Bissell 30C7 Vacuum Cleaner User Manual

Earn BISSELL Rewards!
Register your
product today!
See details on
back page
USER'S GUIDE
30C7 SERIES
2
Thank You
3
Safety Instructions
4
Product View
5-6
Assembly
6-9
Operations
10-15
Maintenance and Care
16-17
Troubleshooting
18
Replacement Parts
18
Accessories
19
Warranty
20
Product Registration
20
Consumer Services
Thanks for buying a BISSELL OptiClean® Vacuum
We’re glad you purchased a BISSELL OptiClean vacuum. Everything
we know about floor care went into the design and construction of
this complete, high-tech home cleaning system.
Your BISSELL OptiClean vacuum is well made, and we back it with a
limited three year warranty. We also stand behind it with a knowledgeable, dedicated Consumer Services department, so, should you
ever have a problem, you’ll receive fast, considerate assistance.
My great-grandfather invented the floor sweeper in 1876. Today,
BISSELL is a global leader in the design, manufacture, and service of
high quality homecare products like your BISSELL vacuum.
Thanks again, from all of us at BISSELL.
Mark J. Bissell
Chairman, President & CEO
2
www.bissell.com800.237.7691
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic
precautions should be observed, including
the following:
Read all
instructions
before using your
Upright VACUUM.
Always connect to a polarized outlet
(left slot is wider than right). Unplug from
outlet when not in use and before conducting
maintenance.
WARNING: To
reduce the risk of fire,
electric shock, or injury:
■ Keep hair, loose clothing, fingers, and all
■
■
■
■
■
■
■ Do not modify the polarized plug to fit a
non-polarized outlet or extension cord.
■ Do not leave vacuum cleaner unattended
when it is plugged in.
■ Unplug from outlet when not in use and
■
■
before servicing.
■ Do not use outdoors or on wet surfaces.
■ Do not allow children to operate vacuum
parts of body away from openings and
moving parts.
Turn off all controls before plugging or
unplugging vacuum cleaner.
Use extra care when cleaning stairs.
Unplug before attaching the TurboBrush® Tool
Do not pick up flammable materials
(lighter fluid, gasoline, kerosene, etc.) or
use in the presence of explosive liquids
or vapors.
Do not pick up toxic material (chlorine
bleach, ammonia, drain cleaner, etc.).
Do not use vacuum cleaner in an
enclosed space filled with vapors given
off by oil base paint, paint thinner, some
moth proofing substances, flammable
dust, or other explosive or toxic vapors.
Do not pick up hard or sharp objects
such as glass, nails, screws, coins, etc.
Do not pick up anything that is burning or
smoking, such as cigarettes, matches, or
hot ashes.
Do not use without filters in place.
Use only on dry, indoor surfaces.
Keep appliance on a level surface.
Do not carry the vacuum cleaner while it
is running.
Brush may unexpectedly restart. Unplug
from outlet when cleaning or servicing
■ Close attention is necessary when used
■
■
■
■
■ Do not use for any purpose other than
■
■
SAVE THESE
INSTRUCTIONS
FOR FUTURE USE
THIS APPLIANCE
HAS A POLARIZED
PLUG.
cleaner or use as a toy.
by or near children.
■
■
■
■
■
■
described in this user’s guide.
Use only manufacturer’s recommended
attachments.
Do not use with damaged cord or plug.
If appliance is not working as it should,
has been dropped, damaged, left outdoors, or dropped into water, have it
repaired at an authorized service center.
Do not pull or carry by cord, use cord as
a handle, close a door on cord, or pull
cord around sharp edges or corners. Do
not run appliance over cord. Keep cord
away from heated surfaces.
Do not unplug by pulling on cord. To
unplug, grasp the plug, not the cord.
Do not handle vacuum cleaner or plug
with wet hands.
Do not put any object into openings. Do
not use with any opening blocked; keep
openings free of dust, lint, hair, and
anything that may reduce air flow.
To reduce the risk of electric shock, this
appliance has a polarized plug (one blade
is wider than the other). This plug will fit in
a polarized outlet only one way. If the plug
does not fit fully in the outlet, reverse the
plug. If it still does not fit, contact a qualified
electrician to install a proper outlet. Do not
change the plug in any way.
This model is for household use only.
www.bissell.com800.237.7691
3
Product view
TurboBrush® Tool
(30C7 model)
Pet TurboBrush® Tool
(30C7T model)
Carry Handle
Power Switch
Brush On/Off
Inner Cyclone
Screen
Upper Tank
Easy Empty
Dirt Container
Pre-Motor Filter
Foot Window
Pet Contour
Tool®
(30C7T model)
Dusting/
Upholstery Tool
(30C7 model)
Lock ‘n Seal®
Lever
Post-Motor
Filter
Stretch Hose
Crevice Tool
Extension
Wand
Brush
Wide Cleaning Foot
NOTICE:
Product images may
vary between models.
4
Handle Release
Pedal
www.bissell.com800.237.7691
Assembly
The only tool you’ll need to assemble
your vacuum cleaner is a Phillips head
screwdriver.
Attach handle to vacuum
1. Locate the bag that contains the extension
wand support, lower cord wrap, and screws.
Remove the screw packet from the bag.
Caution:
Do not plug in your vacuum
cleaner until you are familiar
with all instructions and
operating procedures.
2
2. Stand the vacuum upright and from the
rear of the unit, slide the base of the
handle firmly into the grooves at the top of
the vacuum body.
3. Ensure that the handle is firmly attached to
the vacuum body. The front of the handle
should be flush with the front of the vacuum body. If there are any gaps, continue
to push the handle until it is secure.
4. Remove two of the four screws from the
screw packet. Insert one screw, into each
of the existing holes in the handle. With a
screwdriver, tighten each screw completely.
4
Attach storage clips, tool, and vacuum hose
1. Locate the bag that contains the extension wand support, lower cord wrap, and
remaining two screws.
2. Attach the extension wand support to the
rear of the unit. Extension wand support
should be placed about half way down
the vacuum body. Using one of the two
remaining screws, insert one screw into the
existing hole. With a screwdriver, tighten
screw completely.
3. Attach the lower cord wrap to the rear of
the unit. Lower cord wrap should be placed
toward the bottom of the vacuum body.
Using the last screw, insert screw into the
existing hole. With a screwdriver, tighten
completely.
4a.Attach Twist ‘n Snap™ hose by placing the
tabbed end of the hose into the opening
of the unit, located on the left side of the
vacuum (when viewing from the back). Turn
the hose to the right to lock into place.
4a
4b.Place the attachment end of the hose into the
hole on the right side of the unit, near the
wheel.
2
3
4b
NOTE: The vacuum will not operate
effectively unless the hose is firmly
attached.
www.bissell.com800.237.7691
5
Assembly
Attach storage clips, tool, and vacuum hose continued
5. Make sure that crevice tool is inside the
extension wand. Store the extension wand
and crevice tool on the back of the unit.
Place tools on the extension wand support
and push toward the back of the unit until
clip holds tools in place.
6. Slide the dusting brush into the storage
clip on the left side of the unit (when
viewing from back.)
7. Place the TurboBrush Tool in the hole
marked “tool” on the top of the handle arch.
Operations
Handle Positions
TurboBrush®
Tool
Stretch Hose
Crevice Tool
Extension
Wand
Dusting/
Upholstery
Tool
Using your foot, press the handle
release pedal, located on the lower
left side of the vacuum, to recline
the vacuum.
Transporting your cleaner
1. To move your cleaner from room to room,
put the handle in the upright position, tilt
the cleaner back on its rear wheels and
push forward.
2. The cleaner can also be moved by using
the carry handle on the front.
1
2
Power Cord
To store power cord, wrap cord around
the upper cord wrap and lower extension
wand support. Once wound tightly use
the clip on the end of the plug to attach
the plug to the cord.
To release the power cord, rotate the upper
cord wrap down and gently pull the power
cord off of the upper cord wrap.
Power switch
The power button is located on the left
side (when viewing from back) of the
vacuum. Push the rocker switch “ON”
(I) to vacuum, and “OFF” (O) when
cleaning is complete.
6
Note: The rotating brush will not
turn on unless the unit is in the
reclined position and the brush
switch is on.
Caution:
Before using your vacuum,
Make sure both filters
(pre-motor and post-motor)
are in place. Do not operate
your vacuum without these
filters.
Power Switch
www.bissell.com800.237.7691
Operations
Brush Switch
The rotating brush is turned on or off
using the switch located next to the
power switch on the top of the tank.
When the brush switch is on, the brush
will start rotating when the unit is
reclined. The brush should be on for
most carpeted floors. You may want
to turn the brush off for bare floor
cleaning or other delicate surfaces.
Push the rocker switch “ON” (I) to turn the
brush on, and “OFF” (O) to turn brush off.
Brush Auto Shut Off Feature
When your cleaner is in the upright
position, the brush will not rotate. The
brush will rotate only when the cleaner is in the reclined position and the
brush switch is on.
Height Adjustments
There are seven height settings available for various floor surfaces. Turn
the dial on the foot of the cleaner to
the desired setting.
Lowest setting – for low pile carpet
or bare floors. To pick up debris it may
be necessary to move up one setting.
Brush Switch
Attention:
Some Frieze carpets have long
delicate fibers or threads that
may be damaged by the rotating brush during vacuuming. It is
recommended the rotating brush
be turned OFF when cleaning this
type of carpet.
While vacuuming, certain carpets
and low humidity conditions may
generate small static discharges.
The discharges are entirely harmless and are not associated in any
way with the main power supply.
Medium settings – for medium pile
carpet.
High setting – for high pile and most
shag/frieze carpet.
Note: For optimal carpet cleaning
performance, adjust to the lowest
practical setting. If your cleaner is
difficult to push, adjust to the next
higher setting.
If the dial is difficult to turn, tilt the
cleaner back slightly to take the weight
off of the foot while turning.
Some Berber carpets have a tendency
to fuzz with wear. Repeated strokes
in the same area may aggravate this
condition. Consider setting your cleaner
on a higher than normal setting for this
type of carpet.
www.bissell.com800.237.7691
7
Operations
Using the tools
Attach desired tool to hose for above floor
cleaning surfaces or hard to reach areas.
1. Remove Hose: With vacuum in upright position, remove hose end from the suction inlet
near the bottom of the vacuum by the wheel.
Do not remove “tabbed” end of hose connected to the clear tank.
2
2. Attach tools by firmly pushing onto vacuum
hose or extension wand.
2a.Dusting brush: Use brush side to dust
furniture, blinds, lamps, shelves, and
baseboards. 30C7 model only.
a.
2b.Crevice Tool: Use in tight narrow spaces
2c. Extension Wand: Use with desired
attachment for longer reach.
2d.TurboBrush® Tool: Use rotation brush
action for small flat areas such as
stairs,and furniture. Press gently down
and pull towards you in raking motion,
too much pressure will cause brush to
stop rotating.
NOTE: Model 30C7T comes with
the Pet TurboBrush® Tool and follows same operation instructions.
2e.Pet Contour Tool® (Included with 30C7T
only): Use to reach into corners and
edges on stairs as well as armrests and
other curved surfaces. The tool can be
flipped to use in any direction.
b.
c.
d.
e.
CAUTION:
To avoid personal injury
and to prevent the cleaner
from falling when cleaning stairs, always place it
at the bottom of the stairs.
8
www.bissell.com800.237.7691
Operations
Empty dirty container
Empty the dirt container as soon as the
dirt reaches the “full” line on the side of
the container.
1. Unplug the vacuum from electrical outlet.
2. Slide the Lock 'n Seal Lever to the
“Unlock” position.
2.
3. Grasp the handle and pull the dirt container
straight out to remove from the vacuum.
4. Empty dirt into garbage container.
NOTE: Emptying the dirt container
after every use will help prevent
over filling and ensure that the
vacuum is ready to go the next time
you clean.
Cleaning the dirt container
Additional steps can be taken to
clean the dirt container as necessary.
1. Ensure dirt container has been emptied.
2. While the dirt container is still out of the
unit, grasp the inner cyclone screen and
twist counterclockwise until the locking
tabs stop the rotation. Pull down the inner
cyclone screen to remove it.
3. Clean the inner cyclone with a cloth or
soft brush to remove dust or debris.
4. Wipe out the inside of the upper tank and
the inner cyclone with a damp cloth
moistened with water or a mild cleaning
solution. Let completely dry before next
use.
5. If desired, the lower dirt container may be 2
washed in warm water. Make sure it is
completely dry before reassembling.
Do not put in the dishwasher.
WARNING:
To reduce the risk of
electric shock, turn
power switch OFF and
disconnect polarized
plug from electrical
outlet before performing
maintenance or
troubleshooting checks.
4
6. To reassemble, replace the inner cyclone
screen by sliding it into the upper tank
and rotating clockwise until the locking
tabs stop the rotation. The inner cyclone
screen is labeled front and back. When
properly assembled the front graphic
should face out.
www.bissell.com800.237.7691
9
Maintenance and care
Cleaning the pre-motor filter
WARNING:
The pre-motor filter should be
checked often and washed as
needed to maintain performance.
More or less frequent cleaning may
be required based on individual
vacuuming habits and types of
debris picked up.
Do not operate cleaner
with damp or wet filters
or without all filters in
place.
1. Unplug the vacuum from electrical outlet.
2. The pre-motor filter protects the motor from
dirt particles. It is located in the slide out
tray underneath the dirt container. If the
filter becomes dirty, pull out the tray, lift
out the foam filter pad and clean it.
2
Note: The pre-motor filter may
be hand washed in cold water
with mild detergent. Rinse well
and air dry thoroughly before
replacing.
Replacing the post-motor filter cartridge
The post-motor filter assists in the
filtration process to return clean air
to the room. It is located under the
pre-motor filter tray. Unit must be
reclined to locate the post-motor
filter.
The post-motor filter cartridge
should be replaced if machine
performance is noticeably declining.
More or less frequent replacing may
be required based on individual
vacuuming habits and types of
debris picked up.
2
1. Recline the vacuum.
2. While holding the handle at a 60° angle,
push the button on the top of the postmotor filter door to unlatch. Remove the
door. Post motor filter door is located
directly below the pre-motor filter drawer.
3. If the filter is dirty, remove it and replace
with a new filter.
4. Replace the post-motor filter door.
Note: The post-motor filter is
a white, pleated filter. This filter is not washable and must
be replaced when it becomes
dirty.
10
www.bissell.com800.237.7691
Maintenance and care
Clearing Clogs
Low suction or poor pickup may be
due to a clog in the vacuum cleaner.
If you notice a change in the sound
of the motor or a reduction in the
spinning action in the dirt container,
check for a clog.
If there is no suction or if suction is
reduced at the hose, follow these
steps to check for and clear the clog.
CAUTION:
To reduce the risk of
injury from moving parts,
turn off vacuum cleaner
and disconnect power
plug from electrical outlet.
1. Turn power switch off.
2. Unplug cleaner from electrical outlet.
3. Check the pre-motor filter and clean as
necessary (see cleaning your pre-motor
filter on page 10).
4. Check the post motor filter cartridge and
replace if necessary (see replacing your
post-motor filter on page 10). Check to see
if dirt container is full. Empty if needed.
5. Check upper tank for build up or clogs.
If you notice a clog in the upper tank,
remove the inner cyclone (see cleaning the
dirt container on page 9).
6. Grasp the hose wand and separate it from
the hose wand base. Check for a clog in
the base, the wand, or in the hose.
7. Remove the Twist ‘n Snap hose from the
vacuum by turning to the left. Straighten
the hose and unclog with a long, narrow
object such as a broom handle.
8. If the clog persists, follow the instructions
for checking the rotating floor brush and
drive belt on page 13 and inspect the air
passageway for obstructions
If suction is normal in the hose,
check for and clear the clog for
floor cleaning:
1. Check the foot hose for clogs.
2. If you are not able to tell from the outside if
a clog is present, remove the screw at the
top left of the foot hose. Lay the foot hose
flat and unclog with a long, narrow object
such as a broom handle.
Remove any clogs found and fully
reassemble the cleaner before
attempting to check suction
again or using the cleaner.
www.bissell.com800.237.7691
11
Maintenance and care
Thermal motor protection
An internal thermal protector has been
designed into your cleaner to protect it
from overheating. When the thermal
protector activates, the main vacuum
motor will stop operating. If this
happens, proceed as follows.
1. Turn the cleaner OFF and unplug from
electrical outlet.
2. Check the cleaner for the source of
overheating problem (i.e. full dirt cup,
dirty filters or clog).
3. Follow the steps for checking filters and
clearing clogs on pages 10 and 11.
4. When the motor cools for approximately
30 minutes, the thermal protector
automatically resets and cleaning may
continue. If the cleaner will not turn on or
the thermal protector continues to activate,
your cleaner may need servicing. Call
BISSELL Consumer Services or visit the
website to locate an authorized Service
Center.
Note: The thermal protector controls
the main vacuum motor only, not the
brush motor. If the thermal protector activates, the brush will continue
to operate normally; however, there
will be no suction.
12
www.bissell.com800.237.7691
Maintenance and care
Check rotating floor brush and drive belt
You should check your vacuum
cleaner’s rotating floor brush and
drive belt regularly for wear and
damage. You should also clean the
brush and brush ends of strings,
hair, and carpet fibers. This type of
debris can wrap around the brush
and hamper its ability to effectively
clean your carpet. Also remove any
debris that has accumulated under
the brush cover.
1. Unplug the vacuum from electrical outlet.
2. Place handle in low position and turn
vacuum cleaner over so bottom side is facing up.
3. Remove the six screws on the sole plate
with a Phillips head screwdriver. Lift the
brush cover off.
3
4. Grasp rotating floor brush at both ends
and lift.
5. Clean string, hair, and other debris from
rotating floor brush, paying particular
attention to brush ends.
6. Check air passageway for obstructions.
Remove any debris from this area.
4
7. Clean debris from the motor pulley and
drive belt areas.
8. Check drive belt carefully for wear, cuts, or
stressed areas. If any damage is present,
discard old drive belt and replace, see
page 14.
www.bissell.com800.237.7691
13
Maintenance and care
Replace drive belt
1. Unplug the vacuum from electrical outlet.
2. With rotating floor brush removed from
vacuum cleaner (steps 1 – 4 of check rotating floor brush and drive belt page13),
grasp old drive belt and remove from
motor pulley. Discard the old drive belt.
2
3. Place one end of the new drive belt over
motor pulley and the other end over the
brush in the space between the bristles.
Note: It is important that you
use only genuine BISSELL
replacement parts. Generic
belts may not meet the exact
specifications required to keep
your vacuum operating at its
peak performance. The use of
unbranded belts could lead to
early failure of the vacuum and
could void your warranty.
3
4. Pull the brush firmly to stretch the drive
belt and place ends of brush down into
slots on sides. Turn brush several times by
hand to center the drive belt.
5. Reposition brush cover and screws.
Tighten screws securely.
Brush reset
If something becomes lodged in
the foot and the brush shuts off,
turn the cleaner off and unplug
from the outlet. Remove the
obstruction. The brush will
automatically reset when the
cleaner is plugged in and turned
back on.
14
www.bissell.com800.237.7691
Maintenance and care
TurboBrush Tool maintenance
The TurboBrush Tool should be
checked regularly for clogs or
debris wrapping around the brush.
Note: Model 30C7T comes with
the Pet TurboBrush Tool and
follows same maintenance
instructions.
1. Remove tool from hose or from vacuum.
2.
2. Twist collar so opening is at the top and
lift top cover to remove.
3. Remove the brush from the belt and clean
debris.
4. Replace the brush inside the belt and
place ends into slots on sides.
4.
5. Reposition top cover making sure to line
up inside tab at the front with the opening
on the cover. Twist collar until opening is
at the bottom to lock into place.
5.
Tip:
TurboBrush® may not be turning
due to loss of suction. Refer to
pg. 11 for checking and cleaning clogs.
www.bissell.com800.237.7691
15
Troubleshooting
Vacuum cleaner won’t turn on
Possible causes
WARNING:
To reduce the risk of electric
shock, turn power OFF and
disconnect polarized plug from
electrical outlet before performing
maintenance or troubleshooting.
Remedies
1. Power cord not plugged in
1. Check electrical plug
2. Blown fuse/tripped breaker in home
2. Check/replace fuse or reset breaker
3. Damaged power cord
3. Unplug, check for damage, have cord replaced at an
authorized service center if necessary
4. Thermal protector activated
4. Allow cleaner to cool for 30 minutes, see page 12
Vacuum cleaner and tools won't pick up dirt
Possible causes
Remedies
1. Incorrect height adjustment
1. Adjust powerfoot to correct height
2. Hose not attached to suction opening
2. Firmly push hose wand into hose wand base
3. Twist 'n Snap hose not securely attached
3. Make sure Twist 'n Snap hose is snapped into locked position
4. Crack or hole in hose
4. Check hose and replace if needed
5. Broken or worn drive belt
5. Replace drive belt, see page 14
6. Rotating floor brush bristles worn
6. Replace brush, see page 13
7. Rotating floor brush jammed
7. Remove brush and clean debris from brush ends
8. Clog in vacuum
8. Clear clogs, see page 11
9. Dirt container full
9. Empty dirt container
10. Dirt container not installed properly
10. Position correctly and lock in place
11. Filters are dirty
11. Check pre-motor and post-motor filters, see page10
12.TurboBrush® Tool is clogged or debris is wrapped
12. See page 15 for Maintaining TurboBrush® Tool
Brush not rotating
Possible causes
Remedies
1. Brush switch turned to “Off”
1. Make sure brush switch is in “On” position
2. Vacuum is in upright position
2. Recline vacuum to operate brush
3. Brush is jammed
3. Remove obstruction or debris, see page 13,
unplug cleaner to reset brush, see page 13
4. Brush needs to be reset
16
4. Unplug cleaner to reset brush, see page 14
www.bissell.com800.237.7691
Troubleshooting
Vacuum cleaner is difficult to push
Possible causes
1. Incorrect height setting
Remedies
1. Adjust powerfoot to correct height setting see, page 7
Visible dirt escaping from cleaner
Possible causes
1. Dirt container full
Remedies
1. Empty dirt container
2. Filters missing or installed incorrectly
2. Check pre-motor and post-motor filters for correct installation
see page 10
3. Dirt container installed incorrectly
3. Pull out and re-insert dirt container correctly, see page 9
Other maintenance or service not included in the manual should be
performed by an authorized service representative.
Thank you for selecting a BISSELL product.
Please do not return this product to the store.
For any questions or concerns, BISSELL is happy to be of
service. Contact us directly at 1-800-237-7691.
www.bissell.com800.237.7691
17
Replacement parts - BISSELL vacuum
Item
Part No.
1
2
3
4
Part Name
203-1520
203-1512
203-1509
203-1510
1
Drive Belt
Foot Brush Roll
Pre-Motor Foam Filter
Post-Motor Filter
2
3
4
Additional accessories
These items are available for purchase as accessories for your BISSELL
OptiClean: To purchase call 1-800-237-7691 or visit www.bissell.com.
Item
Part No.
1
2
3
4
5
6
7
1
6
18
Part Name
203-1056
203-1527
203-1429 203-1068
203-1507
203-7936
203-1291
2
Crevice Tool
Dusting Brush/Upholstery Tool
TurboBrush® Tool
Extension Wand
Twist 'n Snap Vacuum Hose
Pet TurboBrush® Tool
Pet Contour Tool®
3
4
5
7
www.bissell.com800.237.7691
Warranty - BISSELL OptiClean® Vacuum
This warranty gives you specific legal rights, and you may also have other rights which may
vary from state to state. If you need additional instruction regarding this warranty or have
questions regarding what it may cover, please contact BISSELL Consumer Services by E-mail,
telephone, or regular mail as described below.
Limited Three Year Warranty
Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, upon receipt of the product
BISSELL Homecare, Inc. will repair or replace (with new or remanufactured components or
products), at BISSELL’s option, free of charge from the date of purchase by the original
purchaser, for three years any defective or malfunctioning part.
See information below on "If your BISSELL product should require service".
This warranty applies to product used for personal, and not commercial or rental service. This
warranty does not apply to fans or routine maintenance components such as filters, belts, or
brushes. Damage or malfunction caused by negligence, abuse, neglect, unauthorized repair, or any
other use not in accordance with the User's Guide is not covered.
If your BISSELL product should require service:
Contact BISSELL Consumer Services to locate a BISSELL Authorized Service Center in your
area.
If you need information about repairs or replacement parts, or if you have questions about
your warranty, contact BISSELL Consumer Services.
Website or E-mail:
www.bissell.com
Use the “Customer Support” tab.
Or Call:
BISSELL Consumer Services
1-800-237-7691
Monday - Friday 8 a.m. - 10 p.m. ET
Saturday 9 a.m. - 8 p.m. ET
Or Write:
BISSELL Homecare, Inc.
PO Box 3606
Grand Rapids, MI 49501
ATTN: Consumer Services
BISSELL HOMECARE, INC. IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES
OF ANY NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT. BISSELL’S LIABILITY WILL NOT
EXCEED THE PURCHASE PRICE OF THE PRODUCT.
Some states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you.
*EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER ORAL OR
WRITTEN. ANY IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION OF LAW, INCLUDING
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,
ARE LIMITED TO THE THREE YEAR DURATION FROM THE DATE OF PURCHASE AS DESCRIBED
ABOVE.
Some states do not allow limitations on how long an implied warranty last so the above limitation
may not apply to you.
www.bissell.com800.237.7691
19
Don't forget to register your product!
Registering is quick, easy and offers you benefits over the lifetime of your product.
You’ll receive:
BISSELL Rewards Points
Automatically earn points for discounts and free shipping on future purchases.
Faster Service
Supplying your information now saves you time should you need to contact us with
questions regarding your product.
Product Support Reminders and Alerts
We’ll contact you with any important product maintenance reminders and alerts.
Special Promotions
Optional: Register your email to receive notice of offers, contests, cleaning tips and more!
Visit www.bissell.com/registration now!
BISSELL consumer services
For information about repairs or replacement parts, or questions about your warranty, call:
BISSELL Consumer Services
1-800-237-7691
Monday - Friday 8 a.m. — 10 p.m. ET
Saturday 9 a.m. — 8 p.m. ET
Or write:
BISSELL Homecare, Inc.
PO Box 3606
Grand Rapids MI 49501
ATTN: Consumer Services
Or visit the BISSELL website - www.bissell.com
When contacting BISSELL, have model number of cleaner available.
Please record your Model Number: ___________________
Please record your Purchase Date: ___________________
NOTE: Please keep your original sales receipt. It
provides proof of purchase date in the event of a
warranty claim. See Warranty on page 19 for details.
20
©2011 BISSELL Homecare, Inc
Grand Rapids, Michigan
All rights reserved. Printed in China
Part Number 110-4384
Rev 11/11
Visit our website at:
www.bissell.com
www.bissell.com800.237.7691