Owner`s manual | Bosch Appliances 44 Oven User Manual

T5505_7505UF(EN).QX33
04.4.12
10:01 AM
Page 1
OWNER’S
MANUAL
COLOR TV/VCR
SRC2213W (13 inch)
SRC2419 (19 inch)
13” MODEL ILLUSTRATED
This Owner’s Manual is made of
recycled paper.
As an ENERGY STAR ®
Partner, our company has
determined that this product meets
the ENERGY STAR ® guidelines for
energy efficiency. ENERGY STAR ®
is a U.S. registered mark.
INSTRUCCIONES EN ESPAÑOL INCLUIDAS.
If you need additional assistance for set-up or operating
after reading owner’s manual, please call
TOLL FREE : 1-800-968-3429
Please read before using this equipment
T5505_7505UF(EN).QX33
04.4.12
10:01 AM
Page 2
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE
TO RAIN OR MOISTURE.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A
RISK OF ELECTRIC SHOCK IS PRESENT
WITHIN THIS UNIT.
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
THIS SYMBOL INDICATES THAT THERE
ARE IMPORTANT OPERATING AND
MAINTENANCE INSTRUCTIONS IN THE
LITERATURE ACCOMPANYING THE
APPLIANCE.
CAUTION
The caution marking is located on the rear of the cabinet.
IMPORTANT SAFEGUARDS
1.Read instructions-All the safety and operating instructions
should be read before the appliance is operated.
POUR
AMEUBLES- Cet appareil ne doit être SYMBOLELESD'AVERTISSEMENT
COMPOSANTES
APPAREIL ET MEUBLE A ROULETTES
placé que sur un meuble (avec ou sans
roulettes) recommandé par le fabricant.
Si vous l’installez sur un meuble à
roulettes, déplacez les deux ensembles
S3126A
avec précaution. Un arrêt brusque, l’utilisation d’une force excessive et des surfaces irrégulières
risquent de déstabiliser l’ensemble et de le renverser.
2.Retain Instructions-The safety and operating instructions
should be retained for future reference.
3.Heed Warnings-All warnings on the appliance and in the
operating instructions should be adhered to.
4.Follow Instructions-All operating and use instructions
should be followed.
9. Ventilation-Slots and openings in the cabinet and the back
or bottom are provided for ventilation and to ensure reliable
operation of the TV/VCR and to protect it from overheating, and these openings must not be blocked or covered.
The openings should never be blocked by placing the
TV/VCR on a bed, sofa, rug, or other similar surface. This
TV/VCR should never be placed near or over a radiator or
heat register. This TV/VCR should not be placed in a builtin installation such as a bookcase or rack unless proper
ventilation is provided or the manufacturer’s instructions
have been adhered to.
5.Cleaning-Unplug TV/VCR from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol cleaners. Use
a damp cloth for cleaning.
EXCEPTION: A product that is meant for uninterrupted
service and, that for some specific reason, such as the possibility of the loss of an authorization code for a CATV converter, is not intended to be unplugged by the user for cleaning or any other purpose, may exclude the reference to
unplugging the appliance in the cleaning description otherwise required in item 5.
6.Attachments-Do not use attachments not recommended by
the TV/VCR manufacturer as they may cause hazards.
10.Power Sources-This TV/VCR should be operated only
from the type of power source indicated on the marking
label. If you are not sure of the type of power supply to
your home, consult your appliance dealer or local power
company. For TV/VCRs intended to operate from battery
power, or other sources, refer to the operating instructions.
7.Water and Moisture-Do not use this TV/VCR near waterfor example, near a bath tub, wash bowl, kitchen sink, or
laundry tub, in a wet basement, or near a swimming pool,
and the like.
8.Accessories-Do not place this TV/VCR on an unstable cart,
stand, tripod, bracket, or table. The TV/VCR may fall, causing serious injury to someone, and serious damage to the
appliance. Use only with a cart, stand, tripod, bracket, or
table recommended by the manufacturer, or sold with the
TV/VCR. Any mounting of the
PORTABLE CART WARNING
appliance should follow the manufacturer’s instructions and should
use a mounting accessory recommended by the manufacturer. An
appliance and cart combination
should be moved with care.
Quick stops, excessive force, and
S3126A
uneven surfaces may cause the
appliance and cart combination to
overturn.
11.Grounding or Polarization-This TV/VCR is equipped
with a polarized alternating-current line plug(a plug having
one blade wider than the other). This plug will fit into the
power outlet only one way. This is a safety feature. If you
are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your
electrician to replace your obsolete outlet. Do not defeat the
safety purpose of the polarized plug.
12.Power-Cord Protection-Power-supply cords should be
routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles,
and the point where they exit from the appliance.
-2-
EN
9I03
T5505_7505UF(EN).QX33
04.4.12
10:01 AM
Page 3
F IGURE A
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECT RICAL CODE
ANTE NNA
L EAD I N
WI RE
GROUND
CLAMP
A NTENNA
DI SCHARG E UN I T
(NEC SECTION 8 10 -2 0)
EL ECT RI C
SE RV I CE
EQ U I PM EN T
G RO UNDI NG CO NDUCT ORS
(NEC SECTION 8 10 -2 1)
G RO UND CL AM PS
NEC - NATI O NAL EL ECTRI CAL CO DE
POWER SERVI C E G RO UNDI NG
EL EC TR O DE SYST EM
(NEC ART 2 50 , PART H)
S2 8 9 8 A
13.Outdoor Antenna grounding-If an outside antenna or
cable system is connected to the TV/VCR, be sure the
antenna or cable system is grounded so as to provide some
protection against voltage surges and built-up static
charges. Article 810 of the National Electrical Code,
ANSI/NFPA No. 70, provides information with respect to
proper grounding of the mast and supporting structure,
grounding of the lead-in wire to an antenna discharge unit,
size of grounding conductors, location of antenna-discharge
unit, connection to grounding electrodes, and requirements
for the grounding electrode. (Fig. A)
14.Lightning-For added protection for this TV/VCR receiver
during a lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the wall
outlet and disconnect the antenna or cable system. This will
prevent damage to the TV/VCR due to lightning and
power-line surges.
15.Power Lines-An outside antenna system should not be
located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into
such power lines or circuits. When installing an outside
antenna system, extreme care should be taken to keep from
touching such power lines or circuits as contact with them
might be fatal.
16.Overloading-Do not overload wall outlets and extension
cords as this can result in a risk of fire or electric shock.
17.Object and Liquid Entry-Never push objects of any kind
into this TV/VCR through openings as they may touch dangerous voltage points or short out parts that could result in
a fire or electric shock. Never spill liquid of any kind on
the TV/VCR.
19.Damage Requiring Service-Unplug this TV/VCR from
the wall outlet and refer servicing to qualified service personnel under the following conditions:
a. When the power-supply cord or plug is damaged or frayed.
b. If liquid has been spilled, or objects have fallen into the
TV/VCR.
c. If the TV/VCR has been exposed to rain or water.
d. If the TV/VCR does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions, as improper adjustment of other controls may result in damage and will often
require extensive work by a qualified technician to restore
the TV/VCR to its normal operation.
e. If the TV/VCR has been dropped or damaged in any way.
f. When the TV/VCR exhibits a distinct change in performance-this indicates a need for service.
20.Replacement Parts-When replacement parts are required,
be sure the service technician has used replacement parts
specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may
result in fire, electric shock, injury to persons or other hazards.
21.Safety Check-Upon completion of any service or repairs to
this TV/VCR, ask the service technician to perform routine
safety checks to determine that the TV/VCR is in proper
operating condition.
22.Heat-This TV/VCR product should be situated away from
heat sources such as radiators, heat registers, stoves, or
other products (including amplifiers) that produce heat.
18.Servicing-Do not attempt to service this TV/VCR yourself
as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY
INSERT.
ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE
LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
-3-
EN
9I03
T5505_7505UF(EN).QX33
04.4.12
10:01 AM
Page 4
PRECAUTIONS
LOCATION
For safe operation and satisfactory performance of
your TV/VCR, keep the following in mind when
selecting a place for its installation:
• Shield it from direct sunlight and keep it away
from sources of intense heat.
• Avoid dusty or humid places.
• Avoid places with insufficient ventilation for proper
heat dissipation. Do not block the ventilation holes
at the top and bottom of the unit. Do not place the
unit on a carpet because this will block the ventilation holes.
• Install unit in a horizontal position.
• Avoid locations subject to strong vibration.
• Do not place the TV/VCR near strong magnetic fields.
• Avoid moving TV/VCR to locations where temperature differences are extreme.
AVOID THE HAZARDS OF
ELECTRICAL SHOCK AND FIRE
• Do not handle the power cord with wet hands.
• Do not pull on the power cord when disconnecting
it from an AC wall outlet. Grasp it by the plug.
• If, by accident, water is spilled on your unit, unplug
•
•
the power cord immediately and take the unit to an
Authorized Service Center for servicing.
Do not put your fingers or objects into the
TV/VCR cassette holder.
Do not place anything directly on top of the unit.
WARNING
Moisture condensation may occur inside the unit
when it is moved from a cold place to a warm place,
or after heating a cold room or under conditions of
high humidity. If a tape is played in a TV/VCR
which has moisture, it may damage the tape and
TV/VCR. Therefore if condensation occurs inside the
unit, turn the POWER button on and allow at least 2
hours for the unit to dry out.
IMPORTANT COPYRIGHT INFORMATION
Unauthorized recording or use of broadcast television programming, video tape, film or other copyrighted material may violate applicable copyright
laws. We assume no responsibility for the unauthorized duplication, use, or other acts which infringe
upon the rights of copyright owners.
FCC WARNING- This equipment may generate or use radio frequency energy. Changes or
modifications to this equipment may cause
harmful interference unless the modifications
are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change
or modification is made.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and
used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
1) Reorient or relocate the receiving antenna.
2) Increase the separation between the equipment
and receiver.
3) Connect the equipment to an outlet on a circuit
different from that to which the receiver is connected.
4) Consult the dealer or an experienced radio/TV
technician for help.
The serial number of this product may be found on the back of the unit. No other TV/VCR has the same serial
number as yours. You should record the number and other vital information here and retain this book as a permanent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.
Date of Purchase
Dealer name
Dealer Address
Dealer Phone No.
Model No.
Serial No.
-4-
EN
9I03
T5505_7505UF(EN).QX33
04.4.12
10:01 AM
Page 5
TABLE OF CONTENTS
C IMPORTANT SAFEGUARDS . . . . . . . . . . . . .2
C PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . .4
C FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
C SUPPLIED ACCESSORIES . . . . . . . . . . . . . . .6
C OPERATING CONTROLS AND FUNCTIONS 7
C PREPARATION FOR USE . . . . . . . . . . . . . . . .9
ANTENNA/CABLE CONNECTIONS . . . . . . .9
FRONT A/V INPUT . . . . . . . . . . . . . . . . . . . .10
INSTALLING THE BATTERIES . . . . . . . . . . .10
C SET UP FOR USE . . . . . . . . . . . . . . . . . . . . .10
SELECTING THE LANGUAGE . . . . . . . . . . .10
CLOCK SET UP (AUTO / MANUAL) . . . . . .10
DAYLIGHT-SAVING TIME . . . . . . . . . . . . . .12
CHANNEL SET UP . . . . . . . . . . . . . . . . . . . .13
DELETING (OR ADDING) CHANNEL . . . . .13
C TV OPERATION . . . . . . . . . . . . . . . . . . . . . . .14
WATCHING A TV PROGRAM . . . . . . . . . . . .14
GAME MODE . . . . . . . . . . . . . . . . . . . . . . . . .14
DEGAUSSING . . . . . . . . . . . . . . . . . . . . . . . .14
PICTURE CONTROL . . . . . . . . . . . . . . . . . . .14
CLOSED CAPTION SYSTEM . . . . . . . . . . . .15
V-CHIP SET UP . . . . . . . . . . . . . . . . . . . . . . . .15
FM MODE (13 inch model only) . . . . . . . . . . .17
C PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . .17
NORMAL PLAYBACK . . . . . . . . . . . . . . . . . .18
AUTO REPEAT PLAYBACK . . . . . . . . . . . . .18
SEARCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
SLOW MOTION . . . . . . . . . . . . . . . . . . . . . . .19
RENTAL PLAYBACK . . . . . . . . . . . . . . . . . . .19
VERTICAL HOLD CONTROL . . . . . . . . . . . .20
STILL PICTURE . . . . . . . . . . . . . . . . . . . . . . .20
TRACKING ADJUSTMENT . . . . . . . . . . . . . .20
C RECORDING . . . . . . . . . . . . . . . . . . . . . . . . .20
NORMAL RECORDING . . . . . . . . . . . . . . . . .20
OTR (One Touch Recording) . . . . . . . . . . . . . .21
TIMER RECORDING . . . . . . . . . . . . . . . . . . .21
TIMER PROGRAM EXTENSION . . . . . . . . .22
HINTS FOR AUTOMATIC TIMER
RECORDING . . . . . . . . . . . . . . . . . . . . . . . . .23
AUTO RETURN . . . . . . . . . . . . . . . . . . . . . . .23
WAKE UP TIMER . . . . . . . . . . . . . . . . . . . . . .23
SLEEP TIMER . . . . . . . . . . . . . . . . . . . . . . . . .24
C COPYING A VIDEO TAPE . . . . . . . . . . . . . . .24
C ON SCREEN DISPLAY . . . . . . . . . . . . . . . . .25
C SPECIAL FEATURES . . . . . . . . . . . . . . . . . .25
REAL TIME TAPE COUNTER . . . . . . . . . . . .25
AUTO REWIND-EJECT . . . . . . . . . . . . . . . . .25
C MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . .25
C TROUBLESHOOTING GUIDE . . . . . . . . . . .26
C SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . .27
C CABLE CHANNEL DESIGNATIONS . . . . . .27
C WARRANTY . . . . . . . . . . . . . . . . . . .Back Cover
INDICE
CONTROLES DE OPERACIÓN Y
SUS FUNCIONES . . . . . . . . . . . . . . . . . . . . . . . .28
CONEXIONES DE ANTENA/CABLE . . . . . . . .30
SELECCION DE IDIOMA . . . . . . . . . . . . . . . . .30
AJUSTE DE CANAL . . . . . . . . . . . . . . . . . . . . . .31
AJUSTE DEL RELOJ . . . . . . . . . . . . . . . . . . . . .31
MODO DE ENTRADA EXTERNA . . . . . . . . . . .30
A NOTE ABOUT RECYCLING
This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in
accordance with your local recycling regulations.
Batteries should never be thrown away or incinerated but disposed of in accordance with your local regulations concerning chemical wastes.
-5-
EN
9I03
T5505_7505UF(EN).QX33
04.4.12
10:01 AM
Page 6
FEATURES
• Rotary 4-head Record/Playback System–Four
•
•
heads ensure excellent picture quality and special
effects playback.
Index Search–Fast-forwards to start of next recording.
Slow Motion–View recorded program at slower
than normal speed.
• Infrared remote control
• Trilingual on screen menu display selectable in
•
•
•
•
heads as you insert or remove a cassette.
• Zero Return–The tape returns to counter of
0:00:00 by rewinding or fast forwarding.
• Still–“Freeze” the picture at any time, for close
•
English, Spanish, or French
Real time counter–This shows the elapsed record-
•
ing or playback time in hours, minutes, and seconds. The “–” indication will appear when the tape
is rewound further than the tape counter position
“0:00:00”.
•
• 181 channel capability PLL frequency synthesiz•
• Auto Head Cleaner–Automatically cleans video
er tuner with direct station call–(A converter may
be necessary to view scrambled cable channels.)
Auto Clock Setting–Allows you to set the clock
from a PBS broadcast station.
Closed caption system–You may view specially
labeled (cc) TV programs, movies, news, prerecorded tapes, etc. with either a dialogue caption or
text display added to the program.
Game mode–Automatically selects front A/V input
mode and allows the TV/VCR display to be suitable for use with TV games.
Auto power on and off system–Automatically
turns on the TV/VCR when you insert the cassette,
turns off after auto-rewind, and ejects when the
beginning of the tape is reached.
• Auto rewind when the end of a tape is
•
•
• 1 Year, 8 events (including Daily and Weekly
•
•
reached–This function doesn’t occur when using
•
timer recording.
• 2 Step picture search operation–You can view a
•
video program at a high speed or super high speed
in either a forward or reverse direction in LP and
SLP mode. For SP mode only high speed.
• Three different playback tape speeds : SP/LP/SLP
• Two different recording tape speeds : SP/SLP
viewing of a particular scene. Only tapes recorded
in SLP mode will show a fairly clear picture.
Digital Auto Tracking (DTR)–Automatically
adjusts the tracking for each tape you play.
Rental play mode–Improves playback picture
quality from worn tapes, such as rental tapes.
Auto repeat–Allows you to repeat the playing of a
tape indefinitely without pressing the PLAY button.
Time search–Lets you set the TV/VCR to advance
the tape by entering the desired playback time you
want to skip.
OTR (One Touch Recording)–Instant recording in
30 to 480 minutes increments is possible at the
push of the REC/OTR button.
•
Timer Recording)–The built-in timer allows you to
record up to 8 programs at different times on different channels up to 1 year in advance. The Daily
timer allows recordings to be made of daily broadcasts, and the Weekly timer allows recording to be
made once a week up to the end of the tape.
Auto return–After timer recording is finished, the
TV/VCR can return to the beginning of the recording.
Wake-up/Sleep timer–Allows you to have the
TV/VCR automatically turn on or off at a desired
time.
Timer Program Extension–Allow you to shift the
time schedule for automatic timer recording.
V-CHIP–Enables parents to prevent their children
from watching inappropriate material on TV.
FM mode–Allows you to listen to the FM radio.
(13 inch model /SRC2213W only)
SUPPLIED ACCESSORIES
Remote Control Unit
2 AA Batteries
PART NO.
(NE109UD for SRC2213W)
(NE138UD for SRC2419)
Rod Antenna
(13” model only supplied)
PART NO. (0EMN00673 or
0EMN01599 or 0EMN01755)
• If you need to replace these accessories, please refer to the PART NO. under the illustrations and call 1-800968-3429.
• Depending on your antenna system, you may need different types of Combiners (Mixer) or Separators
(Splitter). Contact your local electronics store for these items.
• We do not recommend the use of universal remote controls. Not all of the functions may be controlled with
a universal remote control. If you decide to use a universal remote control with this unit, please be aware
that the code number given may not operate this unit. In this case, please call the manufacturer of the universal remote control.
-6-
EN
9I03
T5505_7505UF(EN).QX33
04.4.12
10:01 AM
Page 7
OPERATING CONTROLS AND FUNCTIONS
This manual covers 13" and 19". The operation of the two models are exactly the same except
the appearance. 13" model is illustrated in this manual.
NOTE:
• We do not recommend the use of universal remote controls. Not all of the functions may be controlled with
a universal remote control.
If you decide to use a universal remote control with this unit, please be aware that the code number given
may not operate this unit. In this case, please call the manufacturer of the universal remote control.
- TV/VCR FRONT PANEL -
- REMOTE CONTROL [SRC2213W]
25
WAKE-UP
/SLEEP
POWER
3
1
2
3
4
5
6
7
8
9
0
+100
MENU
DISPLAY
MUTE
15
CHANNEL
16
17
8
VOLUME
PLAY
REW
F.FWD
26
24
5
4
23
9
10
STOP
7
11
18
TV/FM
CHANNEL
RETURN
RECORD
T-PROG.
CLEAR
SPEED
PAUSE/STILL
GAME
SLOW
COUNTER
RESET
19
20
[SRC2419]
22
21
25
WAKE-UP
/SLEEP
POWER
3
15
16
17
8
CHANNEL
RETURN
1
2
3
4
5
6
7
8
9
0
+100
MENU
DISPLAY
MUTE
CHANNEL
19
20
VOLUME
PLAY
REW
F.FWD
26
24
5
4
23
9
10
STOP
7
11
18
EJECT
RECORD
T-PROG.
CLEAR
COUNTER
RESET
SPEED
PAUSE/STILL
GAME
SLOW
22
21
1 VIDEO input jack– Connect to the video output
jack of your video camera, video game or another
VCR.
2 AUDIO input jack– Connect to the audio output
jack of your video camera, video game or another
VCR.
3 POWER button– Press to turn TV/VCR on and off.
Press to activate timer recording.
4 VOLUME X / Y buttons– Adjust the volume level.
5 CHANNEL K / L buttons– Press to select the
desired channels for viewing or recording, listening
of FM radio. (13 inch model only)
You may display the main menu on the TV screen
by pressing repeatedly this button on the TV/VCR
until you go below the lowest memcrized channel.
TRACKING function– Press to minimize video
‘noise’ (lines or dots on screen) during playback or
Slow mode. (See page 20.)
6 Remote Sensor Window– Receives the infrared
signals from the remote control.
7 STOP / EJECT button (TV/VCR)– Press to stop the
tape motion. Press in the Stop mode to remove tape
from TV/VCR.
STOP button (remote control)– Press to stop the
tape motion.
L button–
• Press to select setting modes from the on
screen menu.
• Press to enter digits when setting program.
(for example: setting clock or timer program)
-7-
EN
9I03
T5505_7505UF(EN).QX33
04.4.12
10:01 AM
Page 8
- REAR VIEW -
8 REW button– Press to rewind the tape, or to view
the picture rapidly in reverse during playback
mode. (Rewind Search)
s button–
• Press to select a mode from a particular menu.
(for example: LANGUAGE or USER’S SET
UP)
9 PLAY button– Press to begin playback.
K button–
• Press to select setting modes from the on
screen menu.
• Press to enter digits when setting program.
(for example: setting clock or timer program)
10 F.FWD button– Press to rapidly advance the tape,
or to view the picture rapidly in forward during
playback mode. (Forward Search)
B button–
• When setting program (for example: setting
clock or timer program), press to determine
your selection and proceed to the next step you
want to input.
• Press to determine setting modes from on screen
menu.
• Press to select a mode from a particular menu.
(for example: LANGUAGE or USER’S SET
UP)
11 REC button– Press for manual recording.
OTR button– Activates One Touch Recording.
(only on the TV/VCR)
12 RECORD indicator– Flashes during recording.
Lights up in the Stand-by mode for Timer Recording.
13 EARPHONE jack– Connects to earphones (not
supplied) for personal listening. The size of jack is
1/8” monaural (3.5mm).
14 Cassette compartment
15 Number buttons– Press to select desired channels
for viewing or recording. To select channels from
1 to 9, first press the 0 button and then 1 to 9.
+100 button– When selecting cable channels which
are higher than 99, press this button first, then press
the last two digits. (To select channel 125, first press
the “+100” button then press “2” and “5”).
16 MENU button– Press to display the main menu on
the TV screen.
17 DISPLAY button– Display the counter or the current channel number and current time on the TV
screen. (See page 25.)
18 SPEED button– Press to choose the desired
recording speed:SP/SLP.
19 T-PROG. CLEAR button– Press to cancel a setting
of timer program. (See page 23.)
COUNTER RESET button– Press to reset counter
to 0:00:00.
20 GAME button– Sets the game mode and selects front
A/V input mode at the same time. (See page 14.)
21 SLOW button– Press to start slow motion playback.
22 PAUSE/STILL button– Press to temporarily stop
the tape during the recording or to view a still picture during playback.
Frame Advance function– Press to advance the
picture one frame at a time during Still mode.
23 MUTE button– Mutes the sound. Press it again to
resume sound.
24 CHANNEL RETURN button– Press to go back to
the previously viewed channel. For example,
pressing this button once will change channel display from 3 (present channel) to 10 (previously
viewed channel), and pressing it a second time
will return from 10 to 3.
25 WAKE-UP/SLEEP button– Sets the Wake up or
Sleep Timer. (See pages 23 and 24.)
26 (13” model) TV/FM button– Sets the FM mode.
(19” model) EJECT button– Press to remove tape
from TV/VCR.
27 ANT. terminal– Connect to an antenna or cable
system.
28 Power cord– Connect to a standard AC outlet.
(120V/60Hz)
-8-
EN
9I03
T5505_7505UF(EN).QX33
04.4.12
10:01 AM
Page 9
PREPARATION FOR USE
ANTENNA/CABLE CONNECTIONS
From Cable System
or Satellite Dish
Satellite Box or
Cable Box
(Not supplied)
OUT
Rod Antenna
(Supplied with
13” model only)
VHF/UHF Antenna
(Not supplied)
IN
VHF Antenna
(Not supplied)
From
Cable System
UHF Antenna
(Not supplied)
or
ANT.
VHF/UHF
or Combiner
(Not supplied)
or
75-ohm Coaxial
Cable (Not supplied)
ANT.
or
Flat twin-lead cable
VHF/UHF COMBINED ANTENNA
VHF/UHF SEPARATE ANTENNAS
The VHF/UHF Rod Antenna (supplied with 13”
model only) is detachable. Insert the stem of the
antenna into the hole on the upper-back portion of
the TV/VCR. Connect the VHF/UHF Rod Antenna or
VHF/UHF Combination Antenna to the ANT. terminal of the TV/VCR as shown in the diagram. For the
best reception, fully extend the VHF/UHF Rod
Antenna and make the necessary adjustments. (Avoid
touching the top section when adjusting.)
NOTE:
Before connecting the Rod antenna into antenna terminal, check that the pin is not bent. If it is bent,
straighten the pin as illustrated, then plug the pin into
antenna terminal.
In some areas it will be necessary to use an outdoor
antenna.
Plug
(Needs to be straightened)
Use this connection if your cable system connects
directly to your TV/VCR without a converter box.
By using this connection you can:
1) Use the TV/VCR Remote Control to select channels.
2) Program one or more unscrambled channels for
Timer Recording.
NOTE: This unit will ONLY record and view the
same channel.
CABLE WITH CONVERTER/
DESCRAMBLER BOX OR SATELLITE
BOX
Bent pin
Cable
CABLE WITHOUT CONVERTER/
DESCRAMBLER BOX
(Straight pin)
NOTE:
The connection of an Rod antenna may not always
give acceptable TV reception.
If your cable service supplies you with a converter
box or if you use a satellite system, you can use the
basic connection shown in the diagram.
By using this connection you can also record scrambled channels. However, channel selection must be
made with the converter box or satellite box. This
means that channels cannot be changed using the
TV/VCR Remote Control. Unattended timer recording is limited to one channel at a time.
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical.
-9-
EN
9I03
T5505_7505UF(EN).QX33
04.4.12
10:01 AM
Page 10
TO RECORD A SCRAMBLED/UNSCRAMBLED
CHANNEL
1) Set the TV/VCR channel selector to the output
channel of the Cable Converter Box or Satellite
Box. (Example: CH3)
2) Select the channel to record from your Cable
Converter Box or Satellite Box.
FRONT A/V INPUT
INSTALLING THE BATTERIES
1)Open the battery compartment cover by pressing
the cover on the remote unit in the direction of the
arrow.
2)Insert 2 “AA” penlight batteries into the battery
compartment in the direction indicated by the
polarity (+/-) markings.
3)Replace the cover.
When using an external input signal (another VCR,
video game or video camera), connect the player’s
audio/video output cables to the AUDIO IN/ VIDEO
IN jacks of your TV/VCR. Then press the CHANNEL K or L button until “AUX” appears on the
screen.
NOTE: “AUX” is found below the
AUX
lowest memorized channel.
(Example: CH2)
SET UP FOR USE
SELECTING THE LANGUAGE
1
Plug in the TV/VCR power cord
Plug the TV/VCR power cord into a
standard AC outlet.
NOTE:
• If some digits appear in the corner of
the screen, press the POWER button
without unplugging the power cord.
4
Make sure ...
• Press the POWER button to turn on the TV/VCR.
NOTE: This function effects only the language on
the screen menu and not the audio source.
2
Select “LANGUAGE”
Press the MENU button on the
remote control.
Press the PLAY/K or STOP/L button to point to “LANGUAGE”.
3
–MENU–
TIMER PROGRAMMING
PICTURE CONTROL
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
B LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SERARCH
INDEX SEARCH
Select “ENGLISH”, “ESPAÑOL” or
“FRANÇAIS”
Select “ENGLISH”, “ESPAÑOL”= Spanish or
“FRANÇAIS”= French using the F.FWD/B or
REW/s button.
Exit the Language mode
Press the MENU button on the remote control to
return to TV mode.
NOTE: If for some reason the menu is in Spanish or
French, press the MENU button on the remote control, press the PLAY/K button to point to “IDIOMA
[ESPAÑOL]” or “LANGAGE [FRANÇAIS]”, then
press the F.FWD/B button, then press the MENU
button on the remote control.
CLOCK SET UP
(AUTO / MANUAL)
The TV/VCR clock must be set correctly before timer
recording is possible. It is suggested that the clock be
set manually when first setting up the TV/VCR. Then,
set to [ON] the auto clock setting which will periodically correct the setting if necessary.
NOTE: If you cannot receive a station with time
signals, auto clock setting cannot be performed. Use
manual setting only.
MANUAL CLOCK SETTING
Make sure ...
• The TV/VCR is turned on.
- 10 -
EN
9I03
T5505_7505UF(EN).QX33
04.4.12
10:01 AM
Page 11
In the example below, the clock is to be set to:
DATE
May 6th, 2004
SETTING TIME 5:40PM
1
3
Select the month
Press the PLAY/K or STOP/L
button until your desired month
appears. (Example: May → 05)
Then, press the F.FWD/B button.
4
Select the day
Press the PLAY/K or STOP/L button until your desired day appears.
(Example: 6th → 06)
Then, press the F.FWD/B button.
5
Select the year
Press the PLAY/K or STOP/L button until your desired year appears.
(Example: 2004)
Then, press the F.FWD/B button.
6
Select the hour
Press the PLAY/K or STOP/L button until your desired hour appears.
(Example: 5, PM)
Then, press the F.FWD/B button.
7
–MENU–
TIMER PROGRAMMING
PICTURE CONTROL
B SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
Select “MANUAL CLOCK SET”
Press the PLAY/K or STOP/L
button to point to “MANUAL
CLOCK SET”.
Then, press the F.FWD/B button.
Select the minute
Press the PLAY/K or STOP/L button until the desired minute
appears. (Example: 40)
Start the clock
5:40 PM
Select “SETTING CLOCK”
Press the MENU button on the
remote control.
Press the PLAY/K or STOP/L
button to point to “SETTING
CLOCK”.
Then, press the F.FWD/B button.
2
8
Press the MENU button on the
remote control.
Although seconds are not displayed, they begin counting from
00 when you press the MENU button on the remote control. Use this
feature to synchronize the clock with the correct
time.
NOTE:
When unplugging the AC cord or if there is a power
failure for more than 3 seconds, you may have to
reset the clock.
– SETTING CLOCK –
AUTO CLOCK
[ON]
AUTO CLOCK CH SEARCH
AUTO CLOCK CH
[ 02 ]
B MANUAL CLOCK SET
D.S.T.
[OFF]
– MANUAL CLOCK SET –
MONTH DAY
05 / ––
HOUR
YEAR
––– ––––
MINUTE
–– : ––
––
– MANUAL CLOCK SET –
MONTH DAY
05 / 06
HOUR
YEAR
––– ––––
MINUTE
–– : ––
––
TO CHANGE CLOCK SETTING
If you want to change the clock,
1)Follow steps [1] and [2].
2)Select where you want to change using the
F.FWD/B or REW/s button.
3)Enter correct numbers using the PLAY/K or
STOP/L button.
4)Press the MENU button on the remote control to
start the clock.
PLEASE NOTE:
If there is no local PBS station in your area or on
your cable system, select “AUTO CLOCK” and
press the F.FWD/B or REW/s button to turn [OFF]
this function. Then you can manually adjust the
clock.
AUTOMATIC CLOCK SETTING
– MANUAL CLOCK SET –
MONTH DAY
05 / 06
HOUR
YEAR
THU
2004
MINUTE
–– : ––
––
– MANUAL CLOCK SET –
MONTH DAY
05 / 06
HOUR
YEAR
THU
2004
MINUTE
05 : ––
PM
– MANUAL CLOCK SET –
MONTH DAY
05 / 06
HOUR
YEAR
THU
MINUTE
05 : 40
PM
2004
Make sure ...
• The TV/VCR is turned on.
• Confirm the TV/VCR is receiving a RF (Radio
Frequency) signal from either an antenna or cable
system connection using the ANT. terminal on the
rear of the TV/VCR.
NOTE:
• If a cable converter box is being used, make sure it
is powered on.
• You must use the TV/VCR remote control to perform the clock setting procedure.
• If the TV/VCR is connected directly to a cable
converter box or satellite box, the local PBS station must be selected on the cable box itself, and
the TV/VCR must be set to the output channel of
the cable converter box or satellite box (usually
channel 3 or 4), to be able to set up or correct the
clock automatically.
- 11 -
EN
9I03
T5505_7505UF(EN).QX33
1
04.4.12
10:01 AM
DAYLIGHT-SAVING TIME
– SETTING CLOCK –
B AUTO CLOCK
[ON]
AUTO CLOCK CH SEARCH
AUTO CLOCK CH
[ 02 ]
MANUAL CLOCK SET
D.S.T.
[OFF]
Begin “AUTO CLOCK CH SEARCH”
Press the STOP/L button to select
“AUTO CLOCK CH SEARCH”.
Press the F.FWD/B button.
• The TV/VCR is now searching
for the station which contain the
auto clock set signal. The search
for a signal may take up to 20
seconds per channel.
• “_ _” appears at the lower left of
the screen when the search has
ended.
• Auto Clock station- write down
the number(s) that appear on the
screen. These are the auto clock
station(s) in your area. See item 4 below.
• If no number(s) appear on the TV screen, there are
no stations in your area which contain the Auto
Clock signal. Auto Clock Setting is not possible.
Please use Manual Clock Setting on pages 10-11.
Press the MENU button to exit the screen.
NOTE: During Auto Clock CH Search, the picture
may be distorted. This is normal.
– SETTING CLOCK –
AUTO CLOCK
[ON]
B AUTO CLOCK CH SEARCH
AUTO CLOCK CH
[ 02 ]
MANUAL CLOCK SET
D.S.T.
[OFF]
– AUTO CLOCK CH SEARCH –
08
10
13
__
4
Enter the channel number that contains the
Automatic Clock Setting Signal
Press the MENU button on the
remote control.
Press the PLAY/K or STOP/L button to select “SETTING CLOCK”.
Press the F.FWD/B button to enter
“SETTING CLOCK” menu.
Press the STOP/L button to select
“AUTO CLOCK CH”.
Press the F.FWD/B or REW/s
buttons until you locate Auto
Clock Set station number. See item
3 above.
Press the MENU button to exit the screen.
–MENU–
TIMER PROGRAMMING
PICTURE CONTROL
B SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
Turn off the TV/VCR
Once the TV/VCR is turned off , it will periodically
check and set the correct date and time.
–MENU–
TIMER PROGRAMMING
PICTURE CONTROL
B SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
Set “AUTO CLOCK” to [ON]
Press the F.FWD/B button until
“AUTO CLOCK [ON]” appears.
3
5
Select “SETTING CLOCK”
Press the MENU button on the
remote control.
Press the PLAY/K or STOP/L button to select “SETTING CLOCK”.
Press the F.FWD/B button to enter
“SETTING CLOCK” menu.
2
Page 12
Select this feature and the TV/VCR’s clock automatically will advance one hour in April, then reverse one
hour in October.
When Daylight-Saving Time is ON, the clock will
change automatically as follows:
• First Sunday of April : At 2 AM the clock immediately changes to 3 AM. Any timer programming
you have set to occur between 2 AM and 3 AM
will not record.
• Last Sunday of October : At 2 AM the clock
immediately changes to 1 AM.
Make sure ...
• Press the POWER button to turn on the TV/VCR.
1
Select “SETTING CLOCK”
Press the MENU button on the
remote control.
Press the PLAY/K or STOP/L button to point to “SETTING
CLOCK”.
Then, press the F.FWD/B button.
2
Set “D.S.T.” (Daylight-Saving Time) to [ON]
Press the PLAY/K or STOP/L button to point to “D.S.T.”.
Then, press the F.FWD/B or
REW/s button until [ON] appears.
3
–MENU–
TIMER PROGRAMMING
PICTURE CONTROL
B SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
– SETTING CLOCK –
AUTO CLOCK
[ON]
AUTO CLOCK CH SEARCH
AUTO CLOCK CH
[ 02 ]
MANUAL CLOCK SET
B D.S.T.
[ON]
Exit the Daylight-Saving Time mode
Press the MENU button on the remote control to
return to TV mode.
TO CANCEL THE DAYLIGHT-SAVING
TIME
Repeat steps [1] to [2], select [OFF] using the
F.FWD/B or REW/s button.
– SETTING CLOCK –
AUTO CLOCK
[ON]
AUTO CLOCK CH SEARCH
B AUTO CLOCK CH
[ 45]
MANUAL CLOCK SET
D.S.T.
[OFF]
- 12 -
EN
9I03
T5505_7505UF(EN).QX33
04.4.12
10:01 AM
Page 13
DELETING (OR ADDING)
CHANNEL
CHANNEL SET UP
You can program the tuner to scan all the channels
you receive in your area.
NOTE: Channel memory programming is NOT
needed when connected to a cable box or satellite
box. Just select the TV/VCR channel selector to the
output channel of the cable box or satellite box (Ex
CH3). Then select the channel to be viewed on the
Cable Box or Satellite Box.
The channels you no longer receive or seldom watch
can be deleted from the memory. (Of course, you
can add the deleted channel into the memory again.)
1
Make sure ...
• Press the POWER button to turn on the TV/VCR.
1
2
–MENU–
TIMER PROGRAMMING
PICTURE CONTROL
SETTING CLOCK
B CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
Select “ADD/DELETE CH”
Press the PLAY/K or STOP/L button to point to “ADD/DELETE
CH”.
Press the F.FWD/B button.
3
Begin auto preset
Press the PLAY/K or STOP/L button to point to “AUTO CH PROGRAMMING”.
Then, press the F.FWD/B button.
The tuner scans and memorizes all
the active channels in your area.
3
–MENU–
TIMER PROGRAMMING
PICTURE CONTROL
SETTING CLOCK
B CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
Select “CHANNEL SET UP”
Press the MENU button on the
remote control.
Press the PLAY/K or STOP/L button to point to “CHANNEL SET
UP”.
Then, press the F.FWD/B button.
2
Select “CHANNEL SET UP”
Press the MENU button on the
remote control.
Press the PLAY/K or STOP/L button to point to “CHANNEL SET
UP”.
Then, press the F.FWD/B button.
– CHANNEL SET UP –
ADD / DELETE CH (CATV)
B AUTO CH PROGRAMMING
– CHANNEL SET UP –
B ADD / DELETE CH (CATV)
AUTO CH PROGRAMMING
Enter the desired channel number
Press the PLAY/K or STOP/L button until your desired channel num08
ber appears. (You can also use the
number buttons or the CHANNEL
K/L button to enter it) (Example:
CH8)
• When selecting cable channels which are higher
than 99, press the +100 button first, then, press the
last two digits. (Example: to select channel 125,
first press the +100 button then press “2” and “5”).
• You must proceed single-digit channel numbers
with a zero (Example: 02 ... 09).
ADD / DELETE
After scanning
The tuner stops on the lowest memorized channel.
• When AUTO CH PROGRAMMING is activated
where there is no TV signal input, “NO TV SIGNALS” will appear on the display after the completion of the channel scanning.
• The TV/VCR may display TV channels to be
CATV channels caused by poor antenna reception.
In this case, try auto preset again.
4
Delete (or add) it from (into) memory
Press the F.FWD/B or REW/s button. The channel
number changes to light red. The channel is deleted
from memory.
• To delete another channel, repeat steps [3] and [4].
• If you press the F.FWD/B or REW/s button
again, the channel is memorized again.
Added channel: Light blue.
Deleted channel: Light red.
5
Exit the channel setup mode
Press the MENU button on the remote control to
returns to TV mode.
NOTE: To confirm that channel(s) has been deleted
or added, press the CHANNEL K or L button.
- 13 -
EN
9I03
T5505_7505UF(EN).QX33
04.4.12
10:01 AM
Page 14
TV OPERATION
WATCHING A TV PROGRAM
1
PICTURE CONTROL
Turn on the TV/VCR
Press the POWER button to turn on the TV/VCR.
2
Select the channel number
Press the CHANNEL K or L button to select your
desired channel number or press the number buttons
on the remote control.
Remember: If the TV/VCR is connected to a cable
box or satellite box, the TV/VCR must be on CH3 or
CH4, then the channel to be viewed must be selected
on the cable box or satellite box.
3
The TV/VCR’s picture controls – BRIGHT, CONTRAST, COLOR, TINT and SHARPNESS – are
preset to factory specifications. Although they are
usually the best, you may need to make some further
adjustments for a natural looking image.
NOTES:
• Procedures must be followed within 5 seconds or
the Picture Control mode will be cancelled.
• When setting the Picture Control, the Game mode
will be cancelled.
Make sure ...
• TV/VCR power must be turned on.
1
Adjust sound
Press the VOLUME X or Y button
to adjust the volume.
VOLUME
20
C C C C C CCCCCCC
GAME MODE
This function enables you to decrease the TV screen
contrast and making it suitable for use with a Video
game system.
NOTE: This function CANNOT be set during
recording.
Press the GAME button on the
remote control. “GAME” appears
on the screen.
Select “PICTURE CONTROL”
Press the MENU button on the
remote control.
Press the PLAY/K or STOP/L button to point to ”PICTURE CONTROL”.
Then, press the F.FWD/B button.
2
–MENU–
TIMER PROGRAMMING
B PICTURE CONTROL
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
Select item you want to adjust
Press the PLAY/K or STOP/L button until desired
control is displayed.
BRIGHT
CONTRAST
COLOR
TINT
SHARPNESS
GAME
BRIGHT
–PPPPPPPCPPPPPPP+
When you press the GAME button;
• The TV/VCR turns on automatically.
• The TV/VCR will select front A/V input mode
3
Adjust the picture control
Press the F.FWD/B or REW/s button to adjust to
your desired level.
automatically.
TO CANCEL THE GAME MODE
Press the GAME button or CHANNEL K or L button on the remote control.
COLOR
REW/s
to decrease
brightness
to decrease
contrast
to pale
F.FWD/B
to increase
brightness
to increase
contrast
to brilliant
TINT
SHARPNESS
to purple
to soft
to green
to clear
BRIGHT
DEGAUSSING
CONTRAST
This television has a degaussing circuit that will clear
up color errors on the TV screen that are caused by
any excess magnetism which happens to get too close
to the TV. This circuit is designed to operate once
when the set is first plugged in. If minor color errors
are seen in some locations on the screen, please
unplug the TV for approximately 15 minutes. When
the TV is plugged back in, the degaussing circuit will
operate once to clear them up. Repeat this procedure
any time the TV screen is accidentally magnetized, or
when the TV is moved or relocated.
• If there is a power failure of any kind, the unit will
- 14 -
retain its setting.
EN
9I03
T5505_7505UF(EN).QX33
04.4.12
10:01 AM
Page 15
CLOSED CAPTION SYSTEM
WHEN THE CLOSED CAPTION MODE
IS ON
You can view specially labeled (cc) TV programs,
movies, news, pre-recorded tapes with either a dialogue caption or text display.
CAPTION mode: By choosing the caption mode, you
can watch dramas, movies and news while captioning
the dialogues and the contents of news.
TEXT mode: By choosing the text mode, you can
watch half screen text information if you want.
1-2: You may get these captions or text information
by selecting either “1” or “2”. Caption “2” is usually
used for a second language if available.
The On-Screen Display will disappear after 5 seconds.
• This is also true when the MUTE button is pressed,
and when the PAUSE/STILL button is pressed
while recording.
• If there is a power failure of any kind, the unit will
retain its memory for this feature.
NOTE:
Not all programs are broadcast with closed captions. Your
TVCR is designed to provide error free closed captions
from high quality antenna, cable and VCR signals.
Conversely, poor quality signals are likely to result in caption errors or no captions at all. Common signal conditions
which may cause captions errors are listed below:
• Automobile ignition noise
• Electric motor noise
• Weak snowy reception on TV screen
• Multiplex signal reception displaying picture
ghosts or airplane flutter.
• Playback of poorly recorded or worn VCR tapes.
• If the TV/VCR displays a black box
on the TV screen, this means that the
TV/VCR is set to the TEXT mode.
To clear screen, select [CAPTION1],
[CAPTION2] or [OFF].
Make sure ...
• TV/VCR is turned on.
• You have the TV/VCR remote control.
V-CHIP SET UP
V-CHIP SET UP
1
2
1
Select “CAPTION”
2
Select your desired caption menu
Press the F.FWD/B or REW/s button
until your desired caption menu appears.
([CAPTION1], [CAPTION2], [TEXT1]
or [TEXT2])
3
Enter Access code
ACCESS CODE
_ _ _ _
3
Select “TV RATING”
Press the PLAY/K or STOP/L button to select “TV RATING”.
Then, press the F.FWD/B button.
–MENU–
TIMER PROGRAMMING
PICTURE CONTROL
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
B CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
–MENU–
TIMER PROGRAMMING
PICTURE CONTROL
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
B V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
Use the numbers on the remote
control to enter the access code.
• For the first time set-up or in the
event the TV/VCR has lost
power, enter the default code of the numbers:
0000.
Make sure ...
• TV/VCR power must be turned on.
Press the MENU button on the
remote control.
Press the PLAY/K or STOP/L button to point to “CAPTION”.
Select “V-CHIP SET UP”
Press the MENU button on the
remote control.
Press the PLAY/K or STOP/L button to select “V-CHIP SET UP”.
Then, press the F.FWD/B button.
4
– V-CHIP SET UP –
B TV RATING
MPAA RATING
CHANGE CODE
Blocking TV programs
Press the PLAY/K or STOP/L button to select “TV rating” that you
wish to block.
•When you select the rating category and turn it [BLOCK], the higher rating will turn
[BLOCK] automatically. Also, the lower rating will
turn [VIEW] automatically.
• When you turn “TV-Y” to [VIEW], then all ratings
will turn to [VIEW] automatically.
B TV–Y
TV–Y7 (
TV–G
TV–PG (
TV–14 (
TV–MA (
–MENU–
TIMER PROGRAMMING
PICTURE CONTROL
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
B CAPTION [CAPTION1]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
Exit the caption setting mode
Press the MENU button on the remote control to
return to TV mode.
TO CANCEL THE CLOSED CAPTION SYSTEM
Repeat steps [1] and [2], select [OFF] using the
F.FWD/B or REW/s button. Press the MENU button on the remote control to return to TV mode.
- 15 -
)
)
)
)
[VIEW]
[VIEW]
[VIEW]
[VIEW]
[VIEW]
[VIEW]
Selection
TV-Y
TV-Y7
TV-G
TV-PG
TV-14
Rating Category Explanations
Appropriate for all children
Appropriate for children seven and older
General Audience
Parental Guidance suggested.
Unsuitable for children under 14
TV-MA
Mature audience only
EN
9I03
T5505_7505UF(EN).QX33
5
04.4.12
10:01 AM
Page 16
CHANGING V-CHIP BLOCKED PROGRAMMING
Exit the V-Chip setting mode
Press the MENU button on the remote control to
enter the setting and exit the screen.
V-CHIP SET UP SUB RATINGS
When you select the ratings of TV-Y7,TV-PG,TV-14
or TV-MA you will have the option of selecting sub
rating categories.
1
Select “V-CHIP SET UP”
Press the MENU button on the
remote control.
Press the PLAY/K or STOP/L button to select “V-CHIP SET UP”.
Then, press the F.FWD/B button.
2
–MENU–
TIMER PROGRAMMING
PICTURE CONTROL
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
B V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
_ _ _ _
2
– V-CHIP SET UP –
B TV RATING
MPAA RATING
CHANGE CODE
Selecting Sub-Ratings”
3
TV–Y7
ACCESS CODE
Select “MPAA RATING”
Press the PLAY/K or STOP/L button to point to “MPAA RATING”.
Then, press the F.FWD/B button.
_ _ _ _
– V-CHIP SET UP –
TV RATING
B MPAA RATING
CHANGE CODE
[BLOCK]
[BLOCK]
TV–PG
5
Enter Access code
–MENU–
TIMER PROGRAMMING
PICTURE CONTROL
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
B V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
Use the numbers on the remote
control to enter the access code.
Press the STOP/L button to select the sub-rating you
wish to block. Then, press the F.FWD/B button.
• When you select [TV-Y7]:
Press the STOP/L or PLAY/K
button to select “FV” (Fantasy
Violence).
Then, press the F.FWD/B button
to select [BLOCK] or [VIEW].
• When you select [TV-PG], [TV-14] or [TV-MA]:
Press the STOP/L or PLAY/K
button to select “D”(Suggestive
Dialog), “L”(Coarse Language),
“S”(Sexual Situation), or
“V”(Violence). Then, press the
F.FWD/B button to select [BLOCK] or [VIEW].
Note: When you select [TV-MA], “D” does not
appear on the TV screen.
• The sub-ratings which set to
[BLOCK] appears next to the rating category in the TV rating
menu.
B FV
Select “V-CHIP SET UP”
Press the MENU button on the
remote control.
Press the PLAY/K or STOP/L button to select “V-CHIP SET UP”.
Then, press the F.FWD/B button.
ACCESS CODE
Select “TV RATING”
Press the PLAY/K or STOP/L button to select “TV RATING”.
Then, press the F.FWD/B button.
4
MPAA RATING SET UP
1
Enter Access code
Use the number buttons on the remote
control to enter the access code.
Note: Default code is 0000.
3
Note: To change the rating, the TV/VCR must be
turned to a station that is not protected. If the (PROTECTED) appears on the screen, please change the
channel to a station that is not protected.
1)Follow steps [1] and [2].
2)Press the F.FWD/B button to select "TV RATING". Select a TV rating to be unblocked by pressing the PLAY/K or STOP/L button.
Then press the F.FWD/B button to unblock the
rating.
3)Press the MENU button on the remote control to
exit the screen.
4
[BLOCK]
B D
L
S
V
[BLOCK]
[BLOCK]
[BLOCK]
[BLOCK]
B TV–Y
TV–Y7 (
)
TV–G
TV–PG (DLSV )
TV–14 (DLSV )
TV–MA ( LSV )
[VIEW]
[VIEW]
[VIEW]
[BLOCK]
[BLOCK]
[BLOCK]
Selection
G
PG
PG-13
R
G
PG
PG–13
B R
NC–17
X
[VIEW]
[VIEW]
[VIEW]
[BLOCK]
[BLOCK]
[BLOCK]
NC-17
Rating Category Explanations
General Audience
Parental Guidance suggested.
Unsuitable for children under 13
Restricted; under 17 requires accompanying parent or adult guardian
No one under 17 admitted
X
Mature audience only
• When you select the rating category and turn it
Exit the V-Chip setting mode
Press the MENU button on the remote control to
enter the setting and exit the screen.
Select your desired item
Press the PLAY/K or STOP/L button to point to your desired item.
Then, press the F.FWD/B button to
select [BLOCK] or [VIEW].
•
- 16 -
[BLOCK], the higher rating will turn [BLOCK]
automatically. Also, the lower rating will turn
[VIEW] automatically.
When you turn “G” to [VIEW], then all ratings
will turn to [VIEW] automatically.
EN
9I03
T5505_7505UF(EN).QX33
5
04.4.12
10:01 AM
Page 17
5
Exit the V-Chip setting mode
Press the MENU button on the remote control to
enter the setting and exit the screen.
CHANGE ACCESS CODE
To change access code, follow the steps.
1
FM MODE (13” MODEL ONLY)
Select “V-CHIP SET UP”
Press the MENU button on the remote control.
Press the PLAY/K or STOP/L button to select “VCHIP SET UP”.
Then, press the F.FWD/B button.
2
Enter Access code
Use the number on the remote control to enter the access code.
Note: The default code is 0000.
3
Select “CHANGE CODE”
Press the PLAY/K or STOP/L button to select "CHANGE CODE".
Then, press the F.FWD/B button.
4
Exit the V-Chip setting mode
Press the MENU button on the remote control to exit
the screen.
Note: If you unplug the power code or power failure
occurs, the changed access code will be lost and will
return to default (0000). Change your access code
again as necessary.
ACCESS CODE
This function enables you to receive FM radio broadcasting.
1
Set the FM mode
Press the TV/FM button on the
remote control. The radio frequency
appears on the TV screen.
FM 88.0 MHz
_ _ _ _
2
– V-CHIP SET UP –
TV RATING
MPAA RATING
B CHANGE CODE
Enter New code
Use the number buttons to enter
your desired access code in the
NEW CODE space. Then enter
the same code in the CONFIRM
CODE space. V-CHIP SET UP
screen appear on the screen.
• If you enter wrong code, repeat step 4, making
sure you enter the same new code exactly in the
confirm code space.
NEW CODE
XXXX
CONFIRM CODE
_ _ _ _
Select the radio frequency you want to receive
Press the CHANNEL K or L button until your
desired radio frequency appears.
NOTES:
• The radio frequency indication repeats to appear
and disappear.
• You can not record the FM radio station.
• If you receive a weak radio signal, you may change
the FM Antenna mode to INT(internal) or
EXT(external) by following the step below.
1)Press the MENU button. Press the PLAY/K or
STOP/L button to point to “CHANNEL SET UP”.
Then, press the F.FWD/B button.
2)Press the PLAY/K or STOP/L button to point to
“FM ANTENNA”. Select [INT] or [EXT] using
the F.FWD/B or REW/s button.
PLAYBACK
This TV/VCR will operate with any cassette that has the
mark. For best results, we
recommend the use of high-quality tapes. Do not use poor quality or damaged tapes.
INSERTING A CASSETTE
PRECAUTIONS
Insert the cassette in the direction as shown. Push in
gently, but continuously, on the center-back of the
cassette until it is drawn into the TV/VCR. The
TV/VCR will automatically turn on.
Window
• Avoid moisture. Moisture condensation may occur
•
CORRECT
WRONG
•
•
- 17 -
on the tape if it is moved from a cold place to a
warm place or visa versa. Before using a tape with
these conditions, to avoid damage of the tape and
your TV/VCR, wait until the tape has warmed to
room temperature and the moisture has evaporated.
Avoid extreme heat, high humidity and magnetic
fields from speaker systems.
Do not tamper with the cassette mechanism.
Do not touch the tape with your fingers.
EN
9I03
T5505_7505UF(EN).QX33
04.4.12
10:01 AM
Page 18
TO CANCEL THE REPEAT PLAY MODE
NORMAL PLAYBACK
Repeat steps [1] and [2], select [OFF] using the
F.FWD/B or REW/s button on the remote control.
Press the MENU button on the remote control to
return to TV mode.
If there is a power failure of any kind, the unit
will retain its memory for this feature.
Make sure ...
• TV/VCR power must be turned on.
1
Insert a prerecorded tape
If the erase-protection tab has been removed, the
TV/VCR will start playback automatically.
2
SEARCH
To begin playback
PLAY B
PICTURE SEARCH
Press the PLAY button.
Note: If any menu is activated on
the screen, the PLAY button does
not function. Press the MENU button to clear the menu, then press the PLAY button.
3
To stop playback
Press the STOP button when playback is completed.
AUTO REPEAT PLAYBACK
The TV/VCR has an auto repeat function that allows
you to repeat a tape indefinitely without touching the
PLAY button.
ALL REPEAT: Repeat playback from the beginning
to the end of the tape.
BLANK REPEAT: Repeat playback from the beginning to a blank part of more than 10 seconds.
1
Select “USER’S SET UP”
–MENU–
Press the MENU button on the
remote control.
Press the PLAY/K or STOP/L button to point to “USER’S SET UP”.
Then, press the F.FWD/B button.
2
TIMER PROGRAMMING
PICTURE CONTROL
SETTING CLOCK
CHANNEL SET UP
B USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
Select “ALL” or “BLANK”
ZERO RETURN
This function allows you to search easily a beginning
point that you want to review by rewinding or fast
forwarding.
NOTE:
Zero Return WILL NOT work on a blank tape or a
blank portion of a tape.
1
RENTAL
B REPEAT PLAY
AUTO RETURN
[OFF]
[ALL]
[OFF]
Exit the Repeat Play setting
Stop a tape at your desired point
Rewind or fast forward the tape to the beginning
point from which you want to review.
2
– USER’S SET UP –
Press the PLAY/K or STOP/L button to point to “REPEAT PLAY”.
Press the F.FWD/B or REW/s
button repeatedly until your desired
selection [ALL] or [BLANK] appears.
3
This feature is very useful in finding or skipping over
a particular scene on a tape. In this mode, the sound
will be muted.
1)You may view a video tape at a high speed in
either a forward or reverse direction by pressing
the F.FWD or REW button during playback (in the
SP / LP / SLP modes).
2)Press it again and the TV/VCR will now search in
super high speed (in the LP / SLP modes only).
NOTE: Tapes recorded in the SP or LP mode will
display a noise bar on the TV screen and the picture may revert to Black and White. This is normal.
3)Press the PLAY button to return to normal speed.
Reset the counter to 0:00:00
Press the COUNTER RESET button repeatedly.
3
Begin recording or playback
Press the RECORD or PLAY button.
Press the STOP button when recording or playback is
completed.
Press the MENU button on the remote control to
return to the TV mode.
4
To activate “ZERO RETURN”
mode
4
Start playback
Press the PLAY button to start the Repeat Play.
”REPEAT PLAY B” appears.
• Once you select the Repeat Play mode, it stays in
effect even after you turn off the TV/VCR.
• If the Rental mode is set [ON], the “RENTAL
PLAY B” display has priority.
–MENU–
TIMER PROGRAMMING
PICTURE CONTROL
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
B ZERO RETURN
TIME SEARCH
INDEX SEARCH
Press the MENU button on the
remote control.
Press the PLAY/K or STOP/L button to point to “ZERO RETURN”.
Then, press the F.FWD/B button.
The counter will appear on the TV screen.
The tape will automatically stop when the counter
returns to 0:00:00.
- 18 -
EN
9I03
T5505_7505UF(EN).QX33
04.4.12
10:01 AM
Page 19
TIME SEARCH
• After index search, the TV/VCR will play the tape
The Time Search function makes it possible to quickly advance the tape to your desired position simply by
entering the exact amount of playback time you want
to skip.
NOTES:
• Time Search can be set up to a maximum of 9
hours 50 minutes (9:50) by 10 minutes at a time.
• This function will not operate in recording mode.
In the example below: To watch a program that is 2
hours, 50 minutes from the present tape position, in
either direction.
1
Insert a tape.
2
Select “TIME SEARCH” mode
SLOW MOTION
Press the SLOW button to reduce the playback speed.
The TV/VCR mutes the sound during slow motion.
Press the PLAY button to return to normal playback.
NOTE: If left in the Slow mode for more than five
minutes, the TV/VCR will automatically go into the
Stop mode.
RENTAL PLAYBACK
This function enables you to improve the picture
quality when playing back worn cassettes such as
rented tapes.
1
Enter your desired time
Press the PLAY/K or STOP/L button until your
desired time appears. (Example: “2:50” stands for 2
hours 50 minutes)
If you wish to cancel the Time Search at this point,
press the MENU button on the remote control.
4
video tape cannot be detected.
TIME SEARCH
2 : 50
Press the TIME SEARCH button
(with each push it will increase by
10 minutes).
3
automatically.
• In some cases, the index mark at the beginning of
2
Begin Time Search
By pressing the REW/s or F.FWD/B button, the
TV/VCR will rewind or fast forward to the specified
point.
The time counts down as the searching progresses.
When 0:00 is reached, the tape will start playback
automatically.
TO CANCEL THE TIME SEARCH at this
point
Press the STOP/EJECT button on the TV/VCR or the
remote control. This will delete the selected time.
INDEX SEARCH
Select “USER’S SET UP”
Press the MENU button on the
remote control.
Press the PLAY/K or STOP/L button to point to “USER’S SET UP”.
Then, press the F.FWD/B button.
Set “RENTAL” to [ON]
Press the PLAY/K or STOP/L button to point to “RENTAL”.
Press the F.FWD/B or REW/s
button until [ON] appears.
3
–MENU–
TIMER PROGRAMMING
PICTURE CONTROL
SETTING CLOCK
CHANNEL SET UP
B USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
– USER’S SET UP –
B RENTAL
REPEAT PLAY
AUTO RETURN
[ON]
[OFF]
[OFF]
Exit the Rental setting
Press the MENU button on the remote control to
return to the TV mode.
4
Start playback
Press the PLAY button to start playback. “RENTAL
PLAY B” appears.
• Once you select the Rental mode, it stays in effect
even after you turn off the TV/VCR.
An index signal is recorded on the tape automatically
when the recording is started. To view a recording at a
specific start point:
TO CANCEL THE RENTAL MODE
1)Press the MENU button on the
Repeat steps [1] and [2], select [OFF] using the
remote control. Press the PLAY/K
F.FWD/B or REW/s button on the remote control.
or STOP/L button to point to
Press
the MENU button on the remote control to
“INDEX SEARCH”, then press
return
to TV mode.
the F.FWD/B button.
If
there
is a power failure of any kind, the unit
2)Press the PLAY/K or STOP/L button within 30 secwill
remember
the setting.
onds until the number of programs that you want to
skip appears.
3)Press the F.FWD/B or REW/s button to start
index search. If you want to go forward, press the
F.FWD/B button. If you want to go back, press the
REW/s button.
- 19 EN
–MENU–
TIMER PROGRAMMING
PICTURE CONTROL
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
B INDEX SEARCH
9I03
T5505_7505UF(EN).QX33
04.4.12
10:01 AM
Page 20
VERTICAL HOLD CONTROL
TRACKING ADJUSTMENT
In the Pause/Still mode only, when the picture begins
to vibrate vertically, stabilize the picture by pressing
the CHANNEL K or L button.
NOTE:
If there are video noise lines on the screen, see Tracking
Adjustment section.
STILL PICTURE
You can view a still picture on the TV screen during
playback (the Still mode). Press the PAUSE/STILL
button during playback. Only tapes recorded in the
SLP mode will show the least amount of lines. Press
the PLAY button to return to playback.
NOTES:
• You can advance the picture one frame at a time by
pressing the PAUSE/STILL button during the Still
mode.
• If it is left in the Still mode for more than five minutes, the TV/VCR will automatically switch to the
Stop mode.
• Tracking adjustment will be set automatically
(Digital Tracking function) when you start playback.
• However when playing pre-recorded tapes or tapes
recorded on units other than your own, noise lines
(black and white streaks) may appear on the playback picture. If this occurs, you can adjust the
tracking control manually by pressing the CHANNEL K or L button until the streaks disappear. To
return to the DTR function, stop the tape once and
start playback again.
You
can reduce the noise lines by pressing the
•
CHANNEL K or L button in slow mode, too.
Tracking adjustment in Slow mode will not be set
automatically.
NOTE:
• In Still mode, press the SLOW button and press the
CHANNEL K or L button until streaks disappear.
To return to Still mode, press the PAUSE/STILL
button again.
RECORDING
Before recording, make sure:
The desired channel is selected by pressing the number buttons on the remote control or the CHANNEL
Up/Down button. (If the TV/VCR is connected to a
cable box or satellite box, the TV/VCR must be on
CH3 or CH4, then the channel to be recorded is
selected on the cable box or satellite box. )
There is a tape with its safety tab into the VCR.
The desired recording speed is selected in SP(standard play) or SLP(super long play) mode by pressing the SPEED button on the remote control.
Tape Speed
Type of tape
Recording/Playback Time
T60
T120
T160
SP mode
1 hour
2 hours
2-2/3 hours
SLP mode
3 hours
6 hours
8 hours
ERASE PREVENTION
You can prevent accidental erasing of recording
by breaking off the tab
on the back edge of the
cassette.
Tab
If you decide to record
on the tape again, cover
the hole with plastic
tape.
Make sure ...
• TV/VCR power is turned on.
• Insert a cassette tape with its erase prevention tab
in place. (If necessary, rewind or fast forward the
tape to the point at which you want to begin
recording.)
NOTE: This unit will ONLY record and view the
same channel.
NORMAL RECORDING
1)Begin the recording by pressing the RECORD button.
To temporarily stop recording or resume it, press
the PAUSE/STILL button. After the TV/VCR has
been in Pause mode for 5 minutes, it will stop
automatically to protect the tape and the video
head.
NOTES:
• After five minutes, the TV/VCR will automatically
switch to the Recording mode to prevent tape
damage.
• If “CLOSED CAPTION (ON)” is selected, the
On-Screen Display will appear for 5 seconds, then
disappear.
2)Stop the recording by pressing the STOP button
when recording is completed.
Plastic Tape
- 20 -
EN
9I03
T5505_7505UF(EN).QX33
04.4.12
10:01 AM
Page 21
OTR (One Touch Recording)
This function enables you to set the recording length
simply by pressing the REC/OTR button on the
TV/VCR.
1)Begin OTR by pressing the
REC/OTR button on the
TV/VCR repeatedly until the
desired recording length appears.
Recording stops when 0:00 is
reached.
NOTES:
• This function CANNOT be done from the remote
control.
• To stop the OTR operation, press the STOP button
on the TV/VCR or on the remote control.
• If the tape runs out before the end time, the
TV/VCR will switch to the Stop mode immediately, eject the tape and turn itself off.
• If you press the power button during OTR, the TV
monitor turns off. But the recording continues until
the selected length is reached.
OTR(2 : 30)
SP
Push(es)
1 push
2 pushes
3 pushes
4 pushes
17 pushes
Display
Recording length
(continuous recording)
0:30
30 minutes
1:00
60 minutes
1:30
90 minutes
8:00
480 minutes
TIMER RECORDING
You may set the TV/VCR to start and end a recording while you are away. You can set 8 programs to
record on specific days, daily or weekly within a 1
year period.
In the example below, the timer is being set to record:
DATE:
July 4th, 2004
SETTING TIME: from 7:30PM to 8:50PM
CHANNEL:
CH61
TAPE SPEED:
SP
Avoid overlap of programs ...
There is a chance that a program will not be recorded. When programs overlap:
• The program with the earliest start time will record
first.
• Once the earliest program finishes recording, the
overlapping programs will record in the order of
the program number.
• The illustration below demonstrates the sequence
of recording.
Recording Sequence
Program 1
10:00AM-11:00AM
Program 2
9:00AM-10:00AM
Program 3
9:30AM-12:00PM
9:00AM
10:00AM
11:00AM
12:00PM
*Recording period is SHADED
1
Select “TIMER PROGRAMMING”
Press the MENU button on the remote control.
Confirm “TIMER PROGRAMMING” is pointed to by pressing
the PLAY/K button.
Press the F.FWD/B button.
• If you have not yet set the clock,
“MANUAL CLOCK SET” appears. If so, follow
stops [3] to [8] on page 11. Then set the timer
recording.
–MENU–
B TIMER PROGRAMMING
PICTURE CONTROL
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
2
Select your desired program position (1~8)
Press the PLAY/K or STOP/L button to select the desired program
position.
Then, press the F.FWD/B button.
3
– TIMER PROGRAMMING –
CH DATE
B -
-
-/-/-/-/-/-/-/-/-
-
BEGIN END
-
-
-
-:-:-:-:-:-:-:-:-
-
-:- -:- -:- -:- -:- -:- -:- -:- -
-
-
-
-
Set the channel number
Press the PLAY/K or STOP/L button until the desired channel number appears.
(Example: CH61)
Then, press the F.FWD/B button.
Remember:
If your TV/VCR is connected to a cable or satellite
box, you must set the TV/VCR to channel 3 or 4 to
match the output channel of the box. Then, select
CH61 on the cable or satellite box.
– TIMER PROGRAMMING –
CH DATE
---B 61
-----
-/-/-/-/-/-/-/-/-
-
BEGIN END
-
-
-
-:-:-:-:-:-:-:-:-
-
-:- -:- -:- -:- -:- -:- -:- -:- -
Make sure ...
• If your TV/VCR is connected to a cable or satellite
box, you must set the TV/VCR to channel 3 or 4 to
match the output channel of the box.
• Clock is set to the correct time and date before setting the timer.
4 Select once, every day or
• TV/VCR power is turned on to program it.
weekly recording
• To insert a cassette tape with its erase prevention
For
once recording :
tab in place. (If necessary, rewind or fast forward
the tape to the point at which you want to begin
Press the PLAY/K (up) button
recording.)
until the desired date appears.
(Example: “7/04” for July 4th). Then, press the
• The channel you want to record is properly set in
advance.
- 21 EN
– TIMER PROGRAMMING –
CH DATE
- - -/- - - - - - -/- - - - - - -/- - - - B 61 7/04 SUN
- - -/- - - - - - -/- - - - - - -/- - - - - - -/- - - - -
BEGIN END
-:-:-:-:-:-:-:-:-
-
-:- -:- -:- -:- -:- -:- -:- -:- -
-
-
9I03
T5505_7505UF(EN).QX33
04.4.12
10:01 AM
Page 22
F.FWD/B button.
For every day recording : To record a TV program at
the same time on the same channel every day.
(Example: Monday through Sunday)
Press the STOP/L (down) button
until “EVRY DAY” appears.
Then, press the F.FWD/B button.
– TIMER PROGRAMMING –
CH DATE
BEGIN END
- - -/- - - - - -:- - -/- - - - - -:- - -/- - - - - -:B 61 EVRY DAY -:- - -/- - - - - -:- - -/- - - - - -:- - -/- - - - - -:- - -/- - - - - -:-
-
-:- -:- -:- -:- -:- -:- -:- -:- -
-
-
For weekly recording : To record a TV program at
the same time on the same channel every week.
(Example: every Monday)
Press the STOP/L (down) button
until “EVRY” and your desired
day of the week appear together.
Then, press the F.FWD/B button.
5
Set beginning hour
Press the PLAY/K or STOP/L button until the desired hour appears.
(Example: “ 7, PM” for 7:30PM)
Then, press the F.FWD/B button.
6
Set beginning minute
Press the PLAY/K or STOP/L button until the desired minute appears.
(Example: “30” for 7:30PM)
Then, press the F.FWD/B button.
7
Set end hour
Press the PLAY/K or STOP/L button until the desired hour appears.
(Example: “8, PM” for 8:50PM)
Then, press the F.FWD/B button.
8
Set end minute
Press the PLAY/K or STOP/L button until the desired minute appears.
(Example: “50” for 8:50PM)
Then, press the F.FWD/B button.
9
Set the tape speed
Press the PLAY/K or STOP/L button until the desired tape speed
appears. (Example: SP)
Then, press the F.FWD/B button.
10
Set the timer
Press the POWER button to set automatic timer
recording. The RECORD indicator lights up.
• You must turn off the TV/VCR to activate automatic timer recording.
If power is not turned off and you continue watching TV, “TIMER REC STANDBY” starts flashing
on the TV screen 2 minutes before the programmed
start time.
TIMER PROGRAM EXTENSION
– TIMER PROGRAMMING –
CH DATE
BEGIN END
- - -/- - - - - -:- - -/- - - - - -:- - -/- - - - - -:B 61 EVRY MON -:- - -/- - - - - -:- - -/- - - - - -:- - -/- - - - - -:- - -/- - - - - -:-
-
-:- -:- -:- -:- -:- -:- -:- -:- -
-
-
– TIMER PROGRAMMING –
CH DATE
BEGIN END
- - -/- - - - - -:- - - -/- - - - - -:- - - -/- - - - - -:- P
B 61 7/04 SUN 7:12 M
- - -/- - - - - -:- - - -/- - - - - -:- - - -/- - - - - -:- - - -/- - - - - -:- -
-:-:-:-:-:-:-:-:-
-
-
-
-
-
-:- - -:- - -:- - 8:30PM
-:
-:- - -:- - -:- - -
-
– TIMER PROGRAMMING –
CH DATE
BEGIN END
- - -/- - - - - -:- - - -/- - - - - -:- - - -/- - - - - -:- P
B 61 7/04 SUN 7:30 M
- - -/- - - - - -:- - - -/- - - - - -:- - - -/- - - - - -:- - - -/- - - - - -:- -
-:-:-:-:-:-:-:-:-
-
– TIMER PROGRAMMING –
CH DATE
BEGIN END
- - -/- - - - - -:- - - -/- - - - - -:- - - -/- - - - - -:- P
B 61 7/04 SUN 7:30 M
- - -/- - - - - -:- - - -/- - - - - -:- - - -/- - - - - -:- - - -/- - - - - -:- -
-
TO CORRECT A PROGRAM
• While setting a program; press the REW/s but•
– TIMER PROGRAMMING –
CH DATE
BEGIN END
- - -/- - - - - -:- - - -/- - - - - -:- - - -/- - - - - -:- P
B 61 7/04 SUN 7:30 M
- - -/- - - - - -:- - - -/- - - - - -:- - - -/- - - - - -:- - - -/- - - - - -:- -
To shift the time schedule of an automatic timer
recording.
1)Press the POWER button.
2)Repeat step [1] on page 21.
3)Press the RECORD button and select the desired
program using the PLAY/K or STOP/L button.
4)Press the RECORD button again.
Each additional push will shift forward the
begin/end time for recording by 10 minutes. When
the recording is already in progress, each additional
push will shift forward the end time only. If you
want to cancel while setting, press the
PAUSE/STILL button on the remote control. The
recording time returns to the original time.
NOTE: When you shift forward the time schedule
during recording, the recording speed will automatically be set to the SLP mode.
5)Press the F.FWD/B or REW/s button to exit the
setting menu. Then press the MENU button on the
remote control to return to original mode.
-:- - - -:- - - -:- - - 8:50PM- -:- - - -:- - - -:- - - -:- - - -
– TIMER PROGRAMMING –
CH DATE
- - -/- - - - - - -/- - - - - - -/- - - - B 61 7/04 SUN
- - -/- - - - - - -/- - - - - - -/- - - - - - -/- - - - -
BEGIN END
-:- -:- -:- 7:30PM
-:- -:- -:- -:- -
-:- - - -:- - - -:- - - 8:50PMSP
-:- - - -:- - - -:- - - -:- - - -
ton to go back one step and enter the correct numbers using the PLAY/K or STOP/L button.
After setting a program;
1)Press the POWER button.
2)Repeat steps [1] - [2] on page 21.
3)Press the F.FWD/B button (or press the REW/s
button to go back one step) until the part you
want to correct begins flashing, then make the
changes pressing the PLAY/K or STOP/L button.
4)Press the POWER button to set automatic timer
recording.
The program is now completed.
• To set another program, repeat steps [2] to [10].
• Press the MENU button on the remote control
to return to original mode.
- 22 -
EN
9I03
T5505_7505UF(EN).QX33
04.4.12
10:01 AM
Page 23
TO CANCEL AN AUTOMATIC TIMER
RECORDING
2
• After setting a program;
•
1)Press the POWER button.
2)Repeat steps [1] ~ [2] under TIMER RECORDING, page 21, and select a program you want to
cancel.
3)Press the T-PROG. CLEAR button.
4)Press the MENU button on the remote control to
return to TV mode.
While recording is in progress;
1)Press POWER button.
2)Press the STOP/EJECT button on the TV/VCR.
TO CHECK THE BEGIN/END TIME
1)Press the POWER button so that the REC indicator
goes off.
2)Press the MENU button on the remote control.
3)Confirm “TIMER PROGRAMMING” is pointed
to.
4)Press the F.FWD/B button. The details of programs appear on the TV screen.
5)Press the MENU button on the remote control to
return to TV mode.
HINTS FOR AUTOMATIC
TIMER RECORDING
• Make sure the channel you want to record is prop-
RENTAL
REPEAT PLAY
B AUTO RETURN
3
•
•
•
With this feature, after timer recording is finished,
the beginning of the recorded program(s) can be
searched for automatically.
1
Select “USER’S SET UP”
Press the MENU button on the
remote control.
Press the PLAY/K or STOP/L button to point to “USER’S SET UP”.
Then, press the F.FWD/B button.
Auto Return will begin
4
Watch the recorded program
Press the PLAY button.
TO CANCEL THE AUTO RETURN
MODE
Repeat steps [1] and [2], select [OFF] using the
F.FWD/B or REW/s button. Then, press the MENU
button on the remote control to return to TV mode.
If there is a power failure of any kind, the unit
will retain its memory for this feature.
WAKE UP TIMER
The Wake Up Timer function turns on the TV/VCR
without using the POWER button after a desired
period of time.
NOTES:
• Use the remote control for this procedure.
• Clock must be set to the correct time before setting
the timer.
• If you want to select [TAPE], you must insert a
cassette tape in the TV/VCR. The tape will start
playback automatically on your desired time.
1
AUTO RETURN
[OFF]
[OFF]
[ON]
When all the timer recordings are completed, the
TV/VCR will rewind to the beginning of the recorded
program(s).
NOTE:
• If you press the POWER button while tape is
rewinding, the Auto Return will stop.
erly set in advance.
•
•
– USER’S SET UP –
Press the PLAY/K or STOP/L button to point to “AUTO RETURN”.
Press the F.FWD/B or REW/s
button until [ON] appears. Then,
press the MENU button on the remote control to
return to TV mode.
• It is not necessary to press the RECORD button for
timer recording.
Recording begins automatically at the Start time.
If you are recording using a Timer mode, you may
not operate the unit manually.
The erase-prevention tab on the cassette must be in
place (or you must put tape over the hole).
If the erase-prevention tab is removed, the cassette
will be ejected when the POWER button is pressed
to off.
If the tape runs out before the end time, the
TV/VCR will switch to the Stop mode immediately, and the tape will be ejected.
Set “AUTO RETURN” to [ON]
Select “WAKE UP TIMER”
Press the WAKE-UP/SLEEP button
on the remote control once, and
confirm “ON/OFF” is pointed.
Press the F.FWD/B or REW/s
button until [ON] appears.
WAKE UP B ON/OFF
TIMER
TV/TAPE
TIME
[ON]
[TV]
[12:00AM]
–MENU–
TIMER PROGRAMMING
PICTURE CONTROL
SETTING CLOCK
CHANNEL SET UP
B USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
- 23 -
EN
9I03
T5505_7505UF(EN).QX33
2
04.4.12
10:01 AM
SLEEP TIMER
Select “TV” or “TAPE”
Press the PLAY/K or STOP/L button until it points to “TV/TAPE”.
Press the F.FWD/B or REW/s
button, and select [TV] or [TAPE].
3
Page 24
WAKE UP
ON/OFF
TIMER
B TV/TAPE
TIME
[ON]
[TV]
[12:00AM]
The Sleep Timer function turns off the TV/VCR
without using the POWER button after a desired
period of time.
NOTE:
• This function does not operate during Recording
mode.
Set wake up time
1
Press the PLAY/K or STOP/L button until it points to “TIME”.
Press the F.FWD/B or REW/s
button until your desired wake up
time appears.
Each additional push will increase (or decrease) the
time by 10 minutes.
WAKE UP
TIMER
ON/OFF
TV/TAPE
B TIME
Select “SLEEP TIMER”
Press the WAKE UP/SLEEP button on the remote
control until “SLEEP TIMER” appears.
[ON]
[TV]
[12:00AM]
2
Set sleep time
Press the MENU button on the remote control to
return to TV mode.
Press the PLAY/K, STOP/L,
F.FWD/B or REW/s button until
your desired sleep time appears.
Each additional push will increase
the time by 30 minutes up to 120 minutes.
Press the MENU button on the remote control to exit
the Sleep Timer setting.
TO CANCEL THE WAKE UP TIMER
TO CANCEL THE SLEEP TIMER
Press the WAKE-UP/SLEEP button on the remote
control once, and confirm “ON/OFF” is pointed.
Press the F.FWD/B or REW/s button until [OFF]
appears.
Press the WAKE UP/SLEEP button on the remote
control until “SLEEP TIMER” appears.
To view the time left for sleep timer, press the
WAKE-UP/SLEEP button twice, then press the
MENU button on the remote control to exit the sleep
timer setting.
SLEEP TIMER
4
Exit the Wake Up Timer setting
[2:00]
COPYING A VIDEO TAPE
You can make copies of video tapes made by friends
or relatives for your enjoyment.
WARNING: Unauthorized recordings of
copyrighted video tapes may be an
infringement of copyright laws.
Connect your TV/VCR and a Source (Playing) VCR
using the following diagram.
[TV/VCR]
[Ex: Source (playing)
VCR or camcorder]
Audio/Video
patch cord
(not supplied)
AUDIO
1)Insert a pre-recorded video cassette into the Source
(Playing) VCR or camcorder.
2)Insert a blank video cassette, or one you want to
record into the TV/VCR’s cassette compartment.
3)Press the SPEED button on remote control for the
TV/VCR to select the desired recording speed
(SP/SLP).
4)Press the CHANNEL K or L button on the
TV/VCR until “AUX” appears on the screen.
NOTE: “AUX” is found below the lowest numbered
memorized channel. (Example: CH2)
5)Press the RECORD button on the TV/VCR.
6)Begin playback of the tape in the source (Playing)
VCR or camcorder.
NOTE: For best results during copying, use the
TV/VCR’s front panel controls whenever possible.
The remote control might affect the source (Playing)
VCR’s playback operation.
7)To stop copying, press STOP/EJECT button on the
TV/VCR, then stop the tape on the source VCR or
camcorder.
OUT
VIDEO
- 24 -
EN
9I03
T5505_7505UF(EN).QX33
04.4.12
10:01 AM
Page 25
ON SCREEN DISPLAY
To check the Counter, Clock and Channel number on the TV screen, press the DISPLAY button on the remote
control. Each time you press the DISPLAY button on the remote control, the TV screen will change as follows:
WHEN THE CLOSED CAPTION MODE IS OFF:
• Counter mode: After 5 seconds, only
•
<Off mode>
<Counter mode>
the counter remains. To clear it, press
the DISPLAY button.
Clock mode: After 5 seconds, only
the clock and the channel number
remain. To clear them, press the DISPLAY button.
<Clock mode>
5:40PM
CH2
Press
once
Press
once
COUNT 0:12:34
Press once
WHEN THE CLOSED CAPTION MODE IS ON:
OFF mode
• The On Screen Display disappears after 5 seconds.
• This is true even if the MUTE button is pressed, or the
Clock/Counter mode
STOP
5:40 PM
CH2
PAUSE/STILL button is pressed while recording.
SP
COUNT 0:12:34
SPECIAL FEATURES
REAL TIME TAPE COUNTER
AUTO REWIND-EJECT
This shows the elapsed recording or playback time in
hours, minutes, and seconds. (The displayed time
will not change on a blank tape or blank portions on
the tape.)The “–” indication will appear when the
tape has rewound further than “0:00:00” on the tape
counter.
• When the end of a tape is reached during record-
•
•
ing, playback, or fast-forward, the tape will automatically rewind to the beginning. After rewinding
finishes, the TV/VCR will eject the tape and turn
itself to off.
This function is operative when Repeat Play is set
to the [OFF] position.
The tape will not auto-rewind during timer recording or One Touch Recording.
MAINTENANCE
CABINET CLEANING
• Wipe the front panel and other exterior surfaces of
•
the TV/VCR with a soft cloth immersed in lukewarm water and wrung dry.
Never use a solvent or alcohol. Do not spray insecticide liquid near the TV/VCR. Such chemicals
may cause damage and discoloration to the
exposed surfaces.
AUTO HEAD CLEANING
• Automatically cleans video heads as you insert or
•
remove a cassette, so you can see a clear picture.
Playback picture may become blurred or interrupted while the TV program reception is clear. Dirt
accumulated on the video heads after long periods
of use, or the usage of rental or worn tapes can
cause this problem.
If a streaky or snowy picture appears during play-
back, the video heads in your TV/VCR may need
to be cleaned.
1. Please visit your local Audio/Video store and purchase a good quality VHS Video Head Cleaner.
2. If a Video Head Cleaner does not solve the problem, please call our help line at 1-800-488-1222, to
locate an Authorized Service Center.
NOTES:
• Remember to read the instructions included with
the video head cleaner before use.
• Clean video heads only when problems occur.
SERVICING
• Should your TV/VCR become inoperative, do not
- 25 -
try to correct the problem by yourself. There are no
user-serviceable parts inside. Turn off, unplug the
power cord, and please call our help line at 1-800488-1222, to locate an Authorized Service Center.
EN
9I03
T5505_7505UF(EN).QX33
04.4.12
10:01 AM
Page 26
TROUBLESHOOTING GUIDE
If you have followed the instructions contained in this manual and have difficulty in operating your TV/VCR,
locate the PROBLEM in the left column below. Check the corresponding CORRECTIVE ACTION column to
remedy the problem.
PROBLEM
No power.
No picture and sound.
No picture or poor picture on
TV/VCR.
No sound or poor sound.
Timer recording is not possible.
Cannot go into Record mode.
Playback picture is partially noisy.
No picture but the audio is OK for
tape playback.
No operation by infrared Remote
Control.
Video or color fades in and out
when making a copy of a video tape.
Different color marks on screen.
CORRECTIVE ACTION
• Make sure the AC cord is connected to an AC outlet.
• Make sure the power is turned on.
• Make sure the AC cord is connected to an AC outlet.
• Check antenna connection.
• Program TV channels into TV/VCR.
• Adjust direction or replace antenna.
• Adjust picture controls.
• Adjust volume control on remote control or main unit.
• Press the MUTE button to restore sound.
• Make sure the timer recording is set correctly.
• Make sure the power is off.
• Make sure the TV/VCR clock is set correctly.
• Make sure the video tape has an erase-prevention tab in place. If the
• tab has been removed, please cover the open space with tape.
• Adjust tracking control for a better picture using the CHANNEL K
• or L button on the TV/VCR.
• Head cleaning may be necessary. Refer to “AUTO HEAD
• CLEANING” on page 25.
• Make sure the AC cord is connected to an AC outlet.
• Check batteries in remote control.
• You can not copy a copyrighted video tape. You are experiencing
• copy guard protection.
• Magnetism from nearby appliances or unshielded stereo speakers or
geomagnetism might affect the color of the TV picture. Refer to
“DEGAUSSING” on page 14.
CLOSED CAPTION PROBLEM
POSSIBLE REMEDY
My TV/VCR is showing captions
• You are watching a live broadcast and spelling errors made by the
that are misspelled.
• closed captioning production company may pass through uncorrected.
• A prerecorded program will not show any misspelled words because
• of the normal time available for editing the captions.
My TV/VCR will not show the text • Captions that are delayed a few seconds behind the actual dialogue
in its entirety or there is a delay of • are common for live broadcast. Most captioning production companies
what is being said.
• can display a dialogue to a maximum of 220 words per minute. If a
• dialogue exceeds that rate, selective editing is used to insure that the
• captions remain up-to-date with the current TV screen dialogue.
My captions are scrambled with
• Interference caused by building, power lines, thunderstorms, etc.
white boxes on the TV screen.
• may cause scrambled or incomplete captions to appear.
My program guide listed a TV show • Broadcasters may at times use a time compression process to speed
as being closed captioned but none • up the actual program so that additional advertising time can be
of the captions were displayed.
• given. Since the decoder cannot read the compressed information,
• captions will be lost.
My prerecorded video tape does not • The video tape was either an illegal copy or the tape duplicating
show any captions. The tape box
• company accidentally left out the captioning signals during the
mentions it being closed captioned. • copying process.
My TV screen shows a black box
• You are in the TEXT mode. Select CAPTION mode to CAPTION
on certain channels.
• [OFF].
- 26 -
EN
9I03
T5505_7505UF(EN).QX33
04.4.12
10:01 AM
Page 27
SPECIFICATIONS
GENERAL SPECIFICATIONS
ELECTRICAL SPECIFICATIONS
CRT :
Video input level :
Audio input level :
Video S/N ratio :
Audio S/N ratio :
13 or 19 inch in-line gun, 90˚
deflection tube
Television system :
NTSC-M
Closed caption system :§15.119/FCC
Video Heads :
Rotary four-head
Tape width :
1/2 inch
Tape speed
SP :
33.40mm/sec.
LP :
16.67mm/sec.
SLP :
11.12mm/sec.
Tuner channel
TV VHF Low :
#2~#6
TV VHF High :
#7~#13
TV UHF :
#14~#69
CATV
VHF :
5A
MID band :
A5~A1, A~I
SUPER band :
J~W
HYPER band :
W+1~W+84
FM:
88~108MHz (13” only)
Terminals
Antenna input :
VHF/UHF 75 ohms
unbalanced
Video input :
RCA connector [ 1
Audio input :
RCA connector [ 1
Earphone :
1/8” monaural (3.5 mm)
0.5~2.0Vp-p
-15dBs
More than 46dB
More than 43dB
OTHER SPECIFICATIONS
[ 13 inch model ]
Power requirement :
Power consumption :
Dimensions :
Weight :
[ 19 inch model ]
Power requirement :
Power consumption :
Dimensions :
Weight :
AC 120V/60Hz
60W
H:15-5/16” (389mm)
W:14-7/16” (367mm)
D:14-7/8” (377mm)
23.1 lbs (10.5kg)
AC 120V/60Hz
80W
H:19-7/16” (493mm)
W:19-5/16” (491mm)
D:18-11/16” (475mm)
43.0 lbs (19.5kg)
• Designs and specifications are subject to change
•
without notice and without our legal obligation.
If there is a discrepancy between languages, the
default language will be English.
CABLE CHANNEL DESIGNATIONS
If you subscribe to cable TV, the channels are displayed as 1-125. Cable companies often designate channels
with letters or letter-number combinations. Please check with your local cable company. The following is a
chart of common cable channel designations.
CATV channel
5A
2
3
4
5
6
7
8
9
10
11
12
13
A
B
TV Display
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
CATV channel
C
16
D
17
E
18
F
19
G
20
H
21
I
22
J
23
K
24
L
25
M
26
N
27
O
28
P
29
Q
30
TV Display
CATV channel
R
S
T
U
V
W
W+1
W+2
W+3
W+4
W+5
W+6
W+7
W+8
W+9
TV Display
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
CATV channel W+10
TV Display
46
CATV channel W+25
TV Display
61
CATV channel W+40
TV Display
76
CATV channel W+55
TV Display
91
CATV channel W+65
TV Display
106
CATV channel W+80
TV Display
121
W+11 W+12 W+13 W+14 W+15 W+16 W+17 W+18 W+19 W+20 W+21 W+22 W+23 W+24
47
48
49
50
51
52
53
54
55
56
57
58
59
60
W+26 W+27 W+28 W+29 W+30 W+31 W+32 W+33 W+34 W+35 W+36 W+37 W+38 W+39
62
63
64
65
66
67
68
69
70
71
72
73
74
75
W+41 W+42 W+43 W+44 W+45 W+46 W+47 W+48 W+49 W+50 W+51 W+52 W+53 W+54
77
78
79
W+56 W+57 W+58
92
93
94
80
81
82
83
84
85
86
A-5
A-4
A-3
A-2
A-1
W+59 W+60 W+61 W+62 W+63 W+64
95
96
97
98
99
100
101
87
102
88
103
89
104
90
105
W+66 W+67 W+68 W+69 W+70 W+71 W+72 W+73 W+74 W+75 W+76 W+77 W+78 W+79
107
108
109
110
111
112
113
114
115
116
117
118
119
120
W+81 W+82 W+83 W+84
122
123
124
125
- 27 -
EN
9I03
T5505_7505UF(ES).QX33
04.4.12
10:03 AM
Page 28
CONTROLES DE OPERACIÓN Y SUS FUNCIONES
Este manual sirve para los modelos de 13" y 19". A excepción de la apariencia, la operación de los dos modelos es exactamente la misma. En este manual se muestra el modelo de 13".
NOTA:
No recomendamos utilizar mandos a distancia universales. No todas las funciones pueden ser controladas mediante un
mando a distancia universal. Si decide utilizar un mando a distancia universal con esta unidad, tenga en cuenta que con el
número de código dado tal vez no se pueda controlar la unidad. En este caso, póngase en contacto con el fabricante del
mando a distancia universal.
- PANEL DELANTERO -
4 Botones de volumen (VOLUME X/ Y)–
Ajustan el nivel del volumen.
5 Botones de canales (CHANNEL K/ L)–
Púlselos para seleccionar los canales deseados para
ver o grabar.
Se puede mostrar el menú principal en la pantalla del
televisor pulsando repetidamente este botón del televisor/videograbadora.
Función de seguimiento– Pulse los botones
para minimizar el ruido de vídeo (líneas o puntos en
la pantalla) durante la reproducción.
- CONTROL REMOTO -
25
WAKE-UP
/SLEEP
POWER
3
15
16
17
8
CHANNEL
RETURN
1
2
3
4
5
6
7
8
9
0
+100
MENU
DISPLAY
MUTE
CHANNEL
19
20
VOLUME
PLAY
REW
F.FWD
26
24
5
4
23
9
10
STOP
7
11
18
TV/FM
RECORD
T-PROG.
CLEAR
COUNTER
RESET
SPEED
PAUSE/STILL
GAME
SLOW
22
21
1 Toma de entrada de vídeo (VIDEO)–
Conéctela a la toma de salida de vídeo de su
videocámara u otra videograbadora.
2 Toma de entrada de audio (AUDIO)–
Conéctela a la toma de salida de audio de su equipo
de audio, videocámara u otra videograbadora.
3 Botón de la alimentación (POWER)– Púlselo
para encender y apagar el televisor/videograbadora.
Púlselo para activar la grabación con temporizador.
- 28 -
6 Ventanilla sensora del mando a distancia–
Recibe las señales infrarrojas procedentes del
mando a distancia.
7 Botón L–
• Púlselo para seleccionar los modos de ajuste
desde el menúde la pantalla.
• Púlselo para introducir dígitos cuando establezca un programa.
(Por ejemplo: Para ajustar el reloj o establecer un
programa de temporizador)
[ Televisor/videograbadora ]
Botón de parada/expulsión (STOP/EJECT)–
Púlselo para detener la cinta. Púlselo en el modo
de parada para expulsar la cinta del
televisor/videograbadora.
[ Control remoto ]
Botón de parada (STOP)– Púlselo para detener la cinta.
8 Botón de rebobinado (REW)– Púlselo para
rebobinar la cinta, o para ver la imagen en retroceso
rápido durante el modo de reproducción. (Búsqueda
con rebobinado)
Botón s–
• Púlselo para seleccionar un modo desde un menú
particular.
(Por ejemplo: IDIOMA o ADJUST DE USER)
ES
0I29
T5505_7505UF(ES).QX33
04.4.12
10:03 AM
Page 29
- PANEL TRASERO -
9 Botón de reproducción (PLAY)– Púlselo para
iniciar la reproducción.
Botón K–
• Púlselo para seleccionar los modos de ajuste
desde el menú de la pantalla.
• Púlselo para introducir dígitos cuando establezca
un programa.
(Por ejemplo: Para ajustar el reloj o establecer un
programa de temporizador)
10 Botón de avance rápido (F.FWD)– Púlselo
para avanzar rápidamente la cinta, o para ver la
imagen en avance rápido durante el modo de reproducción. (Búsqueda con avance rápido)
Botón B–
• Cuando establezca un programa (por ejemplo: para
ajustar el reloj o para establecer un programa de
temporizador), púlselo para determinar su elección
y vaya al paso siguiente que quiera introducir.
• Púlselo para determinar los modos de ajuste
desde el menúde la pantalla.
• Púlselo para seleccionar un modo desde un
menúparticular.
(Por ejemplo: IDIOMA o ADJUST DE USER)
11 Botón de grabación (REC)– Púlselo para iniciar la grabación manual.
Botón de grabación de un toque (OTR)–
Activa la grabación de un toque. (Sólo en el televisor/videograbadora)
12 Indicador de grabación (RECORD)– Parpadea
durante la grabación.
Se enciende en el modo de espera de la grabación
con temporizador.
13 Toma de auriculares (EARPHONE)– Para
conectar los auriculares (no suministrados) y
escuchar en privado. La toma es mono y tiene un
tamaño de 1/8”(3.5 mm).
14 Compartimiento del videocasete
15 Botones numerados– Púlselos para seleccionar
los canales deseados para ver o grabar. Para seleccionar canales del 1 al 9, pulse primero el botón 0 y
luego el botón 1 a 9.
Botón +100– Cuando seleccione canales de televisión por cable cuyo número sea superior al 99,
pulse primero este botón, y luego pulse los dos últimos dígitos. (Para seleccionar el canal 125, pulse
primero el botón “+100” y luego el “2” y el “5”.)
16 Botón de menú (MENU)– Púlselo para visualizar el menúprincipal en la pantalla del televisor.
17 Botón del visualizador (DISPLAY)– Visualiza
el contador o el número del canal actual y la hora
actual en la pantalla del televisor.
18 Botón de velocidad de cinta (SPEED)–
Púlselo para elegir la velocidad de grabación deseada: SP/SLP.
19 Botón T-PROG. CLEAR– Púlselo para cancelar
un programa de temporizador.
Botón de reposición del contador
(COUNTER RESET)– Púlselo para reponer el
contador a 0:00:00.
20 Botón de juego (GAME)– Establece el modo del
juego y el modo de entrada externa al mismo tiempo.
21 Botón de cámera lenta (SLOW)– Pulselo para
activar la reproducción a cámera lenta.
22 Botón de pausa/imagen fija (PAUSE/STILL)–
Púlselo para detener temporalmente la cinta durante
la grabación o para ver una imagen fija durante la
reproducción.
23 Botón de silenciamiento (MUTE)– Silencia el
sonido. Púlselo de nuevo para recuperar el sonido.
24 Botón de retorno de canal (CHANNEL
RETURN)– Púlselo para volver al canal anterior.
Por ejemplo, pulsando una vez este botón, la visualización del canal cambiará de 3 (canal actual) a 10
(canal anterior), y al pulsarlo por segunda vez, el
canal cambiará del 10 al 3.
25 Botón del temporizador despertador/para
dormir (WAKE-UP/SLEEP)– Ajusta el temporizador para despertarse/dormir.
26 (13” model) Botón de televisor/modulación
de frecuen-cia (TV/FM) – Establece el modo
FM.
(19” model) Botón de explusión (EJECT)–
Púlselo para expulsar la cinta del
televisor/videograbadora.
27 Terminal de antena (ANT.)– Para conectar una
antena o sistema de televisión por cable.
28 Cordón de alimentación– Conéctelo a la toma
de CA estándar (120V/60Hz).
- 29 -
ES
0I29
T5505_7505UF(ES).QX33
04.4.12
10:03 AM
Page 30
CONEXIONES DE ANTENA/CABLE
Caja de CATV
o caja de emisiones vía satélite
(no incluído)
OUT
Desde el cable coaxial o
caja de emisiones vía
satélite de 75 ohm del
sistema de Cable
Antena de varilla UHF/VHF
(incluído para solamente 13”)
Antena combinada de
VHF/UHF
(no incluído)
IN
Antena VHF
(no incluído)
Desde el
sistema de Cable
Antena UHF
(no incluído)
o
ANT.
o
Cable coaxial
de 75 ohm (no incluído)
ANT.
o
o
MODO DE ENTRADA EXTERNA
2
Cuando utilice una señal de entrada externa (otra
videograbadora o una videocámara), conecte los cables
de salida de audio/vídeo del equipo de reproducción a
las tomas AUDIO IN/VIDEO IN de su
televisor/videograbadora. Y luego pulse el botón
CHANNEL K o L hasta que “AUX” aparezca en la
pantalla.
Usted puede programar el temporizador para que explore
todos los canales que puedan recibirse en su zona.
Enchufe el cordón de alimentación del
televisor/videograbadora en una toma de
CA estándar.
NOTA:
• Si aparecen algunas cifras en la esquina
de la pantalla, pulse el botón POWER sin desenchufar el cordón de alimentación.
Seleccione “LANGUAGE”
3
–MENU–
TIMER PROGRAMMING
PICTURE CONTROL
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
B LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
Seleccione “ENGLISH”, “ESPAÑOL” o “FRANÇAIS”
Seleccione “ENGLISH”, “ESPAÑOL” o
“FRANÇAIS” con el botón F.FWD/B y pulse el
botón REW/s en el mando a distancia.
4
Enchufe el cordón de alimentación
del televisor/videograbadora
Cable bifilar plano
Pulse el botón MENU en el mando
a distancia.
Pulse el botón PLAY/K o STOP/L
para señalar “LANGUAGE”.
SELECCION DE IDIOMA
1
Combinador de
VHF/UHF
(no incluído)
Salga del modo de idioma
Pulse el botón MENU en el mando a distancia para
volver al modo del televisor.
NOTA: Si, por alguna razón, el menú está en español
o francés, pulse el botón MENU en el mando a distancia, pulse el botón PLAY/K para señalar el
“IDIOMA (ESPAÑOL)” o “LANGAGE
(FRANÇAIS)”, a continuación, pulse el botón
F.FWD/B y pulse el botón MENU en el mando a
distancia.
Asegúrese de que ...
• Pulse el botón POWER para encender el televisor/videograbadora.
NOTA: Esta función afecta sólo el idioma en el
menú de la pantalla y no la fuente de audio.
- 30 -
ES
0I29
T5505_7505UF(ES).QX33
04.4.12
10:03 AM
Page 31
AJUSTE DE CANAL
AJUSTE DEL RELOJ
Puede programar el sintonizador para buscar todos
los canales que recibe en su localidad.
NOTA: El canal preparado NO es necesario cuando
esté conectado a una caja de cable o caja de satélite.
Sólo tiene que seleccionar con el selector de canal
del televisor/videograbadora al canal de salida de la
caja de cabe o caja de satélite (por ejemplo el canal
CH3). Seleccione el canal a ver en la caja de cable o
caja de satélite.
Asegúrese de que ...
• Pulse el botón POWER para encender el televisor/videograbadora.
1
Seleccione “AJUSTE DE CANAL”
Pulse el botón MENU en el mando
a distancia.
Pulse el botón PLAY/K o el botón
STOP/L para señalar “AJUSTE DE
CANAL”.
A continuación, pulse el botón
F.FWD/B.
2
–MENU–
COMO PROGRAMAR
CONTROL DE IMAGEN
AJUSTE RELOJ
B AJUSTE DE CANAL
AJUSTE DE USER
AJUSTE DE V-CHIP
IDIOMA [ESPAÑOL]`
TITULO [OFF]
RETORNO A CERO
BUSQUEDA DE HORA
BUSCA HACIA INDICE
Empiece el prefijado automático
Pulse el botón PLAY/K o STOP/L
para señalar “AUTOPROGRAMACION DE CA”.
A continuación, pulse el botón
F.FWD/B.
El sintonizador busca y memoriza todos los canales
activos en su localidad.
– AJUSTE DE CANAL –
AGREGAR/BORRAR (CATV)
B AUTOPROGRAMACION DE CA.
3
Cerciórese...
• La alimentación del televisor/videograbadora
deberá estar conectada.
En el ejemplo de abajo, el reloj va a ajustarse así:
FECHA: 6 de mayo de 2004
HORA: 5:40 PM
1) Pulse el botón MENU en el mando a distancia.
Pulse el botón PLAY/K o STOP/L para indicar
“AJUSTE RELOJ”.
Luego, pulse el botón F.FWD/B.
2) Pulse el botón PLAY/K o STOP/L para indicar
“AJUSTE MANUAL RELOJ”.
Luego, pulse el botón F.FWD/B.
3) Pulse el botón PLAY/K o STOP/L hasta que
aparezca el mes deseado. (Ejemplo: Mayo - 05)
Luego, pulse el botón F.FWD/B.
4) Pulse el botón PLAY/K o STOP/L hasta que
aparezca el día del mes deseado. (Ejemplo: 6 - 06)
Luego, pulse el botón F.FWD/B.
5) Pulse el botón PLAY/K o STOP/L hasta que
aparezca el año deseado. (Ejemplo: 2004)
Luego, pulse el botón F.FWD/B.
6) Pulse el botón PLAY/K o STOP/L hasta que
aparezca la hora deseada. (Ejemplo: 5, PM)
Luego, pulse el botón F.FWD/B.
7) Pulse el botón PLAY/K o STOP/L hasta que
aparezca el minuto deseado. (Ejemplo: 40)
8) Pulse el botón MENU en el mando a distancia.
Aunque los segundos no se visualizan, éstos
empiezan a contar desde 00 cuando se pulsa
MENU en el mando a distancia. Utilice esta función para sincronizar el reloj con la hora correcta.
Después de buscar
El sintonizador se detiene en el canal memorizado
más bajo.
• Cuando se activa AUTOPROGRAMACION DE
CA, donde no hay entrada de señal del televisor,
aparecerá “NO HAY SEÑAL DE TV” en la pantalla después de terminar la búsqueda de canales.
• El televisor/videograbadora puede reconocer los
canales de TV para que sean canales de TV de
antena de cable con las condiciones de recepción.
En este caso, pruebe nuevamente con el prefijado
automático en las condiciones de recepción fina.
- 31 -
ES
T5505_7505UF(BCV).QX33
04.4.12
10:04 AM
Page 48
Get it fixed, at your home or ours!
Your Home
For repair- in your home -of all major brand appliances,
lawn and garden equipment, or heating and cooling systems,
no matter who made it, no matter who sold it!
For the replacement parts, accessories and
owner's manuals that you need to do-it-yourself.
For Sears professional installation of home appliances
and items like garage door openers and water heaters.
1-800-4-MY-HOME R
(1-800-469-4663)
Call anytime, day or night (U.S.A. and Canada)
www.sears.com
www.sears.ca
Our Home
For repair of carry-in items like vacuums, lawn equipment,
and electronics, call or go on-line for the location of your nearest
Sears Parts & Repair Center.
1-800-488-1222
Call anytime, day or night (U.S.A. only)
www.sears.com
To purchase a protection agreement on a product serviced by Sears:
1-800-827-6655 (U.S.A.)
Para pedir servicio de reparación
a domicilio, y para ordenar piezas:
Au Canada pour service en français:
1-888-SU-HOGARSM
(1-800-533-6937)
www.sears.ca
(1-888-784-6427)
R
R
1-800-361-6665 (Canada)
1-800-LE-FOYERMC
Registered Trademark / TM Trademark / SM Service Mark of Sears, Roebuck and Co.
Marca Registrada / TM Marca de Fábrica / SM Marca de Servicio de Sears, Roebuck and Co.
Marque de commerce / MD Marque déposée de Sears, Roebuck and Co.
MC
© Sears, Roebuck and Co.
LIMITED 90 DAY WARRANTY FOR 13 INCH MODEL
If this (product) experiences any failure due to a defect in material or workmanship within 90 days from the date of
purchase, return it to your nearest Sears store, and it will be replaced free of charge.
This warranty applies only if this (product) is used for private household purposes.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
FULL 90 DAY WARRANTY FOR 19 INCH MODEL
For 90 days from the date of purchase, Sears will repair any defect in material or workmanship in this TV/VCR
combination, free of charge. For one year from the date of purchase, Sears will supply, at no charge, replacement
for defective parts.
Two (2) years for Picture Tube. Certain parts are excluded from this warranty.
The above warranty coverage applies only to TV/VCR combination which are used for private household purposes.
TO OBTAIN WARRANTY SERVICE, SIMPLY RETURN THE TV/VCR COMBINATION TO THE NEAREST SEARS
SERVICE CENTER IN THE UNITED STATES.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Sears Roebuck and Co., Dept. 817WA Hoffman Estates, IL 60179
For the location of a Sears Service Center in your area : 1-800-488-1222
Printed in Malaysia
0EMN02407
T5505UF/T7505UF ★★★★★
Download PDF

advertising