User`s manual | Billion Electric Company 7402VGO Network Router User Manual

BiPAC 7402VGO
VoIP/802.11g ADSL2+ VPN
Firewall Router
Quick Start Guide
VoIP/802.11g ADSL2+ VPN Firewall Router
For more detailed instructions on configuring and using
the Billion VoIP/802.11g ADSL2+ VPN Firewall Router,
please refer to the on-line manual.
Package Contents
VoIP/802.11g ADSL2+ VPN Firewall Router
CD-ROM containing the online manual
RJ-11 ADSL/telephone Cable
Ethernet (CAT-5 LAN) Cable
Console (PS2-RS232) Cable
AC-DC power adapter (12VDC, 1.2A)
This Quick Start Guide
Do not use
temperatures.
this
router
in
high
humidity
or
high
Do not use the same power source for this router as other
equipment.
Warning
Do not open or repair the case yourself. If this router is too
hot, turn off the power immediately and have it repaired at a
qualified service center.
Avoid using this product and all accessories outdoors.
Place this router on a stable surface.
Attention
Only use the power adapter that comes with the package.
Using a different voltage rating power adaptor may damage
this router.
1
Quick Start Guide
The Front LEDs
LED
Meaning
1
PWR
Lit when power is ON.
2
SYS
Lit when the system is ready.
3-5
LAN Port
1X
—
(RJ-45 connector)
7
8–9
Lit green when the wireless connection is established.
Flashes when sending/receiving data.
WLAN
Phone
1X
—
Lit when connected to an Ethernet device.
3X Green for 100Mbps; Orange for 10Mbps.
Blinking when data is Transmitted / Received.
2X
Lit green when the phone is off-hook.
(RJ-11 connector)
2
10
LINE
Lit when the inbound and outbound calls transmitted
through PSTN.
11
VoIP
Lit when SIP registration is OK.
12
PPP / MAIL
Lit steady when there is a PPPoA / PPPoE connection.
Lit and flashed periodically when there is email in the Inbox.
13
ADSL
Lit when successfully connected to an ADSL DSLAM
(“linesync”).
VoIP/802.11g ADSL2+ VPN Firewall Router
The Rear Ports
6
7
8
5
4
9
Port
1
3
2
Meaning
1
Power Switch
Power ON/OFF switch
2
PWR
Connect the supplied power adapter to this jack.
3
RESET
After the device is powered on, press it to reset the
device or restore to factory default settings.
0-3 seconds: reset the device
6 seconds above: restore to factory default settings (this
is used when you can not login to the router, e.g. forgot
the password)
4
LAN
1X
—
(RJ-45 connector)
Connect a UTP Ethernet cable (Cat-5 or Cat-5e) to one
3X of the four LAN ports when connecting to a PC or an
office/home network of 10Mbps or 100Mbps.
5
CONSOLE
Connect a PS2/RS-232 cable to this port when
connecting to a PC’s RS-232 port (9-pin serial port).
6
Phone
1X
─
Connect RJ-11 cable to this port when connecting to an
analog phone set.
2X
(RJ-11 connector)
7
ADSL
8
Antenna
9
LINE
Connect the supplied RJ-11 (“telephone”) cable to this
port when connecting to the ADSL/telephone network.
Connect the detachable antenna to this port.
Connect RJ-11 cable to this port when connecting to the
telephone wall jack.
3
Quick Start Guide
Connecting Your ADSL Router
1. Connect this router to a LAN (Local Area Network) and the ADSL/telephone (ADSL) network.
2. Power on the device.
3. Make sure the PWR and SYS LEDs are lit steadily and that the LAN LED is lit.
4. Connect an RJ11 cable to VoIP port when connecting to an analog phone set.
5. Connect RJ-11 cable to LINE Port when connecting to the telephone wall jack
Switching/
HUB
ADSL
Phone
ADSL
Splitter
Line
Analog Phone
Connect more
computers
4
VoIP/802.11g ADSL2+ VPN Firewall Router
Configuring PC in Windows XP
1. Go to Start / Control Panel (in Classic
View). In the Control Panel, double-click on
Network Connections
2. Double-click Local Area Connection.
3. In the Local Area Connection Status
window, click Properties.
4. Select Internet Protocol (TCP/IP) and click
Properties.
5. Select the Obtain an IP address
automatically and the Obtain DNS server
address automatically radio buttons.
6. Click OK to finish the configuration.
5
Quick Start Guide
Configuring PC in Windows 2000
1. Go to Start / Settings / Control Panel. In the
Control Panel, double-click on Network and
Dial-up Connections.
2. Double-click Local Area Connection.
3. In the Local Area Connection Status
window click Properties.
4. Select Internet Protocol (TCP/IP) and click
Properties.
5. Select the Obtain an IP address
automatically and the Obtain DNS server
address automatically radio buttons.
6. Click OK to finish the configuration.
6
VoIP/802.11g ADSL2+ VPN Firewall Router
Configuring PC in Windows 98/Me
1. Go to Start / Settings / Control Panel. In
the Control Panel, double-click on Network
and choose the Configuration tab.
2. Select TCP/IP ->
NE2000 Compatible, or the name of your
Network Interface Card (NIC) in your PC.
3. Select the Obtain an IP address
automatically radio button.
4. Then select the DNS Configuration tab.
5. Select the Disable DNS radio button and
click OK to finish the configuration.
7
Quick Start Guide
Configuring PC in Windows NT4.0
1. Go to Start / Settings / Control Panel. In the
Control Panel, double-click on Network and
choose the Protocols tab.
2. Select TCP/IP Protocol and click Properties.
3. Select the Obtain an IP address from a
DHCP server radio button and click OK.
8
VoIP/802.11g ADSL2+ VPN Firewall Router
Configuring Your ADSL Router
To configure this device, you must have IE 5.0 /
Netscape 4.5 or above installed
Verifying Your Local Network Connection with the Device
To see if this ADSL Router is
visible on the local network, go
to Start / Run. In the Run dialog
box, type “ping 192.168.1.254”
then press OK.
A command prompt window will
pop out.
If your ping is
successful which means your
local network is able to reach to
the device, then the command
prompt window will close up
automatically.
Connection fails, when you see
“Request timed out” in the
command prompt window. You
may need to check your set up.
9
Quick Start Guide
Connecting to the Router
1.
Open the web browser and type
http://192.168.1.254 in the browser’s
address box. This number is the default IP
address for this router. Press Enter.
2. A username and password window will
appear. The default username and
password are admin and admin. Press
OK to proceed.
3.
You will get a status report web page and main menu screen.
Navigation panel
10
VoIP/802.11g ADSL2+ VPN Firewall Router
At the main menu screen, the left navigation panel where bookmarks are provided links you
directly to the desired setup page, including:
Status (ARP Table, Wireless Association, Routing Table, DHCP Table, PPTP Status,
IPSec Status, L2TP Status, Email Status, VoIP Status, Event Log, Error Log, NAT
Sessions and UPnP Portmap)
Quick Start
Configuration (LAN, WAN, System, Firewall, VPN, VoIP, QoS, Virtual Server, Time
Schedule and Advanced)
Save Config to FLASH
Language (provides user interface in English and French languages).
Please see the relevant sections of on-line manual for detailed instructions
on how to configure your router.
Product Support and Contact Information
Most problems can be solved by referring to the Troubleshooting section in the User’s
Manual. If you cannot resolve the problem with the Troubleshooting chapter, please contact
the dealer where you purchased this product.
Contact Billion
AUSTRALIA
http://www.billion.com.au
©2005 Billion Electric Co Ltd., PC Range P/L. All Rights Reserved.
WORLDWIDE
http://www.billion.com
Mac OS is a registered Trademark of Apple Computer, Inc.
Windows 98, Windows NT, Windows 2000, Windows Me and Windows XP are registered Trademarks of Microsoft
Corporation.
11
Download PDF

advertising