Specifications | Black Box 5-/8-Port 10/100/Gigabit Switch with 1 PoE PD Port Computer Accessories User Manual

5-/8-Port 10/100/Gigabit Switch with 1 PoE PD Port
Expand the number of Gigabit Ethernet ports
on your network without the need for a power
Includes a built-in IEEE 802.3af Power Device (PD).
Unit is palm-sized with metal case.
Auto-negotiates port speed.
Includes auto-MDI/MDI-X function for every port.
5-/8-Port 10-/100-/Gigabit Switch with 1 PoE PD port
Federal Communications Commission and Industry Canada
Radio Frequency Interference Statements
This equipment generates, uses, and can radiate radio-frequency energy, and if not installed and used properly, that is, in
strict accordance with the manufacturer’s instructions, may cause inter-ference to radio communication. It has been tested
and found to comply with the limits for a Class A computing device in accordance with the specifications in Subpart B of
Part 15 of FCC rules, which are designed to provide reasonable protection against such interference when the equipment
is operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference,
in which case the user at his own expense will be required to take whatever measures may be necessary to correct the
interference. Changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
This digital apparatus does not exceed the Class A limits for radio noise emis-sion from digital apparatus set out in the
Radio Interference Regulation of Industry Canada.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils
numériques de la classe A prescrites dans le Règlement sur le brouillage radioélectrique publié par Industrie Canada.
CE Warning
This is a Class A product. In a domestic environment, this product may cause radio interference in which case the user
may be required to take adequate measures to correct the interference.
Normas Oficiales Mexicanas (NOM) Electrical Safety Statement
Todas las instrucciones de seguridad y operación deberán ser leídas antes de que el aparato eléctrico sea operado.
Las instrucciones de seguridad y operación deberán ser guardadas para referencia futura.
Todas las advertencias en el aparato eléctrico y en sus instrucciones de operación deben ser respetadas.
Todas las instrucciones de operación y uso deben ser seguidas.
El aparato eléctrico no deberá ser usado cerca del agua—por ejemplo, cerca de la tina de baño, lavabo, sótano
mojado o cerca de una alberca, etc..
6. El aparato eléctrico debe ser usado únicamente con carritos o pedestales que sean recomendados por el fabricante.
7. El aparato eléctrico debe ser montado a la pared o al techo sólo como sea recomendado por el fabricante.
8. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico más allá a lo descrito en las instrucciones de
operación. Todo otro servicio deberá ser referido a personal de servicio calificado.
9. El aparato eléctrico debe ser situado de tal manera que su posición no interfiera su uso. La colocación del aparato
eléctrico sobre una cama, sofá, alfombra o superficie similar puede bloquea la ventilación, no se debe colocar en
libreros o gabinetes que impidan el flujo de aire por los orificios de ventilación.
10. El equipo eléctrico deber ser situado fuera del alcance de fuentes de calor como radiadores, registros de calor,
estufas u otros aparatos (incluyendo amplificadores) que producen calor.
11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo del tipo descrito en el instructivo de operación,
o como se indique en el aparato.
12. Precaución debe ser tomada de tal manera que la tierra fisica y la polarización del equipo no sea eliminada.
13. Los cables de la fuente de poder deben ser guiados de tal manera que no sean pisados ni pellizcados por objetos
colocados sobre o contra ellos, poniendo particular atención a los contactos y receptáculos donde salen del aparato.
14. El equipo eléctrico debe ser limpiado únicamente de acuerdo a las recomendaciones del fabricante.
15. En caso de existir, una antena externa deberá ser localizada lejos de las lineas de energia.
16. El cable de corriente deberá ser desconectado del cuando el equipo no sea usado por un largo periodo de tiempo.
17. Cuidado debe ser tomado de tal manera que objectos liquidos no sean derramados sobre la cubierta u orificios de
18. Servicio por personal calificado deberá ser provisto cuando:
A: El cable de poder o el contacto ha sido dañado; u
B: Objectos han caído o líquido ha sido derramado dentro del aparato; o
C: El aparato ha sido expuesto a la lluvia; o
D: El aparato parece no operar normalmente o muestra un cambio en su desempeño; o
E: El aparato ha sido tirado o su cubierta ha sido dañada.
Page 2
724-746-5500 l www.blackbox.com
Chapter 1: Introduction
Trademarks Used in this Manual
Black Box and the Double Diamond logo are registered trademarks of BB Technologies, Inc.
Any other trademarks mentioned in this manual are acknowledged to be the property of the trademark owners.
1. Introduction
These switches provide (5) or (8) 10-/100-/1000-Mbps ports. They were designed for easy installation and high
performance in environments where traffic on the network and the number of users increases continuously.
Both switches have a built in Power Device (PD) feature on port 1. Using this port, you can power the switch from a PSE
port over ordinary CAT5 cables.
The small compact unit was specifically designed for small to medium workgroups. Install it where space is limited for
smooth network migration and an easy upgrade to network capacity.
2. Key Features
5-/8-Port 10/100/1000 Mbps (Auto-negotiation) Switch
Ports 5/8 have a built in IEEE 802.3af Power Device (PD) feature that allows the switch to get power from a PSE
device over ordinary CAT5 cables.
Unit is palm-sized with metal case
Auto-detects full-/half-duplex modes for any port
Offers dedicated full-duplex 2000-Mbps bandwidth
Supports Store-and-Forward switching methods
Includes IEEE 802.3x flow control for full-duplex and back-pressure flow control for half-duplex
Provides non-blocking and non-head-of-line blocking full wire speed forwarding
Supports Auto-MDI/MDI-X function for any port
3. Package Contents
Your package should include the following items. If anything is missing or damaged, please contact Black Box Technical
Support at 724-746-5500 or info@blackbox.com.
(1) Gigabit Ethernet Switch
(1) Power Adapter: 120 VAC, 60 Hz U.S. plug for LPDG705A and LPDG708A; 100-240 VAC, 50–60 Hz, 0.4 A
universal power supply with (2) power clips: (1) EU, (1) UK for LPDG705AE and LPDG708AE
(1) User’s Manual
724-746-5500 l www.blackbox.com
Page 3
5-/8-Port 10-/100-/Gigabit Switch with 1 PoE PD port
4. Front & Rear Panel
Front Panel
Figure 4-1. Front panel of the LPDG708A.
NOTE: The front panel of the LPDG705A is similar to the LPDG708A, except that is has six LEDs (1 power, 5 Link/Act)
instead of eight LEDs. LED 5 on LPDG705A and LED 8 on the LPDG708A indicate the Link/Act status of the PoE port.
LED Indicators on the switch
Power is on.
Power is off.
Port is for connection.
No connection.
Data is transmitting or receiving
Rear Panel (Connections)
Port 5 on the LPDG705A also functions as a PoE port.
Port 8 on the LPDG708A also functions as a PoE port.
Figure 4-2. Back panels of the LPDG705A and LPDG708A.
Page 4
724-746-5500 l www.blackbox.com
Chapter 5: Connection
5. Connection
TP Port and Cable Installation:
1. The switch’s TP ports support MDI-/MDI-X auto-crossover, so you can use either straight through or cross over cables.
2. Use CAT5 or higher grade RJ-45 TP cable for 10/100 applications and CAT5e grade RJ-45 TP cable or above for
gigabit Ethernet applications, to connect a TP port of the switch to an Ethernet device such as a workstation or a server.
3. Repeat the above steps, as needed, for each RJ-45 port to be connected to a 10-/100-/1000-Mbps TP device.
For successful installation and good performance, follow the cabling requirements. Using cables with a lower
specification than recommended will negatively impact network performance. For Fast Ethernet TP network connection,
you must use CAT5 or higher cables that are up to 328 feet (100 meters) long. For Gigabit TP network connections, you
must use CAT5e or higher cables that are up to 328 feet (100 meters) long.
Power On:
Power this switch from PoE PSE (Power Source Equipment) or from external DC power adapter. When connecting a PoE
PSE, make sure that your PSE complies with 802.3af or 48 VDC 15.4 W.
After the power is on, all LED indicators will light immediately. Then all LEDs will turn off, except for the power LED, which
stays on.
724-746-5500 l www.blackbox.com
Page 5
5-/8-Port 10-/100-/Gigabit Switch with 1 PoE PD port
6. Technical Specifications
Forwarding Rates
Transmission Media
LED Indicators
Power Supply
Power Consumption
Operating Temperature
Storage Temperature
Page 6
IEEE 802.3af
IEEE 802.3 10BaseT
IEEE 802.3u 100BaseTX
IEEE 802.3ab 1000BaseT
IEEE 802.3x Flow control
Number of Ports: LPDG705A: (5) 10-/100-/1000BASE-T(X) with 1 PD
(PoE) Port
LPDG708A: (8) 10-/100-/1000BASE-T(X) with 1 PD (PoE) Port
MAC Address: 2K
Buffer Memory: 1M bits
Method: Store and Forward
1000-Mbps port : 1,488,000 pps
100-Mbps port : 148,800pps
10-Mbps: 14,880pps
100BASE-TX CAT5, 5e, 6 UTP/STP
Per Port: LINK/ACT
Per Unit: Power
LPDG705A, LPDG708A: Input: 120 VAC, 60 Hz with U.S. plug,
Output: 5 VDC, 2 A, 10 W max.;
LPDG705AE, LPDG708AE: Input: 100-240 VAC, 50–60 Hz, 0.4 A,
universal power supply with (2) power clips: (1) EU, (1) UK,
Output: 5 VDC, 2 A, 10 W max.
6 Watts (Maximum)
0.9”H x 3”W x 5.2”D (2.4 x 7.7 x 13 cm)
0.28 kg
32 to 104° F(0 to 40° C)
-4 to 194° F (-20 to 90 C)
10 to 90% relative humidity (non-condensing)
FCC Class A, CE
724-746-5500 l www.blackbox.com
LPDG705A, rev. 3
Download PDF