Bissell 1690 Vacuum Cleaner User Manual

User’s Guide
Models 1690 and 1695
■ Assembly
■ Operation
■ Safety
■ Storage
TM
Thanks for buying a BISSELL POWERSTEAMER Upright Deep Cleaner.
We’re glad you purchased a BISSELL POWERSTEAMER™
Upright Deep Cleaner. Everything we know about floor care
went into the design and construction of this complete,
high-tech home cleaning system.
Your POWERSTEAMER™ is well made, and we back it
with a full one-year warranty. We also stand behind it with a
knowledgeable, dedicated Consumer Services department,
so, should you ever have a problem, you’ll receive
fast, considerate assistance.
My great-grandfather invented the floor sweeper
in 1876. Today, BISSELL is a global leader in the design,
manufacture, and service of high
quality homecare products like
your POWERSTEAMER.™
Thanks again, from
all of us at BISSELL.
Mark J. Bissell
President and Chief Executive Officer
SmartClean System
TM
Multi-motor system for more
cleaning power
■ SmartMixTM automatically adjusts
formula to specific cleaning need
■ Floating brush suspension adjusts
to all floor surfaces
■ On-board tools for above
floor cleaning
■
IMPORTANT SAFETY INSTRUCTIONS
WARNING:
When using an electrical
appliance, basic precautions should be
observed, including the following: Read all
instructions before using your POWERSTEAMER.TM
To reduce the risk of electric shock, use indoors
only. Do not immerse. Use only on surfaces
moistened by cleaning process. Always connect to
a properly grounded outlet. Unplug from outlet
when not in use and before conducting
maintenance or troubleshooting.
■ Do not leave machine when it is plugged in
■ Do not service machine when it is plugged in
■ Do not use with damaged cord or plug
■ Do not use machine if it has been dropped,
damaged, left outdoors or dropped into water
■ Do not expose to rain, store indoors.
■ Do not handle unit with wet hands
■ Do not pull or carry by cord, use cord as a
handle, close door on cord, pull cord around
sharp corners or edges, run appliance over
cord, or expose cord to heated surfaces
■ Do not carry the appliance while in use
■ Do not unplug by pulling on cord-unplug by
grasping plug
■ Do not handle plug or appliance with wet hands
■ Do not put any object into appliance openings,
use with blocked opening, or restrict air flow
■ Do not expose hair, loose clothing, fingers or
body parts to openings or moving parts
■ Do not pick up hot or burning objects
■ Do not pick up flammable or combustible
materials (lighter fluid, gasoline, kerosene, etc.)
or use in the presence of explosive liquids or vapor
■ Do not use appliance in an enclosed space filled
with vapors given off by oil base paint, paint
thinner, some moth proofing substances,
flammable dust, or other explosive or toxic vapors
■ Do not pick up toxic material (chlorine bleach,
ammonia, drain cleaner, gasoline, etc.)
■ Do not modify the 3-prong grounded plug
■ Do not allow to be used as a toy
■ Do not use for any purpose other than described
in this User’s Guide
■
■
■
■
■
■
■
■
Use only manufacturer’s recommended
attachments
Use only cleaning products formulated by
BISSELL for use in this appliance
Keep openings free of dust, lint, hair, etc.
Keep appliance on a level surface
Turn off all controls before unplugging
Unplug by grasping the plug, not the cord
Be extra careful when cleaning stairs
Pay close attention when working around
children
SAVE THESE INSTRUCTIONS.
THIS MODEL IS FOR HOUSEHOLD USE ONLY.
GROUNDING INSTRUCTIONS
This appliance must be connected to a grounded
wiring system. If it should malfunction or break
down, grounding provides a safe path of least
resistance for electrical current, reducing the risk of
electrical shock. The cord for this appliance has an
equipment-grounding conductor and a grounding
plug. It must only be plugged into an outlet that is
properly installed and grounded in accordance with
all local codes and ordinances.
Grounded
Outlets
Grounding Pin
WARNING: Improper connection
of the equipment-grounding conductor can
result in a risk of electrical shock. Check
with a qualified electrician or service person
if you aren’t sure if the outlet is properly
grounded. DO NOT MODIFY THE PLUG.
If it will not fit the outlet, have a proper
outlet installed by a qualified electrician.
This appliance is designed for use on a
nominal 120-volt circuit, and has a
grounding attachment plug that looks like
the plug in the drawing above. Make certain
that the appliance is connected to an
outlet having the same configuration as
the plug. No plug adapter should be used
with this appliance.
2
1.
Handle
Assembly
4.
Upper Hose
Rack
Upholstery/
Carpet Tool
Bolt and Nut
(2)
Lower
Chassis
3.
Flex Hose
Assembly
5.
Upper
Cord
Holder
Spraying
Crevice
Tool
2. Power
Cord
Lower
Cord
Holder
Lower
Hose
Rack
Back View
3
How to use this guide
This User’s Guide has been designed to help you get
maximum satisfaction from your POWERSTEAMERTM
Upright Deep Cleaner. You’ll find assembly
instructions for all cleaning tasks, safety
precautions, pre-cleaning tips, and maintenance
and troubleshooting instructions. Please read this
Guide thoroughly before assembling your cleaner.
Pay particular attention to the assembly diagram,
assembly instructions, and part names. Locate and
organize all parts before assembly. Familiarize
yourself with the parts and where they go.
Following the Guide will greatly enhance your
ability to get top performance from your cleaner
for many years.
How to put it together
The only thing you will need to assemble your cleaner
is a Phillips head
screwdriver.
Your POWERSTEAMERTM is packaged as two
primary components–the Lower Chassis and the
Handle Assembly. Also included is a 10’ Flex Hose
Assembly and Upholstery/Carpet Tool. Additional
attachments are included on some models.
1.
Handle Assembly. Slide Handle Assembly (with
attached Hose Rack/Cord Holder) down onto Lower
Chassis until it will go no further. Secure by placing
two (2) Phillips Head
bolts into front of Handle
Assembly and into hex nuts at back of Lower Chassis
unit, as shown.
2.
Power Cord. Wrap Power Cord around upper and
lower Cord Holders, and secure Plug to Cord with
molded clip.
NOTE: Your POWERSTEAMERTM features a Cord
Quick-Release. To easily release Power Cord, rotate
upper Cord Holder and remove Cord. Use clip at
back of Handle Assembly to secure Power Cord
when using cleaner.
3.
Flex Hose Assembly. Coil Flex Hose Assembly on
back of POWERSTEAMER,TM using the hose racks
to guide and secure the Hose.
4.
Upholstery/Carpet Tool. Connect Upholstery/
Carpet Tool to end of Flex Hose Assembly by
depressing the button at the end of the Hose.
Slide the Tool over the Hose end until the button
snaps into place in hole in Tool. Secure Hose/Tool
unit in clamp at upper right side.
5.
Spraying Crevice Tool. Clip Spraying Crevice
Tool to Flex Hose Assembly just below the
Upholstery/Carpet Tool using the Spraying
Crevice Tool Hose Clip.
Assembly is now complete.
4
Index
How to begin...
Safety instructions . . . . . . . . . .2
Product view . . . . . . . . . . . . . .3
Deep cleaning carpet
1. Plan activities to give carpet time to dry.
2. Remove easily moved furniture (chairs, lamps, coffee/
cocktail tables, etc.) from room.
3. Vacuum carpet thoroughly.
4. Decide where to begin–and end–your job. Clean in 3’x 4’
sections, starting in areas farthest from exit. Plan to leave a
path open to empty soiled water and refill cleaner.
5. Carpeting will dry in three to four hours, depending on carpet
style and air circulation in room. A floor fan speeds drying.
6. Replace furniture on damp carpeting by placing waxed
paper under furniture legs until floor dries completely.
How to begin . . . . . . . . . . . . . .5
Index . . . . . . . . . . . . . . . . . . . .5
Deep cleaning carpet . . . . . .6-7
Cleaning upholstery
& small areas . . . . . . . . . . . .8-9
Cleaning bare floors . . . . .10-11
Putting it away . . . . . . . . . . . .11
Troubleshooting . . . . . . . . . . .12
Deep cleaning upholstery
Parts . . . . . . . . . . . . . . . . . . .13
1. Check manufacturer’s tag before cleaning. “W” or “WS” on
the tag means you can use your POWERSTEAMER.TM If tag is
coded with an “X” or “S” (with diagonal strike-through), or
says “Dry Clean Only,” do not proceed. Do not use on velvet
or silk.
2. If manufacturer’s tag is missing or not coded, check with
your furniture dealer.
3. Check for colorfastness in an inconspicuous place.
4. If possible, check upholstery stuffing. Colored stuffing may
bleed through fabric when wet.
Always vacuum thoroughly before
you deep clean. If possible, move
larger furniture to an area you
will not be cleaning.
How to put it together . . . . . . .4
Warranty . . . . . . . . . . . . . . . .14
Consumer services . . . . . . . . .14
Tip:
Deep cleaning
carpeting and
upholstery
regularly can
reduce dust and
allergens in
your home.
5
How to deep clean carpet
Getting ready
Pre-treating (optional)
1. Unfasten the Clean Water Tank Latch Assembly by lifting
from the bottom with your fingers.
2. Remove Clean Water Tank Assembly by sliding it up the
Handle Assembly until it comes free.
3. Take Clean Water Tank to sink area, remove Clean Water
Tank Cap and fill Tank with hot (NOT boiling) tap water
to fill line. Replace Cap securely.
4. Remove SmartMix TM Formula Tank Assembly from Clean
Water Tank Assembly by grasping bottom with fingers and
sliding it out.
5. Unscrew SmartMixTM Formula Tank Cap and Insert
Assembly and add BISSELL Fiber Cleansing FormulaTM to fill
line. Reclose Cap tightly.
6. Slide SmartMixTM Formula Tank Assembly back into position
in Clean Water Tank Assembly.
7. Replace Clean Water Tank Assembly by sliding Tank down
the front of the Handle Assembly until it fits snugly against
top of Lower Chassis. Secure with Clean Water Tank
Latch Assembly.
8. Select SmartCleanTM setting.
■ WATER ONLY - Use for gentle cleaning of delicate
fabrics, or for (optional) rinsing following cleaning.
■ NORMAL - Water and Fiber Cleansing Formula are mixed
to optimize normal cleaning. Use for everyday dirt and
soil conditions.
■ HIGH TRAFFIC - Water and Fiber Cleansing Formula are
mixed to optimize heavy cleaning. Use for entryways,
hallways, heavy soil and stains. This setting may require
more frequent refilling on the SmartMixTM bottle.
9. Unwrap Power Cord from Cord Holder and plug into
120 Volt, 60 Hz grounded outlet as described in Important
Safety Instructions, page 2.
If cleaner starts when first plugged in, switch cleaner OFF (O)
until ready for use.
Pre-treat highly soiled carpet, such as hallways
and other high-traffic areas.
1. Move POWERSTEAMERTM to an area to be
cleaned.
2. Move 3-position Power Switch to the
PRE-TREAT ( I ) position to activate solution
pump.
3. Press Release Pedal on Left side of Lower
Chassis with foot.
4. Pull Trigger on Handle Assembly to spray
cleaning solution as you move cleaner over
soiled areas.
5. Slowly move cleaner back and forth over carpet surface one time while depressing Trigger.
Do not overwet.
6. Wait 5 - 10 minutes before full cleaning.
6
WARNING:
Use
only BI SSEL L Fibe r
Cleansing Formula ™ i n
your POWERSTEAMER.™
Use of cleaning formulas
which contain lemon
or pine oil may damage
this appliance and void
w a r r a n t y. Chemical spot
cleaners or solventbased soil removers
should not be used.
These products may
react with the plastic
materials used in your
POWERSTEAMER,™ causing
cracking or pitting.
Deep cleaning
1. Move Power Switch to CLEAN ( II ) position to activate
solution pump and vacuum motor.
2. Press Release Pedal on left side of Lower Chassis with foot.
3. Slowly move cleaner back and forth over carpet surface
one time while depressing Trigger. Do not overwet.
4. Repeat motion over same area without depressing Trigger.
5. Repeat Steps 3 and 4 until no more dirt can be removed.
6. Continue to clean entire carpet, working in
3’ x 4’ sections.
7. Empty the Dirty Water Tank Assembly when dirty water
reaches the full line.
8. If the machine loses suction and/or motor noise rises in
pitch, turn Power Switch to OFF. Check the Dirty Water
Tank Assembly and empty the tank if it is full [see WHEN
YOU’RE DONE, page 7].
9. If floor nozzle stops spraying, turn Power Switch to OFF and
check water and cleaning solution levels. Refill if needed.
Never run POWERSTEAMER TM dry.
When you’re done
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
Turn Power Switch to OFF (O) position.
Unplug Power Cord from outlet.
Remove and empty Clean Water Tank Assembly.
Press Release Pedal and tip Handle Assembly back with
Handle Assembly.
Release Dirty Water Tank Latch Assembly at bottom of
Lower Chassis.
Carefully lift Dirty Water Tank Assembly from Lower
Chassis using Carry Handle Assembly.
Carry Tank to a toilet or sink, turn Circular Cap at back of
unit counterclockwise to open, and pour to empty.
Fill Dirty Water Tank Assembly with clean water. Rinse
thoroughly and discard water.
Remove Dirty Water Tank Triangle Lid and flush suction
opening with clean water. Replace cover. Replace Circular
Cap by turning clockwise.
Replace Clean Water Tank Assembly on Handle Assembly
and secure with side latches.
Replace Dirty Water Tank Assembly on Lower Chassis and
secure with Clean Water Tank Latch Assembly.
See PUTTING IT AWAY on page 11.
Tip:
Deep cleaning
stairs and high
traffic areas on a
regular basis can
prolong carpet
life.
WARNING:
The
Dir ty Water Ta n k
A ss embly h olds
approximately one
gallon of soiled liquid.
A special float device
in the tank will cause
the cleaner to stop
removing solution from
carpet, and the motor
sound to rise in pitch
when the Dirty Wa t e r
Tank Assembly is full.
Failure to empty full
tank will damage unit.
7
How to clean upholstery and small areas
Getting ready
Tip:
Check upholstery
stuffing before
cleaning.
Colored stuffing
may bleed
through fabric
when wet.
8
1. Unfasten the Clean Water Tank Assembly by lifting from
the bottom with your fingers.
2. Remove Clean Water Tank Assembly by sliding it up the
Handle Assembly until it comes free.
3. Remove Flex Hose Assembly from back of unit.
4. Tip Handle Assembly back by pressing Release Pedal
on left side of Lower Chassis and pulling back on
Handle Assembly.
5. Lift Dirty Water Tank Triangle Lid by pulling back on rear
latch with finger.
6. Place triangle-shaped end of Flex Hose Assembly in Dirty
Water Tank Triangle port by placing wide (bottom) end in
first, then pushing latch end in until it snaps into place.
7. Tip Handle Assembly back to its full upright position.
8. Place Solution Tube Connector into the port at the lower
left side of the Handle Assembly. Place tabs on Connector
into notches in port, then turn clockwise to secure. Make
certain Solution Tube is securely fastened to Connector.
9. Select Upholstery/Carpet Tool or Spraying Crevice Tool,
and attach to Flex Hose Assembly using the “button-inhole” method.
10. Take Clean Water Tank to sink area, remove Clean Water
Tank Cap and fill Tank with hot (NOT boiling) tap water
to fill line. Replace Cap securely.
11. Remove SmartMixTM Formula Tank Assembly from Clean
Water Tank Assembly by grasping bottom with fingers and
sliding it out.
12. Unscrew SmartMixTM Formula Tank Cap and Insert
Assembly and add BISSELL Fiber Cleansing FormulaTM to
fill line. Reclose Cap tightly
13. Slide SmartMixTM bottle back into position in Clean Water
Tank Assembly.
14. Replace Clean Water Tank Assembly. Slide Tank down front
of Handle Assembly until it fits snugly against top of Lower
Chassis. Secure with Clean Water Tank Latch Assembly.
WARNING:
15. Select SmartCleanTM setting.
• WATER ONLY - Use for gentle cleaning of delicate
fabrics, or for (optional) rinsing following cleaning.
• NORMAL - Water and Fiber Cleansing Formula are
mixed to optimize normal cleaning. Use for everyday
dirt and soil conditions.
• HIGH TRAFFIC - Water and Fiber Cleansing Formula are
mixed to optimize heavy cleaning. Use for entryways,
hallways, heavy soil and stains.
This setting may require more frequent refilling on the
SmartMixTM bottle.
16. Unwrap Power Cord from Cord Holder and plug into
120 Volt, 60 Hz grounded outlet as described in Important
Safety Instructions, page 2.
If cleaner starts when first
plugged in, switch off until
ready for use.
Do
not lay unit on its
back with Clean
Water Tank Assembly
in place. Do not tip
up foot with Dirty
Water Tank Assembly
in place.
WARNING:
Use
onl y B ISSE LL Fi ber
Cleansing Formula ™ i n
your POWERSTEAMER.™
Use of cleaning formulas
which contain lemon
or pine oil may damage
this appliance and void
w a r r a n t y. Chemical spot
cleaners or solventbased soil removers
should not be used.
These products may
react with the plastic
materials used in your
POWERSTEAMER,™ causing
cracking or pitting.
Cleaning
1. Slowly move Upholstery/Carpet Tool back and
forth over soiled surface, first using spray only,
then spray and vacuum, finishing with
vacuum only.
NOTE: Use the Spraying Crevice Tool [optional
on some models] to spray cleaning solution and
remove soil from areas too small to be reached
with the Upholstery/Carpet Tool.
2. Continue to clean soiled area, working in
small sections, until no more dirt can be
removed. Do not overwet.
3. If the machine loses suction and/or motor
noise rises in pitch, turn Power Switch to OFF.
Check the Dirty Water Tank Assembly and
empty the tank if it is full [see WHEN YOU’RE
DONE, page 7].
4. If spray tip stops spraying, turn Power Switch
to OFF and check water and cleaning solution
levels. Refill if needed.
Never run POWERSTEAMERTM dry.
9
How to clean bare floors
Getting ready
NOTE: Your POWERSTEAMERTM is not recommended for
cleaning wood floors.
■ Use only BISSELL Floor Cleansing FormulaTM on
no-wax floors. Never use BISSELL Fiber Cleansing
FormulaTM or other carpet cleaners on bare floors.
■ Sweep before starting.
■ Remove old wax before cleaning.
■ Leave an exit path.
■ Allow at least 1/2 hour drying time.
3.
Bare Floor
Bottom Front Edge of
Lower Chassis Snap Together Cleaning
Tool
WARNING:
Use
only BI SS ELL Fi ber
Cleansing Formula ™ i n
your POWERSTEAMER.™
Use of cleaning formulas
which contain lemon
or pine oil may damage
this appliance and void
w a r r a n t y. Chemical spot
cleaners or solventbased soil removers
should not be used.
These products may
react with the plastic
materials used in your
POWERSTEAMER,™ causing
cracking or pitting.
10
1. Remove Clean Water Tank Assembly and Dirty Water
Tank Assembly.
2. Tip POWERSTEAMERTM back for easier access to Nozzle.
3. Attach Bare Floor Cleaning Tool to Nozzle with strip facing
forward, as shown. Align front edges and snap together.
4. Tip Handle Assembly back by pressing Release Pedal on left
side of Lower Chassis and pulling back on Handle Assembly.
5. Take Clean Water Tank to sink area, remove Clean Water
Tank Cap and fill Tank with hot (NOT boiling) tap water
to fill line. Replace Cap securely.
6. Remove SmartMixTM Formula Tank Assembly from Clean
Water Tank Assembly by grasping bottom with fingers and
sliding it out.
7. Unscrew SmartMixTM Formula Tank Cap and Insert
Assembly and add BISSELL Floor Cleansing FormulaTM to
fill line. Reclose Cap tightly.
8. Slide SmartMixTM bottle back into position in Clean Water
Tank Assembly.
9. Replace Clean Water Tank Assembly. Slide Tank down front
of Handle Assembly until it fits snugly against top of Lower
Chassis. Secure with Clean Water Tank Latch Assembly.
10. Replace Dirty Water Tank Assembly.
11. Select SmartCleanTM setting.
■ WATER ONLY - Use for gentle cleaning, or for (optional)
rinsing following cleaning.
■ NORMAL - Water and Floor Cleansing FormulaTM are
mixed to optimize normal cleaning. Use for everyday
dirt and soil conditions.
■ HIGH TRAFFIC - Water and Floor Cleansing FormulaTM
are mixed to optimize heavy cleaning. Use for
entryways, hallways, heavy soil and stains. This
setting may require more frequent refilling on the
SmartMixTM bottle.
13. Unwrap Power Cord from Cord Retainer and
plug into 120 Volt, 60 Hz grounded outlet as
described in Important Safety Instructions,
page 2.
Cleaning
1. Slowly move the Bare Floor Cleaning Tool
back and forth over soiled surface one time
while depressing Trigger.
Do not overwet.
2. Repeat motion over same area without
depressing Trigger.
3. Repeat Steps 1 and 2 until no more dirt can
be removed.
4. If machine loses suction and/or noise rises in
pitch, turn Power Switch to OFF. Check the
Dirty Water Tank Assembly and empty the
tank if it is full (see WHEN YOU’RE DONE,
page 7).
5. If spray tip stops spraying, turn Power Switch
to OFF and check water and cleaning solution
levels. Refill if needed.
Never run POWERSTEAMER ™ dry.
WARNING:
The
Di rt y Wa te r Ta n k
Assem bly holds
approximately one
gallon of soiled liquid.
A special float device
in the tank will cause
the cleaner to stop
removing solution from
carpet, and the motor
sound to rise in pitch
when the Dirty Wa t e r
Tank Assembly is full.
Failure to empty full
tank will damage unit.
WARNING:
Do n o t
lay unit on its back with
Clean Water Tank Assembly
in place. Do not tip up
foot with Dirty Wa t e r
Tank Assembly in place.
Putting it away
1. Follow instructions in WHEN YOU’RE DONE, page 7.
2. Disconnect Solution Tube Connector by turning it counterclockwise and gently pulling it straight from port.
3. Remove Flex Hose Assembly from Dirty Water Tank
Triangle port.
4. Replace Dirty Water Tank Triangle Lid.
5. Coil Flex Hose Assembly in Hose Rack on back
of POWERSTEAMER.TM
6. Rinse Tools in clean running water, dry, and replace as
shown in HOW TO PUT IT TOGETHER, page 4.
7. Wrap Power Cord around Cord Holder on back of
POWERSTEAMER.TM
8. Wipe all surfaces with a soft cloth.
9. Store cleaner upright in a protected, dry area.
NOTE: You may have water remaining in the Clean Water
Tank Assembly, and BISSELL Fiber Cleansing FormulaTM
remaining in the SmartMix ® dispenser. Never leave clean
water in the Clean Water Tank Assembly or soiled
solution in the Dirty Water Tank Assembly.
11
Troubleshooting
Reduced spray or no spray
WARNING:
To reduce the risk of
fire, electric shock or
injury unplug from
outlet before servicing.
Possible Causes
Remedies
Clean Water Tank Assembly empty
Refill Tank
SmartMixTM dispenser empty
Fill with BISSELL Fiber Cleansing
FormulaTM
Spray Nozzle clogged
Clean Spray Nozzle
Pump not operating properly
Check electrical plug
Power switch on?
Turn POWERSTEAMERTM off and hold
Trigger for 10-15 seconds. Turn Power
Switch to“CLEAN” position and hold
trigger for10-15 seconds
Call BISSELL Consumer Services
Vacuum not picking up cleaning solution
12
Possible Causes
Remedies
Loose Triangle Cap
Check cap and snap securely into Dirty
Water Tank Assembly
Dirty Water Tank Assembly
not aligned/secured
Check Tank for proper alignment and
secure with side latches
Flex Hose Assembly not secure
Check fit of Hose at Vacuum Port
connections [Upholstery/Carpet Tool only]
Poor Tool position
[Upholstery/Carpet Tool only]
Adjust angle; apply more downward
pressure
Dirty Water Tank Assembly is full
Empty Dirty Water Tank Assembly
Part numbers and descriptions
Item Part No. Part Name
1
010-9200
2
010-9201
3
4
5
603-0966
603-0961
603-0910
6
7
8
9
10
11
12
603-0911
603-0912
603-6110
010-9148
603-0905
010-9130
603-9040
13
010-1645
14
603-1640
15
014-9025
16
013-2856
17
010-7055
18
603-7075
Flex Hose Assembly with
4” Upholstery/Carpet Tool
4” Upholstery/Carpet Tool
Assembly
4” Removable Brush
4” Window
6” Upholstery/Carpet Tool
Assembly
6” Removable Brush
6” Window
Spray Tips (2)
Spraying Crevice Tool
Hose Clip
Bare Floor Cleaning Tool
Clean Water Tank
Assembly
Clean Water Tank
Filler Cap
Clean Water Tank Cap
and Insert Assembly
Dirty Water Tank
Assembly
Dirty Water Tank
Triangle Cap
Dirty Water Tank
Drain Cap
Bolts and Nuts
(2 each)
1
18
10
13
12
16
15
NOTE: To order replacement parts, or
to order parts not originally included in
your POWERSTEAMER™ model, call
BISSELL Consumer Services
9
1-800-237-7691
Monday - Friday 8 a.m. — 7 p.m. EST
Saturday
9 a.m. –– 1 p.m. EST
5, 6, 7
8
2, 3, 4
14
17
11
13
About your warranty
This warranty gives you specific legal rights, and you may
also have other rights which may vary from state to state.
If you need additional instruction regarding this warranty
or have questions regarding what it may cover, call
BISSELL Consumer Services.
One Year Warranty
BISSELL Inc., upon receipt of the product, will repair or
replace, free of charge, any part which is defective or
malfunctioning within one year of the purchase date,
provided that it is used for personal and not commercial
or rental service. If the deep cleaner cannot be repaired,
BISSELL Inc. will replace or refund the full price.
If your BISSELL product should require service
1. Call BISSELL Consumer Services (1-800-237-7691)
for referral to an authorized BISSELL Service
Center.
2. If there is not an authorized BISSELL Service
Center in your area, a BISSELL Consumer
Services Representative will issue you a Return
Authorization Number.
3. Return the machine with a photocopy of proof of
purchase. (Your dated sales receipt is your
warranty – do not send original. )
Insure the machine when shipping for your protection from loss.
BISSELL Consumer Services
For information about repairs or replacement parts, or questions
about your warranty, call:
BISSELL Consumer Services
1-800-237-7691
Monday - Friday 8 a.m. — 7 p.m. EST
Saturday
9 a.m. — 1 p.m. EST
Or write:
BISSELL INC
PO Box 3606
Grand Rapids MI 49501
ATTN: Consumer Services
When contacting BISSELL, have model number of unit available.
Please record your Model Number: ___________________
Please record your Purchase Date: ___________________
NOTE: Please keep your original sales receipt. It is your warranty.
14
©1997 BISSELL Inc
Grand Rapids, Michigan
All rights reserved. Printed in China
Part Number 010-5710