Instruction manual | Beko CFD640B Refrigerator User Manual

Frost Free Combi
Fridge / Freezer
CFD640B
CFD640W
CFD640S
Please read this manual first!
Dear Customer,
We hope that your product, which has been produced in a 1st-class manufacturing
facility and checked under the most meticulous quality control procedures, will
provide you with years of good service.
For this, we recommend you to carefully read the entire manual of your product
before using it and keep it at hand for future reference.
This manual
• Will help you use your appliance quickly and safely.
• Read the manual before installing and operating your product.
• Follow the instructions, especially those for safety.
• Keep the manual in an easily accessible place as you may need it later.
• Besides, read also the other documents provided with your product.
Please note that this manual may be valid for other models as well.
Symbols and their descriptions
This instruction manual contains the following symbols:
C Important information or useful usage tips.
AWarning against dangerous conditions for life and property.
BWarning against electric voltage.
1 Your refrigerator 4
2 Warnings
5
Electrical requirements........................6
Warning! This appliance must be
earthed...............................................6
Energy saving tips..............................7
Compliance with WEEE Directive and
Disposing of the Waste Product: .......7
Compliance with rohs directive:.........7
Package information...........................7
3 Installation
8
Points to be considered when retransporting your refrigerator..............8
Before operating your refrigerator.......8
Disposing of the packaging................9
Disposing of your old refrigerator........9
Placing and Installation.......................9
Transportation Instructions................10
Installation Instructions.....................10
Replacing the interior light bulb . .....12
Reversing The Doors........................13
Reversing the doors.........................15
3
4 Before operating 16
Final Check......................................16
5 Using your refrigerator
17
Temperature Control And
Adjustment.......................................17
Suggested Arrangement Of Food In
The Fridge/Freezer...........................18
Storing Frozen Food.........................19
Freezing Fresh Food.........................19
Making Ice Cubes.............................19
Defrosting.........................................20
Water Dispenser...............................21
*optional...........................................21
6 Maintenance and cleaning 23
Protection of plastic surfaces . .........23
7 Recommended solutions for
the problems
24
8 Guarantee Details
28
9 How To Obtain Service
29
EN
1 Your refrigerator
Congratulations on your choice of a BEKO quality Appliance which has been
designed to give you service for many years.
12
11
1
2
3
4
14
13
3
3
5
6
7
8
9
15
9
9
9
10
1.
2.
3.
4.
5.
8. Icebank tray
9. Deep-freeze compartment
10.Adjustable front feet
11.Fridge compartment door shelves
12.Egg holders
13.Water disperser
14.Fridge compartment
15.Freezer compartment
Thermostat control
Interior Light
Adjustable body shelves
Wine rack
Defrost water collection channel Drain tube
6. Crisper cover
7. Crisper
C Figures that take place in this instruction manual are schematic and may not
correspond exactly with your product. If the subject parts are not included in the
product you have purchased, then it is valid for other models.
4
EN
2 Warnings
• Do not connect your appliance to
the electricity supply until all packing
and transit protectors have been
removed.
• If transported horizontally leave
to stand upright for at least 4
hours before switching on to allow
compressor oil to settle
• If you are discarding an old
refrigerator with a lock or latch fitted
to the door, disable the lock/latch,
ensure that it is left in a safe condition
to prevent the entrapment of young
children.
• This fridge/freezer must only be used
for its intended purpose i.e the storing
and freezing of edible foodstuff.
• Do not dispose of the appliance
on a fire. At BEKO, the care and
protection of our environment is an
ongoing commitment. This appliance
which is among the latest range
introduced is particularly environment
friendly. Your appliance contains non
CFC / HFC natural substances in the
cooling system (Called R600a) and in
the insulation (Called cyclopentane)
which are potentially flammable
if exposed to fire. Therefore, take
care not to damage, the cooling
circuit / pipes of the appliance in
transportation and in use. In case of
damage do not expose the appliance
to fire or potential ignition source and
immediately ventilate the room where
the appliance is situated.
• We suggest you contact your local
authority for disposal information and
facilities available.
5
• See Installation Instructions on on
page 8 for information on suitable
location.
• To obtain the best possible
performance and trouble free
operation from your appliance it is
very important to carefully read these
instructions.
• On delivery, check to make sure that
the product is not damaged and that
all the parts and accessories are in
perfect condition.
• Ensure that the plug remains readily
accessible. Do not use multiple
adapter or extension cable.
• Failure to observe these instructions
may invalidate your right to free
service during the guarantee period.
• Keep ventilation openings, in the
appliance enclosure or in the built-in
structure, clear of obstruction.
• Do not use mechanical devices
or other means to accelerate the
defrosting process, other than those
recommended by the manufacturer.
• Do not damage the refrigerant circuit.
• Do not use electrical appliances
inside the food storage
compartments of the appliance,
unless they are of the type
recommended by the manufacturer.
• We suggest you keep these
instructions in a safe place for easy
reference.
EN
• This appliance is not intended for use
by persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience
and knowledge, unless they have
been given supervision or instruction
concerning use of the appliance by a
person responsible for their safety.
• Children should be supervised to
ensure that they do not play with the
appliance.
Electrical requirements
Before you insert the plug into the
wall socket make sure that the voltage
and the frequency shown on the rating
plate inside the appliance corresponds
to yourelectricity supply.
Rating label is on the left hand side of
fridge inner liner.
We recommend that this appliance be
connected to the mains supply via a
Suitable switched and fused socket.
The appliance must be positioned so
that the plug is accessible.
Should the mains lead of the appliance
become damaged or should it need
Replacing at any time, it must be
replaced by a special purpose made
mains lead which can only be obtained
from a BEKO authorised service agent.
The moulded plug on this appliance
incorporates a 13 A fuse. Should the
fuse need to be replaced an ASTABEAB
approved BS 1362 fuse of the same
rating must be used. Do not forget
to refit the fuse cover. In the event of
losing the fuse cover the plug must not
be used until a replacement fuse cover
has been fitted.
Colour of the replacement fuse cover
must be the same colour as that visible
on the pin face of the plug. Fuse covers
are available from any good electrical
store.
Important! Fitting A Different Plug
As the colours of the wires in the
mains lead of this appliance may not
correspond with the coloured markings
identifying the terminals in your plug
proceed as follows: (See diagram).
1. Connect the green-yellow or green
(Earth) wire to the terminal in the plug
marked ‘E’ or with the symbol or
coloured green and yellow or green.
2. Connect the blue (Neutral) wire to
the terminal in the plug marked ‘N’ or
coloured black.
3. Connect the brown (Live) wire to the
terminal in the plug marked ‘L’ or
coloured red.
Warning! This appliance
must be earthed
6
12mm.
6mm.
22mm.
CORD GRIP
EN
FUSE
6mm.
N
BLUE
OR
BLACK
L
BROWN
OR
RED
FITTED WITH
BS 1362 13A FUSE ALWAYS
FIT BS 1362 REPLACEMENT
CARTRIDGE FUSE
6mm.
32mm.
GREEN &
YELLOW
OR
GREEN
If the fitted moulded plug is not suitable
for your socket, then the plug should be
cut off and an appropriate plug fitted.
Destroy the old plug which is cut off as
a plug with bared cord could cause a
shock hazard if inserted into a socket
elsewhere in the house.
With alternative plugs a 13 A fuse must
be fitted either in the plug or adaptor or
in the main fuse box. If in doubt contact
a qualified electrician.
Energy saving tips
1. Ensure your appliance is installed in a
well ventilated area.
2. Ensure the time between buying
chilled/frozen food and placing
them in your appliance is kept at
minimum, particularly in summer. We
recommend you use a cool bag or a
special carrier bag to carry perishable
food.
3. Do not leave the door (s) of your
appliance open longer than
necessary and ensure they are closed
properly after each opening.
4. Defrost frozen food in the fridge
compartment, so that frozen food
acts as an ice pack to assist cooling
in the fridge.
Compliance with rohs
directive:
The product you have purchased
complies with EU RoHS Directive
(2011/65/EU). It does not contain
harmful and prohibited materials
specified in the Directive.
Package information
Packaging materials of the product
are manufactured from recyclable
materials in accordance with our
National Environment Regulations. Do
not dispose of the packaging materials
together with the domestic or other
wastes. Take them to the packaging
material collection points designated
by the local authorities.
Compliance with WEEE
Directive and Disposing of
the Waste Product:
This product complies with EU WEEE
Directive (2012/19/EU). This
product bears a classification
symbol for waste electrical
and electronic equipment
(WEEE).This product has
been manufactured with
high quality parts and
materials which can be reused and are
suitable for recycling. Do not dispose of
the waste product with normal domestic
and other wastes at the end of its
service life. Take it to the collection
center for the recycling of electrical and
electronic equipment. Please consult
your local authorities to learn about
these collection centers.
7
EN
3 Installation
BPlease remember that the
manufacturer shall not be held liable if
the information given in the instruction
manual is not observed.
Points to be considered
when re-transporting your
refrigerator
1. Your refrigerator must be
emptied and cleaned prior to any
transportation.
2. Shelves, accessories, crisper and etc.
in your refrigerator must be fastened
securely by adhesive tape against any
jolt before repackaging.
3. Packaging must be adequate and
the rules of transportation printed on
the package must be followed.
Please do not forget…
Every recycled material is an
indispensable source for the nature and
for our national resources.
If you wish to contribute to recycling the
packaging materials, you can get further
information from the environmental
bodies or local authorities.
Before operating your
refrigerator
Before starting to use your refrigerator
check the following:
1. Is the interior of the refrigerator dry
and can the air circulate freely in the
rear of it?
2. Please install the 2 plastic wedges
as illustrated in the figure. Plastic
wedges will provide the required
distance between your refrigerator
and the wall in order to allow the air
circulation. (The illustrated figure is
only an example and does not match
8
exactly with your product.)
3. Clean the interior of the refrigerator as
recommended in the “Maintenance
and cleaning” section.
4. Plug the refrigerator into the wall
outlet. When the fridge door is open,
the fridge compartment interior light
will come on.
5. You will hear a noise as the
compressor starts up. The liquid and
gases sealed within the refrigeration
system may also give rise to noise,
even if the compressor is not running
and this is quite normal.
6. Front edges of the refrigerator may
feel warm. This is normal. These
areas are designed to be warm to
avoid condensation.
Electric connection
Connect your product to a grounded
socket which is being protected by a
fuse with the appropriate capacity.
Important:
• The connection must be in
compliance with national regulations.
• The power cable plug must be easily
accessible after installation.
• The specified voltage must be equal
to your mains voltage.
• Extension cables and multiway plugs
must not be used for connection.
EN
BA damaged power cable must be
replaced by a qualified electrician.
BProduct must not be operated before
it is repaired! There is danger of
electric shock!
Disposing of the packaging
The packing materials may be
dangerous for children. Keep the
packing materials out of the reach
of children or dispose of them by
classifying them in accordance with the
waste instructions. Do not dispose of
them along with the normal household
waste.
The packing of your refrigerator is
produced from recyclable materials.
2. Keep your refrigerator away from heat
sources, humid places and direct
sunlight.
3. There must be appropriate air
ventilation around your refrigerator
in order to achieve an efficient
operation. If the refrigerator is to be
placed in a recess in the wall, there
must be at least 5 cm distance with
the ceiling and at least 5 cm with
the wall. If the floor is covered with
a carpet, your product must be
elevated 2.5 cm from the floor.
4. Place your refrigerator on an even
floor surface to prevent jolts.
Disposing of your old
refrigerator
Dispose of your old refrigerator without
giving any harm to the environment.
• You may consult your authorised
dealer or waste collection center of
your municipality about the disposal
of your refrigerator.
Before disposing of your refrigerator,
cut out the electric plug and, if there
are any locks on the door, make them
inoperable in order to protect children
against any danger.
Placing and Installation
A If the entrance door of the room
where the refrigerator will be installed
is not wide enough for the refrigerator
to pass through, then carefully remove
the doors of your refrigerator and pass
it sideways through the door.
1. Install your refrigerator to a place that
allows ease of use.
9
EN
Transportation Instructions
1. The appliance should be transported
only in a vertical upright position. The
packing as supplied must be intact
during transportation.
2. If during the course of transport the
appliance has to be transported
horizontally, it must only be laid on its
right hand side when standing in the
front of the appliance. After bringing
it to upright position,it must not be
operated for at least 4 hours to allow
the system to settle.
3. Failure to comply with the above
instructions could result in damage
occuring to the appliance. The
manufacturer will not be held
responsible if these instructions are
disregarded.
4. The appliance must be protected
against rain, moisture and other
atmospheric influences.
5. When positioning your appliance take
care not to damage your flooring,
pipes, wall coverings etc. Do not
move the appliance by pulling by the
door or handle.
6. Empty any water in the drain
tray before moving. See section
‘Defrosting’ and ‘Care & cleaning’ for
further information.
7. Make sure that the defrost water pipe
at the back of the product is fixed
to the plastic evaporating pan on
the top of the compressor, to avoid
defrost water spillage on the floor.
10
IMPORTANT : Care must be taken
while cleaning / carrying the appliance
to avoid touching the bottom of the
condenser metal wires at the back of
the appliance as you might injure your
fingers and hands.
Do not attempt to sit or stand on top
of your appliance as it is not designed
for such use. You could injure yourself
or damage the appliance.
IMPORTANT : Make sure that mains
cable is not caught under the appliance
during and after carrying / moving the
appliance, to avoid the mains cable
becoming cut or damaged.”
Do not allow children to play with the
appliance or tamper with the controls.
BEKO declines to accept any liability
should the instructions not be followed.
Installation Instructions
1. The space in the room where the
appliance is installed must not be
smaller than 10 cubic metres.
2. This appliance is designed to operate
at temperatures specified in the table
below is equipped with Advanced
Electronic Temperature Control
System [AETCS] which ensures
that at the advised setting [4 - four
on the thermostat ] the frozen food
in the freezer will not defrost even if
the ambient temperature falls as low
as -15 °C. So you may then install
your appliance in a garage or an
unheated room without having to
worry about frozen food in the freezer
being spoilt. However at low ambient
temperatures mentioned above,
fridge contents are likely to freeze,
so check and consume food in the
fridge accordingly. When the ambient
EN
temperature returns to normal, you
may change the setting to suit your
needs. If the ambient temperature
is below 0°C, the food in the fridge
compartment will freeze.So, we
recommend you don’t use the fridge
compartment in such low ambient
conditions. You can continue using
the freezer compartment as usual.
3. Do not place the appliance near
cookers, radiators or in direct sunlight
as this will cause your appliance to
work harder. If installed next to a
source of heat or freezer, maintain the
following minimum side clearances:
From Cookers 50 mm (2”)
From Radiators 300 mm (12”)
From Freezers 25 mm (1”)
7. A special receptacle is supplied to
store the mains plug during transit.
The receptacle is fixed at the back
of the cabinet, on the side of the
compressor. (See diagram) Gently
remove the plug from the receptacle.
Never pull the mains cord, you may
damage the appliance. In the case
of transportation, ensure you locate
the plug in the receptacle provided to
avoid transit damage.
4. 4. Make sure that sufficient room is
provided around the appliance to
ensure free air circulation. Fit the two
plastic wall spacers supplied with the
appliance to the condenser on the
back of the appliance by rotating 1/4
turn. (See Diagram).
5. The fridge/freezer should be located
on a smooth surface. The two front
feet can be adjusted as required. To
ensure that your appliance is standing
upright adjust the two front feet by
turning clockwise or anti-clockwise,
until the product is in firm contact with
the floor. Correct adjustment of feet
avoids excessive vibration and noise.
6. Refer to cleaning and care section to
prepare your appliance for use.
11
EN
Replacing the interior light bulb
Should the light fail to work, proceed
as follows.
1. Switch off at the socket outlet and
pull out the mains plug.
• You may find it useful to remove
shelves for easy access.
2. Use a flat tipped screwdriver to
remove the light diffuser cover by
inserting the blade in each of the two
recesses to prise off each side.
3. First check that the bulb hasn’t
worked loose by ensuring it is
screwed securely in the holder.
Replace the plug and switch on. If the
bulb works, replace the light cover by
inserting the rear lug and pushing up
to locate the front two lugs.
4. If the light still fails to work, switch off
at the socket outlet and pull out the
mains plug. Replace the bulb with a
new 15 watt (max) screw cap (SES)
bulb.
5. Carefully dispose of the burnt-out
light bulb immediately. Replacement
light bulb can easily be obtained from
a good local electrical or DIY store.
12
EN
Reversing The Doors
3. Gently prise off plastic hinge covers
on both sides of upper door top trim
and front top panel using a small We recommend that you reverse
flat-headed screwdriver. (1)
doors before switching on for the first
4.
Gently tilt the appliance back
time.
against a strong wall on its rear side
sufficiently to allow the lower hinge
Tools required: Small and medium size
to be removed. Take care to protect
flat and cross-headed screwdrivers, a
the appliance, your wall and floor
pair of pliers.
coverings. You can utilise the original
packaging to do this. Once you tilt
Spare Parts supplied in the plastic
the appliance back, check to make
bag: The following parts, which are
sure the appliance is completely
exclusively for left hand side fitted hinge
stable and safe before you carry on.
operation are supplied in a plastic bag
(2)
with the appliance:
5. Unscrew and remove the lower hinge
using a cross-headed screwdriver
- Upper door top trim hinge covers –
while holding the lower door firmly.(3)
there are 2 different parts, one for each
side of top trim.
6. Remove lower door carefully off the
- Upper door middle hinge bushing/
middle hinge and stand door upright
door stopper assembly.
in a safe place.(4)
7. Open upper door and unscrew
We suggest you keep all the parts
and remove the middle hinge while
supplied in the plastic bag and also
holding the upper door firmly. Use a
parts, which have been removed when
flat-headed screwdriver. Middle hinge
reversing doors, in a safe place for
will need to be rotated 180 degrees
possible future, re-use.
before re-fitting on the opposite side.
(5)
IMPORTANT: We suggest you ask
8. Remove upper door carefully off the
somebody to help you when moving
upper hinge and stand door upright
the appliance around and to hold doors
in a safe place.(6)
when removing / re-fitting hinges and
doors to avoid any injury and damage 9. Unscrew and remove the upper hinge
using a flat-headed screwdriver.(7)
to the product.
10.Rotate the upper hinge 180 degrees
Please refer to diagrams supplied. To
and then unscrew and remove the
follow numbers in brackets below, refer
hinge pin using a pair of pliers and reto the main diagram.
fit to opposite side of hinge.(8)
1. Switch off the appliance at the socket 11.Reposition plugs and hinge pin
outlet and pull out the mains plug.
bushings on top of doors on the
2. Remove all loose items and fittings
opposite side of both doors. Use
and food, if any, from inside the
small flat-headed screwdrivers to
appliance and door racks.
remove plugs and bushings. Take
13 EN care not to mark doors.(9)
12.Reposition left hand side feet on
the opposite side. Unscrew and
reposition the bottom hinge bushing.
(10)
13.Unscrew and remove the upper
door middle hinge pin bushing/
door stopper using a cross-headed
screwdriver. Important: This part
cannot be used on the opposite
side; left hand side middle hinge pin
bushing/door stopper part is supplied
in the plastic bag.(11)
14.Re-fit the upper hinge on the left hand
side using flat-headed screwdriver.
(12)
15.Fit upper door left hand side middle
hinge pin bushing/door stopper
supplied in the plastic bag using
cross-headed screwdriver.(13)
16.Reposition three small plastic plugs
on the left hand side, which are
covering middle hinge holes, on
the opposite side to cover holes left
empty.(14)
17.Locate and re-fit upper door to upper
hinge and hold the door firmly.(15)
18.Locate the middle hinge pin to middle
hinge pin bushing of upper door on
the left hand side and re-fit the middle
hinge.(16)
19.Reposition the two screws fitted to
lower hinge holes on the left hand
side at the bottom of the cabinet on
the opposite side.(17)
20.Locate and re-fit lower door to middle
hinge pin and then re-fit the lower
hinge on the left hand side.(18), (19)
21.Carefully stand the appliance upright
and adjust the two front feet if
necessary.
14
22.Check that doors open and close
easily, they are aligned correctly and
that there are no gaps allowing air into
the cabinet. If there are gaps between
the door seal and the cabinet, adjust
the door seal by gently pulling away
from the door using fingers.
23.Check that all the hinge screws are
tightened. Avoid over tightening the
screws.
24.Put all items, fittings back in the
appliance.
25.Fit upper door top trim and front top
panel plastic hinge covers. Upper
door top trim hinge covers are
supplied in the plastic bag.(20)
26.Wait for at least 4 hours to allow the
system to settle before switching on.
27.Once the correct storage
temperatures have been reached in
the appliance, put back all the food.
EN
Reversing the doors
Proceed in numerical order .
1
(8)
(13)
20
7
1
1
6
2
5
14
11
13
45 °
9
4
3
10
12
20
8
15
180°
20
16
19
21
18
21
17
15
EN
4 Before operating
Final Check
Before you start using the fridge/
freezer check that:
1. The feet have been adjusted for
perfect levelling.
2. The interior is dry and air can circulate
freely at the rear of the cabinet.
3. Clean the interior as recommended
under “CLEANING AND CARE.”
4. Insert the plug into the wall socket
and switch on the electricity supply.
• When the door is open the fridge
interior light will come on.
5. You will hear a noise as the
compressor starts up. The liquid and
gases sealed within the refrigeration
system may also give rise to noise,
whether the compressor is running
or not which is quite normal.“Due
to operation of the fan inside the
frost free freezer compartment,
overall noise level is slightly higher
in comparison to non-frost free
appliances. This is quite normal and
is not a fault.”
16
6. Set the thermostat half way between
1 and 5.
7. Front edges of the cabinet may feel
warm. This is normal. These areas
are designed to be warm to avoid
condensation.
8. “Do not load the appliance
immediately it is switched on. Wait
until the correct storage temperature has been reached.
We recommend that you check
the temperature with an accurate
thermometer (see; Temperature
Control and Adjustment)”
EN
5 Using your refrigerator
Temperature Control And Adjustment
Operating temperatures are controlled
by the thermostat (see diagram) located
on the ceiling of fridge compartment.
Settings may be made from 1 to 5, 5
being the coldest position.
When the appliance is switched on
for the first time, the thermostat should
be adjusted so that after 24 hours, the
average fridge temperature is no higher
than +5°C (+41°F). We recommend you
set the thermostat half way between
the 1 and 5 setting and monitor to
obtain the desired temperature i. e.
towards 5 you will obtain a colder fridge
temperature and vice versa. Some
sections of the fridge may be cooler or
warmer ( such as the salad crisper and
the top part of the cabinet ) which is
quite normal.
The normal storage temperature of the
freezer should be -18°C (0°F). Lower
temperatures may be obtained by
adjusting the thermostat towards 5
position.
17
We recommend that you check
the temperature with an accurate
thermometer to ensure that the storage
compartments are kept to the desired
temperature.
Remember you must take your reading
very quickly since the thermometer
temperature will rise very rapidly after
you remove it from the freezer.
Please remember each time the door
is opened cold air escapes and the
internal temperature rises. Therefore
never leave the door open and ensure
it is closed immediately after food is put
in or removed.
In case of a temporary ice build up
in the fridge compartment, reduce the
thermostat setting to 1, monitoring
at the same time that the fridge
temperature is maximum +5 degrees
C [41 degrees F]. Once the ice build
up disappears and the appliance
starts auto defrosting again as normal,
then you may increase the thermostat
setting, if required.
EN
Suggested Arrangement Of
Food In The Fridge/Freezer
1
2
3
7
9
10
8
4
6
5
5
Arrangement Examples (See diagram)
1. Baked, chilled cooked food, dairy
products, cans.
2. Meat, sausages, cold cuts.
3. Fruit, vegetables, salads.
4. Making, storing ice cubes.
5. Frozen food.
6. Frozen food and freezing of fresh
food.
7. Butter, cheese.
8. Small bottles, cans, tubes.
9. Eggs
10.Water dispenser
18
The
following
guidelines
and
recommendations are suggested to
obtain the best
results and storage hygiene.
1. The fridge compartment is for the
short term storage of fresh food and
drinks.
2. The freezer compartment is
rated and suitable for the freezing
and storage of pre frozen food. The
recommendation for
storage
as stated on the food packaging
should be observed at all times.
3. Cooked dishes must be stored in
airtight covered containers.
4. Fresh wrapped produce can be
placed on the shelf. Fresh fruit and
vegetables should be cleaned and
stored in the crisper bins.
5. Bottles can be placed in the door
section.
6. To store raw meat, wrap in polythene
bags and place on the lowest
shelf. Do not allow to come into
contact with cooked food to avoid
contamination. For safety, only store
raw meat for two to three days.
7. Keep the food packed wrapped
or covered. Allow hot food and
beverages to cool before placing
them in the fridge. Do not store
explosive substances. High proof
alcohol must be stored upright in
sealed containers. Left over canned
food should not be stored in the can.
8. Fizzy drinks should not be frozen and
products such as flavoured water
ices should not be consumed too
cold.
EN
9. Some fruit and vegetables suffer
damage if kept at temperatures near
0°C. Therefore wrap pineapples,
melons, cucumbers, tomatoes and
similar produce in polythene bags.
10. Place chilled cooked food and similar
food near the rear of the fridge inner
liner where the cold wall is located.
11.Shelves, racks, crisper bins,
drawers, flaps, bottle grippers are all
removable.
12.Do not leave frozen food at room
temperature to thaw; the best way to
defrost food is to put it in the fridge
to thaw slowly. Make sure you avoid
defrosting food or food juices drip
onto other food.
13.For hygiene reasons, always wrap
food using a suitable packaging
material before storing in your
appliance to avoid contact with the
appliance surface.
Storing Frozen Food
Prepacked commercially frozen food
should be stored in accordance with
the
frozen food manufacturer’s instructions
for a
frozen food storage
compartment.
To ensure that the high quality achieved
by the frozen food manufacturer and
the
food retailer is maintained, the
following should be remembered:
1. Put packets in the freezer as quickly
as possible after purchase.
2. Ensure that contents are labelled and
dated.
3. Do not exceed “Use By”, “Best
Before” dates on the packaging.
19
If there is a power failure do not open
the door. Frozen food should not be
affected if the failure lasts for less than
13 hrs. If the failure is longer, then the
food should be checked and either
eaten immediately or cooked and then
re-frozen.
Freezing Fresh Food
Please
observe
the
following
instructions to obtain the best results.
Do not freeze too large a quantity at
any one time. The quality of the food
is best preserved when it is frozen
right through to the core as quickly as
possible.
Placing warm food into the freezer
compartment causes the refrigeration
compressor to operate continuously
until the food is frozen solid. This can
temporarily lead to excessive cooling of
the refrigeration compartment.
When freezing fresh food turn the
setting towards. Max small quantities of
food up to 1/2 kg. (1 lb) can be frozen
without having to rotate the temperature
control.
You may place fresh food to be frozen
in any part of the freezer.
Take special care not to mix already
frozen food and fresh food.
Making Ice Cubes
Fill the ice - cube tray 3/4 full with
water and place it in the Ice Bank.
Loosen frozen trays with the handle of a
spoon, never use sharp edged objects
such as knives, forks. Store ice-cubes
in the Ice Bank.
EN
Note: If freshly made ice cubes are
not consumed for several weeks and
stored in Ice Bank, they will slowly
reduce in size and eventually disappear
completely.
Defrosting
A) Fridge Compartment
The fridge compartment defrosts
automatically. The defrosting water
runs to the drain tube via a collection
container at the back of the appliance
(1).(see diagram) During defrosting
water droplets may form at the back of
the fridge compartment
where concealed evaporator is
located.Some droplets may remain on
the liner and refreeze when defrosting is
completed. Do not use pointed or sharp
edged objects such as knives, forks to
remove the droplets which have frozen.
If at any time the defrost water does
not drain from the collection channel,
check to ensure that no food particles
have blocked the drain tube. The drain
tube can be cleared by pushing the
special plastic plunger provided down
the drain tube (2). If the frost layer
reaches about 1/4”(7 mm), reduce
the setting (i.e. from 4 to 1) to restart
automatic defrosting.
20
B) Freezer Compartment
The freezer compartment defrosts
automatically.
Warnings!
The fan inside the freezer compartment
circulates cold air. Never insert
any object through the guard. Do not
allow children to play with
the freezer fan.
Never store products that contain
inflammable propellant gas
(eg dispensers, spray cans etc.) or
explosive substances.
Don’t cover the shelves with any
protective materials, which may
obstruct air circulation.
Do not allow children to play with the
appliance or tamper with the controls.
Do not obstruct the freezer fan
guard to ensure that you obtain the
best possible performance from your
appliance.
EN
Water Dispenser
*optional
The water dispenser is a very useful
feature allowing cold water on tap
without opening the door of your
refrigerator .As you will not have to
open your refrigerator door frequently,
you will have saved energy.
As the level of the water in your glass/
container rises, slightly lessen the
pressure on the arm to prevent the
overspill. If you slightly press the arm,
the water will drip; this is quite normal
and not a failure.
Filling the water dispenser's tank
Open the cover of the water tank as
shown in the figure. Fill in the pure and
clean drinking water. Close the cover.
To avoid flowing of water by mistake,
we recommend you to lock the water
dispenser .
Using the water dispenser
Push the arm of the water dispenser
with your glass. The dispenser will
cease operating once you release the
arm.
When operating the water dispenser,
maximum flow can be obtained by
pressing the arm fully. Please remember
that the amount of flow from the
dispenser is subject to the degree you
press the arm.
21
Warning!
• Do not fill the water tank with any
other liquid except for water such as
fruit juices, carbonated beverages
or alcoholic drinks which are not
suitable to use in the water dispenser.
Water dispenser will be irreparably
damaged if these kinds of liquids are
used. Warranty does not cover such
usages. Some chemical substances
and additives contained in these
kinds of drinks/liquids may damage
the water tank.
• Use clean and pure drinking water
only.
EN
• Capacity of the water tank is 2.2
Litres (3.8 pints); do not overfill.
• Push the arm of the water dispenser
with a rigid glass. If you are using
disposable plastic glasses, push the
arm with your fingers from behind the
glass.
1
2
1
Cleaning the water tank
Release the tank cover from the water
tank by opening latches at both sides.
Remove the water tank and clean with
warm and clean water. Place the water
tank to its seating, install the tank cover
and close the latches.
3
22
Make sure that the parts removed
(if any) during cleaning are properly
attached to their original places.
Otherwise, water leakage may occur.
Important:
Components of the water tank and
water dispenser should not be washed
in dishwasher.
Water tray
Water that dripped while using the
water dispenser accumulates in the
spillage tray. Take out the spillage tray
by pulling it towards yourself and empty
it regularly.
Take out the plastic strainer by
pressing it on sides.
Take the water valve out of the water
tank. When replacing it, make sure that
the seal is in place.
EN
6 Maintenance and cleaning
Protection of plastic
surfaces
ANever use gasoline, benzene or
similar substances for cleaning
purposes.
BWe recommend that you unplug the
C Do not put the liquid oils or oil-cooked
meals in your refrigerator in unsealed
containers as they damage the
plastic surfaces of your refrigerator. In
case of spilling or smearing oil on the
plastic surfaces, clean and rinse the
relevant part of the surface at once
with warm water.
appliance before cleaning.
BNever use any sharp abrasive
instrument, soap, household
cleaner, detergent and wax polish for
cleaning.
C Use lukewarm water to clean the
cabinet of your refrigerator and wipe it
dry.
C Use a damp cloth wrung out in
a solution of one teaspoon of
bicarbonate of soda to one pint of
water to clean the interior and wipe it
dry.
BMake sure that no water enters the
lamp housing and other electrical
items.
BIf your refrigerator is not going to be
used for a long period of time, unplug
the power cable, remove all food,
clean it and leave the door ajar.
C Check door seals regularly to ensure
they are clean and free from food
particles.
ATo remove door racks, remove all the
contents and then simply push the
door rack upwards from the base.
ANever use cleaning agents or water
that contain chlorine to clean the
outer surfaces and chromium coated
parts of the product. Chlorine causes
corrosion on such metal surfaces.
23
EN
7 Recommended solutions for the problems
Please review this list before calling the service. It might save you time and
money. This list includes frequent complaints that are not arising from defective
workmanship or material usage. Some of the features described here may not
exist in your product.
The refrigerator does not operate.
• Is the refrigerator properly plugged in? Insert the plug to the wall socket.
• Is the fuse of the socket which your refrigerator is connected to or the main fuse
blown out? Check the fuse.
Condensation on the side wall of the fridge compartment (MULTIZONE, COOL
CONTROL and FLEXI ZONE).
• Very cold ambient conditions. Frequent opening and closing of the door. Highly
humid ambient conditions. Storage of food containing liquid in open containers.
Leaving the door ajar. Switching the thermostat to a colder degree.
• Decreasing the time the door left open or using it less frequently.
• Covering the food stored in open containers with a suitable material.
• Wipe the condensation using a dry cloth and check if it persists.
Compressor is not running
• Protective thermic of the compressor will blow out during sudden power
failures or plug-out plug-ins as the refrigerant pressure in the cooling system of
the refrigerator has not been balanced yet. Your refrigerator will start running
approximately after 6 minutes. Please call the service if the refrigerator does not
startup at the end of this period.
• The fridge is in defrost cycle. This is normal for a full-automatically defrosting
refrigerator. Defrosting cycle occurs periodically.
• Your refrigerator is not plugged into the socket. Make sure that the plug is
properly fit into the socket.
• Are the temperature adjustments correctly made?
• Power might be cut off.
24
EN
The fridge is running frequently or for a long time.
• Your new product may be wider than the previous one. This is quite normal.
Large refrigerators operate for a longer period of time.
• The ambient room temperature may be high. This is quite normal.
• The refrigerator might have been plugged in recently or might have been loaded
with food. Cooling down of the refrigerator completely may last for a couple of
hours longer.
• Large amounts of hot food might have been put in the refrigerator recently. Hot
food causes longer running of the refrigerator until they reach the safe storage
temperature.
• Doors might have been opened frequently or left ajar for a long time. The warm
air that has entered into the refrigerator causes the refrigerator to run for longer
periods. Open the doors less frequently.
• Freezer or fridge compartment door might have been left ajar. Check if the doors
are tightly closed.
• The refrigerator is adjusted to a very low temperature. Adjust the refrigerator
temperature to a warmer degree and wait until the temperature is achieved.
• Door seal of the fridge or freezer may be soiled, worn out, broken or not properly
seated. Clean or replace the seal. Damaged/broken seal causes the refrigerator
to run for a longer period of time in order to maintain the current temperature.
Freezer temperature is very low while the fridge temperature is sufficient.
• The freezer temperature is adjusted to a very low temperature. Adjust the freezer
temperature to a warmer degree and check.
Fridge temperature is very low while the freezer temperature is sufficient.
• The fridge temperature might have been adjusted to a very low temperature.
Adjust the fridge temperature to a warmer degree and check.
Food kept in the fridge compartment drawers are freezing.
• The fridge temperature might have been adjusted to a very low temperature.
Adjust the fridge temperature to a warmer degree and check.
25
EN
Temperature in the fridge or freezer is very high.
• The fridge temperature might have been adjusted to a very high degree.
Fridge adjustment has an effect on the temperature of the freezer. Change
the temperature of the fridge or freezer until the fridge or freezer temperature
reaches to a sufficient level.
• Doors might have been opened frequently or left ajar for a long time; open them
less frequently.
• Door might have been left ajar; close the door completely.
• Large amount of hot food might have been put in the refrigerator recently. Wait
until the fridge or freezer reaches the desired temperature.
• The refrigerator might have been plugged in recently. Cooling down of the
refrigerator completely takes time.
The operation noise increases when the refrigerator is running.
• The operating performance of the refrigerator may change due to the changes in
the ambient temperature. It is normal and not a fault.
Vibrations or noise.
• The floor is not even or it is weak. The refrigerator rocks when moved slowly.
Make sure that the floor is strong enough to carry the refrigerator, and level.
• The noise may be caused by the items put onto the refrigerator. Items on top of
the refrigerator should be removed.
There are noises coming from the refrigerator like liquid spilling or spraying.
• Liquid and gas flows happen in accordance with the operating principles of your
refrigerator. It is normal and not a fault.
There is a noise like wind blowing.
• Fans are used in order to cool the refrigerator. It is normal and not a fault.
Condensation on the inner walls of refrigerator.
• Hot and humid weather increases icing and condensation. It is normal and not a
fault.
• Doors might have been left ajar; make sure that the doors are closed fully.
• Doors might have been opened frequently or left ajar for a long time; open them
less frequently.
Humidity occurs on the outside of the refrigerator or between the doors.
• There might be humidity in the air; this is quite normal in humid weather. When
the humidity is less, condensation will disappear.
26
EN
Bad odour inside the refrigerator.
• Inside of the refrigerator must be cleaned. Clean the inside of the refrigerator with
a sponge, lukewarm water or carbonated water.
• Some containers or package materials might cause the smell. Use a different
container or different brand packaging material.
The door is not closing.
• Food packages may prevent the door's closing. Replace the packages that are
obstructing the door.
• The refrigerator is not completely upright on the floor and rocking when slightly
moved. Adjust the elevation screws.
• The floor is not level or strong. Make sure that the floor is level and capable to
carry the refrigerator.
Crispers are stuck.
• The food might be touching the ceiling of the drawer. Rearrange food in the
drawer.
27
EN
8 Guarantee Details
GUARANTEE DETAILS
Your new Beko product is guaranteed against the cost of breakdown repair for
twelve months from the date of the original purchase.
What is covered?
• Repairs necessary as a result of faulty materials, defective components or
manufacturing defect.
• The cost of functional replacement parts, but excluding consumable items.
• The labour costs of a Beko approved repairer to carry out the repair.
What is not covered?
• Transit, delivery or accidental damage or misuse and abuse.
• Cabinet or appearance parts, including control knobs, flaps, handles or
container lids.
• Accessories or consumable items including but not limited to, ice trays,
scrapers, cutlery baskets, filters and light bulbs.
• Repairs required as a result of unauthorised repair or inexpert installation that
fails to meet the requirements contained in the user instruction book.
• Repairs to products used on commercial or non-residential household
premises.
• Loss of frozen food in freezers or fridge/freezers. (Food loss insurance is
often included within your household contents insurance policy, or may be
available separately from your retailer).
Important notes.
• Your Beko product is designed and built for domestic household use only.
• The guarantee will be void if the product is installed or used in commercial
or non-residential domestic household premises.
• The product must be correctly installed, located and operated in accordance
with the instructions contained in the User Instructions Booklet provided.
• Professional installation by a qualified Electrical Domestic Appliance Installer
is recommended for all Washing Machines, Dishwashers and Electric Cookers
• Gas Cookers must only be installed by a Gas Safe (or BORD GAIS) registered
Gas Installer.
• The guarantee is given only within the boundaries of the United Kingdom
and the Republic of Ireland.
• The guarantee is applicable only to new products and is not transferable if
the product is resold.
• Beko disclaims any liability for incidental or consequential damages.
The guarantee does not in anyway diminish your statutory or legal rights.
28
EN
9 How To Obtain Service
HOW TO OBTAIN SERVICE
Please keep your purchase receipt or other proof of purchase in a safe
place; you will need to have it should the product require attention under
guarantee.
You should also complete the details below; it will help us assist you when
requesting service. (The model number is printed on the Instruction Booklet and
the serial number is printed on the Rating Label affixed to the appliance)
Model No:
Serial No:
Retailer:
Date of purchase:
For service under guarantee simply telephone the appropriate number
below
UK Mainland & Northern Ireland
Fridges & Freezers
Electric Cookers
Gas & Dual Fuel Cookers
Washing Machines
& Dishwashers
0845 6004903
0845 6004902
0845 6004905
0845 6004906
Republic of Ireland
All Refrigeration, All Cookers
Washing Machines & Dishwashers
01 862 3411
Before requesting service please check the trouble-shooting guide in
the Operating Instructions as a charge may be levied where no fault is
found even though your product may still be under guarantee.
Service once the manufacturers guarantee has expired.
If you have purchased an extended guarantee please refer to the instructions
contained within the extended guarantee agreement document. Otherwise
please call the appropriate number above where service can be obtained at a
charge.
Should you experience any difficulty in obtaining service please contact the Beko
Customer Help-Line.
Tel: 0845 6004911 e-mail: service@beko.co.uk
BEKO plc
Beko House
Caxton Way
Watford
Hertfordshire
WD18 8UF
Tel: 0845 6004911
Fax: 0845 6004922
e-mail: service@beko.co.uk
website: www.beko.co.uk
Printed in Turkey
Part no: 573133 0000
Revision no: AD
Download PDF

advertising