Specifications | Black Box 3D HDMI Fiber Extender TV Video Accessories User Manual

ACS1009A-xx
ACS2209A-xx
ACS4001A-xx
ACS4201A-xx
DVI-D-Fibre-KVM-Extender
SingleHead and DualHead
Manual
http://www.blackbox.com
DVI-D FIBRE KVM-EXTENDER
Welcome to the DVI-D Fibre KVM-Extender
Family!
Thank you for purchasing an DVI-D Fibre KVM-Extender! We appreciate your business, and
we think you’ll appreciate the many ways that your enhanced RGB Graphic system will save
you money, time, and effort.
That’s because our DVI-D Fibre KVM-Extender is all about breaking away from the
traditional model of attaching a new display to DVI graphic source. Using the DVI-D Fibre
KVM-Extender, you can remotely locate monitor, keyboard and mouse up to 10km away
from your CPU.
Wherever long distances are usual, e.g. airports, industrial plants, call- centres or in
distributed computer centres, the DVI-D Fibre KVM-Extender is the best way, to solve all
problems in remotely locating your console. 8 different types are available: Singlehead and
Dualhead devices for PS2 keyboard/mouse and Singlehead and Dualhead devices for USB
keyboard/mouse – all types either for Singlemode or Multimode fibres.
This manual will tell you all about your new DVI-D Fibre KVM-Extender, including how to
install, operate, and troubleshoot it. For an introduction to the Converter, see Chapter 2. The
Converter product codes covered in this manual are:
ACS1009A-MM: KVM-Extender Singlehead DVI-D, PS2-K/M – Multimode Fibres
ACS2209A-MM: KVM-Extender Dualhead DVI-D, PS2- K/M – Multimode Fibres
ACS4001A-MM: KVM-Extender Singlehead DVI-D, USB- K/M – Multimode Fibres
ACS4201A-MM: KVM-Extender Dualhead DVI-D, USB- K/M – Multimode Fibres
ACS1009A-SM: KVM-Extender Singlehead DVI-D, PS2-K/M – Singlemode Fibres
ACS2209A-SM: KVM-Extender Dualhead DVI-D, PS2- K/M – Singlemode Fibres
ACS4001A-SM: KVM-Extender Singlehead DVI-D, USB- K/M – Singlemode
Fibres
ACS4201A-SM: KVM-Extender Dualhead DVI-D, USB- K/M – Singlemode Fibres
2
DVI-D FIBRE KVM-EXTENDER
Copyrights and Trademarks
©2007. All rights reserved. This information may not be reproduced in any manner without
the prior written consent of the manufacturer.
Information in this document is subject to change without notice and the manufacturer shall
not be liable for any direct, indirect, special, incidental or consequential damages in
connection with the use of this material.
All trademark and trade names mentioned in this document are acknowledged to be the
property of their respective owners.
Disclaimer
While every precaution has been taken in the preparation of this manual, the manufacturer
assumes no responsibility for errors or omissions. Neither does the manufacturer assume any
liability for damages resulting from the use of the information contained herein. The
manufacturer reserves the right to change the specifications, functions, or circuitry of the
product without notice.
The manufacturer cannot accept liability for damage due to misuse of the product or due to
any other circumstances outside the manufacturer’s control (whether environmental or
installation related). The manufacturer shall not be responsible for any loss, damage, or injury
arising directly, indirectly, or consequently from the use of this product.
Cautions and Notes
The following symbols are used in this guide:
CAUTION. This indicates an important operating instruction
that should be followed to avoid any potential damage to
hardware or property, loss of data, or personal injury.
NOTE. This indicates important information to help you make the best use of
this product.
3
DVI-D FIBRE KVM-EXTENDER
.
4
DECLARATION OF CONFORMITY
EUROPEAN UNION DECLARATION OF CONFORMITY
This is to certify that, when installed and used according to the instructions in this
manual, together with the specified cables and the maximum cable length <3m, the
Units:
ACS1009A-MM, ACS2209A-MM
ACS4001A-MM, ACS4201A-MM
ACS1009A-SM, ACS2209A-SM
ACS4001A-SM, ACS4201A-SM
are shielded against the generation of radio interferences in accordance with the
application of Council Directive 89/336/EEC as well as these standards:
EN 55022:
EN 55024:
IEC 61000-4-2:
IEC 61000-4-3:
IEC 61000-4-4:
EN 61000-3-2
EN 61000-3-3
1999
1999
2001
2001
2001
2001
2002
Class A
The device was tested in a typical configuration with PC.
This equipment has been found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
5
DVI-D FIBRE KVM-EXTENDER
Safety Precautions and Installation Guidelines
To ensure reliable and safe long-term operation, please note the following installation
guidelines:
•
Only use in dry, indoor environments.
•
If the building has 3-phase AC power, try to ensure that equipment connected to the
Local and Remote units is on the same phase.
•
The Remote unit, Local unit and any power supplies can get warm. Do not locate them
in an enclosed space without any airflow.
•
Do not place a power supply directly on top of a unit.
•
Do not obstruct a unit’s ventilation existing holes.
To safeguard against personal injury and avoid possible
damage to equipment or property, please observe the
following:
6
•
Only use power supplies originally supplied with the
product or manufacturer-approved replacements. Do not
attempt to dismantle or repair any power supply. Do not
use a power supply if it appears to be defective or has a
damaged case.
•
Connect all power supplies to grounded outlets. In each
case, ensure that the ground connection is maintained
from the outlet socket through to the power supply’s AC
power input.
•
Do not attempt to modify or repair this product, or make
a connection from the Fibre link interface (LC) to any
other products, especially telecommunications or
network equipment.
TABLE OF CONTENTS
Contents
1. Quick Setup
8
2. Overview
9
2.1
2.2
2.3
2.4
2.5
2.6
Introduction
Glossary
Features
Product Range
Compatibility
How to Use This Guide
3. Installation
3.1
3.2
3.3
3.4
Package Contents
Interconnection Cable Requirements
System Setup
Diagnostic LEDs
9
9
11
12
13
13
15
15
16
17
24
4. Troubleshooting
25
Appendix A: Example Applications
27
Appendix B: Rack Mount Options
29
Appendix D: Calling Technical Support
31
Appendix E: Specifications
33
Appendix F: Connectors
35
7
DVI-D FIBRE KVM-EXTENDER
1. Quick Setup
This section briefly describes how to install your KVM extender system. Unless you are an
experienced user, we recommend that you follow the full procedures described in the rest of
this manual.
Install system
1.
2.
3.
4.
Connect Remote unit to KVM.
Connect Local unit to CPU or switch.
Connect Local and Remote units with matching interconnection cable
(Fibre).
Power up the system.
NO
Power LED
illuminated?
YES
Link LED
illuminated ?
NO
Check the Fibre cable, and
Fibre connectors
YES
Video OK
LED ?
illuminated ?
YES
Done
8
Check p.s.u.’s and connection
to power outlet
NO
Check settings of graphic card
or boot CPU
OVERVIEW
2.
Overview
2.1
Introduction
A Fibre KVM Extender is mainly used, to extend the maximum distance between a CPU
and his Keyboard / Monitor / Mouse considerably. In addition they are irrecoverable in
installations in electromagnetic hazardous environments (EMI). Normal Keyboard-/
Monitor-/ Mouse extender cables (and Extender using traditional cables) cannot go so far
and EMI interferences may reduce the maximum distance and/or reliability. Using a
DVI-D Fibre Extender system, these limitations are past. Remain your CPU in a secure
rack cabinet or data center while accessing from a 10km remotely located place.
A basic KVM extension system comprises a Local unit (transmitter) and a Remote unit
(receiver). The Local unit connects directly to the computer (or a KVM switch system) using
the supplied cable(s). The user console (keyboard, mouse and monitor) attaches to the
Remote unit. The Remote and Local units communicate video and data information along the
interconnecting cable. Local units offer dual access, allowing the connection of a second user
console close to the computer.
2.2
Glossary
The following terms are used in this guide:
Fibre
Singlemode or Multimode fibre cable.
Singlemode
9µ Singlemode-fibre cable
Mulitmode
62,5µ Multimode- or
50µ Multimode-fibre cable
KVM
Keyboard, Video and Mouse.
Console
Keyboard, Mouse and Monitor
Dual Access
A system allowing connection of Local and Remote user consoles.
Singlehead
An extender system that supports one monitor + Keyboard/Mouse
Dualhead
An extender system that supports two monitors + Keyboard/Mouse
DVI
Digital Video standard, installed by Digital Display Working Group
(www.ddwg.org) R, G, B, CLOCK in a data stream with up to
3x 1,6 Gbit/sec. Signals are TMDS Level.
PSU
The desktop power supply connected to the Local/Remote unit.
HID
Human Interface Devices are units, which are used for human access
to the CPU. They are a USB-device class of its own (e.g. Memory
Devices etc.). Besides of keyboard and mouse also touchscreen, light
pen, fingerprint sensor, graphic tablets etc. are HID devices
9
DVI-D FIBRE KVM-EXTENDER
CPU with DVI-D
Graphic card
Local Console
Optional
2. Monitor
DVI-D Fibre KVMExtender system
Remote Console
Optional
2. Monitor
DVI-D Fibre – KVM Extender system (example)
10
OVERVIEW
2.3
Features
All members of the DVI-D Fibre - DVI KVM Extender Series offer the following features:
•
Support for DVI-D Graphic cards (all devices)
•
Support for PS2-Keyboard and PS2-Mouse (ACS1009A-xx and ACS2209A-xx)
•
Support for USB-Keyboard and USB-Mouse (ACS4001A-xx and ACS4201A-xx)
Devices with USB- connectors do only support Keyboard and Mouse. It’s
possible, that other HDI devices (Human Device Interface) like TouchScreen, Graphic tablet, Barcode reader or similar are supported – but
there is no guarantee for this! The DVI-D Fibre KVM-Extender is NOT
suitable for use with other USB devices like Scanner, WEB- Cams, data
sticks etc.
The device never supports more than two devices – Keyboard and Mouse
or Keyboard and Touchscreen, etc. but not e.g. Keyboard, Mouse and
Touchscreen simultaneously. A Hub is allowed but does not rais the
number of supported devices
•
Maximum resolution: DVI-D: 1600x1200@60Hz over all allowed distances
all lower resolutions with refresh rates of at least 75Hz
•
Supporting 18 Bit color depth = 256,000 colors
•
Status indicator LEDs on each device.
•
Small footprint chassis.
•
Rack mount options available.
•
CPU cables + Adapters included.
11
DVI-D FIBRE KVM-EXTENDER
2.4
Product Range
There are four products in the range and various upgrade kits:
DVI-D Fibre - Extender
ACS1009A-MM
KVM-Extender 1x DVI, PS2-Keyboard, PS2-Mouse
(Singlehead), Multimode Fibres
ACS2209A-MM
KVM-Extender 2x DVI, PS2-Keyboard, PS2-Mouse s
(Dualhead), Multimode Fibres
ACS4001A-MM
KVM-Extender 1x DVI, USB-Keyboard, USB-Mouse
(Singlehead), Multimode Fibres
ACS4201A-MM
KVM-Extender 2x DVI, USB-Keyboard, USB-Mouse
(Dualhead), Multimode Fibres
ACS1009A-SM
KVM-Extender 1x DVI, PS2-Keyboard, PS2-Mouse
(Singlehead), Singlemode Fibres
ACS2209A-SM
KVM-Extender 2x DVI, PS2-Keyboard, PS2-Mouse s
(Dualhead), Singlemode Fibres
ACS4001A-SM
KVM-Extender 1x DVI, USB-Keyboard, USB-Mouse
(Singlehead), Singlemode Fibres
ACS4201A-SM
KVM-Extender 2x DVI, USB-Keyboard, USB-Mouse
(Dualhead), Singlemode Fibres
Upgrade Kits
ACS1009A-RMK
19”/1HE Rackmount- Kit to mount up to 4 Singlehead
devices
ACS2209A-RMK
19”/1HE Rackmount- Kit to mount up to 4 Dualhead
devices
ACS2209A-PS
19”/1U rackmountable P.S.U. Input: 100..240VAC/0.5A;
Output 5VDC/6A to source up to 3 units Singlehead or
Dualhead. Requires one unit space in RMK (ACS1009ARMK/ACS2209A-RMK)
ACS1009A-BP
Blanking Plate for Single Head Rackmountkit
ACS2209A-BP
Blanking Plate for Dual Head Rackmountkit
12
OVERVIEW
2.5
Compatibility
Interface Compatibility
•
Digital Video (DVI-D): Digital Video standard, installed by Digital Display Working
Group (www.ddwg.org) R, G, B, CLOCK in a data stream with up to
3x 1,6 Gbit/sec. Signals are TMDS Level.
•
PS/2 Keyboard: Compatible with all standard keyboards. Certain keyboards with
enhanced features may also be supported with custom firmware.
•
PS/2 Mouse: Compatible with all standard 2-button, 3-button and wheel mice.
•
USB Keyboard: Compatible with all standard keyboards. Certain keyboards with
enhanced features may also be supported with custom firmware. Keyboards with built-in
hub are also supported – but there are never more than two HDI devices supported.
•
USB Mouse: Compatible with all standard 2-button, 3-button and wheel mice.
Devices with USB- connectors do only support Keyboard and Mouse. It’s
possible, that other HDI devices (Human Device Interface) like TouchScreen, Graphic tablet, Barcode reader or similar are supported – but
there is no guarantee for this! The DVI-D Cat X KVM-Extender is NOT
suitable for use with other USB devices like Scanner, WEB- Cams, data
sticks etc.
The device never supports more than two devices – Keyboard and Mouse
or Keyboard and Touchscreen, etc. but not e.g. Keyboard, Mouse and
Touchscreen simultaneously. A Hub is allowed but does not rais the
number of supported devices
13
DVI-D FIBRE KVM-EXTENDER
2.6 How to Use This Guide
This guide describes the installation and configuration of the DVI-D Fibre – Extender Series.
Although the connection and operation of the system is relatively straightforward, you should
consider the following before getting started:
Connection & Compatibility
If you have purchased an Extender Kit, this will contain all the cables required to connect the
Local unit to your PC or KVM switch. Please see also: Package Contents (page 15)
For information about connection and installation, see page 17.
DDC Information
Normally it is not necessary to make any adjustments to the DVXi- Extender. However, in
some circumstances, it may be necessary to redefine the source of DDC Information for the
CPU. By default, the DVI-D Fibre KVM-Extender uses its own internal DDC table. If this
setting does not satisfy your requirements, the DDC table can either be switched to the locally
or remotely attached screen.
To modify the DDC-Setup, please ask Technical support for additional information.
Compatibility
Devices with PS2 connectors are NOT compatible to devices with USB connectors.
14
INSTALLATION
3. Installation
For first-time users, we recommend that you carry out a test placement, confined to a single
room, before commencing full installation. This will allow you to identify and solve any
cabling problems, and experiment with the KVM extender system more conveniently.
3.1 Package Contents
You should receive the following items in your extender package (all types):
•
DVI-D Fibre KVM-Extender- pair (Local Unit + Remote Unit)
•
2x 5V DC universal power supply for the DVI-D Fibre - Extender
•
2x German type power cord
•
User manual (Quick Setup)
ACS1009A-xx and ACS2209A-xx (additionally):
•
KVM CPU cable set (1.8m) with one side: PS/2 (6-pin mini-DIN male) keyboard and
mouse connector and DVI-I video (DVI-I dual link male) connector – other side: DVI-I
video (DVI-I dual link male) connector
•
PS2-Keyboard-/ Mouse adapter to connect K/M to the Local Unit (keyboard can be
plugged in directly, without using an adapter)
ACS4001A-xx and ACS4201A-xx (additionally):
•
DVI-I (1,8m) video cable (DVI-I dual link male-to-male)
•
USB (1,8m) cable (USB type A to type B)
ACS2209A-xx and ACS4201A-xx (additionally):
•
DVI-I (1,8m) video cable (DVI-I dual link male-to-male)
If anything is missing, please contact Technical Support (see Appendix F – Calling
Technical Support).
15
DVI-D FIBRE KVM-EXTENDER
3.2 Interconnection Cable Requirements
To connect the Local and Remote units you will need:
•
DVI, PS2-Keyboard, PS2-Mouse: Connect the supplied KVM CPU cable set to your
CPU (KVM.- Switch, etc.). Please ensure that the connection is tension-free! Devices
ACS1009A + ACS2209A
•
DVI, USB-Keyboard, USB-Mouse: Connect the supplied KVM CPU cable set to your
CPU (KVM.- Switch, etc.). Please ensure that the connection is tension-free! Devices
ACS4001A + ACS4201A
•
DVI: Connect the supplied DVI CPU cable set to your CPU (KVM.- Switch, etc.).
Please ensure that the connection is tension-free! Devices ACS2209A + ACS4201A
•
Fibre Cable: Two strands of fibre are required for singlehead devices, four strands for
Dualhead devices.
Please note, that the allowed distance will depend on device type AND on
used fibre type.
•
Recommended cables:
ACSxxxxA-MM: Multimode type 50/125µ
ACSxxxxA-MM: Multimode type 62.5/125µ
ACSxxxxA-SM: Singlemode type 9/125µ
allowed distance app. 400m (1,300ft)
allowed distance app. 200m (650ft)
allowed distance app. 10km (32,750ft)
A point to point connection is required. Having one or more patch panels
in the line is possible and allowed. Not allowed is a connection from the
Fibre link interface (LC) to any other products, especially
telecommunications or network equipment.
Our experiences show, that Singlemode devices regularily work well on
Multimode Fibres where vice versa it will never do. In addition we found,
that Singlemode devices on Multimode fibres may extend the allowed
distance on Multimode fibres to twice the regular length. Anyway this
cannot be guranteed and must be evaluated by the enduser at his own
expense.
•
Power Supply
Connect the supplied 5V/DC power supplies to the Plug terminal on the rear of both
Local and Remote units.
16
INSTALLATION
3.3 System Setup
To install your DVI-D Fibre – Extender system:
1.
Switch off all devices.
2.
Connect your keyboard, monitor(s) and mouse to the Remote unit (depending on device
type). Please ensure, to not swap Mouse- and Keyboard connector. The Keyboard
connector is purple and the Mouse connector is green.
3.
Using the supplied CPU KVM cable(s), connect the keyboard, monitor(s) and mouse
connectors on the computer (or KVM switch). Please ensure, to not swap Mouse- and
Keyboard connector. The Keyboard connector is purple and the Mouse connector is
green.
4.
Connect the interconnect cable to the INTERCONNECT socket(s)
5.
Connect the 5V power supply to power the unit.
Only use the power supply originally supplied with this
equipment or a manufacturer-approved replacement.
6.
For a dual access system, connect the monitor for the Local console to the appropriate
port on the Local unit. The port may also be used to feed into a KVM switch.
To the local (PS2-) Keyboard-/ Mouse port you can attach a Keyboard directly or
Mouse/ Keyboard together, using the delivered adapter.
To attach a local (USB-) Keyboard/Mouse, please use additional USB port(s) at your
CPU or use a USB Hub inbetween CPU and local unit’s USB connector.
7.
Power up the system.
17
DVI-D FIBRE KVM-EXTENDER
Connect to CPU:
DVI, keyboard, mouse
local DVI-Monitor port
Connect to Local
console monitor
Local keyboard/ mouse port
Solely Keyboard may be
plugged in directly,
keyboard/mouse through
equipped adapter
DVI-D Fibre KVM-Extender Type ACS1009A-xx Local Unit
remote DVI-Monitor
port– connect to
Remote console
monitor
Remote mouse port
Remote keyboard port
DVI-D Fibre KVM-Extender Type ACS1009A-xx Remote Unit
Connect to 5V Power
supply
INTERCONNECT – carries video and
data signals – connect to Local/
remote unit with Fibre cable
DVI-D Fibre KVM-Extender Type ACS1009A-xx Local/ Remote Unit
18
INSTALLATION
Connect to CPU:
2nd DVI-Graphic card
Connect to CPU:
1st DVI-Graphic card,
keyboard, mouse
2nd local DVI-Monitor
port Connect to Local
console 2nd monitor
local DVI-Monitor port
Connect to Local
console monitor
Local keyboard/ mouse port
Solely Keyboard may be
plugged in directly,
keyboard/mouse through
equipped adapter
DVI-D Fibre KVM-Extender Type ACS2209A-xx Local Unit
2nd remote DVI-Monitor
port Connect to Remote
console 2nd monitor
1st remote DVIMonitor port– connect
to Remote console 1st
monitor
Remote mouse port
Remote keyboard port
DVI-D Fibre KVM-Extender Type ACS2209A-xx Remote Unit
19
DVI-D FIBRE KVM-EXTENDER
INTERCONNECT – carries 2nd video –
connect to Local/Remote unit with
Fibre cable
Connect to 5V Power
supply
INTERCONNECT – carries 1st video
and data signals – connect to Local/
Remote unit with Fibre cable
DVI-D Fibre KVM-Extender Type ACS2209A-xx Local/ Remote Unit
20
INSTALLATION
Connect to CPU:
DVI graphic card
local DVI-Monitor port
Connect to Local
console monitor
Connect to CPU:
USB
DVI-D Fibre KVM-Extender Type ACS4001A-xx Local Unit
remote DVI-Monitor
port– connect to
Remote console
monitor
Remote keyboard/mouse
port
DVI-D Fibre KVM-Extender Type ACS4001A-xx Remote Unit
Connect to 5V Power
supply
INTERCONNECT – carries video and
data signals – connect to Local/
remote unit with Fibre cable
DVI-D Fibre KVM-Extender Type ACS4001A-xx Local/ Remote Unit
21
DVI-D FIBRE KVM-EXTENDER
Connect to CPU:
2 DVI-Graphic card
nd
Connect to CPU:
1 DVI-Graphic card
st
2nd local DVI-Monitor
port Connect to Local
console 2nd monitor
local 1st DVI-Monitor
port Connect to Local
console 1st monitor
Connect to CPU:
USB
DVI-D Fibre KVM-Extender Type ACS4201A-xx Local Unit
2nd remote DVI-Monitor
port Connect to Remote
console 2nd monitor
1st remote DVIMonitor port– connect
to Remote console 1st
monitor
Remote keyboard/ mouse
port
DVI-D Fibre KVM-Extender Type ACS4201A-xx Remote Unit
22
INSTALLATION
INTERCONNECT – carries 2nd video –
connect to Local/Remote unit with
Fibre cable
Connect to 5V Power
supply
INTERCONNECT – carries 1st video
and data signals – connect to Local/
Remote unit with Fibre cable
DVI-D Fibre KVM-Extender Type ACS4201A-xx Local/ Remote Unit
23
DVI-D FIBRE KVM-EXTENDER
3.4
Diagnostic LEDs
Each DVI-D Fibre KVM-Extender is fitted with four indicator LEDs: Power, Video OK, Data
Error, Link Status: The Power LEDs are next to the Power socket.
The location of the LEDs is shown below:
Diagnostic LED
Power
Diagnostic LED
Video OK
Diagnostic LED
Data Error
Diagnostic LED
Link Status
Diagnostic - LEDs at DVI-D Fibre - Extender
LED
Appearance
Diagnostics
Power LED
(Red LED)
Off
On
Device not ready
Device ready
Video Okay
(Green LED)
Off
On
No or invalid video signal detected
Device ready
Link Status
(Green LED)
blinking
On
No Fibre connection
Device ready
Data Error
(Green LED)
Off
blinking / On
Device ready
Errors through data transmission over Fibre Cable
(Cable too long, too high attenuation or too much
EMI interferences )
24
TROUBLESHOOTING
4.
Troubleshooting
There isn’t a picture.
Check the power supply connection at the Local unit. Is the Power (Red LED) at
the Local unit illuminated (see page 24)? If not, the internal power-supply may be
damaged or there may be an internal error.
Check the power supply connection at the remote unit. Is the Power (Red LED) at
the Remote unit illuminated (see page 24)? If not, the internal power-supply may be
damaged or there may be an internal error.
Check that the Interconnection cable is connected at the Local Unit and the Remote
Unit. Is the Link Status LED illuminated (see page 24)? If not, there may be a
problem with the Interconnection cable:
Are there Errors through data transmission over Fibre Cable (Cable too long, too
high attenuation or too much EMI interferences )? Is the Data Error LED
illuminated or blinking (see page 24)? If yes, check cable length and environment.
Video Okay LED is dark: CPU does not provide a video signal – Check settings of
the graphic card. Try out, connecting a monitor to the local output, to see, whether
ther is a signal or not.
PS2-Keyboard
The PC boots fine with no error messages but the keyboard does not work at all
Wrong cable plugged in, keyboard and mouse cables reversed.
Try a different model of keyboard. If the new keyboard works then original one
may be incompatible
Check that the Interconnection cable is connected at the Local Unit and the Remote
Unit. Is the Link Status LED illuminated (see page 24)?
PS2-Mouse
A mouse cursor appears on the screen, but the mouse does not work
Wrong cable plugged in, keyboard and mouse cables reversed.
Try a different model of mouse
You have connected the Local unit while the CPU was running. Therefore you have
connected first the keyboard cable and then the mouse cable. Disconnect the
keyboard cable and connect it again. Please reboot you CPU if the mouse is still not
running.
The system does not detect a PS/2 mouse, or the application cannot find the mouse.
Wrong cable plugged in, keyboard and mouse cables reversed.
Ensure that the Local Unit is connected to the PC keyboard port to provide power.
25
DVI-D FIBRE KVM-EXTENDER
USB-Keyboard/USB-Mouse
Your USB-keyboard/USB-mouse does not work
Although we tried to design the devices as transparent as possible, we can’t ensure
that all devices are running. Please check on page Fehler! Textmarke nicht
definiert. the list of the tested devices.
USB-HID device
Your USB-HID device does not work
Although our interface supports HID devices, we can’t ensure that every connected
device is running. In case of a malfunction please contact our technical support.
Other USB-devices
Your USB- device does not work
You have connected a non-HID device. There are supported HID devices only. All
other devices are dismissed
26
APPENDIX A: EXAMPLE APPLICATIONS
Appendix A: Example Applications
This section illustrates some specific applications using the DVI-D Fibre - Extenders:
•
DVI-D Fibre KVM-Extender with optional, secondary screen.
DVI-D Fibre KVM-Extender with optional, secondary screen
27
DVI-D FIBRE KVM-EXTENDER
•
4 CPU’s – local outputs managed through a KVM- Switch and a single console. Remote
Consoles up to 140m away.
DVI-D Fibre KVM-Extender – local Consoles through a KVM- Switch
28
APPENDIX B: RACK MOUNT OPTIONS
Appendix B: Rack Mount Options
DVI-D Fibre KVM- Extender units can be mounted in a 19” rack using the mounting kit:
DVI-D Fibre- Rackmount Kit. Two different versions are available – one each for
Singlehead and for Dualhead devices.
DVI-D Fibre- Rackmount Kit for Singlehead devices consists of:
Base plate
M2,5x5 Philips type
countersunk screws (8x)
M2,5x2 spacer (8x)
Drei Blindplatten
19” Rackmount Kit for Singlehead devices (ACS1009A-RMK)
DVI-D Fibre- Rackmount Kit for Singlehead devices consists of:
Base plate
M2,5x5 Philips type
countersunk screws (8x)
M2,5x2 spacer (8x)
Drei Blindplatten
19” Rackmount Kit for Dualhead devices (ACS2209A-RMK)
To mount a unit:
1.
Align the holes on the base plate with the vacant screw holes on the base of the DVI-D
Fibre KVM- Extender unit.
2.
Fasten the base of the unit to the plate of the mounting kit using the supplied screws.
Only use the supplied, short screws, to prevent damages on
the PCB’s
3.
Close the remaining gaps with blanking plates.
29
DVI-D FIBRE KVM-EXTENDER
The kit allows you to mount a different count of devices
(1…4 devices):
30
APPENDIX C: CALLING TECHNICAL SUPPORT
Appendix C: Calling Technical Support
If you determine that your DVI-D –Fibre KVM Extender is malfunctioning, do not attempt to
alter or repair it. It contains no user-serviceable parts. Contact Technical Support at Black
Box!
Before you do, make a record of the history of the problem. We will be able to provide more
efficient and accurate assistance if you have a complete description, including:
•
The firmware-revision level printed on the bottom of the Extender (very important,
especially for keyboard and mouse problems); The DVI-D FIBRE - KVM extender’s
firmware revision level:
Version Number Format:
Board:
xxLO/RE Myyy Pzzz Auuu Gvvvvvv
Transceiver:
C/M/S xx Pyy Mzz
Keyboard/Mouse:
P/U xx Vyyy
•
The nature and duration of the problem.
•
When the problem occurs.
•
The components involved in the problem—that is, what type of computers, what type of
keyboard, brand of mouse, make and model of monitor, type and make of cable, etc.
•
Any particular application that, when used, appears to create the problem or make it
worse.
•
The results of any testing you’ve already done.
To solve some problems, it might be necessary to upgrade the Extender’s firmware. If this
turns out to be the case for your difficulty, our Technical Support technicians will arrange for
you to receive the new firmware and will tell you how to install it.
Shipping and Packaging
If you need to transport or ship your DVI-D Fibre - KVM Extender:
•
Package it carefully. We recommend that you use the original container.
•
If you are shipping it for repair, please include the Unit’s external power supplies. If you
are returning it, please include everything you received with it. Before you ship the
Extender back to your dealer for repair or return, contact him to get a Return
Authorization (RA) number.
31
DVI-D FIBRE KVM-EXTENDER
Black Box Technical Support
Country
Web Site/E-Mail
US
www.blackbox.com
info@blackbox.com
724-746-5500
724-746-0746
Austria
www.black-box.at
support@black-box.at
+43 1 256 98 56
+43 1 256 98 56
Belgium
+32 2 725 85 50
www.blackbox.be
support.english@blackbox.be
support.french@blackbox.be
support.nederlands@blackbox.be
+32 2 725 92 12
Denmark
www.blackbox.dk
blackbox@blackbox.dk
+45 56 63 30 10
+45 56 65 08 05
Finland
www.blackbox.fi
tuki@blackbox.fi
+358 201 888 800
+358 201 888 808
France
www.blackbox.fr
tech@blackbox.fr
+33 820 07 09 11
+33 820 05 07 09
Germany
www.black-box.de
techsupp@black-box.de
+49 811 5541 110
+49 811 5541 499
Ireland
www.blackbox.co.uk
techhelp@blackbox.co.uk
+353 1 662 2466
+353 1 662 2477
Italy
www.blackbox.it
supporto.tecnico@blackbox.it
+39 02 27 404 700
+39 02 27 400 219
Netherlands www.blackbox.nl
techsupport@blackbox.nl
+31 30 241 7799
+31 30 241 4746
Norway
www.blackboxnorge.no
support@blackboxnorge.no
+47 55 300 710
+47 55 300 701
Spain
www.blackbox.es
tecnico@blackbox.es
+34 916590732
+34 916239784
Sweden
www.blackboxab.se
support@blackboxab.se
+46 8 44 55 890
+46 08 38 04 30
Switzerland
www.black-box.ch
support@black-box.ch
+41 55 451 70 71
+41 55 451 70 75
UK
www.blackbox.co.uk
techhelp@blackbox.co.uk
+44 118 965 6000
+44 118 965 6001
32
Phone
Fax
APPENDIX D: SPECIFICATIONS
Appendix D: Specifications
Power Supply
Voltage
100-240VAC-0.5A-47-63Hz/5VDC-2000 mA
Power required
Local Unit : max. 750mA
Remote Unit : max. 750mA
Interface
(Depending on type of device)
Video source/Monitor
DVI-D up to 1600x1200@60Hz
Keyboard
PS2 or USB (depending on model)
Mouse
PS2 or USB (depending on model) 2-/3-button and
wheel mouse
Maximum Length of Interconnection Cable
Singlemode 9 µm
10.000m (32.750ft)
Multimode 50µm
400m (1.300ft)
Multimode 62.5µm
200m (650ft)
33
DVI-D FIBRE KVM-EXTENDER
Size and Shipping Weight
DVI-D Fibre
103 x 143 x 29mm (4”x5.6”x1.1”) (2 devices)
Weight: 0,6kg (1.3lb) each
Shipping box
Weight: 1,6 kg (3.5lb)
Environmental
Operating Temperature
41 to 113°F (5 to 45 °C)
Storage Temperature
-13 to 140°F (-25 to 60 °C)
Relative Humidity
max. 80% non-condensing
34
APPENDIX E: CONNECTORS
Appendix E: Connectors
DVI-D Fibre KVM-Extender Connector Pinouts
DVI-I female connector (Output connector for ALL devices and Input connector
Dualhead devices 2nd Monitor)
1
8
C1
C2
C5
17
C4
Pin
Signal
24
Pin
Signal
C3
Pin
Signal
1
T.M.D.S data 2-
9
T.M.D.S data 1-
17
T.M.D.S data 0-
2
T.M.D.S data 2+
10
T.M.D.S data 1+
18
T.M.D.S data 0+
3
T.M.D.S data 2 GND
11
T.M.D.S data 1 GND
19
T.M.D.S data 0 GND
4
n.c.
12
n.c.
20
n.c.
5
n.c.
13
n.c.
21
n.c.
6
DDC Input (SCL)
14
+5V high impedance
22
T.M.D.S clock GND
7
DDC Output(SDA)
15
GND
23
T.M.D.S clock +
8
Internal use.
16
Hot Plug recognition
24
T.M.D.S clock -
C1
Internal use.
C3
Internal use.
C2
n.c.
C4
Internal use.
C5
GND
35
DVI-D FIBRE KVM-EXTENDER
DVI-I female connector (Input connector for ALL Singlehead devices and Input
connector Dualhead devices 1st Monitor)
C5
17
C4
Pin
Signal
24
Pin
Signal
C3
Pin
Signal
1
T.M.D.S data 2-
9
T.M.D.S data 1-
17
T.M.D.S data 0-
2
T.M.D.S data 2+
10
T.M.D.S data 1+
18
T.M.D.S data 0+
3
T.M.D.S data 2 GND
11
T.M.D.S data 1 GND
19
T.M.D.S data 0 GND
4
PS2-KBD CLK
12
PS2-MOUSE CLK
20
PS2-MOUSE VCC-IN +5V
(not required)
5
PS2-KBD DATA
13
PS”-MOUSE-DATA
21
PS2-KBD VCC-IN +5V
(always required)
6
DDC Input (SCL)
14
+5V In for DDC
22
T.M.D.S clock GND
7
DDC Output(SDA)
15
GND
23
T.M.D.S clock +
8
Analog VSYNC
16
Hot Plug recognition
24
T.M.D.S clock -
C3
n.c.
C4
n.c.
C1
n.c.
C2
n.c.
36
C5
GND
APPENDIX E: CONNECTORS
Combined Keyboard/Mouse connector (output connector Local Unit)
Pin
1
KBD-DATA
2
MOUSE-DATA
3
KBD/MOUSE-GND
4
VCC (+5V)
5
KBD-CLK
6
MOUSE-CLK
Keyboard/Mouse connector (output connector Remote Unit)
Pin
1
Keyboard
KBD-DATA
2
KBD-GND
4
6
1
Mouse
MOUSE-DATA
2
3
5
Pin
3
MOUSE-GND
VCC (+5V)
4
VCC (+5V)
KBD-CLK
5
MOUSE-CLK
6
37
DVI-D FIBRE KVM-EXTENDER
Keyboard/Mouse Adapter to connect Keyboard/Mouse to Local Unit
Pin
Connector (device)
Pin
Keyboard
1
KBD-DATA
1
KBD-DATA
2
MOUSE-DATA
2
3
KBD-GND
3
KBD -GND
4
VCC (+5V)
4
5
KBD-CLK
5
6
MOUSE-CLK
6
Mouse
2
1
MOUSE-DATA
3
MOUSE-GND
VCC (+5V)
4
VCC (+5V)
KBD -CLK
6
5
Power
38
Pin
Pin
Signal
inner
+5V
outer
GND
MOUSE-CLK
NOTES
Download PDF

advertising