Bolens 114-620A Lawn Mower User Manual

Bolens 114-620A Lawn Mower User Manual
INSTRUCTION MANUAL
LEG PRESS (V2)
OPTION OF K1 (V2)
QUESTION?
As a quality home gym supplier we are committed to your complete satisfaction. If you have questions, or
find missing or damaged parts, we will guarantee your complete satisfaction through our authorized
dealer service centers or our home office customer service department. Please call your local dealer for
assistance or RSI at 800-990-5556 (9:00 AM - 5:00 PM). Our trained techanicians will provide immediate
assistance to you, free of charge.
We stand behind our products. Every piece, every part of this BODYCRAFT strength training system is
guranteed for as long as you own it. We will repair or replace anything that goes wrong.
4109LP
Bodycraft is a division of Recreation Supply Inc.
P. O. Box 181
Sunbury, OH 43074
STEP 3
Eyelet end
LEG PRESS CABLE (243)
Metal ball end
Pull out the selector pin at weight stack of K1 gym to allow top cable movable.
1. Attach the eyelet end of the Leg Press Cable (243) to the Leg Extension Arm (17),
using one 3/8" X 3" Hex Bolt (113) and one 3/8" Nylon Nut (138) as shown in Fig.1.
2. Run the cable through the slot in the front of the Seat Frame (7) and mount a
pulley in the slot using one 3/8" X 2-3/4" Hex Bolt (114), two 3/8" steel Bushing
(83), two 3/8" Washers (130) and one 3/8" Nylon Nut (138) as shown in Fig 2.
3. Slide the cable through the Base Frame (1) from front to rear slot, you will now
mount a pulley (65) in the rear slot, using 3/8" X 2-1/2" Hex Bolt (116) and one 3/8"
Nylon Nut (138). Then route the cable under a pulley mounted on the plate welded
on the rear Base Frame (1), attach Pulley Guard (28) and Metal Tab (27) at both
side of the pulley, using one 3/8" X 2" Hex Bolt (117) and one 3/8" Nylon Nut (138).
4. Route the cable up and around pulley mounted in the second hole in the bottom of
the Double Pulley Block (24), using one 3/8" X 1-3/4" Hex Bolt (118) and one 3/8"
Nylon Nut (138). When cabling is complete, this pulley can be moved upward to
take a slack or downward to gain length.
5. Continue to route the cable down to the pulley on the Base Frame (1), mount a
pulley using one 3/8" X 1-3/4" Hex Bolt (118) and one 3/8" Nylon Nut (138) as
shown in Fig.6.
6. Continue to route the cable underneath the weight stack and around the
horizontally mounted pulley on the Leg Press Main Frame (202), mount the pulley
using one 3/8" X 1-3/4" Hex Bolt (233) and one 3/8" Nylon Nut (241) as shown in
Fig. 7.
7. Continue to route the cable through the slot in the Leg Press Main Frame (202),
and under and around (exiting on the top) the lowest pulley on the Rear Leg Press
Support (208) as shown in Fig. 8,10. Mount the pulley using one 3/8" X 1-3/4" Hex
Bolt (233) and one 3/8" Nylon Nut (241).
8. Then route the cable under and around (exiting on the top) the right side (as if
sitting on seat) pulley mounted in the leg Press Main Frame (202) as shown in
Fig.9,11. Mount two pulleys here using one 3/8" X 2-3/4" Hex Bolt (232) and one
3/8" Nylon Nut (241).
9. Route the cable in the same manner under and around the uppermost pulley
mounted on the Rear Leg Press Support (208) as shown in Step 1. Mount the
pulley using one 3/8" X 1-3/4" Hex Bolt (233) and one 3/8" Nylon Nut (241).
10. Route the cable in the same manner under and around the left side (as if sitting
on seat) pulley mounted in the Leg Press Main Frame (202) as shown in Step 2.
11. Hold the ball end of the cable with Metal Washer (246) in front of the inner tube of
the receptor holder (244). Tighten the receptor Holder (244) on the Rear Leg
Press Support (208) as shown in Fig.12, using one 3/8" X 2-1/4" Hex Bolt (249),
two 3/8" Washers (238) and one 3/8" Nylon Nut (241).
-6-
STEP 3
LEG PRESS CABLE (243)
Eyelet end
FIG 1
113
17
65
7
130
83
130
138
FIG 5
24
118
1
FIG 7
FIG 6
65
T9
138
65
28
138
FIG 8,10
233
FIG 10
241
221
202
1
65
FIG 4
221
138
138
119
116
65
138
117
27
FIG 3
FIG 2
114
130
83
Metal ball end
241
118
FIG 8
233
208
STEP 1
FIG 9,11
FIG 9
232
241
221
FIG 12
STEP 2
FIG 5
FIG12
FIG 1
FIG 9 FIG 2
FIG10
FIG 4
FIG 12
248
247
249
238
245 246
241
FIG 8
FIG11
FIG 7
FIG 6
238 244
-7-
FIG 3
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement