Instruction manual | Bissell 9400J Carpet Cleaner User Manual

Operations
VR-506
VR-505
VR-517
KRF-V6050D
KRF-V5050D
KRF-V5550D
Preparations
AUDIO VIDEO SURROUND RECEIVER
INSTRUCTION MANUAL
KENWOOD CORPORATION
Compared to standard remote controls, the remote control supplied with this receiver has several operation
modes. These modes enable the remote control to control other audio/video components. In order to
effectively use the remote control it is important to read the operating instructions and obtain a proper
understanding of the remote control and how to switch its operation modes (etc.).
Using the remote control without completely understanding its design and how to switch the operation modes
may result in incorrect operations.
B60-4942-10 03 MA (K, P, Y, M, X, I)
_4942-10 03 /01/EN
1
PR
0009
3/16/01, 10:15 AM
Additional Information
About the supplied remote control
Remote Control
This instruction manual is used to describe multiple models listed above.
Model availability and features (functions) may differ depending on the country and
sales area.
Before applying the power
Units are designed for operation as follows.
2
U.S.A. and Canada ........................................... AC 120 V only
Australia ........................................................... AC 240 V only
Europe and U.K. ............................................... AC 230 V only
China and Russia ............................................ AC 220 V only
*Other countries ........... AC 110-120 / 220-240 V switchable
Preparations
* AC voltage selection
Caution : Read this page carefully to ensure safe
operation.
Unpacking
Unpack the unit carefully and make sure that all accessories are put aside
so they will not be lost.
Examine the unit for any possibility of shipping damage. If your unit is
damaged or fails to operate, notify your dealer immediately. If your unit
was shipped to you directly, notify the shipping company without delay.
Only the consignee (the person or company receiving the unit) can file a
claim against the carrier for shipping damage.
We recommend that you retain the original carton and packing materials
for use should you transport or ship the unit in the future.
Keep this manual handy for future reference.
The AC voltage selector switch on the rear panel is set to the voltage that
prevails in the area to which the unit is shipped. Before connecting the
power cord to your AC outlet, make sure that the setting position of this
switch matches your line voltage. If not, it must be set to your voltage
in accordance with the following direction.
Accessories
AM loop antenna (1)
FM indoor antenna (1)
AC voltage selector switch
AC 220V 240V
Move switch lever to
match your line voltage
with a small screwdriver or other pointed
tool.
AC 110V 120V
For VR-506 and KRF-V6050D
Remote control unit (1)
RC-R0615
PLAY IN
REC OUT
Batteries (R6/AA) (2)
PLAY IN
L
MONITOR
OUT
DVD
VIDEO 1
VIDEO 1
R
R
B
L
75µs
AM 10kHz
FM 100kHz
50µs
AM 9kHz
FM 50kHz
R
A
R
L
L
C
DEEMPHASIS
CHANNEL
SPACE
Note:
Our warranty does not cover damage caused by excessive line voltage
due to improper setting of the AC voltage selector switch.
For VR-505 and KRF-V5050D
Remote control unit (1)
Batteries (R6/AA) (2)
RC-R0511
Safety precautions
WARNING :
TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION
For VR-517 and KRF-V5550D
Remote control unit (1)
Batteries (R6/AA) (2)
RC-R0617
*AC plug adaptor (1)
*Use to adapt the plug on the power
cord to the shape of the wall outlet.
(Accessory only for regions where use
is necessary.)
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL,
WITHIN AN EQUILATERAL TRIANGLE, IS INTENDED TO ALERT
THE USER TO THE PRESENCE OF UNINSULATED “DANGEROUS VOLTAGE” WITHIN THE PRODUCT’S ENCLOSURE
THAT MAY BE OF SUFFICIENT MAGNITUDE TO CONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS.
THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE USER TO THE PRESENCE OF IMPORTANT OPERATING AND MAINTENANCE
(SERVICING) INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE.
Microcomputer malfunction
If operation is not possible or an erroneous display appears, even though
all connections have been made properly, reset the microcomputer
referring to “In case of difficulty”.
·
Maintenance of the unit
When the front panel or case becomes dirty, wipe with a soft, dry
cloth. Do not use thinner, benzine, alcohol, etc. for these agents may
cause discoloration.
In regard to contact cleaner
Do not use contact cleaners because it could cause a malfunction.
Be specially careful not to use contact cleaners containing oil, for
they may deform the plastic component.
_4942/02-09/EN
2
3/16/01, 10:16 AM
Before applying the power
Contents
Caution : Read the pages marked
safe operation.
3
carefully to ensure
Before applying the power ................... 2
Safety precautions .............................................. 2
Unpacking .......................................................... 2
How to use this manual ...................................... 4
Special features .................................................. 4
Additional
Information
In case of difficulty ........................... 39
Specifications ................................. 41
Names and functions of parts ................ 5
Preparations
Preparations
Remote control unit (RC-R0615)
(VR-506/KRF-V6050D) ....................................... 6
Remote control unit (RC-R0511)
(VR-505/KRF-V5050D) ....................................... 7
Remote control unit (RC-R0617)
(VR-517/KRF-V5550D) ....................................... 8
Setting up the system ......................... 9
Connecting audio components ......................... 10
Connecting video components ......................... 11
Connecting a DVD player (6-channel input) ...... 12
Digital connections ........................................... 13
Connecting to the AV AUX jacks
(VR-506/517/KRF-V6050D only) ....................... 14
Connecting the antennas .................................. 14
Connecting the system control ......................... 15
Connecting the speakers .................................. 16
Preparing the remote control ............................ 18
Operations
Preparing for surround sound ............... 19
Speaker settings ............................................... 19
Recording ...................................... 22
Recording audio (analog sources) .................... 22
Recording video ................................................ 23
Recording audio (digital sources) ...................... 23
Operations
Operations
Listening to radio broadcasts ............... 23
Tuning radio stations ........................................ 23
Presetting radio stations manually .................... 24
Receiving preset stations .................................. 24
Receiving preset stations in order (P.CALL) ...... 24
Ambience effects .............................. 25
Surround modes ............................................... 25
Surround play ................................................... 27
DVD 6-channel playback
(VR-506/517/KRF-V6050D/V5050D) ................ 28
Convenient functions ........................................ 28
Basic remote control operations for other
components(For VR-506/517/KRF-V6050D/
V5550D) ........................................ 30
Remote Control
_4942/02-09/EN
Registering setup codes for other
components ...................................................... 30
Operating other components ............................ 30
Setup code chart .............................................. 31
DVD player operation keys
(For VR-505/KRF-V5050D) ............................... 32
Cassette deck, CD player & MD recorder
operations (For VR-505/KRF-V5050D) ............. 33
Cassette deck, CD player & MD recorder
operations (For VR-506/517/KRF-V6050D/
V5550D) ............................................................ 34
Other components’ operations (For VR-506/517/
KRF-V6050D/V5550D) ..................................... 36
3
For the U.S.A.
FCC WARNING
This equipment may generate or use radio frequency energy. Changes
or modifications to this equipment may cause harmful interference
unless the modifications are expressly approved in the instruction
manual. The user could lose the authority to operate this equipment if an
unauthorized change or modification is made.
NOTE:
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment may cause harmful
interference to radio communications, if it is not installed and used in
accordance with the instructions. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
– – Reorient or relocate the receiving antenna.
– – Increase the separation between the equipment and receiver.
– – Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
– – Consult the dealer or an experienced radio / TV technician for help.
Remote Control
Preparing for playback ...................................... 20
Listening to a source component ..................... 21
Adjusting the sound .......................................... 21
For the U.S.A.
Note to CATV system installer:
This reminder is provided to call the CATV system installer's attention to
Article 820-40 of the NEC that provides guidelines for proper grounding
and, in particular, specifies that the cable ground shall be connected to
the grounding system of the building, as close to the point of cable entry
as practical.
As an ENERGY STAR® Partner, Kenwood Corporation has determined that this product meets the
ENERGY STAR® guidelines for energy efficiency.
This product can save energy. Saving energy reduces air pollution and
lowers utility bills.
3/16/01, 10:16 AM
Additional Information
Normal playback .............................. 20
Before applying the power
4
How to use this manual
Special features
This manual covers the VR-506, VR-505, VR-517, KRF-V6050D, KRFV5050D and KRF-V5550D. Items such as functions, number of jacks, and
remote control details somewhat differ between these models. To confirm
the functions available on the model you have purchased, refer to the table
below.
Terminal
Front input
Preparations
Model name
Remote
Control
VR-506
KRF-V6050D
RC-R0615
2 systems
(A, B)
Equipped
VR-505
KRF-V5050D
RC-R0511
1 system
Not equipped
VR-517
KRF-V5550D
RC-R0617
1 system
Equipped
(except KRFV5550D)
Speaker out
True home theater sound
This receiver incorporates a wide variety of surround modes to bring you
maximum enjoyment from your video software. Select a surround mode
according to your equipment or the software you are going to play and
enjoy!
∞
Dolby Pro Logic & Dolby 3 Stereo
This surround system reproduces theater-like surround sound from
.
video software marked
The PRO LOGIC mode uses the built-in adaptive matrix circuit to steer
the Left, Center, Right and Surround channel audio signals.
The 3 STEREO mode will redirect the Surround signal to the front left
and right speakers when only the front and center speakers are used.
Dolby Digital
This manual is divided into four sections, Preparations, Operations,
Remote Control, and Additional Information.
The DOLBY DIGITAL mode lets you enjoy full digital surround from
software processed in the Dolby Digital format. Dolby Digital provides
up to 5.1 channels of independent digital audio for better sound quality
and more powerful presence than conventional Dolby Surround.
Preparations
DTS
Shows you how to connect your audio and video components to the
receiver and prepare the surround processor.
We will guide you to make setting up your system as easy as possible.
However, since this receiver works with all of your audio and video
components, connecting the system can be fairly complex.
Operations
Shows you how to operate the various functions available on the receiver.
Remote Control
(For VR-506/517/KRF-V6050D/V5550D only)
Shows you how to operate other components using the remote control,
as well as a detailed explanation of all remote control operations. Once
you have registered your components with the proper setup codes, you’ll
be able to operate both this receiver and your other AV components (TV,
VCR, DVD player, CD player, etc.) using the remote control supplied with
this receiver.
Additional Information
Shows you additional information such as “In case of difficulty” (troubleshooting) and “Specifications”.
Memory back up function
Please note that the following items will be deleted from the unit's
memory if the power cord is disconnected from the AC outlet for
approximately 2 days.
• Power mode.
• Input selector settings.
• Device preset.
• Picture output.
• Speaker ON/OFF
• Volume level.
• BASS, TREBLE, INPUT level.
• Subwoofer ON/OFF.
• Dimmer level.
• Monitor ON/OFF.
• MD/TAPE settings.
_4942/02-09/EN
• 6ch/2ch input setting.
• Listen mode setting.
• Speaker settings.
• Input mode setting.
• Midnight mode setting.
• Broadcast band.
• Frequency setting.
• Preset stations.
• Tuning mode.
• CINEMA EQ.
• Source Direct.
4
DTS (Digital Theater System) is a 5.1 channel digital audio format that
provides five full-spectrum channels and one low-frequency (subwoofer)
channel for unprecedented clarity, optimum channel separation and a
(wide) dynamic range.
In the DTS mode, the 5.1 channel digital input from a DTS CD, LD or
DVD disc (carrying the “DTS” marking) can be played in Digital Surround.
Important:
When a DTS disc is played on a CD, LD or DVD player, noise may be
output from the analog output. It is recommended that you connect the
digital output of the player to the digital input of this unit.
DSP surround modes
The DSP (Digital Signal Processor) used for this receiver incorporates
a variety of high quality adjustable sound fields, like “ARENA”, “JAZZ
CLUB”, THEATER”, STADIUM” and “DISCO”. It is compatible with
almost any kind of program source.
DVD 6-channel input
(For VR-506/517/KRF-V6050D/V5050D only)
If you own a DVD player equipped with 6-channel output, this receiver
allows you to obtain the full surround sound impact of DVD source
material featuring multi-channel encoding. Since the source signals are
digital and each channel is input independently, the resulting ambience
is far superior to what can be achieved with conventional surround
sound systems.
Universal IR (InfraRed) remote control
(Except for VR-505/KRF-V5050D)
In addition to the basic receiver, the remote control supplied with this
receiver can also operate almost all of your remote controllable audio and
video components. Just follow the simple setup procedure to register the
components you have connected.
3/16/01, 10:16 AM
Names and functions of parts
Frequency display,
Input display,
Preset channel display,
Surround mode display
Speaker indicator
AUTO SOUND indicator
PRO LOGIC
indicator
DIGITAL indicator
S.DIRECT indicator
AUTO indicator
AUTO
FM AUTO SOUND DIGITAL
MEMO indicator
5
Band indicators
MUTE indicator
SP
A B TI.VOL
CLIP
MUTE
RDS EON
PTY
TP
TA
NEWS
L
C
LFE
SL
R
AM PRO LOGIC S.DIRECT MEMO
MHz 3 STEREO MONITOR ST.
TUNED
kHz DOWNMIX
DSP
SW
S
SR
TUNED indicator
MONITOR indicator
DSP indicator
DOWNMIX indicator
Speaker selection indicators
Input channel indicators
Output channel indicators
ST. indicator
Preparations
CLIP indicator
3 STEREO indicator
STEREO indicator
Display
VOLUME CONTROL
STANDBY
STANDBY
DTS
POWER
SET UP
ON/STANDBY
ON/STANDBY
POWER
ON
For VR-506/
505/517
DOLBY
DIGITAL
INPUT MODE
DSP MODE
DIMMER
INPUT SELECTOR
MONITOR
SOUND
LISTEN MODE
SOURCE DIRECT
BAND
AUTO/CINEMA EQ.
MEMORY
MULTI CONTROL
OFF
A SPEAKERS B
DOWN
S-VIDEO
PHONES
SPEAKER
MUTE
1 POWER key
(
(For KRF-V6050D/V5050D/V5550D)
Use to turn the main power ON/OFF.
(
2 ON/STANDBY ( ) key
(For KRF-V6050D/V5050D/V5550D)
Use to switch the power ON/STANDBY when
the POWER is turned ON.
STANDBY indicator
2 POWER ( ) key
(
(For VR-506/505/517)
Use to turn the power ON/STANDBY.
STANDBY indicator
3 MULTI CONTROL keys
(
Use to control a variety of settings.
4 SET UP key
(
Use to select the speakers' settings etc.
5 Surround indicators
DTS indicator
¶
Lights when the receiver is in the DTS mode.
DOLBY DIGITAL indicator
¶
Lights when the receiver is in the Dolby Digital
mode.
DSP MODE indicator
¶
Lights up when the receiver is in DSP mode.
V
UP
AV AUX L – AUDIO – R
For VR-506/517/
KRF-V6050D
For VR-505/517/
KRF-V5050D/V5550D
6 INPUT MODE key
9
Use to switch between the digital and analog
inputs.
7 DIMMER key
£ª
Use to adjust the brightness of the display.
Use to select the REC MODE.
8 MONITOR key
™
Use to monitor the source that is connected to
the MONITOR jack.
9 VOLUME CONTROL knob
¡
0 PHONES jack
™
Use for headphone listening.
! SPEAKERS A/B keys
)
(For VR-506/KRF-V6050D)
Use to turn the A/B speakers ON/OFF.
! SPEAKER key
)
(For VR-505/517/KRF-V5050D/V5550D)
Use to turn the speaker ON/OFF.
MUTE key
™
(For VR-505/517/KRF-V5050D/V5550D)
Use to temporarily mute the sound.
@ SOUND key
•
Use to adjust the sound quality and ambience
effects.
# BAND key
£
Use to select the broadcast band.
$ AUTO/CINEMA EQ. key
£
Use to select the auto tuning mode.
Use to switch the status of CINEMA EQ.
% LISTEN MODE key
¶
Use to select the listening mode.
^ MEMORY key
¢
Use to store radio stations in the preset memory.
& SOURCE DIRECT key
™
Use to pass the source material direct to the
amplifier.
* INPUT SELECTOR knob
¡
Use to select the input sources.
( AV AUX (S VIDEO, V, AUDIO L/R) jacks
(For VR-506/517/KRF-V6050D)
$
Standby mode
When standby indicator is lit, this receiver is in standby mode and consumes a small amount of curent for back-up. This system can be switched on using
remote controls.
_4942/02-09/EN
5
3/16/01, 10:16 AM
Names and functions of parts
6
Remote control unit (RC-R0615) (VR-506/KRF-V6050D)
This remote control unit can be used not only for Kenwood products but also for other non-Kenwood products
by setting the appropriate maker setup codes.
⁄
POWER
Preparations
1
1
2
#
3
TV
4
5
6
7
8
9
0
+10
RETURN
LSTN M.
MENU
SET UP
OSD
SOUND
$
VCR
2
3
4
7
8
9
0
!
CABLE
DSS
POWER
P.CALL
P.CALL
5
6
DVD
MULTI CONTROL
TUNING
B.BOOST
RECEIVER
TITLE
PHONO
A/B+100
DISC SKIP
AUTO
TV SEL.
CD/DVD
INPUT SEL.
TUNER
DVD
VIDEO1
ENTER
VIDEO2
DVD
DISC SEL.
CINE.EQ
@
MUTE
1 Numeric keys
fi
Provide functions identical to those of the
original remote control supplied with the
component you are controlling.
2 LSTN M. key
¶
Use to select the listening mode.
RETURN key
Use to operate other components.
3 SET UP key
(
Use to select the speakers' settings etc.
MENU key
Use to operate other components.
4 SOUND key
¡
Use to adjust the sound quality and ambience effects.
OSD key
Use to operate other components.
5 MULTI CONTROL keys
(
Use to control a variety of settings.
Use to operate other components.
P.CALL 4/¢ keys
¢
If tuner is selected as the input source, these
keys function as P.CALL keys.
4/¢ keys
If CD or MD is selected as the input source,
these keys function as skip keys.
6 TUNING 1/¡ keys
Use to operate the tuner or selected component.
If CD, MD or TAPE is selected as the input
source, these keys function as search keys.
_4942/02-09/EN
6
BAND
VOLUME
MD/TAPE
%
^
&
*
(
)
If the name of a function is different on
the receiver and on the remote control,
the name of the remote control key in
this manual is indicated in parentheses.
CHANNEL
AV AUX
¡
™
7 B.BOOST key
¡
Use to select the maximum adjustment setting for the low frequency range.
RECEIVER key
Use to return to the operation of the receiver.
8 DISC SKIP key
If CD is selected as the input source, this key
functions as the multi-CD player disc skip key.
A/B key
If TAPE is selected as the input source, this
(A and B) of a double cassette deck.
+100 key
Use to select the disc number with the multiCD player.
9 TITLE key
Use to operate other components.
0 TV SEL. key
Use to operate other components.
! INPUT SELECTOR keys (DVD, PHONO,
CD/DVD, TUNER, MD/TAPE, VIDEO1,
VIDEO2, AV AUX)
¡
Use to select the input sources.
4 DVD ¢ keys
When in DVD player operations, these keys
function as skip keys.
@ MUTE key
™
Use to temporarily mute the sound.
*
# POWER ( ) key
Use to turn the receiver on and off.
$ POWER key (TV, VCR, DVD, DSS,
CABLE)
Use to turn the other components on and off.
% ENTER key
Use to select the input sources.
2 key
If tape is selected as the input source, this
key functions as the play key for side B of the
cassette (the side facing away from the front
of the deck).
^ BAND key
Use to select the broadcast band.
6 key
If CD is selected as the input source, this key
functions as the play/pause key.
If MD or TAPE is selected as the input
source, this key functions as the play key.
& AUTO key
£
Use to select the auto tuning mode.
7 key
If CD, MD or TAPE is selected as the input
source, this key functions as the stop key.
* 8 key
Use to operate other components.
( INPUT SEL. key
Use to operate other components.
) CHANNEL %¥fi key
Use to select the channel.
¡ CINE.EQ key
Use to switch the status of CINEMA EQ.
DISC SEL. key
Use to operate other components.
™ VOLUME keys
¡
Use to adjust the receiver volume.
3/16/01, 10:17 AM
Names and functions of parts
Remote control unit (RC-R0511) (VR-505/KRF-V5050D)
7
POWER
2
3
4
5
6
7
8
9
0
2
3
MENU
SET UP
6
7
8
@
RECEIVER
OSD RETURN TITLE
SOUND LISTEN MODE
P.CALL
P.CALL
TUNING
A/B+100
BASS BOOST DISC SKIP
PHONO/AUX
CD/DVD
ENTER
AUTO
TUNER
BAND
DVD
MD/TAPE
DVD
DISC SEL.
VIDEO1 VIDEO2 CINE.EQ
MUTE
_4942/02-09/EN
7
#
$
MULTI CONTROL
9
1 Numeric keys
¢
If CD or MD is selected as the input source,
these keys function as numeric keys. If tuner
is selected as the input source, these keys
are used to call up station presets.
2 SET UP key
(
Use to select the speakers' settings etc.
MENU key
Use to operate other components.
3 SOUND key
¡
Use to adjust the sound quality and ambience effects.
OSD key
Use to operate other components.
4 MULTI CONTROL keys
(
Use to control a variety of settings.
P.CALL 4/¢ keys
¢
If tuner is selected as the input source, these
keys function as P.CALL keys.
4/¢ keys
If CD or MD is selected as the input source,
these keys function as skip keys.
5 TUNING 1/¡ keys
If tuner is selected as the input source, these
keys function as tuning keys.
If CD, MD or TAPE is selected as the input
source, these keys function as search keys.
6 BASS BOOST key
¡
Use to select the maximum adjustment setting for the low frequency range.
!
POWER
+10
4
5
0
DVD
VOLUME
7 DISC SKIP key
If CD is selected as the input source, this key
functions as the multi-CD player disc skip key.
A/B key
If TAPE is selected as the input source, this
(A and B) of a double cassette deck.
+100 key
Use to select the disc number with the multiCD player.
8 INPUT SELECTOR keys (DVD, PHONO/
AUX, CD/DVD, TUNER, MD/TAPE,
VIDEO1, VIDEO2)
¡
Use to select the input sources.
4 DVD ¢ keys
When in DVD player operations, these keys
function as skip keys.
9 MUTE key
™
Use to temporarily mute the sound.
*
0 POWER ( ) key
Use to turn the receiver on and off.
! DVD POWER key
›
Used to operate DVD player.
For details, refer to the instruction manual of
your DVD player. (Press the DVD POWER
key for more than 2 seconds.)
@ RECEIVER key
Use to return to the operation of the receiver.
# TITLE key
Use to operate other components.
%
^
&
*
(
)
$ LISTEN MODE key
¶
Use to select the listening mode.
RETURN key
Use to operate other components.
% ENTER key
Use to operate other components.
2 key
If tape is selected as the input source, this key
functions as the play key for side B of the
cassette (the side facing away from the front of
the deck).
^ BAND key
£
Use to select the broadcast band.
6 key
If CD is selected as the input source, this key
functions as the play/pause key.
If MD or TAPE is selected as the input source,
this key functions as the play key.
& 8 key
Use to operate other components.
* AUTO key
£
Use to select the auto tuning mode.
7 key
If CD, MD or TAPE is selected as the input source,
this key functions as the stop key.
( CINE.EQ key
Use to switch the status of CINEMA EQ.
DISC SEL. key
Use to operate other components.
) VOLUME keys
¡
Use to adjust the receiver volume.
3/16/01, 10:17 AM
Preparations
1
1
Names and functions of parts
8
Remote control unit (RC-R0617) (VR-517/KRF-V5550D)
This remote control unit can be used not only for Kenwood products but also for other non-Kenwood products
by setting the appropriate maker setup codes.
⁄
POWER
Preparations
1
1
2
#
3
TV
4
5
6
7
8
9
0
+10
RETURN
LSTN M.
MENU
SET UP
OSD
SOUND
$
VCR
2
3
4
7
8
9
0
!
CABLE
DSS
POWER
P.CALL
P.CALL
5
6
DVD
MULTI CONTROL
TUNING
B.BOOST
RECEIVER
TITLE
AUX
A/B+100
DISC SKIP
AUTO
TV SEL.
CD/DVD
INPUT SEL.
TUNER
DVD
VIDEO1
ENTER
VIDEO2
DVD
DISC SEL.
CINE.EQ
@
MUTE
1 Numeric keys
fi
Provide functions identical to those of the
original remote control supplied with the
component you are controlling.
2 LSTN M. key
¶
Use to select the listening mode.
RETURN key
Use to operate other components.
3 SET UP key
(
Use to select the speakers' settings etc.
MENU key
Use to operate other components.
4 SOUND key
¡
Use to adjust the sound quality and ambience effects.
OSD key
Use to operate other components.
5 MULTI CONTROL keys
(
Use to control a variety of settings.
Use to operate other components.
P.CALL 4/¢ keys
¢
If tuner is selected as the input source, these
keys function as P.CALL keys.
4/¢ keys
If CD or MD is selected as the input source,
these keys function as skip keys.
6 TUNING 1/¡ keys
Use to operate the tuner or selected component.
If CD, MD or TAPE is selected as the input
source, these keys function as search keys.
_4942/02-09/EN
8
BAND
VOLUME
MD/TAPE
%
^
&
*
(
)
If the name of a function is different on
the receiver and on the remote control,
the name of the remote control key in
this manual is indicated in parentheses.
CHANNEL
AV AUX
¡
™
7 B.BOOST key
¡
Use to select the maximum adjustment setting for the low frequency range.
RECEIVER key
Use to return to the operation of the receiver.
8 DISC SKIP key
If CD is selected as the input source, this key
functions as the multi-CD player disc skip key.
A/B key
If TAPE is selected as the input source, this
(A and B) of a double cassette deck.
+100 key
Use to select the disc number with the multiCD player.
9 TITLE key
Use to operate other components.
0 TV SEL. key
Use to operate other components.
! INPUT SELECTOR keys (DVD, AUX, CD/
DVD, TUNER, MD/TAPE, VIDEO1,
VIDEO2, AV AUX)
¡
Use to select the input sources.
4 DVD ¢ keys
When in DVD player operations, these keys
function as skip keys.
@ MUTE key
™
Use to temporarily mute the sound.
*
# POWER ( ) key
Use to turn the receiver on and off.
$ POWER key (TV, VCR, DVD, DSS,
CABLE)
Use to turn the other components on and off.
% ENTER key
Use to operate other components.
2 key
If tape is selected as the input source, this
key functions as the play key for side B of the
cassette (the side facing away from the front
of the deck).
^ BAND key
£
Use to select the broadcast band.
6 key
If CD is selected as the input source, this key
functions as the play/pause key.
If MD or TAPE is selected as the input
source, this key functions as the play key.
& AUTO key
£
Use to select the auto tuning mode.
7 key
If CD, MD or TAPE is selected as the input
source, this key functions as the stop key.
* 8 key
Use to operate other components.
( INPUT SEL. key
Use to operate other components.
) CHANNEL %¥fi key
Use to select the channel.
¡ CINE.EQ key
Use to switch the status of CINEMA EQ.
DISC SEL. key
Use to operate other components.
™ VOLUME keys
¡
Use to adjust the receiver volume.
3/16/01, 10:17 AM
Setting up the system
DTS disclaimer clause
DTS Digital Surround™ is a discrete 5.1 channel digital audio format
available on CD, LD, and DVD software which consequently cannot be
decoded and played back inside most CD, LD, or DVD players. For this
reason, when DTS-encoded software is played back through the analog
outputs of the CD, LD, or DVD player, excessive noise will be exhibited.
To avoid possible damage to the audio system, proper precautions
should be taken by the consumer if the analog outputs are connected
directly to an amplification system. To enjoy DTS Digital Surround™
playback, an external 5.1 channel DTS Digital Surround™ decoder
system must be connected to the digital output (S/P DIF, AES/EBU, or
TosLink) of the CD, LD or DVD player.
Input mode settings
CD/DVD, VIDEO2 and DVD/6ch or DVD (VR-505/KRF-V5550D only)
inputs each include jacks for digital audio input and analog audio input.
You must select beforehand which type of input is to be used for each
connected component.
The initial factory settings for audio signal playback (CD/DVD,DVD/
6ch or DVD (VR-505/KRF-V5550D only)) and (VIDEO2) are digital
and analog respectively.
To use the analog audio input for playback instead (if, for example, you
have connected a VCR to the VIDEO2 input), you must set the input
mode for the corresponding input to the analog mode.
After completing connections and turning on the receiver, follow the
steps below.
INPUT SELECTOR
VIDEO 2/MONITOR jacks
The receiver’s VIDEO 2/MONITOR jacks can be used in two different
ways. Make the appropriate setting for the component connected to the
jack when the receiver is turned on.
Use as a VIDEO 2 jack
You can connect a video deck or the like to these jacks and perform
video playback and recording. The initial factory setting is “VIDEO 2”.
Use as a MONITOR jack
You can connect a cassette deck or the like to these jacks and make use
of the deck’s monitoring function during recording. Alternately, you can
connect a graphic equalizer to these jacks to apply compensation to the
music signal.
To use the VIDEO 2/MONITOR jacks as a MONITOR jack, hold down
the MONITOR key of the main unit for more than two seconds so that
the display below appears.
INPUT MODE
1 Use the INPUT SELECTOR knob to select CD/DVD, VIDEO2,
DVD/6ch or DVD (VR-505/KRF-V5550D only).
2 Press the INPUT MODE key.
Each press switches the setting as follows:
In DTS play mode
1 D-AUTO (digital input, auto sound)
2 D-MANUAL (digital input, manual sound)
In DVD/6ch or DVD play mode
1 D-AUTO (digital input, auto sound)
2 D-MANUAL (digital input, manual sound)
3 6ch INPT (DVD/6ch input)(except for VR-505/KRF-V5550D)
4 ANALOG (analog input, manual sound)
MONITOR
In modes other than DTS or DVD play mode
1 D-AUTO (digital input, auto sound)
2 D-MANUAL (digital input, manual sound)
3 ANALOG (analog input, manual sound)
SP
A B TI.VOL
CLIP
MUTE
RDS EON PTY
TP
TA
NEWS
L
C
LFE
AUTO
FM AUTO SOUND DIGITAL
AM PRO LOGIC S.DIRECT MEMO
MHz 3 STEREO MONITOR ST.
TUNED
kHz DOWN MIX
DSP
R
SW
S
To switch the setting back to “VIDEO 2,” once again hold down the
MONITOR key for more than two seconds.
Notes
1. Be sure to insert all connection cords securely. If their connections are
imperfect, the sound may not be produced or noise may interfere.
2. Be sure to remove the power cord from the AC outlet before plugging or
unplugging any connection cords. Plugging/unplugging connection cords
without disconnecting the power cord can cause malfunctions and may
damage the unit.
3. Do not connect power cords from components whose power consumption is larger than what is indicated on the AC outlet at the rear of this unit.
Analog connections
Audio connections are made using RCA pin cords. These cables transfer
stereo audio signal in an “analog” form. This means the audio signal
corresponds to the actual audio of two channels. These cables usually have
2 plugs each end, one red for the right channel and one white for the left
channel. These cables are usually packed together with the source unit, or
are available at your local electronics retailer.
_4942/02-09/EN
9
Digital input:
Select this setting to play digital signals from a DVD, CD, or LD player.
Analog input:
Select this setting to play analog signals from a cassette deck, VCR,
or record player.
Auto sound:
In the auto sound mode (AUTO SOUND indicator lights), the receiver
selects the listening mode automatically during playback to match the
type of input signal (Dolby Digital, PCM, DTS ) and the speaker setting.
The initial factory setting is auto sound on.
To keep the receiver set to the currently selected listening mode, use
the INPUT MODE key to select “D-MANUAL” (manual sound).
However, even when this setting is selected, there may be cases in
which the listening mode is selected automatically to match a Dolby
Digital source signal depending on the combination of listening mode
and source signal.
If the INPUT MODE key is pressed quickly, sound may not be
produced.
3/16/01, 10:17 AM
9
Preparations
Make connections as shown in the following pages.
When connecting the related system components, be sure
to also refer to the instruction manuals supplied with the
components you are connecting.
Do not connect the power cord to a wall outlet until all
connections are completed.
Setting up the system
10
Connecting audio components
Shape of AC outlets
U.S.A. and Canada
Australia
Preparations
Other countries
SYSTEM CONTROL
jacks
%
PLAY IN
MONITOR
OUT
DVD
REC OUT
VIDEO 1
PLAY IN
VIDEO 1
R
R
B
L
75µs
AM 10kHz
FM 100kHz
50µs
AM 9kHz
FM 50kHz
R
A
R
L
To AC wall outlet
L
C
DEEMPHASIS
CHANNEL
SPACE
L
R
GND
PHONO
CD/DVD
REC OUT PLAY IN
MD/TAPE
AUDIO
REC OUT PLAY IN
VIDEO2/MONITOR
IN
OUT
Video component,
3 head cassette deck, or
Graphic equalizer ™
OUT
Cassette deck or
MD recorder
L
IN
R
AUX
(For VR-505/517/KRF-V5550D)
OUT
CD or DVD player
Moving coil (MC) cartridge
record player cannot be used
directly from the receiver unit. It
can only be used when another
equalizer amplifier is connected.
OUT
Record player
When you connect the audio cord of the video component to the VIDEO 2/MONITOR jacks, connect the video cord (yellow RCA pin cords)
of the connected component to the VIDEO 2 IN jack.
_4942/10-19/EN
10
3/16/01, 3:04 PM
Setting up the system
Connecting video components
11
About the S VIDEO
jacks
S Video jacks
(VR-506/517/KRF-V6050D)
PLAY IN
MONITOR
OUT
DVD
REC OUT
S VIDEO
PLAY IN
VIDEO 1
VIDEO 1
Use the S VIDEO jacks to
make connections to
video components with S
VIDEO IN/OUT jacks.
PLAY IN
REC OUT
PLAY IN
÷ If you use the S VIDEO
jacks to connect your video
playback components, be
sure to use the S VIDEO
jacks when connecting
your monitor and video
recording components.
L
MONITOR
OUT
DVD
VIDEO 1
VIDEO 1
R
R
B
L
75µs
AM 10kHz
FM 100kHz
50µs
AM 9kHz
FM 50kHz
R
A
R
L
L
C
DEEMPHASIS
CHANNEL
SPACE
VIDEO
VIDEO 2 IN
CD/DVD IN
DVD
MONITOR
OUT
VIDEO 1
OUT
CD / DVD
REC OUT PLAY IN
MD / TAPE
AUDIO
REC OUT PLAY IN
VIDEO 2/MONITOR
REC OUT PLAY IN
VIDEO 1
VIDEO 1 IN
Monitor TV
VIDEO
IN
IN
Video inputs
(Yellow RCA pin cords)
Video deck
IN
IN
OUT
Video inputs and
outputs
(Yellow RCA pin cords)
OUT
OUT
Audio inputs
and outputs
DVD player or LD player
OUT
A video component with digital audio outputs should be connected to the VIDEO2 jacks.
_4942/10-19/EN
11
3/16/01, 3:04 PM
Preparations
S VIDEO
Setting up the system
Connecting a DVD player (6-channel input)
12
If you have connected a DVD player to the receiver with digital connection, be sure to read the “Input
mode settings” section carefully.
9
PLAY IN
MONITOR
OUT
DVD
REC OUT
VIDEO 1
PLAY IN
PLAY IN
VIDEO 1
VIDEO 2
PLAY IN
VIDEO 3
R
R
B
L
Preparations
75µs
AM 10kHz
FM 100kHz
50µs
AM 9kHz
FM 50kHz
R
A
R
L
L
C
DEEMPHASIS
CHANNEL
SPACE
(Except for VR-505/KRF-V5550D)
VIDEO
VIDEO 2 IN
MONITOR
OUT
L
CD/DVD IN
DVD
CENTER
PLAY IN
DVD
DVD
VIDEO 1
OUT
R
FRONT
SURROUND
SUB
WOOFER
VIDEO 2/MONITOR
COAXIAL
DVD/6CH. INPUT
VIDEO 1 IN
S VIDEO cord
FRONT
OUT L/R
VIDEO OUT
(Yellow RCA
pin cord)
SURROUND
OUT L/R
DVD player
CENTER OUT
SUBWOOFER OUT
COAXIAL
DIGITAL
OUT
(AUDIO)
S VIDEO
OUT
To switch the speakers off , press the MUTE key.
CAUTION (Except for U.S.A. and Canada)
Be sure to adhere followings. Or proper ventilation will be blocked causing damage or fire hazard.
• Do not place any objects impairing heat radiation onto the top of unit.
• Leave a space around the unit (from the largest outside dimension including projection) equal or greater than, shown below.
Top panel : 50 cm
Side panel : 10 cm
Back panel : 10 cm
CAUTION (For U.S.A. and Canada)
Be sure to adhere followings. Or proper ventilation will be blocked causing damage or fire hazard.
• Do not place any objects impairing heat radiation onto the top of unit.
_4942/10-19/EN
12
3/16/01, 3:04 PM
Setting up the system
Digital connections
13
PLAY IN
REC OUT
Preparations
The digital in jacks can accept DTS, Dolby Digital, or PCM signals. Connect components capable
of outputting DTS, Dolby Digital, or standard PCM (CD) format digital signals.
If you have connected any digital components to the receiver, be sure to read the “Input mode
settings” section carefully.
9
PLAY IN
L
MONITOR
OUT
DVD
VIDEO 1
VIDEO 1
R
R
B
L
75µs
AM 10kHz
FM 100kHz
50µs
AM 9kHz
FM 50kHz
R
A
R
L
L
C
DEEMPHASIS
CHANNEL
SPACE
DVD
VIDEO 2/MONITOR
COAXIAL
CD/DVD
OPTICAL
DIGITAL IN
Optical fiber
cable
OPTICAL DIGITAL OUT (AUDIO)
CD player
COAXIAL
DIGITAL
OUT
(AUDIO)
COAXIAL DIGITAL OUT (AUDIO)
Component with a DTS, Dolby
Digital, or PCM COAXIAL
DIGITAL OUT
RF digital
demodulator
(DEM-9991D)
(sold separately)
Connect the video signal and analog
audio signals to the VIDEO 2 jacks.
(See “Connecting video components”.)
!
DOLBY DIGITAL RF
OUT (AUDIO)
PCM OUT
LD player
To connect an LD player with a DIGITAL RF OUT, connect the LD player to the KENWOOD RF digital demodulator (DEM-9991D).
Next, connect the DIGITAL OUT jacks of the demodulator to the DIGITAL IN jacks of the receiver.
Connect the video signal and analog audio signals to the VIDEO 2/MONITOR jacks. (See “Connecting video components”.)
_4942/10-19/EN
13
3/16/01, 3:04 PM
Setting up the system
14
Connecting to the AV AUX jacks
(VR-506/517/KRF-V6050D only)
Connecting the antennas
AM loop antenna
The AV AUX jacks are convenient for connection of video components
such as a camcorder or a video game.
The supplied loop antenna is for use indoors. Place it as far as possible from
the receiver, TV set, speaker cords and power cord, and adjust the direction
for best reception.
AM antenna terminal connections
1 Push lever.
2 Insert cord.
3 Release lever.
Preparations
FM indoor antenna
S VIDEO
V
The supplied indoor antenna is for temporary use only. For stable signal
reception we recommend using an outdoor antenna. Disconnect the indoor
antenna when you connect one outdoors.
AV AUX L — AUDIO — R
FM antenna terminal connections
Insert cord.
S VIDEO cord
FM outdoor antenna
Lead the 75Ω coaxial cable connected to the FM outdoor antenna into the
room and connect it to the FM 75Ω terminal.
PLAY IN
MONITOR
OUT
DVD
REC OUT
VIDEO 1
PLAY IN
VIDEO 1
R
R
B
L
75µs
AM 10kHz
FM 100kHz
50µs
AM 9kHz
FM 50kHz
VIDEO OUT
Camcorder, other VCR,
video game, digital camera,
S VIDEO OUT
or portable MD player
R
A
R
L
L
C
DEEMPHASIS
CHANNEL
SPACE
Attach to the stand.
AUDIO OUT
ANTENNA
GND
FM
75Ω
AM
AM loop antenna
FM indoor antenna
FM outdoor antenna
• To select the source connected to the AV AUX jacks, select AV
AUX by using the INPUT SELECTOR knob.
¡
• When you connect the audio source such as the MD player, you
do not need to connect the video cable.
• When you connect the unit and the component with the S
VIDEO cord, you can get better picture quality.
_4942/10-19/EN
14
Use an antenna
adaptor
(Commercially
available)
3/16/01, 3:04 PM
Setting up the system
Connecting the system control
15
This unit is compatible only with the [SL-16] mode. The system
control operation is not available if the unit is connected in the
[XS8], [XS], or [XR] connection mode.
If your component has the mode select switch, set the connected
components to the [SL16] mode.
SYSTEM CONTROL OPERATIONS
Remote Control
Lets you operate this unit with the system remote supplied with the
receiver.
Automatic Operation
When you start playback from a source component, the input selector
on this unit switches to that component automatically.
Synchronized Recording
Lets you synchronize recording with the start of playback when recording from CD, MD or analog discs.
SYSTEM
CONTROL
SYSTEM CONTROL
cord
• You may connect the system control cord to either the left or right jack.
EXAMPLE: [SL16] mode connections
The underlined portion represents the setting of the system control
mode.
[SL16]
Receiver
[SL16] [XS] [XS8] [XR]
Cassette deck
or MD recorder
[SL16] [XS] [XS8]
CD player
[XS]
Record player
SYSTEM
CONTROL
cord
Registering setup codes for KENWOOD audio components
(VR-506/517/KRF-V6050D/V5550D)
• If you own remote controllable KENWOOD audio components that are
not compatible with system control, registering the setup code enables you to control those components using the remote control
supplied with this unit (without connecting system control cords). To
register setup codes for your remote controllable KENWOOD audio
components, see “Registering setup codes for other components”.
º
• In order to take advantage of the system control operations, the
components must be connected to the correct jacks. To use a CD
player it must be connected to the CD jacks. To use a cassette deck
(or MD recorder) it must be connected to the MD/TAPE jacks. When
using more than one CD player (etc.) only the one connected to the
specified jacks may be connected for system control.
• Some CD players and cassette decks are not compatible with the
[SL16] system control mode. Do not make system connections with
equipment that is not [SL16] compatible.
• Some MD players are not system control compatible. You cannot
make system control connections to this kind of equipment.
Notes
1. [SL16] equipment cannot be combined with [XR], [XS], and [XS8]
equipment for system operations. If your equipment consists of this
kind of combination, please do not connect any system control cords.
Even without system control cords, normal operations can be carried
out without effecting performance.
2. Do not connect system control cords to any components other than
those specified by KENWOOD. It may cause a malfunction and
damage your equipment.
3. Be sure the system control plugs are inserted all the way in to the
system control terminals.
Do not connect a system control cord to a cassette deck connected
to the VIDEO2/MONITOR jacks.
_4942/10-19/EN
15
3/16/01, 3:04 PM
Preparations
Connecting system control cords after connecting a KENWOOD
audio component system lets you take advantage of convenient
system control operations.
Setting up the system
16
Connecting the speakers
1 Strip coating.
2 Loosen.
Connection of banana plugs (For U.S.A. and Canada)
1 Secure.
Preparations
3 Insert.
4 Secure.
2 Insert.
• Sound will not be heard if the speaker terminal is not fully secured.
• Never short circuit the + and – speaker cords.
• If the left and right speakers are connected inversely or the speaker
cords are connected with reversed polarity, the sound will be unnatural with ambiguous acoustic imaging. Be sure to connect the speakers correctly.
1 Strip coating.
2 Push the lever.
Speaker impedance
After confirming the speaker impedance indications printed on the rear
panel of the receiver, connect speakers with matching impedance
ratings. Using speakers with a rated impedance other than that indicated on the rear panel of the receiver could result in malfunctions or
damage to the speakers or receiver.
3 Insert the cord.
_4942/10-19/EN
4 Return the lever.
16
3/16/01, 3:04 PM
Setting up the system
Connecting the speakers
17
Front Speakers A
Right
Left
The VR-505/517/KRF-V5050D/V5550D are equipped with one-touch
speaker terminals.They are arranged in the same manner as the speaker
terminals of the VR-506/KRF-V6050D. Refer to the instructions on
making connections to the VR-506/KRF-V6050D when making connections to the VR-505/517/KRF-V5050D/V5550D.
FRONT
SPEAKERS
FRONT SPEAKERS
RED
CENTER
SPEAKER
FRONT SPEAKERS
RED
BLUE
CENTER SPEAKER
GREEN
CENTER SPEAKER
BLUE
GREEN
+
+
-
-
+
-
RED
BLUE
GREEN
VR-517/KRF-V5550D
VR-506/KRF-V6050D
PLAY IN
REC OUT
VR-505/KRF-V5050D
VR-517/KRF-V5550D
SUB WOOFER
SPEAKER
(8 — 16Ω)
PLAY IN
SURROUND
SPEAKERS
(8 — 16Ω)
L
MONITOR
OUT
DVD
VIDEO 1
VIDEO 1
R
R
B
+
L
75µs
AM 10kHz
FM 100kHz
-
50µs
AM 9kHz
FM 50kHz
R
A
R
L
L
C
DEEMPHASIS
CHANNEL
SPACE
SW
BROWN
VR-506/KRF-V6050D
SUB WOOFER
PRE OUT
FRONT SPEAKERS
ORANGE
Powered
subwoofer
SURROUND SPEAKERS
(8 — 16Ω)
+
+
ORANGE
GRAY
GRAY
SURROUND SPEAKERS
Left
Surround Speakers
(Be sure to connect both
surround speakers)
Use the FRONT SPEAKERS
B terminals if you want to
connect a second front
speaker system (for VR-506/
KRF-V6050D).
17
GRAY
VR-505/KRF-V5050D
Right
(Except
VR-517/
KRF-V5550D)
_4942/10-19/EN
ORANGE
3/16/01, 3:04 PM
Preparations
Center
Speaker
Setting up the system
Preparing the remote control
18
Speaker placement
Loading the batteries
1 Remove the cover.
2 Insert the batteries.
Center speaker
Preparations
3 Close the cover.
1
2
Subwoofer
Front
speaker
Listening
position
Surround
speaker
• Insert two AA-size (R6) batteries as indicated by the polarity markings.
Operation
Front speakers : Place to the front left and right of the listening position.
Front speakers are required for all surround modes.
Center speaker : Place front and center. This speaker stabilizes the
sound image and helps recreate sound motion. Be sure to connect a
center speaker when using the Dolby 3 Stereo mode.
Surround speakers : Place to the direct left and right, or slightly
behind, the listening position at even heights, approximately 1 meter
above the ears of the listeners. These speakers recreate sound motion
and atmosphere. Required for surround playback.
Subwoofer : Reproduces powerful deep bass sounds.
When the STANDBY indicator is lit, the power turns ON when you press
the POWER key on the remote control. When the power comes ON,
press the key you want to operate.
Operating range
(Approx.)
Remote sensor
6m
• Although the ideal surround system consists of all the speakers listed
above, if you don't have a center speaker or a subwoofer, you can
divide those signals between the available speakers in the speaker
settings steps to obtain the best possible surround reproduction from
the speakers you have available.
(
Infrared ray system
Channel space switching
(Except for the USA, Canada, UK, Europe, and Australia)
The space between radio channels has been set to the one that prevails
in the area to which the system is shipped. However, if the current
channel space setting does not match the setting in the area where the
system is to be used, for instance when you move from area 1 or area
2 shown in the following table or vice versa, proper reception of AM/FM
broadcasts cannot be expected. In this case, change the channel space
setting in accordance with your area by referring to the following table.
CHANNEL
Space Frequency
Area
1
USA, Canada and South
American countries
FM: 100 kHz
AM: 10 kHz
2
Other countries
FM: 50 kHz
AM: 9 kHz
PLAY IN
MONITOR
OUT
DVD
REC OUT
VIDEO 1
• When pressing more than one remote control key successively, press
the keys securely by leaving an interval of 1 second or more between
keys.
Notes
1. The supplied batteries may have shorter lives than ordinary batteries due
to use during operation checks.
2. When the remote-controllable distance gets shorter than before, replace
both batteries with new ones.
3. Placing the remote sensor in direct sunlight, or in direct light from a high
frequency fluorescent lamp may cause a malfunction.
In such a case, change the location of the system installation to prevent
malfunction.
PLAY IN
VIDEO 1
R
75µs
AM 10kHz
FM 100kHz
50µs
AM 9kHz
FM 50kHz
DEEMPHASIS
CHANNEL
SPACE
R
A
DEEMPHASIS
CHANNEL
SPACE
Move switch lever to match your area with a small screwdriver or
other pointed tool.
_4942/10-19/EN
18
3/16/01, 3:05 PM
Preparing for surround sound
6 Use the MULTI CONTROL keys to select the appropriate center
speaker setting.
To enable you to obtain optimum enjoyment from the receiver’s listening
modes, make sure to complete the speaker settings (subwoofer, front,
center, and surround speakers) as described below.
MULTI CONTROL
SET UP
If you have selected “NML” as the front speakers setting,
1 CNTR ON: Center speaker setting mode to the receiver is
ON.
2 CNTR OFF: Center speaker setting mode to the receiver is
OFF.
POWER
7 Press the SET UP key again to accept the setting.
• The surround speaker setting indication (SURR) appears.
ON/STANDBY
(KRF-V6050D/
V5050D/
V5550D)
8 Use the MULTI CONTROL keys to select the appropriate surround
speaker setting.
SET UP
MULTI
CONTROL
RC-R0511
RC-R0615/R0617
1 Turn on the power to this receiver by pressing POWER
or ON/STANDBY key(s).
2 Select a speaker system.
1 Press the SET UP key such that the subwoofer setting
indication (SUBW ON) appears.
SP
A B TI.VOL
CLIP
MUTE
RDS EON
PTY
TP
TA
NEWS
L
C
LFE
LS
FM AUTO SOUND DIGITAL
AUTO
AM PRO LOGIC S.DIRECT MEMO
MHz 3 STEREO MONITOR ST.
TUNED
kHz DOWN MIX
DSP
R
SW
S
RS
2 Use the MULTI CONTROL keys to select the appropriate
subwoofer setting.
1 SUBW ON: Subwoofer setting mode to the receiver is ON.
2 SUBW OFF: Subwoofer setting mode to the receiver is OFF.
• The initial setting is “SUBW ON”.
• When the setting “SUBW OFF” is selected, the front speakers are
automatically set to “FRNT LRG” and the procedure skips to step 5.
• When subwoofer output sound is required, select “FRNT NML”.
3 Press the SET UP key to accept the setting.
• The front speakers setting indication (FRNT) appears.
SP
A B TI.VOL
CLIP
MUTE
RDS EON
PTY
TP
TA
NEWS
L
C
LFE
LS
FM AUTO SOUND DIGITAL
AUTO
AM PRO LOGIC S.DIRECT MEMO
MHz 3 STEREO MONITOR ST.
TUNED
kHz DOWN MIX
DSP
R
SW
S
RS
4 Use the MULTI CONTROL keys to select the appropriate front
speakers setting.
1 FRNT NML (normal): Average size front speakers are
connected to the receiver.
2 FRNT LRG (large):
Large front speakers are connected to the receiver.
• For “FRNT LRG” selection, no sound will be heard from SUBW even
when it is set to ON. However, if you select CINEMA EQ. when
subwoofer is selected, you will be able to hear sound from the
subwoofer.
When in STEREO mode, the sound goes directly to front speaker.
If you selected “LRG” as the center speaker setting,
1 SURR LRG (large):
Large surround speakers are connected to the receiver.
2 SURR NML (normal): Average size surround speakers are
connected to the receiver.
3 SURR OFF:
Surround speaker setting mode to the
receiver is OFF.
If you have selected other than “LRG” as the center speaker
setting,
1 SURR ON:
Surround speaker setting mode to the receiver
is ON.
2 SURR OFF: Surround speaker setting mode to the receiver
is OFF.
9 Press the SET UP key again to accept the setting.
• The receiver enters the speaker volume level adjustment mode.
• In steps 3 and 4, indications appear only for the selected channels
of the speakers that require adjusting.
3 Adjust the speaker volume.
From your usual listening position, adjust the volume levels. The volume
levels from each speaker should be the same.
1 Use the MULTI CONTROL keys to adjust the volume of the test
tone output from the speaker channel to be adjusted.
The channel indication blinks while the test tone is being output.
SP
A B TI.VOL
CLIP
MUTE
RDS EON
PTY
TP
TA
NEWS
L
C
R
S
RS
LFE
LS
19
FM AUTO SOUND DIGITAL
AUTO
AM PRO LOGIC S.DIRECT MEMO
MHz 3 STEREO MONITOR ST.
TUNED
kHz DOWN MIX
DSP
The test tone is heard from the speakers in the following
sequence for 2 seconds each:
= L = C = R = SR = SL = SW
• If you change the volume level settings for the speakers while listening
to music, the settings referred to on this page are also changed.
•
• If the speaker setting selects are changed, the speaker level settings
are reset.
2 Press the SET UP key.
• The test tone is turned off. The receiver enters the mode for inputting
the distance to the speakers.
5 Press the SET UP key to accept the setting.
• The center speaker setting indication (CNTR) appears.
_4942/10-19/EN
19
If you selected “LRG” as the front speakers setting,
1 CNTR LRG (large):
A large center speaker is connected to
the receiver.
2 CNTR NML (normal): An average size center speaker is connected to the receiver.
3 CNTR OFF:
Center speaker setting mode to the
receiver is OFF.
Continued to next page
3/16/01, 3:05 PM
Preparations
Speaker settings
Preparing for surround sound
20
4 Input the distance to the speakers.
Normal playback
Preparing for playback
1 Measure the distance from the listening position to each of the
speakers.
Jot down the distance to each of the speakers.
Distance to front speakers:
____ feet____ meters
Distance to center speaker:
____ feet____ meters
Distance to surround speakers:
____ feet____ meters
Some preparatory steps are needed before starting playback.
ON/STANDBY
INPUT MODE
AUTO/CINEMA EQ.
2 Use the MULTI CONTROL keys to select the distance to the
front speakers.
The speaker indicator to be adjusted blinks.
SP
A B TI.VOL
CLIP
MUTE
RDS EON
PTY
TP
TA
NEWS
L
C
LFE
LS
FM AUTO SOUND DIGITAL
AUTO
AM PRO LOGIC S.DIRECT MEMO
MHz 3 STEREO MONITOR ST.
TUNED
kHz DOWN MIX
DSP
R
SW
S
RS
Indication in feet
Indication in meters
• The allowable setting range is 1 to 30 feet (0.3 to 9.0 m), adjustable
in 1 foot (0.3 m) increments.
3 Press the SET UP key to accept the settings.
4 Repeat steps 2 and 3 to input the distance for each of the
speakers.
KRF-V6050D/
V5050D/
V5550D
POWER
INPUT SELECTOR
SPEAKERS A/B
(SPEAKER/MUTE)
Selecting the input mode
If you have selected a component connected to the CD/DVD, DVD/6ch,
DVD (VR-505/KRF-V5550D only) or VIDEO2/MONITOR jacks, make
sure that the input mode setting is correct for the type of audio signal to
be used.
9
Selecting MD/TAPE
5 Setup is complete when the input indication reappears.
Operations
SP
A B TI.VOL
CLIP
MUTE
RDS EON PTY
TP
TA
NEWS
L
C
LFE
LS
R
Select the source name corresponding to the component connected to
the MD/TAPE jacks. The initial factory setting is “TAPE”. To change the
source to “MD,” follow the steps below:
SW
S
RS
1 Use the INPUT SELECTOR knob to select “TAPE”.
Display when all speakers have been selected.
2 Hold down the AUTO/CINEMA EQ. key for more than 2 seconds.
• The speakers you have selected should appear on the display.
Confirm that all the speakers have been correctly selected.
• The source indication changes to “MD”.
• To return to the original indication, repeat procedure 2.
Selecting the speaker system (VR-506/KRF-V6050D only)
Input level adjustment (analog sources only)
If the input level of an analog source signal is too high, adjust the input
level. The CLIP indicator will blink to indicate the source signal.
CLIP
RDS
TP
1 Use the INPUT SELECTOR knob to select the source which
input level you want to adjust.
• You can store a separate input level for each input source. If the
MONITOR function is ON, you can store an input level for when
MONITOR is on independently of the input levels for the input
sources.
2 Press the SOUND key repeatedly until the “INPUT” indication
appears.
3 Use the MULTI CONTROL keys to adjust the input level.
SP
A B TI.VOL
CLIP
MUTE
RDS EON PTY
TP
TA
NEWS
L
C
LFE
LS
FM AUTO SOUND DIGITAL
AUTO
AM PRO LOGIC S.DIRECT MEMO
STEREO MONITOR ST.
MHz 3 STEREO
TUNED
kHz DOWN MIX
DSP
R
SW
S
RS
The indicator for the speakers
you want to use should be lit.
SP
A B TI.VOL
CLIP
MUTE
RDS EON PTY
TP
TA
NEWS
L
C
LFE
LS
R
SW
S
RS
VR-506/KRF-V6050D
The speaker indicator lights.
SP
A B TI.VOL
CLIP
MUTE
RDS EON
PTY
TP
TA
NEWS
L
C
LFE
LS
R
SW
S
RS
VR-505/517/KRF-V5050D/
V5550D
• Selecting “6ch INPT” by pressing the INPUT MODE key, whereby “DVD/
6ch” is the input source will cause SPEAKER A to be selected automatically.
On the VR-505/517/KRF-V5050D/V5550D, press the SPEAKER key to
switch the speakers on and off.
• The adjustment mode is displayed for approximately eight seconds.
• The input level may be adjusted to any one of three settings: 0dB,
-3dB, and -6dB. (The initial setting is 0dB.)
4 Press the SOUND key again to return to the input indication.
_4942/20-22/EN
Press the SPEAKERS A or B key to select the speaker system to
be used.
A ON
: Sound from the speakers connected to the SPEAKERS A
terminals on the rear panel.
B ON
: Sound from the speakers connected to the SPEAKERS B
terminals on the rear panel.
A+B ON : Sound from both the speakers connected to the
SPEAKERS A and B terminals on the rear panel.
A+B OFF : No sound from the speakers. Use this setting when listening
with headphones for stereo sound in all playback modes.
20
Turning on the receiver
1 Turn on the power to the related components.
2 Turn on the power to this receiver by pressing POWER (and ON/
STANDBY) key(s).
3/16/01, 3:07 PM
Normal playback
Listening to a source component
VOLUME CONTROL
INPUT SELECTOR
2 Start playback from the selected source.
3 Use the VOLUME CONTROL knob (VOLUME keys) to adjust
21
the volume.
Selecting VIDEO 2/MONITOR
Depending on the component connected to the VIDEO 2/MONITOR
jacks, select either the “VIDEO 2” setting or the “MONITOR” setting, as
9
appropriate.
Adjusting the sound
MULTI CONTROL
SOURCE DIRECT
SOUND
INPUT
SELECTOR
VOLUME
RC-R0615/R0617
RC-R0511
SPEAKERS A/B
PHONES (SPEAKER/MUTE)
VOLUME CONTROL
1 Use the INPUT SELECTOR knob to select the source you
want to listen to.
VR-506/KRF-V6050D
1
2
3
4
5
6
7
8
6
7
“PHONO”
“TUNER”
“CD/DVD”
“TAPE” or “MD”
“VIDEO1”
if VIDEO2/MONITOR is VIDEO2
“VIDEO2”
“DVD/6ch”
“AV AUX”
else if VIDEO2/MONITOR is MONITOR
“DVD/6ch”
“AV AUX”
KRF-V5050D
1
2
3
4
5
“PHONO”
“TUNER”
“CD/DVD”
“TAPE” or “MD”
“VIDEO1”
if VIDEO2/MONITOR is VIDEO2
6 “VIDEO2”
7 “DVD/6ch”
else if VIDEO2/MONITOR is MONITOR
6 “DVD/6ch”
VR-505
1
2
3
4
5
“AUX”
“TUNER”
“CD/DVD”
“TAPE” or “MD”
“VIDEO1”
if VIDEO2/MONITOR is VIDEO2
6 “VIDEO2”
7 “DVD”
else if VIDEO2/MONITOR is MONITOR
6 “DVD”
VR-517/KRF-V5550D
1
2
3
4
5
6
7
8
6
7
“AUX”
“TUNER”
“CD/DVD”
“TAPE” or “MD”
“VIDEO1”
if VIDEO2/MONITOR is VIDEO2
“VIDEO2”
“DVD/6ch”
“AV AUX” (VR-517 only)
else if VIDEO2/MONITOR is MONITOR
“DVD/6ch”
“AV AUX” (VR-517 only)
_4942/20-22/EN
21
Operations
The input sources change as shown below:
Selecting a source using the INPUT SELECTOR knob.
SOUND
MULTI
CONTROL
BASS BOOST/
B. BOOST
VOLUME
MUTE
RC-R0511
RC-R0615/R0617
Adjusting the tone
You can adjust the sound quality when the receiver is in the PCM stereo
and analog stereo mode.
1 Press the SOUND key to select the tone mode to be adjusted.
BASS: Select this to adjust the low frequency range.
(Press the SOUND key once.)
TREB: Select this to adjust the high frequency range.
(Press the SOUND key twice.)
SP
A B TI.VOL
CLIP
MUTE
RDS EON
PTY
TP
TA
NEWS
L
C
LFE
LS
R
SW
S
RS
FM AUTO SOUND DIGITAL
AUTO
AM PRO LOGIC S.DIRECT MEMO
MHz 3 STEREO MONITOR ST.
TUNED
DSP
kHz DOWN MIX
2 Use the MULTI CONTROL keys to adjust the sound quality.
• The bass and treble levels are adjustable from -10dB to +10dB in 2
step increments.
• The adjustment item is displayed for approximately 8 seconds.
Once-touch low frequency emphasis (bass boost)
(remote control only)
You can adjust the sound quality when the receiver is in the PCM stereo
and analog stereo modes.
Press the B. BOOST (BASS BOOST) key.
• Press the key once to select the maximum (+10dB) low frequency
emphasis setting.
• This key does not function when the receiver is in the sound quality or
ambience effects adjustment mode.
Switching back to the previous setting
Press the B. BOOST (BASS BOOST) key again.
3/16/01, 3:07 PM
Normal playback
22
Recording
Recording audio (analog sources)
Muting the sound
MONITOR
The MUTE key lets you mute the sound of the speakers.
Press the MUTE key.
SP
A B TI.VOL
MUTE
CLIP
RDS EON
PTY
TP
TA
NEWS
L
C
LFE
LS
R
SW
S
RS
Blinks
To cancel
INPUT SELECTOR
Press the MUTE key again so that the “MUTE” indicator goes off.
• MUTE ON can also be deactivated by turning the volume control
knob.
SOURCE DIRECT playback (for analog input sources only)
Use this function to pass the source material direct to the amplifier,
bypassing any audio processing.
Press the SOURCE DIRECT key.
Recording a music source
When recording a music source, switch the VIDEO2/MONITOR
setting to “MONITOR”.
9
1 Use the INPUT SELECTOR knob to select the source (other than
“TAPE”) you want to record.
2 Set the cassette deck or MD recorder to record.
3 Start playback, then start recording.
FM AUTO SOUND DIGITAL
AUTO
AM PRO LOGIC S.DIRECT MEMO
MHz 3 STEREO MONITOR ST.
TUNED
kHz DOWN MIX
DSP
Recording tapes or MD (with MONITOR function)
Operations
• When you press the LISTEN MODE, SOUND, or SET UP keys, or
switch to another input source, SOURCE DIRECT playback will be
canceled.
• If CINEMA EQ. is switched ON, SOURCE DIRECT key will not be
effective.
To cancel
When recording a music source, switch the VIDEO2/MONITOR
setting to “MONITOR”.
9
MONITOR = MD/TAPE recording
1 Press the MONITOR key.
Press the SOURCE DIRECT key again.
• If SOURCE DIRECT playback was activated while in surround mode,
canceling SOURCE DIRECT playback will reactivate the previous
surround mode.
Listening with headphones
1 (VR-506/KRF-V6050D)
Press the SPEAKERS A or B key so that the speaker indicator
goes off.
(VR-505/517/V5050D/V5550D)
Press the SPEAKER key so that the speaker indicator goes off.
Make sure the SPEAKERS
indicators are turned off.
SP
A B TI.VOL
CLIP
MUTE
RDS EON
PTY
TP
TA
NEWS
L
C
Make sure the SP indicators
are turned off.
SP
A B TI.VOL
CLIP
MUTE
RDS EON PTY
TP
TA
NEWS
R
LFE
LS
S
RS
VR-506/KRF-V6050D
L
C
R
S
RS
LFE
LS
VR-505/517/KRF-V5050D/
V5550D
• If you turn off all of the speakers when in surround mode, the
surround mode will be canceled as well, resulting in stereo playback.
2 Connect headphones to the PHONES jack.
PHONES
2 Use the INPUT SELECTOR knob to select a source other than
“MD/TAPE”.
3 Start playback on the cassette deck connected to the MONITOR
jacks and start recording on the cassette deck or MD recorder
connected to the MD/TAPE jacks.
MD/TAPE = MONITOR recording
1 Use the INPUT SELECTOR knob to select “MD/TAPE.”
2 Start playback on the cassette deck connected to the MD/TAPE
jacks and start recording on the cassette deck or MD recorder
connected to the VIDEO2/MONITOR jacks.
• To copy tapes using a double cassette deck, refer to the instruction
manual of the double cassette deck.
MONITOR function (analog sources only)
You can connect a cassette deck or graphic equalizer to the VIDEO2/
MONITOR jacks of the receiver. If a graphic equalizer is connected, the
MONITOR key should be left in the on position. Alternately, if a cassette
deck equipped with a 3-head system is connected to the VIDEO2/
MONITOR jacks, you will be able to monitor the just-recorded signal
while making recordings on the cassette deck. By switching the MONITOR key on and off, you can compare the sound of the source signal
and the just-recorded signal. For more information, refer to the instruction manual of the connected component.
3 Use the VOLUME CONTROL knob (VOLUME keys) to adjust the
volume.
_4942/20-22/EN
22
FM AUTO SOUND DIGITAL
AUTO
AM PRO LOGIC S.DIRECT MEMO
MHz 3 STEREO MONITOR ST.
TUNED
kHz DOWN MIX
DSP
3/16/01, 3:07 PM
Recording
Listening to radio broadcasts
The receiver can store up to 40 stations in the memory and recall them by
one-touch operation.
Recording video
1 Use the INPUT SELECTOR to select the video source (other than
“VIDEO1”) you want to record.
23
Tuning radio stations
2 Set the video deck connected to VIDEO 1 to record.
• Select the REC MODE to record a digital input source.
MULTI CONTROL
3 Start playback, then start recording.
• Recording may not be normal for some video software. This is due to
the copy guard condition.
·
INPUT SELECTOR
Recording audio (digital sources)
Switch on the REC mode to record a digital input source.
Usually use the A-REC (Auto-Record) mode to record audio input
sources. When the digital mode changes during recording in the A- REC
mode, the audio input source may be interrupted momentarily.
BAND AUTO/CINEMA EQ.
Recording music in A-REC or M-REC mode
MULTI
CONTROL
DIMMER
BAND
AUTO
RC-R0511
INPUT SELECTOR
1 Use the INPUT SELECTOR to select the source (CD, DVD or
VIDEO2) you want to record.
2 Set the cassette deck or MD recorder to record.
3 Press and hold the DIMMER key for more than 2 seconds to
select the A-REC or M-REC mode.
• The mode changes every 2 seconds as shown below.
1 Rec mode off :
2 A-REC :
3 M-REC :
The digital input record mode is
switched off.
The digital input signals (DTS,
Dolby Digital, or PCM) are identified automatically and converted
into stereo signals that are ready
for recording.
The input signal type at the moment this mode is selected is held
throughout this mode.
For A-REC mode:
FM AUTO SOUND DIGITAL
AUTO
AM PRO LOGIC S.DIRECT MEMO
MHz 3 STEREO MONITOR ST.
TUNED
kHz DOWN MIX
DSP
FM AUTO SOUND DIGITAL
AUTO
AM PRO LOGIC S.DIRECT MEMO
MHz 3 STEREO MONITOR ST.
TUNED
kHz DOWN MIX
DSP
RC-R0615/R0617
1 Use the INPUT SELECTOR knob (TUNER key) to select the
tuner.
2 Use the BAND key to select the desired broadcast band.
Each press switches the band
as follows:
1 FM
2 AM
FM AUTO SOUND DIGITAL
AUTO
AM PRO LOGIC S.DIRECT MEMO
MHz 3 STEREO MONITOR ST.
TUNED
kHz DOWN MIX
DSP
3 Use the AUTO/CINEMA EQ. key to select the desired
tuning method.
Each press switches the tuning method as follows:
1 AUTO lit (auto tuning)
2 AUTO not lit (manual tuning)
• Normally, set to “AUTO” (auto tuning). If the radio waves are weak
and there is a lot of interference, switch to manual tuning. (With
manual tuning, stereo broadcasts will be received in monaural.)
4 Use the MULTI CONTROL keys to select the station.
Frequency
display
4 Start playback, then start recording.
“TUNED” is displayed when a
station is received.
Auto tuning
:
Manual tuning :
The next station is tuned automatically.
Turn the knob (press the key) to select the
desired station.
• If the audio reproduction stops in the middle due to change in the
input signals, etc., press the DIMMER key.
23
“ST.” lights when a broadcast
is being received in stereo.
FM AUTO SOUND DIGITAL
AUTO
AM PRO LOGIC S.DIRECT MEMO
MHz 3 STEREO MONITOR ST.
TUNED
DSP
kHz DOWN MIX
FM AUTO SOUND DIGITAL
AUTO
AM PRO LOGIC S.DIRECT MEMO
MHz 3 STEREO MONITOR ST.
TUNED
kHz DOWN MIX
DSP
FM AUTO SOUND DIGITAL
AUTO
AM PRO LOGIC S.DIRECT MEMO
MHz 3 STEREO MONITOR ST.
TUNED
kHz DOWN MIX
DSP
“AUTO” indicator lights up
in the display.
FM AUTO SOUND DIGITAL
AUTO
AM PRO LOGIC S.DIRECT MEMO
MHz 3 STEREO MONITOR ST.
TUNED
kHz DOWN MIX
DSP
For M-REC mode:
_4942/23-25/EN
“AM” or “FM” indicator
appears in the display
3/16/01, 3:08 PM
Operations
TUNER
Listening to radio broadcasts
24
Presetting radio stations manually
Receiving preset stations in order (P.CALL)
MULTI CONTROL
MEMORY
P.CALL
4/¢
TUNER
1 Tune to the station you want to store.
RC-R0511
2 Press the MEMORY key while receiving the station.
Blinks for 5 seconds
SP
A B TI.VOL
CLIP
MUTE
RDS EON PTY
TP
TA
NEWS
L
C
LFE
LS
Lights for 5 seconds
FM AUTO SOUND DIGITAL
AUTO
AM PRO LOGIC S.DIRECT MEMO
MHz 3 STEREO MONITOR ST.
TUNED
kHz DOWN MIX
DSP
R
SW
S
RS
Proceed to step 3 within 5 seconds.
(If more than 5 seconds elapse, press the MEMORY key again).
RC-R0615/R0617
1 Press TUNER key to select the tuner as the source.
2 Use the P.CALL 4/ ¢ key to select the desired station.
• Each time you press the key, another preset station is received in
order.
Pressing the P.CALL ¢ does the following:
3 Use the MULTI CONTROL
=01=02=03= ... = ... 38=39=40
keys to select one of the station
presets (1 – 40).
Operations
Pressing the P.CALL 4 does the following:
4 Press the MEMORY key again to confirm the setting.
• Repeat steps 1, 2, 3, and 4 to store as many stations as necessary.
• If you store a station at a previously used preset, the old station will
be replaced by the new one.
01+02+03+ ... + ... 38+39+40+
Holding down the ¢ or 4 key, lets you skip through the
presets, receiving each preset station at 0.5 second intervals.
Receiving preset stations
Numeric keys
TUNER
RC-R0511
RC-R0615/R0617
1 Press TUNER to select tuner as the source.
2 Enter the number of the preset station you want to receive
(up to “40”).
Press the numeric keys in the following order:
For "15", press .......... 0,5
For "20", press .......... 0,0,)
• If you make a mistake entering a two digit number, press the +10 key
repeatedly to return to the original display and start again.
SP
A B TI.VOL
CLIP
MUTE
RDS EON PTY
TP
TA
NEWS
_4942/23-25/EN
L
C
LFE
LS
FM AUTO SOUND DIGITAL
AUTO
AM PRO LOGIC S.DIRECT
MHz 3 STEREO MONITOR ST.
TUNED
DSP
kHz DOWN MIX
R
SW
S
RS
24
3/16/01, 3:09 PM
Ambience effects
This receiver is equipped with listening modes that allow
you to enjoy an enhanced sonic ambience with a variety of
video sources.
In order to obtain the optimum effect from the surround
modes, make sure to input the proper speaker settings
beforehand.
(
Dolby Digital
The Dolby Digital surround format lets you enjoy up to 5.1 channels of
digital surround sound from Dolby Digital program sources (such as
25
). Compared with previous
Laserdisc or DVD software marked
Dolby surround, Dolby Digital provides even better sound quality,
greater spatial accuracy, and improved dynamic range.
Note
Although a full set of speakers (front left, right, and center, surround left
and right, and a subwoofer) is required for true 5.1 channel Dolby Digital
surround sound, this receiver lets you enjoy Dolby Digital (and Dolby
Surround) program sources, even if you connect only the front speakers.
Surround modes
DTS
The DTS multi-channel audio format is available on CD, LD and DVD
software. DTS is a strictly digital format and can not be decoded inside
most CD, LD or DVD players. For this reason, if you attempt to listen to
DTS encoded software through the analog output of your new CD, LD
or DVD player, you will experience digital noise in most cases. This noise
can be quite loud if the analog output is connected directly to a high
power amplification system. Proper measures for playing the digital
output as described below should be taken to avoid this situation. To
enjoy DTS Digital Surround playback, an external 5.1 channel DTS
Digital Surround decoder system or an amplifier with a built-in DTS
Digital Surround decoder must be connected to the digital output (S/P
DIF, AES/EBU or TosLink) of a CD, LD or DVD player.
All models are incorporated with the DTS decoder.
Center speaker
Subwoofer (SW)*
Front speakers (L, R)
Center speaker
Subwoofer (SW)*
Front speakers (L, R)
* LFE = Low Frequency Effects. This channel delivers separate nondirectional bass signals to the subwoofer for more dynamic deep bass
sound effects.
Although only Dolby Digital soundtracks incorporate a separate low
frequency channel, connecting a subwoofer will also improve deep bass
performance in the other surround modes.
The indication “LFE” appears in the display when a signal is being input
for this channel.
Surround speakers (L, R)
* Optional in this mode.
* LFE = Low Frequency Effects. This channel delivers separate
non-directional bass signals to the subwoofer for more dynamic
deep bass sound effects.
DTS has a .1 or LFE channel.
The indication “LFE” appears in the display when a signal is
being input for this channel.
Manufactured under license from Digital Theater
Systems, Inc. US Pal. No. 5,451,942 and other
worldwide patents issues and pending.
“DTS” and “DTS Digital Surround” are trademarks
of Digital Theater Systems, Inc.
© 1996 Digital Theater Systems, Inc. All rights
reserved.
Dolby Pro Logic
Dolby Pro Logic is a specially encoded 2 channel surround format
designed to provide theater-like surround sound from Dolby Surround
encoded sources (such as video and Laserdisc software marked
). This receiver is equipped with a Dolby Pro Logic
surround decoder to let you enjoy the wide variety of currently available
Dolby Surround home video software. Surround signal is monaural.
Center speaker
Subwoofer (SW)
Front speakers (L, R)
Surround speakers (L, R)
Manufactured under license from Dolby Laboratories. Dolby, Pro Logic
and the double-D symbol are trademarks of Dolby Laboratories.
Confidential Unpublished Works. ©1992-1997 Dolby Laboratories. All
rights reserved.
_4942/23-25/EN
25
3/16/01, 3:09 PM
Operations
Surround speakers (L, R)
Ambience effects
26
Dolby 3 Stereo
Dolby 3 Stereo is available for systems that do not have surround
speakers. When in the Dolby 3 Stereo mode, the surround information
is redirected to the front left and right speakers. This mode is designed
for use with Dolby Surround program sources, but can also improve
sound field unity for programs that are not Dolby Surround encoded.
Dialog positioning and sound image definition, however, may not be as
accurate when used with programs that are not Dolby Surround
encoded.
Center speaker
Subwoofer (SW)
Front speakers (L, R)
DVD 6-channel mode
(except VR-505/KRF-V5550D)
Using a DVD player or the like equipped with six (5.1) output channels
and the receiver, you can enjoy multi-channel encoded DVD source
material in all its splendor. Since the source signals are digital and each
channel is input independently, the resulting sound quality, sense of
spaciousness, and dynamic range are superb.
Center speaker
Subwoofer (SW)*
Front speakers (L, R)
Surround speakers (L, R)
DSP mode
The DSP mode lets you add the atmosphere of a live concert or hall to
almost any type of program source. These modes are particularly effective
when used with stereo program sources, like CD, television, and FM radio.
You might enjoy trying the ARENA, JAZZ CLUB, THEATER, STADIUM or
DISCO mode the next time you watch a concert or sporting event!
*LFE = Low Frequency Effects. This channel delivers separate nondirectional bass singnals to the subwoofer for more dynamic deep
bass sound effects.
Operations
Center speaker
Subwoofer (SW)
Front speakers (L, R)
Surround speakers (L, R)
What's DSP?
DSP stands for Digital Signal Processor.
The way a sound is heard in an actual environment depends on a variety
of different factors. One of the most important is reverberation (the act
of decaying elements of sound echoing in various places).
The DSP modes produce the feeling of presence by using the DSP to
create reverberation, without spoiling the sound quality of the original
signal.
_4942/26-31/EN
26
3/16/01, 3:09 PM
Surround play
When the DTS signal is input:
(The DTS indicator lights up.)
The DTS compatible models can reproduce a CD, DVD, or LD carrying
the DTS mark.
DOLBY DIGITAL can be used when playing DVD or LD software bearing
mark and DOLBY DIGITAL format digital broadcasts (etc.).
the
DOLBY PRO LOGIC and DOLBY 3 STEREO can be used when playing
mark.
video, DVD, or LD software bearing the
INPUT MODE INPUT SELECTOR
LISTEN MODE
When the analog signal or the digital signal (except for
DOLBY DIGITAL or DTS signal) is input:
1 PRO LOGIC: PRO LOGIC surround (The PRO LOGIC
indicator lights up.)
2 3 STEREO: 3-STEREO surround (The 3 STEREO indica
tor lights up.)
3 ARENA: DSP surround.
4 JAZZ CLUB: DSP surround.
5 THEATER: DSP surround.
6 STADIUM: DSP surround.
7 DISCO: DSP surround.
8 STEREO: Normal stereo playback. Sound is produced
from the two front channels only.
• If a Dolby Digital signal having more channels than the maximum
number of playback channels available using the receiver’s current
settings is input, the DOWNMIX indicator on the front panel lights up
and downmixing is performed to match the number of available
channels.
LSTN M.
LISTEN MODE
RC-R0615/R0617
Preparations
• Turn ON related components.
• Complete “Preparing for surround sound” (speaker settings). (
• Use the INPUT SELECTOR to select the component you wish to play
back with surround sound.
• Use the INPUT MODE key to select the input mode (analog or digital)
for the source you wish to play back.
9
• Noise will be produced when a DTS source is played by selecting the
analog input.
Notes
• Depending on the type of the signal or speaker setting, some listening
modes cannot be selected.
• When playback is started, the sound may be cut or interrupted before
the input source is confirmed as Dolby Digital.
• To enjoy Dolby Digital surround (as well as all the other listening
modes) from a single component, be sure to use a Dolby Digital
compatible source component. Connect the Dolby Digital compatible
source component's Dolby Digital format digital audio signal to one of
the DIGITAL INPUT jacks on the back of the receiver. Connect the
normal audio signal correctly to the respective component's AUDIO
jacks.
0!@#
1 Start playing the video software.
2 Press the LISTEN MODE (LSTN
M.) key to select the
listening mode.
The listening mode settings are stored separately for each input. If the
input mode is set to digital auto (“AUTO SOUND” lights), the receiver
selects the optimal listening mode automatically based on the type of
input signal and the speaker settings.
Each press of the LISTEN MODE (LSTN M.) key switches the
setting as listed below.
The listening mode settings are different depending on the type
of input signal.
When the DOLBY DIGITAL signal is input:
(The DOLBY DIGITAL, PROLOGIC, or 3 STEREO indicator lights up.)
1 DOLBY DIGITAL: DOLBY DIGITAL surround
2 PRO LOGIC: PRO LOGIC surround (The PRO LOGIC
indicator lights up.)
3 3 STEREO: 3-STEREO surround
4 STEREO: Normal stereo playback
When you select DOLBY DIGITAL
SP
A B TI.VOL
CLIP
MUTE
RDS EON PTY
TP
TA
NEWS
_4942/26-31/EN
L
C
R
S
SR
AUTO
FM AUTO SOUND DIGITAL
AM PRO LOGIC S.DIRECT MEMO
MHz 3 STEREO MONITOR ST.
TUNED
kHz DOWN MIX
DSP
LFE
SL
27
3/16/01, 3:10 PM
Operations
3 Adjust the volume.
INPUT
SELECTOR
RC-R0511
27
1 DTS: DTS surround
2 STEREO: Normal stereo playback
Ambience effects
DVD 6-channel playback
28
Convenient functions
(VR-506/517/KRF-V6050D/V5050D)
Using a DVD player or the like equipped with six (5.1) output channels and
the receiver, you can enjoy surround sound playback.
When you try to play a disc other than Dolby Digital such as DTS CD, no
sound is produced or, noise may be heard. To avoid this situation, make
sure that you connect the component to the receiver’s DVD/6ch. INPUT
jacks through a surround processor which can decode the surround
signal you wont to listen to.
Connecting a DVD player which can decode the surround signal itself is
also acceptable.
MULTI CONTROL
DIMMER
INPUT MODE INPUT SELECTOR
SOUND
SOUND
MULTI
CONTROL
RC-R0511
RC-R0615/R0617
Operations
DVD
Adjusting the sound
You can make further adjustments to the sound while listening to playback
in the surround mode.
RC-R0511
RC-R0615/R0617
1 Press the SOUND key until the desired item appears in the
display.
Preparations
• Connect your DVD player to the DVD/6ch jacks of the receiver.
• Turn on all other components that will be used.
• Complete “Preparing for surround sound”.
(
1 Select “DVD/6ch” as the input source.
• If speaker system B is on when “DVD/6ch” is selected as the input
source, it switches off and speaker system A turns on automatically.
2 Select "6ch INPT" by pressing the INPUT MODE key.
Each time you press the button, the menu changes as follows:
Note that some items are not displayed in certain modes.
1
2
3
4
5
6
7
8
BASS (low frequency range sound quality adjustment)
TREB (high frequency range sound quality adjustment)
C (center speaker level adjustment)
SR (right surround speaker level adjustment)
SL (left surround speaker level adjustment)
SW (subwoofer level adjustment)
INPUT (input level adjustment)
NIGHT (midnight mode on/off)
¡
¡
)
2 Use the MULTI CONTROL keys to adjust the setting as desired.
3 Start playback of the DVD software.
• The adjustment item is displayed for approximately 8 seconds.
4 Adjust the volume.
• It is not possible to adjust the volume level or sound quality (SET UP,
SOUND) of the channels separately when the receiver is in the DVD/
6ch mode. Adjust the volume with the controls of the DVD player.
For the powered subwoofer, you can adjust the volume of the
subwoofer using the subwoofer’s own volume control.
_4942/26-31/EN
28
3/16/01, 3:10 PM
Ambience effects
Midnight mode (Dolby Digital mode only)
29
When watching movies at night you might not be able to raise the volume
as loud as normal. Midnight mode compresses the dynamic range of
previously specified parts of the Dolby Digital sound track (like scenes with
sudden increases in volume) to minimize the difference in volume between
the specified and non-specified parts. This makes it easy to hear all of the
sound track, even when listening at low volumes.
1 Press the SOUND key repeatedly until “NIGHT” appears on the
display.
• This can be selected only if CD/DVD, DVD (VR-505/KRF-V5550D
only) or VIDEO2 is selected as the source and the listen mode is set
to “DOLBY DIGITAL.”
2 Use the MULTI CONTROL keys to select the ON or OFF setting.
SP
A B TI.VOL
CLIP
MUTE
RDS EON PTY
TP
TA
NEWS
L
C
R
S
SR
FM AUTO SOUND DIGITAL
AUTO
AM PRO LOGIC S.DIRECT MEMO
MHz 3 STEREO MONITOR ST.
TUNED
kHz DOWN MIX
DSP
LFE
SL
• The adjustment item is displayed for approximately 8 seconds.
• Some Dolby Digital software may not be compatible with the Midnight mode.
Display dimmer adjustment
Operations
The dimmer function lets you select the brightness of the receiver's
display. You might find this useful if you darken your room to watch movies
or listen to music.
Each time you press the DIMMER key, the display brightness
changes among the three available settings. Select the brightness level you find most pleasing.
SP
A B TI.VOL
CLIP
MUTE
RDS EON PTY
TP
TA
NEWS
LFE
SP
A B TI.VOL
CLIP
MUTE
RDS EON PTY
TP
TA
NEWS
LFE
SP
A B TI.VOL
CLIP
MUTE
RDS EON PTY
TP
TA
NEWS
LFE
L
C
FM AUTO SOUND DIGITAL
AUTO
AM PRO LOGIC S.DIRECT MEMO
MHz 3 STEREO MONITOR ST.
TUNED
kHz DOWN MIX
DSP
R
SW
S
L
C
AUTO
FM AUTO SOUND DIGITAL
AM PRO LOGIC S.DIRECT MEMO
MHz 3 STEREO MONITOR ST.
TUNED
kHz DOWN MIX
DSP
R
SW
S
L
C
FM AUTO SOUND DIGITAL
AUTO
AM PRO LOGIC S.DIRECT MEMO
MHz 3 STEREO MONITOR ST.
TUNED
kHz DOWN MIX
DSP
R
SW
S
96kHz LPCM playback
The receiver is compatible with the 96kHz LPCM playback. To play a
96kHz DVD, set the listen mode to “STEREO”.
• When “96kHz” appears in the display, press the LISTEN MODE key
(the listen mode changes to the STEREO mode).
_4942/26-31/EN
29
3/16/01, 3:10 PM
Basic remote control operations for other components
(For VR-506/517/KRF-V6050D/V5550D)
30
The remote control supplied with this receiver (for VR-506/517/
KRF-V6050D/V5550D only) is also capable of controlling components from a variety of manufacturers once you register the
appropriate setup codes into the remote control unit.
Low battery warning
Replace all four batteries with new ones when you notice a shortening
of the distance from which the remote control will operate. The remote
control is designed to retain setup codes in memory while you change
batteries.
4 Repeat steps 2 to 3 to register additional components
until all components have been registered.
Note
Although each setup code is designed to work with a number of different
models, certain codes may not work with some models. (Also, certain
codes may only operate some of the functions available on a given
model.)
Operating other components
Registering setup codes for other components
This operation lets you operate the registered components.
KENWOOD audio components with system control turn on and off
automatically with the receiver via the system control connections.
POWER
Source
POWER
keys
Numeric keys
POWER
Source
POWER
keys
RECEIVER
RC-R0615/R0617
RC-R0615/R0617
1 Find the setup code of the component to be registered.
• Refer to the setup code lists to find the setup code for the component
to be registered.
⁄
Example: To register a DVD made by KENWOOD, you would enter
"805".
Input
Component
Maker
Code
Key
(DVD)
DVD player
KENWOOD
805, 808
DVD
1 Use the input selector keys to select the component you
desire.
• Pressing the input selector keys also changes the input selector on
the receiver.
• When you operate your registered TV, VCR, DVD player, Cable
tuner, or DSS receiver, go to step 2.
• When you operate the CD player, Cassette deck, MD player, or
Tuner with system control connection, go to step 3.
2 Press the source POWER key.
Remote Control
3 Press the operation keys you desire.
›
• To return to the receiver operation mode, press the RECEIVER key.
The remote control mode returns to the receiver operation mode
when you do not operate for more than 15 seconds.
2 Hold down the POWER key and press the numeric keys to
enter the setup code.
• Example: Press “805” to register a DVD player made by KENWOOD.
• If you push an invalid key, the remote will exit the setup mode.
3 Press the source POWER (TV, VCR, DVD, CABLE, DSS)key
for more than 2 seconds, and check to see that the
component you want to control turns on.
Note
Be sure to point the remote control at the remote sensor on the receiver
when you want to operate KENWOOD components connected by
system control cords. Otherwise, point the remote control at the component you want to operate.
If the component does not react, and there is more than one
setup code, enter another setup code and try again.
• 6, TUNING 1/¡, or MULTI CONTROL key(s) can also be used
instead of the POWER key.
• If the component is already on, pressing the source POWER keys will
turn it off.
_4942/26-31/EN
30
3/16/01, 3:10 PM
Basic remote control operations for other components
Setup code chart
VCR Setup codes
TV Setup codes
ZENITH
MAGNAVOX
SHARP
PANASONIC
SAMSUNG
JVC
HITACHI
PIONEER
PROSCAN
QUASAR
PHILIPS
SANYO
TOSHIBA
MITUBISHI
LOEWE
Setup codes
101
102
103, 104, 105,
106, 117
107, 108
109
110
111,112, 122
109
113
114, 115
116
117
118
109
119
120
121
123, 124
CABLE Setup codes
Maker
JERROLD
S.ATLANTA
ZENITH
PIONEER
TOCOM
G.I.
HAMLIN
OAK
MACOM
GEMINI
PHILIPS
PANASONIC
SAMSUNG
_4942/26-31/EN
Maker
SONY
GE/HITACHI
RCA/HITACHI
PANASONIC
MAGNAVOX
TOSHIBA
MITSUBISHI
SHARP
G.E
ZENITH
GOLD STAR
JVC
PHILIPS
HITACHI
SANYO
TOSHIBA
Setup codes
301, 302, 303,
304, 305, 306
307
308
309, 310
311, 312, 313
314
315, 316, 317,
318
319, 320
321
322
323
324, 325, 326,
327
313
328, 329
330
331
Maker
JVC
SONY
PIONEER
PANASONIC
KENWOOD
TOSHIBA
PHILIPS
Setup codes
801
802
803
804
805, 808
806
807
DSS Setup codes
Setup codes
201, 202
203
204, 205
206, 207
208
209
210, 211
212, 213, 214
215, 216, 217
218
219, 220
221, 222
223
31
Maker
RCA
G.I.
ECHOSTAR
TOSHIBA
PANASONIC
HUGHES
SONY
HITACHI
PRIMESTAR
Setup codes
901
902
903
904
905
906
907
908
909
Remote Control
Maker
SONY
GE/RCA
RCA
31
DVD Setup codes
3/16/01, 3:10 PM
Basic remote control operations for other components
DVD player operation keys (For VR-505/KRF-V5050D)
32
The remote control of this unit can control two groups of KENWOOD DVD players directly without using the
remote control supplied with the DVD player.
Group-1: DV-4900, DV-4070B, DV-2070, DV-203, DVF-9010, DVF-K7010, DVF-5010, DVF-R9030, DVFR7030, DVF-3530 and DV-402
Group-2: DV-4050, DV-303, DVF-R6030, DVF-K5020, DVF-5020, DVF-3020 and DVF-3030
Depending on your KENWOOD DVD model, you need to set up your receiver remote control as follows:
To set for Group-1 DVD players:
Press the numeric “1” key while pressing the “POWER” key (not the DVD Power key) on your remote
control.
To set for Group-2 DVD players:
Press the numeric “2” key while pressing the “POWER” key (not the DVD Power key) on your remote
control.
• If your DVD player is not listed in the list above, perform the set up for either Group-1 or Group-2.
When the set up is successful, then your DVD player falls into that particular group.
How to operate the DVD player with the remote control
1. Pressing the DVD Power key for more than 2 seconds turns the DVD player on or off.
2. To carry out the functions of the DVD player, first press the DVD Power key, then press each key
for each operation as explained in the DVD operation pages in the operating instructions. In this case,
the DVD operation mode is retained for 15 seconds after pressing any of those DVD operation
buttons.
(To turn the receiver operation mode within 15 seconds, press the RECEIVER key.)
DVD player operation keys
You can perform these basic operations using the keys described below when connected to KENWOOD DVD
player.
POWER
Numeric keys
(Select tracks)
1
2
3
4
5
6
DVD
DVD POWER
7
8
0
+10
MENU
SET UP
POWER
9
RECEIVER
OSD RETURN TITLE
SOUND LISTEN MODE
MENU (Menu)
OSD (OSD menu)
P.CALL
P.CALL
MULTI CONTROL
Remote Control
1 (Search)
¡ (Search)
TUNING
A/B+100
BASS BOOST DISC SKIP
PHONO/AUX
CD/DVD
ENTER
AUTO
TUNER
BAND
DVD
RECEIVER
(Receiver mode)
RETURN (Return)
TITLE (Title)
%(Cursor »)
fi(Cursor «)
#(Cursor \)
@(Cursor |)
ENTER (Enter)
6 (3 Play)
7 (Stop)
8 (Pause)
MD/TAPE
DVD
DISC SEL.
VIDEO1 VIDEO2 CINE.EQ
MUTE
VOLUME
RC-R0511
_4942/32-44/EN
32
3/16/01, 3:10 PM
Basic remote control operations for other components
CASSETTE deck, CD player & MD recorder operations
(For VR-505/KRF-V5050D)
33
You can perform these basic operations using the keys described below when connected to
KENWOOD cassette deck, MD recorder or CD player equipped with system control operations.
%
Cassette deck operation keys
CD player operation keys
POWER
POWER
1
2
3
4
5
6
7
8
0
+10
MENU
SET UP
DVD
Numeric keys
(Select tracks)
POWER
9
RECEIVER
TUNING
PHONO/AUX
BAND
AUTO
CD/DVD
TUNER
DVD
2 (Play)
6 (3 Play)
7 (Stop)
1 (Search)
¡ (Search)
DISC SKIP
MD/TAPE
5
6
7
8
9
0
+10
DVD
POWER
RECEIVER
OSD RETURN TITLE
SOUND LISTEN MODE
P.CALL
¢ (Skip up)
MULTI CONTROL
TUNING
A/B+100
BASS BOOST DISC SKIP
PHONO/AUX
CD/DVD
ENTER
AUTO
TUNER
BAND
DVD
6 (3 Play/Pause)
7 (Stop)
MD/TAPE
DVD
DISC SEL.
VIDEO1 VIDEO2 CINE.EQ
DVD
DISC SEL.
VIDEO1 VIDEO2 CINE.EQ
VOLUME
MUTE
VOLUME
MUTE
4
4 (Skip down)
ENTER
A/B+100
BASS BOOST DISC SKIP
3
P.CALL
P.CALL
MULTI CONTROL
1 (Rewind)
¡ (Fast forward)
2
MENU
SET UP
OSD RETURN TITLE
SOUND LISTEN MODE
P.CALL
1
RC-R0511
RC-R0511
MD recorder operation keys
POWER
2
3
4
5
6
7
8
0
+10
MENU
SET UP
9
RECEIVER
OSD RETURN TITLE
SOUND LISTEN MODE
P.CALL
P.CALL
4 (Skip down)
1 (Search)
¡ (Search)
+100 (Select track)
DVD
POWER
¢ (Skip up)
MULTI CONTROL
TUNING
A/B+100
BASS BOOST DISC SKIP
PHONO/AUX
Remote Control
Numeric keys
(Select tracks)
1
CD/DVD
ENTER
AUTO
TUNER
BAND
DVD
6 (3 Play)
7 (Stop)
MD/TAPE
DVD
DISC SEL.
VIDEO1 VIDEO2 CINE.EQ
MUTE
VOLUME
RC-R0511
Notes
1. Certain codes may only operate some of the function available on a given model.
2. The charts above show the typical functions available for each component. Some manufacturers use different key combinations to perform similar
functions. For that reason, we have programmed extra functions on some of the unused number keys to help you control your equipment.
_4942/32-44/EN
33
3/16/01, 3:11 PM
Basic remote control operations for other components
CASSETTE deck, CD player & MD recorder operations
34
(For VR-506/517/KRF-V6050D/V5550D)
You can perform these basic operations using the keys described below when connected to
KENWOOD cassette deck, MD recorder or CD player equipped with system control operations.
%
Cassette deck operation keys
POWER
POWER
1
2
3
4
5
6
7
8
9
0
+10
RETURN
LSTN M.
1
2
3
4
5
6
7
8
9
0
+10
RETURN
LSTN M.
TV
TV
VCR
VCR
MENU
SET UP
OSD
SOUND
DVD
CABLE
DSS
MENU
SET UP
OSD
SOUND
P.CALL
P.CALL
P.CALL
MULTI CONTROL
MULTI CONTROL
1 (Rewind)
¡ (Fast forward)
TUNING
B.BOOST
RECEIVER
TITLE
AUX
A/B+100
DISC SKIP
TV SEL.
CD/DVD
DVD
VIDEO1
MUTE
ENTER
VIDEO2
BAND
AUTO
DVD
INPUT SEL.
TUNER
DISC SEL.
CINE.EQ
VOLUME
RC-R0617
MD/TAPE
2 (Play)
6 (3 Play)
7 (Stop)
1 (Rewind)
¡ (Fast forward)
TUNING
B.BOOST
RECEIVER
TITLE
PHONO
CHANNEL
AV AUX
MUTE
34
ENTER
A/B+100
DISC SKIP
AUTO
TV SEL.
CD/DVD
INPUT SEL.
TUNER
DVD
VIDEO1
VIDEO2
3/16/01, 3:11 PM
BAND
DVD
DISC SEL.
CINE.EQ
VOLUME
RC-R0615
Remote Control
_4942/32-44/EN
DSS
POWER
POWER
P.CALL
DVD
CABLE
MD/TAPE
CHANNEL
AV AUX
2 (Play)
6 (3 Play)
7 (Stop)
Basic remote control operations for other components
CD player operation keys
35
POWER
POWER
Numeric keys
(Select tracks)
1
2
3
4
5
6
Numeric keys
(Select tracks)
1
2
3
4
5
6
TV
TV
VCR
VCR
7
0
MENU
SET UP
8
9
+10
RETURN
LSTN M.
OSD
SOUND
7
8
9
0
+10
RETURN
LSTN M.
DVD
CABLE
DSS
MENU
SET UP
OSD
SOUND
DSS
POWER
POWER
P.CALL
1 (Search)
¡ (Search)
DISC SKIP
¢ (Skip up)
MULTI CONTROL
TUNING
B.BOOST
RECEIVER
TITLE
AUX
ENTER
A/B+100
DISC SKIP
AUTO
TV SEL.
CD/DVD
INPUT SEL.
TUNER
¢ (Skip up)
MULTI CONTROL
1 (Search)
¡ (Search)
TUNING
B.BOOST
RECEIVER
TITLE
PHONO
DISC SKIP
MD/TAPE
CHANNEL
DISC SEL.
CINE.EQ
VIDEO2
MUTE
6 (3 Play/Pause)
7 (Stop)
4 (Skip down)
DVD
DVD
VIDEO1
BAND
P.CALL
P.CALL
P.CALL
4 (Skip down)
DVD
CABLE
ENTER
A/B+100
DISC SKIP
AUTO
TV SEL.
CD/DVD
INPUT SEL.
TUNER
AV AUX
RC-R0617
MD/TAPE
DISC SEL.
CINE.EQ
VIDEO2
MUTE
VOLUME
6 (3 Play/Pause)
7 (Stop)
DVD
DVD
VIDEO1
BAND
CHANNEL
AV AUX
VOLUME
RC-R0615
MD recorder operation keys
POWER
POWER
1
2
3
4
5
6
7
8
9
0
+10
RETURN
LSTN M.
Numeric keys
(Select tracks)
1
2
3
4
5
6
7
8
9
0
+10
RETURN
LSTN M.
TV
TV
VCR
VCR
MENU
SET UP
OSD
SOUND
DVD
CABLE
DSS
MENU
SET UP
OSD
SOUND
1 (Search)
¡ (Search)
+100 (Select tracks)
¢ (Skip up)
MULTI CONTROL
TUNING
B.BOOST
RECEIVER
TITLE
AUX
MUTE
ENTER
A/B+100
DISC SKIP
AUTO
TV SEL.
CD/DVD
INPUT SEL.
TUNER
DVD
VIDEO1
P.CALL
P.CALL
4 (Skip down)
VIDEO2
BAND
6 (3 Play)
7 (Stop)
1 (Search)
¡ (Search)
+100 (Select tracks)
MD/TAPE
VOLUME
TUNING
B.BOOST
RECEIVER
TITLE
PHONO
MUTE
35
ENTER
A/B+100
DISC SKIP
AUTO
TV SEL.
CD/DVD
INPUT SEL.
TUNER
DVD
VIDEO1
RC-R0617
_4942/32-44/EN
¢ (Skip up)
MULTI CONTROL
CHANNEL
AV AUX
P.CALL
4 (Skip down)
DVD
DISC SEL.
CINE.EQ
DSS
POWER
POWER
P.CALL
DVD
CABLE
VIDEO2
BAND
DVD
DISC SEL.
CINE.EQ
MD/TAPE
CHANNEL
AV AUX
VOLUME
RC-R0615
3/16/01, 3:11 PM
6 (3 Play)
7 (Stop)
Remote Control
Numeric keys
(Select tracks)
Basic remote control operations for other components
Other components' operations (For VR-506/517/KRF-V6050D/V555OD)
36
Refer to the following for the type of remote control operations available for each component.
1
Select the input source.
2
Press the keys corresponding to the operations you desire.
Refer to the following sections for details.
• When pressing keys in succession, press each key firmly and be sure to wait at least 1 second
before pressing the next key.
• Numeric keys function the same as the numeric keys on the original remote.
These keys can be used to perform the basic operations of KENWOOD and other
makers' components which the setup code for each component had been entered
beforehand.
⁄
TV operation keys
POWER
POWER
Numeric keys
1
2
3
4
5
6
7
8
9
Numeric keys
1
2
3
4
5
6
7
8
9
0
+10
RETURN
LSTN M.
MENU
SET UP
OSD
SOUND
TV
TV
VCR
VCR
0
+10
MENU
SET UP
OSD
SOUND
DVD
RETURN
LSTN M.
CABLE
DSS
POWER
P.CALL
P.CALL
P.CALL
MULTI CONTROL
MULTI CONTROL
TUNING
TV SEL. (TV Selector)
B.BOOST
RECEIVER
TITLE
AUX
ENTER
A/B+100
DISC SKIP
AUTO
TV SEL.
CD/DVD
INPUT SEL.
TUNER
DVD
VIDEO1
VIDEO2
CABLE
DSS
POWER
P.CALL
DVD
BAND
ENTER (Enter)
TUNING
DVD
DISC SEL.
CINE.EQ
INPUT SEL. (Input Selector)
TV SEL. (TV Selector)
MD/TAPE
B.BOOST
RECEIVER
TITLE
PHONO
CHANNEL
A/B+100
DISC SKIP
AUTO
TV SEL.
CD/DVD
INPUT SEL.
TUNER
DVD
VIDEO1
AV AUX
ENTER
VIDEO2
ENTER (Enter)
BAND
DVD
DISC SEL.
CINE.EQ
INPUT SEL. (Input Selector)
MD/TAPE
CHANNEL
AV AUX
MUTE
MUTE
MUTE
VOLUME
MUTE
VOLUME
Remote Control
RC-R0617
RC-R0615
Continued to next page
_4942/32-44/EN
36
3/16/01, 3:11 PM
Basic remote control operations for other components
VCR operation keys
37
POWER
Numeric keys
1
2
3
4
5
6
POWER
Numeric keys
1
2
3
4
5
6
TV
TV
VCR
7
8
9
0
+10
RETURN
LSTN M.
MENU
SET UP
OSD
SOUND
VCR
7
8
9
0
+10
RETURN
LSTN M.
DVD
CABLE
DSS
MENU
SET UP
OSD
SOUND
DSS
POWER
P.CALL
POWER
P.CALL
P.CALL
P.CALL
MULTI CONTROL
1 (Rewind)
¡ (Fast forward)
TUNING
BAND
AUTO
DVD
TV SEL.
CD/DVD
INPUT SEL.
TUNER
DVD
VIDEO1
MULTI CONTROL
ENTER
A/B+100
DISC SKIP
B.BOOST
RECEIVER
TITLE
AUX
MUTE
6 (3 Play)
7 (Stop)
8 (Pause)
INPUT SEL. (Input Selector)
1 (Rewind)
¡ (Fast forward)
TUNING
B.BOOST
RECEIVER
TITLE
PHONO
MD/TAPE
CHANNEL
DISC SEL.
CINE.EQ
VIDEO2
DVD
CABLE
ENTER
A/B+100
DISC SKIP
TV SEL.
CD/DVD
DVD
AV AUX
VIDEO1
VOLUME
VIDEO2
MUTE
BAND
AUTO
DVD
INPUT SEL.
TUNER
6 (3 Play)
7 (Stop)
8 (Pause)
INPUT SEL. (Input Selector)
MD/TAPE
CHANNEL
DISC SEL.
CINE.EQ
AV AUX
VOLUME
RC-R0617
RC-R0615
DVD player operation keys
POWER
1
2
3
4
5
6
7
8
9
POWER
Numeric keys
(Select tracks)
TV
1
2
3
4
5
6
7
8
9
0
+10
RETURN
LSTN M.
MENU
SET UP
OSD
SOUND
TV
VCR
RETURN (Return)
MENU (Menu)
OSD (OSD menu)
0
+10
MENU
SET UP
OSD
SOUND
RETURN
LSTN M.
CABLE
DSS
POWER
P.CALL
P.CALL
MULTI CONTROL
1 (Search)
¡ (Search)
TITLE (Title)
4 (Skip down)
¢ (Skip up)
TUNING
B.BOOST
RECEIVER
TITLE
AUX
MUTE
ENTER
A/B+100
DISC SKIP
AUTO
TV SEL.
CD/DVD
INPUT SEL.
TUNER
DVD
VIDEO1
VIDEO2
_4942/32-44/EN
BAND
DVD
DISC SEL.
CINE.EQ
VOLUME
RC-R0617
37
VCR
DVD
MD/TAPE
CHANNEL
AV AUX
%(Cursor »)
fi(Cursor «)
#(Cursor \)
@(Cursor |)
ENTER (Enter)
6 (3 Play)
7 (Stop)
8 (Pause)
RETURN (Return)
MENU (Menu)
OSD (OSD menu)
DVD
CABLE
DSS
POWER
P.CALL
P.CALL
MULTI CONTROL
1 (Search)
¡ (Search)
TITLE (Title)
4 (Skip down)
¢ (Skip up)
TUNING
B.BOOST
RECEIVER
TITLE
PHONO
A/B+100
DISC SKIP
AUTO
TV SEL.
CD/DVD
INPUT SEL.
TUNER
DVD
VIDEO1
MUTE
ENTER
VIDEO2
BAND
DVD
DISC SEL.
CINE.EQ
MD/TAPE
CHANNEL
AV AUX
VOLUME
RC-R0615
3/16/01, 3:11 PM
%(Cursor »)
fi(Cursor «)
@(Cursor |)
#(Cursor \)
ENTER (Enter)
6 (3 Play)
7 (Stop)
8 (Pause)
Remote Control
Numeric keys
(Select tracks)
Basic remote control operations for other components
38
DSS receiver operation keys
POWER
Numeric keys
1
2
3
4
5
6
POWER
Numeric keys
1
2
3
4
5
6
TV
TV
VCR
MENU (Menu)
OSD (OSD menu)
7
8
9
0
+10
RETURN
LSTN M.
MENU
SET UP
OSD
SOUND
7
CABLE
POWER
P.CALL
MULTI CONTROL
TUNING
B.BOOST
RECEIVER
TITLE
AUX
ENTER
BAND
A/B+100
DISC SKIP
AUTO
TV SEL.
CD/DVD
INPUT SEL.
TUNER
DVD
VIDEO1
VIDEO2
MUTE
8
9
0
+10
RETURN
LSTN M.
MENU
SET UP
OSD
SOUND
DVD
DSS
P.CALL
VCR
%(Cursor »)
fi(Cursor «)
#(Cursor \)
@(Cursor |)
MENU (Menu)
OSD (OSD menu)
CABLE
DSS
POWER
P.CALL
P.CALL
MULTI CONTROL
ENTER (Enter)
TUNING
DVD
B.BOOST
RECEIVER
TITLE
PHONO
MD/TAPE
CHANNEL
DISC SEL.
CINE.EQ
DVD
ENTER
A/B+100
DISC SKIP
AUTO
TV SEL.
CD/DVD
INPUT SEL.
TUNER
DVD
AV AUX
VIDEO1
VOLUME
VIDEO2
MUTE
BAND
%(Cursor »)
fi(Cursor «)
@(Cursor |)
#(Cursor \)
ENTER (Enter)
DVD
MD/TAPE
CHANNEL
DISC SEL.
CINE.EQ
AV AUX
VOLUME
RC-R0617
RC-R0615
Cable tuner operation keys
POWER
1
2
3
4
5
6
POWER
1
2
3
4
5
6
7
8
9
0
+10
RETURN
LSTN M.
TV
TV
Remote Control
VCR
7
8
0
+10
MENU
SET UP
OSD
SOUND
VCR
9
DVD
RETURN
LSTN M.
MENU
SET UP
POWER
P.CALL
TUNING
B.BOOST
RECEIVER
TITLE
AUX
AUTO
TV SEL.
CD/DVD
INPUT SEL.
TUNER
DVD
VIDEO1
MUTE
VIDEO2
BAND
DVD
DISC SEL.
CINE.EQ
MD/TAPE
VOLUME
38
P.CALL
BAND
AUTO
AV AUX
T (P. CALL +)
MULTI CONTROL
Tuning
TUNING
B.BOOST
RECEIVER
TITLE
PHONO
ENTER
A/B+100
DISC SKIP
AUTO
TV SEL.
CD/DVD
INPUT SEL.
TUNER
DVD
VIDEO1
VIDEO2
MUTE
BAND
DVD
CHANNEL
RC-R0617
_4942/32-44/EN
DSS
P.CALL
T (P. CALL +)
ENTER
A/B+100
DISC SKIP
OSD
SOUND
CABLE
POWER
P.CALL
MULTI CONTROL
Tuning
DVD
CABLE
DSS
DISC SEL.
CINE.EQ
MD/TAPE
CHANNEL
AV AUX
VOLUME
RC-R0615
3/16/01, 3:11 PM
BAND
AUTO
In case of difficulty
Resetting the Microcomputer
The microcomputer may malfunction (unit cannot be operated,
or shows an erroneous display) if the power cord is unplugged
while the power is ON, or due to some other external factor. If this
happens, execute the following procedure to reset the microcomputer and return the unit to its normal operating condition.
39
For U.S.A. and Canada
Unplug the power cord from the wall outlet, then plug it
back in while holding down the POWER key.
For other countries
With the power cord plugged in, turn the POWER key
OFF. Then, while holding down the ON/STANDBY key,
press POWER.
• Please note that resetting the microcomputer will clear the contents
of the memory and returns the unit to the state it was in when it left the
factory.
Amplifier
Symptom
Remedy
Cause
No sound from the speakers.
• Connect them properly referring to “Connecting
the speakers”
&
• Adjust the volume to a proper level.
• Turn OFF the MUTE.
™
• Set the SPEAKERS switch(es) to ON. )
• The speaker cords are disconnected.
• VOLUME is set to the minimum position.
• MUTE is ON.
• The SPEAKERS switches are set to OFF.
The standby indicator blinks and sound is
not output.
• Speaker cords are short-circuited.
• Turn the power off, eliminate the short-circuiting, then turn on the power again.
Sound is not output from one of the speakers.
• The speaker cord is disconnected.
• Connect it properly referring to “Connecting the
speakers”.
&
Sound is not output from the surround
speakers and / or the center speaker, or their
sound is very small.
• The surround speaker cords and/or the center
speaker cord is disconnected.
• A surround mode has not been engaged.
• The surround and/or center volume controls are
set to the minimum level.
• Connect it properly referring to “Connecting the
speakers”.
&
• Select a surround mode.
• Adjust the speaker levels using the test tone.
(
A humming noise is generated when the
PHONO input selector is selected.
• The audio cord from the turntable is not connected to the PHONO jacks.
• The turntable is not grounded.
• Insert the audio cord plugs securely into the
PHONO jacks.
• Connect the grounding wire to the GND terminal on the rear panel.
When playing a Dolby Digital source signal
using a DVD player, the sound is cut off soon
after it starts.
• There are many possible causes for this problem, depending on the type of DVD player used.
• Set the input mode to digital manual before
starting playback of the Dolby Digital source.
9
No sound is produced during playback from
a DVD player.
• The input mode is set to digital manual.
• Press the INPUT MODE key to select to digital
auto mode.
9
A video source cannot be recorded
normally.
• The software is copy-guarded.
• Copy-guarded video software cannot be recorded.
Tuner
Cause
Remedy
Radio stations cannot be received.
• No antenna is connected.
• The broadcast band is not set properly.
• The frequency of the desired station is not
tuned.
• Connect an antenna.
$
• Set the broadcast band properly.
• Tune the frequency of the desired station.
£
Interference.
• Noise due to ignition noise from an automobile.
• Noise due to interference from an electric appliance.
• Noise due to a nearby TV set.
• Install the outdoor antenna away from the road.
• Turn off the power to the appliance.
• The preset station belongs to a frequency that
cannot be received.
• The preset memory was cleared because the
power cord had been unplugged for a long
period of time.
• Preset a station with a receivable frequency.
A station which was preset cannot be received by pressing the corresponding numeric key.
_4942/32-44/EN
39
• Install the receiver farther away from the TV.
• Preset the station again.
3/16/01, 3:11 PM
Additional Information
Symptom
In case of difficulty
Remote control unit
40
Symptom
Cause
Remedy
Certain inputs cannot be selected using the
remote control.
• No setup codes registered at for the respective
input(s).
• Register a setup code at the respective input(s).
º
Remote control operation is not possible.
• The remote control is set to a different operation
mode.
• Batteries are exhausted.
• The remote control unit is too far away from the
main system, controlling angle is too large, or
there is an obstacle between the receiver and
the remote.
• The audio cords and system control cords are
not connected properly.
• No software is loaded in the source component.
• Press the source select keys or source POWER
keys to select the appropriate operation mode.
• Replace with new batteries.
• Operate the remote control unit within the controllable range.
• An attempt is made to play a tape which is being
recorded in the cassette deck.
• The remote control has not been set to the
operation mode for the component you wish to
control.
• The microprocessor of the remote control malfunctions.
• Connect properly referring to “Setting up the
system”.
• Place software in the source component you
want to play.
• Wait until recording has completed.
• Press the source select keys or source POWER
keys to activate the operation mode for the
component you want to control before operation.
ª
• Reset the microprocessor.
Additional Information
_4942/32-44/EN
40
3/16/01, 3:11 PM
Specifications
Caution : Read this page carefully to ensure safe
operation.
For U.S.A and Canada
41
AUDIO section (VR-506)
Rated power output during STEREO operation
100 watts per channel minimum RMS, both channels driven, at
8 Ω from 40Hz to 20 kHz with no more than 0.7% total harmonic
distortion. (FTC)
DIGITAL AUDIO section
Sampling frequency ...................... 32 kHz, 44.1 kHz, 48 kHz, 96kHz
Input level / impedance / wave length
Optical ........................... (–15 dBm ~ –21 dBm), 660 nm ±30nm
Coaxial ................................................................. 0.5 Vp-p / 75 Ω
Effective power output during SURROUND operation
FRONT (40-20kHz, 0.7% T.H.D. at 8 Ω one channel driven)
.............................................................................. 100 W + 100 W
CENTER (40-20kHz, 0.7% T.H.D. at 8 Ω one channel driven)
............................................................................................. 100 W
SURROUND (40-20kHz, 0.7% T.H.D. at 8 Ω one channel
driven) .................................................................. 100 W + 100 W
Total harmonic distortion ......................... 0.050% (1 kHz, 50W, 8 Ω)
Frequency response
CD ............................................. 10 Hz ~ 60 kHz, +0 dB, –3.0 dB
Signal to noise ratio (IHF’66)
PHONO (MM) ........................................................................ 74 dB
CD ......................................................................................... 90 dB
Input sensitivity / impedance
PHONO (MM) ......................................................... 2.5 mV / 27 kΩ
CD ......................................................................... 200 mV / 47 kΩ
MONITOR IN (VIDEO2/MONITOR) ..................... 200 mV / 47 kΩ
DVD/6ch INPUT ................................................... 200 mV / 47 kΩ
Output level / impedance
TAPE REC .............................................................. 200 mV / 1 kΩ
MONITOR OUT (VIDEO2/MONITOR) ................... 200 mV / 1 kΩ
PRE OUT (SUBWOOFER) ...................................... 1.5 V / 2.2 kΩ
Tone control
BASS ................................................................ ±10 dB (at 70 Hz)
TREBLE .......................................................... ±10 dB (at 10 kHz)
VIDEO section
AUDIO section (VR-505/517)
AM tuner section
Rated power output during STEREO operation
Tuning frequency range
10 kHz step ................................................. 530 kHz ~ 1,700 kHz
Usable sensitivity (30% mod., S/N 20 dB) ......... 16 µV / (600 µV/m)
Signal to noise ratio (30% mod. 1 mV input) ........................... 50 dB
100 watts per channel minimum RMS, both channels driven, at
8 Ω from 40 Hz to 20 kHz with no more than 0.7% total harmonic
distortion. (FTC)
VIDEO inputs / outputs
VIDEO (composite) ................................................. 1 Vp-p / 75 Ω
S VIDEO inputs / outputs (VR-506/517)
S VIDEO (luminance signal) .................................. 1 Vp-p / 75 Ω
S VIDEO (chrominance signal) ....................... 0.286 Vp-p / 75 Ω
FM tuner section
Tuning frequency range ................................... 87.5 MHz ~ 108 MHz
Usable sensitivity (MONO)
................ 1.3 µV (75 Ω)/ 13.2 dBf (75 kHz DEV., SINAD 30 dB)
50dB quieting sensitivity
STEREO ................................................... 28 µV (75 Ω)/ 40.2 dBf
Total harmonic distortion (1 kHz)
MONO ........................................................ 0.5% (71.2 dBf input)
STEREO .................................................... 0.7% (71.2 dBf input)
Signal to noise ratio (1 kHz, 75 kHz DEV.)
MONO ....................................................... 75 dB (71.2 dBf input)
STEREO ................................................... 68 dB (71.2 dBf input)
Stereo separation (1 kHz) .......................................................... 40 dB
Selectivity (±400 kHz) ................................................................. 70 dB
Frequency response ................. (30 Hz ~ 15kHz), +0.5 dB, –3.0 dB
GENERAL
Power consumption ................................................................... 2.6 A
AC outlet
SWITCHED ....................................... (total 150 W, 1.25 A max.)
Dimensions ..................................................... W : 440 mm (17-5/16")
H : 143 mm (5-11/16")
D : 400 mm (15-3/8")
Weight (Net)
VR-506/517 ......................................................... 8.8 kg (18.92 lb)
VR-505 ................................................................ 8.7 kg (18.89 lb)
Notes
1. KENWOOD follows a policy of continuous advancements in development. For this reason specifications may be changed without notice.
2. The full performance may not be exhibited in an extremely cold location (under a water-freezing temperature).
_4942/32-44/EN
41
3/16/01, 3:11 PM
Additional Information
Effective power output during SURROUND operation
FRONT (40-20kHz, 0.7% T.H.D. at 8 Ω one channel driven)
.............................................................................. 100 W + 100 W
CENTER (40-20kHz, 0.7% T.H.D. at 8 Ω one channel driven)
............................................................................................. 100 W
SURROUND (40-20kHz, 0.7% T.H.D. at 8 Ω one channel
driven) .................................................................. 100 W + 100 W
Total harmonic distortion ......................... 0.050% (1 kHz, 50W, 8 Ω)
Frequency response
CD ............................................. 10 Hz ~ 60 kHz, +0 dB, –3.0 dB
Signal to noise ratio (IHF’66)
CD ......................................................................................... 90 dB
Input sensitivity / impedance
CD ......................................................................... 200 mV / 47 kΩ
MONITOR IN (VIDEO2/MONITOR) ..................... 200 mV / 47 kΩ
PHONO (MM) (VR-517) ......................................... 2.5 mV / 27 kΩ
DVD/6ch INPUT (VR-517) ................................... 200 mV / 47 kΩ
Output level / impedance
TAPE REC .............................................................. 200 mV / 1 kΩ
MONITOR OUT (VIDEO2/MONITOR) ................... 200 mV / 1 kΩ
PRE OUT (SUBWOOFER) (VR-505) ...................... 1.5 V / 2.2 kΩ
Tone control
BASS ................................................................ ±10 dB (at 70 Hz)
TREBLE .......................................................... ±10 dB (at 10 kHz)
Caution : Read this page carefully to ensure safe
operation.
Specifications
For other countries
42
AUDIO section (KRF-V6050D)
AUDIO section (KRF-V5550D)
Effective power output during STEREO operation
1kHz,10% T.H.D.,at 8 Ω ........................................... 140 W + 140 W
Rated power output during STEREO operation
Effective power output during SURROUND operation
(1kHz, 10%, 8Ω) ........................................................... 110 W + 110 W
Rated power output during STEREO operation
100 watts per channel minimum RMS, both channels driven, at
8 Ω from 40 Hz to 20 kHz with no more than 0.7% total harmonic
distortion.(FTC)
Effective power output during SURROUND operation
FRONT (1kHz, 10% T.H.D. at 8 Ω one channel driven)
.............................................................................. 140 W + 140 W
CENTER (1kHz, 10% T.H.D. at 8 Ω one channel driven)
............................................................................................. 140 W
SURROUND (1kHz, 10% T.H.D. at 8 Ω one channel driven)
.............................................................................. 140 W + 140 W
Total harmonic distortion ......................... 0.050% (1 kHz, 50W, 8 Ω)
Frequency response
CD ............................................. 10 Hz ~ 60 kHz, +0 dB, –3.0 dB
Signal to noise ratio (IHF’66)
PHONO (MM) ........................................................................ 74 dB
CD ......................................................................................... 90 dB
Input sensitivity / impedance
PHONO (MM) ......................................................... 2.5 mV / 27 kΩ
CD ......................................................................... 200 mV / 47 kΩ
VIDEO2/MONITOR ............................................... 200 mV / 47 kΩ
DVD/6ch INPUT ................................................... 200 mV / 47 kΩ
Output level / impedance
TAPE REC .............................................................. 200 mV / 1 kΩ
VIDEO2/MONITOR ................................................. 200 mV / 1 kΩ
PRE OUT (SUBWOOFER) ...................................... 1.5 V / 2.2 kΩ
Tone control
BASS ................................................................ ±10 dB (at 70 Hz)
TREBLE .......................................................... ±10 dB (at 10 kHz)
AUDIO section (KRF-V5050D)
Effective power output during STEREO operation
(1 kHz, 10%, 8Ω) .......................................................... 140 W + 140 W
Rated power output during STEREO operation
100 watts channel minimum RMS, both channels driven, at 8
Ω from 40 Hz to 20 kHz with no more than 0.7% total harmonic
distortion. (FTC)
Effective power output during SURROUND operation
FRONT (1kHz, 10% T.H.D. at 8 Ω one channel driven)
.............................................................................. 140 W + 140 W
CENTER (1kHz, 10% T.H.D. at 8 Ω one channel driven)
............................................................................................. 140 W
SURROUND (1kHz, 10% T.H.D. at 8 Ω one channel driven)
.............................................................................. 140 W + 140 W
Total harmonic distortion ......................... 0.050% (1 kHz, 50W, 8 Ω)
Frequency response
CD ............................................. 10 Hz ~ 60 kHz, +0 dB, –3.0 dB
Signal to noise ratio (IHF’66)
PHONO (MM) ........................................................................ 74 dB
CD, TUNER, AUX, TAPE ..................................................... 90 dB
Input sensitivity / impedance
PHONO (MM) ......................................................... 2.5 mV / 27 kΩ
CD ......................................................................... 200 mV / 47 kΩ
MONITOR IN (VIDEO2/MONITOR) ..................... 200 mV / 47 kΩ
DVD/6ch INPUT ................................................... 200 mV / 10 kΩ
Output level / impedance
TAPE REC .............................................................. 200 mV / 1 kΩ
MONITOR OUT (VIDEO2/MONITOR) ................... 200 mV / 1 kΩ
PRE OUT (SUBWOOFER) ...................................... 1.5 V / 2.2 kΩ
Tone control
BASS ................................................................ ±10 dB (at 70 Hz)
TREBLE .......................................................... ±10 dB (at 10 kHz)
80 watts per channel minimum RMS, both channels driven, at
8 Ω from 40 Hz to 20 kHz with no more than 0.7% total
harmonic distortion. (FTC)
Effective power output during SURROUND operation
FRONT (1kHz, 10% T.H.D. at 8 Ω one channel driven)
.............................................................................. 130 W + 130 W
CENTER (1kHz, 10% T.H.D. at 8 Ω one channel driven)
............................................................................................. 130 W
SURROUND (1kHz, 10% T.H.D. at 8 Ω one channel driven)
.............................................................................. 130 W + 130 W
Total harmonic distortion ......................... 0.050% (1 kHz, 40W, 8 Ω)
Frequency response
CD ............................................. 10 Hz ~ 60 kHz, +0 dB, –3.0 dB
Signal to noise ratio (IHF’66)
CD, TUNER, AUX, TAPE ..................................................... 90 dB
Input sensitivity / impedance
CD ......................................................................... 200 mV / 47 kΩ
MONITOR IN (VIDEO2/MONITOR) ..................... 200 mV / 47 kΩ
Output level / impedance
TAPE REC .............................................................. 200 mV / 1 kΩ
MONITOR OUT (VIDEO2/MONITOR) ................... 200 mV / 1 kΩ
Tone control
BASS ................................................................ ±10 dB (at 70 Hz)
TREBLE .......................................................... ±10 dB (at 10 kHz)
DIGITAL AUDIO section
Sampling frequency ...................... 32 kHz, 44.1 kHz, 48 kHz, 96kHz
Input level / impedance / wave length
Optical ........................... (–15 dBm ~ –21 dBm), 660 nm ±30nm
Coaxial ................................................................. 0.5 Vp-p / 75 Ω
VIDEO section
VIDEO inputs / outputs
VIDEO (composite) ................................................ 1 Vp-p / 75 Ω
S VIDEO inputs / outputs (KRF-V6050D)
S VIDEO (luminance signal) ................................. 1 Vp-p / 75 Ω
S VIDEO (chrominance signal) ...................... 0.286 Vp-p / 75 Ω
FM tuner section
Tuning frequency range ................................... 87.5 MHz ~ 108 MHz
Usable sensitivity (MONO)
................ 1.6 µV (75 Ω)/ 15.2 dBf (75 kHz DEV., SINAD 30 dB)
50dB quieting sensitivity
STEREO ................................................... 28 µV (75 Ω)/ 40.2 dBf
Total harmonic distortion (1 kHz)
MONO ........................................................ 0.5% (71.2 dBf input)
STEREO .................................................... 0.7% (71.2 dBf input)
Signal to noise ratio (1 kHz, 75 kHz DEV.)
MONO ....................................................... 75 dB (71.2 dBf input)
STEREO ................................................... 68 dB (71.2 dBf input)
Stereo separation (1 kHz) .......................................................... 40 dB
Selectivity (±400 kHz) ................................................................. 50 dB
Frequency response ................. (30 Hz ~ 15kHz), +0.5 dB, –3.0 dB
AM tuner section
Tuning frequency range
9 kHz step ................................................... 531 kHz ~ 1,602 kHz
10 kHz step ................................................. 530 kHz ~ 1,610 kHz
Usable sensitivity ................................................. 16 µV / (600 µV/m)
Signal to noise ratio (30% mod. 1 mV input) ........................... 50 dB
Additional Information
Notes
1. KENWOOD follows a policy of continuous advancements in development. For this reason specifications may be changed without notice.
2. The full performance may not be exhibited in an extremely cold location (under a water-freezing temperature).
_4942/32-44/EN
42
3/16/01, 3:11 PM
Caution : Read this page carefully to ensure safe
operation.
Specifications
GENERAL
Power consumption
KRF-V6050D/V5050D ......................................................... 270 W
KRF-V5550D ....................................................................... 200 W
AC outlet
SWITCHED ...................................................... (total 90 W max.)
Dimensions ...................................................................... W : 440 mm
H : 143 mm
D : 400 mm
Weight (Net)
(KRF-V6050D/V5050D) ....................................................... 9.3 kg
(KRF-V5550D) .................................................................... 8.4 kg
Additional Information
43
_4942/32-44/EN
43
3/16/01, 3:11 PM
For your records
Record the serial number, found on the back of the unit, in the spaces
designated on the warranty card, and in the space provided below. Refer
to the model and serial numbers whenever you call upon your dealer for
information or service on this product.
Model __________________ Serial Number ________________________
_4942/32-44/EN
44
3/16/01, 3:11 PM
Download PDF

advertising