Bissell 92L3 Vacuum Cleaner User Manual

PowerClean
®
B A G L E S S
V A C U U M
USER’S GUIDE
92L3 SERIES
3
Safety Instructions
4
Product View
5-6
Assembly
6-10
Operations
11-16
Maintenance and Care
16-17
Troubleshooting
18
Consumer Services
18
Replacement Parts
19
Additional Accessories
20
Warranty
ug110-4054_92L3_608.indd 1
8/8/08 2:36:26 PM
Thanks for buying a BISSELL Vacuum
We’re glad you purchased a BISSELL vacuum. Everything we know about
floor care went into the design and construction of this complete,
high-tech home cleaning system.
Your BISSELL vacuum is well made, and we back it with a limited one
year warranty. We also stand behind it with a knowledgeable, dedicated
Consumer Services department, so, should you ever have a problem, you’ll
receive fast, considerate assistance.
My great-grandfather invented the floor sweeper in 1876. Today, BISSELL is
a global leader in the design, manufacture, and service of high quality
homecare products like your BISSELL vacuum .
Thanks again, from all of us at BISSELL.
Mark J. Bissell
Chairman, President & CEO
22
www.bissell.com
ug110-4054_92L3_608.indd 2
800.237.7691
8/8/08 2:36:27 PM
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic
precautions should be observed, including
the following:
READ ALL INSTRUCTIONS
BEFORE USING YOUR
UPRIGHT VACUUM.
Always connect to a polarized outlet (left slot is wider
than right). Unplug from outlet when not in use and
before conducting maintenance.
WARNING: To reduce
the risk of fire, electric shock,
or injury:
■ Do not modify the polarized plug to fit a
non-polarized outlet or extension cord.
■ Do not leave vacuum cleaner unattended when it
is plugged in.
■ Unplug from outlet when not in use and
before servicing.
■ Unplug before attaching the TurboBrush.
■ Do not use outdoors or on wet surfaces.
■ Do not allow children to operate vacuum
cleaner or use as a toy.
■ Close attention is necessary when used by or
■ Turn off all controls before plugging or unplugging
vacuum cleaner.
■ Use extra care when cleaning stairs.
■ Do not pick up flammable materials (lighter fluid,
■
■
■
■
■
■
■
■
gasoline, kerosene, etc.) or use in the presence of
explosive liquids or vapors.
Do not pick up toxic material (chlorine bleach,
ammonia, drain cleaner, etc.).
Do not use vacuum cleaner in an enclosed space
filled with vapors given off by oil base paint, paint
thinner, some moth proofing substances, flammable
dust, or other explosive or toxic vapors.
Do not pick up hard or sharp objects such as
glass, nails, screws, coins, etc.
Do not pick up anything that is burning or smoking,
such as cigarettes, matches, or hot ashes.
Do not use without filters in place.
Use only on dry, indoor surfaces.
Keep appliance on a level surface.
Do not carry the vacuum cleaner while it
is running.
SAVE THESE
INSTRUCTIONS FOR
FUTURE USE
near children.
■ Do not use for any purpose other than described in
■
■
■
■
■
■
■
■
this user’s guide.
Use only manufacturer’s recommended
attachments.
Do not use with damaged cord or plug.
If appliance is not working as it should, has been
dropped, damaged, left outdoors, or dropped
into water, have it repaired at an authorized
service center.
Do not pull or carry by cord, use cord as a handle,
close a door on cord, or pull cord around sharp
edges or corners. Do not run appliance over cord.
Keep cord away from heated surfaces.
Do not unplug by pulling on cord. To unplug, grasp
the plug, not the cord.
Do not handle vacuum cleaner or plug with
wet hands.
Do not put any object into openings. Do not use with
any opening blocked; keep openings free of dust,
lint, hair, and anything that may reduce air flow.
Keep hair, loose clothing, fingers, and all parts of
body away from openings and moving parts.
www.bissell.com
ug110-4054_92L3_608.indd 3
THIS APPLIANCE
HAS A POLARIZED
PLUG.
To reduce the risk of electric shock, this appliance has a
polarized plug (one blade is wider than the other). This plug
will fit in a polarized outlet only one way. If the plug does
not fit fully in the outlet, reverse the plug. If it still does not
fit, contact a qualified electrician to install a proper outlet.
Do not change the plug in any way.
This model is for household use only.
800.237.7691
3
8/8/08 2:36:28 PM
Product view
Handle
Hose Clip
Stretch Hose
Dusting Brush/
Upholstery Tool
TurboBrush®
Quick Release™
Cord Wrap
Carry Handle
Crevice Tool
Twist ‘n Snap™
Hose
Power Switch
Inner Cyclone
Power
Cord
Hose
Wand
Extension Wand
Upper Tank
HEPA Media
Post Motor Filter
Easy Empty™
Dirt Container
Washable
Pre-Motor Filter
Lock ‘n Seal® Lever
Headlight
Handle Release
Pedal
Foot
Window
Height Adjustment
Knob
Hose Wand Base
Wide Cleaning Foot
4
www.bissell.com
ug110-4054_92L3_608.indd 4
800.237.7691
8/8/08 2:36:28 PM
CAUTION:
Do not plug in your
Assembly
vacuum cleaner until
you are familiar with
all instructions and
operating procedures.
The only tool you’ll need to assemble your
vacuum cleaner is a Phillips screwdriver.
Attach handle to vacuum
1.
Locate the handle and cord wrap. Remove
the screw packet taped to the handle.
2.
Stand the vacuum upright and from the
rear of the unit, slide the base of the handle
firmly into the grooves at the top of the
vacuum body.
3.
Ensure that the handle fits firmly to the
vacuum body. If there are any gaps, continue
to push firmly until the handle is secure.
4.
Insert the provided screw into the existing
hole, attaching the handle to the body of the
vacuum. Tighten securely with a screwdriver.
2.
4.
www.bissell.com
ug110-4054_92L3_608.indd 5
800.237.7691
5
8/8/08 2:36:29 PM
Assembly
1.
3.
Attach vacuum hose and tools
1.
Attach the Twist ‘n Snap™ Hose by lining up
the tabs on the base with the corresponding
notches on the back of the vacuum as shown.
2.
Turn the Twist ‘n Snap Hose to the right to
lock the hose into place.
3.
Grasping the Quick Reach Handle, slide the
end of the Hose Wand onto the Hose Wand
Base. Snap the Hose into the Hose Clip.
NOTE: The vacuum will not operate effectively
unless the hose wand is firmly attached.
4.
Slide the extension wand and crevice tool
into the storage clip on back of vacuum.
5.
Slide the dusting brush/upholstery tool into
the storage clip on back of vacuum.
6.
Attach the Contour Tool to the back
of the vacuum by inserting tool into
storage clip.
7.
Store the TurboBrush on the front of the
handle by lining up the TurboBrush base
with the base of the holder then push back
to snap into place.
Operations
Power switch
The Power Switch is located on the left side of
the vacuum. Push the rocker switch “ON” (I)
to vacuum, and “OFF” (O) when cleaning is
complete.
Twist 'n
Snap Hose
7.
CAUTION:
Before using your vacuum,
make sure that the dirt
container is in the locked
position and that all filters
(pre-motor and HEPA media
post-motor) are in place.
Do not operate your vacuum
without these filters.
NOTICE:
For above floor cleaning, the floor
brush will continue to rotate, but
is raised above floor. To prevent
carpet damage, do not lean on
the vacuum or let the powerfoot
tilt forward.
CAUTION:
To avoid personal injury
and to prevent the cleaner
from falling when cleaning
stairs, always place it at
the bottom of the stairs.
6
www.bissell.com
ug110-4054_92L3_608.indd 6
800.237.7691
8/8/08 2:36:31 PM
Operations
1.
2.
Handle positions
Press the handle release pedal, located on the lower
3.
left side of the vacuum, with your foot to place your
vacuum into one of three cleaning positions.
1. Upright – For storage and above floor
cleaning with tools.
2. Normal Cleaning – Press handle release
pedal once. Position used for most
household floor cleaning tasks.
3. Low Cleaning – With the vacuum in normal
cleaning position, press handle release pedal Before cleaning under low furniture, check
again. Use for reaching under low furniture
area first for objects that might harm the unit
such as tables, chairs or beds.
Tip:
or block the vacuum hose.
Height adjustment
1.
The powerfoot/rotating floor brush on your vacuum
can be adjusted to clean several floor surfaces.
NOTE: For optimal cleaning performance,
adjust to the lowest practical setting. If
your cleaner is difficult to push, adjust to
the next higher setting.
1.
Turn height adjustment knob to desired setting.
Bare Floor
For non-carpeted,
indoor surfaces
Lowest Setting
For short pile carpets
Medium Setting For short and medium
pile carpets
Highest Setting For plush pile carpet
www.bissell.com
ug110-4054_92L3_608.indd 7
Height Adjustment Knob
800.237.7691
7
8/8/08 2:36:32 PM
Operations
Transporting cleaner
1.
To move your cleaner from room to room,
put the handle in the upright position, tilt
the cleaner back on its rear wheels and
push forward.
2.
The cleaner can also be moved by using
the carry handle.
1.
Special on-board tools
Your vacuum is not only a powerful carpet and
rug cleaner, it’s also a versatile above floor
vacuum cleaner when you select one of the
special tools.
1. Raise the handle to the upright position.
2.
Grasp the hose wand handle to separate
from hose wand base.
3.
Attach tools by firmly pushing onto vacuum
hose, hose wand or extension wand. Be
sure the hose and tool fit snuggly together
by twisting tightly.
Dusting Brush/Upholstery Tool: Two types of
cleaning tools in one attachment.
• Use the dusting brush to dust
furniture, blinds, books, lamps,
shelves and baseboards.
• Slide the brush off to use the
upholstery tool on cushions,
draperies and fabrics.
correct way to carry
Dusting Brush/
Upholstery Tool
Crevice Tool
Extension Wand
Hose Wand
Hose Wand
Base
8
www.bissell.com
ug110-4054_92L3_608.indd 8
800.237.7691
8/8/08 2:36:33 PM
Operations
Special on-board tools (continued)
Crevice Tool: Use in tight narrow spaces.
Extension Wand: Use with desired attachment for
a longer reach.
Dusting Brush/
Upholstery Tool
Hose Wand: Use with desired attachment for a
longer reach or for cleaning hard to reach
places.
Crevice Tool
Extension Wand
TurboBrush: Use rotating brush action for small
flat areas such as cushions and beds.
Hose Wand
NOTE: Press gently down and pull towards
you in a raking motion. Too much pressure
will cause the brush to stop rotating.
Hose Wand
Base
TurboBrush
Tip:
Hair, string and small objects can block
the vacuum hose or tools. Check them
occasionally for obstructions.
CAUTION:
The rotating floor brush continues to rotate while tools are in use. To reduce
the risk of injury from moving parts, always move the cleaner with the carrying
handle. Always place vacuum cleaner on the floor with handle in upright position
when using tools. Never place your fingers under the cleaner when it is running.
Never place powerfoot on furniture or uneven surfaces. Do not place vacuum
cleaner close enough to objects to pull them into rotating brush.
www.bissell.com
ug110-4054_92L3_608.indd 9
800.237.7691
9
8/8/08 2:36:35 PM
Operations
Power cord usage
1.
10
To use your vacuum, remove the cord and
plug it into an electrical outlet. For your
convenience, there is a quick release cord
wrap for easy cord removal. There is also
a cord clip that is part of the upper cord
wrap where you can attach the cord when
vacuuming.
2.
When you are finished cleaning, turn
vacuum cleaner off.
3.
Unplug power cord by grasping the polarized
plug (NOT the cord) and disconnect from outlet.
4.
Loop power cord around cord wraps on side
of vacuum cleaner. Be sure to first return the
quick release cord wrap back to its original
position before wrapping the cord.
5.
Clip molded plug to power cord to secure.
www.bissell.com
ug110-4054_92L3_608.indd 10
1.
Quick Release
Cord Wrap
800.237.7691
8/8/08 2:36:37 PM
Maintenance and care
To maximize your cleaning performance and
extend the life of your vacuum, it is very
important that you empty your dirt container
and check and clean your filters frequently.
Perform the following maintenance steps:
1. Empty the dirt container when the dirt reaches
the “Full” line on the container, or more frequently
to prevent overfills. For best performance, empty
after each use.
2.
3.
WARNING:
To reduce the risk of electric
shock, turn power switch OFF
and disconnect polarized plug
from electrical outlet before
performing maintenance or
troubleshooting checks.
Check the pre-motor filter and post-motor HEPA
media filter at least once a month, clean or
replace as needed.
Replace the post-motor HEPA media filter
every three to six months.
Tip:
To maximize cleaning performance,
check and clean or replace all filters
as suggested.
NOTE: More frequent filter cleaning may be
necessary if you are vacuuming new carpet,
fine dust, or have allergy concerns. Follow
the instructions on the following pages to
perform these simple maintenance steps.
Empty dirt container
The dirt container should to be emptied before
the dirt reaches the “Full” line on the container.
1. Unplug the vacuum from electrical outlet.
2.
Slide the Lock ‘n Seal Lever to the “Unlock”
position.
3.
Grasp handle and pull the dirt container
straight out to remove from the vacuum.
4.
Empty dirt into garbage container.
NOTE: Emptying the dirt container after
every use will help prevent over filling and
ensure that the vacuum is ready to go the
next time you clean.
2.
Unlock
4.
www.bissell.com
ug110-4054_92L3_608.indd 11
800.237.7691
11
8/8/08 2:36:38 PM
Maintenance and care
Cleaning the pre-motor and post-motor HEPA media filter
1.
Unplug the vacuum from electrical outlet.
2.
The pre-motor filter protects the motor from
dirt particles. It is located in the slide out
tray underneath the dirt container. If the filter
becomes dirty, pull out the tray, lift out the
foam filter pad and clean it.
Post-Motor
HEPA
Media
Filter
NOTE: The pre-motor filter may be hand washed
in cold water with mild detergent. Rinse well
Washable
and air dry thoroughly before replacing.
3.
Pre-Motor
Filter
The post-motor HEPA media filter assists in
the filtration process to return clean air to
the room. It is located behind the door on the
side of the vacuum. If the filter becomes dirty,
remove the door, remove the filter and replace.
WARNING:
Do not operate cleaner
NOTE: The post-motor filter is a
white, pleated HEPA media filter. This
filter is not washable and must be
replaced when it becomes dirty.
with damp or wet filters or
without all filters in place.
Check rotating floor brush and drive belt
You should check your vacuum cleaner’s rotating floor
brush and drive belt regularly for wear or damage. You
should also clean the brush and brush ends of strings,
hair and carpet fibers. This type of debris can wrap
around the brush and hamper its ability to effectively
clean your carpet. Also remove any debris that has
accumulated under the brush cover.
1. Unplug the vacuum from electrical outlet.
12
2.
Place handle in low position and turn vacuum
cleaner over so bottom side is facing up.
3.
Lift tab 1 and release the three latches in
order 2-4 marked. Lift off the brush cover.
4.
Grasp rotating floor brush at both ends and lift.
5.
Clean strings, hair and other debris from
rotating floor brush, paying particular
attention to brush ends.
6.
Clean strings, hair and other debris from
motor pulley and drive belt areas.
7.
Check drive belt carefully for wear, cuts or
stressed areas.
8.
Check air passageway for obstructions.
Remove debris from this area.
WARNING:
To reduce the risk of injury
from moving parts, turn
vacuum cleaner off and
disconnect power plug
from electrical outlet.
3.
1
4
2
www.bissell.com
ug110-4054_92L3_608.indd 12
3
8.
Motor Pulley
Air Passageway
800.237.7691
8/8/08 2:36:39 PM
Maintenance and care
Replace drive belt
1.
Unplug the vacuum from electrical outlet.
2.
With rotating floor brush removed from
vacuum cleaner (Steps 1-4 of check rotating
floor brush and drive belt), grasp old drive
belt and remove from motor pulley. Discard
the old drive belt.
Motor Pulley
3.
Place new drive belt over motor pulley and
loop other end over rotating floor brush in
the space between the bristles.
3.
NOTE: It is important that you use only
genuine BISSELL replacement belts.
Generic belts may not meet the exact
specifications required to keep your
vacuum operating at its peak performance.
The use of unbranded belts could lead to
early failure of the vacuum and could void
your warranty.
4.
Pull the rotating floor brush firmly into
position, stretching the drive belt, and place
ends of rotating floor brush down into the
slots on sides as shown. Alignment of brush
ends in slots may be necessary to fully
insert the brush.
5.
Turn rotating floor brush by hand several
times in the direction of motor pulley. If
properly installed, drive belt will center itself
on rotating brush crown.
6.
Insert front edge of brush cover, rotate into
place, and snap 3 latches.
www.bissell.com
ug110-4054_92L3_608.indd 13
800.237.7691
13
8/8/08 2:36:41 PM
Maintenance and care
Replacing lightbulb
1.
Unplug the vacuum from electrical outlet.
2.
Using a screwdriver, first remove 2 screws
on either side of lens and pull out to remove
the lens.
3.
Remove the bulb from the socket by
grasping the bulb and pulling gently. Install
the new bulb by pushing it gently into the
socket until the bulb snaps into place.
4.
Reposition the lens place cover back over
headlight and reinsert 2 screws.
2.
3.
4.
Maintaining TurboBrush®
The TurboBrush should be checked regularly for
clogs or debris wrapping around the brush.
1. Remove tool from hose or front of vacuum.
14
2.
Twist collar so opening is at the top and lift
top cover to remove.
3.
Remove the brush from the belt and clean
debris.
4.
Replace the brush inside the belt and place
ends into slots on sides as shown.
5.
Reposition top cover making sure to line up
inside tab at the front with the opening on
the cover. Twist collar until opening is at the
bottom to lock into place.
www.bissell.com
ug110-4054_92L3_608.indd 14
2.
4.
5.
800.237.7691
8/8/08 2:36:42 PM
Maintenance and care
Clearing clogs
Low suction or poor pickup may be due to a clog
in the vacuum cleaner. If you notice a change in
the sound of the motor, check for clogs.
1. Unplug the vacuum from electrical outlet.
2.
Empty dirt container.
3.
Check upper tank for build up or clogs.
4.
If you notice a clog in the upper tank,
remove the inner cyclone (see section
"Cleaning the upper tank" on page 16).
5.
Grasp the hose wand and separate it from
the hose wand base. Check for a clog in the
base, the wand or in the hose.
6.
Remove the Twist ‘n Snap hose from the vacuum
by turning to the left. Straighten the hose and
unclog with a long, narrow object such as a
broom handle.
7.
If the clog persists, follow the instructions for
"Checking the rotating floor brush and drive
belt" on page 12 and inspect the air
passageway for obstructions.
www.bissell.com
ug110-4054_92L3_608.indd 15
2.
5.
800.237.7691
15
8/8/08 2:36:46 PM
Maintenance and care
Cleaning the upper tank
1.
Grasp the inner cyclone and twist to the left
until the locking tabs stop the rotation. Pull
down from the upper tank to remove it.
2.
Wipe out the inside of the upper tank and the
inner cyclone with a damp cloth moistened
with water or a mild cleaning solution.
3.
If you desire to thoroughly clean the filtration
disk located in the upper portion of the inner
cyclone, hold the bottom of the cyclone and
turn filtration disk to the right and pull up to
remove.
4.
The inner cyclone and filtration disk may be
washed using a mild detergent. Be sure it
is completely dry before reassembling or
damage to your unit may result.
5.
Once cleaning is completed, reassemble the
filtration disk over the inner cyclone by
sliding it straight down on the top of the
inner cyclone and turning left. Be sure to line
up the tabs when reassembling for proper
installation.
6.
To replace the inner cyclone, slide it into the
upper housing. Be sure to line up the inner
cyclone by ensuring tabs on filtration disk
are positioned toward the front of the unit.
Push the inner cyclone in and rotate it to the
right until the locking tabs stop the rotation.
Troubleshooting
Vacuum cleaner won’t run
16
1.
3.
5.
6.
WARNING:
To reduce the risk of electric shock,
turn power OFF and disconnect
polarized plug from electrical outlet
before performing maintenance or
troubleshooting.
Possible causes
Remedies
1.
Power cord not plugged in
1. Check electrical plug
2.
Blown fuse/tripped breaker in home
2. Check/replace fuse or reset breaker
www.bissell.com
ug110-4054_92L3_608.indd 16
800.237.7691
8/8/08 2:36:47 PM
Troubleshooting
Vacuum cleaner won’t run (continued)
Possible causes
Remedies
3.
3. Unplug, check for damage, replace
as necessary
Damaged power cord
Vacuum cleaner and tools won’t pick up dirt
Possible causes
Remedies
1.
Incorrect height adjustment
1. Adjust powerfoot to correct height
2.
Hose not attached to suction opening
2. Firmly push hose wand into hose
wand base
3.
Twist 'n Snap hose not securely attached
3. Make sure Twist 'n Snap hose is snapped
into locked position
4.
Crack or hole in hose
4. Check hose and replace if needed
5.
Broken or worn drive belt
5. Replace drive belt, see page 13
6.
Rotating floor brush bristles worn
6. Replace brush
7.
Rotating floor brush jammed
7. Remove brush and clean debris from
brush ends
8.
Clog in vacuum
8. Clear clogs, see page 15
9.
Dirt container full
9. Empty dirt container
10. Dirt container not installed properly
10. Position correctly and lock in place
11. Filters are dirty
11. Check pre-motor and post-motor filters
12. TurboBrush is clogged or debris is wrapped
around the brush roll
12. See page 14 for Maintaining TurboBrush
Vacuum cleaner is difficult to push
Possible causes
Remedies
1.
1. Adjust powerfoot to correct height setting
Incorrect height setting
Visible dirt escaping from cleaner
Possible causes
Remedies
1. Dirt container full
1. Empty dirt container
2. Filters missing or installed incorrectly
2. Check pre-motor and post-motor filters for
correct installation
3. Dirt container installed incorrectly
3. Pull out and re-insert dirt container correctly
Other maintenance or service not included in the manual should be performed by an
authorized service representative.
Thank you for selecting a BISSELL product.
Please do not return this product to the store.
For any questions or concerns, BISSELL is happy to be of service.
Contact us directly at 1-800-237-7691.
www.bissell.com
ug110-4054_92L3_608.indd 17
800.237.7691
17
8/8/08 2:36:49 PM
BISSELL Consumer Services
For information about repairs or replacement parts, or questions about your warranty, call:
BISSELL Consumer Services
1-800-237-7691
Monday - Friday
Saturday
8 a.m. — 10 p.m. ET
9 a.m. — 8 p.m. ET
Or write:
BISSELL Homecare, Inc.
PO Box 3606
Grand Rapids MI 49501
ATTN: Consumer Services
Or visit the BISSELL website - www.bissell.com
When contacting BISSELL, have model number of cleaner available.
Please record your Model Number: ___________________
Please record your Purchase Date: ___________________
NOTE: Please keep your original sales receipt. It provides proof of purchase date in the event of
a warranty claim. See Warranty on page 20 for details.
Replacement parts - BISSELL vacuum
1
16
18
Item
Part No.
Part Name
1
2
3
4
5
303-1120
203-1297
203-1283
203-1073
203-6608
Style 7/9/10/12/14 Drive Belt (2-Pack)
Headlight Bulb
Wide Window Foot Brush Roll (gray)
Style 7/8/14 Pre-Motor Foam Filter
Style 8/14 HEPA Media POST-Motor Filter
2
www.bissell.com
ug110-4054_92L3_608.indd 18
3
4
5
800.237.7691
8/8/08 2:36:49 PM
Additional accessories
These items are available for purchase as accessories for your BISSELL PowerClean:
To purchase call 1-800-237-7691 or visit www.bissell.com.
1
Item
Part No.
Part Name
1
2
3
4
5
203-1056
203-1059
203-1429
203-1068
203-1216
Crevice Tool
Dusting Brush/Upholstery Tool
TurboBrush
Extension Wand
Twist 'n Snap Vacuum Hose (clear)
2
www.bissell.com
ug110-4054_92L3_608.indd 19
3
4
5
800.237.7691
16
19
8/8/08 2:36:54 PM
Warranty - BISSELL PowerClean
®
Vacuum
This warranty gives you specific legal rights, and you may also have other rights which may vary from state
to state. If you need additional instruction regarding this warranty or have questions regarding what it may
cover, please contact BISSELL Consumer Services by E-mail, telephone, or regular mail as described below.
Limited One Year Warranty
Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, upon receipt of the product BISSELL
Homecare, Inc. will repair or replace (with new or remanufactured components or products), at BISSELL’s
option, free of charge from the date of purchase by the original purchaser, for one year any defective or
malfunctioning part.
See information below on "If your BISSELL product should require service".
This warranty applies to product used for personal, and not commercial or rental service. This warranty does not
apply to fans or routine maintenance components such as filters, belts, or brushes. Damage or malfunction caused
by negligence, abuse, neglect, unauthorized repair, or any other use not in accordance with the User's Guide is
not covered.
If your BISSELL product should require service:
Contact BISSELL Consumer Services to locate a BISSELL Authorized Service Center in your area.
If you need information about repairs or replacement parts, or if you have questions about your warranty,
contact BISSELL Consumer Services.
Website or E-mail:
www.bissell.com
Use the “Customer Services” tab.
Or Call:
BISSELL Consumer Services
1-800-237-7691
Monday - Friday 8 a.m. - 10 p.m. ET
Saturday 9 a.m. - 8 p.m. ET
Or Write:
BISSELL Homecare, Inc.
PO Box 3606
Grand Rapids, MI 49501
ATTN: Consumer Services
BISSELL HOMECARE, INC. IS NOT LIABLE FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES OF ANY NATURE ASSOCIATED WITH THE
USE OF THIS PRODUCT. BISSELL’S LIABILITY WILL NOT EXCEED THE
PURCHASE PRICE OF THE PRODUCT.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you.
*EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER
ORAL OR WRITTEN. ANY IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION
OF LAW, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE ONE YEAR DURATION
FROM THE DATE OF PURCHASE AS DESCRIBED ABOVE.
©2008 BISSELL Homecare, Inc
Grand Rapids, Michigan
Some states do not allow limitations on how long an implied warranty last so the
All rights reserved. Printed in Korea
above limitation may not apply to you.
Part Number 110-4054
Rev 8/08
Visit our website at:
www.bissell.com
16
20
www.bissell.com
ug110-4054_92L3_608.indd 20
800.237.7691
8/8/08 2:36:57 PM