User manual | Beko DV 7220 X Clothes Dryer User Manual

Dryer
DV 7220 X
Read this manual prior to initial operation of the product!
Dear Customer,
We hope that your product, which has been manufactured in modern facilities and passed through
a strict quality control procedure, will give you very good results.
We advise you to read through this manual carefully before using your product and keep it for
future reference.
This User Manual will
• Help you use your machine in a fast and safe way.
• Read the User Manual before installing and starting your product.
• In particular, follow the instructions related to safety.
• Keep this User Manual within easy reach for future reference.
• Please read all additional documents supplied with your product.
Remember that this User Manual is also applicable for several other models.
Explanation of symbols
Throughout this User Manual the following symbols are used:
B
Important safety information. Warning for hazardous situations with regard to life and property.
Caution; Warning for supply voltage.
Caution; Warning for fire hazard.
Caution; Warning for hot surfaces.
Read the instructions.
C
Useful information. Important information or useful hints about usage.
This appliance’s packaging material is recyclable. Help recycle it and protect the environment
by dropping it off in the municipal receptacles provided for this purpose. Your appliance
also contains a great amount of recyclable material. It is marked with this label to indicate
the used appliances that should not be mixed with other waste. This way, the appliance
recycling organised by your manufacturer will be done under the best possible conditions,
in compliance with European Directive 2002/96/EC on Waste Electrical and Electronic
Equipment. Contact your town hall or your retailer for the used appliance collection points
closest to your home. We thank you doing your part to protect the environment.
2960310534_EN/200911.0926
A
1
Important safety information
This section includes safety information that will
help protection from risks of personal injuries
or materialistic damages. Failure to follow
these instructions shall cause any warranty and
reliability commitment to become void.
General safety
•
• Never place the machine on a carpetcovered floor, otherwise, lack of airflow
beneath the machine may cause electrical
parts to overheat. This will cause problems
with your machine.
• If the power cable or mains plug is
damaged, you must call qualified
electrician for repair.
• The product should not be plugged in
during installation, maintenance and repair
works. Such works should always be made
by the technical service. Manufacturer
shall not be held responsible for damages
arising from processes carried out by any
unauthorised persons.
• Connect the product to a grounded outlet
protected by a fuse of suitable capacity as
stated in the technical specifications table.
• Operate your product at temperatures
between +5°C and +35°C.
• Do not use electrical devices in the
product.
• Do not connect the air exit of the product
to the chimney holes which are used for
the exhaust fumes of the devices operating
with gas or other types of fuel.
• You must provide enough ventilation in
order to prevent gases exiting from devices
operating with other types of fuels including
the naked flame from accumulating in the
room due to the back fire effect.
• Always clean the lint filter before or after
each loading.
• Never operate your dryer without the
lint filter installed.
• Do not allow fibre, dust and dirt
accumulation around the exhaust exit and
at adjacent areas.
• Power cable plug must be within easy
reach after installation.
• Do not use extension cords, multi-plugs
or adaptors to connect the dryer to power
supply in order to decrease the risk of
electric shock.
• Do not make any changes on the plug
supplied with the product. If it is not
compatible with the socket, have a
qualified electrician change the socket with
a suitable one.
• Items cleaned or washed with gasoil/
fuel oil, dry-laundry solvents and other
combustible or explosive materials as
•
•
•
•
•
•
•
•
•
•
•
3 EN
well as the items that are contaminated
or spotted with such materials should not
be dried in the product since they emit
flammable or explosive vapor.
Do not dry items cleaned with industrial
chemicals in the dryer.
Do not dry unwashed items in the dryer.
Items soiled with cooking oils, acetone,
alcohol, fuel oil, kerosene, stain remover,
turpentine, paraffin and paraffin removers
must be washed in hot water with plenty of
detergent before being dried in the dryer.
Garments or pillows bolstered with rubber
foam (latex foam), shower bonnets, water
resistant textiles, materials with rubber
reinforcement and rubber foam pads
should not be dried in the dryer.
Do not use fabric softeners and anti-static
products unless they are recommended by
the manufacturers of the fabric softener or
the product.
Oil-affected items can ignite spontaneously,
especially when exposed to heat sources
such as in a tumble dryer. The items
become warm, causing an oxidation
reaction in the oil. Oxidation creates heat.
If the heat cannot escape, the items can
become hot enough to catch fire. Piling,
stacking or storing oil-affected items can
prevent heat from escaping and so create
a fire hazard.
If it is unavoidable that fabrics that contain
vegetable or cooking oil or have been
contaminated by hair care products be
placed in a tumble dryer they should
first be washed in hot water with extra
detergent - this will reduce, but not
eliminate, the hazard.
This product must be grounded.
Grounding installation decreases the risk of
electric shock by opening a path with low
resistance for the electricity flow in case of
a malfunction or failure. Power cable of this
product is equipped with a conductor and
a grounding plug that allows for grounding
the product. This plug must be installed
appropriately and inserted into a socket
which is grounded in accordance with the
local laws and regulations.
Do not install the product behind a door
with a lock, sliding door or a door that has
a hinge against the hinge of the dryer.
Do not install or leave this product in
places where it will be exposed to outdoor
conditions.
Do not tamper with the controls.
Do not perform any repair or part replacing
procedures on the product even if you
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
know or have the ability to perform unless
it is clearly suggested in the operating
instructions or the published service
manual.
Inside and exhaust duct of the product
must be cleaned by the qualified service
personnel periodically.
Wrong connection of grounding conductor
of the product can cause electric shock. If
you have any suspect about the grounding
connection, have it checked by a qualified
electrician, service representative or service
personnel.
Do not reach into the machine when the
drum is spinning.
Unplug the machine when it is not in use.
Never wash down the appliance with
water! There is the risk of electric shock!
Always disconnect by unplugging from the
mains before cleaning.
Never touch the plug with wet hands.
Never unplug by pulling on the cable,
always pull out by grabbing the plug only.
Do not operate the machine if the power
cable or plug is damaged!
Never attempt to repair the machine
yourself, otherwise, you will be putting your
life and others’ lives in danger.
For malfunctions that cannot be solved by
following the information given in the safety
instructions:
Turn off the machine, disconnect the
power cord and contact an Beko Service.
Do not stop the dryer before the drying
cycle comes to an end unless you
will remove all laundry from the dryer
immediately in order to lay them and
dissipate the heat.
Remove the door of the drying
compartment before decommissioning or
disposing of the product.
The final step of the drying cycle (cooldown cycle) occurs without applying
heat to ensure that the items are left at a
temperature that will not damage them.
Fabric softeners or similar products should
be used as specified by the fabric softener
instructions.
Underwear that contains metal
reinforcements should not be placed in
a dryer. Damage to the dryer can result if
metal reinforcements come loose during
drying.
Check all garments for forgotten lighters,
coins, metal pieces, needles, etc. before
loading.
Remove all objects from pockets such as
lighters and matches.
At times when your dryer is not in use or
after the laundry is taken out following the
completion of drying process, turn off by
using the On/Off button. In cases when
the On/Off button is on (while the dryer
is energized), keep the door of the dryer
closed.
Intended use
• This product has been designed for
domestic use. It should not be used for
other purposes.
• Use the product only for drying laundry that
are marked accordingly.
• Dry only those articles in your product that
are stated in this manual.
• This product is not intended to be used by
persons with physical, sensory or mental
disorders or unlearned or inexperienced
people (including children) unless they
are attended by a person who will be
responsible for their safety or who will
instruct them accordingly for use of the
product.
Children’s safety
• Electrical appliances are dangerous for
the children. Keep children away from the
machine when it is operating. Do not let
them tamper with the machine.
• Packaging materials are dangerous to
children. Keep the packaging materials out
of reach of children or dispose them by
classifying according to waste directives.
• Do not allow children sit/climb on or enter
in the product.
• Children should be supervised to ensure
that they do not play with the product.
• Close the loading door when you leave the
area where the product is located.
4 EN
2 Installation
It is the customers responsibility to arrange a
suitably qualified installer to correctly install this
product.
CPreparation of location and electrical
installation for the product is under
customer’s responsibility.
BInstallation and electrical connections must
be carried out by a qualified personnel.
APrior to installation, visually check if the
product has any defects on it. If so, do not
have it installed. Damaged products will
cause risks for your safety.
placed on top of a washing machine, the
approximate weight of both machines may
reach 180 kg when they are full. Therefore,
the floor must be capable of carrying the
load on it!
Ventilation hose and connection (for
products equipped with an outlet
vent)
Appropriate installation location
• Install the product in an environment which
has no risk of freezing and is in a stable
and level position.
• Operate your product in a well ventilated,
dust-free environment.
• Do not block the air ducts in front of and
under the product with materials such as
long pile rugs and wooden planks.
• Do not place your product on a long pile
rug or on similar surfaces.
• Do not install the product behind a door
with a lock, sliding door or a hinged door
which can strike the product.
• Once the product is installed, it should stay
at the same place where its connections
have been made. When installing the
product, make sure that the rear wall of it
does not touch anywhere (tap, socket, etc.)
and also pay attention to install the product
at a place where it will stay permanently.
BDo not place the product on top of the
power cable.
• Keep at least 1.5 cm distance to walls of
other furniture.
Under counter installation
• A special part (Part no: 295 970 0100)
replacing the top trim must be provided
and installed by the suitably qualified
installer in order to use the machine under
a counter or in a cupboard. It should never
be operated without the top trim.
• Leave at least 3 cm of space between
the side and rear walls of the product and
the walls of the counter/cupboard when
installing your product under a counter or in
a cupboard.
Ventilation hose allows exhaust air from inside
the machine
Vented dryer has 1 air outlet.
Stainless sheet metal or aluminum pipes can
be used instead of a hose. The pipe diameter
should be minimum 10 cm.
Maximum hose and pipe lengths are given in
the table below.
Maximum length
1 elbow 45°
1 elbow 90°
1 elbow 90° short
1 wall passage
Hose
Pipe
4m
-1.0 m
-1.8 m
5m
-0.3 m
-0.6 m
-2.7 m
-2.0 m
-2.0 m
CEach elbow and other passages should
be subtracted from the maximum length
stated above.
To connect a ventilation hose;
1. Connect the air outlet hose to the
hose spacer piece by turning it
counterclockwise.
2. Make the hose passages as shown below.
CExhaust of humid air from the dryer into the
room is inconvenient. It may damage the
walls and furniture in the room.
CThe ventilation hose can be routed outdoors
via a window or it can be connected to the
air outlet in the bathroom.
CAir outlet hose must be routed directly to the
outdoors. There must be a limited number
of elbows as not to hinder ventilation.
CTo prevent water accumulation in the hose,
make sure that it is not folded on the floor.
Mounting over a washing machine
• A fitting device should be used between
the two machines when installing above a
washing machine. The bracket (Part no.
296 280 0100 white/296 280 0200 grey)
must be installed by the Authorised Service
Agent.
• Place the product on a firm floor. If it will be
5 EN
BThe ventilation hose should not be
connected to the chimney of a stove or a
fireplace.
BDo not operate your product at the same
time with heaters such as a coal or gas
stove. Airflow may cause the chimney to
flare up.
Adjusting feet
In order to ensure that your product operates
more silently and vibration-free, it must stand
level and balanced on its feet. Front feet of your
product can be adjusted. Balance the machine
by adjusting the feet.
• Do not make connections via extension
cables or multi-plugs.
• The main fuse and switches must have a
contact distance of minimum 3 mm.
BDamaged power cable must only be
replaced by a qualified electrician.
BIf the product is faulty, it must not be
operated unless it is repaired! There is the
risk of electric shock!
First use
• To have the product ready for operation
before calling the suitably qualified installer,
make sure that its location and power
supply installations are appropriate. If they
are not, call a qualified electrician to have
any necessary arrangements carried out.
• Make sure that the power connections of
the product are in accordance with the
instructions given in relevant chapters of
this manual.
Disposing of packaging material
1. Loosen the feet by hand.
2. Adjust the feet until the product stands level
and firmly on the floor.
CDo not use any tools to loosen the
adjustable feet, otherwise, they can be
damaged.
CNever remove the adjustable feet from their
housings.
2 plastic pieces supplied along with the user
manual prevent your machine from slipping on
wet and slippery surfaces. To install the plastic
parts:
1. Tilt your product to backwards.
2. Fit the plastic parts on to the front
adjustable feet. Press on the plastic parts
to snap them into their seating.
3. Check the balance of your product
again and readjust the adjustable feet if
necessary.
Electrical connection
Connect the machine to a grounded outlet
protected by a fuse of suitable capacity as
stated in the technical specifications table. Our
company shall not be liable for any damages
that will arise when the machine is used on a
circuit without grounding.
• Connection must comply with national
regulations.
• If the current value of the fuse or breaker
in the house is less than 10 Amps, have a
qualified electrician install a 10 Amp fuse.
• Power cable plug must be within easy
reach after installation.
• The voltage and allowed fuse or breaker
protection are specified in the “Technical
Specifications” section.
• The specified voltage must be equal to
your mains voltage.
Packaging materials are dangerous to children.
Keep packaging materials in a safe
place out of reach of children. Packaging
materials of your product are manufactured
from recyclable materials. Sort and dispose
of them in accordance with recycled waste
instructions. Do not dispose of them with
normal domestic waste.
Transportation of the machine
1. Unplug the machine from the mains.
2. Remove the water drain (if any) and
chimney connections.
3. Drain water remaining in the machine
completely before transportation.
Disposing of the old machine
Dispose of your old machine in an
environmentally friendly manner.
Refer to your local dealer or solid waste
collection centre in your area to learn how to
dispose of your machine.
Before disposing of your old machine, cut off
the power cable plug and make the loading
door lock unusable to avoid dangerous
conditions to children.
6 EN
Technical Specifications
EN
2
Height (adjustable)
84,6 cm
Width
59,5 cm
Depth
53 cm
Capacity (max.)
7 kg
Weight (net)
32 kg
Voltage
Rated power input
See type label
Model code
Type label is located behind the loading door.
7 EN
3 Initial preparations for drying
Things to be done for energy saving:
• Make sure that you operate the product
•
•
•
•
•
•
•
•
•
•
•
at its full capacity but pay attention to not
exceeding it.
Spin your laundry at the highest speed
possible when washing them. Thus,
the drying time is shortened and energy
consumption is decreased.
Pay attention to dry same types of laundry
together.
Follow the instructions in the user manual
for programme selection.
Make sure that sufficient clearance is
provided at the front and rear side of the
dryer for air circulation. Do not block the
grill at the front side of the product.
Do not open the door of the machine
during drying unless necessary. If you must
certainly open the door, pay attention not
to keep it open for a long time.
Do not add new (wet) laundry during
drying.
Lint and fibres released from the laundry to
the air during the drying cycle are collected
in the “Lint Filter”. Make sure that you
clean the filters before or after each
drying.
In models with condenser, make sure that
you clean the condenser regularly at
least once every month or after every
30 drying cycles.
In vented models, follow the chimney
connection rules in the user manual and
pay attention to the chimney cleaning.
Ventilate the room, where the dryer is
located, well during drying.
“For power saving in models with lamps, at
times when your dryer is not in use, keep
the door closed if the On/Off button is
pressed (if the dryer is energized).”
Laundry suitable for drying in the
machine
CAlways follow the suggestions on the
laundry labels. Dry only the laundry having
a label stating that they are suitable for
drying in a dryer and make sure that you
select the appropriate programme.
A B C D
Low
l n m
o p q
Laundry unsuitable for drying in the
machine
• Laundry items with metal attachments
such as belt buckles and metal buttons
can damage your dryer.
• Do not dry items such as woollens, silk
garments and nylon stockings, delicate
embroidered fabrics, laundry with metal
accessories and items such as sleeping
bags in the dryer.
• Laundry items made of delicate and
valuable fabrics as well as lace curtains can
be creased. Do not dry them in the dryer!
• Do not dry items made of hermetic fibres
such as pillows and quilts in the dryer.
• Laundry items made of foam or rubber will
be deformed.
• Do not dry laundry items containing rubber
in the dryer.
• Do not dry laundry items exposed to
petroleum, oil, combustible or explosive
agents in the dryer even if they are washed
beforehand.
• Overly wet laundry or laundry with dripping
water must not be put into the dryer.
• Items which are cleaned or washed with
gasoil/fuel oil, dry-laundry solvents and
other combustible or explosive materials
as well as the items that are contaminated
or spotted with such materials should not
be dried in the product since they emit
flammable or explosive vapor.
• Do not dry items cleaned with industrial
chemicals in the dryer.
• Do not dry your unwashed laundry in the
dryer.
• Items soiled with cooking oils, acetone,
alcohol, fuel oil, kerosene, stain remover,
turpentine, paraffin and paraffin removers
must be washed in hot water with plenty of
detergent before being dried in the dryer.
8 EN
• Garments or pillows bolstered with rubber
foam (latex foam), shower bonnets, water
resistant textiles, materials with rubber
reinforcement and rubber foam pads
should not be dried in the dryer.
• Do not use fabric softeners and anti-static
products unless they are recommended by
the manufacturers of the fabric softener or
the product.
• Do not dry the underwear reinforced with
metal parts in the dryer. If these metal
reinforcements loosen and break during
drying, they will damage your dryer.
Preparing laundry for drying
• Check all laundry items before loading
•
•
•
•
them into the product to make sure that
there are no lighters, coins, metal items,
needles and etc. in their pockets or on any
part of them.
Fabric softeners and similar products
must be used in accordance with the
instructions of the manufacturer of the
relevant products.
All laundry must be spun at the highest
spin speed that your washing machine
allows for the laundry type.
Laundry may be tangled after washing.
Separate your laundry before placing them
into your dryer.
Sort your laundry according to their types
and thicknesses. Dry the same type of
laundry together. E.g.: fine kitchen towels
and table cloths dry faster than the thick
bath towels.
Correct load capacity
can be damaged.
CPlace your laundry into the drum loosely so
that they will not get tangled.
CLarge pieces (E.g.: bed sheets, quilt covers,
large tablecloths) may bunch-up. Stop the
dryer 1-2 times during drying process to
separate bunched-up laundry.
Following weights are given as examples.
Home articles
Approximate
weights (g)
Cotton quit covers (double)
1500
Cotton quit covers (single)
1000
Bed sheets (double)
500
Bed sheets (single)
350
Large tablecloths
700
Small tablecloths
250
Tea napkins
100
Bath towels
700
Hand towels
Garments
350
Approximate
weights (g)
Blouses
150
Cotton shirts
300
Shirts
200
Cotton dresses
500
Dresses
350
Jeans
700
Handkerchiefs (10 pieces)
100
T-Shirts
125
Loading
• Open the loading door.
• Place laundry items loosely into the dryer.
• Push the loading door to close. Ensure that
no items are caught in the door.
AConsider the information in the “Programme
Selection Table”. Always start the
programme in accordance with the
maximum load capacity.
CAdding laundry to the machine more
than the level shown in the figure is not
recommended. Drying performance will
degrade when the machine is overloaded.
Furthermore, your dryer and your laundry
9 EN
4 Selecting a Programme and Operating Your Machine
Control panel
1
2
3
4
Mini
Time
Delay
3h
6h
9h
Clean
Filter
Drying
Ready to
Iron
Ready to
Wear
End /
Anticrease
Start/
Pause
Shirts
Ready to
Iron
Freshen Up
Ready to
Wear
20 min.
Ready to
Wear
Ready to
Wear
Plus
10 min.
Extra dry
40 min.
Reset 3’’
Timer
Programmes
7
6
Synthetics
Ready to
Iron
60 min.
Buzzer Cancel
Jeans
Delicates
On / Off
Cottons
5
1. Filter cleaning warning light
5. Programme selection knob
2. Program follow-up indicator
6. Start/Pause/Cancel button
Warning light turns on when the filter is full.
Used to select a programme.
Used to follow-up the progress of the current
programme.
3. Cancel audio warning
Used to start, pause or cancel the programme.
7. Time delay selection button
Used to cancel the audio warning given at the end
of the programme.
Used to set the time delay.
4. On/Off button
Used to turn on and off the machine.
10 EN
Preparing the machine
1. Plug in your machine.
2. Place the laundry in the machine.
3. Press the “On/Off” button.
C Pressing the “On/Off” button does not
necessarily mean that the programme has
started. Press "Start/Pause/Cancel" button
of the machine to start the programme.
Programme selection
Decide the appropriate programme from
the table below which includes drying
temperatures in degrees. Select the desired
programme with the programme selection
button.
Extra dry
Ready to
wear
Ready to
wearPlus
Iron Dry
C
Dry at high temperature only
for cotton laundry. Thick and
multi layered laundry (E.g.:
towels, linens, jeans) are dried
in a way that they do not
require ironing before placing
in the wardrobe.
Normal laundry (E.g.:
tablecloths, underwear) are
dried in a way that they do not
require ironing before placing
in the drawers.
Normal laundry (E.g.:
tablecloths, underwear) are
dried in a way that they do not
require ironing before placing
in the drawers, but more
than those in the ready to
wearoption.
Normal laundry (E.g., Shirts,
dresses) are dried ready to be
ironed.
For further program details, see, “Program
Selection Table”
Main programmes
Depending on the type of laundry, the following
main programmes are available:
•Cottons
You can dry your durable laundry with this
programme. Dries at high temperature. It is
recommended to use for your cotton items
(such as bed sheets, quilt cover, underclothing,
etc.).
•Synthetics
You can dry your less durable laundry with this
programme. It dries at a lower temperature
compared to the cottons programme. It is
recommended for your synthetic laundry (such
as shirts, blouses, synthetic/cotton blended
laundry, etc.).
C Do not dry curtains and lace in your
machine.
•Anti-creasing
A 2-hour anti creasing programme to prevent
laundry from creasing will be activated if
you do not take the laundry out after the
programme is over. This programme rotates
the laundry in 10-minute intervals to prevent
creasing.
Special programmes
For special cases, there are also extra
programmes available:
C Additional programmes may differ
according to the model of your machine.
•Mini
You can use this programme to dry the cottons
that are spun at high speeds in your washing
machine. It can dry your 1,2 kg Cotton laundry
(3 Shirts / 3 T-Shirts) within 30 minutes.
C In order to obtain better results from the
dryer programs, your laundry must be
washed with suitable program and spun
at the recommended spin speeds in your
washing machine.
•Shirt
Dries the shirts in a more sensitive way so that
they are less creased and ironed easily.
C Shirts may contain little amount of
dampness at the and of the program. It is
advised not to leave the shirts in the dryer.
•Jeans
You can use this program to dry the jeans
that are spun at high speeds in your washing
machine.
C Review the relevant part of the program
table.
•Delicates
You can dry at a lower temperature your very
delicate laundry (silk blouses, fine underwear,
etc.) that are suitable for drying or laundry
which is advised to be hand-washed.
C It is recommended to use a cloth bag
to avoid certain delicate garments and
laundry from getting creased or damaged.
Take your garments immediately out of the
dryer and hang them after the programme
ends in order to prevent them being
creased.
•Ventilation
Only ventilation is performed for 10 minutes
without blowing hot air. You can air your
clothes that have been kept at closed
environments for a long time thanks to this
program to deodorize unpleasant odors.
•Timer programs
You can select one of the 10 min., 20 min.,
40 min. and 60 min. timer programmes to
achieve the desired final drying level at low
temperatures. Programme dries at the selected
time regardless of the drying temperature.
11 EN
Program selection and consumption table
2
EN
Programs
Capacity
(kg)
Spin speed in washing
machine (rpm)
Approximate
amount of
remaining
humidity
Drying time
(minutes)
1200-1000
% 60
135
900-800
% 70
150
1200-1000
% 60
75
Cottons / Coloreds
7
A
Ready to Wear
3.5
7
A
Ready to Wear Plus
3.5
7
A
Ready to Iron
3.5
900-800
% 70
90
1200-1000
% 60
140
900-800
% 70
160
1200-1000
% 60
85
900-800
% 70
100
1200-1000
% 60
100
900-800
% 70
115
1200-1000
% 60
60
900-800
% 70
75
Mini
1.2
1200-1000
%50
30
Shirt
1.5
1000-800
%50
49
4
1200-1000
%50
100
800
% 40
55
600
% 50
70
800
% 40
35
600
% 50
45
600
% 50
40
Jeans
Synthetics
3.5
B
Ready to Wear
1.75
Delicates
B
Ready to Wear
1.5
Energy consumption values
Program
Cottons-Ready to Wear Plus*
Capacity
(kg)
Energy consumption value kWh
per year
Energy rating
star
7
305
2.0
* : Energy Label standard program (AS/NZS 2442)
All values given in the table have been fixed according to standard laboratory conditions. These
values may deviate from the table according to the laundry type, laundry spin speed, environmental
conditions and voltage fluctuations.
12 EN
Auxiliary function
Cancel audio warning
Your dryer will give an audio warning when the
programme comes to an end. If you do not
want to hear the audio warning, press “Cancel
Audio Warning” button. The relevant light
will turn on when this button is pressed and
an audio warning will not be given when the
programme comes to an end.
CYou can select this function either before or
after the programme starts.
Warning indicators
CWarning indicators may differ according to
the model of your dryer.
Filter cleaning
A warning light will turn on to remind filter
cleaning after the programme finishes.
CIf the filter cleaning warning light lights up
continuously, please refer to, “Suggested
solutions for problems”.
Time delay
If you wish to dry your clothes at a later time,
thanks to the time delay function, you can
delay the program start up to 3 hours, 6 hours
or 9 hours.
1. Open the loading door and put the laundry
in.
CMake sure that all air outlets are open,
door filter is cleaned and the water tank is
empty.
2. Set the drying program and, if required, the
auxiliary functions.
3. When the time programming button is
pressed once, a 3 hour delay is selected
and the relevant led lights. When the same
button is pressed again, 6 hours; and if
pressed once more, 9 hours delay will be
selected. If the time programming button
is pressed one more time, time delaying
function will be cancelled. Set the time
delay as you require.
4. Delayed operation of the selected program
is started by pressing the "Start/Pause/
Cancel" button after selecting the time
delay.
CAdditional laundry may be loaded / taken
out during the time delay period.
CDuring the time delay period, laundry is
rotated for 4 seconds in every 10 minutes
to prevent creasing.
Canceling the time delay
If you want to cancel the time delay countdown
and start the program:
1. Press “Start/Pause/Cancel” button for
about 3 seconds.
2. Press “Start/Pause/Cancel” button to start
the program right away.
Starting the programme
1. Press “Start/Pause/Cancel” button to start
the programme.
2. Light of the “Start/Pause/Cancel” button
will turn on to indicate that the programme
has started.
Progress of program
Progress of a running program is shown
through the program follow-up indicator.
At the beginning of every program step, the
relevant indicator LED will light up and light of
the completed step will turn off.
“Drying”:
- Drying level will be illuminated during the
whole drying process until the drying degree
reaches “iron dry”.
“Iron Dry”:
- Starts to illuminate when the drying degree
reaches “iron dry” step and remains illuminated
until the next step.
“Ready to wear”:
Starts to illuminate when the drying degree
reaches “Ready to wear” step and remains
illuminated until the next step.
“Final / Anti-creasing”:
- Illuminates when the program comes to an
end and anti-creasing function is activated.
C If more than one LED light up or
flash concurrently, it means there is
malfunctioning or a failure (please see,
Solution suggestions for problems).
Changing the programme after it has
started
You can use this feature to dry your clothes
under higher or lower temperatures after your
dryer has started.
For example;
1. Press and hold the “Start/Pause/Cancel”
button for about 3 seconds to “Cancel”
the programme in order to select “Extra
Dry” programme instead of “Iron Dry”
programme.
2. Select the “Extra Dry” programme by
rotating the programme selection button.
3. Press “Start/Pause/Cancel” button to start
the programme.
CPress “Start/Pause/Cancel” button for 3
seconds to cancel the programme or turn
the programme selection knob in any
direction to end the programme while the
machine is running. Water tank and filter
cleaning warning lights turn on to warn the
user when the programme is cancelled by
pressing the “Start/Pause/Cancel” button
for 3 seconds. However, the warning
lights do not turn on when the programme
is cancelled by turning the programme
selection knob. Only the drying light turns
on and the machine remains in hold until
a new programme is selected and the
“Start/Pause/Cancel” button is pressed.
13 EN
Child-proof lock of the machine should not
be active in order to perform these two
operations. If the child-proof lock is active,
deactivate it before performing these
operations.
Adding/removing laundry in standby mode
In order to add or remove laundry after the
programme starts:
1. Press the “Start/Pause/Cancel” button to
switch the dryer to “Pause” mode. Drying
process will stop.
2. Open the door at “Pause” position and
close it again after adding or taking out
laundry.
3. Press “Start/Pause/Cancel” button to start
the programme.
CAny laundry added after the drying process
has started may cause the dried clothes in
the machine intermingle with wet clothes
and the result will be wet laundry after the
drying process is over.
CLaundry may be added or taken out
as much as desired during a drying
process, but this process will extend the
programme duration and increase energy
consumption since the drying will be
interrupted continuously. Therefore, it is
recommended to add laundry before the
drying programme has started.
Child-proof lock
There is a child-proof lock to prevent any
programme interruption due to the pressing
of button while the programme is running.
The loading door and all buttons except the
“On/Off” button on the control panel are
deactivated when the child-proof lock is active.
Press the “Start/Pause/Cancel” and “Cancel
audio warning” buttons simultaneously for 3
seconds to activate the child-press lock.
To start a new programme after the
programme is over or to interrupt the
programme, the child-proof lock should be
deactivated. Press the same buttons for 3 sec.
again to deactivate the child-proof lock.
CChild-proof lock is deactivated when the
machine is restarted by pressing the On/
Off button.
programme selection knob while the childproof lock is active. Press the buttons for 3
seconds to deactivate the child-proof lock.
Single beep will be heard and child-proof
lock will be deactivated.
A A double beep will be heard if you turn
the programme selection knob when the
machine is running and the child-proof
lock is active. If you deactivate the childproof lock without returning the program
selection knob to its previous position, the
programme will be terminated since the
position of the programme selection knob
is changed. The drying light turns on and
the machine remains on hold until a new
programme is selected and the “Start/
Pause/Cancel” button is pressed.
Finishing by canceling the programme
To cancel any selected programme:
Press “Start/Pause/Cancel” button for about
3 seconds. The “Filter cleaning”, “Water tank”
and “End/ Anti-creasing” warning lights will
turn on at the end of this period for reminding
purposes.
A As the inside of the dryer will be excessively
hot when you cancel the programme while
the dryer is running, activate the ventilation
programme to cool it down.
End of programme
The “End/Anti-creasing”, “Filter cleaning” and
“Water tank” warning lights on the programme
follow up indicator will turn on when the
programme comes to an end. The door can be
opened and the machine becomes ready for a
second cycle.
Press “On/Off” button to turn off the dryer.
CFinal step of the drying cycle (cooling step)
is performed without heat application in
order to keep the items at a temperature
that would not harm them.
CA 2-hour anti creasing programme to
prevent laundry from creasing will be
activated if you do not take the laundry out
after the programme has come to an end.
CIf you will not take the laundry out
immediately, do not stop the dryer before
the drying process is complete.
CClean the filter after each drying (please see,
Filter cleaning).
CDrain the water tank after each drying
(please see, Water tank)
CPress the relevant buttons for 3 seconds
to activate the child-proof lock. A long
beep will be heard and the child-proof lock
will be activated. A double beep will be
heard if you press any button or turn the
14 EN
5 Maintenance and cleaning
Filter Cartridge / Door Inner Surface
Lint and fibres released from the laundry to the
air during the drying cycle are collected in the
“Filter Cartridge”.
C Such fibre and lint are generally formed
during wearing and washing.
C Always clean the filter and the inner
surfaces of the cover after each drying
process.
C You can clean the filter and filter area by
vacuum cleaner.
To clean the filter:
1. Open the loading door.
2. Remove the cover filter by pulling it up and
open the filter.
3. Clean lint, fibre, and cotton raveling by
hand or with a soft piece of cloth. 4.
Close the filter and place it back into its
seat.
C Clogging may arise on the filter surface
after using your machine for some time; if
this occurs, wash the filter with water and
dry it before using again.
C Clean the entire inner surface of the cover
and door gasket.
Sensor (models equipped with a
sensor)
There are humidity sensors in your machine
that detect whether the laundry is dry or not.
For sensor cleaning;
1. Open the door of the machine.
2. Allow the machine to cool off if drying has
been carried out.
3. Wipe the metal sensors with a soft cloth,
dampened with vinegar and dry them.
C Clean metal sensors 4 times a year.
A Never use solvents, cleaning agents or
substances alike when cleaning as these
might cause fire and explosion!
15 EN
6 Solution suggestions for problems
Drying process takes too much time
• The filter mesh may be clogged. Wash with water.
Laundry come out wet at the end of drying.
• The filter mesh may be clogged. Wash with water.
• Excessive laundry might have been loaded in. Do not overload the machine.
Machine does not switch on or the program does not start. Machine is not activated when set.
• It might have not been plugged in. Make sure that the machine is plugged in.
• The loading door may be ajar. Make sure that the loading door is properly closed.
• Program might have not been set or the «Start/Pause/Cancel» button might have not been
pressed. Make sure that the program has been set and it is not in “Pause” mode.
• «Childproof lock» might have been activated. Deactivate the childproof lock.
• The condenser cover on the models with a condenser might not be closed securely. Make
sure that the condenser cover and the red lock is closed securely.
Program has been interrupted without any cause.
• The loading door may be ajar. Make sure that the loading door is properly closed.
• Electricity may be cut off. Press «Start/Pause/Cancel» button to start the program.
• The condenser cover on the models with a condenser might not be closed securely. Make
sure that the condenser cover and the red lock is closed securely.
Laundry has shrunk, become felted or deteriorated.
• A program suitable for the laundry type might have not been used. Dry only the laundry
which is suitable for drying in your machine after checking the labels on your clothes.
• Select a program with suitable low temperature for the laundry type to dry your clothes.
Drum lighting does not come on. (for models equipped with a lamp)
• The machine might have not been started by using the On/Off button. Make sure that the
machine is On.
• Bulb may have blown. Call Beko service to arrange for the bulb to be replaced.
• The condenser cover on the models with a condenser might not be closed securely. Make
sure that the condenser cover and the red lock is closed securely.
2 beeps heard when the buttons are pressed or the program selection knob is turned.
• Childproof lock» might have been activated. Deactivate the childproof lock.
• Program selection knob might be turned to an undefined position. Select one of the
defined programs.
“Filter cleaning” light is flashing.
• Filter might have not been cleaned. Clean the cover filter.
“Final / Anti-creasing” LED is on.
• Program has come to an end. Turn off the machine and take out the laundry.
3 beeps are heard when you press the Start/Pause/Cancel button
• The loading door may be ajar. Make sure that the machine is plugged in.
• Make sure that the condenser cover and the red lock is closed securely.
Also for products equipped with a condenser:
“Water tank” warning LED is flashing.
• Water may be full.
• Drain the water in the water tank.
A Please call Beko Service if the problem persists.
16 EN
Download PDF

advertising