Blaupunkt 7 649 026 110 Car Stereo System User Manual

663
OWNERS MANUAL
for
SATELLITE
COFFEE BREWER
with
ELECTRO-MECHANICAL
CONTROL
and
EXTERNALLY HEATED
SATELLITE SERVER
MODEL:
9102A
9104A
Includes:
Installation
Operation
Use & Care
Servicing Instructions
Model 9102A Satellite Brewer with 9105SS Satellite
PRINTED IN UNITED STATES OF AMERICA
p/n 76061 Rev. B ECN-12868
M663
050616 cps
WARRANTY STATEMENT
All electrical equipment manufactured by BLOOMFIELD
INDUSTRIES is warranted against defects in materials and
workmanship for a period of one year from the date of original
installation or eighteen (18) months from the date of shipment
from our factory, whichever comes first, and is for the benefit
of the original purchaser, except that:
a. airpots carry a 30 day parts warranty only.
b. dispensers; i.e., tea and coffee carry a 90 days parts
warranty only, excludes decanters.
THE FOREGOING OBLIGATION IS EXPRESSLY GIVEN IN
LIEU OF ANY OTHER WARRANTIES, EXPRESSED OR
IMPLIED, INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE, WHICH ARE HEREBY EXCLUDED.
BLOOMFIELD INDUSTRIES DIVISION / SPECIALTY
EQUIPMENT MANUFACTURING CORPORATION SHALL
NOT BE LIABLE FOR INDIRECT, INCIDENTAL OR
CONSEQUENTIAL DAMAGES OR LOSSES FROM ANY
CAUSE WHATSOEVER.
This warranty is void if it is determined that upon inspection by
an Authorized Service Agency that the equipment has been
modified, misused, misapplied, improperly installed, or
damaged in transit or by fire, flood or act of God.
It also does not apply if the serial nameplate has been
removed or unauthorized service personnel perform service.
The prices charged by Bloomfield Industries for its products
are based upon the limitations in this warranty. Seller’s
obligation under this warranty is limited to the repair of defects
without charge by a Bloomfield Industries Authorized Service
Agency or one of its sub-agencies. This service will be
provided on customer’s premises for non-portable models.
Portable models (a device with a cord and plug) must be
taken or shipped to the closest Authorized Service Agency,
transportation charges prepaid, for services.
In addition to restrictions contained in this warranty, specific
limitations are shown below (Additional Warranty Exclusions).
Bloomfield Industries Authorized Service Agencies are located
in principal cities.
This warranty is valid in the United States and void elsewhere.
Please consult your classified telephone directory or your food
service equipment dealer; or, for information and other details
concerning warranty, write to:
Service Parts Department
Bloomfield Industries
P.O. Box 280
Verdi, NV 89439
Phone: (888) 492-2782
Fax: (888) 492-2783
SERVICE POLICY AND PROCEDURE GUIDE
ADDITIONAL WARRANTY EXCLUSIONS
1.
2.
3.
5.
6.
7. Full use, care and maintenance instructions are supplied
with each machine. Those miscellaneous adjustments
noted are customer responsibility. Proper attention will
prolong the life of the machine.
8. Travel mileage is limited to sixty (60) miles from an
authorized Service Agency or one of its sub-agencies.
9. All labor shall be performed during normal working hours.
Overtime premium shall be charged to the customer.
10. All genuine Bloomfield replacement parts are warranted
for ninety (90) days from date of purchase on nonwarranted equipment.
Any use of non-genuine
Bloomfield parts completely voids any warranty.
11. Installation, labor and job check-out are not considered
warranty.
12. Charges incurred by delays, waiting time or operating
restrictions that hinder the service technicians ability
to perform services are not covered by warranty.
This includes institutional and correctional facilities.
SHIPPING DAMAGE CLAIMS PROCEDURE
NOTE: For your protection, please note that equipment in
this shipment was carefully inspected and packaged by
skilled personnel before leaving the factory.
Upon acceptance of this shipment, the transportation
company assumes full responsibility for its safe delivery.
IF SHIPMENT ARRIVES DAMAGED:
1. VISIBLE LOSS OR DAMAGE: Be certain that any
visible loss or damage is noted on the freight bill
or express receipt, and that the note of loss or damage
is signed by the delivery person.
2. FILE CLAIM FOR DAMAGE IMMEDIATELY:
Regardless of the extent of the damage.
3.
CONCEALED LOSS OR DAMAGE: if damage is
unnoticed until the merchandise is unpacked, notify the
transportation company or carrier immediately, and file
“CONCEALED DAMAGE” claim with them. This
must be done within fifteen (15) days from the date the
delivery was made to you. Be sure to retain the
container for inspection.
Bloomfield Industries cannot assume liability for damage or
loss incurred in transit. We will, however, at your request,
supply you with the necessary documents to support your
claim.
663 76061 Owners Manual for 9102A Single Satellite Brewer
4.
Resetting of safety thermostats, circuit breakers,
overload protectors, or fuse replacements unless
warranted conditions are the cause.
All problems due to operation at voltages other than
specified on equipment nameplates; conversion to
correct voltage must be the customer’s responsibility.
All problems due to electrical connections not made in
accordance with electrical code requirements and
wiring diagrams supplied with the equipment.
Replacement of items subject to normal wear, to include
such items as knobs and light bulbs. Normal maintenance
functions including adjustment of thermostats, microswitches,
and replacement of fuses and indicating lights are not
covered under warranty.
All problems due to inadequate water supply, such as
fluctuating, or high or low water pressure.
All problems due to mineral/calcium deposits, or
contamination from chlorides/chlorines. De-liming is
considered a preventative maintenance function and is
not covered by warranty.
TABLE OF CONTENTS
WARRANTY STATEMENT
SPECIFICATIONS
FEATURES & OPERATING CONTROLS
PRECAUTIONS & GENERAL INFORMATION
AGENCY APPROVAL INFORMATION
INSTALLATION
OPERATION
CLEANING INSTRUCTIONS
TROUBLESHOOTING SUGGESTIONS
SERVICING INSTRUCTIONS
EXPLODED VIEW, BREWER
EXPLODED VIEW, SATELLITE
SERVICE KITS
WIRING DIAGRAM
xi
1
2
4
4
5
7
9
11
12
18
21
22
23
Thank You for purchasing this
Bloomfield Industries appliance.
Proper installation, professional
operation and consistent
maintenance of this appliance will
ensure that it gives you the very
best performance and a long,
economical service life.
This manual contains the
information needed to properly
install this appliance, and to use,
care for and maintain or repair the
appliance in a manner which will
ensure its optimum performance.
SPECIFICATIONS
VOLTS
WATTS
AMPS
POWER
SUPPLY
9102A
120 VAC 1ø
1790
15
4' cord with
NEMA 5-15P
9104A
115/230 VAC 1ø
4325
20
Requires 4-wire
(L1, L2, Neut + Gnd)
not provided
663 76061 Owners Manual for 9102A Single Satellite Brewer
MODEL
1
FEATURES AND OPERATING CONTROLS
663 76061 Owners Manual for 9102A Single Satellite Brewer
Fig 1. SS-1 Satellite Brewing System
Features & Operating Controls
2
FEATURES AND OPERATING CONTROLS (continued)
Brewer
Adjustable Legs
Connector
Hot Water Faucet
Nameplate
Allows brewer to be leveled. Also allow clearance for cleaning
underneath brewer.
Connects to satellite. Allows satellite heater to be energized.
Allows brewer to sense that a satellite is in place.
Hot water dispensed here.
Lists manufacturer, model and serial number.
Also lists voltage and wattage rating of brewer.
Control Panel
Start Brew Switch
Press to start a brew.
Ready to Brew Indicator
Glows when water in tank is up to temperature.
Stop Brew Switch
Press to cancel a brew in progress.
Warmer Switch
Energizes satellite warmer.
Tank Heat Switch
Applies power to tank heater element. Glows when ON.
Volume Selector Switch
Allows selection of 1/2 gallon or 1 gallon brew (9102A); or,
1 gallon or 1-1/2 gallon brew (9104A).
Brew Chamber
Brew Chamber
Holds coffee grounds during brew cycle.
Wire Rack
Holds paper filter and coffee grounds in proper position in brew
chamber.
663 76061 Owners Manual for 9102A Single Satellite Brewer
Satellite
Brew-Thru Lid
Allows entry of brewed coffee and dilution water into satellite.
Minimizes splashing in the event satellite is tipped.
Handles
Allow the satellite to be safely carried.
Serving Faucet
Fresh coffee dispensed from satellite here.
Sight Glass
Check the level of coffee remaining here.
Drip Tray (optional)
Optional drip tray catches drips and spills from serving faucet.
Easily removed for cleaning.
3
GENERAL INFORMATION AND PRECAUTIONS
WARNING:
Electric
Shock hazard
All servicing requiring
access to non-insulated
electrical components
must be performed by a
factory authorized
technician.
DO NOT open any
access panel which
requires the use of tools.
Failure to follow this
warning can result in
severe electrical shock.
CAUTION:
Burn Hazard
Surfaces of the brewer
and brew chamber may
be hot to the touch and
can cause burns on
contact.
This appliance is intended for use in commercial establishments
only.
This appliance is intended to brew hot beverage, specifically coffee,
for human consumption. No other use is recommended or authorized
by the manufacturer or its agents.
Operators of this appliance must be familiar with the appliance use,
limitations and associated restrictions. Operating instructions must be
read and understood by all persons using or installing this appliance.
Cleanliness of this appliance is essential to good sanitation. Read and
follow all included cleaning instructions and schedules to ensure the
safety of the food product.
Surfaces of the brewer, brew chamber and satellite can be hot to the
touch, and may cause burns on contact.
Disconnect the brewer from electrical power before performing any
maintenance or servicing.
DO NOT submerge satellites in water.
DO NOT splash or pour water over, onto or into any controls,
control panel or wiring.
Any procedure which requires the use of tools must be performed by a
qualified technician.
This manual is considered to be a permanent part of the appliance.
This manual and all supplied instructions, diagrams, schematics, parts
breakdown illustrations, notices and labels must remain with the
appliance if it is sold or moved to another location.
This appliance is made in the USA. Unless otherwise noted, this
appliance has American sizes on all hardware.
This dual satellite brewing system is
E9253
listed under E9253.
This dual satellite brewing system meets NSF Standard 4 only when
installed and maintained per the instructions in this manual.
STD 4
4
663 76061 Owners Manual for 9102A Single Satellite Brewer
AGENCY APPROVAL INFORMATION
INSTALLATION INSTRUCTIONS
INSTALL LEGS
CAUTION:
The brewer is provided with adjustable legs. Be sure all four legs
are securely screwed into the base of the brewer.
Hazard from
Unstable Equipment
LEVEL THE UNIT
The adjustable legs allow the brewer to be leveled. Set the brewer
in its ultimate operating location and check for level with a spirit
level Adjust the brewer for level from front-to-rear, and from sideto-side. Be sure all four feet rest firmly on the counter.
PLUMBER’S INSTALLATION INSTRUCTIONS
IMPORTANT:
This equipment must be installed in accordance with the Basic
Plumbing Code of the Building Officials and Code Administrators
International (BOCA), and the Food Service Sanitation Manual of
the Food and Drug Administration (FDA). Also, this equipment
installation must comply with all local plumbing codes and
ordinances.
Rubber feet must be installed
on each leg of the brewer.
Legs must be adjusted so that
all four feet rest firmly on the
counter. Failure to properly
install the feet can result in
movement of the brewer, which
can cause personal injury and/
or damage to the brewer.
IMPORTANT:
Brewer must be installed on a water line with a full-flow pressure
between 20 psi and 90 psi.
NOTE: If water pressure varies greatly, or exceeds 90 psi at any
time, a water pressure regulator must be installed. Plumbing
installer must supply the regulator.
663 76061 Owners Manual for 9102A Single Satellite Brewer
Brewer must be connected to a potable water supply. Bloomfield
recommends not less than 1/4” copper tubing for installations of
12’ or less, and not less than 3/8” copper tubing for installations
exceeding 12’. Brewer must be connected to a COLD water line.
NOTE: DO NOT use a saddle tap for this water line connection.
A shut-off valve must be installed between the main water supply
and the brewer. Plumbing installer must supply the shut-off valve.
A 1/4-turn ball valve is recommended.
Brewer INLET FITTING is 1/4" Male Flare.
Fig. 3 Water Line Installation
Flush the water line before connecting to the brewer.
5
Fig. 2 Adjustable Legs
IMPORTANT:
In some areas, local codes
require a backflow preventer
(check valve) to be installed on
the inlet water line. If a backflow preventer is used, you
must install a water hammer
arrester in the incoming line,
between the backflow preventer
and the brewer inlet, as far
away from the brewer as space
will allow. This will relieve the
excessive back pressures that
can cause faucet leaks and
solenoid malfunctions.
NOTE:
While new-style brewers
incorporate an internal strainer
in the inlet solenoid, the
provided "Y" strainer should be
installed in the incoming water
line for ease of servicing.
INSTALLATION INSTRUCTIONS (continued)
CAUTION:
ELECTRICIAN’S INSTALLATION INSTRUCTIONS
Electric Shock
Hazard
Refer to Electrical Specifications, page 1.
Brewer must be properly
grounded to a reliable earth
ground to prevent possible
shock hazard. Do not assume a
plumbing line will provide such a
ground. Electrical shock may
cause serious injury.
Brewer requires a dedicated single-phase circuit:
Model 9102A 120 Volt AC, 50/60 Hz 1ø 20 Amps
NEMA 5-15R receptacle
Model 9104A
120/240 Volt AC, 50/60 Hz 1ø 30 Amps
3-Wire (L1, L2, Neutral) + Ground
Fig. 4 Model 9104A Terminal Block
IMPORTANT:
Initial set-up must be performed
by a qualified installer or
qualified service technician.
Improper set-up will damage the
brewer and void the warranty.
IMPORTANT:
Complete water line installation
before connecting brewer to
electrical power.
DO NOT turn the TANK
HEATER switch ON until the
water tank is filled. Heating
element must be completely
submerged in water at all times.
Damage to the brewer caused
by operating the heating
elements dry is NOT covered by
warranty.
Plumber’s and Electrician’s installation procedures must be
completed before proceeding with the set-up.
Be sure all electrical connections are secure, and that all
plumbing connections are secure and leak-proof.
1. CHECK BREWER FOR PROPER CONFIGURATION
Make sure spray disk gasket is in place INSIDE of spray
head.
Make sure spray disk is properly installed.
Check hot water faucet for proper operation.
2. FILL WATER TANK
Be sure POWER SWITCH and TANK HEATER switch are
OFF, then connect brewer to electric power.
Insert an empty brew chamber under the brew head. Place
an empty satellite in position. Pour fresh cold water into the
POUR-OVER OPENING until water flows from the brew
basket.
3. CHECK HEATING
Turn POWER SWITCH ON, then press TANK HEATER
switch ON. Water in tank will heat to brewing temperature in
approximately 30 minutes. When the water temperature
reaches the brew temperature setpoint, the READY-TOBREW light will glow.
Hold a suitable container under the HOT WATER FAUCET,
then open the faucet . Continue drawing water until all
trapped air is expelled.
6
663 76061 Owners Manual for 9102A Single Satellite Brewer
MAKE SURE THE FRONT
PANEL "TANK HEATER"
SWITCH IS IN THE OFF
POSITION BEFORE
CONNECTING BREWER TO
ELECTRICAL POWER.
INITIAL SET-UP INSTRUCTIONS
OPERATING INSTRUCTIONS
Fig. 5 Control Panel
BREWING COFFEE
Prepare the Brew Basket:
Make sure the wire rack is properly installed in the brew
chamber.
Insert one (1) Bloomfield paper filter into the brew chamber.
Make sure the filter is properly supported by the wire rack.
Add a measured amount of grounds to the brew basket.
Recommendations (may vary, depending on type of coffee
and personal taste preferences):
To brew 1/2 gallon, use 2.25 oz (64 gm) of coffee
To brew 1 gallon, use 4.50 oz (128 gm) of coffee
To brew 1-1/2 gallon, use 8.40 oz (240 gm) of coffee
Gently shake the basket to level the grounds.
IMPORTANT:
To avoid overflows, DO NOT
start the brew cycle unless an
EMPTY satellite is in place
under the brew chamber.
NOTE: The brew can be
cancelled at any time by
pressing the STOP switch.
Slide the brew chamber under the brew head.
Insert the Satellite:
Slide satellite under the brew chamber until it is fully seated.
Press WARMER switch ON.
663 76061 Owners Manual for 9102A Single Satellite Brewer
Fig. 6 Brew Basket
(9102A) Select Brew Volume:
NOTE: DO NOT change the
VOLUME SELECT switch
during a brew. This will disrupt
the brew cycle.
Press VOLUME SELECT switch to 1/2 GAL or 1 GAL
(9104A) Select Brew Volume:
Press VOLUME SELECT switch to 1 GAL or 1-1/2 GAL
Start the Brew:
Press the START BREW switch.
NOTE: The brew can be cancelled at any time by pressing
the STOP BREW switch.
At the end of the brew, be sure all water has stopped dripping
before removing the brew chamber.
When the READY-TO-BREW light comes on, the brewer is
ready to run another brew cycle.
Empty the Brew Basket:
Discard the grounds and the paper filter. Rinse the brew
chamber under clear water.
7
CAUTION:
Burn Hazard
Basket and contents are hot to
the touch and may cause burns
on contact.
OPERATING INSTRUCTIONS (continued)
Fig. 7 Water Flow Diagram
The BYPASS is an
adjustable flow control
valve. It is adjusted to
taste for 1 and 1-1/2
gallon brews in Model
9104A
NOTE: Use of the faucet
will not affect the volume
of water delivered for a
brew. However, overuse
of the faucet during a
brew may lower the
temperature of the brew
water.
BREW & BYPASS
This brewer is a standard displacement brewer with pour-over option.
For 9102A there is no bypass. Water admitted into the hot water tank
by the BREW SOLENOID will displace a like amount of heated water
through the brew head, brew chamber and into the satellite.
For 9104A, operation is identical to 9102A, except that a portion of the
heated water is diverted around the grounds in the brew chamber by a
BYPASS. Bypass water dilutes the brewed coffee, which, in the larger
volumes, would otherwise be too strong.
HOT WATER FAUCET
Water for the hot water faucet is heated in a coil inside of the water
tank. The faucet volume may be controlled by adjusting the FAUCET
NEEDLE VALVE. Hot water is delivered at inlet line pressure and is
approximately the same temperature as the brew water.
8
663 76061 Owners Manual for 9102A Single Satellite Brewer
The time the BREW
SOLENOID is open is
controlled by the TIMER
in response to the
position of the VOLUME
SELECTOR switch.
CLEANING INSTRUCTIONS
CLEANING INSTRUCTIONS
PROCEDURE: Clean Coffee Brewer
CAUTION:
Burn Hazard
PRECAUTIONS: Turn POWER SWITCH OFF.
Allow brewer to cool.
FREQUENCY:
Daily
TOOLS:
Mild Detergent, Clean Soft Cloth or Sponge
Bristle Brush
IMPORTANT:
1. Turn POWER SWITCH OFF.
Allow brewer to cool.
DO NOT use steel wool, sharp
objects, or caustic, abrasive or
chlorinated cleansers to clean
the brewer, brew baskets or
satellites.
2. Remove satellite.
3. Remove and empty brew chamber.
4. Remove spray disk and gasket from spray head
5. Wipe inside of spray head and area around spray head with a
soft clean cloth or sponge moistened with clean water.
6. Wash spray disk in a sink using warm water and a mild
detergent. A bristle brush may be used to clear clogged
spray holes. Rinse spray disks with clean water and allow to
air dry.
663 76061 Owners Manual for 9102A Single Satellite Brewer
Brewing and serving
temperatures of coffee are
extremely hot.
Hot coffee will cause
serious skin burns.
7. Wash brew basket in a sink using warm water and a mild
detergent. A bristle brush may be used to clean around the
wire racks and bypass channels. Rinse with clean water and
allow to air dry. Be sure wire rack is properly installed.
8. Remove and drain the drip tray. Rinse in a sink under warm
running water. Allow to air dry, then reinstall on brewer.
9. Wipe exterior of brewer and satellites with a soft clean cloth
or sponge moistened with clean water.
10. Reinstall gasket INSIDE brew head, then reinstall spray
disk.
11. Reinstall brew chamber.
12. Reinstall satellite.
Procedure is complete
9
DO NOT immerse or submerge
satellites in water.
CLEANING INSTRUCTIONS (continued)
CAUTION:
Burn Hazard
PROCEDURE: Clean Satellite
PRECAUTIONS: Drain Satellite before Cleaning
Brewing and serving
temperatures of coffee are
extremely hot.
Hot coffee will cause
serious skin burns.
FREQUENCY:
Twice Weekly
TOOLS:
Sight Glass Brush, Sanitizer
Soft Clean Cloth, Bucket
1. Remove and drain satellite.
IMPORTANT:
DO NOT use steel wool, sharp
objects, or caustic, abrasive or
chlorinated cleansers to clean
the satellites.
2. Place 1 packet of Sanitizer into 2-1/2 gallons of warm tap
water. Pour approximately 1 gallon of sanitizer solution into
each satellite. Allow to stand for 2 minutes.
3. Remove the shield cap (large vent) on top of the sight glass.
NOTE: It is not necessary to remove the sight glass unless it
is broken and replacement is required.
4. Run the sight glass brush up and down through the sight
glass at least 10 times.
5. Reinstall and tighten the shield cap.
6. Drain sanitizer solution from satellite into the bucket.
7. Disassemble faucet. Brush clean with sanitizer solution.
Reassemble faucet.
9. Rinse satellites: With an empty brew chamber in place, press
the BREW key and run 1 full cycle into satellite.
10. Drain water from satellites.
Procedure is complete
10
663 76061 Owners Manual for 9102A Single Satellite Brewer
8. Install satellite on brewer.
TROUBLESHOOTING SUGGESTIONS
SYMPTOM
POSSIBLE CAUSE
SUGGESTED REMEDY
Will not heat or brew
(no lights)
Brewer not plugged in or circuit
breaker tripped
Reconnect brewer to electric power
Reset circuit breaker
Main power switch off or
damaged
Check. Turn main power switch on.
Replace if needed
Brew switch damaged
Check. Replace if needed
Timer damaged
Check. Replace if needed
Will not brew
Volume selector switch damaged Check. Replace if needed
Brewer fails to heat
Brewer fails to stop
brewing after STOP
switch pressed
Coffee overflows from
brew chamber
Tank heat switch off
Turn tank heat switch on
Hi-limit tripped
Allow to cool, reset hi-limit
Thermostat out of adjustment or
damaged
Check. Adjust or replace as needed
Switch not pressed long enough
or firmly enough
Switch must be pressed firmly for at
least 1 second
Stop Brew switch damaged
Check. Replace if needed
Brew solenoid damaged or dirty
Check. Clean or replace as needed
Too much coffee or too fine a
grind
Use proper amount and grind of coffee
grounds per brew
663 76061 Owners Manual for 9102A Single Satellite Brewer
More than 1 filter paper or wrong Use 1 genuine Bloomfield filter paper
type of filter paper used
per brew
Insufficient brew volume
(all volumes)
Ready light does not glow
Poor spray pattern from
spray disk
Poor coffee quality
Timer out of adjustment or
damaged
Check time. Adjust or replace as
needed
Wire rack missing from brew
chamber
Check. Replace if needed
Low inlet water pressure
Other appliances on water line may be
robbing pressure. Brewer should be on
dedicated water line
Inlet or valve strainer plugged
Clean strainer
Timer out of adjustment
Adjust time
Timer damaged
Check. Replace if needed
Light damaged
Check. Replace if needed
Spray disk holes plugged
Check. Clean as needed
Gasket missing or improperly
installed
Reinstall gasket inside brew head
Keep brewer and satellites clean. Install a taste and odor filter in water
supply, and replace cartridges regularly.
Use a quality coffee with a consistent roast. Use proper grind and
amount of coffee per brew.
11
SERVICING INSTRUCTIONS
CAUTION:
SHOCK HAZARD
ACCESS PANELS
TOP PANEL is attached with two screws at the rear and a lip at
the front.
Disconnect brewer from electric
power before opening any
access panel.
TOP REAR PANEL is attached with four screws.
Note position of any wires or
hoses before removing them
from a panel.
TIMER ACCESS and HI-LIMIT ACCESS PLUGS may be pried
out with a thin flat blade screwdriver.
BASIN sets in the body. After disconnecting three hoses, it may
be lifted out.
FRONT PANEL is attached with four screws.
SATELLITE WARMER PANEL is held by two spring clips.
After removing the front panel, slide the warmer panel forward
approximately 1/2" to release.
SATELLITE BRACKET is attached with two screws
BOTTOM PANEL is attached with six screws.
LEGS screw into the bottom panel.
663 76061 Owners Manual for 9102A Single Satellite Brewer
Wrench for Faucet Tubing
12
SERVICING INSTRUCTIONS (continued)
CAUTION:
SHOCK HAZARD
TEMPERATURE ADJUSTMENT
PRECAUTIONS: Disconnect brewer from electric power.
Allow brewer to cool.
FREQUENCY:
As required to adjust delivered volume
TOOLS:
Phillips head screwdriver
1. Press HEATER ON/OFF switch to OFF. Turn POWER
switch on back of brewer OFF.
2. Remove TOP PANEL. Operating controls are accessible
through the top panel only.
3. Remove vent tube from the tank cover and insert a
thermometer of known accuracy.
4. Locate the CONTROL THERMOSTAT on the right side of the
top housing:
Turn CLOCKWISE to increase temperature
Turn COUNTER-CLOCKWISE to decrease temperature
1/8 turn is equal to approximately 10ºF change.
5. Turn POWER switch ON. Press TANK HEATER switch to
ON.
BOILING
POINT OF
WATER
TEMP. (ºF)
210
205
IDEAL
BREWING
TEMPERATURE
200
195
190
0
0 00 0
0
0
0
0
0
00 00 00 00 00
50 1,0 1,5 2,0 2,5 3,0 ,50 ,00 ,50 ,00 ,50 6,0 ,50
5
4
5
4
6
3
MAXIMUM
TEMPERATURE
SETTING
ELEVATION (feet above seal level)
BOILING
POINT OF
WATER
100
TEMP. (ºC)
663 76061 Owners Manual for 9102A Single Satellite Brewer
6. Allow the brewer to come up to brewing temperature. When
READY-TO -BREW light comes on, check temperature on
thermometer. Readjust thermostat as necessary.
97
IDEAL
BREWING
TEMPERATURE
RANGE
94
91
88
0
0
0 00 0
0
0
0
0
0
0
0
0
0
15 30 45 60 75 90 .05 .20 .35 .50 .65 1.8 .95
1
1
1
1
1
1
MAXIMUM
TEMPERATURE
SETTING
ELEVATION (meters above seal level)
7. When desired temperature is achieved, remove thermometer,
replace vent tube and reinstall top panel.
Procedure is complete
13
Live electrical circuits are
exposed during this procedure.
Use care to avoid uninsulated
electrical connectors.
Adjustments to be performed by
qualified technician only.
NOTE:
1/8 turn = approx 10ºF (5.5ºC)
SERVICING INSTRUCTIONS (continued)
Adjustments to be performed by
qualified technician only.
BREW TIMER ADJUSTMENT
PRECAUTIONS: None
NOTE:
Brewer is pre-adjusted to deliver
1/2, 1 and/or 1-1/2 gallons of
coffee at a water pressure of 50
p.s.i. Use this procedure to
adjust the delivered volume to
suit local conditions.
FREQUENCY:
As required to adjust delivered volume
TOOLS:
Small flathead screwdriver
Satellite or other container to calibrate volume
1. Press TANK HEATER switch to OFF.
2. Remove TIMER ACCESS COVER on front panel. Press
VOLUME SELECTOR to 1 GAL position.
3. Install an empty satellite and empty brew chamber.
Adjust only in small increments
to avoid large volume variations.
Recommend knob be turned no
more than one mark on the dial
plate at a time.
Moving the dial one mark will
change delivered volume by
approximately 6 oz.
4. Press START BREW switch. Brew should deliver 1 gallon
(128 fl. oz.). If adjustment is necessary, turn TIMER knob:
Turn CLOCKWISE to increase time;
Turn COUNTER-CLOCKWISE to decrease time.
Test after each adjustment. Be sure to empty satellite before
each test.
5. Turn TANK HEATER switch ON.
6. Allow the brewer to come up to brewing temperature, then
perform a test brew. Check delivered volume. Readjust as
necessary.
7. Reinstall TIMER ACCESS COVER.
14
663 76061 Owners Manual for 9102A Single Satellite Brewer
When desired volume is achieved, procedure is complete.
SERVICING INSTRUCTIONS (continued)
BYPASS ADJUSTMENT (9104A ONLY)
PRECAUTIONS: Disconnect brewer from electric power.
Allow brewer to cool.
FREQUENCY:
As required to adjust for change in delivered
volume, or to taste.
TOOLS:
Phillips head screwdriver
Stubby flathead screwdriver
Provided wire gauge set
1. Press TANK HEATER switch to OFF. Disconnect brewer
from electrical power.
2. Remove SATELLITE, BREW CHAMBER, TOP PANEL and
BASIN.
CAUTION:
SHOCK HAZARD
Disconnect brewer from electric
power before opening the top
panel.
The brewer is shipped from the
factory pre-set for 25% bypass.
This adjustment must never be
made unless the brewer is
installed on a soft water line, or
a change in coffee strength is
required.
3. Turn bypass adjustment screw several turns counterclockwise. Insert and hold appropriate gauge fully into
bypass valve from the outside of the brewer.
4. Turn bypass adjustment screw clockwise until the resistance
of the adjuster contacting the gauge is felt.
663 76061 Owners Manual for 9102A Single Satellite Brewer
5. Release the gauge set. Turn bypass adjustment screw
counterclockwise slowly until gauge set fall out of the valve.
6. Reassemble brewer and perform a 1 gallon brew and sample
for taste. Adjust from this point to achieve desired taste:
a. Repeat steps 1 and 2.
b. Turn bypass adjustment screw counterclockwise to
decrease coffee strength (increase dilution); or ,
clockwise to increase coffee strength (decrease dilution).
Bypass Gauge Set
7. Perform BREW TIMER ADJUSTMENT to insure delivery of
128 oz. in 1 gallon mode.
Procedure is complete
Bypass Adjustment
15
SERVICING INSTRUCTIONS (continued)
CAUTION:
CHEMICAL BURN
HAZARD
Deliming chemicals are caustic.
Wear appropriate protective
gloves and goggles during this
procedure.
Never siphon deliming
chemicals or solutions by
mouth.
This operation should only be
performed by qualified and experienced service personnel.
IMPORTANT: DO NOT spill,
splash or pour water or deliming
solution into or over any internal
component other than the inside
of the water tank.
IMPORTANT: DO NOT allow
any internal components to
come into contact with the
deliming solution. Take care to
keep all internal components
dry.
PRECAUTIONS: Disconnect brewer from electric power.
Allow brewer to cool.
FREQUENCY:
As required (Brewer slow to heat)
TOOLS:
Deliming Solution
Protective Gloves, Goggles & Apron
Mild Detergent, Clean Soft Cloth or Sponge
Bristle Brush, Bottle Brush
Large Sink (or other appropriate work area)
1.
Disconnect brewer from the electrical supply.
2.
Remove the brewer top panel, then remove the tank lid
assembly. Do not disconnect the tank assembly at this
time.
3.
Siphon all water from the hot water tank.
4.
Mix 2 gallons of deliming solution according to the
manufacturer’s directions. Carefully pour the deliming
solution into the water tank. Lower the lid assembly back
onto the tank. Allow to sit for 30 minutes, or as directed by
the chemical manufacturer.
5.
At end of soaking period, reconnect brewer to electrical
power. Install the brew chamber without filter paper or
grounds. Place an empty satellite under the brew
chamber. Force a 1-1/2 gallon brew:
a. Press the 1-1/2 gallon key
b. Press the brew key, then press and hold the brew key
until a brew is initiated.
Empty the satellite and repeat for the other side.
6.
Disconnect brewer from electrical power and allow to cool.
7.
Remove lid assembly from tank.
a. Using a stiff bristle brush, scrub internal components to
remove lime and calcium build-up.
b. Thoroughly rinse internal components of lid assembly
with clear water.
c. Store lid assembly in a safe location.
8.
Using a stiff bristle brush, scrub exposed portions of the
heating element and the inside surfaces of the tank to
remove lime and calcium build-up.
9.
Siphon all solution from the tank.
16
663 76061 Owners Manual for 9102A Single Satellite Brewer
NOTE: Repeat steps 4 and 7
as required to remove all buildup.
PROCEDURE: Delime the Water Tank
SERVICING INSTRUCTIONS (continued)
10.
Reinstall tank lid assembly into hot water tank. Make sure
the lid gasket is properly in place, then reinstall the holddown clamp.
11.
Remove spray disks and gaskets. Rinse both brew heads
with clean water. Using a stiff brush, scrub spray disk to
remove any lime or calcium build-up. Reinstall gaskets
and spray disks.
13.
Reconnect brewer to electrical supply .
14.
Install the brew chamber without filter paper or grounds.
15.
Place an empty satellite under the brew chamber. Run at
least five 1 gallon brew cycles and discard all water
generated at the end of each cycle.
Repeat for the other side.
16.
Rinse satellite with clean water. Reinstall empty satellite
under brew chamber.
663 76061 Owners Manual for 9102A Single Satellite Brewer
Brewer is ready to use.
17
NOTE: Normally, silicone
hoses do not need to be
delimed. Should deliming
hoses become necessary,
Bloomfield recommends
replacing the hoses.
EXPLODED VIEW
PLUMBING COMPONENTS
663 76061 Owners Manual for 9102A Single Satellite Brewer
18
663 76061 Owners Manual for 9102A Single Satellite Brewer
EXPLODED VIEW (continued)
ELECTRICAL COMPONENTS
19
EXPLODED VIEW ((continued)
CABINET & RELATED COMPONENTS
663 76061 Owners Manual for 9102A Single Satellite Brewer
20
663 76061 Owners Manual for 9102A Single Satellite Brewer
EXPLODED VIEW (continued)
SATELLITE ASSEMBLY 9105SS
21
SERVICE KITS
FAUCET REPAIR COMPONENTS
82680
Hex Lock Nut
8551-100B
7/16“ Lock Washer
82681
Washer
82556
Faucet Assembly
FAUCET REPAIR KITS
82573
82575
82576
82682
84804
84870
SOLENOID REPAIR KITS
85685
85218
85219
Handle
Seat Cup
Faucet Repair Kit (Includes Handle, Seat Cup, Spring,
Stem, Pin & Bonnet
Retainer Clip
Aerator Replacement Kit (Includes O-Ring,
Aerator Disk & Aerator Cap
Aerator Repair Kit (Includes O-Ring & Aerator Disk)
Solenoid, Complete, with Bypass
Inlet Fitting Kit (cap, inlet fitting, washer & strainer)
Inlet Strainer
663 76061 Owners Manual for 9102A Single Satellite Brewer
22
663 76061 Owners Manual for 9102A Single Satellite Brewer
WIRING DIAGRAMS
23
Bloomfield Industries, Inc.
Division of Carrier Commercial Refrigeration
In US and Canada
Telephone: 775-698-5700
Fax:
888-492-2783
Fax:
800-356-5142 (for orders only)
website: www.wellsbloomfield.com
PRINTED IN UNITED STATES OF AMERICA