Billy Goat OS551H Lawn Mower User Manual

PR & OS Owner’s Manual
Patent 6253416
BILLY GOAT POWER RAKE AND OVERSEEDER
PR550, PR550H, PR550T, PR500HT, OS551, OS551H, PR600S, OS600S
Owner's Manual
Accessories
Replacement Parts
SLICING REEL
SLICING BLADES
OVERSEEDER KIT
FLAIL BLADES
A complete vertislicing reel for your
PR. 20" wide reel for
use in grasses that
require vertical
cutting, and for
assisting in lawn
overseeding projects.
A full set of blades for
replacement. Includes
new lockwashers for
replacement
installation.
The new light weight Plastic Overseeding
Kit is constructed of durable High Density
Polypropylene with two lift handles on
each side to assist in lifting the entire unit
and easily converts a PR Series Power
Rake into an overseeder with 4 bolts and
minimal tools.
NOTE: Overseeder Conversion Kit
(350328) includes Slicing Reel (350343).
Part No. (350325) comes with the
Overseeder Box only.
A complete set of
our high quality flail
blades for your PR.
Includes new lock
clips for
replacement
installation.
P/N 350345
P/N 350347
P/N 350325 / 350328
P/N 350186
Part No 350324
1
FLAIL SHAFTS
A full set of shafts
for replacement.
Includes new lock
clips for
replacement
installation.
P/N 350185
Form No F021108D
PR & OS Owner’s Manual
ABOUT THIS MANUAL
THANK YOU for purchasing a BILLY GOAT ® Power Rake/Overseeder. Your new machine has been carefully
designed and manufactured to provide years of reliable and productive service. This manual provides complete
operating and maintenance instructions that will help to maintain your machine in top running order. Read this
manual carefully before assembling, operating, or servicing your equipment.
CONTENTS
SERIAL PLATE DATA AND SPECIFICATIONS
GENERAL SAFETY
3
4-5
SOUND AND VIBRATION
6
INSTRUCTION LABELS
7
PACKING CHECKLIST & ASSEMBLY
8
OPERATION
9-12
MAINTENANCE
13
TROUBLESHOOTING AND WARRANTY PROCEDURE
14
ILLUSTRATED PARTS LIST
15-18
PARTS LIST
19
MAINTENANCE RECORD
20
Part No 350324
2
Form No F021108D
PR & OS Owner’s Manual
SERIAL PLATE DATA
Record the model number, serial number, date of
purchase, and where purchased.
Purchase Date:
Purchased From:
Specifications
PR550
PR550H
OS551
OS551H
PR550T
PR550HT
PR600S
OS600S
Engine: HP
5.5 (4.1 kW)
5.5 (4.1 kW)
5.5 (4.1 kW)
5.5 (4.1 kW)
5.5 (4.1 kW)
5.5 (4.1 kW)
6.0 HP (4.7kW)
6.0 HP (4.7kW)
Engine: Model
1104020191
GX160T1QX2
1104020191
GX160T1QX2
1104020191
GX160T1QX2
EX17D50012
EX17D50012
Engine: Type
B&S OHV
HONDA OHV
B&S OHV
HONDA OHV
B&S OHV
HONDA OHV
SUBARU
SUBARU
Engine: Fuel Capacity
3.0 qt. (2.84 L)
3.88 qt. (3.6 L)
3.0 qt. (2.84 L)
3.88 qt. (3.6 L)
3.0 qt. (2.84 L)
3.88 qt. (3.6 L)
3.8 qt.(3.6 L)
3.8 qt.(3.6 L)
Engine: Oil Capacity
0.66 qt. (0.62 L)
0.69 qt. (0.65 L)
0.66 qt. (0.62 L)
0.69 qt. (0.65 L)
0.66 qt. (0.62 L)
0.69 qt. (0.65 L)
0.63 qt.(0.60 L)
0.63 qt.(0.60 L)
Total Unit Weight:
149# (67.7 kg)
147# (66.8 kg)
162# (73.6 kg)
160# (72.7 kg)
139# (63.2 kg)
137# (62.3 kg)
137# (62.3 kg)
137# (62.3 kg)
Engine weight:
36# (16.3 kg)
34# (15.4 kg)
36# (16.3 kg)
34# (15.4 kg)
36# (16.3 kg)
34# (15.4 kg)
34# (15.4 kg)
34# (15.4 kg)
15o
20o
15o
15o
20o
20o
20o
20o
Sound test in accordance with
2000/14/EC
101 dB(a)
101 dB(a)
101 dB(a)
101 dB(a)
101 dB(a)
101 dB(a)
101 dB(a)
101 dB(a)
Sound at operators ear
82 dB(a)
82 dB(a)
82 dB(a)
82 dB(a)
82 dB(a)
82 dB(a)
82 dB(a)
82 dB(a)
0.82g (8.04
2
m/s )
0.82g (8.04
m/s2)
3.2g
3.2g
3.2g
3.2g
3.2g
3.2g
Max. operating slope
Vibration at operator position
Part No 350324
3
Form No F021108D
PR & OS Owner’s Manual
GENERAL SAFETY INSTRUCTIONS and SYMBOLS
The safety symbols shown below are used throughout this manual. You should become familiar with them before
assembling, operating, or servicing this equipment.
This symbol indicates important information that will prevent injury to yourself or others.
This symbol indicates ear protection is recommended when operating this equipment.
This symbol indicates eye protection is recommended when operating this equipment.
This symbol indicates gloves should be worn when servicing this equipment.
This symbol indicates that this manual and the engine manufacturer’s manual should be read
carefully before assembling, operation, or servicing this equipment.
This symbol indicates important information that will prevent damage to your BILLY GOAT
Power Rake/Overseeder.
®
This symbol indicates the engine oil level should be checked before operating this
equipment.
Read and make sure you thoroughly understand the following safety precautions before assembling, operating or
servicing this equipment:
READ this manual and the engine manufacturer’s manual carefully before assembling,
operating, or servicing this equipment.
EAR PROTECTION is recommended when operating this equipment.
EYE PROTECTION is recommended when operating this equipment.
BREATHING PROTECTION is recommended when operating this equipment.
EXHAUST from this product contains chemicals known to the State of California to cause
cancer, birth defects or other reproductive harm.
DO NOT operate this equipment on any unimproved forested, brushy, or grass covered land
unless a spark arrester is installed on the muffler as required by Section 4442 of the
California Public Resources Code. The arrester must be maintained in good working order.
Other states may have similar laws. Federal laws apply on federal lands.
DO NOT run engine in an enclosed area. Exhaust gases contain carbon monoxide, an
odorless and possibly fatal poison.
Part No 350324
4
Form No F021108D
PR & OS Owner’s Manual
DO NOT run this equipment indoors or in any poorly ventilated area. Refueling outdoors is
recommended.
DO NOT refuel this equipment while the engine is running. Allow engine to cool for at least
two minutes before refueling.
DO NOT store gasoline near an open flame.
DO NOT remove gas cap while engine is running.
DO NOT start or operate engine if strong odor of gasoline is present.
DO NOT start or operate engine if gasoline is spilled. Move equipment away from spill until
gasoline has completely evaporated.
DO NOT smoke while filling the fuel tank.
DO NOT check for spark with spark plug or spark plug wire removed. Use an approved spark
tester.
DO NOT operate engine without a muffler. Inspect muffler periodically and replace if
necessary. If equipped with muffler deflector, inspect deflector periodically and replace if
necessary.
DO NOT operate engine with grass, leaves or other combustible material near the muffler.
DO NOT touch muffler, cylinder, or cooling fins when hot. Contact with hot surfaces may
cause severe burns.
DO NOT leave equipment unattended while in operation.
DO NOT park equipment on a steep grade or slope.
DO NOT operate equipment with bystanders in or near the work area.
DO NOT allow children to operate this equipment.
DO NOT operate equipment with guards removed.
DO NOT operate equipment near hot or burning debris or any toxic or explosive materials.
DO NOT operate equipment on slopes greater than specified in Specifications section of this
manual.
DO NOT start engine without height adjust lever in up position and clutch bail disengaged.
DO NOT place hands or feet underneath unit, or near any moving parts.
ALWAYS remove spark plug wire when servicing equipment to prevent accidental starting.
ALWAYS check fuel lines and fittings frequently for cracks or leaks. Replace if necessary.
ALWAYS keep hands and feet away from moving or rotating parts.
ALWAYS store fuel in approved safety containers.
WARNING: Important
Remove all rocks, wire, string, etc. that can present a hazard during work prior to starting.
DO identify and mark all fixed objects to be avoided during work such as sprinkler heads,
water valves, buried cables, or clothes line anchors, etc.
Part No 350324
5
Form No F021108D
PR & OS Owner’s Manual
SOUND
SOUND LEVEL 82 dB(a) at Operators Position
Sound tests were conducted in accordance with 2000/14/EC, and were performed on 2-13-2002 under the
conditions listed below.
Sound power level listed is the highest value for any model covered in this manual. Please refer to serial plate on
the unit for the sound power level for your model.
General Conditions:
Temperature:
Wind Speed:
Wind Direction:
Humidity:
Barometric Pressure:
Sunny
48oF (8.9oC)
2 mph (3.2 kmh)
South East
29%
30.34Hg (770 mm Hg)
VIBRATION DATA
VIBRATION LEVEL .82g (8.04m/s2)
Vibration levels at the operator’s handles were measured in the vertical, lateral and longitudinal directions using
calibrated vibration test equipment. Tests were performed on 5-25-2006 under the conditions listed below.
General Conditions:
Temperature:
Wind Speed:
Wind Direction:
Humidity:
Barometric Pressure:
Sunny
72.32oF (22.4oC)
3.8 mph (6.12kph)
East
62.2%
29.9Hg (101.3kpa)
INTENDED USE
INTENDED USE: This machine is designed for removing thatch from your lawn, renovation of existing lawns, and to
assist in overseeding operations. The machine should not be used for any other purpose than that stated above.
Do not operate if excessive vibration occurs. If excessive vibration occurs, shut engine off immediately and check
for damaged or worn reel, loose pulley bolts or set screws, loose engine or lodged foreign objects. (See trouble
shooting section on page 14).
Part No 350324
6
Form No F021108D
PR & OS Owner’s Manual
INSTRUCTION LABELS
®
The labels shown below were installed on your BILLY GOAT Power Rake/Overseeder. If any labels are damaged or missing, replace them
before operating this equipment. Item numbers from the Illustrated Parts List and part numbers are provided for convenience in ordering
replacement labels. The correct position for each label may be determined by referring to the Figure and Item numbers shown.
LABEL DANGER KEEP HANDS
AND FEET AWAY
ITEM #51 P/N 400424
LABEL CAUTION GUARDS
ITEM #52 P/N 900327
LABEL CLUTCH ITEM #49
P/N 830503
LABEL EXPLOSIVE FUEL
ITEM # 50 P/N 400268
DANGER FLYING DEBRIS
ITEM # 48 P/N 810736
LABEL INSTRUCTION HEIGHT ADJ.
ITEM #35 P/N 350176
LABEL INSTRUCTIONS SEEDER BOX
ITEM #45 P/N 350288
ENGINE LABELS
BRIGGS & STRATTON
HONDA
OIL ALERT
WHEN OIL LEVELLOW,
ENGINE STOPS IMMEDIATELY.
ENGINE CONTROLS
Honda
Briggs & Stratton
Set lever to choke when starting cold
Throttle lever
Fuel valve
Part No 350324
Set lever to desired engine speed.
Move lever completely to the left to
stop engine
Choke lever
7
Form No F021108D
PR & OS Owner’s Manual
PACKING CHECKLIST
Your Billy Goat Power Rake is shipped from the factory in one carton, completely assembled.
READ all safety instructions before assembling unit.
TAKE CAUTION when removing the unit from the box the Handle Assembly is attached to the
unit by cables.
PUT OIL IN ENGINE BEFORE STARTING
PARTS BAG &
LITERATURE ASSY
Warranty card P/N- 400972, Owner’s Manual P/N-350324, Declaration of Conformity P/N-350139.
26
28
28
Boxing Parts
Checklist
Briggs & Stratton
5.5 Intek OHV
Honda 5.5 OHV
28
Subaru 6HP EX17
Literature Assy
P/N-430334
PR550, PR550H,
PR550T, PR550HT,
PR600S
OS551, OS551H,
and OS600S
ASSEMBLY
1. UNFOLD the upper handle (item 26) and slide handle lock loops (item 28) into place to secure the upper handle
to the lower.
2. CHECK engine oil level and fill to proper level with engine manufacturers recommended grade of oil. Move
height adjust lever to down position, to level engine during checking. See engine manufacturers instruction
manual.
3. CONNECT spark plug wire.
Part No 350324
8
Form No F021108D
PR & OS Owner’s Manual
OPERATION
Like all mechanical tools, reasonable care must be used when operating machine.
Inspect machine work area and machine before operating. Make sure that all operators of this
equipment are trained in general machine use and safety.
PUT OIL IN ENGINE BEFORE STARTING
STARTING
ENGINE: See engine manufacturer’s instructions for type and amount of oil and gasoline used. Engine must be
level when checking and filling oil and gasoline.
FUEL VALVE: Move fuel valve to "ON" position (when provided on engine).
STOP SWITCH: Located on the engine. "ON" position.
CHOKE: Operated with choke lever on side of engine.
THROTTLE: Controlled by throttle lever on the motor.
IF YOUR UNIT FAILS TO START:
See Troubleshooting on page 14.
FOLDING HANDLE
This unit is equipped with a folding upper handle for easier storage and transportation. The handle can be folded by
sliding the handle lock loops (item 28) up. This releases the upper handle, allowing it to be folded over the unit.
HANDLING & TRANSPORTING:
This unit requires two people to lift it. With the handle in the folded position, lift holding the lower handle and
belt/shaft guard one on each side of the machine. Secure the machine in place during transport. See page 3 for
weight specifications
Never lift the machine while the engine is running.
counter clockwise
to raise blades
ADJUSTING BLADE DEPTH
The depth of the blades can be raised or lowered by rotating the knob on the
top of the adjustment lever. The blades are lowered by rotating the knob
clockwise, and raised by rotating the knob counter-clockwise. The relative
depth of the blades can be gauged by using the depth scale located on the
right front corner of the engine base. With new blades installed the depth can
be estimated as follows: 2.5 on the scale is even with the ground, 3 is equal
to 0.25" deep, and 3.5 is equal to 0.5" deep
clockwise to
lower blades
blades up
transport
blades up
transport
BLADE POSITION & DEPTH CONTROL LEVER
The blades can be raised or lowered into the ground by height adjustment lever
on the engine base. The height adjuster lock lever must be pushed back against
the adjustment lever in order to lower the blades into the ground. The resulting
blade depth can be adjusted higher or lower.
See ADJUSTING BLADE DEPTH.
blades dow n
running
SPRING TINE CONVERSION
If are converting your Power rake to a spring tine reel, you will need
to replace the spacer on the control lever to accommodate for the
tine. First remove the clip (item 18), then unscrew the yoke (item
17), remove the washer (items 69) and insert the spacer (item 75) in
front of the spring. Reassemble in reverse order.
Part No 350324
9
Form No F021108D
PR & OS Owner’s Manual
RAKING/SLICING TIPS
Before beginning, it is best to evaluate the condition of the lawn by cutting one or more core
samples from area to be treated. A core can be cut using a piece of pvc, or metal pipe.
Hammer the pipe into the ground, remove it, push the core out of the pipe and inspect it to
determine the depth of thatch in your yard.
THATCH: Thatch is a dense layer of dead grass, clippings, and roots that builds up over time
at the base of of the lawn preventing air, water, and fertilizer from reaching the soil. This can
cause shallow root development and make a lawn more susceptible to drought and disease.
Thatch also provides an ideal environment for insects to hide and multiply. Periodic removal of
thatch will keep your lawn in good health.
HEAVY THATCH: Lawns with an excessive amount of thatch will require multiple treatments
for effective removal. Trying to remove excessive thatch (greater than 3/4"[19 mm] deep) in
one treatment will damage or destroy the living part of the lawn. It is best to remove heavy
thatch in seasonal treatments (i.e. spring, and fall).
SLOPES: Rake slopes across not up and down. This is much easier and safer for the
operator and is better for the lawn. Raking across will help to reduce runoff during watering
and allow the sloped ground to hold more seed, fertilizer, and water. The units maximum
operating slope is 35% or 19°.
DEPTH: The wide range of depth adjustment on your unit is provided to allow for blade wear.
Setting the reel deeper will not produce better, or quicker results. The flail reel is intended to
be set so it just touches the surface on flat ground. The slicing reel should be set even with the
ground for verti-slicing work, and set to a maximum 1/2" depth for overseeding jobs. Setting
the reel deeper than this will only result in premature wear on the unit (i.e. failed belt). If you
desire to work the ground deeper than the above guidelines allow, it should be done gradually
in multiple passes..
SLICING / OVERSEEDING: Mow the lawn to shorter than the normal cut height before
starting (i.e. approximately 2" tall for fescue grass). For the best result, Slice/Overseed in crisscross pattern (See Fig. 1 and See Fig 2).
Fig. 1
Fig. 2
RAKING OPERATION-FLAIL REEL
NOTE: Must have the flail reel assembly (350112) for this operation.
MOW: Mow the lawn to it's normal cut height.
DRY: Be sure grass is dry. Wet conditions can cause increased damage to healthy grass.
SET DEPTH: With engine off, set the raking depth so that the blades just touch on a flat
surface (i.e. driveway, or sidewalk).
START ENGINE: See page 9 for further instruction.
ENGAGE BLADES: Pull back on the bail on the operators handle. NOTE: When engaging the
blades in heavy load conditions (i.e. heavy thatch, or very uneven turf), push down on the
operators handle lifting the front wheels slightly. Engage the blades. Slowly lower the unit into
the turf.
RAKE: Rake a small test area and examine the results. Thatch should be removed and
deposited on top of the healthy grass. If excessive damage occurs to healthy grass, adjust the
blade depth to decrease damage. Continue raking the yard, working in one direction (i.e.
north-south, or east-west). NOTE: If a large drop in engine RPM occurs, or the unit pulls you
forward and bounces during operation the blade depth is set too low.
REMOVE THATCH: After raking, a layer of thatch will be deposited over the top of the lawn.
This thatch must be removed prior to any fertilizing, seeding, or watering of the lawn. We
suggest the use of a lawn vacuum or wheeled blower for collection and removal of the thatch.
Part No 350324
10
Form No F021108D
PR & OS Owner’s Manual
RAKING OPERATION-SPRING REEL
NOTE: Must have the spring tine reel assembly (350354) for this operation.
MOW: Mow the lawn to it’s normal cut height. Tall grass will not leave a manicured look when the
dethatching job is complete.
DRY: Be sure grass is relatively dry. Wet conditions can cause increased damage to healthy grass.
SET DEPTH: With engine off, set the raking depth so that the spring tines are just above touching the
flat surface (i.e. driveway, or sidewalk) the units height is being adjusted on. NOTE: Allowing the
spring tines to have substantial contact with the ground will cause premature wear and failure of the
spring tines.
START ENGINE: See page 9 for further instruction.
ENGAGE TINES: Pull back on the bail on the operators handle. NOTE: When engaging the spring
tines in heavy load conditions (i.e. heavy thatch, or very uneven turf), push down on the operators
handle lifting the front wheels slightly. Engage the spring tines. Slowly lower the unit into the turf.
RAKE: Rake a small test area and examine the results. Thatch should be removed and deposited on
top of the healthy grass. If excessive damage occurs to healthy grass, adjust the spring tine depth to
decrease damage. Continue raking the yard, working in one direction (i.e. north-south, or east-west).
NOTE: If a large drop in engine RPM occurs, or the unit pulls you forward and bounces during
operation the spring tine depth is set too low.
REMOVE THATCH: After raking, a layer of thatch will be deposited over the top of the lawn. This
thatch must be removed prior to any fertilizing, seeding, or watering of the lawn. We suggest the use
of a lawn vacuum or wheeled blower for collection and removal of the thatch.
VERTI-CUTTING OPERATION
NOTE: Must have the slicing reel assembly (350113) for this operation.
MOW: Mow the lawn to shorter than the normal cut height (approximately 2" tall)
DRY: Be sure grass is dry. Wet conditions can cause increased damage to healthy grass.
SET DEPTH: With engine off, set the raking depth so that the blades just touch on a flat surface
(i.e. driveway, or sidewalk).
START ENGINE: See Page 9.
ENGAGE BLADES: Pull back on the bail on the operators handle. NOTE: When engaging the
blades in heavy load conditions (i.e. heavy thatch, or very uneven turf), push down on the
operators handle lifting the front wheels slightly. Engage the blades. Slowly lower the unit into the
turf.
SLICE: Verti-cut a small test area and examine the results. Some thatch and cut stems should
be removed and deposited on top of the healthy grass. Grass runners should be cut and ready
for removal. If excessive damage occurs to healthy grass, adjust the blade depth to decrease
damage. Continue raking the yard, working in one direction (i.e. north-south, or east-west).
NOTE: If a large drop in engine RPM occurs, or the unit pulls you forward and bounces during
operation the blade depth is set too low.
REMOVE THATCH/STEMS: After verti-cutting, a layer of thatch and cut stems will be deposited
over the top of the lawn. We suggest the use of a lawn vacuum or wheeled blower for collection
and removal of the thatch/stems.
OVERSEEDING OPERATION
NOTE: Must have the slicing reel assembly (350113) for this operation.
MOW: Mow the lawn to shorter than the normal cut height (approximately 2" tall)
DRY: Be sure grass is dry. Wet conditions can cause increased damage to healthy grass.
SEED: Spread grass seed according to the seed suppliers directions (e.g. 10 lbs. per 1000 ft2 [4.5
kg. per 93 m2 ])
SET DEPTH: With engine off, set the raking depth so that the blades reach 1/4"-1/2"(6-12 mm)
below a flat surface (i.e. driveway, or sidewalk).
START ENGINE: See Page 9.
ENGAGE CLUTCH: Pull back on the bail on the operators handle. NOTE: When engaging the
clutch in heavy load conditions (i.e. heavy thatch, or very uneven turf), push down on the operators
handle lifting the front wheels slightly. Engage the clutch. Slowly lower the unit into the turf.
SLICE: Run machine over the area that has been seeded to incorporate the seed into the soil. If
excessive damage occurs to healthy grass, adjust the blade depth to decrease damage. Continue
raking the yard, working in one direction (i.e. north-south, or east-west). NOTE: If a large drop in
engine RPM occurs, or the unit pulls you forward and bounces during operation the blade depth is
set too low.
WATER/FERTILIZE: After the seed has been worked into the soil, water and fertilize according to
the seed suppliers directions.
Part No 350324
11
Form No F021108D
PR & OS Owner’s Manual
ADJUSTING SEED RATE
STOP
SETTING
DROPPING SEEDS
- PULL BACK ON THE KNOB THEN
SLIDE THE BRACKET TO DESIRED
STOP SETTING.
EXAMPLE: STOP SETTING IS ON 4
- IF SLICING WITHOUT DROPPING
SEEDS FOR LONG PERIOD THEN
SET THE STOP SETTING TO ZERO.
BRACKET
KNOB
LAWN PREPARATION
- MOW LAWN TO LOWEST SETTING ON
YOUR MOWER.
- DO NOT WATER PRIOR TO SEEDING.
- POWER RAKE TO DETHATCH LAWN
AND REMOVE THATCH.
- FERTILIZE LAWN WITH BROADCAST
SPREADER.
- AFTER ADJUSTING THE STOP SETTING, LIFT
UP ON THE BAR TO OPEN THE DROP SEEDER
DOOR.
LAWN PREPARATION
- FOR BEST RESULTS OVERSEED IN
TWO PASSES OF ONE-HALF
APPLICATION RATE EACH, AT RIGHT
ANGLES OR IN A CRISS-CROSS
PATTERN.
- WATER HEAVILY IMMEDIATELY THEN
LIGHTLY FOR 10 - 14 DAYS, KEEPING
SOIL MOIST.
- AFTER GERMINATION, WATER LESS
OFTEN TO PROMOTE ROOT GROWTH.
- TO STOP DROPPING SEEDS, PUSH FORWARD
ON THE HANDLE TO CLOSE THE DROP SEEDER
DOOR.
NOTE: IF SLICING WITHOUT DROPPING SEEDS
FOR LONG PERIOD OF TIME THEN SET THE
STOP SETTING TO ZERO.
S E E D A P P L IC A T IO N C H A R T :
T H E S E S E T T IN G S A R E A P P R O X IM A T E G U ID E L IN E S . S E E D IN G R A T E S A R E S P E E D D E P E N D E N T .
F A S T E R T R A V E L D E L IV E R S L E S S S E E D .
SEED
TYPE
RATE
STOP
LBS
S E T T IN G
RATE
SEED
TYPE
1 ,0 0 0 F T 2
RYEGRASS
BLUEGRASS
FESCUE
Part No 350324
1 ,0 0 0 F T
1 /2
1
3 /4
2
1 1 /2
3
2 1 /3
4
3 /4
STOP
LBS
S E T T IN G
2
2 /3
1
1 1 /3
2
BERMUDAGRASS
3 /4
1
( H U L L E D & Z O Y S IA )
1 2 /3
2
1
BENTGRASS
REFERENCE
CHART
B IL L Y
GOAT
SEEDER
S E T T IN G
SCOTTS
SEEDER
S E T T IN G
5
6 1 /3
3
1
4
C E N T IP E D E G R A S S
2 /3
1 1 /2
5
(C O A T E D )
1 1 /4
2
2 1 /2
6
2 1 /2
3
3 /4
5
S T . A U G U S T IN E
3 /4
3
1 1 /4
6
GRASS
1
4
2
7
1 1 /3
5
3 1 /2
8
1 1 /2
6
12
(A L L D R O P
SEEDER
M ODELS)
6
8
7
10
8
1 5 1 /2
9
17
Form No F021108D
PR & OS Owner’s Manual
MAINTENANCE
PERIODIC MAINTENANCE
Periodic maintenance should be performed at the following intervals:
Maintenance Operation
Every Use (daily)
Every 25 Hours
z
Inspect for loose, worn or damaged parts.
z
Check engine oil
z
Inspect belt
Engine (See Engine Manual)
z
Grease reel bearings
z
Inspect and clean engine air filter
z
Oil height adjustment linkage
FLAIL BLADE WEAR
1. Wait for engine to cool and disconnect spark plug.
2. Close fuel valve on engine (if available).
3. Lean unit back onto lower handles and secure in place.
4. Inspect blades for wear, and immediately replace any bent or cracked blades. Measure the
overall length of the blade. (See fig. 1)
5. If blades measure less than 3.25"(83 mm) in overall length they must be replaced. NOTE: We
recommend replacing all the flails at once.
SLICING BLADE WEAR
1. Wait for engine to cool and disconnect spark plug.
2. Close fuel valve on engine (if available).
3. Lean unit back onto lower handles and secure in place.
4. Inspect blades for wear, and immediately replace any bent or cracked blades. Measure
the overall length of the blade from the center of the attachment bolt to the tip of the worn
blade.
5. If blades measure less than 3"(76 mm) in length they must be replaced. NOTE: We
recommend replacing all the blades at once.
Fig. 1
ROTATING FLAIL REEL END TO END
To maximize flail blade life and performance the reel can be rotated end to end periodically to provide a fresh lead cutting edge. Takes approx. 20 min.
and requires 1/2" and 9/16" socket wrenches with extension bar.
1. Wait for engine to cool and disconnect spark plug.
2. Close fuel valve on engine (if available).
3. Lean unit back onto lower handles and secure in place.
4. Remove (7) lock nuts (item 62 & 40) holding the belt and shaft guards (item 21 & 22) in place. It is necessary to lower the height adjust lever to reach
the locknuts on the guards. Remove the guards.
5. Remove the drive belt (item 9) by "walking" it out of the groove on the reel pulley (item 2).
6. Remove the (4) lock nuts (item 60) and washers (item 68) holding the bearings (item 23) to the frame of the unit.
7. The reel is now free from the machine. Slide the reel down and out of the machine.
8. Remove the capscrew (item 71), lockwasher (item 57), reel pulley (item 2), key (item 42), and reel spacer (item 10) from the end of the reel.
9. Rotate the reel end to end, and re-install these items on the opposite end of the reel.
10. Re-install the reel in reverse order of removal. Re-install the guards in reverse order of removal.
DRIVE BELT REPLACEMENT
NOTE: Takes approx. 10 min. and requires 1/2" socket wrench with extension.
1. Wait for engine to cool and disconnect spark plug.
2. Remove (4) lock nuts (item 62) holding the belt guard (item 21) in place. It is necessary to lower the height adjust lever to reach the locknuts on the
guard. Remove the guard.
3. Remove the belt (item 9) by rotating the reel pulley (item 2) and walking it out of the groove. Discard old belt
4. Install new belt using same procedure to walk the belt into the groove.
5. With new belt installed pull bail rod back to engaged position and measure extension of idler spring. Spring should stretch 3/4" - 1" (19 25 mm) with
bail engaged. Adjust clutch cable as necessary to achieve this extension.
6. Re-install the belt guard.
Part No 350324
13
Form No F021108D
PR & OS Owner’s Manual
STORAGE
Never store engine indoors or in enclosed poorly ventilated areas with fuel in tank, where fuel fumes may reach an open
flame, spark or pilot light, as on a furnace, water heater, clothes dryer or other gas appliance.
If engine is to be unused for 30 days or more, prepare as follows:
Remove all gasoline from carburetor and fuel tank to prevent gum deposits from forming on these parts and causing possible
malfunction of engine. Drain fuel outdoors, into an approved container, away from open flame. Be sure engine is cool. Do not
smoke. Run engine until fuel tank is empty and engine runs out of gasoline.
Troubleshooting
P ro b le m
A b n o rm a l v ib ra tio n .
P o s s ib le C a u s e
· D a m a g e d o r m is s in g b la d e s . L o o s e
h a n d le b o lts . L o o s e e n g in e b o lts
E n g in e s ta lls o r la b o rs w h e n
ra k in g
· B la d e s s e t to o d e e p in to g ro u n d .
E n g in e w ill n o t s ta rt.
· S to p s w itc h o ff (H o n d a o n ly). T h ro ttle · C h e c k c h o k e p o s itio n .
in o ff p o s itio n
· O u t o f g a s o lin e o r b a d , o ld g a s o lin e . · C h e c k g a s o lin e .
· S p a rk P lu g w ire d is c o n n e c te d .
· G a s v a lv e o ff.
· D irty a ir c le a n e r.
E n g in e is lo c k e d , w ill n o t p u ll
o v e r.
· D e b ris lo c k e d a g a in s t re e l, o r d riv e
p u lle ys . E n g in e p ro b le m .
S o lu tio n
· S to p w o rk im m e d ia te ly. R e p la c e a n y
d a m a g e d o r m is s in g b la d e s . T ig h te n a ll
lo o s e n u ts a n d b o lts .
· R a is e b la d e s s o th a t th e y ju s t to u c h th e
g ro u n d o n a le v e l s u rfa c e
· C o n n e c t s p a rk p lu g w ire .
· T u rn o n g a s v a lv e .
· C le a n o r re p la c e a ir c le a n e r. C o n ta c t a
q u a lifie d s e rv ic e p e rs o n .
· P u ll s p a rk p lu g w ire a n d re m o v e d e b ris .
C o n ta c t a n e n g in e s e rv ic in g d e a le r fo r
e n g in e p ro b le m s .
When servicing engine refer to specific manufacturers engine owner's manual. Engine warranty is covered by the
specific engine manufacturer. If your engine requires warranty or other repair work contact your local servicing
engine dealer. When contacting a dealer for service it is a good idea to have your engine model number available
for reference (See table page 3). If you cannot locate a servicing dealer in your area you can contact the
manufacturers national service organization.
To reach:
American Honda: 800-426-7701
WARRANTY CLAIM PROCEDURE
Should a BILLY GOAT ® machine fail due to a defect in material and/or workmanship, the owner should make a
warranty claim as follows:
• The machine must be taken to the dealer from whom it was purchased or to an authorized Servicing BILLY
GOAT Dealer.
•
The owner must present the remaining half of the Warranty Registration Card, or, if this is not available, the
invoice or receipt.
•
The Warranty Claim will be completed by the authorized BILLY GOAT Dealer and submitted to their
respective BILLY GOAT Distributor for their territory Attention: Service Manager. Any parts replaced under
warranty must be tagged and retained for 90 days. The model number and serial number of the unit must
be stated in the Warranty Claim.
•
The distributor service manager will sign off on the claim and submit it to BILLY GOAT for consideration.
•
The Technical Service Department at BILLY GOAT will study the claim and may request parts to be
returned for examination. BILLY GOAT will notify their conclusions to the distributor service manager from
whom the claim was received.
•
The decision by the Technical Service Department at BILLY GOAT to approve or reject a Warranty Claim is
final and binding.
For online product registration go to www.billygoat.com
Part No 350324
14
Form No F021108D
PR & OS Owner’s Manual
POWER RAKE SEEDER BOX KIT
P/N 350325
PARTS LIST
ITEM NO.
1
2
3
4
5
6
7
9
10
11
12
13
14
15
16
17
18
19
21
22
24
25
26
28
29
30
32
33
34
PART NO.
350366
350306
350276
350320
350271
350272
350273
350370
8171003
900321
400217
8024040
8024021
8123087
8160001
350332
8160002
350369
350280
350372
8197031
9195106
8172007
8154007
8059136
350288
890456
350313
DESCRIPTION
BOX AND LID ASSEMBLY
BRACKET ADJ DROP SEEDER ASSY
BAR DOOR LINKAGE
SHAFT PLASTIC DROP SEEDER
PLATE DOOR DROP SEEDER
PLATE DOOR DROP SEEDER END
PLATE DOOR DROP SEEDER ARM
PULLEY 3V GROOVE 0.625" BORE
WASHER 5/16 FLAT CUT
BEARING CLIP 1.375 OD
SPRING TENSION
BOLT CARRIAGE 5/16 - 18 X 1
BOLT CARRIAGE 1/4-20 X 3/4"
SCREW SELF TAP #10-24 X 3/8" HMS ZP
NUT LOCK 1/4
BRACKET SLOT PLASTIC SEEDER BOX
NUT LOCK 5/16
PULLEY 3V GROOVE 1.530" BORE
WASHER 0.906 O.D. X 0.656 I.D. X 0.062
BELT O-RING 5/16 X 15 9/16"
PIN COTTER 1/8" X 1"
ROLL PIN 1/8 - 1 1/4
WASHER 1/4 SAE
NUT HEX 10-24
SCREWCAP #10-24 X 3/4
LABEL INSTRUCTION SEEDER BOX
LABEL HOSE PLUG KD/SV
LABEL PRODUCT DECAL OS
QTY
1
1
1
1
1
1
1
1
1
4
2
1
1
4
1
1
1
1
2
1
1
1
1
2
2
1
1
1
PARTS BAG SEEDER BOX KIT 350326
19
20
23
27
31
32
Part No 350324
8160002
8177011
8041026
8172020
8171006
8161044
350327
NUT LOCK 5/16 (REQUIRE ON THE OLD MODELS ONLY)
WASHER LOCK 5/16
SCREWCAP 5/16-18 x 3/4
WASHER 5/16 FENDER
WASHER 1/2 FC
NUT LOCK 1/2" THIN HGT
LIT SEEDER BOX (INCLUDES TEMPLATE)
15
4
4
4
4
3
1
1
Form No F021108D
PR & OS Owner’s Manual
FLAIL REEL KIT 350112
PARTS DRAWING
item
no.
57
71
73
74
76
77
78
79
PARTS
LIST
LOCK W ASHER TW ISTED TOOTH
SCREW CAP REEL PULLEY
SHAFT FLAIL BLADE
BLADE FLAIL
SPACER BUMPER 5/8" x 1/2"
SHAFT W A FLAIL REEL
CLIP LOCK 1/2"
W ASHER 1/2 SAE
FLAIL SHAFT KIT 350185
PARTS
item
no.
LIST
73 SHAFT FLAIL BLADE
78 CLIP LOCK 1/2"
PARTS
item
no.
LIST
74 BLADE FLAIL
78 CLIP LOCK 1/2"
4
8
SPACER BUMPER KIT 350258
PARTS
item
no.
LIST
76 SPACER BUMPER 5/8" x 1/2"
Part No 350324
1
1
4
30
54
1
8
8
FLAIL BLADE KIT 350186
Part No. QTY
350141
350146
QTY
Part No.
400502
8041050
350141
350100
350144
350145
350146
8172011
350100
350146
60
8
SLICING BLADE KIT 350187
QTY
Part No.
350144
Part No. QTY
PARTS LIST
item
no.
81 BLADE 10" HEX SLICING
85 SCREWCAP 1/4-20 X 3/4 HCS ZP
86 NUT LOCK 1/4-20
54
16
QTY
Part No.
350147
8041004
8142004
Form No F021108D
20
40
40
PR & OS Owner’s Manual
SLICING REEL ASSY 350113
PARTS DRAWING
item
no.
PARTS
PR500
LIST
Part No.
QTY
57
LOCK WASHER 5/16 TWISTED TOOTH
800177
1
71
SCREWCAP 5/16 - 24 x 1" HCS GR. 5
400164
1
80
SHAFT SLICING WA
350142
1
81
BLADE SLICING REEL
350147
20
82
PLATE BLADE MTG.
350148
20
83
SPACER BLADE MTG.
350149
10
84
SPACER BLADE ASSY
350150
9
85
SCREWCAP 1/4-20 x 3/4, HCS ZP
8041004
40
86
NUT LOCK 1/4-20
8142004
40
87
COLLAR SPACER
350152
1
88
WASHER 0.937 x 1.750 x 0.119
350153
1
89
WASHER LOCK 7/8 INT. TOOTH
350154
1
90
NUT JAM 7/8-14
350155
1
SPRING TINE REEL ASSY - 350355-S
item
no.
1
2
3
4
5
6
PARTS
LIST
SHAFT WA SPRING TINE REEL
SHAFT SPRING TINE REEL
SPRING TINE
RING RETAINING 1/2"
SCREWCAP 5/16"-24x1" GR. 5 ZP
WASHER LOCK TWISTED TOOTH HEAVY
Part No.
QTY
350353
350351
350352
350146
400164
430298
1
4
108
8
1
1
SPRING REPLACEMENT KIT - 350356-S
PARTS
item
no.
LIST
3
SPRING TINE
4
RING RETAINING 1/2"
Part No 350324
17
QTY
Part No.
350352
350146
108
8
Form No F021108D
PR & OS Owner’s Manual
PARTS DRAWING
PR550, PR550H, PR550T,
PR550HT, PR600S, OS551,
OS551H, OS600S
Part No 350324
18
Form No F021108D
PR & OS Owner’s Manual
PARTS LIST
item
no.
1
1A
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
65A
65B
66
67
68
69
70
71
72
73
74
75
76
77
78
PARTS
LIST
Pulley 3" OD
Spacer Crank PR Honda
Pulley 6.5" OD X ¾"
Wheel 8" Front PR
Wheel 10" Front PR
Height Adjust Assy
Reel Flail / Slicing / Spring Assy
Pulley Idler 2.75"
Arm Idler WA
Belt 5L X 36
Spacer Reel Pulley
Bracket Mount Clutch Cable
Chassis WA W/ Label
Frame Front WA
Bushing 0.375 OD X 0.256 ID X 0.88
Spring Height Adjust PR500
Link Height Adjust PR500
Yoke ½ - 20
Pin Yoke ½"
Bracket Mount Hgt. Adj. WA
Spacer Spanner Wheel PR500
Guard Belt WA W/ Label
Guard Shaft WA W/ Label
Bearing ¾" Cast Pillow Block
Handle Lower LH WA
Handle Lower RH WA
Handle Upper PR500
Bail Clutch WA
Loop Folding Handle
Deflector Rubber
Shield Bearing
Bar Clamp Deflector
Bracket Height Adjust Lock WA
Guard Pulley Back
Lever Height Control
Label Instr. Hgt. Adj.
Bolt Shoulder ¼" x 1 ¾"
Bolt Shoulder 5/16" x 1 ¾"
Cable Clutch Reel PR500
Spring Extension
BOLT SHOULDER 1/2" X 1"
ENGINE HONDA 5.5 H.P. GX160
ENGINE INTEK 5.5HP OHV B&S
ENGINE SUBARU 6HP EX17
KEY 3/16" X 1"
GRIP 1" x 13"
GRIP LEVER 1/8 x 1 x 5"
LABEL INSTRUCTION SEEDER BOX
WASHER 5/16 FC
FINGER BELT WIRE
LABEL DANGER THROWN OBJECT
LABEL CLUTCH VQ
LABEL HOT ENGINE
LABEL WARNING
LABEL DANGER GUARD
PLUG CAP 1" RD
BOLT CARRAIGE 3/8-16 x 1 3/4
BOLT CARRAIGE 5/16-18 x 1 3/4
BOLT CARRIAGE 5/16 -18 x 3/4
LOCK WASHER TW. TOOTH
NUT LOCK #10-24
NUT LOCK 1/4-20
NUT LOCK 3/8-16
NUT LOCK 3/8-16 THIN
NUT LOCK 5/16-18
SCREWCAP 1/4-20 x 1 1/2
SCREWCAP 3/8 - 16 x 1 1/2
SCREWCAP 5/16-24 x 3/4" GR.5
Washer 3/4 SAE
Washer 5/16 Twist Tooth
SCREWCAP 5/16 - 18 x 1 1/2
SCREWCAP 5/16-24 X 1
WASHER 3/8 FLAT CUT
WASHER 1/2 FC
NUT LOCK 1/2" - 13 THIN HGT
SCREWCAP REEL PULLEY
BUTTON SOCKET 5/16-18X5/8”
BOLT SHOULDER 1/2" x 2"
NUT FLANGE 5/16-18
S P A C E R 1 /2 " ID X 3 /4 "
W A S H E R 3 /8 S A E
N U T P A L 3 /8
W A S H E R 1 /4 F L A T C U T
Part No 350324
PR550
QTY
PR550H
QTY
OS551
QTY
OS551H
QTY
Part No.
350101-01
350102
350103
350104
350107
350112
350114
350115
350116
350118
350119
350194
350121
350309
350125
350126
350127
350128
350182
350130
350195
350196
350133
350134
350135
350375
350374
350138
350167
350168
350171
350173
350184
350175
350176
350178
350179
350181
400217
500114
350197
9201078
400570
500181
8171003
350301
810736
830503
400268
400424
900327
890132
8024061
8024043
8024039
400502
8164005
8160001
8160003
8161042
8160002
8041008
8041052
8042026
8041030
400164
8171004
8171006
8161044
8041050
350266
520031
350346
1
1
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
1
1
2
1
1
1
1
2
1
2
1
1
1
1
1
1
1
1
1
1
1
1
2
1
2
1
1
1
1
2
1
2
4
2
4
1
1
2
9
3
18
1
1
3
4
1
8
2
4
1
4
2
4
Part No.
350101
350339
350102
350103
350104
350107
350112
350114
350115
350116
350118
350119
350194
350121
350309
350125
350126
350127
350128
350182
350130
350195
350196
350133
350134
350135
350375
350374
350138
350167
350168
350171
350173
350174
350175
350176
350178
350179
350181
400217
500114
600115
9201078
400570
500181
8171003
350301
810736
830503
400268
400424
900327
890132
8024061
8024043
8024039
400502
8164005
8160001
8160003
8161042
8160002
8041008
8041052
8042026
8172015
430298
8041030
400164
8171004
8171006
8161044
8041050
350266
520031
350346
1
1
1
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
1
1
2
1
1
1
1
2
1
2
1
1
1
1
1
1
1
1
1
1
1
2
2
1
2
1
1
1
1
2
1
2
4
2
4
1
1
2
9
3
18
1
1
4
1
1
4
1
8
2
4
1
4
2
4
Part No.
350101-01
350102
350103
350104
350107
350113
350114
350115
350116
350118
350119
350194
350121
350309
350125
350126
350127
350128
350182
350130
350195
350196
350133
350134
350135
350375
350374
350138
350167
350168
350171
350173
350184
350175
350176
350178
350179
350181
400217
500114
350197
9201078
400570
500181
350288
8171003
350301
810736
830503
400268
400424
900327
890132
8024061
8024043
8024039
800177
8164005
8160001
8160003
8161042
8160002
8041008
8041052
8042026
8041030
400164
8171004
8171006
8161044
400164
350266
520031
350346
1
1
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
1
1
2
1
1
1
1
2
1
2
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
8
1
1
1
1
2
1
2
4
2
5
1
1
5
9
3
19
1
1
3
4
1
8
5
4
1
4
2
4
Part No.
350101
350339
350102
350103
350104
350107
350113
350114
350115
350116
350118
350119
350194
350121
350309
350125
350126
350127
350128
350182
350130
350195
350196
350133
350134
350135
350375
350374
350138
350167
350168
350171
350173
350174
350175
350176
350178
350179
350181
400217
500114
600115
9201078
400570
500181
350288
8171003
350301
810736
830503
400268
400424
900327
890132
8024061
8024043
8024039
800177
8164005
8160001
8160003
8161042
8160002
8041008
8041052
8042026
8172015
430298
8041030
400164
8171004
8171006
8161044
400164
350266
520031
350346
1
1
1
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
1
1
2
1
1
1
1
2
1
2
1
1
1
1
1
1
1
1
1
1
1
2
2
1
1
6
1
1
1
1
2
1
2
4
2
5
1
1
5
9
3
19
1
1
4
1
1
4
1
8
5
4
1
4
2
4
8172009
360218
8171002
2
2
1
8172009
360218
8171002
2
2
1
8172009
360218
8171002
2
2
1
19
8172009
360218
8171002
2
2
1
PR550T
QTY
PR550HT
QTY
PR600S
QTY
Part No.
350101-01
350102
350236
350362
350107
350354
350114
350115
350116
350118
350119
350194
350121
350309
350125
350126
350127
350128
350182
350130
350195
350196
350133
350134
350135
350375
350374
350138
350167
350168
350171
350173
350184
350175
350176
350178
350179
350181
400217
500114
350197
9201078
400570
500181
1
1
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
1
1
2
1
1
1
1
2
1
2
1
1
1
1
1
1
1
1
1
1
1
1
2
1
Part No.
350101
350339
350102
350236
350362
350107
350354
350114
350115
350116
350118
350119
350194
350121
350309
350125
350126
350127
350128
350182
350130
350195
350196
350133
350134
350135
350375
350374
350138
350167
350168
350171
350173
350174
350175
350176
350178
350179
350181
400217
500114
600115
9201078
400570
500181
1
1
1
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
1
1
2
1
1
1
1
2
1
2
1
1
1
1
1
1
1
1
1
1
1
2
2
1
Part No.
350101
350339
350102
350103
350104
350107
350354
350114
350115
350116
350118
350119
350194
350121
350309
350125
350126
350127
350128
350182
350130
350195
350196
350133
350134
350135
350375
350374
350138
350167
350168
350171
350173
350174
350175
350176
350178
350179
350181
400217
500114
600115
350307
9201078
400570
500181
1
1
1
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
1
1
2
1
1
1
1
2
1
2
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
8171003
350301
810736
830503
400268
400424
900327
890132
8024061
8024043
8024039
800177
8164005
8160001
8160003
8161042
8160002
8041008
8041052
8042026
8041030
400164
8171004
8171006
8160005
400164
350266
520031
350346
8
1
1
1
1
2
1
2
4
2
5
1
1
5
9
3
19
1
1
3
4
1
8
5
4
1
4
2
4
8171003
350301
810736
830503
400268
400424
900327
890132
8024061
8024043
8024039
800177
8164005
8160001
8160003
8161042
8160002
8041008
8041052
8042026
8172015
430298
8041030
400164
8171004
8171006
8160005
400164
350266
520031
350346
5
1
1
1
1
2
1
2
4
2
5
1
1
5
9
3
19
1
1
4
1
1
4
1
8
5
4
1
4
2
4
8171003
350301
810736
830503
400268
400424
900327
890132
8024061
8024043
8024039
800177
8164005
8160001
8160003
8161042
8160002
8041008
8041052
8042026
8172015
430298
8041030
400164
8171004
8171006
8160005
400164
350266
520031
350346
5
1
1
1
1
2
1
2
4
2
5
1
1
5
9
3
19
1
1
4
1
1
4
1
8
5
4
1
4
2
4
350363
8172009
360218
8171002
1
2
2
1
350363
8172009
360218
8171002
1
2
2
1
350363
8172009
360218
8171002
1
2
2
1
OS600S
QTY
Part No.
350101
350339
350102
350103
350104
350107
350113
350114
350115
350116
350118
350119
350194
350121
350309
350125
350126
350127
350128
350182
350130
350195
350196
350133
350134
350135
350375
350374
350138
350167
350168
350171
350173
350174
350175
350176
350178
350179
350181
400217
500114
600115
350307
9201078
400570
500181
350288
8171003
350301
810736
830503
400268
400424
900327
890132
8024061
8024043
8024039
800177
8164005
8160001
8160003
8161042
8160002
8041008
8041052
8042026
8172015
430298
8041030
400164
8171004
8171006
8161044
400164
350266
520031
350346
1
1
1
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
1
1
2
1
1
1
1
2
1
2
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
1
6
1
1
1
1
2
1
2
4
2
5
1
1
5
9
3
19
1
1
4
1
1
4
1
8
5
4
1
4
2
4
8172009
360218
8171002
2
2
1
Form No F021108D
PR & OS Owner’s Manual
MAINTENANCE RECORD
Date
Part No 350324
Service Performed
20
Form No F021108D