Bissell 35401 Vacuum Cleaner User Manual

Lift-Off®
B A G L E S S
USER’S GUIDE
3750/6595 SERIES
3
Safety Instructions
4
Product Diagram
4-6
Assembly
6-8
Operations / Special Tools
9-13
14
15
15
16
Maintenance
Troubleshooting
Replacement Parts
Consumer Services
Warranty
Thanks for buying a BISSELL Lift-Off®
We’re glad you purchased a BISSELL Lift-Off Vacuum. Everything
we know about floor care went into the design and construction of this
powerful, high-tech home vacuuming system.
Your BISSELL Lift-Off is well made, and we back it with a limited
comprehensive one-year warranty. We also stand behind it with a
knowledgeable, dedicated Consumer Services department, so, should you
ever have a problem, you’ll receive fast, considerate assistance.
My great-grandfather invented the floor sweeper in 1876. Today, BISSELL is
a global leader in the design, manufacture, and service of high quality
homecare products like your BISSELL Lift-Off.
Thanks again, from all of us at BISSELL.
Mark J. Bissell
President and Chief Executive Officer
IMPORTANT SAFETY INSTRUCTIONS
Keep hair, loose clothing, fingers, and all
parts of body away from openings and
moving parts.
■ Turn off all controls before plugging or
READ ALL INSTRUCTIONS
unplugging vacuum cleaner.
BEFORE USING YOUR
■ Use extra care when cleaning stairs.
UPRIGHT VACUUM.
■ Unplug before attaching the turbo brush.
Always connect to a polarized outlet (left slot is
wider than right). Unplug from outlet when not ■ Do not pick up flammable materials (lighter
fluid, gasoline, kerosene, etc.) or use in the
in use and before conducting maintenance.
presence of explosive liquids or vapors.
■ Do not pick up toxic material (chlorine
To reduce the risk of
bleach, ammonia, drain cleaner, etc.).
fire, electric shock, or injury:
■ Do not use vacuum cleaner in an enclosed
■ Do not modify the polarized plug to fit a
space filled with vapors given off by oil
non-polarized outlet or extension cord.
base paint, paint thinner, some moth
■ Do not leave vacuum cleaner unattended
proofing substances, flammable dust, or
when it is plugged in.
other explosive or toxic vapors.
■ Unplug from outlet when not in use and
■ Do not pick up hard or sharp objects such
before servicing.
as glass, nails, screws, coins, etc.
■ Do not use outdoors or on wet surfaces.
■ Do not pick up anything that is burning or
■ Do not allow children to operate vacuum
smoking, such as cigarettes, matches, or
cleaner or use as a toy.
hot ashes.
■ Close attention is necessary when used by
■ Do not use without filters in place.
or near children.
■ Use only on dry, indoor surfaces.
■ Do not use for any purpose other than
■ Keep appliance on a level surface.
described in this User’s Guide.
WARNING: The Power Cord on this product
■ Use only manufacturer’s recommended
contains lead, a chemical known to the State
attachments.
of California to cause birth defects or other
■ Do not use with damaged cord or plug.
reproductive harm. WASH HANDS AFTER
HANDLING.
■ If appliance is not working as it should,
has been dropped, damaged, left outdoors, SAVE THESE INSTRUCTIONS
or dropped into water, have it repaired at
FOR FUTURE USE.
an authorized service center.
■ Do not pull or carry by cord, use cord as a
handle, close a door on cord, or pull cord
around sharp edges or corners. Do not run THIS APPLIANCE HAS A
appliance over cord. Keep cord away from POLARIZED PLUG.
heated surfaces.
To reduce the risk of electric shock, this
■ Do not unplug by pulling on cord. To
appliance has a polarized plug (one blade is wider
unplug, grasp the plug, not the cord.
than the other). This plug will fit in a polarized
■ Do not handle vacuum cleaner or plug with
outlet only one way. If the plug does not fit fully in
wet hands.
the outlet, reverse the plug. If it still does not fit,
■ Do not put any object into openings. Do
contact a qualified electrician to install a proper
outlet. Do not change the plug in any way.
not use with any opening blocked; keep
openings free of dust, lint, hair, and
This model is for household use only.
anything that may reduce air flow.
When using an electrical appliance,
basic precautions should be observed,
including the following:
■
WARNING:
3
Comfort Grip
Handle
Cord Clip
Dusting Brush/
Upholstery Tool
Hose Clip
Release Button
Stretch Hose
Quick Release
Cord Wrap
Upper
Tank
Knob
Crevice
Tool
Carrying
Handle
Hepa
Media
PostMotor
Filter
Power
Switch
Brush On/Off
Switch
Detachable
Canister
Louvers/Filter Frame
Upper Tank Filter
(Inside Louvers)
Telescoping
Extension Wand
Upper Tank
Hose Grip
Power
Cord
Dirt Container
Pre-Motor Filter
Handle Release Pedal
Hose
Grip Base
Lock ’n
Seal™ Lever
Headlight
Height
Adjustment
Knob
CAUTION:
Do not plug in your vacuum
cleaner until you are familiar
with all instructions and
operating procedures.
Powerfoot
Furniture
Protection
Guard
How To Use This Guide
This User’s Guide has been designed to help you get the
most satisfaction from your BISSELL Lift-Off. You’ll find
assembly and operating instructions, safety precautions, as well
as maintenance and troubleshooting instructions. Please read
this Guide thoroughly before assembling your vacuum cleaner.
Pay particular attention to the product diagram, assembly
instructions, and part names. Locate and organize all parts
before assembly. Familiarize yourself with the parts and where
they fit. Following this User’s Guide will greatly enhance your
ability to get the most performance from your BISSELL Lift-Off
for many years.
How To Put It Together
The only tool you’ll need to assemble your vacuum cleaner
is a screwdriver.
Attach Handle To Vacuum
1.
Locate the vacuum Handle and remove the screw packet
taped to the base of the Handle.
2.
Stand the vacuum upright and slide the base of the Handle
firmly into the grooves at the top of the vacuum body.
3.
Check to be sure the Handle is fitted to the vacuum
body. If there is a gap in front, continue to push firmly
until the Handle is flush.
4.
Insert two of the screws from the screw packet into the
existing holes. Tighten securely with a screwdriver.
Attach Vacuum Hose and Tools
1.
Position the Hose Assembly on the back of the canister
as shown.
2.
Attach the Hose with the remaining two screws from the
packet. Tighten securely with a screwdriver.
WARNING:
Plastic film can be dangerous.
To avoid danger of suffocation,
keep away from babies
and children.
Attach Vacuum Hose and Tools Continued
3.
Slide the end of the Hose Grip onto the Hose Grip Base.
Place the Hose into the Hose Clip.
NOTE: The Powerfoot will not operate effectively
unless the Hose is firmly attached to the base.
4.
Combination
Tool
Snap the Telescoping Extension Wand, Crevice Tool, and
Combination Tool into the storage clips as shown.
Crevice Tool
Telescoping
Wand
How To Use Your BISSELL Lift-Off
Power Cord Quick Release
1.
2.
3.
4.
The Power Cord is stored at the side of the Detachable
Canister, wrapped around two Cord Wraps. A molded clip
on the polarized plug allows it to be fastened to the
Power Cord during storage.
Unclip polarized plug from Power Cord.
CAUTION:
Before using your vacuum, make
sure that the Dirt Container and
Upper Tank are in locked position
and that all filters (Upper Tank,
Pre-Motor and Post-Motor) are in
place. Do not operate your vacuum
without these filters.
Rotate the Upper Cord Wrap toward floor and slip the
Power Cord off.
Quick Release
Cord Wrap
Plug the polarized plug into a polarized outlet.
To keep the Power Cord out of your way while cleaning,
place it in the Cord Clip, located near the top of
the Handle.
Power Switch/Brush Switch
The Power Switch is located just below the handle on the front of
the Detachable Canister. Push the rocker switch “ON” (I) to
vacuum, and “OFF” (O) when cleaning is complete.
The Brush Switch is located just below the handle on the front of
the Detachable Canister next to the Power Switch. This switch
turns the Rotating Brush on and off. The Brush Switch should be
in the “ON” (I) position for normal carpet cleaning. You may want
to turn the Brush Switch “OFF” (O) for bare floor cleaning or other
delicate surfaces.
Note: Your BISSELL Lift Off vacuum is equipped
with a special internal switch that turns the
Rotating Brush off whenever the unit is in the
Upright position.
Handle Positions
1.
2.
Upright – For storage and above floor cleaning with tools.
Normal Cleaning – Press the Handle Release Pedal with
your foot to recline.
Brush
Power
Power Height Adjustment
The Powerfoot on your BISSELL Lift-Off can be adjusted to clean
several floor surfaces.
NOTE: For optimal cleaning performance, adjust to
the lowest practical setting. If your cleaner is
difficult to push, adjust to the next higher setting.
1.
2.
Place Handle in Upright Position.
Tip:
Before cleaning
under low
furniture, check
area first for
objects that
might harm the
unit or block the
Vacuum Hose.
Turn Height Adjustment Knob to desired setting.
Lowest Setting – For bare floors.
Medium Settings – For short and medium pile carpets.
Highest Setting – For plush pile carpet.
NOTE: You may also adjust the setting while in
the Normal Cleaning Position.
Special Tools
Your BISSELL Lift-Off is not only a powerful floor vacuum cleaner,
it’s also a versatile stairs and above floor vacuum when you select
one of the special tools.
Note: The tools can be used with the vacuum in the
Upright Position or with the Detachable Canister.
Detach the Vacuum Hose by grasping the Hose Grip and
lifting to separate from the Hose Grip Base.
1.
2.
Attach tools by firmly pushing onto Vacuum Hose or
Telescoping Extension Wand.
Combination Dusting Brush/Upholstery Tool:
Two types of cleaning tools are included in one attachment: rotate for desired tool.
■ Use Brush side to dust furniture, blinds, books,
lamps, shelves, and baseboards.
■ Use Upholstery side for curtains, draperies, cushions, fabrics.
Crevice Tool:
Use in tight narrow spaces.
Stair Cleaning Tool:
Use for stairs, area rugs, and other small carpeted
areas. This tool can also be used for bare floors.
Telescoping Extension Wand:
Use with desired attachment for a longer reach.
To extend the Wand, twist the collar to “Unlock”
position and push away from you. Twist the collar to
the “Lock” position to lock into place. To retract,
twist to unlock, pull toward you and twist to relock.
All items may not be included with your model. More
tools are available; to order please refer to page 15.
CAUTION:
Always place vacuum cleaner
on floor in its fully Upright
Position and make sure it is
locked into place before
removing Canister or when
using tools. Placing the Lift
Off in its full Upright Position
automatically stops the
rotating brush.
Cleaning With The Detachable Canister
The Detachable Canister feature makes it possible to easily take
the powerful cleaning action of your BISSELL Lift-Off to stairways,
auto interiors, and other hard-to-reach areas of your home.
Before detaching the Canister, your Lift-Off must be in its fully
Upright Position. You do not need to turn off the power first.
Press the Release Button at the top of the Canister
Handle and lift the Canister to remove.
Release
Button
1.
2.
Detach the Vacuum Hose from the Hose Grip Base at the
back of the Canister.
3.
Attach the desired tool(s) to the Hose Grip at the end of
the Vacuum Hose.
4.
When you’re done, remove the tool(s) and reconnect the
Hose to the Hose Grip Base.
5.
Return the Canister to the Powerfoot by aligning the “feet”
on the front with the bumps on the foot of the Upright
Vacuum. Push the Canister toward the vacuum frame until
it “clicks” into place.
NOTICE:
While vacuuming, certain
Power Cord Storage
When you are done using your BISSELL Lift-Off, return it to the
Upright position and store the Power Cord.
Turn vacuum cleaner off (O).
carpets and low humidity
conditions may generate small
static discharges. The discharges
are entirely harmless and are
not associated in any way with
the main power supply.
1.
2.
Unplug Power Cord by grasping the polarized plug (NOT
the cord) and disconnect from outlet.
3.
Loop Power Cord around Cord Wraps on side of
the Canister.
4.
Clip molded plug to Power Cord to secure.
Transporting Cleaner
1.
To move your vacuum cleaner from room to room, put
the Handle in the Upright Position, tilt the cleaner back
on its rear wheels and push forward.
2.
The cleaner can also be moved by using the Carrying
Handle on the Detachable Canister.
CAUTION:
Do not press the Release Button
while using the Carrying Handle to
transport the vacuum cleaner. The
Canister could detach causing
the rest of the vacuum to fall.
Carrying
Handle
How to Maintain Your BISSELL Lift-Off
To maintain maximum cleaning performance, the following
maintenance steps must be performed:
Empty the Dirt Container when the dirt reaches the “Full”
line on the side.
WARNING:
To
reduce the risk of electric
shock, turn Power Switch
OFF and disconnect
polarized plug from
electrical outlet before
performing maintenance or
troubleshooting checks.
1.
2.
Check the Upper Tank and Pre-Motor Filters monthly and
clean and replace as needed.
3.
Replace the HEPA Media Post-Motor Filter every
six months.
NOTE: More frequent filter cleaning may be
necessary if you are vacuuming new carpet, fine
dust, or have allergy concerns.
Follow the instructions on the following pages to
perform these simple maintenance steps.
Tip:
For maximum
cleaning performance,
check and clean or
replace all filters
as suggested.
Empty Dirt Container
The Dirt Container needs to be emptied when the dirt reaches the
“Full” line on the side of the Container.
Unplug cleaner from electrical outlet.
Full Line
1.
2.
3.
4.
5.
Slide the Lock ‘n Seal Lever to the “Unlock” position.
Grasp handle and pull the Dirt Container straight out to
remove from vacuum.
Empty dirt into garbage container.
Put the Dirt Container back in the vacuum and slide the
lever to the “Lock” position.
Note: The Dirt Container may be washed in
warm water with a mild detergent. Make
sure it is completely dry before using again.
Lock Position
Unlock
Position
Cleaning The Upper Tank & Filter
Use only BISSELL Replacement Filters in your BISSELL Lift-Off.
Upper Tank Filter 203-1085
Unplug the cleaner from electrical outlet.
1.
2.
3.
4.
The Upper Tank Filter can be reached by removing the
Dirt Container, reaching underneath the Upper Tank and
turning the rim of the Filter Frame to unlock. Pull straight
down to remove. Brush the dirt off the Louvers and
Upper Tank Filter.
The foam Upper Tank Filter may be removed and hand
washed in cold water with mild detergent. Rinse well
then air dry thoroughly before replacing.
The Upper Tank and Louvers may also be wiped clean
with a damp cloth.
Note: For easier access, the entire Upper Tank
may be removed by turning the knob on the
back of the cleaner to unlock and pulling the
entire tank straight out.
Upper
Tank
Knob
Cleaning The Pre-Motor and Post-Motor Filters
Use only BISSELL Replacement Filters in your BISSELL Lift-Off®.
Pre-Motor Filter 203-1073
HEPA Media Post-Motor Filter #3091
Unplug the cleaner from electrical outlet.
1.
2.
3.
The Pre-Motor Filter protects the motor from dirt particles.
It is located in the slide out tray underneath the Dirt
Container. If the filter becomes dirty, pull out the tray, lift
out the filter and clean. This filter may be hand washed in
cold water with mild detergent. Rinse well and air dry
thoroughly before replacing.
The HEPA Media Post-Motor Filter assists in the filtration
process to return clean air to the room. It is located
behind the door on the back of the cleaner. If the filter
becomes dirty, open the door, remove the filter and
replace. The HEPA Media Filter is not washable.
Pre-Motor Filter
Hepa Media
Post-Motor Filter
WARNING:
Do not operate cleaner
with damp or wet
filters or without all
filters in place.
Check Rotating Brush and Drive Belt
You should check your vacuum cleaner’s Rotating Floor Brush and
Drive Belt regularly for wear or damage. You should also clean the
brush and brush ends of strings, hair, and carpet fibers. These can
wrap around the brush and hamper its ability to effectively clean
your carpet. Also remove any debris that has accumulated under
the brush cover.
Unplug cleaner from electrical outlet.
1.
2.
injury from moving
parts, turn off vacuum
cleaner and disconnect
Power Plug from
electrical outlet.
Remove Detachable Canister from vacuum cleaner.
3.
Recline Handle and turn vacuum cleaner over so bottom
side is up.
4.
Remove the six screws as shown with a Phillips
head screwdriver. Lift the Brush Cover off.
5.
CAUTION:
To reduce the risk of
Grasp Rotating Floor Brush at both ends and lift.
6.
Clean strings, hair and other debris from Rotating Floor
brush, paying particular attention to brush ends.
7.
Clean strings, hair and other debris from Motor Pulley
and Drive Belt areas.
8.
Check Drive Belt carefully for wear, cuts or
stressed areas.
9.
Check Air Passageway for obstructions. Remove debris
from this area.
Motor Pulley
Air Passageway
Replace Drive Belt
Use only BISSELL Style 8 Replacement Belts (#3200) in your BISSELL Lift-Off.
Unplug cleaner from electrical outlet.
1.
2.
With Rotating Floor Brush removed from vacuum cleaner (Steps 1-5
of Check Rotating Floor Brush and Drive Belt), grasp old Drive Belt
and remove from Motor Pulley. Discard old Drive Belt.
3.
Place new Drive Belt over Motor Pulley and stretch other end over
Rotating Floor Brush in the space between the bristles.
4.
5.
6.
Place ends of Rotating Floor Brush down into slots on sides as shown.
Turn Rotating Floor Brush by hand several times in the direction of
Motor Pulley. If properly installed, Drive Belt will center itself on
Rotating Brush crown.
Reposition Brush Cover and screws. Tighten screws securely.
Replace Light Bulb
Use only BISSELL Replacement Bulb (#203-1007) in your BISSELL Lift-Off.
Unplug cleaner from electrical outlet.
1.
2.
3.
4.
5.
Remove Detachable Canister and recline Handle of vacuum.
Using a screwdriver, remove the one screw as shown and lift off the lens.
Remove the bulb from the socket by pushing in gently and turning it
towards brush. Install the new bulb by pushing it gently into the
socket and turning away from brush.
Reposition lens and secure with the one screw.
Clearing Clogs
Low suction or poor pickup may be due to a clog in the vacuum cleaner. If
you notice a change in the sound of the motor or a reduction in the spinning
action, check for clogs.
Unplug cleaner from electrical outlet.
1.
2.
Empty Dirt Container.
3.
Check Upper Tank for build up or clogs.
4.
Suction
Inlet
Remove the Upper Tank and check the suction inlet for a clog.
5.
Check the clear panel on the back of the Canister for a clog. If there
is an obstruction, remove the screws to remove the panel and clear
this area.
6.
Grasp the Hose Grip and lift to separate from the suction opening.
Check for a clog in the Base or the Hose.
7.
If the clog persists, follow the instructions for Checking the Rotating
Brush on page 1x1 and inspect the Air Passageway for obstructions.
Clear
Panel
Suction
Opening
Air Passageway
Thermal Protector
An internal thermal protector has been designed into your cleaner to protect
it from overheating. When the thermal protector activates, the main
vacuum motor will stop operating. If this happens, proceed as follows:
1.
2.
3.
4.
Turn the cleaner OFF (O) and unplug from electrical outlet.
Check the Upper Tank area, Pre-Motor Filter and
Post-Motor Filter for dirt accumulation.
Refer to the "Clearing Clogs" section.
When the motor cools for approximately 30 minutes, the
thermal protector automatically resets and cleaning may continue. If
the thermal protector continues to activate after following the above
steps, your cleaner may need servicing. Call BISSELL Consumer
Services, or visit the website.
Note: The thermal protector controls the main vacuum
motor only, not the brush motor. If the thermal protector
activates, the brush will continue to operate normally;
however, there will be no suction.
CAUTION:
To reduce the risk of
injury from moving
parts, turn off vacuum
cleaner and disconnect
Power Plug from
electrical outlet.
Troubleshooting
Vacuum cleaner won't run.
Possible Causes
1
2
3
Remedies
Power cord not firmly plugged in
Blown household fuse or breaker
Thermal protector activated
1
2
3
Check electrical plug
Check/replace fuse - Reset breaker
Allow cleaner to cool for 30 minutes, see pg. 13
No Power at Rotating Floor Brush.
Possible Causes
Remedies
1
Canister is not securely seated
1
2
Brush Switch turned to “Off”
2
Remove Canister and replace, making sure that
it “clicks” into place
Make sure Brush Switch is in “On” position
Vacuum cleaner or Tools won't pick up dirt.
Possible Causes
1
2
3
4
5
6
7
8
9
10
Remedies
Incorrect Height Adjustment
Hose not attached to suction opening
Crack or hole in Hose
Drive Belt broken, worn or off motor pulley
Rotating Floor Brush bristles worn
Rotating Floor Brush jammed
Clog in vacuum
Dirt Container full
Dirt Container or Upper Tank not installed properly
Filters are dirty
1
2
3
4
5
6
7
8
9
10
Adjust Powerfoot to correct height setting
Grasp Hose Grip and firmly push onto the base
Check Hose and replace if needed
Reposition or replace Drive Belt, see pg. 11-12
Replace brush
Remove brush and clean debris from brush ends
Follow instructions on pg. 13 for clearing clogs
Empty Dirt Container
Position correctly and lock in place
Check and clean Upper Tank, Pre-Motor and
Post-Motor Filters
Vacuum cleaner is difficult to push.
Possible Causes
1
Remedies
Incorrect Height Adjustment
1
Adjust Powerfoot to correct height setting
Visible dirt escaping from cleaner.
Possible Causes
Remedies
2
Dirt Container full
Filters missing or installed incorrectly
2
3
Dirt Container installed incorrectly
3
WARNING:
To reduce the risk of injury
from moving parts and/ or
electrical shock, turn Power
Switch OFF and disconnect
polarized plug from electrical
outlet before performing
troubleshooting checks.
1
Empty Dirt Container
Check Upper Tank, Pre-Motor and Post-Motor
Filters for correct installation
Pull out and re-insert Dirt Container correctly
If suggested solutions do not correct the problem, call:
BISSELL Consumer Services
1-800-237-7691
Monday - Friday 8 a.m. — 10 p.m. ET
Saturday
9 a.m. — 8 p.m. ET
or visit the BISSELL website - www.bissell.com
Replacement Parts – BISSELL Lift-Off Series
You may purchase replacement parts from your retailer, by calling BISSELL
Consumer Services or by visiting our website. To locate a retailer near
you, or to place an order using Visa, MasterCard, Discover or American
Express, call
1
2
3
4
5
6
7
8
10
11
BISSELL Consumer Services
1-800-237-7691
Monday - Friday
8 a.m. — 10 p.m. ET
Saturday
9 a.m. — 8 p.m. ET
Or visit our Website - www.bissell.com
Item
Part No.
1
2
3
4
5*
6
7
8
9
10
11
3200
Style 8 Drive Belt (2-Pack)
203-1007
Headlight Bulb
203-1063
Crevice Tool
203-1099
Dusting Brush/Upholstery Tool
203-6624
Stair Cleaning Tool
203-6625
Telescoping Extension Wand
203-6633
Vacuum Hose
203-6619
Brush Roll
203-1085
Upper Tank Filter
203-1073
Pre-Motor Filter
3091
HEPA Media Post-Motor Filter
*May not be included with every model.
Part Name
9
BISSELL Consumer Services
For information about repairs or replacement parts, or
questions about your warranty, call:
BISSELL Consumer Services
1-800-237-7691
Monday - Friday
Saturday
8 a.m. — 10 p.m. ET
9 a.m. — 8 p.m. ET
Or write:
BISSELL Homecare, Inc.
PO Box 3606
Grand Rapids, MI 49501
ATTN: Consumer Services
Or visit the BISSELL website - www.bissell.com
When contacting BISSELL, have model number of unit available.
Please record your Model Number: ___________________
Please record your Purchase Date: ___________________
NOTE: Please keep your original sales receipt. It is your warranty.
1
Warranty
This warranty gives you specific legal rights, and you may also have other rights which may vary from state to
state. If you need additional instruction regarding this warranty or have questions regarding what it may cover, please
contact BISSELL Consumer Services by E-mail, telephone, or regular mail as described below.
Limited One Year Warranty
Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, upon receipt of the product BISSELL Homecare,
Inc. will repair or replace (with new or remanufactured components or products), at BISSELL’s option, free of charge
from the date of purchase by the original purchaser, for one year any defective or malfunctioning part.
See information below on "If your BISSELL product should require service".
This warranty applies to product used for personal, and not commercial or rental service. This warranty does not
apply to fans or routine maintenance components such as filters, belts, or brushes. Damage or malfunction caused
by negligence, abuse, neglect, unauthorized repair, or any other use not in accordance with the User's Guide is not
covered.
If your BISSELL product should require service:
Contact BISSELL Consumer Services to locate a BISSELL Authorized Service Center in your area.
If you need information about repairs or replacement parts, or if you have questions about your warranty, contact
BISSELL Consumer Services.
Website or E-mail:
www.bissell.com
Use the “Customer Services” tab.
Or Call:
BISSELL Consumer Services
1-800-237-7691
Monday - Friday 8 a.m. - 10 p.m. ET
Saturday 9 a.m. - 8 p.m. ET
Or write:
BISSELL Homecare, Inc.
PO Box 3606
Grand Rapids MI 49501
ATTN: Consumer Services
BISSELL HOMECARE, INC. IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY
NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT. BISSELL’S LIABILITY WILL NOT EXCEED THE
PURCHASE PRICE OF THE PRODUCT.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation
or exclusion may not apply to you.
*EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER
ORAL OR WRITTEN. ANY IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION
OF LAW, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE ONE YEAR
DURATION FROM THE DATE OF PURCHASE AS DESCRIBED ABOVE.
Some states do not allow limitations on how long an implied warranty lasts, so
the above limitation may not apply to you.
16
©2003 BISSELL Homecare, Inc
Grand Rapids, Michigan
All rights reserved. Printed in Korea.
Part Number 010-5519
Rev 7/03
Visit our website at:
www.bissell.com