Bissell 3594 Vacuum Cleaner User Manual

CleanView®
B A G L E S S
Power Trak®
USER’S GUIDE
3593/3594/6590 SERIES
3
Safety Instructions
4
Product View
5-6 Assembly Instructions
6-9 Operation / Special Tools
10-13 Maintenance
13
14
15
16
Warranty
Consumer Services
Troubleshooting
Replacement Parts
Thanks For Buying A BISSELL CleanView®
We’re glad you purchased a BISSELL CleanView Vacuum. Everything we know
about floor care went into the design and construction of this complete,
high-tech home vacuuming system.
Your BISSELL CleanView is well made, and we back it with a limited
comprehensive one-year warranty. We also stand behind it with a
knowledgeable, dedicated Consumer Services Department, so, should you
ever have a problem, you’ll receive fast, considerate assistance.
My great-grandfather invented the floor sweeper in 1876. Today,
BISSELL is a global leader in the design, manufacture, and service of high
quality homecare products like your BISSELL CleanView.
Thanks again, from all of us at BISSELL.
Mark J. Bissell
President and Chief Executive Officer
2
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic
precautions should be observed, including
the following:
READ ALL INSTRUCTIONS
BEFORE USING YOUR
UPRIGHT VACUUM.
Always connect to a polarized outlet (left slot is
wider than right). Unplug from outlet when not in
use and before conducting maintenance.
WARNING:
To reduce
the risk of fire, electric shock,
or injury:
■ Do not modify the polarized plug to fit a
non-polarized outlet or extension cord.
■ Do not leave vacuum cleaner unattended
when it is plugged in.
■ Unplug from outlet when not in use and
before servicing.
■ Unplug before attaching TurboBrush.
■ Do not use outdoors or on wet surfaces.
■ Do not allow children to operate vacuum
cleaner or use as a toy.
■ Close attention is necessary when used by or
near children.
■ Do not use for any purpose other than described
in this User’s Guide.
■ Use only manufacturer’s recommended
■
■
■
■
■
■
attachments.
Do not use with damaged cord or plug.
If appliance is not working as it should,
has been dropped, damaged, left outdoors, or
dropped into water, have it repaired at an
authorized service center.
Do not pull or carry by cord, use cord as a
handle, close a door on cord, or pull cord
around sharp edges or corners. Do not run
appliance over cord. Keep cord away from
heated surfaces.
Do not unplug by pulling on cord. To unplug,
grasp the plug, not the cord.
Do not handle vacuum cleaner or plug with
wet hands.
Do not put any object into openings.
Do not use with any opening blocked; keep
openings free of dust, lint, hair, and anything
that may reduce air flow.
■ Keep hair, loose clothing, fingers, and all parts
of body away from openings and moving parts.
■ Turn off all controls before plugging or
unplugging vacuum cleaner.
■ Use extra care when cleaning stairs.
■ Do not pick up flammable materials (lighter
fluid, gasoline, kerosene, etc.) or use in the
presence of explosive liquids or vapors.
■ Do not pick up toxic material (chlorine bleach,
ammonia, drain cleaner, etc.).
■ Do not use vacuum cleaner in an enclosed
space filled with vapors given off by oil base
paint, paint thinner, some moth proofing
substances, flammable dust, or other
explosive or toxic vapors.
■ Do not pick up hard or sharp objects such as
glass, nails, screws, coins, etc.
■ Do not pick up anything that is burning
or smoking, such as cigarettes, matches, or
hot ashes.
■ Do not use without filters in place.
■ Use only on dry, indoor surfaces.
■ Keep appliance on a level surface.
■ Do not carry the vacuum cleaner while it
is running.
WARNING: The Power Cord on this product
contains lead, a chemical known to the State of
California to cause birth defects or other
reproductive harm. WASH HANDS
AFTER HANDLING.
SAVE THESE
INSTRUCTIONS FOR
FUTURE USE
THIS APPLIANCE HAS
A POLARIZED PLUG.
To reduce the risk of electric shock, this appliance has
a polarized plug (one blade is wider than the other).
This plug will fit in a polarized outlet only one way. If
the plug does not fit fully in the outlet, reverse the
plug. If it still does not fit, contact a qualified electrician
to install a proper outlet. Do not change the plug in
any way.
This model is for household use only.
3
Handle
Cord Clip
Hose Clip
Stretch Hose
Carrying
Handle
TurboBrush®
(Select Models Only)
Quick Release™
Cord Wrap
Power Cord
Crevice Tool
Quick Reach®
Handle
Upper Tank Knob
Extension Wand
Hose Wand
Dusting Brush/
Upholstery Tool
Hose
Wand Base
Clean Carpet Sensor
(Select Models Only)
Power Switch
Clean Filter Indicator
(Select Models Only)
Louvers
Upper Tank
Frame and Filter
(Inside Louvers)
Upper Tank
Post-Motor
Filter
Handle Release
Pedal
Dirt Container
Pre-Motor Filter
Headlight
Optional Hepa
Media Filter
(Select Models
Only)
Lock ’n Seal™
Lever
Height
Adjustment
Knob
Power Trak®
Window
Furniture Protection
Guard
CAUTION:
4
Do not plug in your vacuum
cleaner until you are familiar
with all instructions and
operating procedures.
How To Use This Guide
This User’s Guide has been designed to help you
get the most satisfaction from your BISSELL CleanView.
You’ll find assembly and operating instructions,
safety precautions, as well as maintenance and
troubleshooting instructions. Please read this Guide
thoroughly before assembling your vacuum cleaner.
Pay particular attention to the product diagram,
assembly instructions, and part names. Locate and
organize all parts before assembly. Familiarize
yourself with the parts and where they fit. Following
this User’s Guide will greatly enhance your ability to
get the most performance from your BISSELL
CleanView for many years.
WARNING:
Plastic film can be
dangerous. To avoid
danger of suffocation,
keep away from
babies and children.
How To Put It Together
The only tool you’ll need to assemble your vacuum
cleaner is a screwdriver.
Attach Handle To Vacuum
1. Locate the vacuum Handle and remove the screw
packet taped to the base of the Handle.
2. Stand the vacuum upright and slide the base of
the Handle firmly into the grooves at the top of the
vacuum body.
3. Check to be sure the Handle is fitted to the vacuum
body. If there is a gap in front, continue to push firmly
until the Handle is flush.
4. Insert the screw provided from the screw packet into the
existing hole. Tighten securely with a screwdriver.
5
Attach Vacuum Hose and Tools
1. Position the Hose Assembly on the back of the
vacuum as shown.
2. Attach the Hose with the remaining two screws from
the packet. Tighten securely with a screwdriver.
For Models with the Twist ‘n Snap™ Hose
1a Position the Twist ‘n Snap Hose assembly on the
back of the vacuum.
2a Line up the tabs on the base of the Twist ‘n Snap
Hose with the corresponding notches on the hose
collar as shown.
3a Turn the Twist ‘n Snap Hose to the right to lock
the hose into place.
3. Grasping the Quick Reach Handle, slide the end of
the Hose Wand onto the Hose Wand Base. Snap the
Hose into the Hose Clip.
NOTE: The Powerfoot will not operate
effectively unless the Hose Wand is
firmly attached.
Twist ‘n Snap Hose Models
4. Slide the Extension Wand and the Crevice Tool
together into the storage clip as shown.
5. Slide the Dusting Brush/Upholstery Tool into the storage clip
as shown.
6. Attach the TurboBrush by aligning the small holes near the
brush roll with the tabs at the bottom of TurboBrush housing. Snap TurboBrush into place as shown.
Select Models Only
NOTICE:
The Floor Brush will continue to rotate
while you use your vacuum for above
floor cleaning. To prevent carpet
damage, do not lean on the vacuum or
let the Powerfoot tilt forward.
CAUTION:
Before using your vacuum,
make sure that the Dirt
Container and Upper Tank are
in locked position and that all
filters (UpperTank, Pre-Motor
and Post-Motor) are in place.
Do not operate your vacuum
without these filters.
6
How To Use Your Vacuum
Handle Positions
1
Press the Handle Release Pedal with your foot to place
your vacuum into one of three cleaning positions.
2
1. Upright- For storage and above floor cleaning with tools.
2. Normal Cleaning- Press Handle Release Pedal once. Use
for most household floor cleaning tasks.
3
3. Low Cleaning- With the vacuum in normal cleaning
position, press Handle Release Pedal again. Use for
reaching under low furniture such as tables, chairs
or beds.
Height Adjustment
The Powerfoot/Rotating Floor Brush on your
vacuum can be adjusted to clean several
floor surfaces.
NOTE: For optimal cleaning performance,
adjust to the lowest practical setting. If your
cleaner is difficult to push, adjust to the next
higher setting.
1. Place Handle in Upright Position.
2. Turn Height Adjustment knob to desired setting.
Lowest Setting For bare floors.
Medium Settings For short and medium
pile carpets.
Highest Setting For plush pile carpet.
Tip:
Tip:
Before cleaning under
low furniture, check
area first for objects
that might harm the
unit or block the
Vacuum Hose.
Your vacuum features
a Quick-Release
Cord Wrap. To
remove the Power
Cord quickly and
easily, rotate the
Upper Cord Wrap
towards floor, and slip
Power Cord from
Upper and Lower
Cord Wraps.
3. Place the Handle in the normal cleaning position and the
Powerfoot will adjust to the setting chosen.
NOTE: You may also adjust the setting while
in the normal cleaning position.
Transporting Cleaner
1. To move your cleaner from room to room, put the Handle
in the upright position, tilt the cleaner back on its rear
wheels and push forward.
Carrying
Handle
2. The cleaner can also be moved by using the
Carrying Handle.
7
Clean Carpet Sensor
Select models only
The Clean Carpet Sensor detects dirt being picked up
while the vacuum is in use.When the vacuum is picking
up dirt, the red light will come on. Occasionally, the lights
may alternate quickly back and forth if the area is only
lightly soiled or the dirt is spread out. For the best
cleaning, continue to vacuum until the green light
remains constantly illuminated.
Clean Filter Indicator
Select Models Only
The Clean Filter Indicator tells you when airflow in
the vacuum is reduced due to dirty filters or a clog
in the hose. The Clean Filter Indicator will remain
green until the airflow is reduced. At that time, it
begins to change to red. When it is fully red, the airflow is significantly reduced or blocked. Follow the
steps on page 11 to clean your filters. All filters in
the vacuum should be cleaned or replaced when the
Clean Filter Indicator turns red.
If the indicator remains red after all filters have been
cleaned, follow the steps on pages 12-13 to check
for and clear clogs.
NOTICE:
While vacuuming, certain carpets
and low humidity conditions may
generate small static discharges.
The discharges are entirely
harmless and are not associated
in any way with the main
power supply.
8
Special On-Board Tools
Your vacuum is not only a powerful carpet and rug
vacuum cleaner, it’s also a versatile above floor vacuum cleaner when you select one of the
special tools.
1. Raise Handle to Upright Position.
2. Grasp the Quick Reach Handle and lift Hose Wand to
separate from suction intake opening.
3. Attach tools by firmly pushing onto Vacuum Hose or
Extension Wand.
Dusting Brush Tool (Select Models): Use to dust
furniture, blinds, books, lamps, shelves,
draperies, and cushions.
Dusting Brush/Upholstery Tool (Select Models): Two
types of cleaning tools in one attachment.
•Use the Dusting Brush to dust furniture, blinds, books,
lamps, shelves and baseboards.
•Slide the brush off to use the Upholstery Tool on
cushions, draperies and fabrics.
Crevice Tool: Use in tight narrow spaces.
Extension Wand: Use with desired attachment for a
longer reach.
TurboBrush (Select Models): Use rotating brush action
for small areas such as stairs and upholstery.
Note: Press gently when using the
TurboBrush to gain maximum cleaning. Too
much pressure will cause the brush to
stop rotating.
Power Cord Storage
When you are done using your vacuum, return it to
the Upright position and store the Power Cord.
Tip:
Hair, string and small objects can block
the Vacuum Hose or Tools. Check them
occasionally for obstructions.
NOTICE:
The Floor Brush will continue
to rotate while you use your
vacuum for above floor cleaning.
To prevent carpet damage, do not
lean on the vacuum or let the
Powerfoot tilt forward.
1. Turn vacuum cleaner off.
2. Unplug Power Cord by grasping the polarized plug (NOT
the cord) and disconnect from outlet.
3. Loop Power Cord around Cord Wraps on side of
vacuum cleaner.
4. Clip molded plug to Power Cord to secure.
CAUTION:
The Rotating Floor Brush
continues to rotate while tools
are in use. To reduce the risk of
injury from moving parts,
always move the cleaner with
the Carrying Handle at the back
of the cleaner. Always place
vacuum cleaner on floor with
Handle in Upright position when
using tools. Never place your
fingers under the cleaner when
it is running. Never place
Powerfoot on furniture or
uneven surfaces. Do not place
vacuum cleaner close enough
to objects to pull them into
rotating brush.
9
How To Maintain Your Vacuum
To maximize your cleaning performance and extend the
life of your vacuum, it is very important that you empty
your dirt container and check and clean your filters frequently. Perform the following maintenance steps:
1. Empty the Dirt Container when the dirt reaches the “Full”
line on the side.
2. Check the Upper Tank and Pre-Motor Filters at least once a
WARNING:
To reduce the risk of
electric shock, turn
Power Switch OFF and
disconnect polarized
plug from electrical outlet
before performing
maintenance or
troubleshooting checks.
month and clean or replace as needed.
3. Clean or replace the Post-Motor Filter every three to six months.
Note: More frequent filter cleaning may be
necessary if you are vacuuming new carpet,
fine dust, or have allergy concerns. Follow the
instructions on the following pages to perform
these simple maintenance steps.
For maximum cleaning
performance, check
and clean or replace
all filters as suggested.
Empty Dirt Container
Full Line
The Dirt Container needs to be emptied when the dirt
Unlock
reaches the “Full” line on the side of the Container.
1. Unplug cleaner from electrical outlet.
Position
2. Slide the Lock ‘n Seal Lever to the "Unlock" position.
3. Grasp handle and pull the Dirt Container straight out to
remove from vacuum.
4. Empty dirt into garbage container.
5. Put the Dirt Container back in the vacuum and slide the
lever to the "Lock" position.
Note: The Dirt Container may be washed in
warm water with a mild detergent. Make sure it
is completely dry before using again.
Clean Carpet Sensor
To maintain the effectiveness of the Clean Carpet
Sensor, a quarterly cleaning of the internal sensor
lens is recommended. To clean the sensor lens,
detach the Twist ‘n Snap Hose and gently wipe the
clear lens area using a lightly dampened soft cloth.
Allow enough time for the lens to dry thoroughly
before reattaching the Twist ‘n Snap Hose and using
the vacuum.
10
Tip:
Lock Position
Cleaning The Upper Tank & Filter
1. Unplug the cleaner from electrical outlet.
2. The Upper Tank Filter can be reached by removing the Dirt
Container, reaching underneath the Upper Tank and turning
the rim of the Filter Frame to unlock. Pull straight down to
remove. Brush the dirt off the Louvers and Upper Tank Filter.
3. The foam Upper Tank Filter may be removed and hand
washed in cold water with mild detergent. Rinse well then
air dry thoroughly before replacing.
4. The Upper Tank and Louvers may also be wiped clean with
a damp cloth.
Note: For easier access, the entire Upper Tank
may be removed by turning the knob on the
back of the cleaner to unlock and pulling the
entire tank straight out.
Cleaning The Pre-Motor and Post-Motor Filter
1. Unplug the cleaner from electrical outlet.
WARNING:
Do Not operate cleaner
with damp or wet
filters or without all
filters in place.
2. The Pre-Motor Filter protects the motor from dirt particles.
It is located in the slide out tray underneath the Dirt
Container. If the filter becomes dirty, pull out the tray, lift
out the filter and clean.
3. The Post-Motor Filter assists in the filtration process to
return clean air to the room. It is located behind the door on
the side of the cleaner. If the filter becomes dirty, open the
door, remove the filter and clean.
Note: Select Models come with a white, pleated
HEPA Media Filter. This filter is not washable
and must be replaced.
Pre-Motor
Filter
4. The standard filters may be hand washed in cold water
with mild detergent. Rinse well and air dry thoroughly
before replacing.
Check Rotating Floor Brush and Drive Belt
You should check your vacuum cleaner’s Rotating
Floor Brush and Drive Belt regularly for wear or
damage. You should also clean the brush and brush
ends of strings, hair, and carpet fibers. These can
wrap around the brush and hamper its ability to
effectively clean your carpet. Also remove any debris
that has accumulated under the brush cover.
Post-Motor
Filter
WARNING:
To reduce the risk of injury
from moving parts, turn
off vacuum cleaner and
disconnect Power Plug
from electrical outlet.
1. Unplug cleaner from electrical outlet.
2. Place handle in Low position and turn vacuum cleaner over
so bottom side is up.
3. Remove the five screws as shown with a Phillips head
screwdriver. Lift the Brush Cover off.
11
Check Rotating Floor Brush and Drive Belt Continued
4. Grasp Rotating Floor Brush at both ends and lift.
5. Clean strings, hair and other debris from Rotating Floor
Motor Pulley
Brush, paying particular attention to brush ends.
6. Clean strings, hair and other debris from Motor Pulley and
Drive Belt areas.
7. Check Drive Belt carefully for wear, cuts or stressed areas.
8. Check Air Passageway for obstructions. Remove debris
from this area.
Replace Drive Belt
1. Unplug cleaner from electrical outlet.
2. With Rotating Floor Brush removed from vacuum cleaner
(Steps 1-4 of check Rotating Floor Brush and Drive Belt),
grasp old Drive Belt and remove from Motor Pulley.
Discard old Drive Belt.
3. Place new Drive Belt over Motor Pulley and stretch other end
over Rotating Floor Brush in the space between the bristles.
4. Place ends of Rotating Floor Brush down into slots on
sides as shown.
5. Turn Rotating Floor Brush by hand several times in the
direction of Motor Pulley. If properly installed, Drive Belt
will center itself on Rotating Brush crown.
6. Reposition Brush Cover and screws. Tighten screws securely.
Replace Lightbulb
1. Unplug cleaner from electrical outlet
2. Using a screwdriver, remove the two screws as shown
and lift off the lens.
3. Remove the bulb from the socket by pushing in gently
and turning it counterclockwise. Install the new bulb by
pushing it gently into the socket and turning clockwise.
4. Reposition lens and secure with the two screws.
Maintaining Optional TurboBrush
Select Models Only
If a clog is present, unscrew the two screws in the back of
the TurboBrush to remove the faceplate and clear any
obstructions.
12
Air Passageway
Clearing Clogs
Low suction or poor pickup may be due to a clog in
the vacuum cleaner. If you notice a change in the
sound of the motor or a reduction in the spinning
action, check for clogs.
1. Unplug cleaner from electrical outlet.
2. Empty Dirt Container.
Suction
Inlet
3. Check Upper Tank for build up or clogs.
4. Remove the Upper Tank and check the suction inlet for a clog.
5. Grasp the Quick Reach Handle and lift Hose Wand to separate
from the suction opening. Check for a clog in the Base, the
Wand or the Hose.
For Models with the Twist ‘n Snap Hose
Release the hose from the vacuum by turning to
the left. Straighten the hose and unclog with a long,
narrow object.
Remove
the screw attaching the Hose Wand Base to the
6.
vacuum. Straighten the Hose Wand Base and unclog with
long, narrow object.
7. If the clog persists, follow the instructions for Checking
the Rotating Floor Brush on page 12 and inspect the Air
Passageway for obstructions.
Hose Wand
Base
Air Passageway
BISSELL Consumer Services
For information about repairs or replacement
parts, or questions about your warranty, call:
BISSELL Consumer Services
1-800-237-7691
Monday - Friday
Saturday
8 a.m. — 10 p.m. ET
9 a.m. — 8 p.m. ET
Or write:
BISSELL Homecare, Inc.
PO Box 3606
Grand Rapids, MI 49501
ATTN: Consumer Services
Or visit the BISSELL website - www.bissell.com
When contacting BISSELL, have model number of unit available.
Please record your Model Number: ___________________
Please record your Purchase Date: ___________________
NOTE: Please keep your original sales receipt. It is your warranty.
13
WARNING:
To reduce the risk of injury from moving
Troubleshooting
parts and/ or electrical shock, turn Power
Switch OFF and disconnect polarized plug
from electrical outlet before performing
troubleshooting checks.
Vacuum cleaner won’t run
Possible Causes
1
2
Power cord not plugged in
Blown fuse/tripped breaker
Remedies
1
2
Check electrical plug
Check/Replace fuse or reset breaker
Vacuum cleaner or Tools won’t pick up dirt
Possible Causes
1
2
3
4
5
6
7
8
9
10
11
Incorrect Height Adjustment
Hose not attached to suction opening
Twist ‘n Snap Hose not securely attached
Crack or hole in Hose
Broken or worn Drive Belt
Rotating Floor Brush bristles worn
Rotating Floor Brush jammed
Clog in vacuum
Dirt Container full
Dirt Container or Upper Tank not installed properly
Filters are dirty
Remedies
Adjust Powerfoot to correct height
Firmly push Hose Wand into the suction opening
3 Make sure Twist ‘n Snap Hose is snapped into
locked position
4 Check Hose and replace if needed
5 Replace Drive Belt, see page 12
6 Replace brush
7 Remove brush and clean debris from brush ends
8 Clear clog, see pages 12-13
9 Empty Dirt Container
10 Position correctly and lock in place
11 Check and clean Upper Tank,
Pre-Motor and Post-Motor Filters
1
2
Vacuum cleaner is difficult to push
Possible Causes
1
Incorrect Height Adjustment
Remedies
1
Adjust Powerfoot to correct height setting
Visible dirt escaping from cleaner
Possible Causes
Remedies
2
Dirt Container full
Filters missing or installed incorrectly
2
3
Dirt Container installed incorrectly
3
1
1
Empty Dirt Container
Check Upper Tank, Pre-Motor and Post-Motor
Filters for correct installation
Pull out and re-insert Dirt Container correctly
Clean Carpet Sensor not functioning properly
Possible Causes
1
2
14
Clean Carpet Sensor Lens is Dirty
Clog in Suction Intake Area
Remedies
1
2
Clean Internal Sensor Lens, see page 10
Clear clog, see pages 12-13
Replacement Parts – BISSELL Power Trak Series
You may purchase replacement parts from your retailer, by calling BISSELL Consumer
Services or by visiting our website. To locate a retailer near you, or to place an order using
Visa, MasterCard, Discover or American Express, call
BISSELL Consumer Services
1-800-237-7691
Or visit our Website - www.bissell.com
Item Part No.
Part Name
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
32074
203-1007
203-1063
203-1083
203-1228
203-1227
203-1084
203-1164
203-1036
203-2012
203-1055
203-2035
203-1128
203-2013
3093
3099
32076
Style 7/9/10 Drive Belt (2-Pack)
Headlight Bulb
Crevice Tool
Dusting Brush
Dusting Brush/Upholstery Tool (Select Models Only)
TurboBrush (Select Models Only)
Extension Wand
Vacuum Hose
Wire Reinforced Vacuum Hose Gray
Wire Reinforced Vacuum Hose Clear
Wire Reinforced Twist ‘n Snap Vacuum Hose Gray
Wire Reinforced Twist ‘n Snap Vacuum Hose Clear
Hose Collar with Screws (Twist ‘n Snap Hose Only)
Power Trak Brush Roll
Style 7/8 Upper Tank Filter and Pre-Motor Filter Set
Style 7 Post-Motor Filter Set (2 pack)
Style 7 HEPA Media Post-Motor Filter (Select Models Only)
1
2
3
4
5
6
7
8/9/10
11/12
13
14
15
16
17
15
Warranty
This warranty gives you specific legal rights, and you may also have other rights which may vary from state to
state. If you need additional instruction regarding this warranty or have questions regarding what it may cover,
please contact BISSELL Consumer Services by E-mail, telephone, or regular mail as described below.
Limited One Year Warranty
Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, upon receipt of the product BISSELL Homecare,
Inc. will repair or replace (with new or remanufactured components or products), at BISSELL’s option, free of
charge from the date of purchase by the original purchaser, for one year any defective or malfunctioning part.
See information below on "If your BISSELL product should require service".
This warranty applies to product used for personal, and not commercial or rental service. This warranty does not
apply to fans or routine maintenance components such as filters, belts, or brushes. Damage or malfunction caused
by negligence, abuse, neglect, unauthorized repair, or any other use not in accordance with the User's Guide is
not covered.
If your BISSELL product should require service:
Contact BISSELL Consumer Services to locate a BISSELL Authorized Service Center in your area.
If you need information about repairs or replacement parts, or if you have questions about your
warranty, contact BISSELL Consumer Services.
Website or E-mail:
www.bissell.com
Use the “Customer Services” tab.
Or Call:
BISSELL Consumer Services
1-800-237-7691
Monday - Friday 8 a.m. - 10 p.m. ET
Saturday 9 a.m. - 8 p.m. ET
Or write:
BISSELL Homecare, Inc.
PO Box 3606
Grand Rapids MI 49501
ATTN: Consumer Services
BISSELL HOMECARE, INC. IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY
NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT. BISSELL’S LIABILITY WILL NOT EXCEED THE
PURCHASE PRICE OF THE PRODUCT.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or
exclusion may not apply to you.
*EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER
ORAL OR WRITTEN. ANY IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION
OF LAW, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE ONE YEAR DURATION
FROM THE DATE OF PURCHASE AS DESCRIBED ABOVE.
Some states do not allow limitations on how long an implied warranty lasts,
so the above limitation may not apply to you.
16
©2004 BISSELL Homecare, Inc
Grand Rapids, Michigan
All rights reserved. Printed in Korea
Part Number 603-2564
Rev 02/04
Visit our website at:
www.bissell.com