Billy Goat MV650H Lawn Mower User Manual

USER'S GUIDE
10N6-F SERIES 220-240V
2
Thank You
3
Safety Instructions
4
Product View
5
Assembly
6-8
8-13
13-14
Operations
Maintenance and Care
Troubleshooting
14
Replacement Parts
14
Accessories
15
Warranty
16
Consumer Services
Thanks for buying a BISSELL Pet Hair Eraser™ vacuum
We’re glad you purchased a BISSELL vacuum. Everything we know
about floor care went into the design and construction of this
complete, high-tech home cleaning system.
Your BISSELL vacuum is well made, and we back it with a limited
one year warranty. We also stand behind it with a knowledgeable,
dedicated Consumer Services department, so, should you ever have
a problem, you’ll receive fast, considerate assistance.
My great-grandfather invented the floor sweeper in 1876. Today,
BISSELL is a global leader in the design, manufacture, and service
of high quality homecare products like your BISSELL vacuum.
Thanks again, from all of us at BISSELL.
Mark J. Bissell
Chairman & CEO
2
w w w. b i s s e l l . c o m IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance,
basic precautions should be observed,
including the following:
■Remove plug from electrical outlet before
Read all
instructions
before using your
Upright VACUUM.
replaced by the manufacturer or its service
agent in order to avoid a hazard.
■Do not pick up toxic material (chlorine
bleach, ammonia, drain cleaner, petrol, etc.).
■Do not allow to be used as a toy.
■Do not use for any purpose other than
described in this User’s Guide.
■Use only manufacturer’s recommended
attachments.
■Do not use with any opening blocked; keep
free of dust, lint, hair, and anything that
may reduce air flow.
■Keep appliance on a level surface.
■Turn off all controls before unplugging.
■Be extra careful when cleaning stairs.
■This appliance is provided with double insulation. Use only identical replacement parts.
■Do not use without the dirt container and
filters in place.
■Pay close attention when working around
children.
■Unplug before attaching Pet TurboBrush™
Tool.
■Do not pick up hard or sharp objects such as
glass, nails, screws, coins, etc.
WARNING:
To
reduce the risk of fire,
electric shock, or injury:
■Do not use outdoors or on wet surfaces.
■Do not leave machine when it is plugged in.
■Do not use with damaged cord or plug.
■If appliance is not working as it should, has
been dropped, damaged, left outdoors, or
dropped into water, return it to a service agent.
■Do not pull or carry by cord, use cord as a
handle, close door on cord, pull cord around
sharp corners or edges, run appliance over
cord, or expose cord to heated surfaces.
■Do not unplug by pulling on cord. unplug
by grasping plug.
■Do not handle plug or appliance with
wet hands.
■Do not expose hair, loose clothing, fingers
or body parts to openings or moving parts.
■Do not pick up hot or burning objects such
as cigarettes, matches, or hot ashes.
■Do not pick up flammable or combustible
materials (lighter fluid, petrol, kerosene,
etc.) or use in the presence of explosive
liquids or vapour.
■Do not use appliance in an enclosed space
filled with vapours given off by oil base
paint, paint thinner, some moth proofing
substances, flammable dust, or other
explosive or toxic vapours.
■Not intended for use by persons (including
children) with reduced physical, sensory or
mental capabilities, or lack of experience
and knowledge, unless they have been
given supervision or instruction concerning
use of the appliance by a person
responsible for their safety
■Young children should be supervised to ensure
that they do not play with the appliance.
w w w. b i s s e l l . c o m cleaning or maintaining the appliance.
■If the supply cord is damaged, it must be
SAVE THESE
INSTRUCTIONS
FOR FUTURE USE
This model is for household use only.
IMPORTANT
FOR OPERATION ON A 220-240 VOLT
A.C. 50/60 Hz POWER SUPPLY ONLY.
If your appliance is fitted with a
nonrewireable BS 1363 plug it must not be
used unless a 13 amp (ASTA approved to BS
1362) fuse is fitted in the carrier contained
in the plug. (Spares may be obtained from
your BISSELL supplier). If for any reason the
plug is cut off, it must be disposed of, as it is
an electric shock hazard should it be inserted
into a mains socket.
3
Product view
Handle
Quick Release™
Cord Wrap
Hose Clip
Stretch Hose
Dusting Brush/
Upholstery Tool
Carry
Handle
Pet TurboBrush™
Tool
Crevice Tool
Twist ‘n Snap™
Hose
Inner Cyclone
Power
Cord
Hose
Wand
Power Switch
Upper Tank
Extension
Wand
Easy
Empty™ Dirt
Container
Post-Motor
HEPA Media
Filter*
Washable
Pre-Motor
Filter
Headlight
Lock ‘n Seal™ Lever
Quick
Release™
Cord
Wrap
Handle
Release Pedal
Foot
Window
Height Adjustment
Knob
Wide Cleaning Foot
* T he filter media, not the vacuum as a
whole, complies with the IEST-RP-CC001.5
HEPA Standard.
4
w w w. b i s s e l l . c o m Hose Wand Base
CAUTION:
Do not plug in your vacuum
until you are familiar with all
instructions and operating
procedures.
Assembly
The only tool you’ll need to
assemble your vacuum cleaner
is a Phillips screwdriver.
4.
2.
Attach handle to vacuum
1. Locate the handle and cord wrap. Remove
the screw packet taped to the handle.
2. Stand the vacuum upright and from the
rear of the unit, slide the base of the
handle firmly into the grooves at the top
of the vacuum body.
3. Ensure that the handle fits firmly to the vacuum
body. If there are any gaps, continue to push
firmly until the handle is secure.
3.
1.
4. Insert the provided screw into the existing
hole, attaching the handle to the body of the
vacuum. Tighten securely with a screwdriver.
Attach vacuum hose and tools
1. Attach the Twist ‘n Snap™ Hose by lining up
the tabs on the base with the corresponding
notches on the back of the vacuum as shown.
Twist 'n
Snap Hose
6
2. Turn the Twist ‘n Snap Hose to the right
to lock the hose into place.
3. Grasping the Quick Reach Handle, slide the
end of the Hose Wand onto the Hose Wand
Base. Snap the Hose into the Hose Clip.
NOTE: The vacuum will not operate
effectively unless the hose wand is
firmly attached.
4. Slide the extension wand and crevice tool
into the storage clip on back of vacuum.
5. Slide the dusting brush/upholstery tool
into the storage clip on back of vacuum.
6. Store the Pet TurboBrush™ Tool on the front
of the handle by lining up the TurboBrush
base with the base of the holder then push
back to snap into place.
* T he filter media, not the vacuum as a
whole, complies with the IEST-RP-CC001.5
HEPA Standard.
w w w. b i s s e l l . c o m CAUTION:
Before using your vacuum, make
sure that the dirt container is in
the locked position and that all
filters (pre-motor and Post-Motor
HEPA Media Filter*) are in place.
Do not operate your vacuum
without these filters.
NOTICE:
For above floor cleaning, the floor brush
will continue to rotate, but is raised
above floor. To prevent carpet damage,
do not lean on the vacuum or let the
powerfoot tilt forward.
5
Operations
Power switch
caution:
The Power Switch is located on the left
side of the vacuum. Push the rocker
switch “ON” (I) to vacuum, and “OFF”
(O) when cleaning is complete.
To avoid personal injury
and to prevent the cleaner
from falling when cleaning
stairs, always place it at
the bottom of the stairs.
Handle positions
Press the handle release pedal, located
on the lower left side of the vacuum, with
your foot to place your vacuum into one
of three cleaning positions.
1. Upright – For storage and above floor
cleaning with tools.
2. Normal Cleaning – Press handle
release pedal once. Position used for
most household floor cleaning tasks.
3. Low Cleaning – With the vacuum in
normal cleaning position, press handle
release pedal again. Use for reaching
under low furniture such as tables,
chairs or beds.
Height adjustment
The powerfoot/rotating floor brush on
your vacuum can be adjusted to clean
several floor surfaces.
NOTE: For optimal cleaning
performance, adjust to the lowest
practical setting. If your cleaner is
difficult to push, adjust to the next
higher setting.
1. Turn height adjustment knob to desired setting.
Bare Floor
For non-carpeted,
indoor surfaces
Lowest Setting For short pile carpets
Medium Setting For short and medium
pile carpets
Highest Setting For plush pile carpet
Transporting cleaner
1. To move your cleaner from room to room,
put the handle in the upright position, tilt
the cleaner back on its rear wheels and
push forward.
2. The cleaner can also be moved by using
the carry handle.
6
w w w. b i s s e l l . c o m 1.
2.
3.
Tip:
Before cleaning under low furniture,
check area first for objects that might
harm the unit or block the vacuum hose.
1.
Height Adjustment Knob
1.
Correct way to
carry
Operations
Special on-board tools
Your vacuum is not only a powerful
carpet and rug cleaner, it’s also a
versatile above floor vacuum cleaner
when you select one of the special tools.
1. Raise the handle to the upright position.
Dusting Brush/
Upholstery Tool
Crevice Tool
2. Grasp the hose wand handle to separate Extension Wand
from hose wand base.
Hose Wand
3. Attach tools by firmly pushing onto vacuum hose, hose wand or extension wand.
Be sure the hose and tool fit snuggly
together by twisting tightly.
Dusting Brush/Upholstery Tool:
Two types of cleaning tools in one attachment.
•Use brush side to dust furniture,
blinds, books, lamps, shelves and
baseboards.
•Use upholstery side for cushions,
draperies and fabrics.
Hose Wand
Base
Crevice Tool: Use in tight narrow spaces.
Extension Wand: Use with desired
attachment for a longer reach.
Tip:
Hose Wand: Use with desired attachment
for a longer reach or for cleaning hard to
reach places.
Pet TurboBrush™ Tool: Use rotating
brush action for small flat areas such
as cushions and beds.
NOTE: Press gently down and pull
towards you in a raking motion.
Too much pressure will cause the
brush to stop rotating.
w w w. b i s s e l l . c o m Pet TurboBrush™
Tool
Before cleaning
under low furniture,
check area first for
objects that might
harm the unit or
block the vacuum
hose.
caution:
The rotating floor brush continues
to rotate while tools are in use.
To reduce the risk of injury from
moving parts, always move the
cleaner with the carrying handle.
Always place vacuum cleaner on
the floor with handle in upright
position when using tools. Never
place your fingers under the cleaner
when it is running. Never place
powerfoot on furniture or uneven
surfaces. Do not place vacuum
cleaner close enough to objects to
pull them into rotating brush.
7
Operations
Power cord usage
1. To use your vacuum, remove the cord and
plug it into an electrical outlet. For your
convenience, there is a quick release cord
wrap for easy cord removal. There is also
a cord clip that is part of the upper cord
wrap where you can attach the cord
when vacuuming.
1.
Quick Release
Cord Wrap
2. When you are finished cleaning, turn
vacuum cleaner off.
3. Unplug power cord by grasping the plug
(NOT the cord) and disconnect from outlet.
4. Loop power cord around cord wraps on
side of vacuum cleaner. Be sure to first
return the quick release cord wrap back
to its original position before wrapping
the cord.
5. Clip molded plug to power cord to secure.
Maintenance and care
To maximize your cleaning
performance and extend the life of
your vacuum, it is very important that
you empty your dirt container and
check and clean your filters frequently.
Perform the following maintenance
steps:
1. Empty the dirt container when the dirt
reaches the “Full” line on the container, or
more frequently to prevent overfills. For best
performance, empty after each use.
2. Check the pre-motor filter and post-motor
HEPA Media Filter* at least once a month,
clean or replace as needed.
3. Replace the post-motor HEPA Media
Filter* every three to six months.
NOTE: More frequent filter cleaning
may be necessary if you are
vacuuming new carpet, fine dust,
or have allergy concerns. Follow
the instructions on the following
pages to perform these simple
maintenance steps.
* T he filter media, not the vacuum as a
whole, complies with the IEST-RP-CC001.5
HEPA Standard.
8
w w w. b i s s e l l . c o m WARNING:
To reduce the risk of electric
shock, turn power switch OFF and
disconnect plug from electrical outlet before performing maintenance
or troubleshooting checks.
Tip:
To maximize cleaning performance,
check and clean or replace all filters
as suggested.
Maintenance and care
Emptying the dirt container
The dirt container should to be
emptied before the dirt reaches
the “Full” line on the container.
1. Unplug the vacuum from electrical
outlet.
2.
2. Slide the Lock ‘n Seal Lever to the
“Unlock” position.
3. Grasp handle and pull the dirt container
straight out to remove from the vacuum.
Unlock
4.
4. Empty dirt into garbage container.
NOTE: Emptying the dirt container
after every use will help prevent
over filling and ensure that the
vacuum is ready to go the next
time you clean.
Cleaning the Pre-motor and Post-motor HEPA Media Filter*
1. Unplug the vacuum from electrical outlet.
2. The pre-motor filter protects the motor from
dirt particles. It is located in the slide out
tray underneath the dirt container. If the
filter becomes dirty, pull out the tray, lift
out the foam filter pad and clean it.
NOTE: The pre-motor filter may be Washable
Pre-Motor
hand washed in cold water with
mild detergent. Rinse well and air Filter
dry thoroughly before replacing.
3. The post-motor HEPA media filter* assists
in the filtration process to return clean air
to the room. It is located behind the door
on the side of the vacuum. If the filter
becomes dirty, remove the door, remove
the filter and replace.
NOTE: The post-motor filter is
a white, pleated HEPA Media
Filter*. This filter is not washable
and must be replaced when it
becomes dirty.
Post-Motor
HEPA
Media
Filter*
NOTICE:
This product is intended for household
use only and not for commercial or
industrial use. Vacuuming of dust
from products like plaster, concrete
or ashes will damage the motor and
void the warranty.
WARNING:
* T he filter media, not the vacuum as a
whole, complies with the IEST-RP-CC001.5
HEPA Standard.
w w w. b i s s e l l . c o m Do not operate cleaner with
damp or wet filters or without
all filters in place.
9
Maintenance and care
Check rotating floor brush and drive belt
You should check your vacuum cleaner’s
rotating floor brush and drive belt regularly for wear or damage. You should also
clean the brush and brush ends of strings,
hair and carpet fibers. This type of debris
can wrap around the brush and hamper
its ability to effectively clean your carpet.
Also remove any debris that has
accumulated under the brush cover.
1. Unplug the vacuum from electrical outlet.
WARNING:
To reduce the risk of injury
from moving parts, turn
vacuum cleaner off and
disconnect power plug from
electrical outlet.
2. Place handle in low position and turn vacuum
cleaner over so bottom side is facing up.
3. Remove the two screws marked 2 and
4. Once the screws are removed, lift tab
1 and release the three latches in order
marked 2 - 4. Lift off the brush cover
3.
1
4. Grasp rotating floor brush at both ends and lift.
5. Clean strings, hair and other debris from
rotating floor brush, paying particular
attention to brush ends.
2
3
4
6. Clean strings, hair and other debris from
motor pulley and drive belt areas.
7. Check drive belt carefully for wear, cuts
or stressed areas.
8. Check air passageway for obstructions.
Remove debris from this area.
8.
Motor
Pulley
9. Insert front edge of the brush cover and
rotate into place. Snap the latches and
replace the two screws.
Replace drive belt
1. Unplug the vacuum from electrical outlet.
2. With rotating floor brush removed from
vacuum cleaner (Steps 1-4 of check
rotating floor brush and drive belt),
grasp old drive belt and remove from
motor pulley. Discard the old drive belt.
10
w w w. b i s s e l l . c o m Air Passageway
Maintenance and care
Replace drive belt continued
3. Place new drive belt over motor pulley
and loop other end over rotating floor
brush in the space between the bristles.
NOTE: It is important that you use
only genuine BISSELL replacement
belts. Generic belts may not meet
the exact specifications required
to keep your vacuum operating
at its peak performance. The use
of unbranded belts could lead to
early failure of the vacuum and
could void your warranty.
3.
Motor
Pulley
4. Pull the rotating floor brush firmly into
position, stretching the drive belt, and
place ends of rotating floor brush
down into the slots on sides as shown.
Alignment of brush ends in slots may be
necessary to fully insert the brush.
5. Turn rotating floor brush by hand several
times in the direction of motor pulley. If
properly installed, drive belt will center
itself on rotating brush crown.
6. Insert front edge of brush cover and
rotate into place. Snap the three latches
and replace the two screws.
2.
Replacing lightbulb
1. Unplug the vacuum from electrical outlet.
2. Using a screwdriver, first remove 2
screws on either side of lens and pull
out to remove the lens.
3.
3. Remove the bulb from the socket by grasping
the bulb and pulling gently. Install the new
bulb by pushing it gently into the socket until 4.
the bulb snaps into place.
4. Reposition the lens place cover back
over headlight and reinsert 2 screws.
Maintaining Pet TurboBrush™ Tool
The Pet TurboBrush™ Tool should be
checked regularly for clogs or debris
wrapping around the brush.
1. Remove tool from hose or front of vacuum.
2.
2. Twist collar so opening is at the top and
lift top cover to remove.
w w w. b i s s e l l . c o m 11
Maintenance and care
Maintaining Pet TurboBrush™ Tool continued
4.
3. Remove the brush from the belt and
clean debris.
4. Replace the brush inside the belt and
place ends into slots on sides as shown.
5. Reposition top cover making sure to line
up inside tab at the front with the opening on the cover. Twist collar until opening is at the bottom to lock into place.
5.
Clearing clogs
Low suction or poor pickup may be
due to a clog in the vacuum cleaner.
If you notice a change in the sound of
the motor, check for clogs.
1. Unplug the vacuum from electrical outlet.
2. Empty dirt container.
3. Check upper tank for build up or clogs.
5.
4. If you notice a clog in the upper tank,
remove the inner cyclone (see section
"Cleaning the upper tank" below).
2.
5. Grasp the hose wand and separate it
from the hose wand base. Check for a
clog in the base, the wand or in the hose.
6. Remove the Twist ‘n Snap hose from the
vacuum by turning to the left. Straighten
the hose and unclog with a long, narrow
object such as a broom handle.
7. If the clog persists, follow the instructions
for "Checking the rotating floor brush and
drive belt" on page 10 and inspect the air
passageway for obstructions.
1.
Cleaning the upper tank
1. Grasp the inner cyclone and twist to the
left until the locking tabs stop the rotation.
Pull down from the upper tank to remove it.
2. Wipe out the inside of the upper tank and
the inner cyclone with a damp cloth moistened with water or a mild cleaning solution.
3. If you desire to thoroughly clean the
filtration disk located in the upper
portion of the inner cyclone, hold the
bottom of the cyclone and turn filtration
disk to the right and pull up to remove.
12
w w w. b i s s e l l . c o m 3.
Maintenance and care
Cleaning the upper tank continued
4. The inner cyclone and filtration disk may
be washed using a mild detergent. Be
sure it is completely dry before reassembling or damage to your unit may result.
5.
6.
5. Once cleaning is completed, reassemble
the filtration disk over the inner cyclone
by sliding it straight down on the top of
the inner cyclone and turning left. Be sure
to line up the tabs when reassembling for
proper installation.
6. To replace the inner cyclone, slide it into
the upper housing. Be sure to line up the
inner cyclone by ensuring tabs on filtration
disk are positioned toward the front of
the unit. Push the inner cyclone in and
rotate it to the right until the locking tabs
stop the rotation.
Troubleshooting
WARNING:
To reduce the risk of electric
shock, turn power OFF and
disconnect plug from electrical
outlet before performing
maintenance or
troubleshooting.
Vacuum cleaner won’t run
Possible causes
Remedies
1. Vacuum cleaner is not plugged in
1. Check electrical plug
2. Damaged power cord
2. Replace as necessary by an authorized service representative.
Vacuum cleaner and tools won’t pick up dirt
Possible causes
Remedies
1. Incorrect height adjustment
1. Adjust powerfoot to correct height
2. Hose not attached to suction opening
2. Firmly push hose wand into hose wand base
3. Twist 'n Snap hose not securely attached
3. Make sure Twist 'n Snap hose is snapped into locked position
4. Crack or hole in hose
4. Check hose and replace if needed
5. Broken or worn drive belt
5. Replace drive belt, see pages 10-11
6. Rotating floor brush bristles worn
6. Replace brush
7. Rotating floor brush jammed
7. Remove brush and clean debris from brush ends
8. Clog in vacuum
8. Clear clogs, see page 12.
9. Dirt container full 9. Empty dirt container
10. Dirt container not installed properly
10. Position correctly and lock in place
11. Filters are dirty
11. Check pre-motor and post-motor filters
12. Pet TurboBrush™ Tool is clogged or 12. See pages 11-12 for Maintaining
debris is wrapped around the brush roll Pet TurboBrush™ Tool
Vacuum cleaner is difficult to push
Possible causes
1. Incorrect height setting
w w w. b i s s e l l . c o m Remedies
1. Adjust powerfoot to correct height setting
13
Troubleshooting
Visible dirt escaping from cleaner
Possible causes
Remedies
1. Dirt container full
1. Empty dirt container
2. Filters missing or installed incorrectly
2. Check pre-motor and post-motor filters for correct installation
3. Dirt container installed incorrectly
3. Pull out and re-insert dirt container correctly
Other maintenance or service not included in the manual should be
performed by an authorized service representative.
Thank you for selecting a BISSELL product.
Please do not return this product to the store.
Replacement parts
Item
1
2
3
4
5
1
Part No.
Part Name
303-1120
203-1603
203-1283
203-1073
203-6608
2
Style 7/9/10/12/14 Drive Belt (2-Pack)
Headlight Bulb
Wide Window Foot Brush Roll (gray)
Style 7/8/14 Pre-Motor Foam Filter
Style 8/14 Post-Motor HEPA Media Filter*
3
4
5
Accessories
Item
1
2
3
4
5
1
Part No.
Part Name
203-1056
203-1059
203-1429 203-1068
203-1216
2
Crevice Tool
Dusting Brush/Upholstery Tool
Pet TurboBrush™ Tool
Extension Wand
Twist 'n Snap Vacuum Hose (clear)
3
4
5
* T he filter media, not the vacuum as a
whole, complies with the IEST-RP-CC001.5
HEPA Standard.
14
w w w. b i s s e l l . c o m Warranty - BISSELL Pet Hair Eraser™ Vacuum
This warranty gives you specific legal rights, and you may also have other rights which may vary from country to
country. If you need additional instruction regarding this warranty or have questions regarding what it may cover,
please contact BISSELL Consumer Services by E-mail, telephone, regular mail as described below, or contact your
local in country distributor.
Limited One Year Warranty
Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, BISSELL will repair or replace (with new or
remanufactured components or products), at BISSELL’s option, free of charge from the date of purchase by the
original purchaser, for one year any defective or malfunctioning part due to manufacturer defect.
This warranty applies to product used for personal, and not commercial or rental service. This warranty does not
apply to fans or routine maintenance components such as filters. Damage or malfunction caused by negligence,
abuse, neglect, unauthorized repair, or any other use not in accordance with the User's Guide is not covered.
BISSELL recommends that the original packaging be kept for the duration of the warranty period in case such need
arises within the warranty period that the item need re-packing and transportation.
BISSELL Consumer Services:
If your BISSELL product should require service or if you need information about repairs, authorized
service centers in your area, replacement parts or your warranty, please contact BISSELL Consumer
Services, as indicated below, or contact your local in-country distributor.
For Australian inquiries:
Monday – Friday 9 am - 5 pm
BISSELL AUSTRALIA PTY LIMITED
42 Rocco Dr.
Scoresby 3179
Victoria
Australia
Telephone: 1.800.811.183
For New Zealand inquiries:
Monday – Friday 9 am - 5 pm
Parex Industries Ltd.
5 Tolich Place
Henderson 0610
Auckland
New Zealand
Telephone: 0800.247.735
For all other inquiries:
Monday – Friday 8 am - 4 pm
BISSELL Homecare, Inc.
PO Box 1888
Grand Rapids, Michigan 49501 USA
Telephone: 01.616.453.4451
Fax: 01.616.453.1383
*EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY
BISSELL and its in-country distributors are NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE
ASSOCIATED WITH THE USE OF THIS PRODUCT. BISSELL’S LIABILITY WILL NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT.
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER ORAL OR WRITTEN. ANY IMPLIED WARRANTIES WHICH
MAY ARISE BY OPERATION OF LAW, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, ARE LIMITED TO THE one YEAR DURATION FROM THE DATE OF PURCHASE AS described above.
FOR AUSTRALIAN CONSUMERS ONLY: Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any
other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the
goods fail to be of acceptable quality and the failure does not amount to a major failure.
THIS WARRANTY IS IN ADDITION TO OTHER RIGHTS OR REMEDIES UNDER LAW. NOTHING IN THIS WARRANTY EXCLUDES, LIMITS
OR MODIFIES ANY LIABILITY OF BISSELL WHICH IS IMPOSED BY LAW, OR LIMITS OR MODIFIES ANY REMEDY AVAILABLE TO THE
CONSUMER WHICH IS GRANTED BY LAW. TO MAKE A CLAIM UNDER THIS WARRANTY CONTACT BISSELL AUSTRALIA PTY LTD (DETAILS
ABOVE). CONTACT BISSELL PRIOR TO RETURNING ANY GOODS. WHERE AGREED, BISSELL WILL REIMBUSE REASONABLE POSTAGE /
HANDLING COSTS (IF ANY) FOR RETURNING GOODS TO BISSELL.
w w w. b i s s e l l . c o m 15
BISSELL consumer services
If your BISSELL product should require service:
Call BISSELL Consumer Services at the numbers below and we will give you the location of a
BISSELL Authorized Service Center in your area. If you have questions about your warranty or
need replacement parts please contact the numbers below. Or visit the BISSELL
website - www.bissell.com
For Australian inquiries:
Monday - Friday 9 am — 5 pm
BISSELL Australia PTY LTD
42 Rocco Drive
Scoresby 3179
Victoria
Australia
Telephone: 1 800 811 183
For New Zealand inquiries:
Monday - Friday 9 am — 5 pm
Parex Industries LTD.
5 Tolich Place
Henderson 0610
Auckland
New Zealand
Telephone: 0.800.247.735
For all other inquiries:
Monday - Friday 8 am — 4 pm
BISSELL Homecare, Inc.
PO Box 1888
Grand Rapids, Michigan 49501 USA
Telephone: 01-616-453-4451
Fax: 01-616-453-1383
When contacting BISSELL, have model number of cleaner
available.
Please record your Model Number: ___________________
Please record your Purchase Date: ___________________
NOTE: Please keep your original sales receipt. It
provides proof of purchase date in the event of a
warranty claim. See Warranty on page 15 for details.
16
©2012 BISSELL Homecare, Inc
Grand Rapids, Michigan
All rights reserved. Printed in China
Part Number 110-4512
Rev 1/12
Visit our website at:
www.bissell.com
w w w. b i s s e l l . c o m