Specifications | BlueAnt Wireless T8 Bluetooth Headset User Manual

Introduction
MFB (Multi Function Button)
2.
Volume Up Button
3.
MFB
1.
Before you can use your headset, you must ‘link’ it with the device you wish to use.
See the support section of www.blueantwireless.com for troubleshooting and
Frequently Asked Questions (FAQ) as well as info on using with computers for
VOIP application\s.
Phone/Device Software
Please make sure you have the latest firmware upgrade for your Phone especially
if you are using a PDA Phone. Go to the support section of the manufacturers’
website to check you have the latest version. Many new mobile phones, pda’s and
computers phones require a Bluetooth patch to improve Bluetooth functionality
from the original released version.
Resetting Your Phone/Device
Phones can become prone to software and memory issues which may cause
Bluetooth reconnection problems. This can be fixed simply by turning the phone off
and back on again. The phone will be reset and the working memory cleared.
1. First turn the T8 ON, then Press and Hold the MFB
button for about 3
seconds. At this point the T8 is in Standby mode i.e. not connected to any device.
2. To put your headset go into Pairing mode, Press and Hold the Volume UP
button for about 2 seconds. The blinking blue and red indicators will alternate.
MFB (Multi Function Button)
Step B: Pairing you headset to your phone/device
Volume Down Button
2.
Trouble Shooting and Support Documents
Step A: Put your headset in Pairing Mode
Headset Call Controls
1.
Pairing with your Bluetooth device
Volume Up Button
3.
Volume Down Button
Note: Before use please
read the Additional
Information sections
in this users guide.
1.
2.
3.
4.
5.
Turn on the Bluetooth function of your phone or device.
Perform a “Bluetooth device discovery” from your phone or device.
Select ‘T8 micro” from the list of discovered devices
Enter the Pincode/Passkey “0000”.
Select the T8 micro from the list of paired devices and press Connect.
Note: Some devices will not require this last step
Step C: Initial Test
Charging your Headset
Getting started… charging of your T8 will take about 2 hours.
Follow the procedure as follows:
1. Insert the T8 Wall Charger into a DC power source and switch ON.
2. Insert the plug on the end of the T8 charging cable into your headset
as shown below.
Your headset and your phone should now be paired and connected, ready to
make and receive calls. Depending on your device, you may see that a headset
symbol has appeared on you screen. To confirm they are successfully paired
and operating properly please try the following.
1. On your phones keypad, dial a contact you wish to call.
2. Press Send on your phone to initiate the call.
The call will be heard on the headset.
Pairing to up to 8 devices
1. Make sure the last device used has Bluetooth switched off or is out of range.
2. Follow the procedure in ‘Pairing your Bluetooth device’ above
Connecting to other devices
1. Make sure the last used device has Bluetooth switched off or is out of range.
2. Go to your phones Bluetooth Menu, Select the T8 micro and Press Connect
3. The Red LED indicators will light up showing that the T8 is
being charged.
The Red LED indicator
turns on
The Red LED indicator
is off
4. When charging is complete the Red LED indicators will turn off.
5. Remove the charger plug from the T8 then switch off the charger.
Note: The rechargeable battery in the T8 will take several complete
charges till it reaches its optimum storage capacity.
After charging the first time, use the T8 as normal until a ‘low battery’ is
indicated. Charge again and repeat…!!!
LED indicator chart
Power on
Blue indicator blinks twice
Power off
Red indicator blinks twice
Standby mode
Blue indicator blinks once every 4 seconds
Sniff mode
Blue indicator rapidly blinks twice every 4 seconds
Pairing mode
Red & Blue indicators alternately blink
Incoming call
Purple indicator blinks once per second
Active call
Blue indicator rapidly blinks 3 times every 4 seconds
Low battery
All Blue indicators will change to Red
Charging
Red indicator is continuously ON steady on
Charging complete
Red indicator turns OFF
Reset
Purple indicator blinks twice
Note: Sniff mode means your headset has a connection with your phone
but is conserving power, and will wake up when any function is activated.
Specifications
Bluetooth Version…............. v2.0
Supported Bluetooth
Profiles ................................ Headset and Handsfree
Number of devices .............. Stores information for 8 different devices
Frequency Band .................. 2.4GHz ~ 2.4835 (frequency Hopping
Certification Approvals ........ CE, FCC, BQB, C-Tick
Security ............................... 128 bit Digital Encryption
Talk Time ............................. 9 Hours
Standby Time ...................... 250 Hours
Battery................................. Rechargeable 120mAh Li-Polymer
Charger ............................... 110v – 240v Switch Mode Charger
Operating range .................. Up to 10 meters
Contact Us
Weight ................................. 13 grams
For Connection Assistance or if you are having difficulties
using your T8 micro, please make an enquiry on our website
Indicator Lights.................... Blue, Red and Purple
(LED’s can be turned off)
Dimensions ......................... 52 x 26 x 28 mm
www.blueantwireless.com
Compatibility ....................... Windows, Mac, Mobile Phones,
Pda’s and VOIP applications
or call
Nth America
support@myblueant.com
1 866 891-3032
New Zealand
support@blueant.com.au
0800 443 122 (NZ)
Australia
support@blueant.com.au
1300 669 049 (AUS)
Disclaimers
Headset Functions
BlueAnt Warranty Process
1. Power ON your headset: Press and Hold the MFB
for about 3 seconds until
the blue indicator flashes twice. After powering on, your headset will automatically
connect to your last used phone if it is in operating range. If no paired phone is in
range or no phone has been paired, the T8 will enter Standby mode.
2. Power OFF your headset: Press and Hold the MFB
for about 3 seconds
until the red indicator flashes twice.
3. To enter Pairing mode: While in Standby mode, Press and Hold the Volume
button for about 2 seconds
Up
once when there is an incoming
4. To Answer or End a call: Press the MFB
once again to end the call.
call to Answer. Press the MFB
for about 2 seconds when
5. To Reject* a call: Press and Hold the MFB
there is an incoming call.
for
6. To Redial* the last call: Press and Hold the Volume Down Button
about 2 seconds.
7. To activate Voice Dialing*: while connected to your phone, Press the MFB
once. Voice commands must have been previously recorded into your phone
(see your phones user guide)
8. To adjust the Volume: Click the Volume Up
or Volume Down Button
during a call. Adjust to the desired level. The volume level you set to will be
remembered by the T8 and used on the next call.
/
9. To Disable/Enable the LED indicators: Double Press the Volume Up
when your headset is in standby mode.
Down Button
10. To Reset your headset to factory settings: Press and keep Holding one
after the other the Volume Up Button
, MFB then Volume Down Buttons
.
When you click the third button the T8 micro will blink purple twice and then
switch itself off. You must be in Standby mode to reset the T8 micro i.e. while
not connected to any device.
1. Should you be having difficulties in the operation of your T8 micro please refer
to the online FAQ and support documents..
2. Check our website for more information, updated manuals and troubleshooting.
* To use these functions, your phone/device must support the Bluetooth Handsfree
Profile. Headset profile will not activate these features of the T8 micro.
www.blueantwireless.com
3. Call us and speak to one of the BlueAnt Wireless Customer Service Team
We will clarify whether you have a hardware or connection issue.
4. Return the unit directly to BlueAnt for testing and replacement of faulty items
– Please call to arrange a Return Merchandise Authorization (RMA) number.
Warranty Terms and Conditions
1. BlueAnt Warrant the original purchaser of this product only.
2. BlueAnt will replace or repair any faulty product provided it has not been
misused or abused in any way.
3. There are no user serviceable parts inside this product. Using a nonauthorized repairer will void the warranty.
4. The T8 micro Warranty is valid for 2 years (24 months) from the date
of purchase.
• Proof of purchase must be supplied to obtain warranty.
• Headset must be in original packaging with serial number for warranty to be valid.
5. Warranties are effective from the proof of purchase date and not from the date
of any subsequent repair or replacement.
This manual is published by BlueAnt. The information contained in this document is
subject to change without notice. All rights reserved.
The Bluetooth word, mark and logos are owned by the Bluetooth SIG, Inc. and any
use of such marks by BlueAnt is under license. Other trademarks and trade names
are those of their respective owners.
Federal Communications Commission (FCC) statement
15.21 You are cautioned that changes or modifications not expressly approved by the
part responsible for compliance could void the users authority to operate the equipment.
15.105(b) This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
> Reorient or relocate the receiving antenna.
> Increase the separation between the equipment and receiver.
> Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help. You are cautioned
that changes or modifications not expressly approved by the party responsible for
compliance could void your authority to operate the equipment.
FCC RF radiation exposure statement:
This Transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
Warning: Prolonged use of a headset at high volumes may affect your hearing
capacity. Using for extensive time periods may result in noise induced hearing loss
(NIHL). Be careful about using in noisy environments as the tendency is to turn
the headset up to compensate. Hearing loss may occur if the headset is used at
maximum volumes for more than 5 minutes per day. Hearing loss may occur if the
headset is used at medium volumes if used for more than 1 hour per day. Exposure
to sound at such a close range for more than eight hours a day may result in hearing
loss, even at low levels.
Download PDF

advertising