Behringer EURODESK Music Mixer User Manual

User Manual
EURODESK
SX2442FX/SX3242FX
Ultra-Low Noise Design 24/32-Input 4-Bus
Studio/Live Mixer with XENYX Mic Preamplifiers,
British EQs and Dual Multi-FX Processor
behringer.com
2
EURODESK SX2442FX/SX3242FX User Manual
Table of Contents
Thank you........................................................................ 2
Important Safety Instructions....................................... 3
Legal Disclaimer.............................................................. 3
Limited Warranty............................................................ 3
1. Introduction................................................................ 5
1.1 Before you get started....................................................... 5
1.2 The manual............................................................................ 5
2. Control Elements and Connections.......................... 6
2.1 Mono input channels......................................................... 6
2.2 Stereo channels.................................................................... 7
2.3 Stereo channels 21-24 (SX2442FX) or
29-32 (SX3242FX)......................................................................... 8
2.4 Subgroups 1-4...................................................................... 8
2.5 Mono out section for subwoofer applications......... 9
2.6 Main out section.................................................................. 9
2.7 CD/tape................................................................................. 10
2.8 Master Aux Send 1 and 2................................................ 10
2.9 Graphic 9-band stereo equalizer................................. 11
2.10 Effects section................................................................... 11
2.11 Rear panel........................................................................... 12
3. Digital Effects Processor.......................................... 12
4. Wiring Examples....................................................... 13
4.1 Studio set-up....................................................................... 13
4.2 Live set-up............................................................................ 14
5. Audio Connectors..................................................... 15
6. Presets....................................................................... 17
7. Specifications............................................................ 18
Thank you
Congratulations! With the EURODESK you have acquired a state-of-the-art mixing
console that sets new standards. Right from the very start it has been our goal to
design a revolutionary unit that can be used for a great variety of applications.
And indeed, this overwhelming mixing console gives you plenty of functionality
and a broad range of connection and expansion options.
BEHRINGER is a company with its roots in professional recording studio
technology. For many years now we have been successful in developing products
for studio and live use. These include microphones and studio gear of all kinds
(compressors, enhancers, noise gates, tube processors, headphone amplifiers,
digital effects, DI boxes, etc.), monitor and P.A. speakers as well as professional
live and recording mixers. Our entire technical know-how has gone into your
EURODESK mixing console.
behringer.com
3
EURODESK SX2442FX/SX3242FX User Manual
Important Safety
Instructions
Terminals marked with this symbol carry
electrical current of sufficient magnitude to
constitute risk of electric shock. Use only
high-quality commercially-available speaker cables with
¼" TS plugs pre-installed. All other installation or
modification should be performed only by
qualified personnel.
9. Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding-type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11. Use only attachments/accessories specified by
the manufacturer.
12. Use only with the
cart, stand, tripod, bracket,
or table specified by the
manufacturer, or sold with
the apparatus. When a cart
is used, use caution when
moving the cart/apparatus
combination to avoid
This symbol, wherever it appears, alerts you
to the presence of uninsulated dangerous
voltage inside the enclosure - voltage that
may be sufficient to constitute a risk of shock.
This symbol, wherever it appears, alerts you
to important operating and maintenance
instructions in the accompanying literature.
Please read the manual.
Caution
To reduce the risk of electric shock, do not
remove the top cover (or the rear section).
No user serviceable parts inside. Refer servicing to
qualified personnel.
Caution
To reduce the risk of fire or electric shock,
do not expose this appliance to rain and
moisture. The apparatus shall not be exposed to dripping
or splashing liquids and no objects filled with liquids, such
as vases, shall be placed on the apparatus.
injury from tip-over.
13. Unplug this apparatus during lightning storms or
when unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power supply cord or plug
is damaged, liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been exposed
to rain or moisture, does not operate normally, or has
been dropped.
15. The apparatus shall be connected to a MAINS socket
outlet with a protective earthing connection.
16. Where the MAINS plug or an appliance coupler is
used as the disconnect device, the disconnect device shall
remain readily operable.
Caution
These service instructions are for use
by qualified service personnel only.
To reduce the risk of electric shock do not perform any
servicing other than that contained in the operation
instructions. Repairs have to be performed by qualified
service personnel.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
Limit
§ 1 Warranty
[1] This limited warranty is valid only if you purchased
the product from a BEHRINGER authorized dealer in the
country of purchase. A list of authorized dealers can be
found on BEHRINGER’s website behringer.com under
“Where to Buy“, or you can contact the BEHRINGER office
closest to you.
[2] MUSIC Group* warrants the mechanical and
electronic components of this product to be free of defects
in material and workmanship if used under normal
operating conditions for a period of one (1) year from
the original date of purchase (see the Limited Warranty
terms in § 4 below), unless a longer minimum warranty
period is mandated by applicable local laws. If the product
shows any defects within the specified warranty period
and that defect is not excluded under § 4, MUSIC Group
shall, at its discretion, either replace or repair the product
using suitable new or reconditioned product or parts.
In case MUSIC Group decides to replace the entire product,
this limited warranty shall apply to the replacement
product for the remaining initial warranty period, i.e.,
one (1) year (or otherwise applicable minimum warranty
period) from the date of purchase of the original product.
[3] Upon validation of the warranty claim, the repaired
or replacement product will be returned to the user freight
prepaid by MUSIC Group.
[4] Warranty claims other than those indicated above
are expressly excluded.
PLEASE RETAIN YOUR SALES RECEIPT. IT IS YOUR PROOF
OF PURCHASE COVERING YOUR LIMITED WARRANTY.
THIS LIMITED WARRANTY IS VOID WITHOUT SUCH PROOF
OF PURCHASE.
§ 2 Online registration
Please do remember to register your new BEHRINGER
equipment right after your purchase at behringer.com
under “Support” and kindly read the terms and conditions
of our limited warranty carefully. Registering your
purchase and equipment with us helps us process
your repair claims quicker and more efficiently.
Thank you for your cooperation!
§ 3 Return materials authorization
Legal Disclaimer
Technical specifications and appearance are subject to change without
notice. The information contained herein is correct at the time of printing.
All trademarks are the property of their respective owners. MUSIC Group
accepts no liability for any loss which may be suffered by any person
who relies either wholly or in part upon any description, photograph or
statement contained herein. Colors and specifications may vary slightly from
product. BEHRINGER products are sold through authorized dealers only.
Distributors and dealers are not agents of MUSIC Group and have absolutely
no authority to bind MUSIC Group by any express or implied undertaking
or representation. This manual is copyrighted. No part of this manual may
be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying and recording of any kind, for any
purpose, without the express written permission of Red Chip Company Ltd.
ALL RIGHTS RESERVED.
© 2010 Red Chip Company Ltd.
Trident Chambers, Wickhams Cay, P.O. Box 146,
Road Town, Tortola, British Virgin Islands
behringer.com
Limited Warranty
[1] To obtain warranty service, please contact the
retailer from whom the equipment was purchased.
Should your BEHRINGER dealer not be located in your
vicinity, you may contact the BEHRINGER distributor for
your country listed under “Support” at behringer.com.
If your country is not listed, please check if your problem
can be dealt with by our “Online Support” which may
also be found under “Support” at behringer.com.
Alternatively, please submit an online warranty claim at
behringer.com BEFORE returning the product. All inquiries
must be accompanied by a description of the problem
and the serial number of the product. After verifying
the product’s warranty eligibility with the original sales
receipt, MUSIC Group will then issue a Return Materials
Authorization (“RMA”) number.
Lega
4
EURODESK SX2442FX/SX3242FX User Manual
[2] Subsequently, the product must be returned in
its original shipping carton, together with the return
authorization number to the address indicated by
MUSIC Group.
[3] Shipments without freight prepaid will not
be accepted.
§ 4 Warranty Exclusions
[1] This limited warranty does not cover consumable
parts including, but not limited to, fuses and batteries.
Where applicable, MUSIC Group warrants the valves or
meters contained in the product to be free from defects in
material and workmanship for a period of ninety (90) days
from date of purchase.
[2] This limited warranty does not cover the product
if it has been electronically or mechanically modified
in any way. If the product needs to be modified or
adapted in order to comply with applicable technical
or safety standards on a national or local level, in any
country which is not the country for which the product
was originally developed and manufactured, this
modification/adaptation shall not be considered a defect
in materials or workmanship. This limited warranty does
not cover any such modification/adaptation, regardless
of whether it was carried out properly or not. Under the
terms of this limited warranty, MUSIC Group shall not
be held responsible for any cost resulting from such a
modification/adaptation.
[3] This limited warranty covers only the product
hardware. It does not cover technical assistance for
hardware or software usage and it does not cover
any software products whether or not contained in
the product. Any such software is provided “AS IS”
unless expressly provided for in any enclosed software
limited warranty.
[4] This limited warranty is invalid if the factoryapplied serial number has been altered or removed from
the product.
[5] Free inspections and maintenance/repair work
are expressly excluded from this limited warranty, in
particular, if caused by improper handling of the product
by the user. This also applies to defects caused by normal
wear and tear, in particular, of faders, crossfaders,
potentiometers, keys/buttons, guitar strings, illuminants
and similar parts.
[6] Damage/defects caused by the following conditions
are not covered by this limited warranty:
• improper handling, neglect or failure to operate the
unit in compliance with the instructions given in
BEHRINGER user or service manuals;
• connection or operation of the unit in any way
that does not comply with the technical or safety
regulations applicable in the country where the
product is used;
• damage/defects caused by acts of God/Nature
(accident, fire, flood, etc) or any other condition that
is beyond the control of MUSIC Group.
behringer.com
[7] Any repair or opening of the unit carried out by
unauthorized personnel (user included) will void the
limited warranty.
[8] If an inspection of the product by MUSIC Group
shows that the defect in question is not covered by the
limited warranty, the inspection costs are payable by
the customer.
[9] Products which do not meet the terms of this
limited warranty will be repaired exclusively at the buyer’s
expense. MUSIC Group or its authorized service center will
inform the buyer of any such circumstance. If the buyer
fails to submit a written repair order within 6 weeks after
notification, MUSIC Group will return the unit C.O.D. with
a separate invoice for freight and packing. Such costs will
also be invoiced separately when the buyer has sent in a
written repair order.
[10] Authorized BEHRINGER dealers do not sell new
products directly in online auctions. Purchases made
through an online auction are on a “buyer beware” basis.
Online auction confirmations or sales receipts are not
accepted for warranty verification and MUSIC Group will
not repair or replace any product purchased through an
online auction.
§ 5 Warranty transferability
This limited warranty is extended exclusively to the
original buyer (customer of authorized retail dealer) and
is not transferable to anyone who may subsequently
purchase this product. No other person (retail dealer, etc.)
shall be entitled to give any warranty promise on behalf
of MUSIC Group.
§ 6 Claim for damage
Subject only to the operation of mandatory applicable
local laws, MUSIC Group shall have no liability to the buyer
under this warranty for any consequential or indirect
loss or damage of any kind. In no event shall the liability
of MUSIC Group under this limited warranty exceed the
invoiced value of the product.
§ 7 Limitation of liability
This limited warranty is the complete and exclusive
warranty between you and MUSIC Group. It supersedes
all other written or oral communications related to this
product. MUSIC Group provides no other warranties for
this product.
§ 8 Other warranty rights and
national law
[1] This limited warranty does not exclude or limit the
buyer’s statutory rights as a consumer in any way.
[2] The limited warranty regulations mentioned herein
are applicable unless they constitute an infringement of
applicable mandatory local laws.
[3] This warranty does not detract from the seller’s
obligations in regard to any lack of conformity of the
product and any hidden defect.
§ 9 Amendment
Warranty service conditions are subject to change without
notice. For the latest warranty terms and conditions
and additional information regarding MUSIC Group’s
limited warranty, please see complete details online at
behringer.com.
* MUSIC Group Macao Commercial Offshore Limited of
Rue de Pequim No. 202-A, Macau Finance Centre 9/J, Macau,
including all MUSIC Group companies
5
EURODESK SX2442FX/SX3242FX User Manual
1. Introduction
FBQ Feedback Detection System
One of the most outstanding features of this console is the
FBQ Feedback Detection System, which is part of the graphic
equalizer. This ingenious circuit makes it possible to detect and
subsequently eliminate feedback frequencies very quickly.
FBQ increases the brightness of the EQ fader LEDs for the frequency bands where
feedback is occurring. What used to be a tedious search for feedback frequencies
is now mere child’s play.
XENYX Mic Preamps
The microphone channels feature high-end XENYX Mic Preamps
that compare well with costly outboard preamps in terms of sound
quality and dynamics and boast the following features:
• 130 dB dynamic range for an incredible amount of headroom
• A bandwidth ranging from below 10 Hz to over 200 kHz for crystal-clear
reproduction of even the finest nuances
• The extremely low-noise and distortion-free circuitry guarantees absolutely
natural and transparent signal reproduction
• They are perfectly matched to every conceivable microphone with up to
60 dB gain and +48 volt phantom power supply
• They enable you to use the greatly extended dynamic range of your
24-bit/192-kHz HD recorder to the full, thereby maintaining optimal
audio quality
“British EQ”
The equalizers used for the XENYX Series are based on the legendary circuitry of
top-notch consoles made in Britain, which are renowned throughout the world
for their incredibly warm and musical sound character. Even with extreme gain
settings these equalizers ensure outstanding audio properties.
What is more, the EURODESK comes with two effects processors
using 24-bit A/D and D/A converters and the effects algorithms of
our renowned 19" multi-effects device VIRTUALIZER PRO
DSP2024P. Each processor offers 99 presets with first-class room
simulations, delay and modulation effects as well as compressor, tube distortion
and numerous other effects available—all with excellent audio quality!
The mixer is equipped with a state-of-the-art integrated
switch-mode power supply. Unlike conventional designs,
this supply automatically adapts to supply voltages between
100 and 240 V. With its considerably higher efficiency, it is also
more economical in terms of power consumption than standard power supply units.
1.1 Before you get started
1.1.1 Shipment
Your product was carefully packed at the factory to ensure safe transport.
Nevertheless, if the box is damaged inspect the unit immediately for signs
of damage.
◊ If the unit is damaged please do NOT return it to us, but notify your
dealer and the shipping company immediately; otherwise, claims for
damage or replacement may not be granted.
◊ We recommend that you use a flight case to give the unit optimum
protection during use or transport.
◊ Always use the original box to prevent damage during storage
or transport.
behringer.com
◊ Make sure that children cannot play unsupervised with the unit or
its packaging.
◊ Please ensure proper disposal of all packing materials.
1.1.2 Initial operation
Ensure adequate air supply and to avoid overheating do not place the unit
near radiators etc.
◊ Blown fuses must be replaced by fuses of the correct rating!
Please refer to the “Specifications” section for the applicable rating.
For connection to the mains use the enclosed power cord with cold connector
which complies with the relevant safety regulations.
◊ Please make sure that all devices are properly grounded. For your own
safety, never remove or disable the ground conductors from the devices
or on the power cords. The unit must always be connected to the mains
outlet with a protective grounding connection.
◊ We would like to point out that high volume levels may damage your
hearing and/or your headphones/loudspeakers. To avoid switch-on/off
thumps from the console and any downstream devices, always make
sure that your power amp(s) or active speakers are the last components
that are switched on and the first to be switched off. Always make sure
that the appropriate volume is set.
Important notes concerning installation
◊ The sound quality may diminish within the range of powerful
broadcasting stations and high-frequency sources. Increase the
distance between the transmitter and the device and use shielded
cables for all connections.
1.1.3 Online registration
Please register your new BEHRINGER equipment right after your purchase
by visiting http://behringer.com and read the terms and conditions of our
warranty carefully.
Should your BEHRINGER product malfunction, it is our intention to have it
repaired as quickly as possible. To arrange for warranty service, please contact
the BEHRINGER retailer from whom the equipment was purchased. Should your
BEHRINGER dealer not be located in your vicinity, you may directly contact
one of our subsidiaries. Corresponding contact information is included in the
original equipment packaging (Global Contact Information/European Contact
Information). Should your country not be listed, please contact the distributor
nearest you. A list of distributors can be found in the support area of our website
(http://behringer.com).
Registering your purchase and equipment with us helps us process your repair
claims more quickly and efficiently.
Thank you for your cooperation!
1.2 The manual
This manual is designed to give you an overview of all control elements and
at the same time inform you in detail about how to use them. To provide you
with a clear structure, we have grouped the control elements according to their
function. They can easily be found on the enclosed numbered illustrations.
If you need more detailed information on specific topics, please visit our web site
at behringer.com. The product-related information pages and the ULTRANETbased glossary explain the relevant audio engineering terminology in full detail.
6
EURODESK SX2442FX/SX3242FX User Manual
2. Control Elements and
Connections
This chapter describes the various control elements of your mixing console.
All controls and connections are explained in full detail.
2.1 Mono input channels
2.1.1 Microphone and line inputs
The second scale has a gain from +10 to -40 dBu for the line input.
For devices with a nomal line output level of-10 dBV or +4 dBu the setting
is as follows: with GAIN fully counter-clockwise connect the external device
and adjust the output level recommended by the manufacturer. If available,
the output level display of the external device should read 0 dB with signal
peaks. For +4 dBu increase GAIN, for -10 dBV increase it further. The finetuning can be done with a music signal and the LEVEL SET LED, which will
illuminate when the optimum operating level has been set.
[5] Mono channels are equipped with a high-slope LOW CUT filter eliminating
unwanted low-frequency signals, such as floor rumble (18 dB/oct., -3 dB
at 80 Hz).
2.1.2 Equalizer
[1]
All mono input channels are equipped with a 3-band equalizer. The maximum
boost/cut of the individual bands is 15 dB, in mid position the EQ is set to neutral.
[2]
[6]
[3]
[7]
[4]
[5]
[8]
Fig. 2.1: Connectors and controls of the mic/line inputs
[1] Each mono input channel is equipped with a balanced microphone input
on an XLR connector, which provides +48 V phantom power for condenser
microphones at the touch of a button (see rear panel).
◊ Be sure to switch off your audio system before you activate the
phantom power supply to prevent audible switch-on thumps from
reaching your monitor speakers. Please also note the information given
in chapter 2.11 “Rear panel”.
[2] Each mono input also has a balanced line input on ¼" TRS connectors.
Of course, these inputs can also be used with unbalanced plugs
(¼" TS connector).
[3] The INSERT I/O connector is used to process a signal with dynamic
processors or equalizers. This insert point isprefader, pre-EQ and
pre-aux send.
Unlike reverb and other effects, which are usually added to the dry signal,
dynamic processors process the entire signal. So, aux send buses are not the
best solution here. Instead, dynamic processors and equalizers are inserted
into the signal path. Once processed, the signal then re-enters the mixing
console at the same point where it left. Signal interruption only occurs if
a plug is inserted into the corresponding jack (¼" stereo plug: tip = signal
output, ring = input). All mono input channels are equipped with insert
points. They can also be used as pre-EQ direct outputs, without signal
flow interruption. For this you need a cable with a ¼" TS connector on the
recorder/effects processor end, and a bridged stereo ¼" TRS connector on
the console end (tip and ring interconnected).
[4] The GAIN control adjusts the input gain. Be sure to set this control fully
counter-clockwise before you connect or disconnect a signal source to or
from one of the inputs.
GAIN has a dual scale: the first scale has a gain from +10 to +60 dB for
the MIC input.
behringer.com
Fig. 2.2: Equalizer section of input channels
[6] The HIGH control in the EQ section controls the high frequency range of
the respective channel. It is a shelving-type filter which can boost or cut all
frequencies above a fixed frequency (12 kHz).
[7] The MID control allows you to raise or lower the mid-range level. It is a semiparametric peak filter, which boosts or cuts the frequency range around a
variable mid-range frequency. Use the FREQ control to select the mid-range
frequency from 100 Hz to 8 kHz. Then use the MID control to boost or cut the
selected frequency range.
[8] The LOW control boosts or cuts the low-frequency range. Like the HIGH filter
it is a shelving-type filter, which raises or lowers the level of all frequencies
below a specific frequency (80 Hz).
2.1.3 Aux/FX send buses
Aux sends enable you to take the signals from one or multiple channels and
collect them on one bus. This signal is then present at one of the aux send jacks,
from where it can be routed to an active monitor speaker or external effects
device, for example. The FX returns are subsequently used as a return bus for the
processed signal.
[9]
[10]
[11]
Fig. 2.3: AUX/FX send controls in the channel strips
7
EURODESK SX2442FX/SX3242FX User Manual
[9] On each channel, the AUX 1 and AUX 2 controls allow you to determine the
level of the aux signals sent from the channel. The main aux send signal
comprising the aux send signals from all channels can then be adjusted
with the corresponding master AUX SEND controls [51], and is present at the
AUX SEND outputs [52]. Both aux sends are mono, post-EQ, with a gain of up
to +15 dB.
[10] Press the PRE switch to set all aux sends to pre-fader. In this case,
the volume of the aux signals is no longer dependent on the fader position,
so you can create completely independent monitor mixes.
[15] The SOLO switch routes the channel signal to the solo bus (Solo In Place)
or the PFL bus (Pre Fader Listen). Thus, you can monitor a channel signal
without affecting the main output signal. The signal to be monitored is
taken either pre (PFL, mono) or post-panorama control (Solo, stereo) and
post-channel fader (depending on the position of the SOLO/PFL switch [40] ).
[16] The SUB switch routes the signal to the respective subgroups.
Your EURODESK features 4 subgroups (1-2 and 3-4). With the PAN control on
the input channel (see [12]) you can determine to which of the two groups the
signal is routed (hard left: sub 1 or 3, hard right: sub 2 or 4).
◊ For most applications when controlling an external effects device from
one of the aux buses, the aux sends must be set post-fader, so that
the effect volume in a channel depends on the position of the channel
fader. Otherwise, the effect signal would still be audible, even if the
channel was turned down completely. For this type of application it is
advisable to leave the PRE switch out (= not pressed).
[17] The MAIN switch routes the signal to the main mix.
[11] FX 1 and FX 2 controls provide a direct route to the built-in effects processor.
Additionally, they can be used to control an external effects unit, via the
FX SEND 1 and 2 outputs (similar to the AUX SEND 1 and 2 jacks). To ensure
that the internal effects processor and the FX SEND outputs actually get a
signal, the corresponding FX control must not be set fully counter-clockwise
(-oo), and the master FX SEND (see [60] ) must be turned up. The FX buses are
hard wired post-fader.
2.2.1 Channel inputs
◊ Please also read chapter 2.10 “Effects section” and
3 “Digital effects processor”.
[18] The channel fader governs the level of the channel signal as part of the main
mix (or submix).
2.2 Stereo channels
[19]
[20]
2.1.4 Mono channel fader and further control elements
Fig. 2.5: Stereo channel inputs
[12]
[13]
[19] Each stereo channel is equipped with two balanced line-level inputs on
¼" TRS connectors for the left and right channels. The channels can also
process mono signal, as long as you use the “LEFT” jack only.
[14]
[15]
[20] All stereo channel strips have a GAIN control for gain adjustment. Its scale
ranges from +20 to -20 dB and allows you to adapt the input level to the
line inputs.
2.2.2 Stereo channel equalizer
[16]
[17]
[18]
[21]
Fig. 2.4: Channel fader, pan control, mute button, etc.
[12] The PAN control determines the position of the channel signal in the
stereo mix as well as the subgroup to which the channel signal is routed
(see chapter 2.4).
[13] Use the MUTE switch to mute the channel signal, so it is no longer part of
the main mix. At the same time, all aux buses set to post-fader are muted for
the respective channel, while the pre-fader monitor buses remain operative.
The MUTE LED is illuminated when the channel is muted.
[14] The CLIP LED illuminates when the channel overloads. In this case,
please reduce the input gain using the GAIN control. This LED also illuminates
when you activate the solo function with the SOLO switch below.
behringer.com
Fig. 2.6: Stereo channel equalizer
The stereo channels are equipped with a stereo equalizer. The filter types
and cutoff frequencies for HIGH and LOW filters are the same as on the mono
channels. Instead of one semi-paramtric midrange band, the stereo channels
have two separate midrange bands [21] (HIGH MID and LOW MID) with fixed
mid-frequencies (3 kHz and 400 Hz). Stereo EQs are preferable for processing
the frequency response of stereo signals. With two mono equalizers you might
encounter problems with different settings between the left and right channels.
8
EURODESK SX2442FX/SX3242FX User Manual
2.2.3 Stereo channel aux/FX send buses
2.4 Subgroups 1 - 4
Basically, the aux and FX buses on the stereo channels are the same as on the
mono channels. Since aux buses are always mono, the signal from a stereo
channel is first mixed to mono before it is routed to the aux bus.
[26]
2.2.4 Stereo channel fader and other control elements
[27]
[22]
[25]
Fig. 2.9: Subgroups 1 - 4
The EURODESK has 4 subgroups enabling you to create mono or stereo mixes
from multiple input signals. Subgroups are controlled from one (mono) or two
(stereo) subgroup faders. Additionally, it is possible to connect the subgroup
outputs as tape sends to a multi-track recorder.
[25] The subgroup faders determine the volume of the subgroup signal at the
subgroup output [28]. Depending on the position of the routing switch [27]
you can thus control the subgroup volume in the main mix.
Fig. 2.7: Channel fader, balance control, mute switch, etc.
[22] The BAL(ANCE) control has the same function as the PAN control on
the mono channels. It determines the relative volume of the left and
right input signals before they are routed to the stereo main mix bus
(or to two subgroups).
All other control elements of the stereo channels work in the same ways as their
counterparts on the mono channels (faders, MUTE switches, etc.).
◊ Please note: When you route a stereo channel to the subgroups
using the SUB switches, please be sure to set the BAL control to
its mid position, so that the signal is sent to two subgroups and
remains stereo.
2.3 Stereo channels 21-24 (SX2442FX) or
29-32 (SX3242FX)
[26] The SOLO switch routes the subgroup signal to the solo bus (Solo In Place)
or PFL bus (Pre Fader Listen), so that you can monitor the subgroup signal
without affecting the main or sub output signals. The signal to be monitored
is taken either pre (PFL, mono) or post-subgroup fader (Solo, stereo),
depending on the position of theSOLO/PFL switch [40]). The SOLO LED
illuminates when the SOLO switch is pressed.
[27] Use the routing switches for the subgroups to send the subgroup signal to
the main mix. You can route it to the left stereo side (=LEFT pressed), to the
right stereo side (=RIGHT pressed) or to both (=LEFT and RIGHT pressed).
For example, when you have created a stereo submix using subgroups
1 and 2, be sure to route group 1 to the left and group 2 to the right side
to maintain proper stereo positioning. If it is a mono submix with just one
subgroup, route it to the left and right sides of the main mix to make the
signal audible on both sides.
[28]
[23]
Fig. 2.10: Subgroup outputs 1 - 4
[24]
Fig. 2.8: Auxiliary stereo channels
Your EURODESK has two stereo channels with an aux send section [23]
(AUX 1 and AUX 2) and one LEVEL control. [24] For these channels, the aux buses
are hard-wired to pre-fader and are therefore particularly useful for monitoring.
They have no routing switches and are always sent to the main mix. Like the
normal stereo channels they have two line-level inputs on ¼" TRS connectors
for the left and right channels, and a SOLO switch.
Similar to the CD/TAPE inputs (see [49] ) the auxiliary stereo channels can
be connected to CD players, tape decks, etc., for example, to feed in
playback material.
behringer.com
[28] These four SUBGROUP OUT (puts) carry the signals of the individual
subgroups. For multi-tracking connect the outputs to the inputs of a
multi-track recorder (see chapter 4.1 “Studio set-up”).
9
EURODESK SX2442FX/SX3242FX User Manual
2.5 Mono out section for
subwoofer applications
Using this auxiliary mono output you can route the main mix signal to a separate
power amp. The tunable low-pass filter allows you to limit the signal content to
the low-frequency range to get a perfect subwoofer signal. This signal is mono
because very low frequencies disperse quickly, so there would be no benefit to
position this signal in the stereo mix.
[30]
[33] Use this high-precision MAIN fader to control the output level of the main mix.
[34]
Fig. 2.14: XLR main out connectors
[31]
[29]
[34] The MAIN OUT(puts) are balanced XLR connectors with a nominal operating
level of +4 dBu and provide the main mix signal.
[36]
[35]
Fig. 2.15: Main out connectors and main insert
[35] The MAIN OUT ¼" TRS connectors outputs also provide the main mix signal.
Fig. 2.11: Mono out fader and low-pass filter
[29] The MONO fader controls the volume of the signal present at the
MONO OUT (see [32] ).
[30] The FREQ control adjusts the cut-off frequency of the low-pass filter
(30 to 200 Hz). Frequencies above cut-off are filtered out when activated.
[36] Like the channel inserts, the MAIN INSERT connectors can be used to
connect a dynamics processor or equalizer for further processing of the
mix signal. The MAIN INSERT refers to the Main Outs (XLR and ¼" TRS
connectors), the MONO OUT (see [32] ) and, if the MAIN switch in the
PHONES/CONTROL ROOM section is pressed, also to the PHONES/CTRL ROOM
output (see [46] ).
[31] Use the LOW PASS FILTER switch to activate the filter function (LED illuminates).
[32]
[37]
[38]
fig. 2.12: Mono out connector
[39]
[32] The MONO OUT connector provides the line-level mono signal for
connection to the inputs of a power amp or active speaker. You can also use
this output as a monitor bus, e.g. to connect a headphone amplifier. In this
case, the signal should of course not be limited by the low-pass filter.
2.6 Main out section
[40]
Fig. 2.16: Level meter
[37] The red “+48 V” LED illuminates when phantom power is on.
Phantom power is required for the operation of condenser microphones,
and can be switched on with the corresponding switch on the rear of
the console.
[38] The POWER LED is illuminated when the console is switched on.
[33]
Fig. 2.13: Main out fader
behringer.com
[39] The high-precision level meter accurately indicates the output signal level.
For example, when you press the SOLO switch on one of the input channels,
its signal level will be displayed here, either pre-fader (PFL) or post-fader
(SOLO), depending on the position of the SOLO/ PFL switch (see [40] ). In PFL
mode only the left display is active, because the PFL signals are mono.
10
EURODESK SX2442FX/SX3242FX User Manual
[40] The SOLO/PFL switch determines whether the monitored signal is pre
(PFL) or post-fader (SOLO) after pressing the SOLO/PFL switch (the LED
illuminates). The level meter indicates the corresponding signal (see [39] ).
When you adjust a signal with the GAIN control, it is advisable to select PFL
mode, so that the level shown is independent of the channel fader position.
2.6.1 Talkback
The talkback function of the EURODESK allows you to communicate with
the musicians in the recording room or on the stage. The talkback signal
is present at the AUX SEND outputs, which are particularly useful for
monitor/ headphone mixes.
◊ IMPORTANT! High volume levels may damage your hearing and/or
your headphones/loudspeakers. To avoid switch-on/off thumps from
the console and any downstream devices, always make sure that the
power amp(s) or active speaker(s) are the last components that are
switched on and the first to be switched off. Always make sure that the
appropriate volume is set.
2.7 CD/tape
[44]
[48]
[41]
[43]
Fig. 2.20: CD/tape
[47] TO MAIN controls the volume of, for example, a CD player connected to the
CD/tape input connectors (see [49] ).
[42]
Fig. 2.17: Talkback section
[41] The LEVEL control determines the volume of the talkback signal at the
AUX 1/2 outputs.
[42] Use the TALK TO AUX 1/2 switch to activate the built-in talkback
microphone. Its signal is sent to the AUX SEND jacks 1 and 2. Keep the
switch pressed while you’re speaking.
[43] This is the built-in talkback microphone.
[48] When the STANDBY switch is pressed, all input channels are muted. Only the
CD/tape signal will be routed to the main mix. In this way, you can prevent
the microphones from pickung up unwanted sounds or noise that would
interfere with CD playback during a break. The main mix and channel faders
can remain in their normal positions while playing back music from CD
(using the CD/ TAPE INPUTs [49] ), so you don’t lose your mix.
[49] [50]
2.6.2 Phones & control room
[44]
[43]
Fig. 2.21: CD/tape connectors
Fig. 2.18: Phones/control room section
[44] The PHONES/CTRL R control adjusts the volume of the headphones
connected to the PHONES/ CTRL ROOM OUT jack (see [46] ). If you have an
active monitor speaker or power amp connected here, you can also control
the monitor volume.
[45] These switches select the signal sent to the PHONES/ CTRL ROOM jack.
Available sources are: MAIN, CD/TAPE, AUX 1/2 and subgroups 1 - 2 and 3 - 4.
[49] The CD/TAPE INPUT RCA connectors are for the connection of CD players,
tape decks or other line-level sources. The signal volume is adjusted with
the TO MAIN control.
[50] The CD/TAPE OUTPUT RCA connectors provide the stereo main mix signal to
a tape deck or DAT recorder to record your mix. The signal is taken pre-fader,
so that it will not be influenced by the fader positions.
2.8 Master Aux Send 1 and 2
[46]
[51]
Fig. 2.19: Phones/control room output
[46] Connect your headphones or monitor speaker to the PHONES/CTRL
ROOM OUT ¼" TRS connector.
Fig. 2.22: Master aux sends
behringer.com
11
EURODESK SX2442FX/SX3242FX User Manual
[51] These are the master AUX SEND controls 1 and 2 for adjusting the volume
level sent to the corresponding aux send connectors (see [52] ). This way,
you can control the mix of all AUX 1 or AUX 2 signals of the input channels.
The AUX SEND section also has a SOLO switch.
2.10 Effects section
[57]
[52]
[58]
[59]
[60]
[65]
[61]
Fig. 2.23: Master aux send outputs
[52] Use the AUX SEND outputs 1 and 2 to take the master AUX SEND
signals and route them to an external effects device or your monitor
speakers. Subsequently, you can return the effect signal, e.g. via the
STEREO FX RETURN inputs (see [67] ) or specific input channels.
2.9 Graphic 9-band stereo equalizer
[53]
[56]
[62]
[63]
[64]
Fig. 2.25: The digital effects processor
[57] Here you will find a list of all multi-effects presets (see also chapter 3
“Digital effects processor”).
[58] The FX LED level meters show the effects processor’s input signal.
Be sure that the clip LED only illuminates with signal peaks. If it is lit
all the time, the effects processor is overloading and hence producing
unpleasant distortion.
[59] The Effect displays show the currently selected presets.
[55] [54]
Fig. 2.24: The graphic stereo equalizer
[53] Your EURODESK is equipped with a graphic 9-band stereo equalizer
processing either the main or the AUX 1 signal. Use the EQ to adapt the
sound to the room acoustics.
[54] Use the EQ IN switch to switch the equalizer on. In this case, the fader
LEDs illuminate.
[55] With the MAIN/AUX 1 switch you can determine the signal to be processed,
either main or AUX 1.
[56] Press the FBQ IN switch to activate the FBQ Feedback Detection System.
The frequencies causing feedback are indicated by the brightly lit fader
LEDs, while all other LEDs are darker. Simply lower the level of the brightly
lit faders until feedback disappears.
◊ When the switch is in the “AUX 1” position (see [55] ), the EQ fader
LEDs show both the MAIN and the AUX 1 signal simultaneously.
However, if feedback occurs in one of the signals, those signals without
feedback will be faded out to enable clear identification of where
feedback is occurring. If the MAIN signal happens to be the one carrying
feedback, put the switch [55] to “MAIN” and then use the 9-band EQ to
remove the feedback.
behringer.com
[60] This is the master FX 1 (or 2) SEND control for adjusting the volume of all
FX send signals at the corresponding FX send jacks (see [66] ) and at the
inputs of the built-in effects processor. Use it to control the master signal of
all FX 1/FX 2 signals from the input channels. When neither of the FX SEND
controls is turned up, the effects processor will not receive a signal.
[61] Turn the FX 1 (or FX 2) control to select an effects preset. Then, push it
briefly to confirm your selection and activate the new effect.
[62] The FX 1 (or 2) TO AUX 1 controls allow you to add the effect signal from
the built-in effects processor (FX1 or FX2) to the AUX 1 monitor signal.
Naturally, the effects processor must be provided with an input signal
(i.e. the FX controls in the channel strips plus the FX SEND controls and the
channel faders must be turned up).
[63] This is the FX 1 (or 2) TO AUX 2 control adding the effect signal from the
effects processor to the AUX 2 monitor signal. See [62] for further details.
[64] The FX 1 (or 2) TO MAIN control routes the effect signal either to the main
mix or the subgroups 1 and 2 (or 3 and 4), depending on the position of the
selector switch (see [65] ). When it is hard left, no effect signal will be audible.
Here, too, the FX controls in the channel strips plus the FX SEND controls and
the channel faders must be turned up.
12
EURODESK SX2442FX/SX3242FX User Manual
[65] These selector switches route the effect signal to the main mix or to the
subgroups 1-2 or 3-4. If the MAIN/SUB switch is not pressed, the effect
signal is sent to the main mix and the SUB 1/2 / SUB 3/4 switch below
is inoperative. If the upper switch is pressed (SUB), however, the lower
switch determines whether the effect signal is routed to subgroups 1 and 2
(SUB 1/2) or 3 and 4 (SUB 3/4).
[67]
[70] With the PHANTOM switch you can activate the phantom power supply
for the XLR connectors of the mono channels for condenser microphones.
The +48 V-LED [37] illuminates when phantom power is on. In most cases,
dynamic microphones can still be used as long as they are connected in
a balanced configuration. If in doubt, please contact the manufacturer of
your microphone!
[71] The mains connection is a standard IEC receptacle. An appropriate power
cord is supplied with the unit.
[66]
[72] FUSE HOLDER. Before connecting the unit to the mains, ensure that
the voltage setting matches your local voltage. Blown fuses should only
be replaced by fuses of the same type and rating. Please also read the
information given in chapter 6 “Specifications”.
[73] SERIAL NUMBER.
Fig. 2.26: FX send and return connectors
[66] The FX SEND 1 and 2 connectors also provide the master FX send signals,
for example, to connect them to the inputs of an external effects device.
However, these are “dry” signals only with no “effect signals” from the
built-in effects processor!
3. Digital Effects Processor
[67] The Stereo FX RETURN inputs 1 and 2 return the effect signals from external
effects processors and add them to the main mix.
Fig. 3.1: List of all effects presets
[68]
99 FIRST-CLASS PRESETS
Fig. 2.27: Footswitch connectors
[68] The FOOTSW(ITCH) connector allows you to connect a standard dual
footswitch to separately enable/disable FX 1 or FX 2. The tip of the ¼" plug
controls FX 1, the ring controls FX 2.
2.11 Rear panel
Here is the list of all multi-effects presets. The built-in
effects processor offers you various standard effects such as
reverb, chorus, flanger, delay and a variety of combination
effects from our renowned studio effects processor
VIRTUALIZER PRO DSP2024P. Use the FX control on the channels and the FX SEND
control to supply the effects processor with signals. A built-in digital stereo
effects processor has the benefit of no external wiring, thus reducing the risk of
ground loops or level differences. Handling is therefore much easier.
PARALLEL FX
The effects presets 1 to 70 provide classic “add-to-mix” effects. So, when you
turn up the FX 1 (or 2) TO MAIN control, you create a mix of the (dry) channel
signal and the effect signal. The balance between the two signals can be set
with the FX send and FX 1/2 TO MAIN controls.
[72]
[71]
[69]
[70]
[73]
Fig. 2.28: The rear panel of the EURODESK
[69] Use the POWER switch to put the mixer into operation. This switch should
always be in the “Off” position when you connect your unit to the mains.
◊ Please note: The POWER switch does not fully disconnect the unit from
the mains. To disconnect the unit from the mains, pull out the main
cord plug or appliance coupler. When installing the product, ensure the
plug or appliance coupler is readily operable. Unplug the power cord
when the unit is not used for prolonged periods of time.
behringer.com
This also applies to adding effect signals to the AUX 1 (or 2) monitor mix, with the
exception that the mix here is adjusted with the AUX 1 (or 2) control in the
channel strip and the FX TO AUX 1 (or 2) potentiometer. Of course, the effects
processor must receive a signal from the channel using the FX 1 (or 2) control.
Make sure that the PRE switch in the corresponding channel strip(s) is pressed.
Otherwise, the AUX buses will be set post-fader making the volume of the
AUX monitor signal dependent on the position of the channel fader(s).
INSERT FX (channel is muted)
Effects presets #71 and higher process the entire signal, unlike the “add-tomix” effects. When you use an insert preset, be sure to separate the respective
channel from all buses (SUB button and MAIN button not pressed) and only
route the effect signal to the main mix (FX 1/2 control, FX SEND 1/2 control and
FX TO MAIN 1/2 control).
◊ The channel fader of the corresponding channel remains active and
governs (in combination with the FX controls) the signal level sent to
the built-in effects processors.
13
EURODESK SX2442FX/SX3242FX User Manual
4. Wiring Examples
on the remaining two tracks. The four return paths from the recorder are
connected to four separate mono input channels on the EURODESK. The built-in
compressor is used only for the bass, which is why this input channel is separate
from all buses (SUB and MAIN switch not pressed). The bass signal is directly
routed from the built-in effects processor to the respective subgroups
(FX TO MAIN control). The MAIN/SUB switch in the FX1 section is pressed,
but NOT the SUB 1/2 SUB 3/4 button.
4.1 Studio set-up
The following wiring example shows a studio set-up for 4-track-recording:
the drums are mixed down to two subgroups and then routed via the subgroup
outputs to two tracks of the multi-track recorder. The remaining two subgroups
are used to record the guitar, keyboard (stereo channel) and two vocal signals
K
I
C
K
D
R
U
M
S
N
A
R
E
Keyboard
Bass
Drums
O
V
E
R
H
E
A
D
O
V
E
R
H
E
A
D
L
R
Multi-trackrecorder
Guitar
Vocals 1
Vocals 2
Tape Returns
L
R
Subgroups Outs
EUROPOWER EP1500
HPS3000
TRUTH B2030P
SUB 3-4 switch
SUB 1-2 switch
pressed
pressed
SUB/MAIN switches
not pressed
SUB 3-4 switch
pressed
MAIN switch
pressed
Fig. 4.1: Wiring the console for studio operation
◊ Please make sure that none of the subgroup routing switches
(1-2 and 3-4) is pressed in the channels connected to the recorder
returns. Otherwise, a feedback loop will be created as soon as you
start recording. Only press the MAIN switch on these input channels,
so that the tape return signals are routed to the main outs and
Phones/CTRL room outputs of the console.
behringer.com
14
EURODESK SX2442FX/SX3242FX User Manual
4.2 Live set-up
Drums
K
I
C
K
D
R
U
M
S
N
A
R
E
O
V
E
R
H
E
A
D
O
V
E
R
H
E
A
D
L
R
Keyboard
Bass
Guitar
Vocals 1
Vocals 2
L
R
EUROPOWER EP1500
2 x EUROLIVE PROFESSIONAL
Stack (B1800X PRO & B1220 PRO)
EUROPOWER EP1500
SUB 1-2 switch
pressed
SUB/MAIN switches
not pressed
MAIN switch
pressed
Fig. 4.2: Wiring the console for live operation
This example shows a classic live set-up. As in the studio example, four drum
microphones, bass, keyboard (stereo channel), guitar and two vocal microphones
are connected. The four drum channels (kick drum, snare, overhead L, overhead R)
are mixed down to two subgroups and then routed to the main mix. This way,
it is possible to conveniently control the volume of the entire drums in the main
mix with the two subgroup faders. The built-in compressor insert effect is used
for the bass. The corresponding input channel is separate from all buses and the
bass signal is routed directly from the internal effects processor to the main mix
bus. The MAIN/SUB switch must not be pressed in this case and the position of the
SUB 1/2 SUB 3/4 switch is irrelevant.
behringer.com
L/R switch
pressed
EUROLIVE PROFESSIONAL
B1220 PRO
15
EURODESK SX2442FX/SX3242FX User Manual
5. Audio Connectors
The inputs and outputs of the BEHRINGER EURODESK are designed as unbalanced
¼" TS connectors—except for the balanced line inputs of the mono and stereo
channels and the main out connectors. Of course, all inputs and outputs work
with both balanced and unbalanced connectors. The tape ins and outs are stereo
RCA connectors.
◊ Please ensure that only qualified personnel install and operate the
EURODESK. During installation and operation, the user must have
sufficient electrical contact to earth. Electrostatic charges might
affect the operation of the unit.
tip
tip
sleeve
shield
Fig. 5.3: RCA cable
Balanced use with XLR connectors
Unbalanced ¼" TS connector
Strain relief clamp
2 1
3
Sleeve
Tip
input
1 = ground/shield
2 = hot (+ve)
3 = cold (-ve)
Sleeve
(ground/shield)
1
2
3
output
Tip
(signal)
For unbalanced use, pin 1 and pin 3 have to be bridged
Fig. 5.4: XLR connectors
Fig. 5.1: ¼" TS connector
¼" TS footswitch connector
Balanced ¼" TRS connector
strain relief clamp
strain relief clamp
sleeve
sleeve
ring
tip
tip
sleeve
pole 1/ground
sleeve
ground/shield
ring
cold (-ve)
tip
pole 2
tip
hot (+ve)
For connection of balanced and unbalanced plugs,
ring and sleeve have to be bridged at the stereo plug.
The footswitch connects both poles momentarily
Fig. 5.5: ¼" TRS footswitch connector
Fig. 5.2: ¼" TRS connector
behringer.com
sleeve
16
EURODESK SX2442FX/SX3242FX User Manual
¼" TRS headphones connector
strain relief clamp
sleeve
ring
tip
sleeve
ground/shield
ring
right signal
tip
left signal
Fig. 5.6: ¼" TRS connector for headphones
Insert send return ¼" TRS connector
strain relief clamp
sleeve
ring
tip
sleeve
ground/shield
ring
return (in)
tip
send (out)
Connect the insert send with the input and the
insert return with the output of the effects device.
Fig. 5.7: Insert send and return ¼” TRS connector
behringer.com
17
EURODESK SX2442FX/SX3242FX User Manual
6. Presets
Effect
Parallel Effects
Cathedral
Plate
Concert
Stage
Room
Studio
Small Hall
Ambience
Early Reflections
Spring Reverb
Gated Reverb
Reverse Reverb
Chorus
Flanger
Phaser
Rotary Speaker
Delay
Chorus & Reverb
Flanger & Reverb
Phaser & Reverb
Rotary Speaker & Reverb
Delay & Reverb
Delay & Chorus
Delay & Flanger
Insert Effects
Compressor
Description
Application examples
Very dense and long reverberation of a large cathedral.
Simulates the sound of early plate reverberators.
Simulates a small theater or large concert hall.
Very dense reverb, especially for live applications.
You can clearly hear the walls of the room.
Adds spaciousness to the sound; signals sound natural, not “flat”.
Simulates a small, lively (strongly reflecting) hall.
Reproduces a middle-sized room without late reflections.
Very dense reverb with pronounced early reflections.
Simulates a classic spring reverberation.
Reverb that is synthetically cut off
Reverb with reversed envelope, i.e. it slowly gets louder.
Slight detuning of the original signal.
A slightly delayed signal is added to the original signal, producing phase shifting of the signals.
Another phase-shift effect.
Simulation of a classic effect for electronic organ.
Delay of the input signal with several repetitions.
Combination of chorus and reverb.
Flanger combined with a reverb effect.
Phaser combined with a reverb effect.
Rotary Speaker effect combined with reverb.
Delay combined with reverb.
Widens the signals and produces interesting repetition effects.
Similar to Delay & Chorus, but with audible up/downward modulation.
Solo instruments/vocals in slow pieces.
A classic for drums (snare) and vocals.
Creates an “atmosphere” (e.g. radioplay voices).
Dissipates the sound of keyboard pads, for example.
Reverb effect that isn’t directly noticeable.
Gives a sound source more “class” in the mix.
Perfect for processing drums.
Extremely versatile effect.
Drums, percussion, slap bass
Extremely versatile effect.
Produces a very “crisp” snare sound.
Produces a very spaced out vocal sound.
Extremely versatile effect (guitar, vocals, bass, keyboards etc.).
Extremely versatile effect (guitar, vocals, bass, keyboards etc.).
Extremely versatile effect (guitar, vocals, bass, keyboards etc.).
Organ/keyboards.
Extremely versatile effect.
A classic effect for vocals.
All-purpose effect.
All-purpose effect.
Organ/keyboards/electric guitar.
The most common combination for vocals, solo guitar, etc.
Makes vocals stand out in the mix. Good intelligibility is preserved.
Ideal for creating a slightly spaced out sound.
Single signals, especially from microphones.
Gate
Ultramizer
Soft or loud passages are raised or lowered in level respectively.
No dynamics limitation (see Compressor), but quite the opposite: interference
(noise, hum, etc.) is reduced in level.
A gate opens for a specific period of time to make a specific signal pass, and then closes abruptly.
Extremely efficient compression through automatic adaptation of compression parameters.
Ultrabass
Combines sub-harmonics processor, bass exciter and limiter.
Panner
Exciter
Auto Filter
Tube Distortion
Guitar Amp
Vinylizer
Test Tone
The signal “wanders” between the sides of the stereo basis.
Adds synthetic harmonics to the signal, resulting in increased presence and “loudness”.
Level-dependent boost of a specific frequency band, similar to auto-wah effect for electric guitars.
Simulates the tube distortion of classic guitar amplifiers.
Guitar amp simulation.
Adds the clicks and noise of old vinyl records.
1-kHz test tone.
Expander
behringer.com
Single signals, especially from microphones.
“Controls” feedback-prone microphones/eliminates interference.
Gives mix signals a constant output level.
Gives keyboard sounds some special “class”/sound effect for
electric basses.
Special effect, e.g. for radioplay soundtracking.
Both mix and single signals. Improves intelligibility of vocal signals.
DJ-ing/sound effects for live events/electric guitar or bass.
Electric guitar/vocals/keyboards.
Electric guitar or bass.
DJ-ing/sound effects for live events.
Makes P.A. level setting easier.
18
EURODESK SX2442FX/SX3242FX User Manual
7. Specifications
CD/Tape In
Mono Inputs
Microphone inputs (XENYX Mic preamp)
Type
RCA connector
Type
Impedance
approx. 10 kΩ
Max. input level
+22 dBu
XLR connector, electronically balanced, discrete input circuit
Mic E.I.N.1 (20 Hz - 20 kHz)
@ 0 Ω source resistance
-134 dB / 135.7 dB A-weighted
@ 50 Ω source resistance
-131 dB / 133.3 dB A-weighted
@ 150 Ω source resistance
-129 dB / 130.5 dB A-weighted
Frequency Response
<10 Hz - 160 kHz
-1 dB
<10 Hz - 200 kHz
-3 dB
Gain range
+10 dB to +60 dB
Max. input level
+12 dBu @ +10 dB GAIN
Impedance
approx. 2.6 kΩ balanced
Signal-to-noise ratio
110 dB / 112 dB A-weighted
(0 dBu In @ +22 dB GAIN)
Distortion (THD + N)
0.005 % / 0.004 % A-weighted
Line Input
Type
¼" TRS jack,
electronically balanced
Impedance
approx. 20 kΩ balanced,
approx. 10 kΩ unbalanced
Gain range
-10 dB to +40 dB
Max. input level
+22 dBu @ 0 dB GAIN
Fade-out attenuation2 (Crosstalk attenuation)
Equalizer
EQ mono channels
LOW
80 Hz / ±15 dB
MID
100 Hz to 8 kHz / ±15 dB
HIGH
12 kHz / ±15 dB
LOW CUT
80 Hz, 18 dB/oct.
EQ stereo channels
LOW
80 Hz / ±15 dB
LOW MID
500 Hz / ±15 dB
HIGH MID
3 kHz / ±15 dB
HIGH
12 kHz / ±15 dB
Channel Inserts
Type
¼" TRS jack, unbalanced
Max. input level
+22 dBu
AUX/FX Send
Type
¼" mono jack, unbalanced
Impedance
approx. 120 Ω
Max. output level
+22 dBu
FX Returns
Main fader closed
90 dB
Type
¼" mono jack, unbalanced
Channel muted
84 dB
Impedance
approx. 10 kΩ
Channel fader muted
85 dB
Max. input level
+22 dBu
Frequency response (Mic In → Main Out)
<10 Hz - 90 kHz
+0 dB / -1 dB
<10 Hz - 160 kHz
+0 dB / -3 dB
Stereo Inputs
Type
2 x ¼" TRS jack, balanced
Impedance
approx. 20 kΩ balanced,
approx. 10 kΩ unbalanced
Gain range
-20 dB to +20 dB
Max. input level
+22 dBu @ 0 dB GAIN
behringer.com
Subgroup Outputs
Type
¼" mono jack, unbalanced
Impedance
approx. 120 Ω
Max. output level
+22 dBu
Main Outputs (XLR)
Type
XLR connector,
electronically balanced
Impedance
approx. 240 Ω balanced,
approx. 120 Ω unbalanced
Max. output level
+28 dBu
19
EURODESK SX2442FX/SX3242FX User Manual
Main Outputs (¼")
Physical/Weight
Type
¼" TRS jack, electronically balanced
SX2442FX
Impedance
approx. 240 Ω balanced,
approx. 120 Ω unbalanced
Dimensions (H x W x D)
3.9 x 26.9 x 16.1"
100 x 682 x 410 mm
Max. output level
+28 dBu
Weight (net)
19 lbs / 8.6 kg
SX3242FX
Main Inserts
Type
¼" TRS jack, unbalanced
Max. input level
+22 dBu
Mono Output
Weight (net)
24.3 lbs / 11.0 kg
Equivalent Input Noise
Type
¼" mono jack, unbalanced
Impedance
approx. 120 Ω
3
Max. output level
+22 dBu
Low pass
variable, 30 Hz to 200 Hz, 18 dB/oct.
Phones/CTRL Room Output
Type
¼" TRS jack, unbalanced
Max. output level
+19 dBu / 150 Ω (+25 dBm)
CD/Tape Out
Type
RCA connector
Impedance
approx. 1 kΩ
Max. output level
+22 dBu
DSP
Type
Texas Instruments
Converter
24-bit delta-sigma,
64/128-times oversampling
Sampling rate
46 kHz
Main Mix System Data3 (Noise)
-100 dB / -102.5 dB A-weighted
Main mix @ 0 dB, channel fader @ -∞ -82 dB / -85 dB A-weighted
Main mix @ 0 dB, channel fader @ 0 dB -72 dB / -75 dB A-weighted
Power Supply
Power consumption
50 W
Fuse (100 - 240 V~, 50/60 Hz)
T 2,0 A H 250 V
Mains connector
Standard IEC receptacle
behringer.com
3.9 x 35.3 x 16.1"
100 x 896 x 410 mm
1
2
Main mix @ -∞, channel fader @ -∞
Dimensions (H x W x D)
Measuring conditions: 1 kHz rel. to 0 dBu; 20 Hz - 20 kHz; line input; main output; unity gain.
20 Hz - 20 kHz; measured at main output. Channels 1 - 4 unity gain; EQ flat; all channels on main mix;
channels 1/3 as far left as possible; channels 2/4 as far right as possible; reference = +6 dBu.
BEHRINGER is constantly striving to maintain the highest professional standards. As a result of these efforts,
modifications may be made from time to time to existing products without prior notice. Specifications and
appearance may differ from those listed or illustrated.
20
EURODESK SX2442FX/SX3242FX User Manual
FEDERAL COMMUNICATIONS
COMMISSION COMPLIANCE
INFORMATION
EURODESK SX2442FX/SX3242FX
Responsible party name:
MUSIC Group Services USA, Inc.
Address:
18912 North Creek Parkway,
Suite 200 Bothell, WA 98011,
USA
Phone/Fax No.:
Phone: +1 425 672 0816
Fax: +1 425 673 7647
EURODESK SX2442FX/SX3242FX
complies with the FCC rules as mentioned in the following paragraph:
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
Important information:
Changes or modifications to the equipment not expressly approved by MUSIC Group
can void the user’s authority to use the equipment.
behringer.com
behringer.com