Configuration ............................................... 57 IP Security .............................................................. 60 User Authentication ................................................ 61 Port Statistics ......................................................... 61 Port Control ............................................................ 62 Port Trunk............................................................... 63 Aggregator setting ............................................................ 63 Aggregator Information ..................................................... 65 State Activity ..................................................................... 65 Port Mirroring.......................................................... 66 Rate Limiting .......................................................... 67 VLAN configuration ................................................ 68 VLAN configuration - Port-based VLAN ........................... 69 802.1Q VLAN ................................................................... 71 B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Rapid Spanning Tree ............................................. 73 RSTP System Configuration............................................. 73 RSTP Port Configuration .................................................. 75 SNMP Configuration .............................................. 76 System Configuration ....................................................... 76 Trap Configuration ............................................................ 77 SNMPV3 Configuration .................................................... 78 QoS Configuration .................................................. 81 QoS Policy and Priority Type ........................................... 81 Port Base Priority ............................................................. 83 COS Configuration ........................................................... 83 TOS Configuration ............................................................ 83 IGMP Configuration ................................................ 84 X-Ring .................................................................... 85 802.1X/Radius Configuration ........................................... 87 MAC Address Table ......................................................... 90 Factory Default ....................................................... 92 Save Configuration ................................................. 93 System Reboot ....................................................... 93 Trouble shooting...................................................... 94 B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Technical Specification ........................................... 95 B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Introduction
This managed industrial switch is a cost-effective solution and meets the
high reliability requirements demanded by industrial applications. The 8
10/100TX plus 2 100FX managed industrial switch can be easily managed
through a Web GUI. The fiber ports extend the connection distance,
increasing network elasticity and performance.
Features
„
„
„
System Interface/Performance
¾
RJ-45 ports with Auto MDI/MDI-X
¾
Store-and-Forward Switching Architecture
¾
Back-plane (Switching Fabric): 2Gbps
¾
1Mbits Packet Buffer
¾
8K MAC Address Table
Power Supply
¾
Wide-range Redundant Power Design
¾
Reverse Polarity Protection
VLAN
¾
Port Based VLAN
¾
Support 802.1 Q Tag VLAN
¾
GVRP
„
Port Trunk with LACP
„
QoS (Quality of Service)
„
¾
IEEE 802.1p Class of Service,
¾
4 priority queues per port
¾
Port Base, Tag Base and Type of Service
Port Mirror: Monitor traffic in switched networks.
¾
TX Packet only
¾
RX Packet only
¾
TX and RX Packet
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
1
„
¾
Port Security : MAC address entries/filter
¾
IP Security : IP address security management
¾
Login Security: IEEE802.1X/RADIUS
„
IGMP with Query mode for Multi Media Application
„
Case/Installation
„
„
„
„
„
„
2
Security
¾
IP-30 Protection
¾
DIN Rail and Panel Mount Design
Spanning Tree
¾
IEEE802.1d Spanning Tree
¾
IEEE802.1w Rapid Spanning Tree
X-ring
¾
X-ring, Dual Homing, and Couple Ring Topology
¾
Redundant backup feature with recovery time below 300ms
Bandwidth Control
¾
Ingress Packet Filter and Egress Rate Limit
¾
Broadcast/Multicast Packet Filter Control
System Event Log
¾
System Log Server/Client
¾
SMTP e-mail Alert
¾
Relay Alarm Output System Events
SNMP Trap
¾
Cold Start
¾
Power status
¾
Authentication failure
¾
X-ring topology changed
¾
Port Link up/Link down
TFTP Firmware Update, System Configuration backup and restoration.
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Package Contents
„
One Managed industrial switch
„
One CD ROM containing a user manual
„
RS-232/RJ-45 cable
„
2 panel mount plates with 6 screws
„
One DIN-Rail Clip (attached on the switch)
If any items are missing, contact B&B Electronics for a replacement.
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
3
Hardware Description
Physical Dimension (W x D x H)
2.9 x 4.2 x 6.4 in (7.4 x 10.7 x 16.3 cm)
Front Panel
Front Panel of the industrial switch
4
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Bottom View
Bottom Panel of the industrial switch
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
5
LED Indicators
LED
Status
Meaning
Green
The switch is powered on
Off
The switch is powered off
Green
Power source 1 is available.
Off
Power source 1 is unavailable
Green
Power source 2 is available.
Off
Power source 2 is unavailable
PWR
PWR1
PWR2
Orange
Fault
Off
Green
Power or port failure (See alarm
setting for operational details)
Normal Operation
The switch is the master of an
X-Ring group
R.M.
Off
LNK/ACT
The switch is not the master of an
X-Ring group
Green
Fiber port linked
Blinks
Fiber port transmitting or receiving
Off
No device attached
Orange
Full-duplex mode
Blinking
(Orange)
P1 through P8
Off
Half duplex or no device attached.
Green
Network device detected.
Blinking
(Green)
Transmitting or receiving
Off
6
Collision
No device attached
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Ports
„
RJ-45 ports
There are 8x 10/100Mbps auto-sensing ports with MDI/MDIX. The switch
can connect to another switch or workstation without changing between
straight through or crossover cabling.
RJ-45 Pin Assignments
Pin Number
Assignment
1
Tx+
2
Tx-
3
Rx+
6
Rx-
Straight Through Cable Schematic
Cross Over Cable Schematic
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
7
„
Fiber Port
There are two 100Base-FX ports. The fiber port is SC or ST type connectors
in multi mode (2Km) or single mode (30Km).
Connect the fiber ports as shown below (Transmit to distant end receive and
vice versa).
ATTENTION
This is a Class 1 Laser/LED product. Do not stare into
the Laser/LED Beam.
8
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Cabling
„
Use Category 5 cabling for RJ-45 port connection. The cable between
the switch and the network device (switch, hub, workstation, etc.) must
be less than 328 feet (100 meters) long.
„
Single-mode fiber ports must use 9/125 um single-mode fiber cable.
The cable length can be up to 30 Kilometers.
„
Multi-mode fiber ports must use 50 or 62.5/125 um multi-mode fiber
cable. The cable length can be up to 2Kilometers.
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
9
Wiring the Power Inputs
V- V+
V- V+
1. Insert the positive and negative wires into the V+ and Vcontacts on the terminal block connector.
2. To tighten the wire-clamp screws.
[NOTE] Use 12 to 24 AWG wire.
10
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Wiring the Fault Alarm Contact
1A@24V
Insert the wires into the fault alarm contact
[NOTE] Use 12 to 24 AWG wire.
[NOTE] Relay contacts are normally open.
[NOTE] The Relay Alarm also requires software configuration. Refer to the
Web Based Management Fault Relay Alarm Section.
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
11
Mounting Installation
DIN-Rail Mounting
Rear Panel of
the switch
DIN-Rail
1. Use the screws to attach the DIN-Rail to the switch
12
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
1.
Insert the top of DIN-Rail into the track.
2.
Lightly push the DIN-Rail into the track.
3.
Ensure the DIN-Rail is tightly on the track.
4.
To remove the industrial switch from the track, reverse steps above.
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
13
Panel Mounting
1. Remove the DIN-Rail Clip.
2. Place the panel mount plate on the rear panel of the industrial switch.
3. Use the screws to attach the panel mount plate.
4. Use the hook holes at the corners to attach the switch to the panel.
14
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Hardware Installation
Installation Steps
1. Unpack the switch
2. Attach the switch to the DIN-Rail or panel.
3. Apply power to the switch.
4. Connect the switch to the network devices.
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
15
Network Application
X-Ring Application
This switch incorporates the X-Ring Protocol to ensure network reliability
and system restoration within 300 ms in the event of a connection failure.
The X-Ring algorithm is similar to the spanning tree protocol (STP)
algorithm but it has faster recovery time. The following figure below is an
example of an X-Ring application.
16
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Coupling Ring Application
If the network has more than one X-Ring group, the coupling ring function is
used to connect them and add redundancy. This ensures that transmissions
between the two ring groups will not fail. The figure below is an example of
the coupling ring application.
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
17
Dual Homing Application
The Dual Homing function is used to prevent a connection loss between the
X-Ring group and the upper level/core switch. Assign a port in each X-ring
group to be the Dual Homing ports The Dual Homing function can only be
used when the X-Ring function is active. Each X-Ring group can have one
Dual Homing port. Note: The upper level switches must have RSTP
enabled.
18
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Console Management
Connecting to the Console Port
Attach the DB9 end to a PC or terminal and the RJ-45 end to the console
port on the switch. The PC must have support a terminal emulation
program.
DB9 Connector RJ-45 Connector
NC
1
Orange/White
2
2
Orange
3
3
Green/White
NC
4
Blue
5
5
Blue/White
NC
6
Green
NC
7
Brown/White
NC
8
Brown
Login in the Console Interface
When the connection between Switch and PC is ready, turn on the PC, run
a terminal emulation program or Hyper Terminal, and configure the
following communication parameters:
Baud Rate: 9600 bps
Data Bits: 8
Parity: none
Stop Bit: 1
Flow control: None
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
19
The settings of communication parameters
After entering the parameters, click ‘OK’. When the blank screen shows up,
press Enter on the PC keyboard. A login screen will be displayed. Enter
‘root’ for the User name and Password.
Console login interface
CLI Management
After you login to the system, you will see a command prompt. To enter CLI
management interface, type ‘enable’ and press enter.
20
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
CLI command interface
Commands Level
Access
Modes
Method
Prompt
Exit
Method
About This Mode1
The user commands
available at the user
level are a subset of
Begin a
User EXEC
session with
switch>
your switch.
Enter logout
or quit.
those available at the
privileged level.
Use this mode to
• Perform basic tests.
• Displays system
information.
The privileged
Enter the
Privileged
EXEC
command is advance
enable
command
while in user
switch#
Enter
mode
disable to
Privileged this mode to
exit.
•Displays advance
EXEC mode.
function status
• Save configures
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
21
Enter the
To exit to
configure
Global
command
switch
Configuration
while in
(config)#
privileged
privileged
EXEC
mode, enter
exit or end
EXEC mode.
Use this mode to
configure parameters
that apply to your
switch as a whole.
Enter the vlan
database
To exit to
Use this mode to
VLAN
command
switch
user EXEC
configure
database
while in
(vlan)#
mode, enter
VLAN-specific
exit.
parameters.
privileged
EXEC mode.
To exit to
Enter the
global
interface
configuratio
command
(with a
Interface
configuration
specific
interface)
n mode,
Use this mode to
switch
enter exit.
configure parameters
(config-if)#
To exist to
for the switch and
privileged
Ethernet ports.
while in global
EXEC
configuration
mode, or
mode
end.
Commands Set List
22
User EXEC
E
Privileged EXEC
P
Global configuration
G
VLAN database
V
Interface configuration
I
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
System Commands Set
Commands
Level Description
show config
E
Show switch
Example
switch>show config
configuration
show terminal
P
Show console
switch#show terminal
information
write memory
P
Save user
switch#write memory
configuration into
permanent memory
(flash rom)
system name
G
G
[System Location]
system description
G
[System Description]
system contact
G
Set switch system
switch(config)#system location
location string
xxx
Set switch system
switch(config)#system
description string
description xxx
Set switch system
switch(config)#system contact
contact window string xxx
[System Contact]
show system-info
switch(config)#system name xxx
name
[System Name]
system location
Configure system
E
Show system
switch>show system-info
information
ip address
G
[Ip-address]
Configure the IP
switch(config)#ip address
address of switch
192.168.1.1 255.255.255.0
[Subnet-mask]
192.168.1.254
[Gateway]
ip dhcp
G
Enable DHCP client
switch(config)#ip dhcp
function of switch
show ip
P
Show IP information of switch#show ip
switch
no ip dhcp
G
Disable DHCP client
switch(config)#no ip dhcp
function of switch
reload
G
Halt and perform a cold
restart
switch(config)#reload
default
G
Restore to default
switch(config)#default
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
23
admin username
G
[Username]
Changes a login
switch(config)#admin username
username.
xxxxxx
(maximum 10 words)
admin password
G
[Password]
show admin
P
Specifies a password switch(config)#admin password
(maximum 10 words)
xxxxxx
Show administrator
switch#show admin
information
dhcpserver enable
G
Enable DHCP Server switch(config)#dhcpserver enable
Dhcpserver disable
G
Disable DHCP Server switch(config)#no dhcpserver
dhcpserver lowip
G
Configure low IP
switch(config)#dhcpserver lowip
address for IP pool
192.168.1.100
Configure high IP
switch(config)#dhcpserver highip
address for IP pool
192.168.1.200
Configure subnet
switch(config)#dhcpserver
[Low IP]
dhcpserver highip
G
[High IP]
dhcpserver subnetmask
G
mask for DHCP clients subnetmask 255.255.255.0
[Subnet mask]
dhcpserver gateway
G
[Gateway]
dhcpserver dnsip
G
[DNS IP]
dhcpserver leasetime
G
[Hours]
dhcpserver ipbinding
I
Configure gateway for switch(config)#dhcpserver
DHCP clients
gateway 192.168.1.254
Configure DNS IP for
switch(config)#dhcpserver dnsip
DHCP clients
192.168.1.1
Configure lease time
switch(config)#dhcpserver
(in hour)
leasetime 1
Set static IP for DHCP switch(config)#interface
clients by port
[IP address]
fastEthernet 2
switch(config)#dhcpserver
ipbinding 192.168.1.1
show dhcpserver
P
Show configuration of switch#show dhcpserver
DHCP server
configuration
show dhcpserver clients
P
configuration
Show client entries of switch#show dhcpserver clients
DHCP server
show dhcpserver
P
ip-binding
Show IP-Binding
switch#show dhcpserver
information of DHCP
ip-binding
server
no dhcpserver
G
Disable DHCP server switch(config)#no dhcpserver
function
24
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
security enable
G
Enable IP security
switch(config)#security enable
function
security http
G
Enable IP security of
switch(config)#security http
HTTP server
security telnet
G
Enable IP security of
switch(config)#security telnet
telnet server
security ip
G
Set the IP security list switch(config)#security ip 1
[Index(1..10)] [IP
192.168.1.55
Address]
show security
P
Show the information
switch#show security
of IP security
no security
G
Disable IP security
switch(config)#no security
function
no security http
G
Disable IP security of
switch(config)#no security http
HTTP server
no security telnet
G
Disable IP security of
switch(config)#no security telnet
telnet server
Port Commands Set
Commands
Level Description
interface fastEthernet
G
[Portid]
duplex
I
[full | half]
Example
Choose the port for
switch(config)#interface
modification.
fastEthernet 2
Use the duplex
switch(config)#interface
configuration
fastEthernet 2
command to specify
switch(config-if)#duplex full
the duplex mode of
operation for Fast
Ethernet.
speed
I
[10|100|1000|auto]
Use the speed
switch(config)#interface
configuration
fastEthernet 2
command to specify
switch(config-if)#speed 100
the speed mode of
operation for Fast
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
25
Ethernet., the speed
can’t be set to 1000 if
the port isn’t a giga
port..
no flowcontrol
I
Disable flow control of switch(config-if)#no flowcontrol
interface
security enable
I
Enable security of
switch(config)#interface
interface
fastEthernet 2
switch(config-if)#security enable
no security
I
Disable security of
switch(config)#interface
interface
fastEthernet 2
switch(config-if)#no security
bandwidth type all
I
Set interface ingress
switch(config)#interface
limit frame type to
fastEthernet 2
“accept all frame”
switch(config-if)#bandwidth type
all
Set interface ingress
switch(config)#interface
broadcast-multicast-floo
limit frame type to
fastEthernet 2
ded-unicast
“accept broadcast,
switch(config-if)#bandwidth type
bandwidth type
I
multicast, and flooded broadcast-multicast-flooded-uni
bandwidth type
I
broadcast-multicast
unicast frame”
cast
Set interface ingress
switch(config)#interface
limit frame type to
fastEthernet 2
“accept broadcast and switch(config-if)#bandwidth type
bandwidth type
I
broadcast-only
multicast frame”
broadcast-multicast
Set interface ingress
switch(config)#interface
limit frame type to
fastEthernet 2
“only accept broadcast switch(config-if)#bandwidth type
bandwidth in
[Value]
I
frame”
broadcast-only
Set interface input
switch(config)#interface
bandwidth. Rate
fastEthernet 2
Range is from 100
switch(config-if)#bandwidth in 100
kbps to 102400 kbps
or to 256000 kbps for
26
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
giga ports,
and zero means no
limit.
bandwidth out
Set interface output
switch(config)#interface
[Value]
bandwidth. Rate
fastEthernet 2
Range is from 100
switch(config-if)#bandwidth out
kbps to 102400 kbps
100
or to 256000 kbps for
giga ports,
and zero means no
limit.
show bandwidth
I
Show interfaces
switch(config)#interface
bandwidth control
fastEthernet 2
switch(config-if)#show bandwidth
state
I
[Enable | Disable]
Use the state interface switch(config)#interface
configuration
fastEthernet 2
command to specify
(config-if)#state Disable
the state mode of
operation for Ethernet
ports. Use the disable
form of this command
to disable the port.
show interface
I
configuration
show interface
switch(config)#interface
configuration status
fastEthernet 2
switch(config-if)#show interface
configuration
show interface status
I
show interface actual
switch(config)#interface
status
fastEthernet 2
(config-if)#show interface status
show interface
accounting
I
show interface statistic switch(config)#interface
counter
fastEthernet 2
(config-if)#show interface
accounting
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
27
no accounting
I
Clear interface
switch(config)#interface
accounting information fastEthernet 2
switch(config-if)#no accounting
Trunk Commands Set
Commands
Level Description
aggregator priority
G
[1~65535]
aggregator activityport
G
Example
Set port group system switch(config)#aggregator priority
priority
22
Set activity port
switch(config)#aggregator
[Group ID]
activityport 2
[Port Numbers]
Assign a trunk group
switch(config)#aggregator group
[GroupID] [Port-list]
with LACP active.
1 1-4 lacp workp 2
lacp
[GroupID] :1~3
or
workp
[Port-list]:Member port switch(config)#aggregator group
[Workport]
list, This parameter
aggregator group
G
2 1,4,3 lacp workp 3
could be a port
range(ex.1-4) or a port
list separate by a
comma(ex.2, 3, 6)
[Workport]: The
amount of work ports,
this value could not be
less than zero or be
large than the amount
of member ports.
Assign a static trunk
switch(config)#aggregator group
[GroupID] [Port-list]
group.
1 2-4 nolacp
nolacp
[GroupID] :1~3
or
aggregator group
G
[Port-list]:Member port switch(config)#aggregator group
list, This parameter
1 3,1,2 nolacp
could be a port
range(ex.1-4) or a port
list separate by a
28
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
comma(ex.2, 3, 6)
show aggregator
P
Show the information
switch#show aggregator 1
of trunk group
or
switch#show aggregator 2
or
switch#show aggregator 3
no aggregator lacp
G
Disable the LACP
switch(config)#no aggreator lacp
function of trunk group 1
[GroupID]
no aggregator group
G
Remove a trunk group switch(config)#no aggreator
[GroupID]
group 2
VLAN Commands Set
Commands
Level Description
vlan database
P
Example
Enter VLAN configure switch#vlan database
mode
Vlanmode
V
[portbase| 802.1q |
To set switch VLAN
switch(vlan)#vlanmode portbase
mode.
or
switch(vlan)#vlanmode 802.1q
gvrp]
or
switch(vlan)#vlanmode gvrp
no vlan
V
No VLAN
Switch(vlan)#no vlan
Ported based VLAN configuration
vlan port-based
grpname
V
Add new port based
switch(vlan)#vlan port-based
VALN
grpname test grpid 2 port 2-4
[Group Name]
or
grpid
switch(vlan)#vlan port-based
[GroupID]
grpname test grpid 2 port 2,3,4
port
[PortNumbers]
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
29
show vlan [GroupID]
or
show vlan
V
no vlan group
[GroupID]
V
Show VLAN
switch(vlan)#show vlan 23
information
Delete port base group switch(vlan)#no vlan group 2
ID
IEEE 802.1Q VLAN
vlan 8021q name
[GroupName]
vid
[VID]
V
Change the name of
switch(vlan)#vlan 8021q name
VLAN group, if the
test vid 22
group didn’t exist, this
command can’t be
applied.
vlan 8021q port
[PortNumber]
access-link untag
[UntaggedVID]
V
Assign an access link switch(vlan)#vlan 8021q port 3
for VLAN by port, if the access-link untag 33
port belongs to a trunk
group, this command
can’t be applied.
vlan 8021q port
[PortNumber]
V
Assign a trunk link for switch(vlan)#vlan 8021q port 3
trunk-link tag
VLAN by port; if the
[TaggedVID List]
port belongs to a trunk or
vlan 8021q port
[PortNumber]
hybrid-link untag
[UntaggedVID]
tag
[TaggedVID List]
V
trunk-link tag 2,3,6,99
group, this command
switch(vlan)#vlan 8021q port 3
can’t be applied.
trunk-link tag 3-20
Assign a hybrid link for switch(vlan)#vlan 8021q port 3
VLAN by port; if the
hybrid-link untag 4 tag 3,6,8
port belongs to a trunk or
vlan 8021q trunk
[PortNumber]
access-link untag
[UntaggedVID]
V
vlan 8021q trunk
[PortNumber]
V
group, this command
switch(vlan)#vlan 8021q port 3
can’t be applied.
hybrid-link untag 5 tag 6-8
Assign a access link
switch(vlan)#vlan 8021q trunk 3
for VLAN by trunk
access-link untag 33
group
Assign a trunk link for switch(vlan)#vlan 8021q trunk 3
VLAN by trunk group
trunk-link tag
trunk-link tag 2,3,6,99
or
[TaggedVID List]
switch(vlan)#vlan 8021q trunk 3
trunk-link tag 3-20
vlan 8021q trunk
[PortNumber]
30
V
Assign a hybrid link for switch(vlan)#vlan 8021q trunk 3
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
VLAN by trunk group
hybrid-link untag
[UntaggedVID]
tag
[TaggedVID List]
hybrid-link untag 4 tag 3,6,8
or
switch(vlan)#vlan 8021q trunk 3
hybrid-link untag 5 tag 6-8
show vlan [GroupID]
or
show vlan
V
no vlan group
[GroupID]
V
Show VLAN
switch(vlan)#show vlan 23
information
Delete port base group switch(vlan)#no vlan group 2
ID
Spanning Tree Commands Set
Commands
Level Description
spanning-tree enable
G
Example
Enable spanning tree switch(config)#spanning-tree
enable
spanning-tree priority
G
Configure spanning
switch(config)#spanning-tree
tree priority parameter priority 32767
[0~61440]
spanning-tree max-age
[seconds]
G
Use the spanning-tree switch(config)#spanning-tree
max-age global
max-age 15
configuration
command to change
the interval between
messages the
spanning tree receives
from the root switch. If
a switch does not
receive a bridge
protocol data unit
(BPDU) message from
the root switch within
this interval, it
recomputed the
Spanning Tree
Protocol (STP)
topology.
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
31
spanning-tree
G
Use the spanning-tree switch(config)#spanning-tree
hello-time global
hello-time [seconds]
hello-time 3
configuration
command to specify
the interval between
hello bridge protocol
data units (BPDUs).
spanning-tree
G
Use the spanning-tree switch(config)#spanning-tree
forward-time global
forward-time [seconds]
forward-time 20
configuration
command to set the
forwarding-time for the
specified
spanning-tree
instances. The
forwarding time
determines how long
each of the listening
and learning states
last before the port
begins forwarding.
stp-path-cost
[1~200000000]
I
Use the spanning-tree switch(config)#interface
cost interface
fastEthernet 2
configuration
switch(config-if)#stp-path-cost 20
command to set the
path cost for Spanning
Tree
Protocol (STP)
calculations. In the
event of a loop,
spanning tree
considers the path
cost when selecting
an interface to place
32
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
into the forwarding
state.
stp-path-priority
I
[Port Priority]
Use the spanning-tree switch(config)#interface
port-priority interface
fastEthernet 2
configuration
switch(config-if)#stp-path-priority
command to configure 128
a port priority that
is used when two
switches tie for
position as the root
switch.
stp-admin-p2p
I
[Auto|True|False]
Admin P2P of STP
switch(config)#interface
priority on this
fastEthernet 2
interface.
switch(config-if)#stp-admin-p2p
Auto
stp-admin-edge
I
[True|False]
Admin Edge of STP
switch(config)#interface
priority on this
fastEthernet 2
interface.
switch(config-if)#stp-admin-edge
True
stp-admin-non-stp
I
[True|False]
Admin NonSTP of STP switch(config)#interface
priority on this
fastEthernet 2
interface.
switch(config-if)#stp-admin-non-s
tp False
show spanning-tree
E
Displays a summary of switch>show spanning-tree
the spanning-tree
states.
no spanning-tree
G
Disable spanning-tree. switch(config)#no spanning-tree
QOS Commands Set
Commands
Level Description
qos policy
G
[weighted-fair|strict]
qos prioritytype
G
Example
Select QOS policy
switch(config)#qos policy
scheduling
weighted-fair
Setting of QOS priority switch(config)#qos prioritytype
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
33
type
[port-based|cos-only|tos
-only|cos-first|tos-first]
qos priority portbased
[Port]
[lowest|low|middle|high]
G
qos priority cos
[Priority][lowest|low|middle|h
igh]
G
qos priority tos
G
Configure TOS Priority switch(config)#qos priority tos 3
high
P
Displays the
Configure Port-based switch(config)#qos priority
Priority
portbased 1 low
Configure COS Priority switch(config)#qos priority cos 0
middle
[Priority][lowest|low|mid
dle|high]
show qos
Switch#show qos
information of QoS
configuration
no qos
G
Disable QoS function
switch(config)#no qos
IGMP Commands Set
Commands
igmp enable
Level Description
G
Enable IGMP
Example
switch(config)#igmp enable
snooping function
Igmp-query auto
G
Set IGMP query to
switch(config)#Igmp-query auto
auto mode
Igmp-query force
G
Set IGMP query to
switch(config)#Igmp-query force
force mode
show igmp
P
Displays the details of switch#show igmp configuration
an IGMP
configuration
configuration.
show igmp multi
P
Displays the details of switch#show igmp multi
an IGMP snooping
entries.
no igmp
G
Disable IGMP
switch(config)#no igmp
snooping function
no igmp-query
34
G
Disable IGMP query
switch#no igmp-query
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Mac / Filter Table Commands Set
Commands
Level Description
Example
Configure MAC
switch(config)#interface
hwaddr
address table of
fastEthernet 2
[MAC]
interface (static).
switch(config-if)#mac-address-tab
mac-address-table static
I
le static hwaddr 000012345678
mac-address-table filter
G
hwaddr
Configure MAC
switch(config)#mac-address-table
address table(filter)
filter hwaddr 000012348678
[MAC]
show mac-address-table
P
Show all MAC address switch#show mac-address-table
table
show mac-address-table
P
static
show mac-address-table
P
filter
no mac-address-table
I
Show static MAC
switch#show mac-address-table
address table
static
Show filter MAC
switch#show mac-address-table
address table.
filter
Remove an entry of
switch(config)#interface
static hwaddr
MAC address table of fastEthernet 2
[MAC]
interface (static)
switch(config-if)#no
mac-address-table static hwaddr
000012345678
Remove an entry of
switch(config)#no
filter hwaddr
MAC address table
mac-address-table filter hwaddr
[MAC]
(filter)
000012348678
no mac-address-table
no mac-address-table
G
G
Remove dynamic entry switch(config)#no
of MAC address table mac-address-table
SNMP Commands Set
Commands
Level Description
snmp system-name
G
[System Name]
snmp system-location
G
[System Location]
snmp system-contact
G
Example
Set SNMP agent
switch(config)#snmp
system name
system-name l2switch
Set SNMP agent
switch(config)#snmp
system location
system-location lab
Set SNMP agent
switch(config)#snmp
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
35
system contact
[System Contact]
snmp agent-mode
G
Select the agent mode switch(config)#snmp agent-mode
of SNMP
[v1v2c|v3|v1v2cv3]
G
snmp
v1v2cv3
Add SNMP community switch(config)#snmp
string.
community-strings
system-contact where
community-strings public right
rw
[Community]
right
[RO/RW]
G
snmp-server host
Configure SNMP
switch(config)#snmp-server host
[IP address]
server host information 192.168.1.50 community public
community
and community string trap-version v1
[Community-string]
(remove)
trap-version
Switch(config)#
[v1|v2c]
no snmp-server host
192.168.1.50
snmpv3 context-name
G
Configure the context switch(config)#snmpv3
name
context-name Test
Configure the
switch(config)#snmpv3 user
[User Name]
userprofile for
test01 group G1 password
group
SNMPV3 agent.
AuthPW PrivPW
[Group Name]
Privacy password
password
could be empty.
[Context Name ]
G
snmpv3 user
[Authentication
Password] [Privacy
Password]
Configure the access
switch(config)#snmpv3 access
context-name [Context
table of SNMPV3
context-name Test group G1
Name ]
agent
security-level AuthPriv
G
snmpv3 access
match-rule Exact views V1 V1 V1
group
[Group Name ]
security-level
[NoAuthNoPriv|AuthNoP
riv|AuthPriv]
match-rule
36
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
[Exact|Prifix]
views
[Read View Name] [Write
View Name] [Notify View
Name]
snmpv3 mibview view
G
Configure the mibview switch(config)#snmpv3 mibview
[View Name]
table of SNMPV3
view V1 type Excluded sub-oid
type
agent
1.3.6.1
Show SNMP
switch#show snmp
[Excluded|Included]
sub-oid
[OID]
show snmp
P
configuration
no snmp
G
community-strings
Remove the specified switch(config)#no snmp
community.
community-strings public
Remove the SNMP
switch(config)#no snmp-server
server host.
192.168.1.50
[Community]
no snmp-server host
G
[Host-address]
no snmpv3 user
G
Remove specified user switch(config)#no snmpv3 user
of SNMPv3 agent.
Test
Remove specified
switch(config)#no snmpv3 access
context-name [Context
access table of
context-name Test group G1
Name ]
SNMPv3 agent.
security-level AuthPr
[User Name]
no snmpv3 access
G
group
iv match-rule Exact views V1 V1
[Group Name ]
V1
security-level
[NoAuthNoPriv|AuthNoP
riv|AuthPriv]
match-rule
[Exact|Prifix]
views
[Read View Name] [Write
View Name] [Notify View
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
37
Name]
Remove specified
switch(config)#no snmpv3
view
mibview table of
mibview view V1 type Excluded
[View Name]
SNMPV3 agent.
sub-oid 1.3.6.1
G
no snmpv3 mibview
type
[Excluded|Included]
sub-oid
[OID]
Port Mirroring Commands Set
Commands
Level Description
monitor rx
G
Set RX destination
Example
switch(config)#monitor rx
port of monitor function
monitor tx
G
Set TX destination port switch(config)#monitor tx
of monitor function
show monitor
P
Show port monitor
switch#show monitor
information
monitor
I
Configure source port switch(config)#interface
of monitor function
[RX|TX|Both]
fastEthernet 2
switch(config-if)#monitor RX
show monitor
I
Show port monitor
switch(config)#interface
information
fastEthernet 2
switch(config-if)#show monitor
no monitor
I
Disable source port of switch(config)#interface
monitor function
fastEthernet 2
switch(config-if)#no monitor
802.1x Commands Set
Commands
Level Description
8021x enable
G
Example
Use the 802.1x global switch(config)# 8021x enable
configuration
command to enable
802.1x protocols.
8021x system radiousip
38
G
Use the 802.1x system switch(config)# 8021x system
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
radious IP global
[IP address]
radiousip 192.168.1.1
configuration
command to change
the radious server IP.
8021x system serverport
G
Use the 802.1x system switch(config)# 8021x system
server port global
[port ID]
serverport 1815
configuration
command to change
the radious server port
8021x system
G
Use the 802.1x system switch(config)# 8021x system
accountport
account port global
[port ID]
configuration
accountport 1816
command to change
the accounting port
8021x system sharekey
G
Use the 802.1x system switch(config)# 8021x system
share key global
[ID]
sharekey 123456
configuration
command to change
the shared key value.
8021x system nasid
G
Use the 802.1x system switch(config)# 8021x system
nasid global
[words]
nasid test1
configuration
command to change
the NAS ID
8021x misc quietperiod
G
[sec.]
Use the 802.1x misc
switch(config)# 8021x misc
quiet period global
quietperiod 10
configuration
command to specify
the quiet period value
of the switch.
8021x misc txperiod
[sec.]
G
Use the 802.1x misc
switch(config)# 8021x misc
TX period global
txperiod 5
configuration
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
39
command to set the
TX period.
8021x misc
G
supportimeout [sec.]
Use the 802.1x misc
switch(config)# 8021x misc
supp timeout global
supportimeout 20
configuration
command to set the
supplicant timeout.
8021x misc
G
servertimeout [sec.]
Use the 802.1x misc
switch(config)#8021x misc
server timeout global
servertimeout 20
configuration
command to set the
server timeout.
8021x misc maxrequest
G
[number]
Use the 802.1x misc
switch(config)# 8021x misc
max request global
maxrequest 3
configuration
command to set the
MAX requests.
8021x misc
G
reauthperiod [sec.]
Use the 802.1x misc
switch(config)# 8021x misc
reauth period global
reauthperiod 3000
configuration
command to set the
reauth period.
Use the 802.1x port
switch(config)#interface
[disable | reject | accept |
state interface
fastethernet 3
authorize]
configuration
switch(config-if)#8021x portstate
command to set the
accept
8021x portstate
I
state of the selected
port.
show 8021x
E
Displays a summary of switch>show 8021x
the 802.1x properties
and also the port
sates.
no 8021x
G
Disable 802.1x
switch(config)#no 8021x
function
40
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
TFTP Commands Set
Commands
Level Description
backup
G
flash:backup_cfg
Defaults Example
Save configuration to
switch(config)#backup
TFTP and need to
flash:backup_cfg
specify the IP of TFTP
server and the file name
of image.
restore flash:restore_cfg
G
Get configuration from
switch(config)#restore
TFTP server and need to flash:restore_cfg
specify the IP of TFTP
server and the file name
of image.
upgrade
G
flash:upgrade_fw
Upgrade firmware by
switch(config)#upgrade
TFTP and need to
lash:upgrade_fw
specify the IP of TFTP
server and the file name
of image.
SystemLog, SMTP and Event Commands Set
Commands
Level Description
systemlog ip
G
Set System log server switch(config)# systemlog ip
IP address.
[IP address]
systemlog mode
G
Example
192.168.1.100
Specified the log mode switch(config)# systemlog mode
[client|server|both]
both
show systemlog
E
Displays system log.
Switch>show systemlog
show systemlog
P
Show system log client switch#show systemlog
& server information
no systemlog
G
Disable systemlog
switch(config)#no systemlog
functon
smtp enable
G
Enable SMTP function switch(config)#smtp enable
smtp serverip
G
Configure SMTP
switch(config)#smtp serverip
server IP
192.168.1.5
Enable SMTP
switch(config)#smtp
[IP address]
smtp authentication
G
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
41
smtp account
G
authentication
authentication
Configure
switch(config)#smtp account User
authentication account
[account]
smtp password
G
Configure
switch(config)#smtp password
authentication
[password]
password
smtp rcptemail
G
[Index] [Email address]
show smtp
P
Configure Rcpt e-mail switch(config)#smtp rcptemail 1
Address
Alert@test.com
Show the information
switch#show smtp
of SMTP
no smtp
G
Disable SMTP function switch(config)#no smtp
event device-cold-start
G
Set cold start event
switch(config)#event
type
device-cold-start both
Set Authentication
switch(config)#event
failure event type
authentication-failure both
Set X-ring topology
switch(config)#event
changed event type
X-ring-topology-change both
Set port event for
switch(config)#interface
system log
fastethernet 3
[Systemlog|SMTP|Both]
event
G
authentication-failure
[Systemlog|SMTP|Both]
event
G
X-ring-topology-change
[Systemlog|SMTP|Both]
event systemlog
I
[Link-UP|Link-Down|Bot
h]
switch(config-if)#event systemlog
both
event smtp
I
[Link-UP|Link-Down|Bot
Set port event for
switch(config)#interface
SMTP
fastethernet 3
switch(config-if)#event smtp both
h]
show event
P
Show event selection switch#show event
no event
G
Disable cold start
switch(config)#no event
event type
device-cold-start
device-cold-start
no event
G
authentication-failure
no event
G
X-ring-topology-change
Disable Authentication switch(config)#no event
failure event typ
authentication-failure
Disable X-ring
switch(config)#no event
topology changed
X-ring-topology-change
event type
42
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
no event systemlog
I
Disable port event for switch(config)#interface
system log
fastethernet 3
switch(config-if)#no event
systemlog
no event smpt
I
Disable port event for switch(config)#interface
SMTP
fastethernet 3
switch(config-if)#no event smtp
show systemlog
P
Show system log client switch#show systemlog
& server information
SNTP Commands Set
Commands
Level Description
Example
sntp enable
G
Enable SNTP function switch(config)#sntp enable
sntp daylight
G
Enable daylight saving switch(config)#sntp daylight
time, if SNTP function
is inactive, this
command can’t be
applied.
sntp daylight-period
G
[Start time] [End time]
Set period of daylight
switch(config)# sntp
saving time, if SNTP
daylight-period 20060101-01:01
function is inactive,
20060202-01-01
this command can’t be
applied.
Parameter format:
[yyyymmdd-hh:mm]
sntp daylight-offset
G
[Minute]
Set offset of daylight
switch(config)#sntp
saving time, if SNTP
daylight-offset 3
function is inactive,
this command can’t be
applied.
sntp ip
[IP]
G
Set SNTP server IP, if switch(config)#sntp ip 192.169.1.1
SNTP function is
inactive, this command
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
43
can’t be applied.
sntp timezone
G
Set timezone index,
switch(config)#sntp timezone 22
use “show sntp
[Timezone]
timzezone” command
to get more
information of index
number
show sntp
P
Show SNTP
switch#show sntp
information
show sntp timezone
P
Show index number of switch#show sntp timezone
time zone list
no sntp
G
Disable SNTP function switch(config)#no sntp
no sntp daylight
G
Disable daylight saving switch(config)#no sntp daylight
time
X-ring Commands Set
Commands
Level Description
Example
Xring enable
G
Enable X-ring
switch(config)#Xring enable
Xring master
G
Enable ring master
switch(config)#Xring master
Xring couplering
G
Enable couple ring
switch(config)#Xring couplering
Xring dualhoming
G
Enable dual homing
switch(config)#Xring dualhoming
Xring ringport
G
Configure 1st/2nd
switch(config)#Xring ringport 7 8
Ring Port
[1st Ring Port] [2nd Ring
Port]
Xring couplingport
G
[Coupling Port]
Xring controlport
Configure Coupling
switch(config)#Xring couplingport
Port
1
G
Configure Control Port switch(config)#Xring controlport 2
G
Configure Dual
switch(config)#Xring homingport
Homing Port
3
Show the information
switch#show Xring
[Control Port]
Xring homingport
[Dual Homing Port]
show Xring
P
of X - Ring
44
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
no Xring
G
Disable X-ring
switch(config)#no X ring
no Xring master
G
Disable ring master
switch(config)# no Xring master
no Xring couplering
G
Disable couple ring
switch(config)# no Xring
couplering
no Xring dualhoming
G
Disable dual homing
switch(config)# no Xring
dualhoming
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
45
Web-Based Management
About Web-based Management
The switch has an embedded HTML web site residing in flash memory. This
site offers advanced management features and allows the switch to be
configured from anywhere on the network.
The web site is designed for Internet Explorer 6.0 and uses Java Applets to
reduce bandwidth consumption, enhance access speed, and present an
intuitive user interface.
Preparing for Web Management
Before using web management, install the industrial switch on the network
and verify that a PC on the local network can connect with the switch
through the web browser. The default IP Address, Subnet Mask, Username
and Password is listed below:
46
„
IP Address: 192.168.16.1
„
Subnet Mask: 255.255.255.0
„
Default Gateway: 192.168.16.254
„
User Name: root
„
Password: root
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
System Login
1.
Launch Internet Explorer on the PC
2.
Enter “http:// “+” the IP address of the switch”, and then Press “Enter”.
3.
The login screen will appear
4.
Enter user name and password. The default user name and password
are “root”
5.
Press “Enter” or ”OK”
Login screen
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
47
System Information
„
System Name: A name (64 bytes max) can be assigned to the switch.
„
System Description: Displays the description of switch. Read only
cannot be modified
„
System Location: A physical location (64 bytes max) can be assigned
to the switch.
„
System Contact: Enter the name of contact person or organization
„
Firmware Version: Displays the switch’s firmware version
„
Kernel Version: Displays the kernel software version
„
MAC Address: Displays the unique hardware address assigned by
manufacturer (default)
IP Configuration
Configure the IP Settings and DHCP client function
„
DHCP Client: Used to enable or disable the DHCP client function.
When enabled, the switch’s IP address is assigned by the network
DHCP server. The default IP address will be replace by the DHCP
server assigned IP address. After clicking the ‘Apply’ button, a popup
dialog will indicate that the current IP will be lost and the new IP
address must be retrieved from the DHCP server.
„
IP Address: A static IP Address may be assigned. The default IP is
192.168.16.1.
„
Subnet Mask: Assign the subnet mask of the IP address. This does
not have to be done if the DHCP client function is enabled.
„
Gateway: Assign the network gateway. The default gateway is
192.168.16.254.
48
„
DNS1: Assign the primary DNS IP address.
„
DNS2: Assign the secondary DNS IP address.
„
Click
Apply
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
IP configuration interface
DHCP Server – System configuration
The switch can function as a DHCP server.
„
DHCP Server: Enable or Disable the DHCP Server function.
„
Low IP Address: the dynamic IP assign range. Low IP address is the
beginning of the dynamic IP assignment range.
„
High IP Address: the dynamic IP assign range. High IP address is the
end of the dynamic IP assignment range.
„
Subnet Mask: The subnet mask.
„
Gateway:
„
DNS: Network Domain Name Server IP Address.
„
Lease Time (sec): The time interval at which that system will reset the
The network gateway.
dynamic IP assignment.
„
Click
Apply
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
49
DHCP Server Configuration interface
DHCP Client – System Configuration
DHCP client information is displayed.
DHCP Client Entries interface
DHCP Server - Port and IP Bindings
You can assign a specific IP address that is in the dynamic IP assignment
range to the specific port. When the device is connected to the port and
asks for an assignment, the system will assign this IP address.
50
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Port and IP Bindings interface
TFTP - Update Firmware
Provides the ability to update the switch’s firmware. Before updating, ensure
you the TFTP server is ready and the firmware image is on the TFTP server.
1.
TFTP Server IP Address: Enter the TFTP server IP.
2.
Firmware File Name: Enter the name of firmware image.
3.
Click
Apply
.
Update Firmware interface
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
51
TFTP – Restore Configuration
If the EEPROM image is stored on the TFTP server, you can restore it to
flash memory.
1.
TFTP Server IP Address: Enter the TFTP server IP.
2.
Restore File Name: Enter the restore file name.
3.
Click
Apply
.
Restore Configuration interface
TFTP - Backup Configuration
You can save current EEPROM image to the TFTP server.
1.
TFTP Server IP Address: Enter the TFTP server IP
2.
Backup File Name: Enter the file name
3.
Click
Apply
.
Backup Configuration interface
52
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
System Event Log – Syslog Configuration
1.
Syslog Client Mode: select the system log mode – client only, server
only, or both S/C.
2.
System Log Server IP Address: Assign the system log server IP.
3.
Click Reload
to refresh the event log.
4.
Click Clear
to clear all current event log.
5.
After configuring, Click Apply .
Syslog Configuration interface
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
53
System Event Log - SMTP Configuration
Set up the mail server IP, mail account, account password, and email
account for receiving event alerts.
1.
Email Alert: enable or disable the email alert function.
2.
SMTP Server IP: set up the mail server IP address.
3.
Sender: Enter the email address, e.g. switch102@123.com, to identify
where the event log came from.
4.
Authentication: Mark the check box to enable and configure the email
account and password for authentication.
5.
Mail Account: set up the email account, e.g. johnadmin for the switch.
It must be an existing email account on the mail server.
6.
Password: The email account password.
7.
Confirm Password: reconfirm the password.
8.
Rcpt e-mail Address 1 through 6: Enter up to six email addresses to
receive the event log.
9.
Click Apply .
SMTP Configuration interface
54
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
System Event Log - Event Configuration
When the selected events occur, the system will generate a log entry and email
notification message.
System event selection: Four selections available – Cold Start, Warm Start,
SNMP Authentication Failure, and X-ring topology change. Mark the checkbox
to select the event. When the selected events occur, the system will send the
logs.
„
Port event selection: When a port specific event occurs, the system
will generate a log entry and email notification. Three selections are
available – Link UP, Link Down, and Link UP & Link Down.
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
55
Event Configuration interface
Fault Relay Alarm
„
Power Failure: When the check box is marked, the Fault LED will light
if the power source fails.
„
Port Link Down/Broken: When the check box is marked, the Fault
LED will light if a port link goes down.
56
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Fault Relay Alarm interface
SNTP Configuration
SNTP allows you to synchronize switch clocks.
„
SNTP Client: Enables or disables the SNTP function
„
Daylight Saving Time: Enables or disables daylight saving time. When
this function is enabled, the time period must be entered.
„
UTC Time zone: Sets the local time zone.
Local Time Zone
Conversion from UTC
Time at 12:00 UTC
November Time Zone
- 1 hour
11am
Oscar Time Zone
-2 hours
10 am
ADT - Atlantic Daylight
-3 hours
9 am
AST - Atlantic Standard
-4 hours
8 am
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
57
EDT - Eastern Daylight
EST - Eastern Standard
-5 hours
7 am
-6 hours
6 am
-7 hours
5 am
-8 hours
4 am
-9 hours
3 am
-10 hours
2 am
-11 hours
1 am
+1 hour
1 pm
+2 hours
2 pm
+3 hours
3 pm
ZP4 - Russia Zone 3
+4 hours
4 pm
ZP5 – Russia Zone 4
+5 hours
5 pm
ZP6 - RUSSIA Zone 5
+6 hours
6 pm
+7 hours
7 pm
CDT - Central Daylight
CST - Central Standard
MDT - Mountain Daylight
MST - Mountain
Standard
PDT - Pacific Daylight
PST - Pacific Standard
ADT - Alaskan Daylight
ALA - Alaskan Standard
HAW - Hawaiian
Standard
Nome, Alaska
CET - Central European
FWT - French Winter
MET - Middle European
MEWT - Middle
European Winter
SWT - Swedish Winter
EET - Eastern European,
Russia Zone 1
BT - Baghdad, Russia
Zone 2
WAST - West Australian
Standard
58
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
CCT - China Coast,
RUSSIA Zone 7
JST - Japan Standard,
RUSSIA Zone 8
+8 hours
8 pm
+9 hours
9 pm
+10 hours
10 pm
+12 hours
Midnight
EAST - East Australian
Standard GST
Guam Standard,
RUSSIA Zone 9
IDLE - International Date
Line
NZST - New Zealand
Standard
NZT - New Zealand
„
SNTP Sever URL: Enter the SNTP server IP address.
„
Daylight Saving Period: Enter the Daylight Saving beginning time and
Daylight Saving end time.
„
Daylight Saving Offset (mins): Enter the offset in minutes.
„
Switch Timer: Displays the current time.
„
Click
Apply
.
SNTP Configuration interface
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
59
IP Security
IP security function grants 10 specific IP addresses permission to access
the switch through a web browser or TELNET for management.
„
IP Security Mode: When enabled, allows management via TELNET
and HTTP.
„
Enable HTTP Server: Mark the box to grant the specified IP addresses
web based management permission.
„
Enable Telnet Server: Mark the box to grant the specified IP
addresses TELNET management permission.
„
Security IP 1 ~ 10: Enter up to 10 IP addresses.
„
And then, click
Apply
button to apply the configuration
[NOTE] If the configuration is not saved, it will be lost when the switch is
powered down.
IP Security interface
60
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
User Authentication
Use this function to change the login name and password.
1.
User name: Enter the new user name (The default is ‘root’).
2.
Password: Enter the new password (The default is ‘root’).
3.
Confirm password: Confirm the new password.
4.
And then, click Apply
User Authentication interface
Port Statistics
„
Port: The port number.
„
Type: Displays the connection speed.
„
Link: Displays link status —‘Up’ or ‘Down’.
„
State: Enabled or Disabled.
„
Tx Good Packet: Displays the number of good packets transmitted.
„
Tx Bad Packet: Displays the number of bad packets transmitted.
„
Rx Good Packet: Displays the number of good packets received.
„
Rx Bad Packet: Displays the number of bad packets received.
„
Tx Abort Packet: Displays the number of aborted transmit packets.
„
Packet Collision: Displays the number of packet collisions.
„
Packet Dropped: Displays the number of dropped packets.
„
Rx Bcast Packet: Displays the number of broadcast packets.
„
Rx Mcast Packet: Displays the number of multicast packets.
„
Click
Clear
button to clean all counts.
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
61
Port Statistics interface
Port Control
Used to configure and view port settings.
1.
Port: Select the port to configure.
2.
State: Enable or disable the port.
3.
Negotiation: Set the negotiation status of the port.
4.
Speed: Set the port link speed.
5.
Duplex: Set the port to full or half-duplex.
6.
Flow Control: Set flow control to Symmetric or Asymmetric in Full
Duplex mode. The default value is Symmetric.
7.
Security: Set the port security. When ‘On’ is selected, the port will only
accept a connection from one MAC address.
8.
62
Click
Apply
.
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Port Control interface
Port Trunk
The Link Aggregation Control Protocol (LACP) provides a standardized
method for exchanging information between Partner Systems on a link. This
allows their Link Aggregation Control instances to reach an agreement on
the identity of the Link Aggregation Group, move the link to that Link
Aggregation Group, and enable its transmission and reception functions in
an orderly manner. Link aggregation lets you group up to four consecutive
ports into two dedicated connections. This feature expands bandwidth to a
device on the network. LACP operation requires full-duplex mode.
Aggregator setting
1.
System Priority: a value used to identify the active LACP. The switch
with the lowest value has the highest priority. It is selected as the active
LACP.
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
63
2.
Group ID: There are three trunk groups to configure. Choose the
"Group ID" and click Select .
3.
LACP: If enabled, the group is an LACP static trunk group. If disabled,
the group is local static trunk group. All ports support LACP dynamic
trunk. If connected to a device that also supports LACP, the LACP
dynamic trunk group is automatically created.
4.
Work ports: A maximum of four ports can be aggregated at the same
time. With LACP static trunk group, any excess ports are considered
standby and can be aggregated if a work port fails. If it is local static
trunk group, the number of ports must be the same as the group
member ports.
5.
Select the ports to add to the trunk group. Click
Add
button to add
the port. To remove unwanted ports, select the port and click Remove
button.
6.
When LACP is enabled, you can configure LACP Active/Passive status
for each port on the State Activity page.
7.
Click
8.
Use Delete button to delete Trunk Group. Select the Group ID and
Apply
click Delete button.
64
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Port Trunk—Aggregator Setting interface
Aggregator Information
Displays static trunk group information.
Port Trunk – Aggregator Information interface
State Activity
When you had setup the LACP aggregator, port state activity can be
configured. Mark port click
Apply
. The port state activity will change to
Active or Passive depending on its previous state.
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
65
„
Active: The port automatically sends LACP protocol packets.
„
Passive: The port responds only if it receives LACP protocol packets
from the opposite device.
[NOTE]
1. A link having either two active LACP ports or one active port can
perform dynamic LACP trunk.
2. A link, which has two passive LACP ports, will not perform dynamic
LACP trunk because both ports are waiting for an LACP protocol
packet from the opposite device.
Port Trunk – State Activity interface
Port Mirroring
Port mirroring is a method to monitor traffic in switched networks. Traffic
flowing through the indicated ports can be monitored by a specified port.
„
Destination Port: Only one port can be selected as the destination
(mirror) port for monitoring both RX and TX traffic from the source port.
Two ports may be configured to monitor RX and TX traffic separately. A
LAN analyzer can be connected to the mirror port.
„
Source Port: Select the ports to monitor. All monitored port traffic will
be sent to the mirror (destination) port. Multiple source ports by can be
selected by checking the RX or TX check boxes.
„
66
Click
Apply
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Port Trunk – Port Mirroring interface
Rate Limiting
Set up each port’s bandwidth rate and frame limitation type.
„
Ingress Limit Frame type: Select the frame type to filter. There are
four options: All, Broadcast/Multicast/Flooded Unicast,
Broadcast/Multicast and Broadcast only.
„
Egress Limit: The egress rate limit is ALL.
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
67
Rate Limiting interface
„
All the ports support port ingress and egress rate control. For example,
assume port 1 is 10Mbps, users can set its effective egress rate to
1Mbps, and ingress rate is 500Kbps. The switch performs the ingress
rate limiting using a packet counter to meet the specified rate
¾
Ingress: Enter the port effective ingress rate(The default value is
‘0’)
„
Egress: Enter the port effective egress rate(The default value is ‘0’)
„
Click
Apply
VLAN configuration
A Virtual LAN (VLAN) can be thought of as a broadcast domain that exists
within a switch or a defined set of switches. By grouping switch ports into
VLANs, traffic flooding is limited since devices can only communicate
directly with devices belonging to the VLAN. Creating a VLAN from a switch
is the logical equivalent of reconnecting a group of devices to another Layer
2 switch. However, the network devices retain their same physical
connection. The switch supports port-based and 802.1Q (tagged-based)
VLAN. In the default configuration, the VLAN option is disabled.
68
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
VLAN Configuration interface
VLAN configuration - Port-based VLAN
With port-based VLAN, the port is assigned to a VLAN. Therefore, all
devices attached to a given port should be members of the same VLAN. As
with other VLAN configurations, the packets forwarded using this method do
not leak into other VLAN domains on the network. After the port has been
assigned to a VLAN, devices on the port cannot send to or receive from
devices in other VLANs without the intervention of another layer 3 device or
the ability to tag the data packet with a specific PVID.
VLAN – Port Based interface
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
69
„
Click Add to add a new VLAN group (The maximum number of VLAN
groups is 64)
„
Enter the VLAN name, group ID, the members of the VLAN group
„
Click
Apply
VLAN—Port Based Add interface
„
The VLAN is displayed.
„
Use
„
Use Edit
Delete
button to delete an unwanted VLAN.
button to modify an existing VLAN group.
[NOTE] If the configuration is not saved, it will be lost when the switch is
powered down.
70
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
802.1Q VLAN
Tagged-based VLAN is an IEEE 802.1Q specification, which allows VLANs
to be created across devices from different venders. IEEE 802.1Q VLAN
uses a technique to insert a “tag” into the Ethernet frame. The tag contains a
VLAN Identifier (VID).
When the 802.1Q VLAN is enabled, all ports on the switch belong to a
default VLAN (VID 1). The default VLAN cannot be deleted. Up to 64 VLAN
groups are supported.
802.1q VLAN interface
802.1Q Configuration
1.
Enable GVRP Protocol: check the check box to enable GVRP
protocol.
2.
Select the port to configure.
3.
Link Type: there are three link types.
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
71
„
Access Link: Single switch only. Allows ports to be grouped by
setting the same VID.
„
Trunk Link: Extended application of Access Link. Allows ports to
be grouped by setting the same VID on two or more switches.
„
Hybrid Link: Both Access Link and Trunk Link.
4.
Untagged VID: assign the untagged frame VID.
5.
Tagged VID: assign the tagged frame VID.
6.
Click
Apply
Group Configuration
Edit the existing VLAN Group.
1.
Select the VLAN group in the table list.
2.
Click
Apply
Group Configuration interface
72
3.
You can Change the VLAN group name and VLAN ID.
4.
Click
Apply
.
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Group Configuration interface
Rapid Spanning Tree
The Rapid Spanning Tree Protocol (RSTP) is an evolution of Spanning Tree
Protocol (STP). It provides a faster spanning tree convergence after a
topology change. The switch will auto detect a device that is running STP or
RSTP protocol.
RSTP System Configuration
„
RSTP state can be modified. After modification, click Apply
¾
RSTP mode: Enable or disable the RSTP.
¾
Priority (0-61440): a value used to identify the root bridge. The
bridge with the lowest value has the highest priority and is selected
as the root. If the value changes, the switch must be rebooted. The
value must be multiple of 4096.
¾
Max Age (6-40): The number of seconds a bridge waits without
receiving Spanning-tree Protocol configuration messages before
attempting a reconfiguration. Enter a value between 6 through 40
¾
Hello Time (1-10): The time that controls when, the switch sends
out the BPDU packet to check RSTP status. Enter a value between
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
73
1 and 10.
¾
Forward Delay Time (4-30): the number of seconds a port waits
before changing from its Rapid Spanning Tree Protocol learning
and listening state to the forwarding state. Enter a value between 4
and 30.
[NOTE]
1. Use the following rule to configure the MAX Age, Hello Time, and
forward Delay Time
2 x (Forward Delay Time value –1) > = Max Age value >= 2 x (Hello
Time value +1)
2. If the configuration is not saved, it will be lost when the switch is
powered down.
RSTP System Configuration interface
74
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
RSTP Port Configuration
Configure path cost and priority of each port.
1. Select the port in Port column.
1. Path Cost: The cost of the path to the other bridge from this transmitting
bridge at the specified port. Enter a number 1 through 200000000.
2. Priority: Network priority. Enter a number between 0 and 240. The value
must be a multiple of 16.
3. P2P: Some of the rapid state transactions that are possible within RSTP
are dependent upon whether the port concerned can only be connected
to exactly one other bridge (i.e. it is served by a point-to-point LAN
segment), or can be connected to two or more bridges (i.e. it is served
by a shared medium LAN segment). This function allows the P2P status
of the link to be manipulated administratively. True is P2P enabled.
False is P2P disabled.
4. Edge: The port directly connected to the end stations cannot create a
bridging loop in the network. To configure the port as an edge port, set
the port to ‘True’ status.
5. Non STP: Set True to disable STP mathematic calculation. Set False to
including the STP mathematic calculation.
6. Click
Apply
.
RSTP Per Port Configuration interface
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
75
SNMP Configuration
Simple Network Management Protocol (SNMP) is the protocol developed to
manage nodes (servers, workstations, routers, switches, hubs, etc.) on an
IP network. SNMP enables network administrators to manage network
performance, find and solve network problems, and plan for network growth.
Network management systems learn of problems by receiving traps or
change notices from network devices implementing SNMP
System Configuration
„
Community Strings
Define and remove community strings.
1.
String: Enter the name of the string.
2.
RO: Read only. Enables requests accompanied by this string to display
MIB-object information.
3.
RW: Read write. Enables requests accompanied by this string to
display MIB-object information and to set MIB objects.
4.
Click Add .
5.
To remove the community string, select the community string and click
Remove
„
. You cannot remove the default community string set.
Agent Mode: Select the SNMP version that you want to use and click
Change
76
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
SNMP System Configuration interface
Trap Configuration
A trap manager is a management station that receives traps (the system
alerts generated by the switch). If the trap manager is not defined, traps will
not be issued. Create a trap manager by entering the IP address of the
station and a community string.
1. IP Address: Enter the IP address of the trap manager.
2. Community: Enter the community string.
3. Trap Version: Select the SNMP trap version type (v1 or v2c).
4. Click Add
5. To remove the community string, select the community and click
Remove
. You cannot remove the default community string.
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
77
Trap Managers interface
SNMPV3 Configuration
Configure the SNMP V3 function.
Context Table
Configure SNMP v3 context table. Assign the context name of context table.
Click Add
to add context name. Click
Remove
to remove an unwanted
context name.
User Profile
Configure SNMP v3 user table.
„
User ID: Enter user name.
„
Authentication Password: Enter the password.
„
Privacy Password: Enter the private password.
„
Click
Click
78
Add
Remove
to add context name.
to remove an unwanted context name.
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
SNMP V3 configuration interface
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
79
Group Table
Configure SNMP v3 group table.
„
Security Name (User ID): assign the user name that was set up in
user table.
„
Group Name: Enter the group name.
„
Click
„
Click
Add
Remove
to remove unwanted context name.
Access Table
Configure SNMP v3 access table.
„
Context Prefix: set up the context name.
„
Group Name: set up the group.
„
Security Level: select the access level.
„
Context Match Rule: select the context match rule.
„
Read View Name: set up the read view.
„
Write View Name: set up the write view.
„
Notify View Name: set up the notify view.
„
Click
„
Click
Add
to add context name.
Remove
to remove unwanted context name.
MIBview Table
Configure MIB view table.
80
„
ViewName: set up the name.
„
Sub-Oid Tree: fill the Sub OID.
„
Type: select the type – exclude or included.
„
Click
„
Click
Add
to add context name.
Remove
to remove unwanted context name.
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
QoS Configuration
QoS Policy and Priority Type
„
QoS Policy: select the QoS policy rule.
¾
Use an 8,4,2,1 weighted fair queuing scheme: The switch will
follow 8:4:2:1 rate to process the priority queue from the highest to
the lowest queue. For example, when processing, 1 frame of the
lowest queue, 2 frames of the low queue, 4 frames of the middle
queue, and 8 frames of the high queue will be processed at the
same time.
¾
Use the strict priority scheme: The highest queue will always
processed first.
„
Priority Type: there are five priority selections available.
„
Port-base: the port priority will follow the assigned Port-base – High,
middle, low, or lowest.
¾
COS Only: the port priority will only follow the COS priority
assigned.
¾
TOS only: the port priority will only follow the TOS priority
assigned.
¾
COS first: the port priority will follow the COS priority first, and
then the other priority rule.
¾
TOS first: the port priority will follow the TOS priority first, and then
the other priority rule.
„
Click
Apply
.
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
81
QoS Configuration interface
82
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Port Base Priority
Configure per port priority level.
„
Port 1 through 10: 4 priority levels – High, Middle, Low, and Lowest.
„
Click
Apply
COS Configuration
Set up the COS priority level.
„
COS priority: Set up the COS priority level 0~7 –High, Middle, Low,
Lowest.
„
Click Apply .
TOS Configuration
„
TOS priority: the system provides 0 to 63 TOS priority levels. Each
level has four types of priority – high, middle, low, and lowest. The default
value is ‘Lowest’. When an IP packet is received, the system will check the
TOS level value in the IP packet. For example, if the TOS level 25 is high
and the port is following the TOS priority policy only, when a packet is
received, the system will check the TOS value of the received IP packet. If
the TOS value of received IP packet is 25(priority = high), then the packet
will have highest priority.
„
Click
Apply
.
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
83
IGMP Configuration
The Internet Group Management Protocol (IGMP) is an internal protocol of
the Internet Protocol (IP) suite. IP manages multicast traffic by using
switches, routers, and hosts that support IGMP. Enabling IGMP allows the
ports to detect IGMP queries and report packets and manage IP multicast
traffic through the switch. IGMP has three fundamental types of message.
Message
Description
A message sent from the querier (IGMP router or switch)
asking for a response from each host belonging to the
multicast group.
Query
A message sent by a host to the querier to indicate that the
host wants to be or is a member of a given group indicated in
Report
the report message.
Leave
A message sent by a host to the querier to indicate that the
Group
host has quit being a member of a specific multicast group.
The switch support IP multicast, you can enable IGMP protocol on web
management’s switch setting advanced page, then the IGMP snooping
information displays. IP multicast addresses range are from 224.0.0.0
through 239.255.255.255.
„
IGMP Protocol: Enable or disable the IGMP protocol.
„
IGMP Query: Enable or disable the IGMP query function. The IGMP
query information will be displayed in IGMP status section.
„
84
Click
Apply
.
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
IGMP Configuration interface
X-Ring
X-Ring provides network redundancy similar to the Spanning Tree and
Rapid Spanning Tree Protocols. However, recovery time is greatly reduced
when the X-Ring protocol is used. The protocol identifies one switch as the
Ring Master. Packets are blocked from the redundant path unless a ring
member becomes disconnected from the rest of the network. When this
happens, the protocol automatically restores connectivity using the
redundant path.
In the X-Ring topology, every switch should enable X-Ring function and
assign two member ports to the ring. Only one switch in the X-Ring group
would be set as the backup switch. Other switches are called working
switches and their two member ports are called working ports. If a network
connection failure occurs, the backup port will automatically become a
working port to recover.
The switch can be set in the ring master or slave mode. The ring master
negotiates and places commands to the other switches in the X-Ring group.
If there are two or more switches in the master mode, the software will
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
85
select the switch with lowest MAC address number as the ring master. The
X-Ring master mode is enabled using the X-Ring configuration interface.
The Ring Master can also be identified using the R.M. LED on the front of
the switch.
The switch also supports coupling ring to connect two or more X-Ring
groups for redundant backup. The dual homing function is used to prevent a
connection lose between the X-Ring group and the upper level/core switch.
„
Enable X-Ring: Mark the check box to enable the X-Ring function.
„
Enable Ring Master: Mark the check box to set the switch as the Ring
Master.
„
1st & 2nd Ring Ports: Assign two ports as the member ports. 1st Ring
Port is the working port and 2nd Ring Port is the backup port. When 1st
Ring Port fails, the system will automatically upgrade the 2nd Ring
Port to be the working port.
„
Enable Coupling Ring: Mark the check box to enable the coupling ring
function.
„
Coupling port: Assign the member port.
„
Control port: Set the switch as the master switch in the coupling ring.
„
Enable Dual Homing: Set up one of port on the switch to be the Dual
Homing port. In an X-Ring group, only one port can be the Dual Homing
port. Dual Homing only works when the X-Ring function is enabled.
„
And then, click Apply
to apply the configuration.
X ring Interface
86
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
[NOTE]
1. When X-Ring function is enabled, disable the RSTP function. X-Ring
and RSTP cannot exist at the same time.
2. If the configuration is not saved, it will be lost when the switch is powered
down.
„ Security
In this section, you can configure 802.1x and MAC address table.
802.1X/Radius Configuration
802.1x is an IEEE authentication specification that allows a client to connect
to a wireless access point or wired switch but prevents the client from
gaining access to the Internet until it proves authority by providing a user
name and password, which is verified by a separate server.
System Configuration
1.
IEEE 802.1x Protocol: Enable or disable 802.1x protocol.
2.
Radius Server IP: Enter the Radius Server IP address.
3.
Server Port: Enter the UDP destination port for authentication requests
to the Radius Server.
4.
Accounting Port: Enter the UDP destination port for accounting
requests to the Radius Server.
5.
Shared Key: Enter an encryption key for use during authentication
sessions. This key must match the encryption key used on the Radius
Server.
6.
NAS, Identifier: Enter the identifier of the radius client.
7.
Click
Apply
.
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
87
802.1x System Configuration interface
802.1x Per Port Configuration
You can configure 802.1x authentication state for each port. The State
choices are Disable, Accept, Reject and Authorize. Use the ‘Space’ key
change the state value.
„
Reject: The port is held in the unauthorized state.
„
Accept: The port is held in the Authorized state.
„
Authorized: The port will allow an authentication exchange between
the supplicant and the authentication server.
88
„
Disable: The port is held in the Authorized state
„
Click
Apply
.
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
802.1x Per Port Setting interface
Misc Configuration
1.
Quiet Period: Sets the period during which the port does not try to
acquire a supplicant.
2.
TX Period: Sets the period that the port waits before retransmitting the
next EAPOL PDU during an authentication session.
3.
Supplicant Timeout: Sets the period the switch waits for a supplicant
response to an EAP request.
4.
Server Timeout: Set the period the switch waits for a server response
to an authentication request.
5.
Max Requests: Sets the number of authentications that time-out
before authentication fails and the authentication session ends.
6.
Reauth period: Set the period of time after which connected clients
must be re-authenticated.
7.
Click
Apply
.
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
89
802.1x Misc Configuration interface
MAC Address Table
Static MAC Address
You can add a static MAC address. This address remains in the switch's
address table, regardless of whether the device is physically connected to
the switch. Therefore, the switch does not have to re-learn a device's MAC
address when the disconnected or powered-off device reconnects to the
network. You can add / modify / delete a static MAC address.
„
Add the Static MAC Address
You can add static MAC addresses in the MAC table.
1.
MAC Address: Enter the MAC address of the port that should
permanently forward traffic, regardless of the device network activity..
.
2.
Click
3.
If you want to delete a MAC address from filtering table, select it click
Add
Delete
90
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Static MAC Addresses interface
MAC Filtering
MAC Filtering interface
1.
MAC Address: Enter the MAC address that you want to filter.
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
91
2.
Click
3.
If you want to delete the MAC address from filtering table, select the
Add
.
MAC address and click
Delete
.
All MAC Addresses
1.
Select the port.
2.
The selected port of static MAC address information will be displayed.
3.
Click
Clear MAC Table
to clear the current port static MAC address
information on screen.
All MAC Address interface
Factory Default
To reset switch to default configuration, with an option to retain the current
IP address and user name/password click
92
Default
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Factory Default interface
Save Configuration
Save configuration changes click
Save Flash
Save Configuration interface
System Reboot
Reboot the switch click
Reboot
System Reboot interface
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
93
Trouble shooting
„
„
Verify that 24 to 48VDC power is available. Do not exceed 48VDC.
Select the proper cable to construct your network. Use unshielded
twisted-pair (UTP) or shield twisted-pair (STP) cable for RJ-45 connections
100Ω Category 3, 4, or 5 cable for 10Mbps connections, 100Ω Category 5
cable for 100Mbps, or 100Ω Category 5e/above cable for 1000Mbps
connections. Ensure that the length of any twisted-pair connection does not
exceed 100 meters (328 feet).
„
94
LED Indicators: The LEDs can be used to diagnose system problems
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Technical Specification
The 8 10/100TX plus 2 100FX managed industrial switch technical
specification is following.
IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 100Base-TX and 100Base-FX Fast Ethernet
IEEE802.3x Flow Control and Back Pressure
IEEE802.3ad Port trunk with LACP
Standard
IEEE802.1d Spanning Tree/ IEEE802.1w Rapid Spanning Tree
IEEE802.1p Class of Service
IEEE802.1Q VLAN Tag
IEEE 802.1x User Authentication (Radius)
CSMA/CD
Protocol
SNMP v1, v2c, v3 management
Web interface management
Management
Telnet interface management
Command Line Interface(CLI) management
Menu Driven interface management
RFC2030 SNTP, RFC 2821 SMTP, RFC 1215 Trap,
RFC Standard
RFC2233 MIBII, RFC 1157 SNMP MIB, RFC 1493 Bridge
MIB, RFC 2674 VLAN MIB, RFC 2665 Ethernet like MIB, RFC
2819 RMON MIB, Private MIB
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
95
Up to 3 Trap stations
Cold start, Port link up,
Port link down,
Authentication Failure,
SNMP Trap
Private Trap for power status,
Port Alarm configuration,
Fault alarm,
X-ring topology change
Technology
Transfer Rate
Store and forward switching architecture
14,880 pps for 10Base-T Ethernet port
148,800 pps for 100Base-TX/FX Fast Ethernet port
4 types of packet filter rule with different packet combination:
„ All of packet
Packet filter
„ Broadcast/ multicast/ flooded unicast packet
„ Broadcast/ multicast packet
„ Broadcast packet only
MAC address
8K MAC address table
Packet Buffer
1Mbits
RJ-45 port: Link/Activity (Green), Full duplex/Collision
(Orange)
Fiber port: Link/Activity (Green)
LED
Per unit: Power (Green), Power 1 (Green), Power 2 (Green),
Fault (Orange), Master (Green)
10Base-T: 2-pair UTP/STP Cat. 3, 4, 5 cable
Network Cable
EIA/TIA-568 100-ohm (100m)
100Base-TX: 2-pair UTP/STP Cat. 5 cable
EIA/TIA-568 100-ohm (100m)
96
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
Optical cable
„
SC (Multi-mode): 50/125um or 62.5/125um
„
SC (Single mode): 9/125um
„
Available distance: 2KM (Multi-mode) / 30KM
(single-mode)
„
Back-plane
Packet throughput
ability
Wavelength: 1310nm (multi-mode/ single mode)
2.0 Gbps
2.976Mpps at @64bytes
24 ~48 VDC
Power Supply
Redundant power with polarity reverse protects function and
removable terminal block.
Power
consumption
11.28 Watts
2 ports for X-Ring to provide redundant backup feature and the
recovery time below 300ms and start by Web interface
X-Ring
management. The ring port can be defined by Web interface.
Port based VLAN
IEEE802.1Q Tag VLAN.
VLAN
Both of port based and Tag based VLAN group up to 256
VLANs.
Port Trunk with
LACP
Class of service
Quality of service
Spanning tree
LACP Port Trunk: 4 Trunk groups/Maximum 4 trunk members
IEEE802.1p class of service
Per port provides 4 priority queues.
Port based/Tag based, IPv4 ToS, IPv4 Different Service.
IEEE802.1d spanning tree
IEEE802.1w rapid spanning tree.
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
97
IGMP v1, v2 and Query mode
IGMP
Up to 256 multicast groups.
Support SMTP Server and 6 e-mail accounts for receiving
SMTP
event alert
Support SNTP to synchronize system clock in Internet
SNTP
Management IP
IP address security to prevents unauthorized intruder
security
TX packet only
RX packet only
Port mirror
Both of TX and RX packet
Firmware update
TFTP firmware update
TFTP backup and restore
Relay output for port breakdown and power source failure.
Alarm Relay Contact Rating: 1A @ 24VDC
Relay Alarm
Contacts normally open
„
Ingress packets filter and egress packet limit.
„
The egress rate control supports all of packet type and
the limit rate range is from 100 kbps to 102400 kbps or
256000 kbps for giga ports.
Bandwidth control
„
Ingress filter packet type combination rule for
Broadcast/Multicast/Flooded Unicast packet,
Broadcast/Multicast packet, Broadcast packet only and
all of packet.
„
The ingress packet filter rate range is from 100 kbps to
102400 kbps or 256000 kbps for giga ports.
DHCP client
98
DHCP client function to obtain IP address from DHCP serve
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
DIN rail kit and wall mount ear for wall mount or DIN-type
Install
cabinet install
Operating Temp.
Operating
Humidity
Storage
-40℃ to 75℃
5% to 95% (Non-condensing)
-40℃ to 85℃
Temperature
Case
IP30
Dimensions
2.7 x 4.2 x 6.4 in (7.4 x 10.7 x 16.13 cm)
FCC Class A
CE EN61000-4-2
CE EN61000-4-3
CE EN61000-4-4
CE EN61000-4-5
EMI
CE EN61000-4-6
CE EN61000-4-8
CE EN61000-4-11
CE EN61000-4-12
UL
Safety
cUL
CE/EN60950-1
IEC60068-2-32 (Free fall)
Stability testing
IEC60068-2-27 (Shock)
IEC60068-2-6 (Vibration)
Manual Documentation Number: EIR510-xSFP-T_0708m
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com
99