User`s guide | Bissell 44M3 Vacuum Cleaner User Manual

B A G L E S S
USER’S GUIDE
6579 SERIES
3
Safety Instructions
4
Product View
5-6 Assembly Instructions
6-8 Operation / Special Tools
8-11 Maintenance
12-13 Troubleshooting
14
15
16
Warranty
Replacement Parts
Consumer Services
Thanks For Buying A BISSELL Bagless Vacuum
We’re glad you purchased a BISSELL Bagless Vacuum. Everything we know about
floor care went into the design and construction of this complete, high-tech home
vacuuming system.
Your BISSELL Bagless is well made, and we back it with a limited comprehensive
one-year warranty. We also stand behind it with a knowledgeable, dedicated
Consumer Services Department, so, should you ever have a problem, you’ll receive
fast, considerate assistance.
My great-grandfather invented the floor sweeper in 1876. Today, BISSELL is a global
leader in the design, manufacture, and service of high quality homecare products like
your BISSELL Bagless.
Thanks again, from all of us at BISSELL.
Mark J. Bissell
President and Chief Executive Officer
2
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic
precautions should be observed, including
the following:
READ ALL INSTRUCTIONS
BEFORE USING YOUR
UPRIGHT VACUUM.
Always connect to a polarized outlet (left slot is
wider than right). Unplug from outlet when not in
use and before conducting maintenance.
WARNING:
To reduce
the risk of fire, electric shock,
or injury:
unplugging vacuum cleaner.
■ Use extra care when cleaning stairs.
■ Unplug before attaching the turbobrush.
■ Do not pick up flammable materials (lighter
■
■
■
■
■ Do not modify the polarized plug to fit a
non-polarized outlet or extension cord.
■ Do not leave vacuum cleaner unattended
when it is plugged in.
■ Unplug from outlet when not in use and
before servicing.
■ Do not use outdoors or on wet surfaces.
■ Do not allow children to operate vacuum
cleaner or use as a toy.
■ Close attention is necessary when used by or
■
■
■
■
■
■
■
■
■
■
near children.
Do not use for any purpose other than described
in this User’s Guide.
Use only manufacturer’s recommended
attachments.
Do not use with damaged cord or plug.
If appliance is not working as it should,
has been dropped, damaged, left outdoors,
or dropped into water, have it repaired at an
authorized service center.
Do not pull or carry by cord, use cord as a
handle, close a door on cord, or pull cord
around sharp edges or corners. Do not run
appliance over cord. Keep cord away from
heated surfaces.
Do not unplug by pulling on cord. To unplug,
grasp the plug, not the cord.
Do not handle vacuum cleaner or plug with
wet hands.
Do not put any object into openings.
Do not use with any opening blocked; keep
openings free of dust, lint, hair, and anything
that may reduce air flow.
Keep hair, loose clothing, fingers, and all parts
of body away from openings and moving parts.
Turn off all controls before plugging or
■
■
■
■
fluid, gasoline, kerosene, etc.) or use in the
presence of explosive liquids or vapors.
Do not pick up toxic material (chlorine bleach,
ammonia, drain cleaner, etc.).
Do not use vacuum cleaner in an enclosed
space filled with vapors given off by oil base
paint, paint thinner, some moth proofing
substances, flammable dust, or other
explosive or toxic vapors.
Do not pick up hard or sharp objects such as
glass, nails, screws, coins, etc.
Do not pick up anything that is burning
or smoking, such as cigarettes, matches, or
hot ashes.
Do not use without filters in place.
Use only on dry, indoor surfaces.
Keep appliance on a level surface.
Do not carry the vacuum cleaner while it
is running.
SAVE THESE
INSTRUCTIONS FOR
FUTURE USE
THIS APPLIANCE HAS
A POLARIZED PLUG.
To reduce the risk of electric shock, this appliance has
a polarized plug (one blade is wider than the other).
This plug will fit in a polarized outlet only one way. If
the plug does not fit fully in the outlet, reverse the
plug. If it still does not fit, contact a qualified electrician
to install a proper outlet. Do not change the plug in
any way.
This model is for household use only.
3
Cord Clip
Hose Clip
Handle
Stretch Hose
Crevice Tool
Carrying
Handle
Extension Wand
Quick Reach®
Handle
Hose Wand
Combination
Dusting Brush/
Upholstery Tool
Hose
Wand Base
Quick Release
Cord Wrap
Louvers
Power Cord
Upper Tank
Power Switch
Handle
Release
Pedal
Dirt Container
Filter Cup
Foot Hose
Headlight
Height
Adjustment
Knob
Inner and Outer
Circular Filters
Lock ’n Seal™
Lever
Post-Motor
Filter
Powerfoot
Furniture Protection
Guard
CAUTION:
4
Do not plug in your vacuum
cleaner until you are familiar
with all instructions and
operating procedures.
How To Use This Guide
This User’s Guide has been designed to help
you get the most satisfaction from your BISSELL
Bagless. You’ll find assembly and operating instructions, safety precautions, as well as maintenance
and troubleshooting instructions. Please read this
Guide thoroughly before assembling your vacuum
cleaner.
Pay particular attention to the product diagram,
assembly instructions, and part names. Locate and
organize all parts before assembly. Familiarize
yourself with the parts and where they fit. Following
this User’s Guide will greatly enhance your ability
to get the most performance from your BISSELL
Bagless for many years.
WARNING:
Plastic film can be
dangerous. To avoid
danger of suffocation, keep away from
babies and children.
How To Put It Together
The only tool you’ll need to assemble your vacuum
cleaner is a screwdriver.
Attach Handle To Vacuum
1. Locate the vacuum Handle and remove the screw
packet taped to the base of the Handle.
2. Stand the vacuum upright and place the Handle on the
top of the vacuum body as shown.
3. Insert the screws provided from the screw packet into
the existing holes on each side. Tighten securely with
a screwdriver.
Attach Vacuum Hose and Tools
™
1. Attach the Twist ‘n Snap Hose by lining up the tabs on
the base with the corresponding notches on the back of
the vacuum as shown.
2. Turn the Twist ‘n Snap Hose to the right to lock the hose
into place.
3. Grasping the Quick Reach Handle, slide the end of the
Hose Wand onto the Hose Wand Base. Snap the Hose
into the Hose Clip.
NOTE: The Powerfoot will not operate
effectively unless the Hose Wand is
firmly attached.
5
Attach Vacuum Hose and Tools Continued
4. Slide the Extension Wand and the Crevice Tool together
into the storage clip on the side of the vacuum.
5. Snap the Combination Tool into the storage clip on the back
of the vacuum.
How To Use Your Vacuum
Handle Positions
Press the Handle Release Pedal with your foot to place
your vacuum in one of three cleaning positions.
1. Upright- For storage and above floor cleaning with tools.
2. Normal Cleaning- Press Handle Release Pedal once.
Use for most household floor cleaning tasks.
3. Low Cleaning- With the vacuum in normal cleaning posi-
tion, press Handle Release Pedal again. Use for reaching
under low furniture such as tables, chairs or beds.
Height Adjustment
The Powerfoot/Rotating Floor Brush can be
adjusted to clean several floor surfaces.
NOTE: For optimal cleaning performance,
adjust to the lowest practical setting. If
your cleaner is difficult to push, adjust to
the next higher setting.
1. Place Handle in Upright Position.
2.
Turn Height Adjustment Knob to desired setting.
Lowest Setting For bare floors.
Medium Settings For short and medium
pile carpets.
Highest Setting For plush pile carpet.
3. Place the Handle in the normal cleaning position and
the Powerfoot will adjust to the setting chosen.
NOTE: You may also adjust the setting
while in the normal cleaning position.
6
CAUTION:
Before using your vacuum,
make sure that the Dirt
Container is in locked position and that all filters (Inner
Circular, Outer Circular,
Pre-Motor and Post-Motor) are
in place. Do not operate your
vacuum without these filters.
Tip:
Before cleaning under
low furniture, check
area first for objects
that might harm the
unit or block the
Vacuum Hose.
Tip:
Your vacuum features
a Quick Release Cord
Wrap. To remove the
Power Cord quickly
and easily, rotate the
Upper Cord Wrap
towards floor, and
slip Power Cord from
Upper and Lower
Cord Wraps.
Transporting Cleaner
1. To move your cleaner from room to
room, put the Handle in the upright
position, tilt the cleaner back on its rear
wheels and push forward.
2. The cleaner can also be moved by
using the Carrying Handle on the back.
Carrying Handle
Special On-Board Tools
Your BISSELL Bagless is not only
a powerful carpet and rug vacuum
cleaner, it’s also a versatile above floor
vacuum cleaner when you select one
of the special tools.
1. Raise Handle to Upright Position.
2. Grasp the Quick Reach Handle and lift
Hose Wand to separate from suction
intake opening.
NOTICE:
The Floor Brush will continue to rotate
while you use your vacuum for above
floor cleaning. To prevent carpet
damage, do not lean on the vacuum
or let the Powerfoot tilt forward.
3. Attach tools by firmly pushing onto
Vacuum Hose or Extension Wand.
Combination Dusting Brush/
Upholstery Tool:
Two types of cleaning tools are included in
one attachment: rotate for desired tool.
■ Use Brush side to dust furniture,
blinds, books, lamps, shelves, and
baseboards.
■ Use Upholstery side for curtains,
draperies, cushions, fabrics.
Crevice Tool:
Use in tight narrow spaces.
Extension Wand:
Use with desired attachment for a
longer reach.
CAUTION:
The Rotating Floor Brush
continues to rotate while tools are in use.
To reduce the risk of injury from moving
parts, always move the cleaner with the
Carrying Handle at the back of the cleaner.
Always place vacuum cleaner on floor with
Handle in Upright position when using tools.
Never place your fingers under the cleaner
when it is running. Never place Powerfoot
on furniture or uneven surfaces. Do not
place vacuum cleaner close enough
to objects to pull them into rotating brush.
Tip:
Hair, string and small
objects can block
the Vacuum Hose
or Tools. Check
them occasionally for
obstructions.
7
Power Cord Storage
When you are done using your vacuum, return it
to the Upright position and store the Power Cord.
1. Turn vacuum cleaner off.
2. Unplug Power Cord by grasping the polarized plug (NOT
the cord) and disconnect from outlet.
3. Loop Power Cord around Cord Wraps on side of
vacuum cleaner.
NOTICE:
While vacuuming, certain carpets
and low humidity conditions may
generate small static discharges.
The discharges are entirely
harmless and are not associated
in any way with the main
power supply.
4. Clip molded plug to Power Cord to secure.
How To Maintain Your Vacuum
To maintain maximum cleaning performance, the
following maintenance steps must be performed:
WARNING:
To reduce the risk of
electric shock, turn Power
Switch OFF and disconnect polarized
plug from electrical outlet
before performing
maintenance or
troubleshooting checks.
1. Empty the Dirt Container when the dirt reaches the
“Full” line on the side.
2. Check the Inner and Outer Circular Filters, and the
Pre-Motor Filter at least once a month and clean or
replace as needed.
3. Clean or replace the Post-Motor Filter every three to
six months.
Note: More frequent filter cleaning or
replacing may be necessary if you are
vacuuming new carpet, fine dust, or have
allergy concerns. Follow the instructions on
the following pages to perform these simple
maintenance steps.
Tip:
For maximum cleaning
performance, check
and clean or replace all
filters as suggested.
Empty Dirt Container
The Dirt Container needs to be emptied when the dirt
reaches the “Full” line on the side of the Container.
Full Line
1. Unplug cleaner from electrical outlet.
2. Slide the Lock ‘n Seal Lever to the "Unlock" position.
3. Grasp handle and pull the Dirt Container straight out to
remove from vacuum.
4. Empty dirt into garbage container.
5. Put the Dirt Container back in the vacuum and slide the
lever to the "Lock" position.
Note: The Dirt Container may be washed in
warm water with a mild detergent. Remove
the Filter Cup from the bottom before
washing. Reassemble and make sure it is
completely dry before using again.
8
Unlock
Position
Lock Position
Cleaning The Inner & Outer Circular Filters
Use only BISSELL Style 10 Replacement Filters in your BISSELL
Bagless.
1. Unplug the cleaner from electrical outlet.
2. Remove the Dirt Container as described in the previous section. Grasp
the Filter Cup located at the bottom of the Dirt Container and twist
counterclockwise to unlock and remove.
3. Grasp the Circular Filters and twist to unlock. Pull straight
up to remove.
4. Separate the Outer foam and Inner pleated Circular Filters. Wash each
individually by hand in warm water. Mild detergent may be used if
desired. Rinse well, then air dry thoroughly before putting them back
together and replacing in Filter Cup.
5. The Filter Cup may be washed in warm water with a mild detergent.
Make sure it is completely dry before reassembling with filters.
6. The Upper Tank and Louvers may also be wiped clean with a damp
cloth. Reach underneath the Upper Tank and turn the rim of the Louvers
to unlock. Pull straight down to remove.
WARNING:
Do not operate cleaner
Cleaning the Pre-Motor Filter
with damp or wet
filters or without all
filters in place.
1. Unplug the cleaner from electrical outlet.
2. The Pre-Motor Filter protects the motor from debris. It is located
underneath the Dirt Container and Filter Cup in the center of the
round part of the Lock ‘n Seal Lever.
Pre-Motor
Filter
3. Remove the small round Filter and any debris on top of it. Rinse well
under warm water, then air dry thoroughly before replacing.
Cleaning the Post-Motor Filter
Use only BISSELL Style 10 Replacement Filters in your
BISSELL Bagless.
1. Unplug the cleaner from electrical outlet.
Post-Motor Filter
2. The Post-Motor Filter assists in the filtration process to return clean
air to the room. It is located behind the door on the front of the
cleaner. When the filter becomes dirty, open the door, remove the
filter and clean.
3. The Post-Motor Filter may be hand washed in warm water. Mild
detergent may be used if desired. Rinse well, then air dry thoroughly
before replacing.
4. Replace the door by inserting the tabs on the left side and snapping the
right side into place.
9
Check Rotating Floor Brush and Drive Belt
You should check your vacuum cleaner’s Rotating
Floor Brush and Drive Belt regularly for wear or
damage. You should also clean the brush and brush
ends of strings, hair, and carpet fibers. These can
wrap around the brush and hamper its ability to
effectively clean your carpet. Also remove any debris
that has accumulated under the brush cover.
WARNING:
To reduce the risk of
injury from moving parts,
turn off vacuum cleaner
and disconnect Power
Plug from electrical outlet.
1. Unplug cleaner from electrical outlet.
2. Place handle in Low position and turn vacuum cleaner over so
bottom side is up.
3. Remove the four screws as shown with a Phillips head
screwdriver. Lift the Brush Cover off.
4. Grasp Rotating Floor Brush at both ends and lift.
Brush
Cover
5. Clean strings, hair and other debris from Rotating Floor
Brush, paying particular attention to brush ends.
6. Clean strings, hair and other debris from Motor Pulley and Drive
Belt areas.
7. Check Drive Belt carefully for wear, cuts or stressed areas.
Replace if worn.
Motor
Pulley
8. Check Air Passageway for obstructions. Remove debris from
this area.
Air Passageway
Replace Drive Belt
Use only BISSELL Style 10 Replacement Belts (#32074)
in your BISSELL Bagless.
1. Unplug cleaner from electrical outlet.
2. With Rotating Floor Brush removed from vacuum cleaner
(Steps 1-4 of Check Rotating Floor Brush and Drive Belt),
grasp old Drive Belt and remove from Motor Pulley. Discard
old Drive Belt.
3. Place new Drive Belt over Motor Pulley and stretch other
end over Rotating Floor Brush in the space between
the bristles.
4. Place ends of Rotating Floor Brush down into slots on sides
as shown.
Press here
5. Turn Rotating Floor Brush by hand several times in the
direction of Motor Pulley. If properly installed, Drive Belt will
center itself on Rotating Brush.
6. Reposition Brush Cover and four screws. Make sure end of
Brush Cover is snapped into place.
10
Brush
Cover
Replace Lightbulb
Use only BISSELL Replacement Bulbs in your
BISSELL Bagless.
1. Unplug cleaner from electrical outlet
2. Using a flat screwdriver, table knife or coin, insert into the
slot on the right of the lens and gently push inner latch to
the left as shown to remove the lens.
3. Determine the light bulb type of your vacuum:
Standard Bulb (#203-1297) – approximately 1” long, flat end
Large Bulb (#203-1007) – approximately 2” long, round end
Standard Bulb
4. Standard Bulb – remove the bulb from the socket by
grasping bulb and pulling straight out. Install the new bulb
by pushing it gently into the socket until the bulb snaps
into place.
Large Bulb - remove the bulb from the socket by pushing
bulb in gently and turning it towards brush. Install the new
bulb by pushing it gently into the socket and turning away
from the brush.
Large Bulb
5. Reposition lens, by inserting tab on left side and then
pushing the right side back into place.
Louvers
Clearing Clogs
Low suction, poor pickup, or no suction may be due
to a clog in the vacuum cleaner. If you notice a change
in the sound of the motor or a reduction in the spinning action in the Dirt Container, check for clogs.
Suction
Inlet
1. Unplug cleaner from electrical outlet.
2. Empty Dirt Container.
3. Check Upper Tank and Louvers for build up or clogs.
Check to make sure Louvers are installed correctly. To
unlock the Louvers, grasp the rim and turn toward the left.
Pull straight down to remove. If the Louvers are missing
or not locked into place, check and clear the tube in the
center of the Dirt Container.
4. Remove the Twist ‘n Snap Hose from the vacuum by
turning to the left. Check the Suction Inlet, Hose and Hose
Wand for clogs. Remove any clogs from the hose using a
long, narrow object.
Hose
Wand Base
5. Check the Foot Hose for clogs. If needed, remove the screw
attaching the Hose Wand Base to the vacuum. Straighten
the Foot Hose and unclog with a long, narrow object.
6. If the clog persists, follow the instructions for Checking
the Rotating Floor Brush on page 10 and inspect the Air
Passageway for obstructions.
Air Passageway
11
Troubleshooting
WARNING:
To reduce the risk of injury
from moving parts and/
or electrical shock, turn
Power Switch OFF and
disconnect polarized plug
from electrical outlet
before performing
troubleshooting checks.
Vacuum cleaner won’t run
Possible Causes
1
2
Power cord not plugged in
Blown fuse/tripped breaker
Remedies
1
2
Check electrical plug
Check/Replace fuse or
reset breaker
Vacuum cleaner won’t pick up dirt
Possible Causes
1
Incorrect Height Adjustment
2
Hose not attached to suction opening
3
Twist ‘n Snap Hose not securely attached
4
Crack or hole in Hose
Broken or worn Drive Belt
Rotating Floor Brush bristles worn
Rotating Floor Brush jammed
5
6
7
11
Clog in vacuum
Dirt Container full
Dirt Container not installed properly
Filters are dirty
12
Louvers missing or installed incorrectly
8
9
10
Remedies
Adjust Powerfoot to correct
height setting
2 Grasp Quick Reach Handle and
firmly push Hose Wand onto the
suction opening
3 Make sure Twist ‘n Snap Hose is
snapped into locked position
4 Check Hose and replace if needed
5 Replace Drive Belt, see pg. 10
6 Replace brush
7 Remove brush and clean debris from
brush ends
8 Clear clog, see pg. 11
9 Empty Dirt Container
10 Position correctly and lock in place
11 Check and clean Inner and Outer
Circular Filters, Pre-Motor and
Post-Motor Filters
12 Check for a clog in the tube in the
center of the Dirt Container, clear
and properly install Louvers
1
Tools won't pick up dirt
Possible Cause
1
2
12
Crack or hole in Hose
Clog in vacuum
Remedies
1
2
Check Hose and replace if needed
Clear clog, see pg. 11
Troubleshooting Continued
Tools won't pick up dirt, continued
Possible Cause
Remedies
5
Dirt Container full
Dirt Container or Upper Tank
not installed properly
Filters are dirty
6
Louver missing or installed incorrectly
3
4
3
4
5
6
Empty Dirt Container
Position correctly and
lock in place
Check and clean Inner and Outer
Circular Filters, Pre-Motor and
Post-Motor Filters
Check for a clog in the tube in the
center of the Dirt Container, clear
and properly install Louvers
Vacuum cleaner is difficult to push
Possible Causes
Remedies
1
Incorrect Height Adjustment
1
2
Rotating Floor Brush not rotating
2
Adjust Powerfoot to correct
height setting
Check Drive Belt and Brush
Visible dirt escaping from cleaner
Possible Causes
Remedies
2
Dirt Container full
Filters missing or installed incorrectly
2
3
Dirt Container installed incorrectly
3
4
Filter Cup installed incorrectly
4
1
1
Empty Dirt Container
Check Inner and Outer Circular
Filters and Post-Motor Filter for
correct installation
Pull out and re-insert Dirt
Container correctly
Remove Dirt Container and make
sure Filter Cup is fully attached
If suggested solutions do not correct the problem, call:
BISSELL Consumer Services
1-800-237-7691
Monday - Friday
Saturday
8 a.m. — 10 p.m. ET
9 a.m. — 8 p.m. ET
or visit the BISSELL website - www.bissell.com
13
Replacement Parts – BISSELL Bagless Series
You may purchase replacement parts from your retailer, by calling BISSELL Consumer Services
or by visiting our website. To locate a retailer near you, or to place an order using Visa,
MasterCard, Discover or American Express, call
BISSELL Consumer Services
1-800-237-7691
Monday - Friday
8 a.m. — 10 p.m. ET
Saturday
9 a.m. — 8 p.m. ET
Or visit our Website - www.bissell.com
Item Part No.
Part Name
1
2
3
4
5
6
7
8
9
10
11
12
13
Style 7/9/10 Drive Belt (2-Pack)
Large Headlight Bulb (Select Models Only)
Standard Headlight Bulb (Select Models Only)
Crevice Tool
Combination Dusting Brush / Upholstery Tool
Extension Wand
Wire Reinforced Twist ‘n Snap Vacuum Hose (Select Models Only)
Twist ‘n Snap Vacuum Hose (Select Models Only)
Brush Roll
Style 9/10 Inner & Outer Circular Filter Set
Style 9/10 Inner Circular Filter only
Style 10 Outer Circular Filter and Post-Motor Filter Set
Pre-Motor Filter
1
2/3
4
5
6
7/8
9
10
11
12
13
14
32074
203-1007
203-1297
203-1063
203-1099
203-1022
203-1216
203-2126
203-1096
32064
32065
32066
203-1215
BISSELL Consumer Services
For information about repairs or replacement parts, or
questions about your warranty, call:
BISSELL Consumer Services
1-800-237-7691
Monday - Friday
Saturday
8 a.m. — 10 p.m. ET
9 a.m. — 8 p.m. ET
Or write:
BISSELL Homecare, Inc.
PO Box 3606
Grand Rapids, MI 49501
ATTN: Consumer Services
Or visit the BISSELL website - www.bissell.com
When contacting BISSELL, have model number of unit available.
Please record your Model Number: ___________________
Please record your Purchase Date: ___________________
NOTE: Please keep your original sales receipt. It is your warranty.
15
Warranty
This warranty gives you specific legal rights, and you may also have other rights which may vary from state to
state. If you need additional instruction regarding this warranty or have questions regarding what it may cover,
please contact BISSELL Consumer Services by E-mail, telephone, or regular mail as described below.
Limited One Year Warranty
Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, upon receipt of the product BISSELL Homecare,
Inc. will repair or replace (with new or remanufactured components or products), at BISSELL’s option, free of
charge from the date of purchase by the original purchaser, for one year any defective or malfunctioning part.
See information below on "If your BISSELL product should require service".
This warranty applies to product used for personal, and not commercial or rental service. This warranty does not
apply to fans or routine maintenance components such as filters, belts, or brushes. Damage or malfunction caused
by negligence, abuse, neglect, unauthorized repair, or any other use not in accordance with the User's Guide is
not covered.
If your BISSELL product should require service:
Contact BISSELL Consumer Services to locate a BISSELL Authorized Service Center in your area.
If you need information about repairs or replacement parts, or if you have questions about your
warranty, contact BISSELL Consumer Services.
Website or E-mail:
www.bissell.com
Use the “Customer Services” tab.
Or Call:
BISSELL Consumer Services
1-800-237-7691
Monday - Friday 8 a.m. - 10 p.m. ET
Saturday 9 a.m. - 8 p.m. ET
Or write:
BISSELL Homecare, Inc.
PO Box 3606
Grand Rapids MI 49501
ATTN: Consumer Services
BISSELL HOMECARE INC. IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY
NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT. BISSELL’S LIABILITY WILL NOT EXCEED THE
PURCHASE PRICE OF THE PRODUCT.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so
the above limitation or exclusion may not apply to you.
*EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER
ORAL OR WRITTEN. ANY IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION
OF LAW, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE ONE YEAR DURATION
FROM THE DATE OF PURCHASE AS DESCRIBED ABOVE.
Some states do not allow limitations on how long an implied warranty lasts,
so the above limitation may not apply to you.
16
©2005 BISSELL Homecare, Inc
Grand Rapids, Michigan
All rights reserved. Printed in Korea
Part Number 310-5825
Rev 10/05
Visit our website at:
www.bissell.com
Download PDF

advertising