Blaupunkt 2000 DJ Car Stereo System User Manual

Radio / Cassette
Chicago RCM 169
Hannover 2000 DJ
Kansas DJ
Montreal RCM 169
Paris RCM 169
Operating instructions
2
1
13
3
12
4
5
9
10
11
8
7
6
19
18
15
1
3
2
17
16
Chicago RCM 169
Option / Optional /
Tilval / Optie /
Opcional / Opção:
2
14
21
20 Hannover 2000 DJ
Kansas DJ
Montreal RCM 169
Paris RCM 169
Table of contents
Quick Reference ........................... 45
RC 08 remote control unit ........... 53
Important notes ............................ 54
What you need to know ........................ 54
Traffic safety ......................................... 54
Installation ............................................. 54
Telephone mute .................................... 54
Accessories .......................................... 54
Guarantee ............................................. 54
International telephone information ...... 54
KeyCard theft protection system 55
Putting the unit into operation .............. 55
Removing the KeyCard ........................ 55
“Training” a second KeyCard/
Replacing a KeyCard ............................ 55
Displaying the radio pass data ............. 56
Short Additional Memory (S.A.M.) ........ 56
Turn On Message (T.O.M.) .................. 56
Optical display as theft protection ........ 56
Care of your KeyCard ........................... 57
Lost or damaged KeyCard ................... 57
Training the new KeyCard .................... 57
Selecting the operating mode ..... 58
Optimising display legibility ....... 58
Radio operation with RDS ........... 59
AF - Alternative frequency .................... 59
REG - regional program ....................... 59
Selecting a waveband .......................... 60
Station tuning ........................................ 60
Storing stations ..................................... 61
Selecting the seek tuning sensitivity .... 62
Switching from stereo to mono (FM) .... 63
Automatic bandwidth adjustment
(SHARX) ............................................... 63
PTY - Program Type ............................. 63
Program type ........................................ 63
Traffic information station
reception with RDS-EON ............. 66
Traffic announcement priority on/off .... 66
Warning beep ....................................... 66
Switching the warning beep off ............ 66
Automatic search function .................... 66
Adjusting the volume for traffic
announcements and the warning beep .. 66
Cassette operation ....................... 67
Dolby B NR* .......................................... 67
Selecting the display mode .................. 67
Track reverse ........................................ 68
Scanning cassette titles with SCAN ..... 68
Selecting titles with S-CPS ................... 68
Repeating titles with RPT ..................... 69
Fast tape forward/rewind ...................... 69
Listening to the radio while fast forwarding
or rewinding the tape with Radio Monitor 69
Automatically skipping over blank portions
of the tape with Blank Skip (BLS) ........... 69
Care instructions ................................... 69
Changer operation ....................... 70
Switching on CD changer operation ..... 70
Selecting the display mode .................. 70
Selecting CDs and tracks ..................... 70
Repeat tracks/CDs with RPT ................ 71
TPM (Track Program Memory) ............. 71
MIX ........................................................ 72
SCAN .................................................... 72
Entering CD names .............................. 72
Deleting CD names/TPM with DSC
UPDATE ............................................... 73
Clock - Time .................................. 74
Correcting the clock after the power
has been disconnected ......................... 74
Deactivating the hour correction
function ................................................. 74
Setting the equaliser .................... 75
Notes on making the settings ............... 75
Setting recommendations on the
Internet .................................................. 75
Assistance in setting your equaliser ..... 76
DSC programming ....................... 77
Overview of the DSC factory settings .. 80
Specifications ............................... 80
Glossary Technical Terminology ................ 81
Index .............................................. 83
Installation and
connection instructions ............ 333
44
ChicHanKanMonParis gb 95%®
44
14.05.2002, 14:24 Uhr
2
1
3
Switching the sound on/off:
Press ON briefly. When the sound has
been switched off, “MUTE” will appear
in the display.
The sound can be switched on again
by turning the volume knob 3.
Switching the unit on with the ignition switched off:
After you have switched off the ignition
(KeyCard is inserted in the unit), you
can continue to operate the unit as follows:
After the double beep press ON.
The unit will switch on.
After the unit has played for an hour it
will switch off automatically to prevent
the car battery from running down.
DEUTSCH
ENGLISH
FRANÇAIS
PORTUGUÊS
For safety’s sake, the operating
panel must remain locked when
the vehicle is in motion.
When you leave the vehicle, unlock the panel and remove the
KeyCard to protect the equipment
against theft.
The viewing angle of the display can
be adjusted individually to ensure optimum legibility. If necessary, refer to
the section on “Optimising the display
legibility”.
Switching the unit on/off with the
ignition:
If the unit has been connected accordingly, it can be switched on and off
with the car ignition.
After you switch off the ignition, a double beep will sound to remind you to
remove the KeyCard and take it with
you.
ITALIANO
To switch off the unit:
Press ON for approx. 1 second.
Switching the unit on/off with the
KeyCard:
The unit switches on or off when the
KeyCard is inserted or removed.
Refer to section @ in the Quick Reference on the KeyCard theft protection
system.
NEDERLANDS
2 ON
Switching the unit on:
With the KeyCard inserted, press ON
briefly.
The unit will begin to play in the operating mode selected last at the pre-set
volume.
SVENSKA
1 Unlocking the fold-down operating
panel
It is possible to insert or remove the
KeyCard and the cassette when the
operating panel is unlocked.
To unlock the panel press 1, the operating panel will fold down. The operating panel cannot be removed. Do not
use the panel as a rest or shelf.
To lock the panel, push it back into its
starting position (arrow 3).
ESPAÑOL
Quick Reference
45
ChicHanKanMonParis gb 95%®
45
14.05.2002, 14:24 Uhr
Quick Reference
3 Adjusting the volume
Turn the knob to adjust the volume as
desired.
The volume level selected will appear
in the display. When the unit is
switched on, it will automatically play
at the pre-set volume (ON VOL).
It is possible to adjust the ON VOL (refer to “DSC programming - ON VOL”).
4 Softkeys / Display
Softkey = key with different functions
The functions which appear in the display can be selected.
Radio operation
While listening to the radio you can
press TU to switch between menu level 1 and menu level 2.
The unit will return to menu level 1 automatically 8 seconds after the last key
is pressed.
Menu level 1
Station keys and memory levels
Menu level 2
Adjusting the radio functions
NEXT - FM
Switches between the memory levels
for FM I, FM II, FM T.
NEXT - AM (MW, LW)
Switches between the MW and LW
wavebands.
NEXT - FM
Switches between the memory levels
for FM I, FM II, FM T.
NEXT - AM (MW, LW)
Switches between the MW and LW
wavebands.
ST1 - ST6
On this memory level it is possible to
store radio stations on the FM levels I, II
and “T” on the keys marked ST1 to ST6.
6 stations each can be stored for the
MW and LW wavebands.
Storing a radio station - Press one of
the station keys from ST1 to ST6 until
it is possible to hear the program again
(beep).
Recalling a radio station - Select the
desired waveband. For FM press
NEXT to select the memory level required and press the corresponding
station key briefly.
BND
Selects the waveband and memory
level (FM I, FM II, FM T, MW, LW).
SCA - Scan
a) PTY is switched off
(lettering is lit normally, not highlighted
in the display)
Press SCA briefly (Radio Scan) “SCAN” will flash in the display alternately with the abbreviation for the station being scanned. All of the radio
stations within reception range will be
scanned.
46
ChicHanKanMonParis gb 95%®
46
14.05.2002, 14:24 Uhr
PTY
(Program Type)
With PTY the station keys become program type keys.
“PTY” must be highlighted in the display (press PTY if necessary).
Now it is possible to select a program
type such as NEWS, SPORT, POP,
and store it on one of the station keys.
AF (Alternative Frequency for RDS
operation)
If “AF” is highlighted in the display, the
radio will automatically search for a
In the cassette mode, the softkeys can
be used to select the corresponding
cassette functions.
REVerse
Switches to the opposite track (side).
The display indicates which track is
currently playing (Side A/B).
47
ChicHanKanMonParis gb 95%®
47
DEUTSCH
Press SCA the stations broadcasting the programs for the PTY program type selected will be scanned.
Cassette operation
ENGLISH
TS (Travelstore)
If you press TS, the radio will switch to
FMT from any other waveband. The
six stations with the strongest reception will be stored automatically. After
the stations have been stored, the radio will tune into the station with the
best reception and begin to play.
FRANÇAIS
b) PTY is switched on
(lettering is highlighted in the display)
NEDERLANDS
ENT (Enter)
Press this key briefly to accept or store
an adjustment.
REG (Regional function)
This function is active when “REG” is
highlighted in the display.
REG on/off: Press TU to select menu
level 2 and press REG briefly.
If necessary, refer to the section on
REG - Regional in the more detailed
instructions.
SVENSKA
Stopping Radio Scan / Preset Scan:
Press SCA or the rocker switch once
again.
EXIT
Press this key briefly to end or cancel
an adjustment.
Press << >> to activate the PTY program types and press the station keys
to store them (press the key for approx. 2 seconds, until you hear a
beep).
14.05.2002, 14:24 Uhr
ESPAÑOL
frequency with better reception for the
station you are tuned into.
AF on/off: Press TU to select menu
level 2 and press AF briefly.
PORTUGUÊS
Press SCA for approx. 1 second
(Preset Scan) You will hear a beep and “SCAN” will
flash in the display alternately with the
abbreviation for the station being
scanned. The radio stations which
have been stored on the station keys
and which are currently within reception range will be scanned.
ITALIANO
Quick Reference
Quick Reference
SCA (Scan)
Briefly scans the cassette titles.
Starting/ending Scan: Press SCA.
When the function is active, “SCAN”
will appear in the display.
RPT (Repeat)
To repeat the scanned or the next title.
The title will repeat until RPT is
switched off.
The Repeat function will end automatically when the cassette is removed or
the set is switched off.
Switching Repeat on/off: Press RPT,
the activated function will appear briefly in the display to indicate whether it is
switched on or off.
Dolby B NR*
Cassettes recorded using Dolby B NR
will playback in the best quality when
symbol appears on a highlighted
the
background.
* The noise reduction system is manufactured
under licence by the Dolby Laboratories Licensing Corporation. The word DOLBY and the double-D symbol are trademarks of the DOLBY Laboratories.
RM (Radio Monitor)
To listen to the radio while fast forwarding or rewinding the tape. When
“RM” appears highlighted in the display, it is possible to listen to the radio
while the tape is rewinding or forwarding.
Switching Radio Monitor on/off: Press
RM, the activated function will appear
briefly in the display to indicate whether it is switched on or off.
Changer operation
BLS (Blank Skip)
The set skips over blank portions of
the tape when “BLS” appears highlighted in the display. As soon as there is a
break of more than 10 sec. during cassette playback, the fast forward function will be activated to move to the
next title.
Switching Blank Skip on/off: Press
BLS, the activated function will appear
briefly in the display to indicate whether it is switched on or off.
MIX
CD tracks will be played in random order.
Press the MIX key to select the following functions:
- MIX CD = the tracks on the CD will
be played in random order.
If you are using a CD changer, the
CDs will be selected in numerical order and the tracks in random order.
- MIX MAG = all of the tracks on all of
the CDs in the magazine will be
played in random order.
- MIX OFF = switches the function off.
In the changer mode, the softkeys can
be used to select the corresponding
changer functions.
SCA - Scan
Scans all of the tracks on a CD.
48
ChicHanKanMonParis gb 95%®
48
14.05.2002, 14:24 Uhr
CLR
To clear the TPM memory. (See the
section on “TPM - Deleting the memory”)
Radio operation
If you press the rocker switch when the
unit is on menu level 2, it will automatically return to menu level 1.
ENGLISH
FRANÇAIS
6 Rocker switch
>>
<<
ITALIANO
/
Select title (S-CPS)
forwards
back
NEDERLANDS
TPM - Track Program Memory
Stores and plays your favourite tracks.
It is possible to manage up to 99 CDs
with up to 40 tracks. (Refer to the section on “TPM programming”.)
Cassette operation
fast forward
fast rewind
Changer operation
SVENSKA
RPT - Repeat
CD tracks or CDs in the CD changer
can be repeated as often as desired.
Press the RPT key to select one of the
following functions:
- REP TRCK = Repeat track
- REP CD = Repeat CD
- RPT OFF = switches the function off
For FM only:
<< / >> Pages through the station chain
with AF on and PTY off
e.g.: NDR 1, 2, 3, 4, N-JOY, ...
/
Station seek tuning
up
down
<< / >> down/up in short intervals
(for FM only when AF and PTY are
switched off)
ESPAÑOL
Stop Scan:
Press SCA. The track scanned last will
begin to play.
5 TA (Traffic Announcement = priority
for traffic information)
“TP” will appear in the display when
the radio is tuned into a traffic information station.
“TA” will appear in the display when
the priority for traffic information has
been activated.
The radio will then play traffic information radio stations only.
Priority on/off: Press TA.
Interrupt an announcement: Press TA
or EXIT.
<< / >> Select CD
>>
up: Press briefly
<<
down: Press briefly
PORTUGUÊS
Start Scan:
Press SCA. The tracks will be scanned
in ascending order one after the other.
The scan time can be adjusted (see
“DSC programming - SCANTIME”).
DEUTSCH
Quick Reference
49
ChicHanKanMonParis gb 95%®
49
14.05.2002, 14:24 Uhr
Quick Reference
/
Select track
up: Press briefly
CUE - fast forward (audible):
Hold pressed down
down: Press twice or repeatedly
briefly
To restart the track: Press briefly
REVIEW - fast reverse (audible):
Hold pressed down
Additional functions for the rocker
switch:
Other adjustments are possible with
AUD
8
DSC-MODE 7
PTY
as long as the corresponding function
is activated.
8 AUD
Adjusts treble, bass, balance (left/
right), fader (front/rear) and Loudness.
Loudness = Boosts low frequency for
more bass and a better adjustment to
the human ear.
Kansas DJ, Chicago RCM 169:
For FM, AM, CD, AUX and TA it is
possible to store different treble, bass
and loudness settings.
How to make the settings:
Select the operating mode.
Press AUD once, “BASS” and the level
currently selected will appear in the
display.
7 DSC (Direct Software Control)
Using DSC it is possible to adjust the
programmable basic settings.
Further information: “DSC programming”.
Special Loudness feature:
Press / to select the setting from
LOUD 6 to LOUD OFF.
Switching off AUD:
Press EXIT.
If you do not alter any of the settings,
AUD will switch off automatically after
8 seconds.
Additional feature
Switching the equaliser on/off (DPE
ON/OFF):
Press AUD for approx. 2 seconds.
“DPE ON” or “DPE OFF” will appear
briefly in the display.
For more information on the equaliser:
Refer to “Setting the equaliser”.
9 DIS
Selects different display modes.
Radio operation
Use << / >> to select the different
modes.
Use / to make the corresponding
settings.
The settings selected will appear in the
display. The setting selected last will
be stored automatically.
Press DIS briefly:
- Name of the current radio station
- Current frequency
- PTY code
This will not work properly unless the
radio is able to receive an RDS station
in adequate reception quality.
50
ChicHanKanMonParis gb 95%®
50
14.05.2002, 14:24 Uhr
RM
Press DIS briefly:
The display mode selected will appear
briefly in the display.
PTY
AF
“COUNTER” - tape counter
“CLOCK”
- time
“ELAPSED” - elapsed playing time for
the tape side
“REMAIN” - remaining playing time
on the tape side
EQ
CC-IN
SIDE A
REV
- Side (track) A is playing
- Reverse (tape side reverse)
lo
Changer operation
Press DIS briefly:
- CD number, track number, clock
- CD number, track number, time
played
- CD name, track number
ITALIANO
TP, TA
CD 10 T3 - CD number and track number
or
VIVALDI - CD name
MIX
- CD tracks can be played in
random order
SCA
- CD tracks are being scanned
RPT
- Repeat function for changer
operation
TPM
- Store and play favourite CD
tracks
CLR
- Delete TPM memory
51
ChicHanKanMonParis gb 95%®
51
14.05.2002, 14:24 Uhr
NEDERLANDS
Cassette operation
- station name
- waveband
- memory level I, II or Travelstore
- TP = Traffic Program
- TA = Priority for traffic information is activated
- Program type is activated
- Alternative frequency for
RDS
- Seek tuning sensitivity adjustable with DSC
- Equaliser is switched on
- Cassette is inserted
SVENSKA
NDR2
FM
I, II, T
ESPAÑOL
Press DIS for approx. 2 seconds:
Display will alternate between the
clock and the waveband (incl. the
memory level for FM).
FRANÇAIS
BLS
- Scans cassette titles briefly
- Title repeat function for cassette operation
- Dolby B NR is active
- Radio listening during fast
tape forwarding or rewind
- Blank tape portions will be
skipped automatically
DEUTSCH
SCA
RPT
PORTUGUÊS
: Display
ENGLISH
Quick Reference
Quick Reference
FM I, II, T
or
MW, LW
or
00:20
or
12:50
- FM memory level
- Waveband
- Time played
- Clock
; CDC
Switches to changer operation (only if
a changer is connected).
If there is no changer, the system will
switch to AUX as long as AUX ON is
switched on in the DSC menu.
< CC
Switches to cassette operation
= TU (TUNER)
Switches to radio operation. Switches
to the memory levels/wavebands FM I,
FM II, TS (Travelstore), MW and LW.
? Visual theft protection
The following conditions must be fulfilled before the light diode will flash as
a visual indication of theft protection:
The unit is switched off;
The operating panel is folded down;
The KeyCard has been removed;
The DSC menu settings is switched to
LED ON (factory setting).
For more information, refer to “DSC
programming, LED ON/OFF”.
Perform these steps in the reverse order to remove the KeyCard.
Make sure to read the information in
the section on “KeyCard theft protection system”.
A Eject
Press the Eject button briefly to eject
the cassette.
@ KeyCard theft protection system
The KeyCard must be inserted before
the unit can be operated.
KeyCard
Inserting the KeyCard
Press 1 to unlock the operating panel; it will fold down forwards.
Insert the KeyCard with the contact
points facing down (see illustration).
Lock the operating panel.
2
> Cassette slot
Insert cassette (Side A or 1 facing up;
opening to the right).
For safety’s sake, the operating
panel must remain locked when
the vehicle is in motion.
When you leave the vehicle, unlock the panel and remove the
KeyCard to protect the equipment
against theft.
1
52
ChicHanKanMonParis gb 95%®
3
52
14.05.2002, 14:24 Uhr
18
<< / >> down/up in short intervals
(for FM only when AF and
PTY are switched off)
For FM only:
<< / >> Pages through the station
chain with AF on and PTY off
e.g.: NDR 1, 2, 3, 4, N-JOY, ...
20
Cassette operation
/
E
Sound mute on/off:
briefly. When the sound has
Press
been switched off “MUTE” will appear
in the display.
Select title (S-CPS)
forwards
back
Cassette operation
fast forward
fast rewind
Track switch:
Press
for approx. 1 sec.
B V- / V+
Volume control
>>
<<
C SRC (Source)
Switches operating modes
- Radio
- CC (Cassette)
- Changer (if a changer is connected)
Changer operation
Switching sound on/off:
briefly.
Press
<< / >> Select CD
>>
up: Press briefly
<<
down: Press briefly
53
ChicHanKanMonParis gb 95%®
53
DEUTSCH
ENGLISH
Station seek tuning
up
down
ESPAÑOL
21
Radio operation
Select track
up: Press briefly
CUE - fast forward (audible):
Hold pressed down
down: Press twice or repeatedly briefly
To restart the track: Press
briefly
REVIEW - fast reverse (audible): Hold pressed down
FRANÇAIS
19
/
ITALIANO
Hannover 2000 DJ
Kansas DJ
Montreal RCM 169
Paris RCM 169
/
PORTUGUÊS
Optional:
D << / >>,
SVENSKA
Included with package: Chicago RCM 169
NEDERLANDS
RC 08 remote control unit
14.05.2002, 14:24 Uhr
Important notes
What you need to know
Telephone mute
Before using your new car audio system,
please read through the following information carefully.
If a car phone has been installed, it is possible to mute radio, cassette and CD playback
automatically during a telephone call (telephone mute). “PHONE” will then appear in
the display.
Amplifiers
All Blaupunkt amplifiers
As the driver of a motor vehicle, it is your
responsibility to pay attention to the traffic
situation at all times. Never use your car audio system in a way that could distract you.
Traffic announcements continue to have
priority if you have activated TA. You can
interrupt traffic messages by pressing TA.
CD changers
The following CD changers can be connected directly: CDC A 06, A 072, A 08.
The A 05 and the A 071 can be connected
with the adapter cable 7 607 889 093.
The CDC-A 08 is included with the Hannover 2000 DJ / Kansas DJ.
Please keep in mind that you travel a distance of 14 m per second at a speed of only
50 km/h.
Accessories
Guarantee
Use only Blaupunkt-approved accessories
and spare parts.
You can use the following Blaupunkt products with this unit:
The scope of the guarantee is determined
by the laws in the country where the unit
was purchased.
Regardless of the legal guarantee regulations, Blaupunkt affords a 12-month guarantee.
If you have any questions about the guarantee, please contact your dealer. Your cash
register receipt is a valid guarantee coupon.
Traffic safety
Should the traffic situation become particularly demanding, we advise you not to use
the audio system.
Always make sure that you are still able to
hear any warning signals coming from outside the vehicle, such as police or fire engine
sirens, so that you can react accordingly.
Consequently, you should always select a
moderate volume for playing your car audio
system while you are driving.
Installation
If you would like to install your new car stereo yourself or add other audio components
to existing ones, then please read the enclosed instructions on installation and connection carefully.
54
ChicHanKanMonParis gb 95%®
54
RC 08 remote control unit
The RC 08 infrared remote
control unit allows you to
conveniently operate the
most important functions
from the steering wheel.
This remote control unit is
included with the Chicago
RCM 169 and can be ordered optionally for the other units.
International telephone information
Have you got any questions on the operation of this equipment or do you require more
information?
Give us a call!
You will find the international telephone and
fax number on the last page of this manual.
14.05.2002, 14:24 Uhr
•
Push the card in to the right as far as
possible and remove it to the front.
•
Push the operating panel back into position.
1
3
Preset button assignments, bass, treble,
balance and fader settings, Loudness, TA
(traffic announcement volume), beep volume, LOW-EQ, HIGH-EQ.
•
In addition, the settings activated before the
radio is switched off, such as the waveband,
station, TA priority, AF, REG ON/OFF,
SCANTIME, seek tuning sensitivity, ON VOL
and SHARX will also remained stored.
If a wrong KeyCard is inserted, then “CARD
ERR” will appear in the display.
This ensures that you will find your basic
settings re-adjusted automatically as soon
as you have inserted your KeyCard.
Putting the unit into operation
• Turn on the set with ON.
To insert the KeyCard, unlock the operating
panel by
• pressing 1, the operating panel will
fold down.
For safety’s sake, the operating
panel must remain locked when
the vehicle is in motion.
When you leave the vehicle, unlock the panel and remove the
KeyCard to protect the equipment
against theft.
Push the card in the direction of the arrow (2) and lock the operating panel
back into position (arrow 3).
The car radio is now ready for operation.
The system will switch off after approximately ten seconds.
“Training” a second KeyCard/
Replacing a KeyCard
If another card type is inserted (e.g. phone
or credit card), the display will show
“WRONG KC” for approximately two seconds.
When the unit is in operation with the first
KeyCard, you can “train” a second one to
be also used with the set.
Remove the wrong card and insert the correct KeyCard.
•
Press ON to turn on the set.
If you want to “train” a second KeyCard:
• Insert the first KeyCard and turn on the
set.
•
Press the DSC button and press
to select “LEARN KC”.
/
• Press << or >>.
The display will switch to “CHANGE”.
55
ChicHanKanMonParis gb 95%®
55
14.05.2002, 14:24 Uhr
ENGLISH
Press 1, the operating panel will fold
down forwards.
FRANÇAIS
•
ITALIANO
2
If you use two KeyCards, the settings stored
on the first card will be transmitted to the
second. However, you can individually store
the following functions:
To unlock the operating panel:
NEDERLANDS
If you have lost your KeyCard or if it was
damaged, you can buy a new one from your
specialised dealer.
Removing the KeyCard
SVENSKA
Insert the KeyCard with the contacts
facing down as shown in the illustration (arrow 1).
ESPAÑOL
•
PORTUGUÊS
This car radio comes equipped with one
KeyCard, but it can also be operated with a
second card.
DEUTSCH
KeyCard theft protection system
KeyCard theft protection system
•
Remove the first KeyCard and insert
the new one while “CHANGE” still appears in the display.
After the display indicates “READY” or
“LEARN KC”,
• press DSC.
Now you can also use the new KeyCard for
operating your unit.
A maximum of two cards can be used with
the set.
If you attempt “train” a third one, the access
authorisation for the KeyCard not used for
the “training” process will be deleted automatically.
Short Additional Memory
(S.A.M.)
Optical display as theft protection
The second KeyCard available from your
specialised dealer allows you to read out
short information, which will run through the
display, such as, for example, the phone
number of your car dealer or the emergency call number of your automobile association.
Flashing light diode ?
The freely selectable text with a maximum
of 162 characters can be programmed by
any dealer who has the required equipment
available.
Turn On Message (T.O.M.)
Displaying the radio pass data
You can use the KeyCard supplied with your
set to display the radio pass data such as
the model name, product number (7 6 ...)
and serial number.
Please refer to the section on “DSC programming - READ KC”.
The second KeyCard available from your
specialised dealer also allows you to display a special turn-on message each time
the radio is switched on.
The freely selectable text with a maximum
of 48 characters can be programmed by any
dealer who has the required equipment
available.
When the vehicle is stationary and the KeyCard has been removed, the light diode can
be switched to flash for extra anti-theft security.
For this it is necessary that the positive power supply line and the permanent +12 V lead
are connected such as described in the installation instructions.
Make sure that the unit is switched off; the
operating panel is unlocked; the KeyCard
has been removed; “LED ON” has been
selected in the DSC mode (factory setting).
If necessary, please refer to the section on
“DSC programming - LED”.
Switching off the flashing light
The flashing light can be switched off by
selecting “LED OFF” in the DSC menu.
Each time you turn on your system with the
second KeyCard, the programmed text will
appear in the display.
56
ChicHanKanMonParis gb 95%®
56
14.05.2002, 14:24 Uhr
•
Insert the new KeyCard into the unit
and lock the operating panel into position.
•
Press ON.
If necessary, clean the KeyCard contacts
using a cotton swab soaked in rubbing alcohol.
•
Within the next 5 seconds, press TU
and ST1. “0000” will appear in the display.
Lost or damaged KeyCard
•
Now use the rocker switch to enter the
four-digit master code in the radio
pass:
/
- Enter digits (press as often
as required)
<< / >> - Select the entry position.
Always keep the radio pass in a safe
place. Do not leave it in your vehicle.
•
Press ENT after you have entered the
correct master code.
The new KeyCard has been accepted when
the unit switches to play.
SVENSKA
If the KeyCard for your unit is lost or damaged you can train a new KeyCard.
You can purchase the new KeyCard from
any authorised dealer. You will also require
the master code for the unit, which you will
find in the radio pass.
FRANÇAIS
To ensure that the KeyCard will function
properly it is important that the contacts are
free from any foreign particles. Avoid direct
skin contact.
ITALIANO
Training the new KeyCard
NEDERLANDS
Care of your KeyCard
ENGLISH
DEUTSCH
KeyCard theft protection system
Making mistakes in the entry
PORTUGUÊS
ESPAÑOL
If you enter the wrong code, “CODE-ERR”
will appear in the display. If you enter the
wrong code three times, “WAIT 1h” will appear in the display. The unit will switch to a
standby mode for one hour.
• Switch the unit off and on again.
Repeat the steps to train the new KeyCard,
but be sure to enter the correct master code.
57
ChicHanKanMonParis gb 95%®
57
14.05.2002, 14:24 Uhr
Selecting the operating
mode
Optimising display
legibility
You can select the following operating
modes: Radio (TU), Cassette (CC) and CD
changer (CDC).
The viewing angle of the display can be altered to allow optimum legibility.
• Press DSC.
CC cannot be selected unless a cassette
has been inserted.
CDC cannot be selected unless one of the
Blaupunkt changers, the A 06, the A 072,
the A 08, the A 05, or the A 071 has been
connected and there is at least one CD in
the magazine.
•
To switch the operating mode:
• press TU, CC or CDC.
If you press TU again, the unit will switch to
menu level 2. On this level it is possible to
adjust the functions for radio operation. The
unit will switch back to menu level 1 automatically approx. eight seconds after the last
adjustment was made.
Press the lower part of the rocker
switch until “ANGLE” appears in the
display.
•
Press << / >> to set the best viewing
angle for your position.
When you have completed the setting
• press DSC.
58
ChicHanKanMonParis gb 95%®
58
14.05.2002, 14:24 Uhr
The AF (Alternative Frequency) function
makes sure that the strongest frequency of
the currently selected program is always
tuned in automatically.
Switching AF on/off:
For radio operation
• Press TU, menu level 2 will appear.
• Press the AF button briefly.
The function is activated when “AF” lights
up in the display.
“SEARCH” will disappear from the display
when the alternative frequency has been
found or after the frequency band has been
run through completely.
If the reception quality of the selected program deteriorates beyond a certain point:
• Tune into another station.
Menu level 2
•
Press the key marked REG, you can
switch to “REG ON” or “REG OFF”.
59
ChicHanKanMonParis gb 95%®
59
ENGLISH
FRANÇAIS
NEDERLANDS
AF - Alternative frequency
If “SEARCH” appears in the display when
you switch on the radio or recall one of the
stored frequencies, this indicates that the
unit is automatically searching for an alternative frequency.
To switch REG on/off:
• Press TU, menu level 2 will appear.
SVENSKA
But RDS offers you further advantages:
While searching for the strongest reception
signal, the radio may switch to mute briefly.
ESPAÑOL
When RDS is activated, the preset buttons
become program buttons. You now know
exactly which program you have tuned into,
making it easy to find the desired station
quickly.
“AF” is highlighted for the corresponding
softkey.
PORTUGUÊS
More and more radio stations have begun
to broadcast RDS information alongside
their programs.
Certain radio programs are split up at times
into regional programs offering local information. The 1st program broadcast by NDR,
for example, offers programs with different
contents in the northern states of Germany
Schleswig-Holstein, Hamburg and Lower
Saxony at certain times of the day.
If you are listening to a program and want
to continue to listen to that program, it is advisable to switch to REG ON.
If you leave the service area of the regional
program you are tuned into, or if you would
like to take advantage of the full RDS service, switch to “REG OFF”.
ITALIANO
REG - regional program
The Radio Data System offers you more
convenience when you listen to FM radio
stations.
As soon as a program has been identified,
the station name including a regional identifier, if available, will appear in the display,
for example, NDR1 NDS (regional program
in Lower Saxony, Germany).
DEUTSCH
Radio operation with RDS (Radio Data System)
14.05.2002, 14:24 Uhr
Radio operation with RDS (Radio Data System)
The setting selected will appear briefly in the
display. When the regional function has
been activated, the corresponding key will
be highlighted in the display.
Selecting a waveband
With this car radio you can select between
the following wavebands:
FM 87.5 - 108 MHz
MW 531 - 1602 kHz
LW 153 - 279 kHz
• Select the desired waveband by pressing TU, menu level 2 will appear in the
display.
Station tuning
Automatic tuning
If necessary, deactivate these functions in
menu level 2.
/
•
Press / ; the car radio will automatically search for the next station.
If you hold / on the rocker switch pressed
up or down, seek tuning will speed up in upwards or downwards direction.
•
Press << >>; the frequency will change
in short intervals downwards or upwards.
If you hold the right or left part of the rocker
switch pressed down, the frequency scan
will accelerate.
Scrolling through the broadcasting networks (FM only)
Seek tuning
Up
Down
<< Down in short intervals
(for FM only; “AF” must be switched off)
>> Up in short intervals
(for FM only; “AF” must be switched off)
Manual tuning with << >>
You can use the << >> buttons to tune into
stations in your reception area.
If it is possible to receive several programs
in the same broadcasting network, you can
scroll through them forwards by pressing >>,
or backwards by pressing <<, e.g. NDR 1,
2, 3, 4, ... . Start Travelstore:
•
Menu level 2
You can also tune into a station manually.
•
In this case:
AF and PTY must be switched off (i.e. the
symbols do not light up in the display).
Press BND (as often as required) to
select the waveband.
The radio will switch through the wavebands
as follows: FM I, FM II, FMT, MW, LW.
Manual tuning:
Press TU; menu level 2 will appear in
the display.
If “AF” does not light up,
• press AF in menu level 2.
60
ChicHanKanMonParis gb 95%®
60
14.05.2002, 14:24 Uhr
Storing stations
On FM, you can store six stations on the
preset buttons ST1 - ST6 for each of the
memory banks I, II and T.
On MW/LW, you can also store six stations
each.
• Press TU, menu level 2 will appear in
the display.
•
Press BND to select the waveband.
•
Use the rocker switch to tune into a
station (either automatically / or
manually << >>).
You can automatically store the six most
powerful FM stations in your current reception area sorted according to their signal
strength. This function is particularly convenient on longer trips.
• Press TU, menu level 2 will appear in
the display.
FM
Recall the stations on the waveband selected directly:
• by pressing ST1 - ST6.
To select a station on a different waveband:
• Press NEXT as often as necessary until the desired memory bank appears
and then select the station by pressing
ST1 - ST6.
• Press TS briefly.
“T-STORE” will flash in the display.
The six strongest FM stations will be automatically stored on the memory bank T
(Travelstore). If it is not possible to receive
six stations, the remaining presets will be
marked by four dashes. When this process
MW, LW
You can select the stations stored for the
selected waveband directly:
61
ChicHanKanMonParis gb 95%®
61
ITALIANO
Automatically storing the
strongest stations with Travelstore
You can recall any stored station at the touch
of a button.
DEUTSCH
Recalling stored stations
ENGLISH
Note:
Should you tune into a station which has
already been stored before on another memory bank, the corresponding preset button
and the memory bank will flash briefly in the
display.
NEDERLANDS
Press NEXT as often as necessary until the desired memory bank lights up
in the display.
If desired, stations can also be stored manually on the Travelstore bank (see “Storing
stations”).
SVENSKA
•
has been completed, the radio will play the
station with the strongest reception (ST 1).
ESPAÑOL
You can shift between the memory banks I,
II and T in order to store stations and recall
them later. The currently selected memory
bank is indicated in the display.
Press the desired preset button until
the radio resumes play after the muting
(takes approximately 2 seconds, confirmed by a beep).
Now the station has been stored.
14.05.2002, 14:24 Uhr
PORTUGUÊS
Changing the memory bank (FM) •
FRANÇAIS
Radio operation with RDS (Radio Data System)
Radio operation with RDS (Radio Data System)
• by pressing ST1 - ST6.
To select a station on a different waveband:
• Press NEXT as often as necessary until the desired memory bank appears
and then select the station by pressing
ST1 - ST6.
To select a scanned station and switch
off Preset Scan:
• Press SCA or the rocker switch briefly.
To select a scanned station and switch
off the Radio Scan function:
• Press SCA or the rocker switch briefly.
If you do not select a station, the scan function will automatically switch off after the frequency band has been run through completely. The unit will tune into the station you
were listening to before you started the scan
function.
Scanning stations with Radio
Scan
Changing the scan time
Scanning stored stations with
Preset Scan
You can have all of the stored stations briefly
scanned on all wavebands and in the selected FM memory bank.
Preset Scan cannot be started unless PTY
is switched off (“PTY” is not highlighted in
the display).
If necessary, switch off PTY on menu level
2. To do so
• press TU and switch off the function by
pressing the corresponding key.
To start Preset Scan:
• Press SCA for approx. 1 second.
All of the stored stations on the waveband
selected and within reception range will be
scanned one after the other. “SCAN” and
the station name or frequency will flash alternately in the display.
You can also scan all of the stations within
reception range.
Radio Scan cannot be started unless PTY
is switched off (“PTY” is not highlighted in
the display).
The scan time can be set from between five
to a maximum of 30 seconds.
Please refer to the section on “DSC programming - SCANTIME”.
Selecting the seek tuning sensiIf necessary, switch off PTY on menu level tivity
2. To do so
• press TU and switch off the function by
pressing the corresponding key.
To start the Scan function:
• Press SCA briefly.
All of the stations on the waveband selected and within reception range will be
scanned one after the other. “SCAN” and
the station name or frequency will flash alternately in the display.
You can alter the automatic seek tuning
sensitivity.
If “lo” is displayed, the radio will only pick up
strong, local stations (low sensitivity).
If “lo” does not light up, the radio will also
pick up weaker, more distant stations (high
sensitivity).
If you want to alter the sensitivity level,
please refer to the section on “DSC programming - LO/DX”).
62
ChicHanKanMonParis gb 95%®
62
14.05.2002, 14:24 Uhr
Automatic bandwidth adjustment (SHARX)
Switching PTY on/off
• Press PTY.
When the function is active, the program
type selected last will briefly appear in the
display, e.g. “SPORT”. As long as PTY is
active, “PTY” will appear permanently in the
display.
In the DSC menu, you can use the SHARX
function to adjust the bandwidth in the FM
frequency range. This can be a great advantage when there are a large number of
stations within your current reception range.
Interference with strong adjacent stations
can be reduced to an absolute minimum if
you activate SHARX ON (factory setting).
Program type
If necessary, refer to the section on “DSC
programming – SHARX”.
Use << >> to have the last selected program
type displayed and to choose a new one.
You can select any one of the stored types
The following list indicates all of the program
types which are currently available.
The letters printed in bold are identical to
the abbreviation which appears briefly in the
display.
NEWS
CURRENT AFFAIRS
INFORMATION
SPORT
EDUCATE
DRAMA
CULTURE
SCIENCE
VARIED
POP MUSIC
ROCK MUSIC
EASY MUSIC
LIGHT MUSIC
CLASSICS
OTHER MUSIC
WEATHER
FINANCE
CHILDREN’S PROGRAMS
SOCIAL AFFAIRS
63
ChicHanKanMonParis gb 95%®
63
14.05.2002, 14:24 Uhr
ENGLISH
FRANÇAIS
You can use DSC to select German, English or French as the language used in the
display (refer to the section on “DSC programming – PTY LANG”).
ITALIANO
The mode selected is indicated briefly in the
display.
Requirement: PTY must be active.
NEDERLANDS
If you would like to switch to mono, refer to
“DSC programming - STEREO/MONO”.
PTY is an RDS service which an increasing
number of broadcasting stations have begun to offer. This feature allows you to select FM stations according to their program
type. After you have chosen the PTY of your
preference, the corresponding stations can
be selected either by seek tuning or using
the scan function.
SVENSKA
The unit will automatically switch to mono if
the signal received is not strong enough for
stereo playback.
with the preset buttons 1-6.
ESPAÑOL
If reception is poor, you may get better
sound quality by switching from stereo to
mono in the DSC menu. Each time the radio is switched on, stereo playback is activated automatically.
PTY - Program Type
PORTUGUÊS
Switching from stereo to mono
(FM)
DEUTSCH
Radio operation with RDS (Radio Data System)
Radio operation with RDS (Radio Data System)
RELIGION
PHONE IN
TRAVEL
LEISURE
JAZZ MUSIC
COUNTRY MUSIC
NATIONAL MUSIC
OLDIES MUSIC
FOLK MUSIC
DOCUMENT
a) Using the preset buttons
Checking the program type of the station
• press / to start the seek tuning
function.
If the radio is unable to find a station offering the selected program type, the display
will show “NO PTY” and a beep tone will be
emitted. The radio will select the station
which was tuned into before seek tuning was
activated.
• During this period press >> (forwards) or << (backwards) to select
the desired type.
When PTY is switched on, you can use
the preset buttons ST1 - ST6 to select
the program types stored at the factory.
• Press << or >> as many times as required.
If you would like to listen to a station
with the selected PTY,
• Press one of the presets 1-6.
The selected program type will be displayed for 2 seconds.
If you would like to listen to a station
with this PTY,
On menu level 2
• Press PTY for approx. 2 seconds.
After the beep tone the display will show the
program type offered by the station currently playing.
If “NONE” appears in the display, the current station has no PTY code.
Displaying the selected program type
• Press << or >>.
The program type selected last will be displayed briefly.
Selecting a program type
You can assign different program types to
each preset position. Please refer to the next
section on “Storing program types”.
b) Using the << >> buttons on the rocker
switch
When PTY is switched on, you can select a program type using buttons
<< >>.
• Press << or >>; the program type selected last will be displayed for 3
seconds.
• press / to start the seek tuning
function.
If the radio is unable to find a station offering the selected program type, the display
will show “NO PTY” and a beep tone will be
emitted. The radio will select the station
which was tuned into before seek tuning was
activated.
Storing program types
Each of the preset buttons ST1 - ST6 has
been assigned one program type at the factory.
If desired, you can also replace these with
other available program types.
To do so, make sure that “PTY” lights up in
the display.
• If necessary, press the PTY button to
switch on the function.
•
Select a program type using buttons
<< >> and
•
hold down the desired preset button
(ST1-ST6) until you hear a beep.
64
ChicHanKanMonParis gb 95%®
64
14.05.2002, 14:25 Uhr
As soon as it is possible to receive a program in the broadcasting network with the
PTY selected, the radio will switch over to
the corresponding station for the duration
of the program.
Note:
As already mentioned, these functions are
not supported by all of the RDS stations at
the present time.
Scanning stations with PTY SCAN
Situation:
PTY is switched on and lights up in the display.
No station offering the selected program
type can be found currently in your reception range (with seek tuning or scan).
The set will switch back to the station previously tuned into.
“PTY” lights up in the display.
-
Program type “POP” selected.
-
Seek tuning is started.
-
No station with “PTY-POP” can be
found.
-
The display shows “NO PTY” and
-
automatically switches back to NDR3.
-
NDR2 airs a “PTY-POP” program.
-
The radio will switch to the linked station NDR2 for the duration of the
“POP” program.
FRANÇAIS
-
NEDERLANDS
ITALIANO
Station playing: NDR3.
SVENSKA
PTY priority
-
During CD operation, the set will also switch
to the program offering the selected PTY
within the broadcasting network.
ESPAÑOL
To switch off PTY-SCAN:
• Press SCA or the seek-tuning rocker
switch once again.
After the entire waveband has been
scanned, the PTY-SCAN function will be
turned off automatically.
Example: German broadcasting network
NDR:
After the PTY program has ended the system will switch back to the previous mode
(radio or CD).
PORTUGUÊS
Requirement: “PTY” must appear in the display.
• Press the SCA button.
All of the stations in your current reception
area offering the selected program type will
be scanned.
65
ChicHanKanMonParis gb 95%®
65
DEUTSCH
Now the selected program type can be recalled by pressing this preset when PTY has
been activated. (“PTY” appears in the display.)
ENGLISH
Radio operation with RDS (Radio Data System)
14.05.2002, 14:25 Uhr
Traffic information station reception with RDS-EON
The abbreviation “EON” stands for Enhanced Other Networks, which means that
information is exchanged within a radio network.
Many FM radio stations provide their service area with traffic messages at regular intervals.
Along with their programs, all traffic information stations transmit a special carrier
signal, which is decoded by your car radio.
If this signal is identified, “TP” will appear in
the display (Traffic program).
In addition to these, there are also stations
which do not actually transmit traffic information themselves, but by using RDS-EON
it is possible for them to forward the traffic
messages broadcast by another traffic information station in the same radio network.
If you want to have the priority for traffic announcements activated while listening to
one of these stations (e.g. NDR3), “TA” must
appear on the display panel.
If a traffic announcement is broadcast, the
radio will automatically switch to the linked
traffic program station (in this case, NDR2)
for the duration of the message and return
to the original program (NDR3) afterwards.
Traffic announcement priority
on/off
If the priority for traffic announcement programmes is activated, “TA” will light up in
the display.
To switch the priority on or off:
• Press the TA button.
If you press TA while a message is being
broadcast, this message will be interrupted.
The unit will then switch back to the previous mode. The priority for other traffic messages remains active.
Please note that several buttons have no
function while a traffic announcement is
broadcast.
Warning beep
If you leave the reception area of the traffic
information station you are currently tuned
into, you will hear a warning beep at intervals of approx. 30 seconds.
• press a preset button which has a
traffic information station allocated to
it.
Or:
b) Switch off the priority for traffic announcements:
• Press TA.
“TA” will disappear from the display.
Automatic search function
(Cassette operation)
If you are listening to a cassette and you
leave the reception area for the traffic information station you have selected, then the
car radio will automatically search for a new
traffic information station.
If the radio is unable to find a traffic information station within 30 sec. after the station search has started you will hear a beep
every 30 sec. to alert you to this situation.
Proceed as described above to switch off
the beep.
This warning beep will also be emitted if you
press a preset button for a station which
does not send the traffic information signal.
Adjusting the volume for traffic
announcements and the warning
beep
Switching the warning beep off
This volume was preset at the factory, but
you can use the DSC function to alter the
setting as desired (see “DSC programming
- TA VOL”).
a) Tune into another station offering traffic information:
• Press the rocker switch or
66
ChicHanKanMonParis gb 95%®
66
14.05.2002, 14:25 Uhr
•
Switch on the car radio and release the
operating panel by pressing 1.
The operating panel will fold down forwards.
Selecting the display mode
•
You can switch the display mode during
cassette operation.
ITALIANO
Press CC, the cassette functions will
appear in the display.
•
Press DIS briefly.
The display mode selected will appear
briefly in the top line of the display.
•
Press DIS as often as necessary until
the desired display mode appears.
Dolby B NR*
Removing a cassette
•
With the operating panel in the folddown position, press the Eject button
(arrow) briefly.
The cassette will eject.
To prevent damage to the mechanism, do
not attempt to stop or force a cassette while
it is being inserted or ejected.
This unit can play cassettes which have
been recorded with Dolby B NR or without
the use of noise suppression.
Cassettes which have been recorded with
Dolby B NR* exhibit significantly less tape
noise as well as much greater sound dynamics.
is highlighted
Dolby B NR is active when
in the display.
“COUNTER” – tape counter
“CLOCK”
– time
“ELAPSED” – elapsed playing time for
the tape side
“REMAIN”
– remaining playing time on
the tape side
67
ChicHanKanMonParis gb 95%®
67
NEDERLANDS
Grasp the left-hand side of the operating panel to fold it back up and lock it
into place.
A cassette is inserted, “CC-IN” appears in
the display.
SVENSKA
•
Switching on cassette operation
ESPAÑOL
Insert the cassette with Side A or 1
facing up without the use of force.
The cassette will automatically be transported to its playing position. Cassette playback
will begin.
* The noise reduction system manufactured under licence by the Dolby Laboratories Licensing Corporation. The word DOLBY and the double-D symbol are
trademarks of the DOLBY Laboratories.
14.05.2002, 14:25 Uhr
PORTUGUÊS
•
Switching Dolby B NR on/off:
• press .
ENGLISH
For safety’s sake, the operating
panel must always be returned to
the locked position while you are
driving.
FRANÇAIS
Inserting a cassette
DEUTSCH
Cassette operation
Cassette operation
This unit is equipped with a real-time
counter which calculates the current
playing time.
After a new cassette has been inserted, the real-time counter will switch to
a synchronisation phase briefly. During
this time, SYNC will appear in the display. The synchronisation phase may
vary in length for ELAPSED or
REMAIN.
Scanning cassette titles with
SCAN
Selecting titles with S-CPS
It is possible to scan the titles on a cassette.
As soon as you find a title you like, you can
end SCAN. This title will then continue to
play.
To repeat and skip cassette titles.
(Super Cassette Program Search)
SCAN is active when “SCA” is highlighted
in the display. “SCAN” will also appear in
the top line of the display.
/
Track reverse
To change the track during playback:
• Press REV.
When the tape reaches the end of a side it
will automatically switch to the other side
(autoreverse). “SIDE A” will appear in the
display for track 1 and “SIDE B” for track 2.
Note:
If there is too much tension on the tape while
it is playing, it may switch to the opposite
track before it has reached the end. Check
to see if the tape is wound correctly. It often
helps to rewind the cassette completely.
Starting/ending SCAN:
• Press SCA briefly.
To ensure that this function works properly,
there must be a pause of at least 3 seconds
between titles.
The scan time is set to 10 seconds at the
factory and can be altered from 5 to 30 seconds. If necessary, refer to the section on
“DSC programming - SCANTIME”.
Select title
Forwards (CPS-FF ..)
Back (CPS-FR ..)
It is possible to skip up to 9 titles. To do so,
• press / on the rocker switch as often as required.
The number of titles to be skipped will appear in the display.
Make any corrections by pressing the opposite key ( / ).
Press REV to stop this function immediately.
To ensure that this function works properly,
there must be a pause of at least 3 seconds
between titles.
68
ChicHanKanMonParis gb 95%®
68
14.05.2002, 14:25 Uhr
Switching Repeat on/off:
• Press RPT, the active function will appear briefly in the top line of the display (RPT ON/OFF).
To ensure that this function works properly,
there must be a pause of at least 3 seconds
between titles.
Fast tape forward/rewind
Switching Radio Monitor on/off:
• Press RM, the activated function will
appear briefly in the top line of the display (RM ON/OFF).
Automatically skipping over
blank portions of the tape with
Blank Skip (BLS)
against dirt, dust and temperatures over
50 °C. Allow cold cassettes to warm up
somewhat before playing them to ensure
that the tape plays smoothly. Malfunctions
in playback or sound may be caused by dirt
build-up on the pinch roller and the audio
head after approx. 100 hours of operation.
To remove normal dirt build-up clean the
equipment with a cleaning cassette. In more
stubborn cases, use a cotton swab dipped
in rubbing alcohol. Never insert hard instruments into the tape deck.
As soon as there is a break of more than 10
sec. during cassette playback, the fast forward function will be activated automatically to move to the next title.
The Blank Skip function is active when “BLS”
appears highlighted in the display.
PORTUGUÊS
ESPAÑOL
Switching Blank Skip on/off:
• Press BLS, the activated function will
appear briefly in the top line of the display (BLS ON/OFF).
>> Fast forward
<< Fast rewind
Press REV to end fast forward or rewind.
69
ChicHanKanMonParis gb 95%®
69
DEUTSCH
NEDERLANDS
The Repeat function is active when “RPT”
is highlighted in the display.
You can listen to the radio while fast forwarding or rewinding the tape (for CPS as
well) instead of switching the sound to mute.
The Radio Monitor function is active when
“RM” appears highlighted in the display.
SVENSKA
will repeat until RPT is switched off. The
Repeat function will end automatically when
the cassette is removed or the unit is
switched off.
ENGLISH
Listening to the radio while fast
Care instructions
forwarding or rewinding the tape You should use only C60/C90 tape caswith Radio Monitor (RM)
Repeats the title currently playing. This title
settes in your car. Protect your cassettes
RPT = Repeat
FRANÇAIS
Repeating titles with RPT
ITALIANO
Cassette operation
14.05.2002, 14:25 Uhr
Changer operation
You can use this car radio to conveniently
control CD playback on a Blaupunkt CD
changer.
The following CD changers can be connected directly: CDC A 06, A 072, A 08.
The CD changers A 05 and A 071 can be
connected with the adapter cable 7 607 889
093.
The CDC A 08 is included with the Hannover 2000 DJ / Kansas DJ.
Use only standard circular CDs measuring 12 cm in diameter!
CDs measuring 8 cm in diameter or
CDs in different shapes such as a butterfly or beer mug are not suitable for
playback using this equipment.
This is very likely to result in the destruction of the CD or the CD drive.
We assume no liability for damage to
the equipment caused by playing unsuitable CDs.
Switching on CD changer operation
Make sure that at least one CD has been
inserted into the magazine.
• Press CDC, the CDC functions will appear in the display (track number,
name/playback time).
Also refer to the section on “Enter CD
names”.
Selecting CDs and tracks
You can use the rocker switch to conveniently select other CDs, tracks or passages.
Selecting the CD
up
down
The numbers of the available CDs will appear in the display.
Selecting the display mode
During CD changer operation you can switch
the display mode.
•
Press DIS repeatedly until the desired
display mode appears.
“CD10 T3” – CD and track number;
“00:20”
Elapsed playing time
“VIVALDI”
“T3”
up
down
If you press only once, the track currently
playing will start again.
Selecting the track
Fast forward, audible (CUE).
Hold >> pressed down for as long as necessary.
– CD name
Track number
“CD10 T3” – CD and track number;
“14:34”
Clock
The CD name can only be displayed if you
have actually entered one before.
Fast rewind, audible (REVIEW).
Hold << pressed down for as long as necessary.
70
ChicHanKanMonParis gb 95%®
70
14.05.2002, 14:25 Uhr
- REP TRCK = Repeat track
- REP CD = Repeat CD
- RPT OFF = Repeat function off
•
TPM
(Track Program Memory)
Stores and plays your favourite tracks. It is
possible to manage up to 99 CDs with up to
40 tracks.
Storing tracks with TPM
A track can only be stored while it is playing.
To store a track
• press TPM for approx. 1 second, “TPM
a
o
m
P
g
ru
m
n
e
g
ri PROG” will appear in the display.
This track has been stored.
If “TPM” is highlighted in the display, this
means that TPM playback is active. All of
the tracks on the CD stored in this operating mode will be played. If you activate SCA
(scan) as well, these tracks will be scanned.
TPM playback cannot be activated unless
you have already stored tracks with the TPM
function.
PORTUGUÊS
Press RPT as many times as necessary until you have selected the desired setting.
The CD or the track will repeat until you
press RPT to switch off the function with
“RPT OFF”.
mit
D
S
C
ChicHanKanMonParis gb 95%®
71
71
DEUTSCH
You can use TPM to delete stored tracks. If
you want to delete the CD names at the
same time, please refer to “Deleting CD
names/TPM with DSC UPDATE”.
TPM tracks can only be deleted during playback.
• Switch on TPM.
“TPM” will be highlighted in the display.
In this case, “CLR” will appear below
TPM.
If you would like to delete the track playing
•
press CLR for approx. 2 seconds,
“TRCK CLR” will flash briefly in the display.
If you would like to delete all of the tracks
on the CD playing
•
press CLR for approx. 5 seconds,
“DISC CLR” will flash briefly in the display.
If you would like to delete all of the tracks
on all of the CDs in the magazine in changer operation
•
press CLR for approx. 8 seconds,
“ALL CLR” will flash briefly in the display.
Press TPM briefly. The mode selected
will appear briefly in the display (TPM
ON/OFF).
ENGLISH
•
FRANÇAIS
Deleting the TPM memory
ITALIANO
You can repeat a track or a CD as often as
desired. Use the RPT key to select the following functions:
Switching TPM playback on/off
NEDERLANDS
RPT = Repeat
SVENSKA
Repeat tracks/CDs with RPT
ESPAÑOL
Changer operation
14.05.2002, 14:25 Uhr
Changer operation
MIX
SCAN
You can have the CD tracks played in random order. The MIX function is active when
“MIX” is highlighted in the display.
Use this function to scan all of the CD tracks.
You can choose the following MIX functions:
MIX CD
The tracks on the selected CD will be played
in random order. The next disc will be selected in numerical order. MIX (random order) applies to the playback of the tracks.
MIX MAG
CDC A 08: All tracks on the CDs in the magazine will be played in random order.
CDC A 06 / 072: The CDs in the magazine
are selected at random and then the tracks
on the CD selected are played in random
order.
MIX OFF
The Mix function is deactivated. Discs and
titles will be selected in numerical order.
To alter the setting:
•
Press MIX briefly, the function selected
will appear briefly in the display.
•
To start the Scan function:
• Press SCA briefly, the display will indicate “SCAN”.
The titles will be scanned one after the other in ascending order.
To stop the Scan function:
• Press SCA once again briefly.
The track currently scanned will continue to
play.
SCAN will also stop if you press the
rocker switch, MIX, RPT, DSC, AUD,
TU or CC.
Entering CD names
In the changer mode you can give up to 99
CDs an individual name.
The specified name (e.g. VIVALDI) will appear in the display if you have selected the
corresponding display mode with DIS.
Use the rocker switch / to select the
first character.
The capital letters A to Z, the numbers 0 to
9 and special characters will be listed one
after the other.
• Use the rocker switch << >> to move
to the next position and select a character.
You can select up to 7 characters in this way.
Once you have completed the name as desired:
• Press ENT in order to store it.
If you would like to name another CD,
• press <</>> and use / to select the
next CD you want to name in the magazine.
You can change a name by entering and
storing a different one (overwrite).
If you would like to finish your entry,
• press DSC to quit the DSC menu.
To start the entry:
• Press the DSC button and press /
as often as necessary until “CDNAME” appears in the display.
• Press << >>.
The position for the first character will begin
to flash.
72
ChicHanKanMonParis gb 95%®
72
14.05.2002, 14:25 Uhr
Use the DSC UPD (update) feature to delete the CD names and the TPM at the same
time.
To return to “CD UPDATE” in the DSC menu
without deleting the CD names and TPM:
• Press ENT.
ENGLISH
Deleting CD names/TPM with
DSC UPDATE
DEUTSCH
Changer operation
FRANÇAIS
You can delete the name stored for the CD
in the CD drive and its TPM with “CLR
DISC”.
Use “CLR ALL” to delete the names and
TPM for all of the CDs.
Press DSC.
Press / as many times as required
until “CD UPDATE” appears in the display.
•
Press >> to select “CLR DISC” if you
want to delete the name and TPM of
that CD,
NEDERLANDS
•
•
ITALIANO
Insert a CD whose data you would like
to delete (name and TPM).
SVENSKA
•
or
Press << to select “CLR ALL” to delete
the names and TPM stored for all of
the CDs.
ESPAÑOL
•
Press ENT for approx. 1 second.
“DELETING” will appear briefly in the
display.
The deletion process is complete.
PORTUGUÊS
•
73
ChicHanKanMonParis gb 95%®
73
14.05.2002, 14:25 Uhr
Clock - Time
This car stereo is equipped with a built-in
clock which automatically takes advantage
of RDS to ensure highly accurate time-keeping (hours, minutes).
Displaying the clock
For the clock to function properly with RDS,
an RDS station with the CT function (CT –
clock time) must be received.
Radio mode:
The automatic correction of the time can be
switched off.
You can set the clock to permanent display
in both the radio and CD modes.
You can switch between clock display and
waveband (incl. memory bank for FM). To
do so
• press DIS for approx. 2 seconds.
Cassette operation:
Setting the clock
You can select from four different display
modes.
a) automatically
The clock is set automatically when the
radio is tuned into an RDS station
which has the “CT” function (clock
time).
b) manually with DSC-CLOCKSET
• Press DSC briefly, “CLOCKSET” will
appear in the display.
• Press << >> to set the hours/minutes. You can move to a different position by pressing / .
• After you have set the clock, press
ENT briefly to store the new setting.
To switch to the clock
• press DIS repeatedly until CLOCK appears in the top line of the display.
Changer operation:
You can select from three different display
modes.
To switch to the clock
• press DIS as often as necessary.
The time will be set automatically by RDSCT, but can also be adjusted manually if
desired.
You need only set the time manually if it is
not possible to receive an RDS station with
CT (clock time).
If you want to set the time manually, refer to
the section on “DSC programming - CLOCKSET”.
Deactivating the hour correction
function
In the DSC menu it is possible to switch off
the hour correction function with “CLK MAN/
CLK AUTO”. An automatic correction for
minutes will continue to take place.
This is useful if you would like to display the
time for a different time zone, for example.
If necessary,
• Press DSC briefly and
•
Correcting the clock after the
power has been disconnected
If the radio has been disconnected from its
power source for a longer period of time,
“0:00” will appear in the display when it is
re-connected.
Press / as often as required until
“CLK MAN/CLK AUTO” appears in the
display.
To deactivate the hour correction function
press << >> to select “CLK MAN”.
74
ChicHanKanMonParis gb 95%®
74
14.05.2002, 14:25 Uhr
As a result, the bass sounds may be lost or
reverberate, the mid-range tones sound too
overpowering and music instruments or
voices may be distorted or the total sound
quality may be completely lifeless.
The overall sound quality can be greatly
enhanced if certain frequencies are suppressed or boosted.
This car stereo is equipped with 2 parametric filters. The first filter “LOW EQ” can be
set from 32 to 500 Hz, the second filter
“HIGH EQ” from 630 to 10000 Hz. In this
context, parametric means that it is possible to set the frequency and either boost or
reduce it (+10 to –20 dB) individually for
each of these filters.
These parametric filters can be adjusted to
very exact settings even without the help of
measuring instruments.
We recommend that you use a music cassette/CD which you are familiar with to adjust the filters. The cassette/CD should include different types of musical instruments
and vocals. Purely electronic music is not
well suited to serve as a basis for making
the settings because the original sounds
cannot be determined.
Before you set the equaliser, set bass, treble, balance and fader to “0”.
This setting is described in the Quick Reference under 8 AUD.
Press DSC.
Press / as often as necessary until
“HIGH EQ” or “LOW EQ” appears in
the display.
•
Press << or >> once and
•
Set the level in the following table by
pressing / .
•
Press << >> to switch the frequency
range.
• Press ENT to store your settings.
You can switch the equaliser on and off by
pressing AUD for approx. 2 seconds.
Now you can compare the sound produced
by your car stereo with and without the
equaliser.
Now listen to the cassette/CD you have selected.
Setting recommendations on the
Internet
Evaluate the sound according to your own
personal preferences.
Refer to our home page on the Internet
Now refer to “Sound impression/problem” in
the table and you will find suggestions to
eliminate any problems under “What to do”.
to find setting recommendations for new
vehicles on the market.
http://www.blaupunkt.de
Make the settings for bass and the lower
mid-range tones with the LOW EQ filter,
75
ChicHanKanMonParis gb 95%®
75
14.05.2002, 14:25 Uhr
DEUTSCH
ENGLISH
•
•
ITALIANO
Even the sound produced by well selected
and installed speakers can be affected negatively by resonance frequencies in the vehicle interior.
The following notes are intended as recommendations only. They do not necessarily
reflect your own personal sound preferences.
NEDERLANDS
Notes on making the settings
The “HIGH EQ” and “LOW EQ” filters can
be set in the DSC menu:
SVENSKA
Position, installation and the rear volumes
of, for example, the door or rear window
shelf all play an important role.
select HIGH EQ for treble and mid-range
tones.
ESPAÑOL
The individual steps you have to take to
make these settings are described in the
table.
PORTUGUÊS
The acoustic characteristics of the car interior affect the quality of the sound reproduced in your vehicle to a much greater extent than the speakers.
FRANÇAIS
Setting the equaliser
Setting the equaliser
Assistance in setting your equaliser
Start to make your settings in the mid-range/treble and end it with the bass range.
Frequency range
Sound impression/problem
What to do
Notes
Bass
30 – 100 Hz
Bass reproduction too weak
Boost the bass with the
“LOW EQ” filter
Frequency: 50 to 100 Hz
Level: +4 to +6 dB
Avoid distortion.
Boost the level carefully if the
speaker diameter is too small.
Unclear bass
Playback reverberates
Unpleasant pressure on the ears
Reduce the lower mid-range
with the “LOW EQ” filter
Frequency: 125 to 400 Hz
Level: approx. –4 dB
The tone may become too lean
and aggressive.
Pay attention to the underlying
tone of the music.
Sound appears to be too much in
the foreground, very aggressive,
no stereo effect
Reduce the mid-range with
“HIGH EQ” filter
Frequency: 1000 to 2500 Hz
Level: -4 to –6 dB
Playback should not be too
quiet.
Tone too powerless.
Lifeless reproduction
Lack of transparency
Instruments do not sparkle
Boost treble range with
“HIGH EQ” filter
Frequency: approx. 10 kHz
Level: +2 to +4 dB
Avoid a piercing type of tone.
Strong hissing sound unpleasant.
Lower mid-range
100 – 400 Hz
Mid-range sound
400 – 4000 Hz
Treble
4000 to 20000 Hz
76
ChicHanKanMonParis gb 95%®
76
14.05.2002, 14:25 Uhr
Select function
Adjust/recall value
TA VOL
To adjust the traffic announcement and warning
beep volume from between
0 to 66.
The message will then come
through at this volume, if the
standard volume is lower.
If the standard volume is set
higher than the TA VOL level, then the traffic report will
be played at the standard
volume.
HICUT
Interference-related cut in
the treble sound. Cuts the
treble when interference occurs. Can be adjusted from
NO HICUT (OFF) to HICUT
3 (highest setting). Which
setting is the most pleasant
is a matter of personal preference.
DEUTSCH
Switches the bandwidth in
the FM frequency range.
When there are a large
number of stations within
your current reception
range, use << >> to switch
to SHARX ON which will
prevent most interference
from adjacent radio stations.
This function has been set
to “SHARX ON” at the factory.
ENGLISH
SHARX
FRANÇAIS
Equaliser setting:
To activate the frequencies
and set the level for the upper frequency range.
Refer to the detailed instructions in the section on
“Equaliser setting”.
Appears during changer operation only.
Use this function to name
your CDs. (See “Entering
CD names”)
ITALIANO
HIGH EQ
CD NAME
NEDERLANDS
Equaliser setting:
To activate the frequencies
and set the level for the lower frequency range.
Refer to the detailed instructions in the section on
“Equaliser setting”.
PORTUGUÊS
/
<< / >>
LOW EQ
SVENSKA
The car stereo has been equipped with DSC
(Direct Software Control) to allow you to
customise certain programmable, basic settings to suit your personal needs and preferences and then store them.
The basic settings for this audio equipment
were made at the factory.
In the following you can find an overview of
these settings, so that you can always reset
to them if desired.
If you wish to alter any of the programming,
• press DSC.
Use the rocker switch and the ENT button
to select and adjust the functions de-scribed
in the following. The display will show you
the setting you have selected.
ESPAÑOL
DSC programming
77
ChicHanKanMonParis gb 95%®
77
14.05.2002, 14:25 Uhr
DSC programming
LO/DX
To adjust the seek tuning
sensitivity.
“LO” stands for local reception.
“DX” stands for distant reception.
Select “LO 3” if you want to
receive strong stations in
the local area, select “DX 1”
if you want to tune into
weaker stations which are
further away.
STEREO/MONO
Switch modes by pressing
<< >>.
The mode selected will appear briefly in the display.
The radio will begin with
STEREO playback each
time it is switched on.
CLOCKSET To set the clock manually.
Press << >> to set the
hours/minutes. Move to the
next flashing position by
pressing / . To store the
setting selected, press ENT
briefly.
Also refer to the section on
“CLOCK”.
CLK AUTO/MAN
Switches the hour correction
function on/off. Read the information in the section on
“Clock, Deactivating the
hour correction function”.
12/24H MODE
Select the clock display
(12 or 24-hour display)
The volume can be adjusted
from between 0 to 9.
(0 = off)
DIM DAY
Use this function to select
the display brightness for
the daytime (from 1 to 9).
DIM NIGHT
Use this function to select
the display brightness for
the night-time (from 1 to 9).
CLK ON/OFF The clock display will appear when the ignition is
switched on, but the car
stereo is switched off. In this
case, set CLK ON.
ON VOL
BEEP
Use this function to select
the volume at which the radio is set when it is switched
on.
Adjust the desired volume
level with << >>.
When adjusted to “LAST
VOL”, the system will come
on at the volume selected
before it was switched off.
The brightness changes accordingly when the car
headlights are switched
on/off.
ANGLE
Adjusts the display to the individual viewing angle.
SCANTIME
Use this function to set the
scan time for the radio or
CD player from 5 to 30 seconds.
PTY LANG
Select the language used
for program type identification:
German, English or French.
Acknowledgement tone for
all functions which require a
button to be pressed for
more than one second.
78
ChicHanKanMonParis gb 95%®
78
14.05.2002, 14:25 Uhr
To read out the KeyCard
data.
The card supplied with the
radio is used to display the
model name, type number
(7 6 …) and the serial
number.
With the extra card it is possible to display data entered
by your specialised dealer.
NEDERLANDS
PEAK ON/OFF
Switches the dynamic level
display for the volume on/
off.
TOM ON/OFFIf you have a second KeyCard with a Turn-On Message, you can switch off this
information with “TOM
OFF”. The factory setting is
“TOM ON”.
For more information refer
to “ KeyCard theft protection
system” - “Turn ON Message (T.O.M.)”.
79
ChicHanKanMonParis gb 95%®
79
14.05.2002, 14:25 Uhr
DEUTSCH
ITALIANO
To quit the DSC programming mode and
store the adjustment:
• Press DSC.
ENGLISH
Allows you to delete CD
names during changer operation to make room for new
CDs. (Refer to “Deleting CD
names with DSC-UPDATE”.)
SVENSKA
READ KC
To “train” a second KeyCard.
Please read the information
in the section on “KeyCard
theft protection system” “Training a second KeyCard”.
LED ON/OFF Here you can choose between LED ON or LED OFF.
With LED ON, the “ON”
knob will flash for extra antitheft protection when the
unit has been switched off
and the KeyCard removed.
UPDATE
ESPAÑOL
LEARN KC
(See the section on “Short
Additional Memory S.A.M.”).
If you remove the KeyCard
during the reading process,
“READ KC” will appear on
the display panel.
PORTUGUÊS
AUX ON/OFF (for Kansas DJ, Chicago
RCM 169)
This menu item will not appear unless a CD changer
has been connected to the
system. The factory setting
is “OFF”.
If another system component is connected to AUX,
this setting must be altered
to “AUX ON”.
FRANÇAIS
DSC programming
DSC programming
Specifications
Overview of the DSC factory settings
Amplifier
LOW EQ
HIGH EQ
TA VOL
CD NAME
SHARX
HICUT
LO / DX
STEREO/MONO
CLOCKSET
CLK AUTO / MAN
12/24H MODE
CLK ON/OFF
ON VOL
BEEP
DIM DAY
DIM NIGHT
ANGLE
SCANTIME
PTY LANG
AUX
LEARN KC
READ KC
LED
PEAK ON/OFF
TOM ON/OFF
UPDATE
0 dB/40 Hz
0 dB/630 Hz
35
SHARX ON
HICUT 2
DIST 1
STEREO
0:00
CLK AUTO
24H MODE
CLK OFF
LAST VOL
3
9
9
0
10 sec.
DEUTSCH
OFF
ON
ON
ON
-
Output power:
4 x 25 W RMS power
acc. to DIN 45324 at
14.4 V
4 x 40 W max. power
Tuner
Wavebands:
FM
:
MW
:
LW
:
FM sensitivity:
87.5 - 108 MHz
531 - 1602 kHz
153 - 279 kHz
0.7 µV at 26 dB
signal-to-noise ratio
FM frequency response:
20 - 16000 Hz
Tape
Frequency
response:
30 - 19000 Hz
Subject to modifications!
80
ChicHanKanMonParis gb 95%®
80
14.05.2002, 14:25 Uhr
AUD – Audio
Sound settings for bass and treble, balance
(left/right) and fader (front/rear).
Autoreverse
See Reverse.
BLS – Blank Skip
Automatically skips longer portions of blank
tape during cassette operation, e.g. at the
end of the tape.
BND (Band)
Switches between wavebands and memory banks.
DSC – Direct Software Control
Equalizer
Adjusts the frequencies to the acoustic conditions and personal tastes.
EXIT
Press to end/cancel a setting.
With the help of DSC it is possible to adjust
the basic factory settings to your own personal preferences.
Real-time counter
KeyCard
Theft protection system from Blaupunkt. The
car stereo cannot be operated without the
correct KeyCard.
Provides a precise calculation of the current
playing time.
MIX
CD changer
ENT (Enter)
MUTE
CL – Clear
Press briefly to accept/store settings.
Switches audio off
Changer
CDs/CD tracks are played in random order.
PORTUGUÊS
Returns to the previous menu item.
81
ChicHanKanMonParis gb 95%®
81
DEUTSCH
The noise reduction system manufactured
under licence by the Dolby Laboratories Licensing Corporation.
The word DOLBY and the double-D symbol
( ) are trademarks of the DOLBY Laboratories.
Cassettes which have been recorded with
Dolby B NR* exhibit significantly less tape
noise as well as much greater sound dynamics.
Amplifies the output power.
Dolby B NR
ENGLISH
Amplifier
ITALIANO
Repeats and skips cassette titles. Use SCPS to select specific cassette titles.
NEDERLANDS
In RDS this function ensures that the radio
always tunes into the frequency with the best
reception for the station.
EON – Enhanced Other Network
In RDS, EON makes it possible to exchange
station information within a station network.
Traffic information, for example, can be forwarded automatically from a traffic information station to a station which does not
broadcast traffic information in the same
network. After the traffic announcement has
been put through, the radio switches back
to the original station.
SVENSKA
CPS – Cassette Program Search
ESPAÑOL
AF - Alternative Frequency
FRANÇAIS
Glossary - Technical Terminology
14.05.2002, 14:25 Uhr
Glossary - Technical Terminology
Preset Scan
Reverse
See Scan
Switches the tape running direction during
cassette playback.
Autoreverse automatically switches to the
other side at the end of the tape.
PTY
Designed for the selection of a specific type
of program in FM (e.g. sports, news). Also
see RDS.
RDS – Radio Data System
Service provided by radio stations to enhance radio listening pleasure.
The station name, for example, is displayed
instead of the frequency.
Other RDS functions include:
AF – Alternative Frequency
EON – Enhanced Other Networks
Radio text
REG – Regional program
PTY – Program type
TA – Traffic Announcement
TP – Traffic Program
REG
TA - Traffic Announcement (priority for traffic information)
“TA” in the display indicates that the priority
for traffic announcements has been
switched on. Also see RDS.
RM – Radio Monitor
TP - Traffic Program
Automatically switches to radio playback
while the tape is fast forwarding or rewinding.
“TP” in the display indicates that the radio is
tuned into a station which broadcasts traffic
information. Also see RDS.
RPT (Repeat)
TPM – Track Program Memory
Repeats CD tracks. In changer operation
you can repeat single tracks or complete
CDs.
Stores and plays your favourite tracks in CD
or changer mode.
SCAN
Automatically stores the stations with the
best reception on the station preset buttons.
Very useful during trips.
Briefly plays the radio stations in your current reception range or the tracks on a CD
in CD mode. Using Preset Scan you can
scan the radio stations stored on the preset
buttons.
TS – Travelstore
S-CPS – Super Cassette Program Search
Regional programs have priority. REG ON
stops the radio from automatically switching to a different regional program broadcast by the same station because it has
better reception. Also see RDS.
See CPS.
Softkey (Software key)
Key with varying functions
82
ChicHanKanMonParis gb 95%®
82
14.05.2002, 14:25 Uhr
F
Care instructions (Cassette) 69
Care of your KeyCard 57
Cassette operation 67
Changer operation 70
Changing the memory bank 61
Clock 74
CODE-ERR 57
CPS 68
Operating mode 58
Operating panel is unlocked
Optimising display 58
G
Damaged KeyCard 57
Deleting CD names 73
Deleting TPM 73
DIS 50
Preset Scan 62
Program type 63
PTY 63
PTY priority 65
PTY SCAN 65
H
HICUT 77
I
K
KeyCard
55
45
P
Glossary 81
Guarantee 54
Installation 54
International telephone information 54
D
ENGLISH
O
Factory settings 80
Fast tape forward/rewind 69
C
FRANÇAIS
Manual tuning 60
Menu level 46
MIX 72
Mono 63
MUTE 45
ITALIANO
63
M
ENT 47
Entering CD names 72
EON 66
Equaliser 75, 76
EXIT 47
NEDERLANDS
Bandwidth adjustment
Blank Skip (BLS) 69
BND 46
LO/DX 62
Lost KeyCard 57
Loudness 50
SVENSKA
B
E
L
ESPAÑOL
Accessories 54
Adjusting the volume for traffic
announcements 66
Adjusts the display 78
Alternative frequency 59
Assistance in setting your equaliser 76
Automatic bandwidth adjustment 63
Automatic tuning 60
Display 46, 51
Display brightness daytime/night-time 78
Displaying the radio pass data 56
Dolby B NR 67
R
Radio Data System 59
Radio Monitor (RM) 69
Radio operation with RDS 59
Radio Scan 62
RDS-EON 66
PORTUGUÊS
A
DEUTSCH
Index
83
ChicHanKanMonParis gb 95%®
83
14.05.2002, 14:25 Uhr
Index
Regional programs 59
Remote control unit 53
Repeat (Cassette) 69
Repeat (Changer) 49
Repeating CDs 71
Repeating titles (Cassette) 69
Repeating tracks 71
S
S-CPS 68
SCAN 72
Scan time 62
Scanning cassette titles with SCAN 68
Scrolling through the broadcasting networks 60
Seek tuning sensitivity 62
Selecting CDs 70
Selecting the display mode (Cassette) 67
Selecting the display mode (Changer) 70
Selecting titles (Cassette) 68
Selecting tracks (Changer) 70
Setting recommendations on the
Internet 75
SHARX 63
Short Additional Memory (S.A.M.) 56
Softkeys 46
Station tuning 60
Stereo 63
Storing stations 61
Switching the sound on/off 45
Switching the unit on with the ignition
switched o 45
T
Technical Terminology 81
Telephone information 54
Telephone mute 54
Theft protection 56
Theft protection system 55
Time 74
TPM 71
Track reverse 68
Traffic information station reception 66
Traffic safety 54
Training the new KeyCard 57
Travelstore 61
Turn On Message (T.O.M.) 56
U
UPDATE
73
V
Visual theft protection 52
Volume 46
W
WAIT 1h 57
Warning beep 66
Waveband 60
84
ChicHanKanMonParis gb 95%®
84
14.05.2002, 14:25 Uhr
Service-Nummern / Service numbers / Numéros du service après-vente / Numeri del servizio di assistenza / Servicenummers / Telefonnummer för service / Números de servicio / Número de serviçco
Deutschland
Belgique
France
Nederland
Great Britain
Denmark
Sverige
Norway
Suomi
Österreich
Greece
âeská republika
USA
Singapore
Slovensko
Tel.:
Fax:
018 050 002 25
025 255 444
014 010 70 07
023 565 63 48
018 958 383 66
44 89 83 60
08 750 15 00
66 81 70 00
094 359 91
045 989 90 28
015 762 241
026 130 04 41
800-266 25 28
006 535 054 47
042 175 873 212
051 214 940 02
025 255 448
014 010 73 20
023 565 63 31
018 958 383 94
44 89 86 44
08 750 18 10
66 81 71 57
094 359 92 36
016 103 93 91
015 769 473
026 130 05 14
708-681 71 88
006 535 053 12
042 175 873 229
Blaupunkt-Werke GmbH
Bosch Gruppe
11/99
ChicHanKanMonParis d 95%®
K7/VKD 8 622 402 227
44
14.05.2002, 14:10 Uhr