Beko DRVS 62 W Clothes Dryer User Manual

Room Air Conditioner
Models :
LG-BKE 4450 D - LG-BKE 5455 D
LG-BKE 4500 D - LG-BKE 5505 D
LG-BKE 4600 D - LG-BKE 5605 D
LG-BKE 4700 D - LG-BKE 4800 D
OWNER'S MANUAL
• Please read carefully and thoroughly this
manual before operating this unit.
• Contact the authorized SVC man for repair or
maintenance of this unit.
• Contact the installer for installation of this unit.
• The appliance is not intended for use by young
children or infirm persons without supervision.
• Young children should be supervised to ensure
that they do not play with the appliance.
Prior to installation, this air-conditioning
unit must be submitted for approval by the
utility service which provides electricity
(EN 6055-3 Norm).
Safety Precautions
Operating Instructions
Care and Maintenance
Troubleshooting Tips
Safety precautions
Safety Precautions
Warning ................................2
Caution .................................3
Operating Instructions
Preparation before operation ..4
About the Remote Control on
the System............................5
Operation Mode Selection
Button....................................6
To prevent injury to the user or other people and property damage, the
following instructions must be followed.
■ Incorrect operation due to ignoring of instruction will cause harm or
damage, the seriousness is classified by the following indications.
WARNING
WARNING
This symbol indicates the possibility of death or serious injury.
CAUTION
CAUTION
This symbol indicates the possibility of injury or damage to
properties only.
Installation precautions
Care and Maintenance
Care and Maintenance .......13
Operation Tips ....................14
Troubleshooting tips
Before You
Call For Service ...............15
WARNING
WARNING
■ Do not install, remove and reinstall the unit by yourself.
• Improper installation will cause water leakage, electrical
shock, or fire. Please consult authorized dealer or specialist
for the installation work. Please note fault caused by
improper installation is not covered by warranty.
• Unit must be installed in an easily accessible area. Any
additional cost required to hire a special equipment to
service the unit will be the responsibility of the customer.
WARNING
WARNING
Plug in the power plug
properly.
Do not operate or stop the
unit by inserting or pulling
out the power plug.
Do not damage or use an
unspecified power cord.
• Otherwise, it will cause
electrical shock or fire due to
heat generation.
• It will cause electrical shock
or fire due to heat
generation.
• It will cause electrical shock or fire.
Do not operate with wet
hand.
Do not insert anything into the
air inlet/air outlet.
• It will cause electrical shock
or fire due to heat
generation.
• It may cause electrical
shock.
• Since the fan rotates at high
speed, this may cause an
injury or damage the unit.
Do not expose the skin
directly to cool air for long
periods of time.
When an abnormality (smell of burning, etc)
occurs, stop the air conditioner, and disconnect
the power plug or turn off the breaker.
Repair or relocation should
not be done by the
customer.
• This could damage your
health.
• If the unit continues to be operated
in an abnormal condition, it may
cause a fire, damage, etc. In this
case, consult your dealer.
• If this is done incorrectly, it may
cause a fire, electric shock, injury
by dropping of the unit, water
leakage, etc. Consult your dealer.
Do not modify power cord
length or share the outlet
with other appliances.
2
• If the supply cord is damaged, it
must be replaced by the
manufacturer or its service agent
or a similarly qualified person in
order to avoid a hazard.
• Contact the authorized Service technician for repair or maintenance of this unit.
• Contact the installer for installation of this unit.
• The air conditioner is not intended for use by young children or infirm persons
without supervision.
• Young children should be supervised to ensure that they do not play with the air
conditioner.
Safety Precautions
CAUTION
CAUTION
CAUTION
• It may cause an injury.
Do not clean the air
conditioner with water.
• Should be disconnected from
supply
• Water may enter the unit and
degrade the insulation. It may
cause an electric shock.
When the unit is to be
cleaned, switch off, and turn
off the circuit breaker.
Do not put a pet or house
plant where it will be
exposed to direct air flow.
Do not apply an insecticide
or flammable spray.
• This could injure the pet or
plant.
Do not put a stove, etc.
where is exposed to direct
air flow.
• It may cause a fire or
deformation of the cabinet.
• It may affect combustion.
Do not insert hands through
vanes when the air conditioner
is operationg
When the unit is not going to
be used for a long time, turn
off the circuit breaker.
• It will cause an injury by the
rotating blower.
• Do not use this air conditioner
to preserve precision devices,
food, animal, plants, and art
objects.
It may cause deterioration of
quality, etc.
Do not operate for a long time in
high humidity, e.g. leaving a
door or window open.
• In the cooling mode, if it is
operated in a room with high
humidity (80%RH or more) for
a long time, water condensed
in the air conditioner may drop
and may wet and spoil
furniture, etc.
3
Do not leave on installation
stand which is damaged.
• The unit may drop or fall
down and cause an injury.
Do not step on the
indoor/outdoor unit and do
not put anything on it.
• It may cause an injury
through dropping or falling
down.
Do not step onto an unstable
bench when cleaning and/or
maintaining the unit.
• It may cause an injury, etc.
by falling down.
Troubleshooting Tips
Do not use for special
purposes.
• If not, dirt may collect and
cause a fire.
• An oxygen shortage may
occur.
Care and Maintenance
• Since the fan rotates at high
speed during operation, it
may cause an injury.
Ventilate well when used
together with a stove, etc.
Operating Instructions
When the air filter is to be
removed, do not touch the
metal parts of the indoor unit.
Safety Precautions
Operating Instructions
Care and Maintenance
Troubleshooting Tips
Preparation before operation
How to Insert the Batteries
Remove the battery cover by pulling it according to the
arrow direction.
Insert new batteries making sure that the (+) and (-) of
battery are installed correctly.
Reattach the cover by sliding it back into position.
NOTES:
• Use 2 AAA(1.5volt) batteries. Do not use rechargeable
batteries.
Storage and Tips For Using the Remote Control
• The remote control may be stored mounted on a
wall.
• To operate the room air conditioner, aim the
remote control at the signal receptor.
Signal Receptor
Receives the signals from the remote controller.
(Signal receiving sound:two short beeps or one long beep.)
Operation Indication Lamps
On/Off
: Lights up during the system operation.
OFF Timer
:Lights up during indoor unit operation.
ON Indoor Unit :Lights up during indoor unit operation.
Operation
Defrost Mode : Lights up during Defrost Mode or Hot Start operation.
(Heat pump model only)
Signal
receptor
Operation indication lamps
4
Features of the Remote Control
Remote Controller
1
Signal transmitter
2
Transmits the signals to the room air
conditioner.
OPERATION DISPLAY
Displays the operation conditions.
OPERATION MODE SELECTION
BUTTON
Used to select the operation mode.
1
4
OFF TIMER BUTTON
Used to set the time of stopping operation.
3
4
5
8
2
7
5
TEMP.
OFF
TIME
hr.
6
START/STOP BUTTON
Operation starts when this button is
pressed, and stops when the button is
pressed again.
6
ROOM TEMPERATURE SETTING
BUTTONS
7
INDOOR FAN SPEED SELECTION
BUTTON
8
JET COOL
Used to start or stop the speed cooling.
(Speed cooling operates super high fan
speed in cooling mode.)
Care and Maintenance
3
Operating Instructions
AIRFLOW DIRECTION START/STOP
BUTTON
Used to stop or start louver movement and
set the desired up/down airflow direction.
Safety Precautions
About the remote control on the system
Troubleshooting Tips
5
Safety Precautions
Operation Mode Selection button
Features of the Remote Control
(1) OPERATION MODE
Troubleshooting Tips
Care and Maintenance
Operating Instructions
Cooling Operation
Cooling Operation
Healthy Dehumidifacation Operation
Healthy Dehumidifacation Operation
Heating Operation
(Cooling Model)
(Heat pump Model)
(2) OPERATION PROCEDURE
1st
Start/Stop Button
TEMP.
OFF
2nd
Operation Mode Selection
Button
3rd
Room Temperature
Setting Button
4th
TIME
hr.
2
4
1
3
Indoor Fan Speed
Selection Button
6
1
Press the Start/Stop Button.
p
, Bee
Beep
Select Cooling Operation.
Press the Operation Mode Selection Button.
Each time the button is pressed, the operation mode is shifted in the arrow direction.
TEMP.
TEMP.
OFF
OFF
TIME
TIME
OFF
hr.
Cooling
hr.
TEMP.
TIME
TEMP.
OFF
hr.
Healthy
Dehumidification
TIME
hr.
Heating
(Heat pump model only)
TEMP.
OFF
TIME
TEMP.
OFF
hr.
hr.
Set the temperature lower than the room temperature.
• The temperature can be set within a range of 18°C ~ 30°C
by 1°C .
To raise the temperature
TEMP.
OFF
TIME
hr.
To lower the temperature
4
Set the fan speed.
• Select the fan speed in four steps-low, medium, high or CHAOS.
• Each time the button is pressed, the fan speed mode is shifted.
• The display shows high fan speed.
OFF
TIME
hr.
Natural wind by the CHAOS logic
❏ For more fresh feeling than other fan speed, press the Indoor Fan Speed Selector and set to
CHAOS mode. In this mode, the wind blows like natural breeze by automatically changing fan
speed according to the CHAOS logic.
7
Troubleshooting Tips
TEMP.
Care and Maintenance
3
TIME
Healthy
Dehumidification
Cooling
Operating Instructions
2
Safety Precautions
Cooling Operation
Safety Precautions
Healthy Dehumidification Operation Mode
This mode dehumidifies without overcooling.
1
Press the Start/Stop Button.
p
, Bee
Operating Instructions
Beep
OFF
TIME
hr.
2
Select Healthy Dehumidification Operation.
Press the operation Mode Selection Button.
Each time the button is pressed, the operation mode is
shifted in the arrow direction.
TEMP.
Troubleshooting Tips
Care and Maintenance
OFF
TIME
TEMP.
OFF
hr.
Cooling
TIME
hr.
Healthy
Dehumidification
TEMP.
OFF
TIME
hr.
Heating
(Heat pump model only)
TEMP.
OFF
TIME
hr.
Cooling
3
TEMP.
OFF
TIME
hr.
Healthy
Dehumidification
You can select the fan speed in four steps-low,
medium, high, or CHAOS. Each time the button is
pressed, the fan speed mode is shifted.
During Healthy Dehumidification Operation:
❏ If you select the dehumidification mode on the operation selection button, the airconditioner starts to
run the dehumidification function, automatically setting the room temp. and airflow volume to the best
condition for dehumidification based on the sensed current room temp.
In this case, however, the setting temp. is not displayed in the remote control and you are not able to
control the room temp. either.
❏ During the healthy dehumidification function, the airflow volume is automatically set according to the
optimization algorithm responding to the current room temp. status and makes the room condition
healthy and comfortable even in the high humidity season.
8
Press the Start/Stop button.
The unit will respond with
a beep.
2
To select Heating Operation, press the Operation Mode
Selection button.
Each time the button is pressed, the operation mode is
shifted in the direction of the arrow.
TEMP.
OFFTIME
TIME
hr.
hr.
TEMP.
OFF
TIME
hr.
Cooling
3
TEMP.
OFF
TIME
TEMP.
OFF
hr.
Healthy
Dehumidification
TIME
hr.
Heating
(Heat pump model only)
Set the temperature higher than the room temperature.
The temperature can be set within a range of 16°C~30°C in
1°C increments.
TEMP.
TIME
To raise the temperature
hr.
To lower the temperature
4
Set the fan speed again with the door of the
remote control still closed. You can select
the fan speed in four steps–low, medium,
high, or CHAOS. Each time the button is
pressed, the fan speed mode is shifted.
OFF Timer control Setting
Press the OFF Time Button.
TEMP.
OFF
TIME
p
, Bee
Beep
hr.
1. Press the OFF Time Button.
2. Check the OFF Time LED of the room air conditioner.
3. The Timer is programmed by 1 hour each
pressing the OFF Time button from 1 hour to 7 hours.
9
Troubleshooting Tips
OFF TIMER CONTROL SETTING
Care and Maintenance
OFF
Operating Instructions
1
Safety Precautions
Heating Operation(Heat pump model only)
TEMP.
OFFTIME
TIME
Safety Precautions
Troubleshooting Tips
Care and Maintenance
Operating Instructions
Jet Cool Operation
1
Press the Start/Stop button.
The unit will respond with a beep.
2
Press the Jet Cool button to operate the
speed cooling mode and the unit will
operate in super high fan speed on cooling
mode for 30 minutes.
3
To cancel the Jet Cool mode, press the Jet Cool button
again or the fan speed button or the room temperature
setting button and the unit will operate in high fan speed on
cooling mode.
hr.
hr.
or
or
or
NOTE:
❏ During the JET COOL function at any moment, the A/C starts to blow the cool air at
extremely high speed for 30 minutes setting the room temp. automatically to 18°C. It is
especially used to cool the room temp. in the shortest time in a hot summer.
In heat pump mode the JET COOL function is not available.
❏ In order to return to the normal cooling mode from the JET COOL mode, you just press
either the operation mode selection button, airflow volume selection or temp. setting button
or the JET COOL button again.
10
Airflow Direction Control
The airflow direction can be adjusted as desired by
using the remote controller. This is effective when you
want to cool yourself directly, such as after taking a
bath.
2
Press the Airflow Direction Control
Button and the vertical louvers swing up
and down automatically.
3
Press again the Airflow Direction
Control Button to set the vertical louver
at the desired airflow direction.
Horizontal Airflow Direction Control (Optional)
• Adjust the horizontal airflow direction by manually
moving the horizontal airflow direction louver by
hand.
11
Troubleshooting Tips
Caution
• Always use the remote controller to adjust
the airflow direction. Manually moving the
vertical airflow direction louver by hand could
cause operation errors.
• When air conditioner operation is stopped,
the vertical airflow direction louver will close
the air outlet vent of room air conditioner.
Care and Maintenance
Press the Start/Stop Button.
(Confirm the unit on operation.)
Operating Instructions
1
Safety Precautions
Airflow Direction Procedure
Safety Precautions
Operating Instructions
Care and Maintenance
Troubleshooting Tips
Forced Operation
Operation procedures when the remote
control can't be used.
The operation will be started if the power
button is pressed.
If you want to stop operation, re-press
the button.
Power
button
Open the front
panel upward
Cooling Model
Operating mode
Indoor FAN Speed
Setting Temperature
Cooling
High
22°C
Room Temp. 24°C
Cooling
High
22°C
Heat pump Model
21°C Room Temp. < 24°C
Healthy Dehumidification
High
23°C
Room Temp. < 21°C
Heating
High
24°C
Test operation
During the TEST OPERATION, the unit operates in cooling mode at high speed fan, regardless of
room temperature and resets in 18 minutes.
During test operation, if remote controller signal is received, the unit operates as remote controller sets.
If you want to use this operation, open the front panel upward and Press the power button let it be
pressed for about 3 seconds.
If you want to stop the operation, re-press the button.
Auto restart
In case the power comes on again after a power failure, Auto Restarting Operation is the function to
operate procedures automatically to the previous operating conditions.
So there is no need of activating this function by pressing any key or button.
In the initial mode, the fan operates at a low speed and the compressor starts 2.5~3 minutes later.
As the compressor starts, the fan speed also resumes its previous setting mode.
Additionally, in order to cancel auto restart operation press power button let it be pressed for about
6 seconds. To operate auto restart operation again, press power button for about 6 seconds as well.
Helpful information
Fan speed and cooling capacity.
The cooling capacity indicated in the specification is the
value when the fan speed is set to high, and the capacity will
be lower at low or medium fan speed.
High fan speed is recommended when you wish to cool the
room quickly.
12
h
Hig ed
e
Sp
CAUTION: Before performing any maintenance, turn off the main power to the system.
Indoor Unit
Grille, Case, and Remote Control
❏ Turn the system off before cleaning. To
clean, wipe with a soft, dry cloth. Do not
use bleach or abrasives.
NOTE:
Supply power must be disconnected before
cleaning the indoor unit.
❏ Never use any of the followings:
• Water hotter than 40°C
Could cause deformation and/or
discoloration.
• Volatile substances
Could damage the surfaces of the air
conditioner.
d er
G a s o li n e
AIR FILTERS
1 Lift the front access panel and pull the filter tab
slightly forward to remove the filter.
The air filters behind the front grille should be
checked and cleaned once every 2 weeks or
more often if neccessary.
2 Clean the filter with a vacuum or warm, soapy
3 After washing with water, dry well in the
shade.
4 Re-install the air filter.
Outdoor Unit
Air intake
vents
NOTE:
Dirty or clogged coils will reduce the
operating efficiency of the system
Air outlet
and cause higher operating costs.
vents
13
(Rear)
(Side)
Piping
Drain Hose
Troubleshooting Tips
The heat exchanger coils and panel vents of the
outdoor unit should be checked regularly. If
clogged with dirt or soot, the heat exchanger
and panel vents may be professionally steam
cleaned.
Care and Maintenance
water.
• If dirt is conspicuous, wash with a
solution of detergent in lukewarm water.
• If hot water (40°C or more) is used, it
may be deformed.
Operating Instructions
Pow
Air filters
Air inlet vent Air outlet vent
(behind front panel)
Vertical louver Horizontal louver
Safety Precautions
Care and maintenance of the air conditioner
Safety Precautions
Operating Instructions
Care and Maintenance
Troubleshooting Tips
When the air conditioner is not going to be used for a long time.
When air conditioner is not going to be
used for a long time.
When the air conditioner is to be used again.
Turn off the circuit breaker, and disconnect
the plug.
Clean the air filter and install it in the indoor
unit.
(Refer to page 13 for cleaning filters.)
CAUTION
Turn off the circuit breaker when the air conditioner
is not going to be used for a long time.
Dirt may collect and may cause a fire.
Check that the air inlet and outlet of the
indoor/outdoor unit are not blocked.
Remove the batteries from the remote
control.
Operation Tips
Do not overcool the room.
Keep blinds or curtains
closed.
Keep the room temperature
uniform.
This is not good for the health
and wastes electricity.
Do not let direct sunshine enter
the room when the air
conditioner is in operation.
Adjust the vertical and
horizontal airflow direction to
ensure a uniform temperature
in the room.
Make sure that the doors
and windows are shut tight.
Clean the air filter regularly.
Ventilate the room
occasionally.
Avoid opening doors and
windows as much as possible
to keep the cool air in the room.
Blockages in the air filter
reduce the airflow and lower
cooling and dehumidifying
effects. Clean at least once
every two weeks.
Since windows are kept closed,
it is a good idea to open them
and ventilate the room now and
then.
14
Before you call for service...
Troubleshooting Tips! Save time and money!
Check the following points before requesting repairs or service.... If the fault persists, please
contact your dealer or service center.
Case
Explanation
See page
The air conditioner does not
operate.
• Have you made a mistake in timer operation?
• Has the fuse blown or has the circuit breaker
been tripped?
-
-
It seems that condensation
is leaking from the air
conditioner.
• Condensation occurs when the airflow from
the air conditioner cools the warm room air.
-
Air conditioner does not
operate for about 3 minutes
when restarted.
• This is the protector of the mechanism.
• Wait about three minutes and operation will
begin.
-
Does not cool or heat
effectively.
• Is the air filter dirty? See air filter cleaning
instructions.
• Has the temperature been set incorrectly?
• Are the indoor unit's air inlet or outlet vents
obstructed?
The air conditioner
operation is noisy.
13
7
-
-
Remote control display is
faint, or no display at all.
• Are the batteries depleted?
• Are the batteries inserted in the opposite (+)
and (-) directions?
4
Crack sound is heard.
• This sound is generated by the
expansion/constriction of the front panel, etc.
due to changes of temperature.
-
NOTE
WATER RESISTANT: The outdoor side of this appliance is WATER RESISTANT.
The indoor side is not water resistant and should not be exposed to excess water.
15
Troubleshooting Tips
• For a noise that sounds like water flowing.
-This is the sound of freon flowing inside the
air conditioner unit.
• For a noise that sounds like the compressed
air releasing into atmosphere.
-This is the sound of the dehumidifying water
being processed inside the air conditioning
unit.
Care and Maintenance
• Check that this is not a damp smell exuded by
the walls, carpet, furniture, or cloth items in the
room.
Operating Instructions
The room has a peculiar
odor.
Safety Precautions
?