Operating instructions | Blaupunkt San Remo CD31 Car Stereo System User Manual

Radio / CD
Konstanz CD31
San Remo CD31
Santa Cruz CD31
Operating instructions
14 13
SVENSKA
NEDERLANDS
3
4
5
12
11
6
10
7
ESPAÑOL
1
PORTUGUÊS
8
ITALIANO
FRANÇAIS
2
9
3
ENGLISH
DEUTSCH
5
6
7
=
>
ENGLISH
FRANÇAIS
ITALIANO
;
<
NEDERLANDS
4
9
:
AUDIO button to adjust the
bass, treble, balance and fader
settings.
Arrow buttons.
MENU button to open the basic
settings menus.
button to display the time.
Keys 1 - 5.
TRAF button to switch traffic information standby on/off.
PTY, to switch the PTY function
on/off.
Volume control.
, to increase the volume
, to decrease the volume
Button to switch the unit on/off.
To mute the unit’s volume.
SVENSKA
3
8
ESPAÑOL
2
button to release the control
panel.
FMT button (Konstanz CD31) to
select the FM memory levels,
to switch to radio mode,
to start the Travelstore function.
BAND button (San Remo CD31
and Santa Cruz CD31),
to select the FM memory levels
and MW / LW frequency range,
to switch to radio mode,
TS, to start the Travelstore function.
RDS button to switch the RDS
feature on/off.
To display scrolling text.
SCAN button to start the scan
function.
CD compartment.
X-BASS button for the X-Bass
function.
CD eject.
CD•C button to select CD, radio
and CD changer (if connected)
sources.
PORTUGUÊS
1
DEUTSCH
OPERATING ELEMENTS
25
CONTENTS
Notes and accessories .......... 27
CD mode ................................ 38
Road safety ................................... 27
Installation ..................................... 27
Accessories .................................. 27
Switching to CD mode .................. 38
Selecting tracks ............................ 38
Quick track selection ..................... 38
Fast searching (audible) ................ 38
Random play (MIX) ........................ 38
Scanning tracks (SCAN) ............... 38
Repeating tracks (REPEAT) ........... 39
Pausing playback (PAUSE) ............ 39
Changing the display ..................... 39
Removing the CD from the unit ...... 39
Removable control panel ....... 28
Switching on/off .................... 29
Adjusting the volume ............. 30
Setting the power-on volume ......... 30
Instantaneous volume reduction
(mute) ........................................... 30
Telephone audio / navigation audio .. 30
Confirmation beep ......................... 31
Radio mode ............................ 32
Switching to radio mode ................ 32
Changing the display ..................... 32
RDS functions (AF, REG) .............. 32
Selecting the frequency range /
memory ......................................... 33
Tuning into a station ....................... 33
Setting the sensitivity of the station
search mode ................................. 33
Storing stations ............................. 34
Storing stations automatically
(Travelstore) .................................. 34
Switching to preset stations ........... 34
Scanning receivable stations
(SCAN) ......................................... 34
Setting the scantime ...................... 35
Programme type (PTY) .................. 35
Treble reduction feature during
interference (HICUT) ..................... 36
Traffic information reception . 37
Switching traffic information
priority on/off ................................. 37
Setting the traffic announcement
volume .......................................... 37
26
CD changer mode .................. 40
Switching to CD changer mode ..... 40
Selecting a CD .............................. 40
Selecting tracks ............................ 40
Quick track selection ..................... 40
Fast searching (audible) ................ 40
Changing the display ..................... 40
Repeating individual tracks or
whole CDs (REPEAT) .................... 40
Random play (MIX) ........................ 41
Scanning all tracks on all CDs
(SCAN) ......................................... 41
Pausing playback (PAUSE) ............ 41
CLOCK - Time ........................ 42
Sound ..................................... 43
Adjusting the bass settings ............ 43
Adjusting the treble settings ........... 43
Volume distribution ................ 43
Adjusting the balance settings ....... 43
Adjusting the fader settings ........... 43
X-BASS .................................. 44
External audio sources .......... 44
Specifications ........................ 45
Guarantee .............................. 45
Installation instructions ........ 172
Accessories
Only use accessories approved by Blaupunkt.
CD changer
Road safety has absolute priority. Only operate your car radio if the
road and traffic conditions allow you
to do so. Familiarise yourself with the
unit before setting off on your journey.
You should always be able to hear
police, fire and ambulance sirens
from afar. For this reason, set the
volume of whatever you are listening to to a reasonable level.
You can connect the following Blaupunkt
CD changers:
CDC A 06, CDC A 08, CDC A 072 and
IDC A 09.
You can also connect the CDC A 05 and
CDC A 071 CD changers by using an
adapter cable (Blaupunkt no. 7 607 889
093).
SVENSKA
Road safety
FRANÇAIS
Amplifier
All Blaupunkt amplifiers can be used.
ITALIANO
The optional RC 08 or RC 10 remote
controls allow you to safely and conveniently access the most important functions of your car radio from your steering wheel.
ENGLISH
Remote control
NEDERLANDS
Thank you for deciding to purchase a
Blaupunkt product. We hope you enjoy
using this new piece of equipment.
Before using the device for the first time,
please read these instructions carefully.
The Blaupunkt editors are constantly
working on making the operating instructions clearer and easier to understand. However, if you still have any
questions on how to operate the unit
please contact your dealer or the telephone hotline for your country. You will
find the hotline telephone numbers printed at the back of this booklet.
DEUTSCH
NOTES AND ACCESSORIES
ESPAÑOL
Installation
PORTUGUÊS
If you want to install your car radio yourself, please read the installation and
connection instructions that follow these
operating instructions.
27
REMOVABLE CONTROL PANEL
button 1.
Removable control panel
➮ Press the
Theft protection
The control panel locking mechanism
opens.
As a way of protecting your car radio
against theft, the unit is equipped with
a removable control panel (release panel). Without this control panel, the car
radio is worthless to a thief.
Protect you car radio against theft by
taking the control panel with you every
time you leave your vehicle. Do not leave
the control panel in your vehicle - not
even in a hiding place.
The control panel has been designed
to be easy to use.
Note:
● Never drop the control panel.
● Never expose the control panel to
direct sunlight or other heat sources.
● Store the control panel in the supplied case.
● Avoid making direct skin contact
with the control panel’s contacts. If
necessary, clean the contacts with
a lint-free cloth soaked in cleaning
spirits.
Removing the control panel
1
28
➮ First, pull the control panel straight
●
●
●
off the unit and then out towards
the left.
The unit switches off after the control panel is removed.
All the current settings are saved.
Any CD already inserted in the unit
remains there.
Attaching the control panel
➮ Slide the control panel from left to
right into the unit’s panel locking
mechanism.
➮ Press the left-hand edge of the
control panel into the unit until it
clicks into place.
Note:
● When attaching the control panel,
make sure you do not press the
display.
If the unit was still switched on when
you removed the control panel, the unit
will automatically switch on with the last
settings activated (i.e. radio, CD, CD
changer, or AUX) when the panel is replaced.
➮ To do so, press button >.
➮ Gently insert the CD with the printed side uppermost into the drive
until you feel some resistance.
The CD will be drawn automatically into
the drive.
You must not hinder or assist the drive
as it draws in the CD.
The unit switches on. CD playback begins.
ENGLISH
Switching on/off using the vehicle
ignition
If the unit is correctly connected to the
vehicle’s ignition and it was not switched
off using button >, it will switch on/off
simultaneously with the ignition.
You can also switch the unit on even if
the ignition is off:
FRANÇAIS
There are various ways of switching the
unit on/off:
Switching on by inserting a CD
If the unit is switched off and there is no
CD inserted in the drive,
ITALIANO
Switching on/off
DEUTSCH
SWITCHING ON/OFF
Note:
To protect the vehicle battery, the
unit will switch off automatically after one hour if the ignition is off.
NEDERLANDS
●
Switching on/off using the
removable control panel
➮ Remove the control panel.
SVENSKA
The unit switches off.
➮ Attach the control panel again.
ESPAÑOL
The unit switches on. The last settings
(radio, CD, CD changer or AUX) will be
reactivated.
Switching on/off using button >
➮ To switch the unit on, press button
PORTUGUÊS
>.
➮ To switch the unit off, press button
> for longer than two seconds.
The unit switches off.
29
ADJUSTING THE VOLUME
Adjusting the volume
The system volume can be adjusted in
steps from 0 (off) to 66 (maximum).
To increase the system volume,
➮ press the
button =.
To decrease the system volume,
➮ press the
button =.
Setting the power-on volume
You can set the default volume at which
the unit switches on.
➮ Press the MENU button :.
➮ Keep pressing the or button
9 until “ON VOL” appears in the
display.
➮ Set the power-on volume using the
and buttons 9.
To help you adjust the volume more
easily, the volume will be increased /
decreased as you make your changes.
If you change the setting to “0”, the power-on volume will be the same as the
volume level that was set before the unit
was last switched off.
Note:
To protect your hearing, the poweron volume is limited to a value of
“38”. If the volume level was higher
when the unit was switched off, the
volume will be reset to “38” when
the unit is switched on again.
When you have finished making your
changes,
●
➮ press the MENU button : twice.
30
Instantaneous volume reduction
(mute)
This feature allows you to instantaneously reduce (mute) the volume to a level preset by you.
➮ Briefly press button >.
“MUTE” appears in the display.
Setting the mute level
You can set the unit’s mute volume level.
➮ Press the MENU button :.
➮ Keep pressing the or button
9 until “MUTE LVL” appears in the
display.
➮ Set the mute level using the
and
buttons 9.
When you have finished making your
changes,
➮ press the MENU button : twice.
Telephone audio / navigation
audio
If your car radio is connected to a mobile telephone or a navigation system,
the unit’s volume will be muted as soon
as you “pick up” the telephone or as
soon as a navigation announcement is
made. The caller or voice output will then
be heard over the car radio loudspeakers. In order for this to work, the mobile
telephone or navigation system must be
connected to the car radio in the manner described in the installation instructions.
You can find out from your Blaupunkt
dealer which navigation systems can be
used with your car radio.
➮ Press the MENU button :.
➮ Keep pressing the or button
9 until “BEEP” appears in the display.
and buttons 9 to
switch between the options.
“OFF” means beep off, “ON” means the
beep is switched on.
ENGLISH
FRANÇAIS
For some functions you will hear a confirmation beep if you keep a button
pressed for longer than two seconds.
For instance, after storing a radio station to a station button you will hear a
confirmation beep. The beep can be
switched on/off.
➮ Use the
➮ Press the MENU button :.
ITALIANO
➮ Press the MENU button :.
➮ Keep pressing the or button
Confirmation beep
NEDERLANDS
If a traffic information message is received during a telephone call or whilst
a navigation announcement is being
made, the traffic message will only be
played after the call or voice output is
finished.
If you are already listening to a traffic
announcement and a telephone call
arrives or the navigation system wishes to make a voice output, the traffic
announcement will first be heard. Once
the traffic message is finished, you can
listen to the call or the voice output.
You can set the volume level at which
telephone calls and the navigation voice
output will first be heard.
DEUTSCH
ADJUSTING THE VOLUME
9 until “TEL VOL” appears in the
display.
➮ Set the required volume using the
SVENSKA
and buttons 9.
When you have finished making your
changes,
➮ press the MENU button : twice.
ESPAÑOL
Note:
Using the volume control =, you
can directly adjust the volume of
telephone calls and navigation
voice output (whilst they are being
heard).
PORTUGUÊS
●
31
RADIO MODE
Radio mode
This unit is equipped with an RDS radio
receiver. Many of the receivable FM stations transmit a signal that not only carries the programme but also additional
information such as the station name
and programme type (PTY).
The station name appears in the display as soon as it is received.
Switching to radio mode
If you are in CD, CD changer or AUX
mode,
➮ press the FMT or BAND (TS) button 2.
Or
➮ keep pressing the CD•C button 7
until “RADIO” appears in the display.
Changing the display
To briefly display the time,
➮ keep the MENU ( ) button :
pressed until the time appears in
the display.
RDS functions (AF, REG)
The RDS functions AF (Alternative Frequency) and REG (Regional) extend
your radio’s range of functions.
● AF: If this RDS function is activated, the unit automatically tunes into
the best receivable frequency for
the station that is currently set.
● REG: At certain times, some radio
stations divide their programme
into regional programmes providing
different regional content. You can
32
use the REG function to prevent
the car radio from switching to alternative frequencies that are
transmitting different programme
content.
Note:
● REG must be separately activated/
deactivated in the menu.
Switching REG on/off
➮ Press the MENU button :.
➮ Keep pressing the or button
9 until “REG” appears in the display.
“OFF” or “ON” is displayed alongside
“REG”.
To switch REG on/off,
➮ press the or button 9.
➮ Press the MENU button :.
Switching the RDS function on/off
To use the RDS functions (AF and
REG),
➮ press the RDS button 3.
The RDS functions are active when
“RDS” lights up in the display. When the
RDS functions are switched on, “REG
ON” or “REG OFF” appears briefly in
the display.
Selecting the memory level
To switch between the FM memory levels and the MW and LW frequency ranges,
➮ keep pressing the FMT or BAND
(TS) button 2 until the required
frequency range / memory level is
displayed.
Tuning into a station
There are various ways of tuning into a
station.
Automatic seek tuning
➮ Press the
or
button 9.
The unit tunes into the next receivable
station.
9 until “SENS” appears in the display.
➮ Press the
button 9.
The display shows the currently set value for sensitivity. “SENS HI6” means that
the tuner is highly sensitive. “SENS LO1”
means it is set to the lowest sensitivity
setting.
If “SENS LO” is selected, “lo” lights up
in the display.
➮ Set the required sensitivity using
the
and
buttons 9.
➮ Press the MENU button :.
Tuning into stations manually
You can also tune into stations manually.
Note:
● You can only tune into stations
manually if the RDS function is deactivated.
➮ Press the
or
button 9.
Browsing through broadcasting
networks (only FM)
If a radio station provides several programmes, you have the option of browsing through its so-called “broadcasting
network”.
33
ENGLISH
FRANÇAIS
➮ Press the MENU button :.
➮ Keep pressing the or button
ITALIANO
Note:
● The MW and LW frequency ranges
are not available on the Konstanz
CD31.
There are three preset memory levels
for the FM range and one for each of
the MW and LW ranges. Five stations
can be stored on each memory level.
NEDERLANDS
You can configure the radio to only tune
into stations with a strong reception or
to also tune into those with a weak reception.
SVENSKA
This unit can receive programmes
broadcast over the FM, MW and LW frequency ranges.
ESPAÑOL
Setting the sensitivity of the
station search mode
PORTUGUÊS
Selecting the frequency range /
memory
DEUTSCH
RADIO MODE
RADIO MODE
Note:
● If you want to use this feature, the
RDS function must be activated.
or button 9 to
switch to the next station on the
broadcasting network.
When using this feature, you will only
be able to switch to stations that you
have received once already. To do so,
use either the Travelstore function or
allow the automatic seek tuning feature
to run once through the entire frequency range.
➮ Press the
Storing stations
Storing stations manually
➮ Select the required FM1 / FM2 /
FMT memory or MW / LW frequency range (MW and LW are not
available on the Konstanz CD31).
➮ Tune into the station.
➮ Press one of the station buttons 1 5 ; for longer than one second to
store the station to that button.
Storing stations automatically
(Travelstore)
You can automatically store the five stations with the strongest reception in the
region (only for FM). The stations are
stored in the FMT memory.
Note:
● Stations that were previously
stored in this memory are deleted
in the process.
➮ Keep the FMT or BAND (TS) button 2 pressed for longer than two
seconds.
34
The station storing procedure begins.
“T-STORE” appears in the display. After
the process is completed, the station
stored in FMT memory location 1 will
be played.
Switching to preset stations
➮ Select the memory level on which
the station was stored.
➮ Press the preset station button of
the station you want to listen to.
Scanning receivable stations
(SCAN)
You can briefly play all the receivable
stations. You can set the scanning time
to between 5 and 30 seconds in the
menu.
Starting SCAN
➮ Press the SCAN button 4.
Scanning begins. “SCAN” appears briefly in the display followed by the current
frequency (which flashes).
Stopping SCAN and continuing
listening to a station
➮ Press the SCAN button 4 again.
Scanning is stopped and the station that
was tuned into last will remain active.
Programme type (PTY)
Besides transmitting the station name,
some FM stations also provide information on the type of programme that they
are broadcasting.
For example, the programme types can
be:
CULTURE
TRAVEL
JAZZ
SPORT
NEWS POP
ROCK
MUSIC
Using the PTY function, you can directly select stations of a particular programme type.
PTY-EON
If you specify the programme type and
start seek tuning, the radio will switch
from the current station to a station of
the selected programme type.
Switching PTY on/off
➮ Keep the TRAF (PTY) button <
pressed until “PTY” appears in or
disappears from the display.
The programme type appears briefly in
the display when you switch PTY on.
Selecting a programme type and
starting seek tuning
➮ Press the
or
button 9.
The current programme type appears
in the display.
ENGLISH
FRANÇAIS
Note:
The set scantime also applies to
scanning in CD and CD changer
mode.
●
ITALIANO
➮ press the MENU button : twice.
NEDERLANDS
the and buttons 9.
When you have finished making your
changes,
SVENSKA
➮ Set the required scantime using
ESPAÑOL
9 until “SCANTIME” appears in
the display.
Note:
If no station is found that corresponds to the selected programme
type, you will hear a beep and “NO
PTY” appears briefly in the display.
The station that was listened to last
will then be tuned into again.
● If the tuned radio station or another
station on the broadcasting network broadcasts the required programme type at a later point in
time, the radio automatically
switches from the currently tuned
station or from CD mode / CD
changer mode to the station whose
programme type matches the one
you selected.
●
➮ If you want to select another programme type, you can do so by
pressing the or button 9
whilst in this display.
PORTUGUÊS
Setting the scantime
➮ Press the MENU button :.
➮ Keep pressing the or button
DEUTSCH
RADIO MODE
Or
➮ Press one of the buttons 1 - 5 ; to
select a programme type that is
stored on one of these buttons.
35
RADIO MODE
The selected programme type is displayed briefly.
Treble reduction feature during
interference (HICUT)
or button 9 to start
seek tuning.
The next station corresponding to your
selected programme type will then be
tuned into.
The hicut function improves reception
during poor radio reception. If interference occurs, the treble is automatically
reduced.
Storing a programme type on a
station button
➮ Press the MENU button :.
➮ Keep pressing the or button
➮ Press the
➮ Select a programme type using the
or
button 9.
➮ Press and hold the required button
Switching hicut on/off
9 until “HICUT” appears in the
display.
1 - 5 ; until you hear a beep.
The programme type is now stored on
the station button 1 - 5 ; that you selected.
or button 9 to
switch HICUT on/off.
“HICUT 0” means that treble will not be
reduced, and “HICUT 1” means that treble will be reduced.
Selecting the PTY language
➮ Press the MENU button :.
You set the language in which the programme type is displayed.
➮ Press the MENU button :.
➮ Keep pressing the or button
9 until “PTY LANG” appears in
the display.
or button 9 to
switch between German, English
and French.
When the required language appears
in the display,
➮ Press the
➮ press the MENU button : twice.
36
➮ Press the
TRAFFIC INFORMATION RECEPTION
ing the
and
DEUTSCH
ENGLISH
buttons 9.
ITALIANO
FRANÇAIS
➮ Press the MENU button :.
NEDERLANDS
Note:
You will hear a warning sound
● if you leave the reception area of a
traffic information station that you
are currently listening to.
● if, while listening to a CD, you leave
the reception area of a traffic information station that you are tuned
into and the subsequent automatic
search cannot find a new traffic information station.
● if you retune the radio from a traffic
information station to a station that
does not broadcast traffic information.
If you hear the warning sound, you can
either switch off traffic information priority or tune into a station that broadcasts traffic information.
➮ Set the announcement volume us-
SVENSKA
Traffic announcement priority is active
when a traffic jam symbol lights up in
the display.
9 until “TA VOLUME” appears in
the display.
ESPAÑOL
Switching traffic information
priority on/off
➮ Press the TRAF button <.
Setting the traffic
announcement volume
➮ Press the MENU button :.
➮ Keep pressing the or button
PORTUGUÊS
Traffic information
reception
37
CD MODE
CD mode
You can use this unit to play standard
CDs with a diameter of 12 cm.
Risk of damage to the CD drive!
CD singles with a diameter of 8 cm
and contoured CDs (shape CDs) are
not suitable for playback in this unit.
We accept no liability for any damage to the CD drive that may occur
as a result of the use of unsuitable
CDs.
Switching to CD mode
●
If there is no CD inserted in the
drive.
➮ Gently insert the CD with the printed side uppermost into the CD
compartment until you feel some
resistance.
The CD will be drawn automatically into
the drive.
Do not use force when inserting the CD.
You must not hinder or assist the drive
as it draws in the CD.
CD playback begins.
● If a CD is already inserted in the
drive.
➮ Keep pressing the CD•C button 7
until “CD” appears in the display.
Playback begins from the point at which
it was last interrupted.
Selecting tracks
➮ Press one of the
/ or / buttons 9 to select the next or previous track.
38
If you press the / button 9 once,
the current track will be played again
from the beginning.
Quick track selection
To quickly select tracks backwards or
forwards,
or buttons 9
pressed until fast-reverse / fast-forward track selection begins.
➮ keep one of the
Fast searching (audible)
To fast search backwards or forwards,
buttons 9
pressed until fast reversing / fast
forwarding begins.
➮ keep one of the
Random play (MIX)
➮ Press button 4 (MIX) ;.
MIX appears in the display. The next
randomly selected track will then be
played.
Stopping MIX
➮ Press button 4 (MIX) ; again.
MIX disappears from the display.
Scanning tracks (SCAN)
You can briefly play all the tracks on a
CD.
➮ Press the SCAN button 4.
Note:
● You can set the scantime. For further details, read the section entitled “Setting the scantime” in the
“Radio mode” chapter.
➮ press the SCAN button 4 again.
The current track will then continue to
be played.
Repeating tracks (REPEAT)
button 9.
The current setting is displayed. “TIME”
for the playing time display and “PLAY”
for the track number display.
button 9 to select the
required setting.
➮ Press the
➮ Press the MENU button : twice.
If you want to repeat a track,
Removing the CD from the unit
➮ press button 3 (RPT) ;.
To remove the CD from the unit,
RPT appears in the display. The track is
repeated until you deactivate RPT.
➮ keep the CD•C button 7 pressed
until the CD is ejected.
ITALIANO
Cancelling the repeat function
ENGLISH
To stop scanning,
➮ Press the
FRANÇAIS
Stopping SCAN and continuing
playback
DEUTSCH
CD MODE
If you want to cancel the repeat function,
NEDERLANDS
➮ press button 3 (RPT) ; again.
RPT disappears. Normal playback is
then continued.
SVENSKA
Pausing playback (PAUSE)
➮ Press button 2 ( ) ;.
“PAUSE” appears in the display.
Cancelling pause
ESPAÑOL
➮ Press button 2 ( ) ; while in
pause mode.
Playback is continued.
PORTUGUÊS
Changing the display
To switch between the track number display and the track number / playing time
display,
➮ Press the MENU button :.
➮ Keep pressing the or button
9 until “CD DISP” appears in the
display.
39
CD CHANGER MODE
CD changer mode
Fast searching (audible)
Note:
● Information on handling CDs, inserting CDs and operating the CD
changer can be found in the operating instructions supplied with
your CD changer.
To fast search backwards or forwards,
Switching to CD changer mode
➮ Keep pressing the CD•C button 7
buttons 9
pressed until fast reversing / fast
forwarding begins.
➮ keep one of the
Changing the display
To switch between the track number /
CD number display and the track
number / playing time display,
until “CHANGER” appears in the
display.
Playback begins with the first CD that
the CD changer detects.
➮ press the MENU button :.
➮ Keep pressing the or button
Selecting a CD
➮ Press the
To move up or down to another CD,
The current setting is displayed. “TIME”
for the playing time display and “CD NO”
for the CD number display.
➮ press the
or
several times.
button 9 once or
To move up or down to another track on
the current CD,
or
several times.
button 9 once or
Quick track selection
To quickly select tracks backwards or
forwards,
or buttons 9
pressed until fast-forward / fast-reverse track selection begins.
➮ keep one of the
button 9.
button 9 to select the
required setting.
➮ Press the
Selecting tracks
➮ press the
9 until “CDC DISP” appears in the
display.
➮ Press the MENU button : twice.
Repeating individual tracks or
whole CDs (REPEAT)
To repeat the current track,
➮ briefly press button 3 (RPT) ;.
“RPT TRCK” appears briefly and RPT
lights up in the display.
To repeat the current CD,
➮ press button 3 (RPT) ; again.
“RPT DISC” appears briefly and RPT
lights up in the display.
40
Stopping SCAN
To stop scanning,
➮ keep pressing button 3 (RPT) ;
again.
The current track will then continue to
be played.
➮ briefly press button 4 (MIX) ;.
“MIX CD” appears briefly and MIX lights
up in the display.
To play the tracks on all inserted CDs in
random order,
Note:
You can set the scantime. For further details, read the section entitled “Setting the scantime” in the
“Radio mode” chapter.
●
Pausing playback (PAUSE)
➮ Press button 2 ( ) ;.
“PAUSE” appears in the display.
➮ press button 4 (MIX) ; again.
Cancelling pause
“MIX ALL” appears briefly and MIX lights
up in the display.
➮ Press button 2 ( ) ; while in
Stopping MIX
FRANÇAIS
To play the tracks on the current CD in
random order,
ITALIANO
Random play (MIX)
NEDERLANDS
until “RPT OFF” appears in the display and RPT disappears.
➮ briefly press the SCAN button 4
ENGLISH
Cancelling the repeat function
To stop the current track or current CD
from being repeated,
DEUTSCH
CD CHANGER MODE
pause mode.
Playback is continued.
SVENSKA
To stop the tracks from being played in
random order,
➮ keep pressing button 4 (MIX) ;
ESPAÑOL
until “ MIX OFF” appears in the display and MIX disappears.
Scanning all tracks on all CDs
(SCAN)
PORTUGUÊS
To scan all the tracks on all inserted CDs
in ascending order,
➮ press the SCAN button 4.
“SCAN” appears in the display.
41
CLOCK - TIME
To display the time,
or button 9 to
switch between the modes.
When you have finished making your
changes,
➮ Keep the MENU ( ) button :
➮ press the MENU button :.
➮ Press the
CLOCK - Time
Displaying the time
pressed until the time appears in
the display.
Setting the time
➮ Press the MENU button :.
➮ Keep pressing the or button
9 until “CLOCKSET” appears in
the display.
➮ Press the
button 9.
The time appears in the display. The
minutes flash on and off and can be
adjusted.
➮ Adjust the minutes using the
/
buttons 9.
Once the minutes are set,
➮ press the
button 9.
The hours flash on and off.
➮ Adjust the hours using the
/
buttons 9.
When you have finished making your
changes,
➮ press the MENU button : twice.
Selecting 12/24-hour clock
mode
➮ Press the MENU button :.
“MENU” appears in the display.
➮ Keep pressing the
or button
9 until “24 H MODE” or “12 H
MODE” appears in the display.
42
Displaying the time when the
unit is off and the ignition is on
To display the time when the unit is off
and the ignition is on,
➮ press the MENU button :.
“MENU” appears in the display.
➮ Keep pressing the
or button
9 until “CLOCK OFF” or “CLOCK
ON” appears in the display.
or button 9 to
switch between the displays.
When you have finished making your
changes,
➮ Press the
➮ press the MENU button :.
Briefly displaying the time when
the unit is switched off
To briefly display the time when the unit
is off,
➮ press the MENU ( ) button :.
The time is displayed for around 8 seconds.
Adjusting the bass settings
Adjusting the balance settings
To adjust the BASS,
To adjust the left/right volume distribution (balance),
To adjust the TREBLE,
➮ press the AUDIO button 8.
“BASS” appears in the display.
or button 9
until “TREB” appears in the display.
➮ Keep pressing the
or
just the treble.
or button 9
until “BAL” appears in the display.
➮ Keep pressing the
Adjusting the treble settings
➮ Press the
“BASS” appears in the display.
button 9 to ad-
or button 9 to adjust the balance (right/left).
➮ Press the
Adjusting the fader settings
To adjust the front/back volume distribution (fader),
➮ press the AUDIO button 8.
“BASS” appears in the display.
or button 9
until “FADER” appears in the display.
➮ Keep pressing the
or button 9 to adjust the fader (front/back).
➮ Press the
ITALIANO
button 9 to ad-
ESPAÑOL
or
just the bass.
PORTUGUÊS
➮ Press the
➮ press the AUDIO button 8.
NEDERLANDS
➮ press the AUDIO button 8.
“BASS” appears in the display.
ENGLISH
Volume distribution
FRANÇAIS
Sound
DEUTSCH
VOLUME DISTRIBUTION
SVENSKA
SOUND
43
X-BASS
EXTERNAL AUDIO SOURCES
X-BASS
External audio sources
The X-BASS feature can be used to
boost the bass at low volume levels.
Instead of connecting a CD changer,
you can also connect another audio
source equipped with a line output. The
audio source, for example, can be a
portable CD player, MiniDisc player or
MP3 player.
If you want to connect an external audio source you will need a Blaupunkt
adapter cable (Blaupunkt no.: 7 607 897
093).
The AUX input must be activated in the
menu.
Adjusting the X-BASS boost
settings
The X-BASS boost can be set in steps
ranging from 1 to 3.
“X-BASS OFF” means that the X-BASS
feature is switched off.
➮ Press the X-BASS button 6.
➮ Keep pressing the
or
button 9 until the required setting appears in the display.
If the X-BASS boost is set to a value of
1, 2 or 3, the X-BASS symbol appears
in the display.
When you have finished making your
changes,
➮ press the X-BASS button 6.
Switching the AUX input on/off
➮ Press the MENU button :.
➮ Keep pressing the or button
9 until “AUX OFF” or “AUX ON”
appears in the display.
or button 9 to
switch AUX on/off.
➮ Press the
➮ Press the MENU button :.
Note:
The AUX input can now be selected by
pressing the CD•C button 7.
44
Output power:
4 x 25 watts sine
in accordance
with DIN 45 324
at 14.4 V
4 x 45 watts max.
power
Tuner
Frequency ranges:
FM:
87.5 – 108 MHz
MW:
531 – 1,602 kHz
LW:
153 – 279 kHz
FM frequency response:
35 - 16,000 Hz
CD
Frequency response:
20 - 20,000 Hz
Pre-amp out
4 channels:
3V
ENGLISH
The scope of the guarantee is orientated around the regulations in force within the country in which the unit was purchased.
If your unit develops a fault, please contact your dealer and present the purchase receipt.
If the statutory guarantee period in your
country is less than 12 months, Blaupunkt will grant a 12-month manufacturer’s guarantee. This guarantee does
not cover damage due to wear, incorrect usage or commercial use.
If you wish to enforce a claim under the
manufacturer’s guarantee that is provided by Blaupunkt, please send the faulty
unit together with the purchase receipt
to the Blaupunkt customer service centre in your country. You can find out
which address is closest to you by contacting the telephone hotline listed on
the back page of this booklet. Blaupunkt
retains the right to rectify defects or supply a replacement.
FRANÇAIS
Amplifier
ITALIANO
Guarantee
NEDERLANDS
Specifications
DEUTSCH
GUARANTEE
SVENSKA
SPECIFICATIONS
Input sensitivity
ESPAÑOL
2 V / 6 kOhm
10 V / 1 kOhm
PORTUGUÊS
AUX input:
Tel./Nav. input:
Subject to changes!
45
Download PDF

advertising