Bosch Appliances 8555 Home Security System User Manual

LCD TV PLASMA TV
OWNER’S MANUAL
LCD TV MODELS
32LC5DC
32LC50CS
32LC5DCS
32LC50CB
32LX50C
32LC5DCB
37LC5DC
32LX50CS
37LC50C
37LC5DCB
37LC5DC1
37LC50CB
42LC5DC
42LB50C
42LC50C
32LX5DC
32LX5DCS
32LG500H
37LG500H
42LB5DC
42LG500H
32LC50C
PLASMA TV MODEL
42PX8DC
42PG65C
42PG60C
Please read this manual carefully before operating
your set.
Retain it for future reference.
Record model number and serial number of the set.
See the label attached on the back cover and quote
this information to your dealer when you require
service.
www.lgcommercial.com
WARNING / CAUTION
WARNING / CAUTION
To prevent fire or shock hazards, do not expose
this product to rain or moisture.
TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK). NO
USER SERVICEABLE PARTS INSIDE. REFER TO
QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead
symbol, within an equilateral triangle,
is intended to alert the user to the
presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to
the presence of important operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
WARNING/CAUTION
TO REDUCE THE RISK OF FIRE AND ELECTRIC
SHOCK, DO NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE.
NOTE TO CABLE/TV INSTALLER
This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the National
Electric Code (U.S.A.). The code provides guidelines for
proper grounding and, in particular, specifies that the
cable ground shall be connected to the grounding system of the building, as close to the point of the cable
entry as practical.
A
FCC NOTICE
Class B digital device
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However,
there is no guarantee that interference will not
occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to
try to correct the interference by one or more of
the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment
and receiver.
- Connect the equipment to an outlet on a circuit
different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV
technician for help.
Any changes or modifications not expressly
approved by the party responsible for compliance
could void the user’s authority to operate the
equipment.
CAUTION
Do not attempt to modify this product in any way
without written authorization from LG Electronics.
Unauthorized modification could void the user’s
authority to operate this product
SAFETY INSTRUCTION
IMPORTANT SAFETY INSTRUCTIONS
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
1
2
6
Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
7
Only use attachments/accessories specified by
the manufacturer.
8
Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use
caution when moving the cart/apparatus
combination to avoid injury from tip-over.
9
Unplug this apparatus during lighting storms or
when unused for long periods of time.
10
Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
Do not use this apparatus near water.
Clean only with dry cloth.
3
Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
4
Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers)that produce heat.
5
Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has
two blades with one wider than the other. A
grounding type plug has two blades and a third
grounding prong, The wide blade or the third
prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
1
SAFETY INSTRUCTION
2
11
Never touch this apparatus or antenna during a
thunder or lighting storm.
12
When mounting a TV on the wall, make sure not to
install the TV by the hanging power and signal
cables on the back of the TV.
13
Do not allow an impact shock or any objects to fall
into the product, and do not drop onto the screen
with something.
14
CAUTION concerning the Power Cord :
It is recommend that appliances be placed upon a
dedicated circuit; that is, a single outlet circuit which
powers only that appliance and has no additional
outlets or branch circuits. Check the specification
page of this owner's manual to be certain.
Do not connect too many appliances to the same
AC power outlet as this could result in fire or electric shock.
Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords,
frayed power cords, or damaged or cracked wire
insulation are dangerous. Any of these conditions
could result in electric shock or fire. Periodically
examine the cord of your appliance, and if its
appearance indicates damage or deterioration,
unplug it, discontinue use of the appliance, and
have the cord replaced with an exact replacement
part by an authorized servicer. Protect the power
cord from physical or mechanical abuse, such as
being twisted, kinked, pinched, closed in a door, or
walked upon. Pay particular attention to plugs, wall
outlets, and the point where the cord exits the
appliance.
Do not make the TV with the power cord plugged
in. Do not use a damaged or loose power cord. Be
sure do grasp the plug when unplugging the power
cord. Do not pull on the power cord to unplug the
TV.
15
WARNING - To reduce the risk of fire or electrical
shock, do not expose this product to rain, moisture
or other liquids. Do not touch the TV with wet
hands. Do not install this product near flammable
objects such as gasoline or candles or expose the
TV to direct air conditioning.
16
Do not expose to dripping or splashing and do not
place objects filled with liquids, such as vases, cups,
etc. on or over the apparatus (e.g. on shelves above
the unit).
17
GROUNDING
Ensure that you connect the earth ground wire to
prevent possible electric shock. (i.e. a TV with a
three-prong grounded AC plug must be connected
to a three-prong grouned AC outlet) If grounding
methods are not possible, have a qualified electrician install a separate circuit breaker.
Do not try to ground the unit by connecting it to
telephone wires, lightening rods, or gas pipes.
Power
Supply
Short-circuit
Breaker
18
DISCONNECTING DEVICE FROM MAINS
Mains plug is the disconnecting device. The plug
must remain readily operable.
19
Keep the product away from direct sunlight.
20
ANTENNAS
Outdoor antenna grounding
If an outdoor antenna is installed, follow the precautions below. An outdoor antenna system should not
be located in the vicinity of overhead power lines or
other electric light or power circuits, or where it can
come in contact with such power lines or circuits as
death or serious injury can occur.
Be sure the antenna system is grounded so as to provide some protection against voltage surges and
built-up static charges.
Section 810 of the National Electrical Code (NEC) in
the U.S.A. provides information with respect to proper grounding of the mast and supporting structure,
grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of
antenna discharge unit, connection to grounding
electrodes and requirements for the grounding electrode.
Antenna grounding according to the
National Electrical Code, ANSI/NFPA 70
Ground Clamp
Cleaning
When cleaning, unplug the power cord and scrub
gently with a soft cloth to prevent scratching. Do not
spray water or other liquids directly on the TV as
electric shock may occur. Do not clean with chemicals such as alcohol, thinners or benzene.
22
Moving
Make sure the product is turned off, unplugged
and all cables have been removed. It may take 2 or
more people to carry larger TVs. Do not press
against or put stress on the front panel of the TV.
23
Ventilation
Install your TV where there is proper ventilation. Do
not install in a confined space such as a bookcase.
Do not cover the product with cloth or other materials (e.g.) plastic while plugged in. Do not install in
excessively dusty places.
24
If you smell smoke or other odors coming from the
TV or hear strange sounds, unplug the power cord
contact an authorized service center.
25
Do not press strongly upon the panel with a hand or
sharp object such as nail, pencil or pen, or make a
scratch on it.
Antenna Lead in Wire
Antenna Discharge Unit
(NEC Section 810-20)
Electric Service
Equipment
21
Grounding Conductors
(NEC Section 810-21)
Ground Clamps
Power Service Grounding
Electrode System (NEC
Art 250, Part H)
NEC: National Electrical Code
3
CONTENTS
WARNING / CAUTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . A
SAFETY INSTRUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
FEATURE OF THIS TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
PREPARATION
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Front Panel Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Back Panel Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Back Cover for Wire Arrangement . . . . . . . . . . . . . . . . . . . . . 12
Stand Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Attaching the TV to a Wall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Swivel Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Attaching the TV to a Desk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
VESA Wall Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Desktop Pedestal Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Antenna or Cable Connection . . . . . . . . . . . . . . . . . . . . . . . . . . 20
EXTERNAL EQUIPMENT SETUP
HD Receiver Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
DVD Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
VCR Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Other A/V Source Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Digital Audio Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
PC Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
WATCHING TV / CHANNEL CONTROL
Remote Control Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Turning On TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Channel Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Volume Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
On-Screen Menus Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Channel Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
- Auto Scan (EZ Scan) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
- Add / Delete Channel (Manual Scan) . . . . . . . . . 37
- Channel Editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
DTV Signal Strength . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Channel Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
PICTURE CONTROL
Watching DW (Double Window) . . . . . . . . . . . . . . . . . . . . . . . 41
Picture Size (Aspect Ratio) Control . . . . . . . . . . . . . . . . . . 43
Preset Picture Settings
- EZ Picture - Preset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
- Color Tone - Preset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Manual Picture Adjustment
- EZ Picture - User Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
- Color Tone - User Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
XD - Picture Improvement Technology . . . . . . . . . . . . . 49
Advanced - Cinema Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Advanced - Black (Darkness) Level . . . . . . . . . . . . . . . . . . . 51
4
Picture Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Low-Power Picture Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Image Sticking Minimization( ISM) Method . . . . . . . . . . . . . 53
SOUND & LANGUAGE CONTROL
Auto Volume Leveler (EZ SoundRite) . . . . . . . . . . . . . . . . 54
Preset Sound Setting (EZ Sound) . . . . . . . . . . . . . . . . . . . . . 55
Sound Setting Adjustment - User Mode . . . . . . . . . . . 56
Balance Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
TV Speakers On/Off Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Stereo/SAP Broadcasts Setup . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Audio Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
On-Screen Menus Language Selection . . . . . . . . . . . . . . 61
Caption/Text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
- Analog Broadcasting System Captions . . . . . . . 62
- Digital Broadcasting System Captions . . . . . . . . 63
Caption Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
TIME SETTING
Clock Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
- Auto Clock Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
- Manual Clock Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Auto On/Off Timer Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Auto Shut-off Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Sleep Timer Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
SCREEN ADJUSTMENT
Auto Configure (RGB(PC) Mode only) . . . . . . . . . . . . . 70
Manual Configure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Selecting XGA Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Initializing (Reset to Original Factory Settings) . 73
PARENTAL CONTROL / RATINGS
Set Password & Lock System . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
- Setting up Your Password . . . . . . . . . . . . . . . . . . . . . . . . . 74
- Set Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
- Lock System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Channel Blocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
External Input Blocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Movie & TV Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
- Movie Rating (MPAA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
- Downloadable Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
- TV Rating Children & General . . . . . . . . . . . . . . . . . . . 78
- TV Rating English & French . . . . . . . . . . . . . . . . . . . . . . . 79
APPENDIX
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Programming the Remote Control . . . . . . . . . . . . . . . . . . . . 84
Set ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
IR Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
FEATURES OF THIS TV
On Disposal
a. The fluorescent lamp used in this product contains a small amount of mercury.
b. Do not dispose of this product with general
household waste.
c. Disposal of this product must be carried out in
accordance to the regulations of your local
authority.
FOR LCD TV
PREPARATION
If the TV feels cold to the touch, there may be a
small “flicker” when it is turned on. This is normal,
there is nothing wrong with TV.
Some minute dot defects may be visible on the
screen, appearing as tiny red, green, or blue spots.
However, they have no adverse effect on the monitor's performance.
Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so
may produce some temporary distortion effects on
the screen.
PREPARATION
ACCESSORIES
Ensure that the following accessories are included with your product. If an accessory is missing, please contact the dealer where you purchased the product.
User must use shielded signal interface cables (D-sub 15 pin cable) with ferrite cores to maintain standard
compliance for the product.
PU
TV T
INP
MU
PIP
EZ
LT
UT
PO
WE
R
MO
TV
I
DE
DV
TV
PIP
PIC
CH PO
VC
STEZ SOU - PIP W
R
B ND
CH ER
RA
+ PIP
TIO
SW
INPUDV
AP
T D
INF
CC
VCO
INP
D
R
UT
INP
TV
CC
XIT
INP
ME
NU
EN RA
TE TIO
R
SA
RE
TURN ENTE
R
ME
NU
MU
P
LT
PIC
TIM
IT
PIP
CH
-
PIP
PIP
SA
P
SWA
CD Manual
PIP
INPU
RA
TIO
SA
EN
TER
VO
L
P
TIM
ER
CH
MU
TE
PAG
1
E
1.5V 1.5V
2
4
CH
+
DE
ME
NU
or
FLASHB
K
P
http://www.lgusa.com
www.lg.ca
P
A
G
E
9
PIP
Owner’s Manual,
Setup & Operation Guide
for Commercial Mode
3
6
0
Copyright© 2007 LGE,
All Rights Reserved.
CHE
TE
MO
VC
R
PIP
CH
+ PIP
SW
INPU
AP
T
INF
O
CC
EX
PAG
MU
2
5
8
R
TV
-
ER
CH
1
4
7
Owner's Manual
PO
WE
D
CH
ND
i
LCD TV PLASMA TV
UT
DV
PIP
EZ SOU
INFO
VO
L
UT
I
PIP
EZ
3
5
7
6
8
T
9
0
FLAS
BACK H
Remote Control,
Batteries
Power Cord
* Slightly wipe stained spot on the exterior only
with the polishing cloth for the product exterior if there is stain or fingerprint on surface of
the exterior.
Polishing Cloth
This feature is not available
for all models.
* Do not wipe roughly when removing stain.
Please be cautions of that excessive pressure
may cause scratch or discoloration.
5
PREPARATION
LCD TV model only
Option Extras
x2
M4xL22
Torx plus
Star head screw
(Refer to p.7, 15)
Protective Bracket and Bolt for
Power Cord
PREPARATION
(This feature is not available for all models.)
D-sub 15 pin Cable
(Refer to P.12-13, 15)
Only 32/37/42LC5DC*, 32/37/42LC50C*, 42LB5DC, 42LB50C models
Cable Holder
1-Bolt for fixing the
Cable Management
Cable Holder
(Refer to p.12) (Refer to p.12-13)
(Refer to p.12-13)
4-Bolts for stand
assembly
(Refer to p.16)
Only 32/37LC5DC*,
32/37LC50C* models
Only 32/37/42LG500H models
x4
or
x4
Bolts for stand assembly Screw for stand fixing Protection Cover
(Refer to P.15)
(Refer to P.19)
Cable Holder
Plasma TV models only
75 ohm Round Cable
(Except 42PG60C/65C)
D-sub 15 Pin Cable
(Except 42PG60C/65C)
Only 42PG65C model
x4
Cable Management Clip
6
Bolts for stand
assembly
(Refer to P.14)
Cable Holder
(Except 42PX8DC)
Plug in type
holder
FRONT PANEL CONTROLS
■
Here shown may be somewhat different from your TV.
32/37/42LC5DC*,32/37/42LC50C*, 42LB5DC, 42LB50C
PREPARATION
CH
CHANNEL Buttons
VOL
VOLUME Buttons
ENTER
ENTER Button
MENU
MENU Button
INPUT
INPUT Button
POWER Button
Remote Control Sensor
Power/Standby Indicator
Illuminates red when the TV is in standby mode.
Illuminates green when the TV is switched on.
x4
Tighten the stand with the
four screws (provided as parts
of the TV).
or
x2
Tighten the two of these four screws and
x 2 the two Torx plus star head screws (provided as parts of the TV) to secure the TV.
Tighten the two Torx plus star head screws
with a star head driver bit (not provided
as parts of the TV).
7
PREPARATION
32LX5DC*, 32LX50C*
PREPARATION
Remote Control Sensor
Power/Standby
Indicator
Illuminates red when the
TV is in standby mode.
Illuminates green when
the TV is switched on.
CH
VOL
ENTER
MENU
INPUT
ON/OFF
ON/OFF Button
INPUT Button
MENU Button
ENTER Button
VOLUME Buttons
CHANNEL Buttons
32/37/42LG500H
CH
Intelligent Sensor
Adjusts picture according to the surrounding
conditions
Power/Standby Indicator
Illuminates red in standby mode.
Illuminates blue when the set is switched on.
VOL
CHANNEL
Buttons
VOLUME
Buttons
ENTER
ENTER Button
MENU
MENU Button
INPUT
INPUT Button
Remote Control Sensor
POWER Button
8
42PX8DC
INPUT
ENTER
PREPARATION
This TV’s stand is sold, separately.
INPUT
Remote Control Sensor
Power/Standby
Indicator
Illuminates red when the
TV is in standby mode.
Illuminates green when
the TV is switched on.
MENU
ENTER
VOL
CH
POWER Button
INPUT Button
MENU Button
ENTER Button
VOLUME Buttons
CHANNEL Buttons
42PG60C, 42PG65C
Remote Control Sensor
POWER Button
Power/Standby Indicator
Illuminates red in standby mode.
Illuminates blue when the set is switched
on.
INPUT
ENTER
S t a n d (Only 42PG65C model)
INPUT
INPUT
MENU
INPUT
Button
MENU
VOL
ENTER
MENU
INPUT
ENTER
ENTER
MENU
Button
VOL
VOL
ENTER
Button
CH
CH
CH
VOLUME (-,+)
Buttons
CHANNEL (E, D)
Buttons
9
PREPARATION
BACK PANEL INFORMATION
Here shown may be somewhat different from your TV.
32/37/42LC5DC*,32/37/42LC50C*,
42LB5DC, 42LB50C
32LX5DC*, 32LX50C*
42PX8DC
S-VIDEO
R AUDIO RL/MONO VIDEO S-VIDEO
8
AV IN 2
ANTENNA IN
8
AV IN 2
11
11
M.P.I.
42PG60C, 42PG65C
NTENNA IN
S-VIDEO
VIDEO
OR
VIDEO L/MONO AUDIO
PREPARATION
11
AV IN 2
A
O R
L/MONO AUDIO
■
32/37/42LG500H
M.P.I.
S-VIDEO
)
VIDEO L/MONO AUDIO R
(
8
AV IN 2
AV IN 2
11
11
(
)
ANTENNA IN
ANTENNA IN
M.P.I.
M.P.I.
13
12
(
)
32/37/42LC5DC*, 32/37/42LC50C*,
42LB5DC, 42LB50C, 32LX5DC*, 32LX50C*, 42PX8DC
2
1
(
(
3
RESET
SERVICE ONLY
UPDATE
RGB IN
(
RJP
INTERFACE
10
VIDEO
AUDIO
COMPONENT IN
9
S-VIDEO
)
(MONO)
AUDIO
AV IN 1
8
)
5
REMOTE
CONTROL
OUT
M.P.I.
2
1(DVI)
(
4
DIGITAL
AUDIO
OUT
(OPTICAL)
)
HDMI/DVI IN
10
8
R
VIDEO L/MONO AUDIO R
R
S-VIDEO
VIDEO
SPEAKER AUDIO
IN
OUT
(RGB, DVI)
8
7
6
)
8
42PG60C, 42PG65C
6
10
RGB IN
DIGITAL
AUDIO OUT
RJP
SPEAKER
INTERFACE OUT
8
AUDIO
(RGB / DVI)
RGB(PC)
2
7
REMOTE
CONTROL
OUT
OPTICAL
4
1
SERVICE ONLY
COMPONENT IN
L
DVI IN
AUDIO
VIDEO
9
AUDIO
S-VIDEO
R
1
VIDEO L (MONO)
PREPARATION
2
UPDATE
RESET
AV IN 1
HDMI IN
R
8
5
32/37/42LG500H
1
OPTICAL
DIGITAL SPEAKER OUT
AUDIO OUT
8
6
HDMI/DVI IN
RESET
RGB IN
2
1(DVI)
RGB(PC)
UPDATE
AUDIO
(RGB/DVI)
RS-232C IN
(SERVICE ONLY)
AV IN 1
RJP
INTERFACE
AUDIO
VIDEO
10
COMPONENT IN
9
REMOTE
CONTROL OUT
/ MONO
S-VIDEO AUDIO
5
1
HDMI/DVI IN, HDMI IN
Connect a HDMI (DVI) connection to either input.
2
DIGITAL AUDIO OUT
Connect digital audio from various types of equipment.
Note: In standby mode, these ports do not work.
3 13
7
2
4
4
VIDEO
8
8
AV (Audio/Video) IN
Connect audio/video output from an external
device to these jacks.
S-VIDEO
Connect S-Video out from an S-VIDEO device.
9
COMPONENT IN
Connect a component video/audio device to these
jacks.
M.P.I
4
RESET/UPDATE/REMOTE CONTROL OUT
10
RJP INTERFACE
5
SERVICE ONLY
11
6
RGB IN (PC)
Connect the output from a PC.
AUDIO IN (RGB, DVI)
Connect the audio from a PC or DTV.
Power Cord Socket
For operation with AC power.
Caution: Never attempt to operate the TV on DC
power.
12
ANTENNA IN
Connect over-the air signals to this jack.
7
SPEAKER OUT 8Ω
11
PREPARATION
BACK COVER FOR WIRE ARRANGEMENT
■
Here shown may be somewhat different from your TV.
(This feature is not available for all models.)
Connect the cables as necessary.
To connect an additional equipment, see the EXTERNAL
EQUIPMENT SETUP section.
Secure the power cable with the PROTECTIVE
BRACKET and the screw as shown. It will help prevent
the power cable from being removed by accident.
1
PREPARATION
2
PROTECTIVE BRACKET
Install the CABLE HOLDER as shown.
CABLE HOLDER
2
Install the CABLE MANAGEMENT as shown.
CABLE MANAGEMENT
NOTE
G
Do not hold the CABLE MANAGEMENT when moving
the product.
- If the product is dropped, you may be injured or the
product may be damaged.
How to remove the CABLE MANAGEMENT
G
12
Hold the CABLE MANAGEMENT with both hands and
pull it backward.
BOLT
(This feature is not available for all models.)
To separate the CABLE HOLDER, loosen the bolt
installed the set.
2
Connect the cables as necessary.
To connect an additional equipment, see the EXTERNAL
EQUIPMENT SETUP section.
Secure the power cable with the PROTECTIVE
BRACKET and the screw as shown. It will help prevent
the power cable from being removed by accident.
PREPARATION
1
PROTECTIVE BRACKET
3
Install the CABLE HOLDER as shown.
BOLT CABLE
HOLDER
13
PREPARATION
BACK COVER FOR WIRE ARRANGEMENT
■
Here shown may be somewhat different from your TV.
42PG60C, 42PG65C
42PX8DC
1
Hold the CABLE MANAGEMENT with both
hands and pull it as shown.
Connect the cables as necessary.
To connect additional equipment, see the
EXTERNAL EQUIPMENT SETUP section.
2
Install the CABLE MANAGEMENT CLIP as
shown. (Except 42PG60C model)
If your TV has CABLE HOLDER, fix it as shown
and bundle the cables.
PREPARATION
1
45°
2
Connect the cables as necessary.
To connect an additional equipment, see the
EXTERNAL EQUIPMENT SETUP section.
CABLE MANAGEMENT
CLIP
3
Install the CABLE MANAGEMENT as shown.
CABLE HOLDER
How to remove the
CABLE MANAGEMENT CLIP
(Except 42PG60C model)
G
First, press the cable management. Hold the
C A B L E M A N A G E M E N T C L I P with both
hands and pull it upward.
! NOTE
G
14
Do not hold the CABLE MANAGEMENT CLIP
when moving the TV.
- If the TV is dropped, you may be injured or
the product may be broken.
32/37/42LG500H
BACK COVER FOR WIRE
ARRANGEMENT
1
1
Carefully place the TV screen side down on a cushioned surface to protect the screen from damage.
2
Assemble the parts of the S T A N D B O D Y
with C O V E R B A S E of the TV.
PREPARATION
Connect the cables as necessary.
To connect additional equipment, see the
EXTERNAL EQUIPMENT SETUP section.
Secure the power cable with the PLUG IN TYPE
HOLDER for power code and PROTECTIVE
BRACKET/Screw. It will help prevent the power
cable from being removed by accident.
STAND INSTALLATION
STAND BODY
PLUG IN TYPE HOLDER
PROTECTIVE BRACKET
(This feature is not available for all models.)
2
Install the CABLE MANAGEMENT CLIP as shown.
If your TV has the CABLE HOLDER, install it as
shown and bundle the cables.
COVER BASE
Assemble the TV as shown.
3
CABLE MANAGEMENT CLIP
CABLE HOLDER
3
Put the cables inside the CABLE MANAGEMENT
CLIP and snap it closed.
4
x4
Tighten the stand with the
four screws (provided as
parts of the TV).
or
PROTECTION COVER
Tighten the two of these four screws
x 2 and the two Torx plus star head screws
(provided as parts of the TV) to secure the TV. Tighten
the two Torx plus star head screws with a star head driver bit (not provided as parts of the TV).
x2
After removing the stand, install the included p r o t e c t i o n
c o v e r over the hole for the stand.
Press the P R O T E C T I O N C O V E R into the TV until you
hear it click.
! NOTE
G
When assembling the desk type stand, make sure
the bolt is fully tightened (If not tightened fully,
the TV can tilt forward after the product installation). Do not over tighten.
15
PREPARATION
STAND INSTALLATION
32/37LC5DC*, 32/37LC50C*
Carefully place the product screen side down
on a cushioned surface that will protect product and screen from damage.
2
Assemble the product stand with the product
as shown.
PREPARATION
1
3
16
42PG65C
1
Carefully place the TV screen side down on a
cushioned surface to protect the screen from
damage.
NOTE
G
After inserting the MPI slot/card, install the
product stand.
2
Assemble the product stand with the product as
shown.
3
Tighten the 4 bolts securely using the holes in
the back of the TV.
Securely install the 4 bolts provided as shown
below.
ATTACHING THE TV TO A WALL
This feature is not available for all models.
We recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards.
Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction,
potentially causing injury or damaging the product.
Caution: Please make sure that children don’t climb on or hang from the TV.
■
PREPARATION
■
Insert the TV brackets (or eye-bolts) and bolts to tighten the product to the wall as shown in the picture.
* If your product has the bolts in the eye-bolts position before inserting the eye-bolts, loosen the bolts.
Secure the wall brackets with the bolts (not provided as parts of the product, must purchase separately) on
the wall. Match the height of the bracket that is mounted on the wall to the holes in the product.
Ensure the eye-bolts or brackets are tightened securely.
■
Use a sturdy rope (not provided as parts of the product, must purchase separately) to tie the product. It is safer to tie the rope so it
becomes horizontal between the wall and the product.
SWIVEL STAND
20° (37LC5DC1, 42LC5DC, 42LC50C,
42PX8DC,
42LB5DC, 42LB50C, 42PG65C models)
90° (32LX5DC/S, 32LX50C/S, 32LC5DC/S,
32LC50C/S, 37LC5DC, 37LC50C, 32/37/42LG500H
models)
The TV can be conveniently swivelled on its stand 20°or 90° to the left or right to provide the optimum viewing angle.
17
PREPARATION
ATTACHING THE TV TO A DESK
■
Here shown may be somewhat different from your TV.
The TV must be attached to a desk so it cannot be pulled in a forward/backward direction, potentially causing injury or damaging the product.
10 mm)
* S c r e w s - M 5 x L ( t a b l e d e p t h + 8~1
ex) table depth-15mm: Bolts - M5 x 25
32/37/42LC5DC*, 32/37/42LC50C*, 42LB5DC, 42LB50C
PREPARATION
Stand
4-Screws
Desk
32LX5DC*, 32LX50C*
Stand
4-Screws
Desk
42PX8DC
Stand
2-Screws
Desk
42PG65C
Stand
4-Screws
Desk
18
32/37/42LG500H
Stand
1-Screw
(provided as parts of the product)
Desk
PREPARATION
WARNING
G
To prevent TV from falling over, the TV should be securely attached to the floor/wall per installation
instructions. Tipping, shaking, or rocking the machine may cause injury.
VESA WALL MOUNTING
This product accepts a VESA-compliant mounting interface pad. (optional)
There 4 threaded holes are available for attaching the bracket.
■
This feature is not available for all models.
Product
A
B
LCD TV
VESA
(A * B)
Model
32LC5DC*, 32LC50C*, 32LX5DC*,
32LX50C*
200 * 100
32/37/42LC5DC*, 32/37/42LC50C*,
42LB5DC, 42LB50C, 32/37/42LG500H
600 * 400
42PG60C
400 * 400
42PX8DC
600 * 400
PLASMA TV
NOTE
G
Screw length needed depends on the wall mount used. For further information, refer to the VESA
Wall Mounting Instruction Guide.
DESKTOP PEDESTAL INSTALLATION
For proper ventilation, allow a clearance of 4inches on each
side from the wall.
■
Image shown may differ from your TV.
■
This feature is not available for all models.
4 inches
4 inches
4 inches
4 inches
CAUTION
G
Ensure adequate ventilation by following the clearance recommendations.
19
PREPARATION
ANTENNA OR CABLE CONNECTION
1. Antenna (Analog or Digital)
Wall Antenna Socket or Outdoor Antenna without a Cable Box
Connections.
For optimum picture quality, adjust antenna direction if needed.
PREPARATION
Multi-family Dwellings/Apartments
(Connect to wall antenna socket)
Wall
Antenna
Socket
ANTENNA IN
M.P.I.
RF Coaxial Wire (75 ohm)
Outdoor
Antenna
(VHF, UHF)
Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)
Copper Wire
Be careful not to bend the bronze wire
when connecting the antenna.
2. Cable
ANTENNA IN
M.P.I.
Cable TV
Wall Jack
RF Coaxial Wire (75 ohm)
ANTENNA IN
UHF
M.P.I.
Signal
Amplifier
Antenna
VHF
To improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly.
If the antenna needs to be split for two TV’s, install a 2-Way Signal Splitter.
■ If the antenna is not installed properly, contact your dealer for assistance.
■
■
NOTE
20
G
The TV will let you know when the analog, cable, and digital channel scans are complete.
EXTERNAL EQUIPMENT SETUP
■
■
To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment.
This part of external equipment setup mainly use picture for LCD TV(Except 32/37/42LG500H) models.
HD RECEIVER SETUP
This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you
do receive digital signals from a digital set-top box or other digital external device, refer to the figure as shown
below.
When connecting Component cable
EXTERNAL EQUIPMENT SETUP
1. How to connect
1
2
Y
Connect the video outputs (Y, PB, PR) of the digital set
top box to the C O M P O N E N T I N V I D E O jacks on
the set. Match the jack colors
(Y = green, PB = blue, and PR = red).
PB
PR
DIGITAL
AUDIO
OUT
(OPTICAL)
HDMI/DVI IN
■
■
M.P.I.
2
1(DVI)
2. How to use
R
2
1
Connect the audio output of the digital set-top box to
the C O M P O N E N T I N A U D I O jacks on the set.
L
Turn on the digital set-top box.
(Refer to the owner’s manual for the digital set-top box.)
Select C o m p o n e n t input source with using the I N P U T
button on the remote control.
Signal
Component
HDMI1/DVI,
HDMI2
480i
Yes
No
480p
Yes
Yes
720p
Yes
Yes
1080i
Yes
Yes
1080p
Yes
Yes
(
RJP
RFACE
VIDEO
AUDIO
)
S-VIDEO
COMPONENT IN
* 42LB5DC, 42LB50C model only
21
EXTERNAL EQUIPMENT SETUP
When connecting HDMI cable
1. How to connect
EXTERNAL EQUIPMENT SETUP
1
Connect the digital set-top box to H D M I / D V I I N
1 ( D V I ) or 2 jack on the set.
2
No separated audio connection is necessary.
HDMI supports both audio and video.
HDMI/DVI IN
M.P.I
2
1(DVI)
2. How to use
■
(
)
■
Turn on the digital set-top box.
(Refer to the owner’s manual for the digital set-top box.)
VIDEO
RJP
INTERFACE
Select H D M I 1 / D V I or H D M I 2 input source with using
the I N P U T button on the remote control.
COMPONENT IN
1
NOTE
G
If the device does not support Auto HDMI, you need to set
the output resolution appropriately.
HDMI-DTV OUTPUT
(
22
DIGITAL
AUDIO
OUT
(OPTICAL)
)
AUDIO
When connecting HDMI to DVI cable
DIGITAL
AUDIO
OUT
(OPTICAL)
HDMI/DVI IN
RESET
SERVICE ONLY
M.P.I.
1(DVI)
UPDATE
REMOTE
CONTROL
OUT
RGB IN
VIDEO
RJP
INTERFACE
AUDIO
COMPONENT IN
S-VIDEO
(MONO)
AUDIO
AV IN 1
VIDEO
SPEAKER AUDIO
IN
OUT
(RGB, DVI)
8
1
2
DVI-DTV OUTPUT
L
EXTERNAL EQUIPMENT SETUP
2
R
1. How to connect
1
Connect the DVI output of the digital set-top box to the H D M I / D V I I N 1 ( D V I ) or 2 jack on the set.
2
Connect the audio output of the digital set-top box to the A U D I O I N ( R G B , D V I ) jack on the set.
2. How to use
■
Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.)
■
Select H D M I 1 / D V I or H D M I 2 input source with using the I N P U T button on the remote control.
23
EXTERNAL EQUIPMENT SETUP
DVD SETUP
When connecting Component cable
1. How to connect
1
EXTERNAL EQUIPMENT SETUP
2
Connect the video outputs (Y, PB, PR) of the DVD to
the C O M P O N E N T I N V I D E O jacks on the set.
Match the jack colors
(Y = green, PB = blue, and PR = red).
Connect the audio outputs of the DVD to the
C O M P O N E N T I N A U D I O jacks on the set.
2. How to use
PB
PR
1
■
Select C o m p o n e n t input source with using the I N P U T
button on the remote control.
R
DIGITAL
AUDIO
OUT
(OPTICAL)
(
RJP
ERFACE
VIDEO
AUDIO
COMPONENT IN
Refer to the DVD player's manual for operating instructions.
Component Input ports
To get better picture quality, connect a DVD player to the component input ports as shown below.
Component ports on the TV
Video output ports
on DVD player
24
Y
PB
PR
Y
PB
PR
Y
B-Y
R-Y
Y
Cb
Cr
Y
Pb
Pr
M.P.I.
2
1(DVI)
Turn on the DVD player, insert a DVD.
L
2
HDMI/DVI IN
■
■
Y
S-VIDEO
)
When connecting with an S-Video cable
AUDIO
1. How to connect
1
Connect the S-VIDEO output of the DVD to the
S - V I D E O input on the set.
2
Connect the audio outputs of the DVD to the A U D I O
input jacks on the set.
■
Turn on the DVD player, insert a DVD.
■
■
Select A V 1 input source with using the I N P U T button on
the remote control.
If connected to A V I N 2, select A V 2 input source.
■
Refer to the DVD player's manual for operating instructions.
GITAL
UDIO
OUT
TICAL)
L
R
1
2
RESET
S
REMOTE
CONTROL
OUT
M.P.I.
UPDATE
S-VIDEO
AUDIO
NT IN
(MONO)
VIDEO
AUDIO
AV IN 1
SPE
O
When connecting HDMI cable
1. How to connect
1
Connect the HDMI output of the DVD to the
H D M I / D V I I N 1 ( D V I ) or 2 jack on the set.
2
No separated audio connection is necessary.
HDMI supports both audio and video.
DIGITAL
AUDIO
OUT
(OPTICAL)
HDMI/DVI IN
2. How to use
(
■
Select H D M I 1 / D V I or H D M I 2 input source with using
the I N P U T button on the remote control.
■
Refer to the DVD player's manual for operating instructions.
EXTERNAL EQUIPMENT SETUP
2. How to use
S-VIDEO
M.P.I
2
1(DVI)
)
(
VIDEO
RJP
INTERFACE
AUDIO
COMPONENT IN
1
NOTE
G
If the device does not support Auto HDMI, you need to
set the output resolution appropriately.
HDMI-DVD OUTPUT
25
EXTERNAL EQUIPMENT SETUP
VCR SETUP
To avoid picture noise (interference), leave an adequate distance between the VCR and TV.
■ Use the ISM feature in the Option menu to avoid having a fixed image remain on the screen for a long period
of time. (Only Plasma TV model). If the 4:3 picture format is used; the fixed images on the sides of the screen
may remain visible on the screen. This phenomenon is common to all manufactures and in consequence the
manufactures warranty does not cover the product bearing this phenomenon.
■
When connecting with an antenna
EXTERNAL EQUIPMENT SETUP
ANTENNA IN
M.P.I.
M.P
.I.
1
S-VIDEO
VIDEO
L
R
ANT OUT
ANT IN
OUTPUT
SWITCH
Wall Jack
2
Antenna
1. How to connect
1
Connect the RF antenna out socket of the VCR to the A n t e n n a socket on the set.
2
Connect the antenna cable to the RF antenna in socket of the VCR.
2. How to use
26
■
Set VCR output switch to 3 or 4 and then tune TV to the same channel number.
■
Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.)
(
ANT IN
S-VIDEO
ANT OUT
OUTPUT
SWITCH
When connecting with a RCA cable
1. How to connect
1
V I D E O jacks between TV and
Connect the A U D I O/V
VCR. Match the jack colors (Video = yellow, Audio Left
= white, and Audio Right = red)
M.P.I.
TAL
DIO
UT
CAL)
)
L
VIDEO
R
1
RESET
SERV
REMOTE
CONTROL
OUT
M.P.I.
UPDATE
■
Insert a video tape into the VCR and press PLAY on the
VCR. (Refer to the VCR owner’s manual.)
R
(MONO)
S-VIDEO
AUDIO
VIDEO
AUDIO
T IN
AV IN 1
Select A V 1 input source with using the I N P U T button on
the remote control.
■ If connected to A V I N 2, select A V 2 input source.
SPEAKE
OUT
8
■
NOTE
G
If you have a mono VCR, connect the audio cable from the
VCR to the A U D I O
L / M O N O jack of the set.
EXTERNAL EQUIPMENT SETUP
2. How to use
When connecting with an S-Video cable
1. How to connect
ANT IN
S-VIDEO
ANT OUT
OUTPUT
SWITCH
L
R
VIDEO
M.P.I.
1
Connect the S-VIDEO output of the VCR to the
S - V I D E O input on the set.
2
Connect the audio outputs of the VCR to the A U D I O
input jacks on the set.
RESET
SER
M.P.I.
2. How to use
■
2
1
GITAL
AUDIO
OUT
PTICAL)
UPDATE
Insert a video tape into the VCR and press PLAY on the VCR.
(Refer to the VCR owner’s manual.)
AUDIO
■
Select A V 1 input source with using the I N P U T button on
the remote control.
■
If connected to A V I N 2, select A V 2 input source.
ENT IN
G
The picture quality is improved: compared to normal
composite (RCA cable) input.
(MONO)
AUDIO
AV IN 1
VIDEO
SPEAK
OUT
8
CAUTION
G
NOTE
S-VIDEO
REMOTE
CONTROL
OUT
Do not connect to both Video
and S-Video at the same time. In
the event that you connect both
Video and the S-Video cables,
only the S-Video will work.
27
EXTERNAL EQUIPMENT SETUP
OTHER A/V SOURCE SETUP
Camcorder
1. How to connect
Video Game Set
1
V I D E O jacks
Connect the A U D I O/V
between TV and external equipment.
Match the jack colors.
(Video = yellow, Audio Left = white, and
Audio Right = red)
VIDEO
L
R
■
Select A V 2 input source with using the
I N P U T button on the remote control.
■
If connected to A V I N 1 input, select A V 1
input source.
■
Operate the corresponding external equipment.
S-VIDEO
1
VIDEO L/MONO AUDIO R
EXTERNAL EQUIPMENT SETUP
2. How to use
AV IN 2
DIGITAL AUDIO OUTPUT
i.e) 32/37/42LC5DC*, 32/37/42LC50C*,
42LB5DC, 42LB50C
Send the TV’s audio to external audio equipment via the Digital Audio Output (Optical) port.
1. How to connect
1
Connect one end of an optical cable to the TV Digital
Audio (Optical) Output port.
2
Connect the other end of the optical cable to the
digital audio (optical) input on the audio equipment.
DIGITAL
AUDIO
OUT
(OPTICAL)
HDMI/DVI IN
Set the “TV Speaker option - Off” in the AUDIO
menu. (G p . 5 8). See the external audio equipment
instruction manual for operation.
3
NOTE
G
When connecting with external audio equipments, such as amplifiers or speakers, please turn the TV speakers off. (G p . 5 8)
CAUTION
G
28
Do not look into the optical output port. Looking at the
laser beam may damage your vision.
M.P.I.
2
1(DVI)
1
(
RJP
NTERFACE
VIDEO
AUDIO
COMPONENT IN
2
S-V
PC SETUP
This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings.
When connecting D-sub 15pin cable
SERVICE ONLY
1. How to connect
REMOTE
CONTROL
OUT
ATE
(
(
)
)
RGB IN
1
(MONO)
VIDEO
2
AUDIO
IN
(RGB, DVI)
SPEAKER
OUT
8
AUDIO
AV IN 1
EXTERNAL EQUIPMENT SETUP
Connect the RGB output of the PC to the R G B I N
jack on the set.
Connect the PC audio output to the A U D I O I N
( R G B , D V I ) jack on the set.
2. How to use
■
Turn on the PC and the set.
■
Select R G B - P C input source with using the I N P U T button
on the remote control.
2
1
When connecting HDMI to DVI cable
RGB OUTPUT
AUDIO
1. How to connect
1
2
Connect the DVI output of the PC to the H D M I / D V I
I N 1 ( D V I ) jack on the set.
DIGITA
AUDIO
OUT
(OPTICA VICE ONLY
HDMI/DVI IN
2
1(DVI)
RGB IN
Connect the PC audio output to the A U D I O I N
( R G B / D V I) jack on the set.
(
)
(
)
ER
VIDEO
RJP
INTERFACE
COMPONENT
AUDIO
IN
(RGB, DVI)
(
)
1
2. How to use
■
Turn on the PC and the set
■
Select H D M I 1 / D V I input source with using the I N P U T
button on the remote control.
2
DVI-PC OUTPUT
AUDIO
29
EXTERNAL EQUIPMENT SETUP
NOTES
G
Depending on the graphics card, DOS mode may
not work if a HDMI to DVI Cable is in use.
G
Check the image on your TV. There may be noise
associated with the resolution, vertical pattern,
contrast or brightness in PC mode. If noise is present, change the PC output to another resolution,
change the refresh rate to another rate or adjust
the brightness and contrast on the VIDEO menu
until the picture is clear. If the refresh rate of the
EXTERNAL EQUIPMENT SETUP
Supported Display Specifications (RGB/HDMI1-PC)
Resolution
Horizontal
Frequency(KHz)
Vertical
Frequency(Hz)
640x350
31.469
70.08
640x480
31.469
37.861
37.500
59.94
72.80
75.00
800x600
35.156
37.879
48.077
46.875
56.25
60.31
72.18
75.00
1024x768
48.363
56.476
60.023
60.00
70.06
75.02
1280x768
47.700
60.00
1360x768
47.720
59.799
1366x768
47.130
59.658
PC graphic card can not be changed, change the
PC graphic card or consult the manufacturer of
the PC graphic card.
G
Avoid keeping a fixed image on the screen for a
long period of time. The fixed image may become
permanently imprinted on the screen.
The synchronization input form for Horizontal and
Vertical frequencies is separate.
G
Supported Display Specifications (HDMI2-DTV)
Resolution
Horizontal
Frequency(KHz)
Vertical
Frequency(Hz)
720x480
31.500
31.469
60.00
59.94
1280x720
44.960
45.000
59.94
60.00
1920x1080
33.720
33.750
59.94
60.00
Supported Display Specifications (Y, CB /PB, CR /PR)
Resolution
Horizontal
Frequency(KHz)
Vertical
Frequency(Hz)
720x480
15.73
15.73
31.47
31.50
59.94
60.00
59.94
60.00
1280x720
44.96
45.00
59.94
60.00
1920x1080
33.72
33.75
59.94
60.00
Supported Display Specifications (RGB/HDMI1-DTV)
Resolution
720x480
Horizontal
Frequency(KHz)
Vertical
Frequency(Hz)
31.50
60.00
31.47(HDMI1-DTV:31.469) 59.94
* RGB-DOS mode only: 640x350
1280x720
44.96
45.00
59.94
60.00
1920x1080
33.72
33.75
59.94
60.00
* Except 42PG60C/65C models in HDMI1-PC mode.
30
* 42LB5DC, 42LB50C
Supported Display Specifications (RGB/HDMI1-PC)
Horizontal
Frequency(KHz)
Vertical
Frequency(Hz)
31.469
70.08
640x480
31.469
37.861
37.500
Supported Display Specifications (HDMI2-DTV)
Horizontal
Frequency(KHz)
Vertical
Frequency(Hz)
720x480
31.500
31.469
60.00
59.94
59.94
72.80
75.00
1280x720
44.960
45.000
59.94
60.00
800x600
35.156
37.879
48.077
46.875
56.25
60.31
72.18
75.00
1920x1080
33.720
33.750
67.500
59.94
60.00
60.00
1024x768
48.363
56.476
60.023
60.00
70.06
75.02
1280x768
47.700
60.00
1360x768
47.720
59.799
1366x768
47.130
59.658
1280x1024
63.668
59.895
65.317
59.978
640x350
(RGB only)
(RGB only)
1400x1050
(RGB only)
1600x1200
74.537
59.869
1920x1080
66.587
59.934
1920x1200
74.038
59.950
Supported Display Specifications (Y, CB /PB, CR /PR)
Resolution
Horizontal
Frequency(KHz)
Vertical
Frequency(Hz)
720x480
15.73
15.73
31.47
31.50
59.94
60.00
59.94
60.00
1280x720
44.96
45.00
59.94
60.00
1920x1080
33.72
33.75
67.50
59.94
60.00
60.00
EXTERNAL EQUIPMENT SETUP
Resolution
Resolution
* RGB-DOS mode only: 640x350
Supported Display Specifications (RGB/HDMI1-DTV)
Resolution
720x480
Horizontal
Frequency(KHz)
Vertical
Frequency(Hz)
31.50
60.00
31.47(HDMI1-DTV:31.469) 59.94
1280x720
44.96
45.00
59.94
60.00
1920x1080
33.72
33.75
59.94
60.00
59.94
67.43(HDMI1-DTV:67.5)
31
WATCHING TV / CHANNEL CONTROL
REMOTE CONTROL FUNCTIONS
When using the remote control, aim it at the remote control sensor on the TV.
POWER Turns your TV or any other programmed equipment on
or off, depending on mode.
TV INPUT
In AV 1-2, Component, RGB, HDMI1/DVI, and HDMI2
input sources, screen returns to the last TV channel.
External input modes rotate in regular sequence: TV, AV1INPUT 2, Component, RGB, HDMI1/DVI and HDMI2.
INPUT
TV
MODE
TV
POWER
INPUT
DVD
MULTI
VCR
PIP CH - PIP CH + PIP INPUT
PIP
EZ PIC
EZ SOUND
INFO
SWAP
MULTI Selects: RGB,HDMI1/DVI, HDMI2 and Component input
sources.
WATCHING TV / CHANNEL CONTROL
Adjusts brightness on screen.
MENU
EXIT
RATIO
SAP
PIP CH +/- Changes the PIP channel. G p . 4 2
PIP INPUT Select the connected input source for the sub-picture. G p.41
ENTER
Selects the factory preset picture depend on the viewing
EZ PIC environment. p.45
G
TIMER
EZ SOUND Selects the factory preset sound for type of program.
p.55
SWAP(or PIP
SWAP) Exchange the main/sub images. G p . 4 2
VCR/DVD Control video cassette recorders or DVD players.
control buttons
NUMBER button
— (DASH) Used to enter a program number for multiple program
channels such as 2-1, 2-2, etc.
FLASH BACK Tune to the last channel viewed.
32
CC
PIP Switches the sub picture Double Window or off mode. G p.41-42
G
CH PAGE
VOL
MUTE
1
2
3
4
5
6
7
8
9
0
FLASH
BACK
(Only 42PG60C, 42PG65C, 32/37/42LG500H models)
TV
POWER
DVD
CC
INPUT
VCR
STB
RATIO
MODE Select the remote’s operating mode: TV, DVD, VCR (or
STB).
RATIO Change the aspect ratio.
G
p.43- 4 4
CC Select a closed caption. G p.62 (*In DTV/CADTV mode G p.63)
THUMBSTICK Navigate the on-screen menus and adjust the system set(Up/Down/Left tings to your preference.
ENTER
/Right/ENTER)
EXIT(or Clears all on-screen displays and returns to TV viewing
RETURN) from any menu.
RETURN
MENU
INFO i
MENU Displays the main menu.
CH
VOL
P
A
G
E
MUTE
1
2
3
4
5
6
7
8
9
0
FLASHBK
PIP
PIP CH-
VOLUME UP Increase/decrease the sound level.
/DOWN
TIMER Select the amount of time before your TV turns off automatically. G p .6 9
MUTE Switch the sound on or off. G p.34
CHANNEL Select available channels.
UP/DOWN
PAGE Move from one full set of screen information to the next one.
UP/DOWN
SAP
PIP CH+ PIP SWAP PIP INPUT
Installing Batteries
Remote control effective range
32/37/42LC5DC*,
42LB5DC, 32/37/42LC5DC*, 32LX5DC*, 32LX50C*
32/37/42LC50C*,
42LB5DC, 42LB50C
42PX8DC
INPUT
■
■
■
WATCHING TV / CHANNEL CONTROL
INFO Display information at the top of the screen.
TIMER
INPUT
TV
Open the battery compartment cover on the back
side and install the batteries matching correct
polarity (+ with +, - with -).
Install two 1.5V AA batteries(or 1.5V AAA)
Don’t mix old or used batteries with new ones.
Close cover.
INPUT
TV
MODE
TV
POWER
INPUT
DVD
MODE
TV
POWER
INPUT
INPUT
TV
MODE
TV
POWER
VCR
MULTI
INPUT
DVD
DVD
VCR
MULTI
PIP CH - PIP CH + PIP INPUT
PIP
EZ PIC
EZ SOUND
INFO
SWAP
PIP CH - PIP CH + PIP INPUT
PIP
EZ PIC
ENTER
EZ SOUND
INFO
SWAP
VCR
MULTI
PIP CH - PIP CH + PIP INPUT
PIP
EZ PIC
EZ SOUND
INFO
SWAP
CC
MENU
EXIT
CC
MENU
EXIT
RATIO
SAP
RATIO
SAP
CC
MENU
EXIT
ENTER
ENTER
RATIO
SAP
ENTER
TIMER
CH PAGE
VOL
TIMER
MUTE
CH PAGE
VOL
MUTE
TIMER
3
MUTE
1
2
1
2
3
5
6
3
Use a remote control up to 22 feet distance
and 30 degree (left/right) within the receiving
unit scope.
INPUT
INPUT
■
2
4
CH PAGE
VOL
1
■
ENTER
ENTER
Dispose of used batteries in a recycle bin to
preserve environment.
33
WATCHING TV /CHANNEL CONTROL
TURNING ON TV
First, connect power cord correctly.
At this moment, the TV switches to standby mode.
■ In standby mode to turn TV on, press the
(or O N / O F F) button on
the TV or press the POWER button on the remote control.
1
WATCHING TV / CHANNEL CONTROL
2
Select the viewing source by using the INPUT(or TV INPUT) button on
the remote control.
■ This TV is programmed to remember which power state it was last set to,
even if the power cord is out.
3
When finished using the TV, press the POWER button on the remote control. The TV reverts to standby mode.
NOTE
G
If you intend to be away on vacation, disconnect the power plug from the wall power outlet.
CHANNEL SELECTION
1
Press the CH ( + or - ) or C H (
a channel number.
or
) or NUMBER buttons to select
VOLUME ADJUSTMENT
Adjust the volume to suit your personal preference.
34
1
Press the VOL ( + or -) button to adjust the volume.
2
If you want to switch the sound off, press the M U T E button.
3
You can cancel the Mute function by pressing the M U T E or VOL ( + or -)
button.
ON-SCREEN MENUS SELECTION
Your TV's OSD (On Screen Display) may differ slightly from what is shown in this manual.
1
Press the M E N U button and then use
menu.
2
Press the G or
available menus.
button and then use D
SETUP
AUDIO
TIME
OPTION
E F G
or
or
VIDEO
VIDEO
Manual Scan
AUDIO
Channel Edit
TIME
DTV Signal
OPTION
Channel Label
button to display the
AUDIO
SETUP
EZ Scan
button to select the each
SETUP
EZ Picture
VIDEO
Color Temperature
AUDIO
XD
TIME
Advanced
OPTION
Reset
SCREEN
SCREEN
SCREEN
LOCK
LOCK
LOCK
Audio Language
EZ SoundRite
EZ Sound
Balance
TV Speakers
TIME
LOCK
For USA
For Canada
SETUP
Auto Clock
VIDEO
SETUP
VIDEO
AUDIO
TIME
OPTION
SCREEN
Lock System
Set Password
Block Channel
Movie Rating
TV Rating-Children
TV Rating-General
LOCK
Aux. Block
Lock System
Set Password
Manual Clock
AUDIO
Off Timer
TIME
On Timer
Block Channel
OPTION
TV Rating-English
SCREEN
TV Rating-French
0
WATCHING TV / CHANNEL CONTROL
SETUP
VIDEO
or E or
D
Auto Off
LOCK
Aux. Block
Downloadable Rating
Downloadable Rating
OPTION
SCREEN
SETUP
VIDEO
AUDIO
TIME
SETUP
VIDEO
Auto config.
Manual config.
XGA Mode
Reset
AUDIO
TIME
Aspect Ratio
Caption/Text
Caption Options
Language
OPTION
OPTION
SCREEN
SCREEN
LOCK
ISM Method
Low Power
Set ID
LOCK
Only 42PX8DC model
35
WATCHING TV /CHANNEL CONTROL
CHANNEL SETUP
Auto Scan (EZ Scan)
Automatically finds all channels available through antenna
or cable inputs, and stores them in memory on the channel
list.
Run EZ Scan again after any Antenna/Cable connection
changes.
A password is required to gain access to EZ Scan menu if
the Lock System is turned on.
WATCHING TV / CHANNEL CONTROL
SETUP
VIDEO
1
Press the M E N U button and then use D or E or
or
button to select the S E T U P menu.
AUDIO
TIME
OPTION
EZ Scan
Manual Scan
Channel Edit
DTV Signal
Channel Label
SCREEN
LOCK
2
Press the G or
button and then use
or
button to select E Z S c a n.
D
or E or
1
3
Press the E N T E R button to begin the channel search.
Allow E Z S c a n to complete the channel search cycle
for A N T E N N A and C A B L E.
SETUP
VIDEO
AUDIO
TIME
OPTION
EZ Scan
G
Manual Scan
Channel Edit
DTV Signal
Channel Label
SCREEN
Selection ( G or
) leads you
to the EZ scan screen.
LOCK
2
SETUP
EZ Scan
G
VIDEO
Manual Scan
AUDIO
Channel Edit
Processing EZ scan...
TIME
DTV Signal
OPTION
SCREEN
LOCK
Channel Label
Selection ( G or
) leads you
to the EZ scan screen.
ANALOG
Found Channel(s)
Next
MENU Prev.
3
36
9
4
Add/Delete Channel (Manual Scan)
A password is required to gain access to Manual Scan
menu if the Lock System is turned on.
1
Press the M E N U button and then use D or E or
or
button to select the SETUP menu.
AUDIO
TIME
OPTION
EZ Scan
Manual Scan
Channel Edit
DTV Signal
Channel Label
SCREEN
LOCK
2
Press the G or
button and then use D or E or
or
button to select Manual Scan.
1
3
Press the G or
button and then use D or E or
T V, C A T V),
or
button to select Analog(T
D T V, C A D T V).
Digital(D
SETUP
VIDEO
AUDIO
TIME
OPTION
4
Press the G or
button and then use D or E or
or
button to select channel you want to add or
delete.
EZ Scan
Manual Scan
Channel Edit
G
Channel Type
Number
ANALOG
2
DTV Signal
Channel Label
WATCHING TV / CHANNEL CONTROL
SETUP
VIDEO
SCREEN
LOCK
2
5
Press the ENTER button to add or delete the channel.
SETUP
VIDEO
6
Press the E X I T or RETURN button to return to TV
viewing or press M E N U button to return to the previous menu.
AUDIO
TIME
OPTION
EZ Scan
Manual Scan
Channel Edit
DTV Signal
Channel Type
D
E
ANALOG
Number
G
2
ANALOG 2
Channel Label
SCREEN
LOCK
Press
to delete the channel.
3
4
5
37
WATCHING TV /CHANNEL CONTROL
Channel Editing
A Custom List can be created by toggling each channel on
or off with ENTER button. The channels in the Custom List
are displayed in black, and the channels deleted from the
Custom List are displayed in gray. Once a channel is highlighted you can add or delete the channel by referring to the
small window at the top-left corner of the screen.
A password is required to gain access to Manual Scan menu
if the Lock System is turned on.
WATCHING TV / CHANNEL CONTROL
SETUP
VIDEO
AUDIO
TIME
OPTION
EZ Scan
Manual Scan
Channel Edit
DTV Signal
Channel Label
SCREEN
LOCK
1
Press the M E N U button and then use D or E or
or
button to select the SETUP menu.
1
SETUP
2
Press the G or
button and then use D or E or
or
button to select C h a n n e l E d i t.
VIDEO
AUDIO
TIME
OPTION
3
Press the G or
button and then use D or E or
or
button to select A N A L O G or D I G I T A L.
4
Press the G or
button and then use D or E or
or
button to select channel and then use the
ENTER button to add or delete it.
ANALOG
EZ Scan
2-0
Manual Scan
Channel Edit
D
4-0
G
6-0
DTV Signal
9-0
Channel Label
SCREEN
11-0
LOCK
13-0
14-0
E
2
SETUP
VIDEO
AUDIO
TIME
OPTION
5
Press E X I T or RETURN button to return to TV viewing or press M E N U button to return to the previous
menu.
EZ Scan
D
E
ANALOG
Manual Scan
2-0
Channel Edit
4-0
DTV Signal
6-0
Channel Label
9-0
SCREEN
11-0
LOCK
13-0
G
D
14-0
E
3
38
4
DTV SIGNAL STRENGTH
This feature displays the DTV signal levels being received
and indicates whether you need to adjust your antenna or
digital cable input. The higher the signal strength, the less
likely you are to experience picture degradation.
DTV Signal: This function is only available when the input
signal is DTV or CADTV.
1
Press the M E N U button and then use D or E or
or
button to select the S E T U P menu.
AUDIO
TIME
OPTION
EZ Scan
Manual Scan
Channel Edit
DTV Signal
Channel Label
SCREEN
LOCK
2
Press the G or
button and then use D or E or
or
button to select D T V S i g n a l .
3
View the on-screen signal strength monitor to see
the quality of the signal being received.
1
SETUP
VIDEO
AUDIO
TIME
4
Press EXIT or RETURN button to return to TV viewing or press M E N U button to return to the previous menu.
OPTION
EZ Scan
Manual Scan
Channel Edit
Bad
Normal
Good
DTV Signal
WATCHING TV / CHANNEL CONTROL
SETUP
VIDEO
Channel Label
SCREEN
LOCK
2
3
39
WATCHING TV /CHANNEL CONTROL
CHANNEL LABEL
Choose preset labels for your channels.
If a channel label is provided on the signal from the
broadcasting station, the TV displays a short name for a
channel even if you didn't preset a label for the channel.
WATCHING TV / CHANNEL CONTROL
SETUP
1
VIDEO
Press the M E N U button and then use D or E or
or
button to select the S E T U P menu.
AUDIO
TIME
OPTION
EZ Scan
Manual Scan
Channel Edit
DTV Signal
Channel Label
SCREEN
LOCK
2
Press the G or
button and then use D or E or
or
button to select C h a n n e l L a b e l .
1
3
Press the G or
button and then use D or E or
or
button to select a channel to label.
SETUP
VIDEO
AUDIO
TIME
OPTION
4
Press the G or
button and then use D or E or
or
button to select the appropriate label for the
channel.
5
Press E X I T or RETURN button to return to TV viewing
or press M E N U button to return to the previous menu.
SCREEN
EZ Scan
Manual Scan
Channel Edit
DTV Signal
Channel Label
G
Ch.
Logo
ANALOG 2
No Logo
LOCK
2
40
3
PICTURE CONTROL
WATCHING DW (DOUBLE WINDOW)
Double Window mode splits the screen into two images, allowing two picture
sources to be shown on the TV screen at the same time. Each source is given half
the screen.
Watching Double Window
Press the P I P button to access the sub picture.
DW Mode
PIP Off
PICTURE CONTROL
Selecting an Input Signal Source for Double Window
Use the P I P I N P U T button to select the input source for the sub picture.
Each press of P I P I N P U T button changes the PIP source.
Use the P I P I N P U T button to select the input source for the sub picture. Each press of PIP INPUT button
changes the PIP source.
Main Picture Source
Available Sub Picture Sources
TV
AV1, AV2
AV1
TV, AV2
AV2
TV, AV1
RGB, Component, HDMI1/DVI, HDMI2
TV, AV1, and AV2
41
PICTURE CONTROL
TV Program Selection for PIP
1
Use the P I P C H + / - button to select a channel for the sub picture.
The selected channel number is displayed just below the input source of main picture.
Swapping the PIP / Double Window
PICTURE CONTROL
42
1
Repeatedly, use the S W A P or P I P S W A P button to switch the main and sub pictures.
■
Component, RGB, HDMI1/DVI, HDMI2 input sources for the main picture can’t be used to swap the
main and sub pictures.
PICTURE SIZE (ASPECT RATIO) CONTROL
This feature allows an analog picture with a 4:3 aspect ratio is displayed on your TV.
When you receive an analog picture with a 4:3 aspect ratio on your 16:9 TV, you
need to specify how the picture is to be displayed.
■ RGB-PC/DVI-PC input source use 4:3 or 16:9 aspect ratio.
1
Press the RATIO button repeatedly to select the desired picture format.
■ You can also adjust A s p e c t R a t i o in the O P T I O N menu.
Set by program
Selects the proper picture proportion to match the source’s image.
4:3)
(16:9
16:9)
Set By Program
Set By Program
PICTURE CONTROL
(4:3
4:3
Choose 4:3 when you want to view a picture with an original 4:3 aspect ratio.
4:3
16:9
Adjust the picture horizontally, in a linear proportion to fill the entire screen.
16:9
43
PICTURE CONTROL
Horizon
The screen size is, more enlarged at both sides, to create a spectacular view.
Horizon
PICTURE CONTROL
Zoom 1
Choose Zoom 1 when you want to view the picture without any alteration. However, the top and bottom portions
of the picture will be cropped.
Zoom 1
Zoom 2
Choose Zoom 2 when you want the picture to be altered, both vertically extended and cropped. The picture taking a halfway trade off between alteration and screen coverage.
Zoom 2
44
PRESET PICTURE SETTINGS
EZ Picture - Preset
EZ Picture adjusts the TV for the best picture appearance. Select
the preset value in the EZ Picture menu based on the program
category.
Daylight, Normal, Night Time Settings are preset for the optimum picture quality at the factory and are not adjustable.
In the U s e r 1 and U s e r 2 modes only, user can directly adjust
the contrast, brightness, color, sharpness, tint.
1
■
PICTURE CONTROL
2
Press the E Z P I C button repeatedly to select the picture
appearance setup option as below(Except 42PG60C,
42PG65C models):
D a y l i g h t, N o r m a l, N i g h t T i m e, U s e r 1, and U s e r 2
(your own settings).
Press the E X I T or R E T U R N button to save and return to TV
viewing.
You can also use the VIDEO menu to adjust E Z P i c t u r e.
SETUP
VIDEO
AUDIO
TIME
OPTION
EZ Picture
Color Temperature
XD
Advanced
Reset
SETUP
VIDEO
AUDIO
TIME
OPTION
SCREEN
SCREEN
LOCK
LOCK
EZ Picture
G
Daylight
Color Temperature
Normal
XD
Night time
Advanced
User 1
Reset
User 2
45
PICTURE CONTROL
Color Tone - Preset
Choose one of three automatic color adjustments. Set to
warm to enhance hotter colors such as red, or set to cool
to see less intense colors with more blue.
When selecting EZ Picture (User 1 and User 2), you can
choose the Color Temperature.
SETUP
1
VIDEO
Press the M E N U button and then use D or E or
or
button to select the V I D E O menu.
AUDIO
TIME
PICTURE CONTROL
OPTION
EZ Picture
Color Temperature
XD
Advanced
Reset
SCREEN
LOCK
2
Press the G or
button and then use D or E or
or
button to select C o l o r T e m p e r a t u r e.
1
3
Press the G or
button and then use D or E or
or
button to select either C o o l, N o r m a l, W a r m or
U s e r.
SETUP
VIDEO
AUDIO
TIME
OPTION
4
Press E X I T or R E T U R N button to return to TV viewing or press M E N U button to return to the previous
menu.
EZ Picture
Color Temperature
G
Cool
XD
Normal
Advanced
Warm
Reset
User
SCREEN
LOCK
2
46
3
MANUAL PICTURE ADJUSTMENT
EZ Picture - User Mode
Adjust the picture appearance to suit your preference and
viewing situations.
This feature operate only if the EZ Picture set User 1 or
User 2.
SETUP
1
EZ Picture
VIDEO
Press the M E N U button and then use D or E or
or
button to select the V I D E O menu.
Color Temperature
AUDIO
XD
TIME
Advanced
Reset
SCREEN
LOCK
2
Press the G or
button and then use D or E or
or
button to select E Z P i c t u r e.
1
3
Press the G or
button and then use D or E or
or
button to select U s e r 1 or U s e r 2.
SETUP
EZ Picture
Daylight
Color Temperature
Normal
XD
Night Time
Advanced
User 1
Reset
User 2
VIDEO
PICTURE CONTROL
OPTION
AUDIO
TIME
OPTION
G
SCREEN
4
Press the G or
button and then use D or E or
or
button to select the desired picture option
( C o n t r a s t, B r i g h t n e s s, C o l o r, S h a r p n e s s, or
T i n t) .
LOCK
2
3
SETUP
5
Press the G or
button and then use F or G or
or
button to make appropriate adjustments.
VIDEO
User1
AUDIO
Contrast
85
Brightness
50
TIME
OPTION
Color
50
SCREEN
Sharpness
50
LOCK
6
Tint
G
0
R
Press E X I T or R E T U R N button to return to TV viewing or press M E N U button to return to the previous
menu.
G
4
SETUP
VIDEO
Contrast
AUDIO
85 F
G
E
TIME
OPTION
SCREEN
LOCK
5
47
PICTURE CONTROL
Color Tone - User Mode
You can also adjust the detailed settings (Red, Green, Blue)
by selecting the C o l o r T e m p e r a t u r e - U s e r menu.
SETUP
1
Press the M E N U button and then use D or E or
or
button to select the V I D E O menu.
VIDEO
AUDIO
TIME
PICTURE CONTROL
OPTION
EZ Picture
Color Temperature
XD
Advanced
Reset
SCREEN
2
Press the G or button and then use D or E or
or
button to select C o l o r T e m p e r a t u r e.
3
Press the G or button and then use D or E or
or
button to select U s e r.
LOCK
1
SETUP
VIDEO
AUDIO
TIME
OPTION
4
Press the G or button and then use D or E or
or
button to select R e d, G r e e n, or B l u e.
5
Press the G or button and then use F or G or
or
button to make appropriate adjustments.
■
The adjustment range of R e d, G r e e n , or B l u e is
-40 ~ +40.
EZ Picture
Color Temperature
Cool
XD
Normal
Advanced
Warm
Reset
User
G
SCREEN
LOCK
2
3
SETUP
VIDEO
User
AUDIO
Red
0
Green
0
Blue
0
TIME
OPTION
G
SCREEN
LOCK
6
Press E X I T or R E T U R N button to return to TV viewing or press M E N U button to return to the previous
menu.
4
SETUP
VIDEO
AUDIO
Red
0 F
G
E
TIME
OPTION
SCREEN
LOCK
48
5
XD - PICTURE IMPROVEMENT TECHNOLOGY
XD is LG Electronic’s unique picture improving technology
to display a real HD source through an advanced digital signal processing algorithm.
When selecting EZ Picture options (Daylight, Normal and
Night time), XD is automatically changed to Auto.
When selecting EZ Picture options (User 1 and User 2), you
can choose the Auto / Manual.
When selecting the Manual, you can adjust the XD
Contrast, XD color and XD Noise.
SETUP
1
VIDEO
AUDIO
TIME
OPTION
EZ Picture
Color Temperature
XD
Advanced
Reset
SCREEN
2
Press the G or
button and then use
or
button to select X D.
3
Press the G or
button and then use D or
or
button to select A u t o or M a n u a l.
D
or
E
or
E
or
LOCK
1
Selecting the Manual Mode
button and then use D or E
1. Press the G or
or
or
button to select X D C o n t r a s t, X D
C o l o r or X D N R ( N o i s e ), M P E G N R.
■ X D C o n t r a s t : Optimizing the contrast automatically according to the brightness of the reflection.
■ X D C o l o r : Adjusting the colors of the reflection
automatically to reproduce as closely as possible
to the natural colors.
■ X D N R ( N o i s e ) : Removing the noise up to the
point where it does not damage the original picture.
■ M P E G N R : To reduce the picture noise which may
appear on the screen during watching the TV.
or
button to select O n
2. Press the F or G or
or O f f.
4
SETUP
VIDEO
AUDIO
TIME
OPTION
EZ Picture
Color Temperature
XD
Advanced
Reset
G
Auto
Manual
XD Contrast
On
SCREEN
LOCK
PICTURE CONTROL
Press the M E N U button and then use D or E or
or
button to select the V I D E O menu.
XD Color
On
XD NR
Off
MPEG NR
0
2
3
Press E X I T or R E T U R N button to return to TV viewing or press M E N U button to return to the previous
menu.
49
PICTURE CONTROL
ADVANCED - CINEMA MODE
Set up the TV for the best picture appearance for viewing
movies.
When you operate Cinema (3:2 Pull-Down Mode or Cinema
Correction Mode), the TV will adjust 24 fps video from
movies to 30 fps video for display.
This feature operates only in Analog, AV1, AV2, and
Component 480i mode.
SETUP
VIDEO
1
Press the M E N U button and then use D or E or
or
button to select the V I D E O menu.
AUDIO
TIME
PICTURE CONTROL
OPTION
Color Temperature
XD
Advanced
Reset
SCREEN
2
Press the G or
button and then use D or E or
or
button to select A d v a n c e d.
3
Press the G or
button and then use D or E or
or
button to select C i n e m a.
LOCK
1
SETUP
VIDEO
AUDIO
TIME
4
5
50
EZ Picture
Press the G or
button and then use D or E or
or
button to select O n or O f f.
Press E X I T or R E T U R N button to return to TV viewing or press M E N U button to return to the previous
menu.
OPTION
SCREEN
LOCK
EZ Picture
Color Temperature
XD
Advanced
G
Cinema
Off
Reset
Black level
Low
2
3
4
ADVANCED - BLACK (DARKNESS) LEVEL
Adjusting the contrast and the brightness of the screen
using the black level of the screen.
This feature operates only in AV1, AV2, HDMI1/DVI, or
HDMI2mode.
SETUP
1
Press the M E N U button and then use D or E or
or
button to select the V I D E O menu.
VIDEO
AUDIO
TIME
Color Temperature
XD
Advanced
Reset
SCREEN
2
Press the G or
button and then use D or E or
or
button to select A d v a n c e d.
3
Press the G or
button and then use D or E or
or
button to select B l a c k l e v e l.
LOCK
1
SETUP
VIDEO
4
Press the G or
button and then use D or E or
or
button to select L o w or H i g h.
■ Low
The screen gets darker.
■ High
The screen gets brighter.
AUDIO
TIME
OPTION
SCREEN
LOCK
EZ Picture
Color Temperature
XD
Advanced
G
Cinema
Off
Reset
Black level
Low
2
5
PICTURE CONTROL
OPTION
EZ Picture
3
4
Press E X I T or R E T U R N button to return to TV viewing or press M E N U button to return to the previous
menu.
51
PICTURE CONTROL
PICTURE RESET
Use to quickly reset all the Video menu options to their
original factory preset values.
SETUP
VIDEO
AUDIO
TIME
OPTION
1
Press the M E N U button and then use D or
or
button to select the VIDEO menu.
2
button and then use D or E or
Press the G or
or
button to select Reset.
E
XD
Advanced
Reset
LOCK
1
SETUP
AUDIO
PICTURE CONTROL
Press the G or
button to reset the Video menu
options to original values.
Color Temperature
SCREEN
or
VIDEO
3
EZ Picture
TIME
OPTION
EZ Picture
Color Temperature
XD
Advanced
Reset
To set
G
SCREEN
LOCK
2
3
LOW-POWER PICTURE MODE (Only 42PX8DC model)
Low power reduces the plasma display power consumption.
SETUP
VIDEO
1
Press the M E N U button and then use D or E or
or
button to select the OPTION menu.
AUDIO
TIME
Aspect Ratio
Caption/Text
Caption Options
Language
OPTION
SCREEN
ISM Method
Low Power
LOCK
2
Set ID
Press the G or
button and then use D or E or
or
button to select L o w P o w e r.
1
3
Press the G or
button and then use D or E or
or
button to select O n or O f f.
SETUP
VIDEO
AUDIO
■
When you select On, the screen darkens.
TIME
OPTION
SCREEN
LOCK
4
Press E X I T or R E T U R N button to return to TV viewing or press M E N U button to return to the previous
menu.
Aspect Ratio
Caption/Text
Caption Options
Language
ISM Method
Low Power
Set ID
G
Off
On
2
52
3
IMAGE STICKING MINIMIZATION(ISM) METHOD
A frozen still picture from a PC/video game displayed on
the screen for prolonged periods will result in a ghost
image. Use our unique method to minimize any fixed image
on the screen.
1
Press the M E N U button and then use D or E or
or
button to select the OPTION menu.
2
button and then use D or E or
Press the G or
or
button to select ISM Method.
SETUP
VIDEO
TIME
Caption/Text
Caption Options
Language
OPTION
SCREEN
ISM Method
Low Power
LOCK
■
Set ID
Normal
If image sticking is never a problem, ISM is not necessary
set to Normal.
1
■
White wash
White Wash removes permanent images from the
screen.
SETUP
VIDEO
AUDIO
NOTE
TIME
OPTION
An excessive permanent image may be impossible
to clear entirely with White Wash. To return to
normal viewing, press any button.
■
■
4
Orbiter
Orbiter may help prevent ghost images. However, it
is best not to allow any fixed image to remain on the
screen. To avoid a permanent image on the screen,
the image will move once per 2 minutes : Left
Right
Upside
Downside
Right
Left
Downside
Upside.
SCREEN
LOCK
PICTURE CONTROL
3
AUDIO
Press the G or
button and then use D or E or
or
button to select either Normal, White Wash,
Orbiter or Inversion.
Aspect Ratio
Aspect Ratio
Caption/Text
Caption Options
Language
ISM Method
Low Power
Set ID
G
Normal
White Wash
Orbiter
Inversion
2
3
Inversion
Inversion will automatically invert the plasma display
panel color every 30 minutes.
Press E X I T or R E T U R N button to return to TV viewing or press M E N U button to return to the previous
menu.
53
SOUND & LANGUAGE CONTROL
AUTO VOLUME LEVELER (EZ SOUNDRITE)
Scans for changes in sound levels during commercials, then
adjusts the sound to match the specified audio level.
SoundRite makes sure that the volume level remains consistent whether you are watching a commercial or a regular TV
program.
SETUP
VIDEO
1
Press the M E N U button and then use D or E or
or
button to select the A U D I O menu.
AUDIO
TIME
OPTION
Audio Language
EZ SoundRite
EZ Sound
Balance
0
TV Speakers
SCREEN
LOCK
SOUND & LANGUAGE CONTROL
54
2
Press the G or
button and then use D or E or
or
button to select E Z S o u n d R i t e.
1
3
button and then use D or E or
Press the G or
or
button to select O n or O f f.
SETUP
VIDEO
AUDIO
TIME
4
Press E X I T or R E T U R N button to return to TV viewing or press M E N U button to return to the previous
menu.
OPTION
Audio Language
EZ SoundRite
G
Balance
Off
On
EZ Sound
0
TV Speakers
SCREEN
LOCK
2
3
PRESET SOUND SETTINGS (EZ SOUND)
EZ Sound lets you enjoy the best sound without any special
adjustment because the TV sets the appropriate sound options
based on the program content.
Normal, Stadium, News, Music and Theater are preset for good
sound quality at the factory and are not adjustable.
1
■
Press E X I T or R E T U R N button to return to TV viewing.
You can also adjust E Z S o u n d in the AUDIO menu.
SETUP
VIDEO
AUDIO
TIME
OPTION
SETUP
Audio Language
VIDEO
EZ SoundRite
AUDIO
EZ Sound
TIME
Balance
TV Speakers
0
OPTION
SCREEN
SCREEN
LOCK
LOCK
Audio Language
EZ SoundRite
EZ Sound
Balance
TV Speakers
G
Normal
0
Stadium
SOUND & LANGUAGE CONTROL
2
Press the E Z S O U N D button repeatedly to select the
appropriate sound setup as below(Except 42PG60C,
42PG65C models):
N o r m a l, S t a d i u m, N e w s, M u s i c, T h e a t e r, and U s e r
(your own settings).
News
Music
Theater
User
55
SOUND &LANGUAGE CONTROL
SOUND SETTING ADJUSTMENT - USER MODE
Adjust the sound to suit your taste and room situations.
SETUP
VIDEO
1
Press the M E N U button and then use D or E or
or
button to select the A U D I O menu.
AUDIO
TIME
OPTION
Audio Language
EZ SoundRite
EZ Sound
Balance
0
TV Speakers
SCREEN
LOCK
2
Press the G or
button and then use D or E or
or
button to select E Z S o u n d.
1
3
button and then use D or E or
Press the G or
or
button to select U s e r.
SETUP
VIDEO
AUDIO
TIME
OPTION
4
SOUND & LANGUAGE CONTROL
Press the G or
button and then use D or E or
or
button to select the desired sound option
T r e b l e, B a s s, or F r o n t S u r r o u n d).
(T
Audio Language
Normal
EZ SoundRite
Stadium
EZ Sound
Balance
0
News
Music
TV Speakers
SCREEN
Theater
LOCK
User
G
2
5
Press the G or
button and then use F or G or
or
button to make appropriate adjustments.
Selecting the Front surround
button and then use F or G or
Press the G or
or
button to select O f f or 3 D E c h o S o u n d
S y s t e m.
6
Press E X I T or R E T U R N button to return to TV viewing or press M E N U button to return to the previous
menu.
3
SETUP
VIDEO
User
AUDIO
Treble
50
Bass
50
TIME
OPTION
Front Surround
G
Off
SCREEN
LOCK
4
SETUP
VIDEO
AUDIO
TIME
Front Surround
Off
OPTION
3D EchoSound System
Creates a stunning simulated stereo effect from any mono
sound and a realistic three-dimensional sound with a very
wide and deep sound stage.
SCREEN
LOCK
5
56
BALANCE ADJUSTMENT
Adjust the left/right sound of speaker to suit your taste and
room situations.
SETUP
1
VIDEO
Press the M E N U button and then use D or E or
or
button to select the A U D I O menu.
AUDIO
TIME
OPTION
Audio Language
EZ SoundRite
EZ Sound
Balance
0
TV Speakers
SCREEN
LOCK
SOUND & LANGUAGE CONTROL
2
Press the G or
button and then use D or E or
or
button to select B a l a n c e.
1
3
Press the G or
button and then use F or G or
or
button to make appropriate adjustments.
SETUP
VIDEO
AUDIO
TIME
OPTION
4
Press E X I T or R E T U R N button to return to TV viewing or press M E N U button to return to the previous
menu.
Audio Language
EZ SoundRite
EZ Sound
Balance
0
G
L
R
TV Speakers
SCREEN
LOCK
2
SETUP
VIDEO
AUDIO
TIME
OPTION
Audio Language
EZ SoundRite
EZ Sound
Balance
0
F
L
R
G
TV Speakers
SCREEN
LOCK
3
57
SOUND &LANGUAGE CONTROL
TV SPEAKERS ON/OFF SETUP
Turn the TV speakers off if using external audio equipment.
SETUP
1
Press the M E N U button and then use D or E or
or
button to select the A U D I O menu.
VIDEO
AUDIO
TIME
OPTION
Audio Language
EZ SoundRite
EZ Sound
Balance
0
TV Speakers
SCREEN
SOUND & LANGUAGE CONTROL
58
2
Press the G or
button and then use D or E or
or
button to select T V S p e a k e r s.
3
Press the G or
button and then use D or E or
or
button to select O n or O f f.
LOCK
1
SETUP
VIDEO
AUDIO
TIME
4
Press E X I T or R E T U R N button to return to TV viewing or press M E N U button to return to the previous
menu.
OPTION
SCREEN
Audio Language
EZ SoundRite
EZ Sound
Balance
TV Speakers
G
Off
On
LOCK
2
3
STEREO/SAP BROADCAST SETUP
This TV can receive MTS stereo programs and any SAP
(Secondary Audio Program) that accompanies the stereo program if the station transmits an additional sound signal as well
as the original one and when you select Stereo or SAP on the
remote control.
Mono sound is automatically received if the broadcast is only in
Mono; even though Stereo or SAP has been selected.
Select Mono if you want to listen to the mono sound in remote
areas during stereo/SAP broadcasting.
Stereo or SAP can be received in Analog channel.
1
Press E X I T or R E T U R N button to save and return to TV
viewing.
SOUND & LANGUAGE CONTROL
2
Use the S A P button to select your desired MTS mode in
analog signal. Each time you press the S A P button, M o n o,
S t e r e o, or S A P appear in turn.
■ If other languages available on the digital signal, select
them with the S A P button.
59
SOUND &LANGUAGE CONTROL
AUDIO LANGUAGE
Other languages may be available if a digital signal is provided
by the broadcasting station.
This feature operates only in DTV/CADTV mode.
SETUP
1
VIDEO
Press the M E N U button and then use D or E or
or
button to select the A U D I O menu.
AUDIO
TIME
OPTION
Audio Language
EZ SoundRite
EZ Sound
Balance
0
TV Speakers
SCREEN
LOCK
SOUND & LANGUAGE CONTROL
60
2
Press the G or
button and then use D or E or
or
button to select A u d i o L a n g u a g e.
1
3
Press the G or
button and then use D or E or
or
button to select: E n g l i s h, S p a n i s h, or
F r e n c h.
SETUP
VIDEO
AUDIO
TIME
Audio Language
EZ Sound
Balance
G
English
Spanish
French
TV Speakers
OPTION
SCREEN
4
Press E X I T or R E T U R N button to return to TV viewing or press M E N U button to return to the previous
menu.
LOCK
2
3
ON-SCREEN MENUS LANGUAGE SELECTION
The menus can be shown on the screen in the selected language. First select your language.
SETUP
1
Aspect Ratio
VIDEO
Press the M E N U button and then use D or E or
or
button to select the O P T I O N menu.
Caption/Text
AUDIO
Caption Options
TIME
Language
OPTION
ISM Method
SCREEN
Low Power
LOCK
Set ID
Press the G or
button and then use D or E or
or
button to select L a n g u a g e .
1
3
Press the G or
button and then use D or E or
or
button to select your desired language.
From this point on, the on-screen menus will be shown
in the selected language.
SETUP
VIDEO
AUDIO
TIME
OPTION
SCREEN
LOCK
4
Press the E X I T or R E T U R N button to return to TV
viewing or press M E N U to return to the previous
menu.
Aspect Ratio
Caption/Text
Caption Options
Language
ISM Method
Low Power
G
English
Spanish
French
Set ID
2
3
SOUND & LANGUAGE CONTROL
2
61
SOUND &LANGUAGE CONTROL
CAPTION / TEXT
Analog Broadcasting System Captions
Select a caption mode for displaying captioning information if provided on a
program. Analog caption displays information at any position on the screen and
is usually the program's dialog.
Text displays information, usually at the bottom position and is used for a data
service, generally not program related.
Caption/Text, if provided by the broadcaster, would be available for both digital
and analog channels on the Antenna/Cable.
This TV is programmed to memorize the caption/text mode which was last set
when you turn the power off.
When you select the CC1 ~ Text4, Caption options must be disabled.
1
Use the C C button repeatedly to select Caption O f f, C C 1, C C 2, C C 3,
C C 4, T e x t 1, T e x t 2, T e x t 3 or T e x t 4.
SOUND & LANGUAGE CONTROL
CAPTION
The term for the words that scroll across the bottom of the TV screen; usually the audio portion of the program provided for the hearing impaired.
■ TEXT
The term for the words that appear in a large black frame and almost cover
the entire screen; usually messages provided by the broadcaster.
■
2
■
Press E X I T or R E T U R N to save and return to TV viewing.
T e x t.
You can also use the O P T I O N menu to select C a p t i o n/T
SETUP
VIDEO
AUDIO
TIME
Aspect Ratio
Caption/Text
Caption Options
Language
OPTION
SCREEN
ISM Method
Low Power
LOCK
Set ID
62
SETUP
VIDEO
AUDIO
TIME
OPTION
SCREEN
LOCK
Aspect Ratio
Caption/Text
Caption Options
Language
ISM Method
Low Power
Set ID
G
Off
CC1
CC2
CC3
CC4
Text1
Text2
Text3
Text4
Digital Broadcasting System Captions
Choose the language you want the DTV/CADTV Captions
to appear in.
Other Languages can be chosen for digital sources only if
they are included on the program.
SETUP
1
VIDEO
Press the M E N U button and then use D or E or
or
button to select the O P T I O N menu.
AUDIO
TIME
Aspect Ratio
Caption/Text
Caption Options
Language
OPTION
SCREEN
Low Power
LOCK
Press the G or
button and then use D or E or
T e x t.
or
button to select C a p t i o n/T
Set ID
1
3
Press the G or
button and then use D or E or
or
button to select available caption languages:
E n g l i s h, S p a n i s h, or F r e n c h.
SETUP
VIDEO
AUDIO
TIME
OPTION
4
Press E X I T or R E T U R N button to return to TV viewing or press M E N U button to return to the previous
menu.
SCREEN
LOCK
Aspect Ratio
Caption/Text
Caption Options
Language
ISM Method
G
Off
English
Spanish
French
Low Power
Set ID
2
3
SOUND & LANGUAGE CONTROL
2
ISM Method
63
SOUND &LANGUAGE CONTROL
CAPTION OPTIONS
Customize the DTV/CADTV captions that appear on your
screen.
SETUP
VIDEO
Press the M E N U button and then use D or E or
or
button to select the O P T I O N menu.
1
AUDIO
TIME
Aspect Ratio
Caption/Text
Caption Options
Language
OPTION
SCREEN
ISM Method
Low Power
LOCK
Set ID
SOUND & LANGUAGE CONTROL
Press the G or
button and then use D or E or
or
button to select C a p t i o n O p t i o n s.
2
1
Press the G or
button and then use D or E or
or
button to select C u s t o m.
3
SETUP
VIDEO
AUDIO
Press the G or
button and then use D or E or
or
button to customize the S t y l e, F o n t, etc.,
to your preference.
A preview icon is provided at the bottom of the
screen, use it to see the caption language.
4
S i z e: Set the word size.
G F o n t: Select a typeface for the text.
G Text Color: Choose a color for the text.
G Text Opacity: Specify the opacity for the text color.
G B g (Background) C o l o r: Select a background color.
G B g (Background) O p a c i t y: Select the opacity for the
background color.
G Edge Type: Select an edge type.
G Edge Color: Select a color for the edges.
TIME
Aspect Ratio
Caption/Text
Caption Options
G
OPTION
SCREEN
LOCK
Set by Program
Custom
Language
ISM Method
Low Power
Set ID
G
5
64
Press E X I T or R E T U R N button to return to TV viewing or press M E N U button to return to the previous
menu.
2
3
SETUP
VIDEO
Size
AUDIO
Font
Font 0
Text Color
White
TIME
F
A Standard
OPTION
Text Opacity
Solid
SCREEN
Bg Color
Black
LOCK
Bg Opacity
Solid
Edge Type
None
Edge Color
Black
G
4
TIME SETTING
CLOCK SETTING
Auto Clock Setup
The time is set automatically from a digital channel signal.
The digital channel signal includes information for the
current time provided by the broadcasting station.
Set the clock manually if the current time is set incorrectly
by the auto clock function.
The factory default value of the Auto Clock is Off, because
a clock information sent each broadcasting station is different.
1
Press the M E N U button and then use D or E or
or
button to select the T I M E menu.
SETUP
Auto Clock
VIDEO
Manual Clock
AUDIO
Off Timer
TIME
On Timer
2
4
Auto Off
SCREEN
LOCK
Press the G or
button and then use D or E or
or
button to select O n.
Press the G or
button and then use D or E or
or
button to select your viewing area time zone
U.S.A : Eastern, Central, Mountain, Pacific, Alaska or
Hawaii.
Canada : Eastern, Central, Mountain, Pacific,
New F.land or Atlantic.
5
button and then use D or E or
Press the G or
or
button to select A u t o, O f f, O n, depending on
whether or not your viewing area observes Daylight
Saving time.
6
Press E X I T or R E T U R N button to return to TV viewing or press M E N U button to return to the previous
menu.
1
SETUP
Auto Clock
VIDEO
Manual Clock
G
Off
On
TIME SETTING
3
OPTION
Press the G or
button and then use D or E or
or
button to select A u t o C l o c k.
AUDIO
Off Timer
TIME
Time Zone
On Timer
OPTION
SCREEN
Auto Off
Eastern
Daylight Savings
Auto
LOCK
2
3
4
5
65
TIME SETTING
Manual Clock Setup
If the current time setting is wrong, reset the clock manually.
SETUP
1
Press the M E N U button and then use D or E or
or
button to select the T I M E menu.
Auto Clock
VIDEO
Manual Clock
AUDIO
Off Timer
TIME
On Timer
OPTION
Auto Off
SCREEN
2
Press the G or
button and then use D or E or
or
button to select M a n u a l C l o c k.
3
Press the G or
button and then use F or G or
or
to select either the year, date, or time option.
or
button to
Once selected, use the D or E or
set the year, date, and time option.
LOCK
1
TIME SETTING
SETUP
VIDEO
AUDIO
TIME
OPTION
SCREEN
4
Press E X I T or R E T U R N button to return to TV viewing or press M E N U button to return to the previous
menu.
LOCK
Auto Clock
Manual Clock
G
Year
----
Off Timer
On Timer
Auto Off
Date
-Time
--
/
--
:
--
--
2
66
3
AUTO ON/OFF TIMER SETTING
The timer function operates only if the current time has
been set.
The Off-Timer function overrides the On-Timer function if
they are both set to the same time.
The TV must be in standby mode for the On-Timer to work.
If you do not press any button within 2 hours after the TV
turns on with the On Timer function, the TV will automatically
revert to standby mode.
1
Press the M E N U button and then use D or E or
or
button to select the T I M E menu.
SETUP
Auto Clock
VIDEO
Manual Clock
AUDIO
Off Timer
TIME
On Timer
OPTION
Press the G or
button and then use D or E or
or
button to select O f f T i m e r or O n T i m e r.
3
Press the G or
button and then use D or E or
or
button to select O n.
■ To cancel the O n / O f f t i m e r function, select O f f.
LOCK
1
SETUP
VIDEO
AUDIO
4
button and then use D or E or
Press the G or
or
button to set the hour.
Auto Off
SCREEN
TIME
OPTION
Auto Clock
Manual Clock
Off Timer
On Timer
Auto Off
G
Off
On
SCREEN
6 : 30 AM
LOCK
5
Press the G or
button and then use D or E or
or
button to set the minutes.
2
6
TIME SETTING
2
3
4
5
Press E X I T or R E T U R N button to return to TV viewing or press M E N U button to return to the previous
menu.
67
TIME SETTING
AUTO SHUT-OFF SETTING
If set to on and there is no input signal, the TV turns off
automatically after 10 minutes.
SETUP
1
Auto Clock
VIDEO
Press the M E N U button and then use D or E or
or
button to select the T I M E menu.
Manual Clock
AUDIO
Off Timer
TIME
On Timer
OPTION
Auto Off
SCREEN
2
LOCK
Press the G or
button and then use D or E or
or
button to select A u t o O f f.
1
TIME SETTING
3
Press the G or
button and then use D or E or
or
button to select O n or O f f.
SETUP
Auto Clock
If set to On and there is
Manual Clock
no input signal, the TV
VIDEO
AUDIO
turns automatically
Off Timer
4
after 10 minutes.
TIME
Press E X I T or R E T U R N button to return to TV viewing or press M E N U button to return to the previous
menu.
On Timer
OPTION
SCREEN
Auto Off
G
Off
On
LOCK
2
68
3
SLEEP TIMER SETTING
The Sleep Timer turns the TV off at the preset time.
Note that this setting is cleared when the TV is turned off.
1
Press the T I M E R button repeatedly to select the number of
minutes. First the O f f option appears on the screen, followed
by the following sleep timer options: 10, 20, 30, 60, 90,
120, 180, and 240 minutes.
When the number of minutes you want is displayed on the
screen, press the E N T E R button. The timer begins to count
down from the number of minutes selected.
3
To check the remaining minutes before the TV turns off, press
the T I M E R button once.
4
To cancel the Sleep Timer, press the T I M E R button repeatedly
to select O f f.
TIME SETTING
2
69
SCREEN ADJUSTMENT
AUTO CONFIGURE (RGB [PC] MODE ONLY)
Automatically adjusts picture position and minimizes image
shaking.
Although the image is still not correct, your set is functioning
properly but needs further adjustment.
SETUP
1
VIDEO
Press the M E N U button and then use D or E or
or
button to select the S C R E E N menu.
AUDIO
TIME
Auto config.
Manual config.
XGA Mode
Reset
OPTION
SCREEN
LOCK
2
Press the G or
button and then use D or E or
or
button to select A u t o c o n f i g ..
1
SCREEN ADJUSTMENT
3
button to start A u t o c o n f i g ..
SETUP
When A u t o c o n f i g . has finished, O K will be
shown on screen.
■ If the position of the image is still not correct, try
Auto adjustment again.
■
VIDEO
AUDIO
TIME
Auto config.
G
To set
Manual config.
XGA Mode
Reset
OPTION
SCREEN
LOCK
4
5
70
Press the G or
If the picture needs to be adjusted more after Auto
adjustment in RGB (PC), you can adjust the M a n u a l
c o n f i g ..
Press the E X I T or R E T U R N button to return to TV
viewing or press the M E N U button to return to the
previous menu.
2 3
MANUAL CONFIGURE
If the picture isn’t clear after auto adjustment and especially if characters are still trembling, adjust the picture phase
manually.
This function works in the following mode: RGB-PC, RGB-DTV,
Component 480p/720p/1080i, HDMI 480p/720p/1080i.
The Phase, Clock functions work in the following mode:
RGB-PC mode.
1
Press the M E N U button and then use D or E or
or
button to select the S C R E E N menu.
SETUP
VIDEO
AUDIO
2
TIME
Press the G or
button and then use D or E or
or
button to select M a n u a l c o n f i g ..
Auto config.
Manual config.
XGA Mode
Reset
OPTION
SCREEN
LOCK
3
Press the G or
button and then use D or E or
or
button to select P h a s e, C l o c k, H - p o s i t i o n or V - p o s i t i o n.
■
4
Press the F or G or
priate adjustments.
or
5
Press the E X I T or R E T U R N button to return to TV
viewing or press the M E N U button to return to the
previous menu.
SETUP
VIDEO
AUDIO
TIME
OPTION
Auto config.
Manual config.
Phase
0
XGA Mode
Clock
0
Reset
H-Position
0
V-Position
0
G
SCREEN
LOCK
SCREEN ADJUSTMENT
Phase
This function allows you to remove any horizontal
noise and clear or sharpen the image of characters.
■ Clock
This function is to minimize any vertical bars or
stripes visible on the screen background. And the
horizontal screen size will also change.
■ H-position / V-position
This function is to adjust picture to left/right and
up/down as you prefer.
1
2 3 4
button to make appro-
71
SCREEN ADJUSTMENT
SELECTING XGA MODE
To see a normal picture, match the resolution of RGB mode and
selection of XGA mode.
This function works in the following mode: RGB-PC mode.
If you select the 1600x1200, 1920x1200 resolution, u X G A
m o d e is displayed.
SETUP
VIDEO
1
Press the M E N U button and then use D or E or
or
button to select the S C R E E N menu.
AUDIO
TIME
Auto config.
Manual config.
XGA Mode
Reset
OPTION
SCREEN
LOCK
2
Press the G or
button and then use
or
button to select X G A m o d e.
D
or E or
1
SCREEN ADJUSTMENT
3
Press the G or
button and then use D or E or
or
button to select the desired XGA resolution.
SETUP
VIDEO
AUDIO
TIME
OPTION
4
Press E X I T or R E T U R N button to return to TV viewing or press M E N U button to return to the previous
menu.
SCREEN
LOCK
Auto config.
Manual config.
XGA Mode
Reset
G
1024 x 768
1280 x 768
1360 x 768
1366 x 768
2 3
72
INITIALIZING
(RESET TO ORIGINAL FACTORY SETTINGS)
This function operates in current mode.
To initialize the adjusted value.
SETUP
1
VIDEO
Press the M E N U button and then use D or E or
or
button to select the S C R E E N menu.
AUDIO
TIME
Auto config.
Manual config.
XGA Mode
Reset
OPTION
SCREEN
LOCK
2
Press the G or
button and then use
or
button to select R e s e t.
D
or E or
1
3
Press the G or
button.
SETUP
AUDIO
TIME
Auto config.
Manual config.
XGA Mode
Reset
G
To set
OPTION
SCREEN
LOCK
2 3
SCREEN ADJUSTMENT
VIDEO
73
PARENTAL CONTROL / RATINGS
Parental Control can be used to block specific channels, ratings and other viewing sources.
The Parental Control Function (V-Chip) is used to block program viewing based on the ratings
sent by the broadcasting station. The default setting is to allow all programs to be viewed.
Viewing can be blocked by choosing the type of the program and the categories. It is also possible to block all program viewing for a time period. To use this function, the following must be
done:
1. Set ratings and categories to be blocked.
2. Specify a password
3. Enable the lock
V-Chip rating and categories
Rating guidelines are provided by broadcasting stations. Most television programs and television
movies can be blocked by TV Rating and/or Individual Categories. Movies that have been shown
at the theaters or direct-to-video movies use the Movie Rating System (MPAA) only.
Ratings for Television programs including made-for-TV movies:
TV-G
■ TV-PG
■ TV-14
■
(General audience)
(Parental guidance suggested)
(Parents strongly cautioned)
PARENTAL CONTROL / RATING
SET PASSWORD & LOCK SYSTEM
Setting up your password
Set up blocking schemes to block specific channels, ratings, and
external viewing sources.
A password is required to gain access to this menu.
1
Press the M E N U button and then use the D or E or
or
button to select the L O C K menu. Then, press the G
or
button.
Enter the password as requested.
■ The TV is set up with the initial
password “0-0-0-0”.
■
74
TV-MA (Mature audience only)
(All children)
■ TV-Y
■ TV-Y7 (Children 7 years older)
■
Enter
Password
Enter
Password
*
*
*
*
Set Password
Change the password by inputting a new password twice.
For USA
SETUP
After inputting the password, use the D or E or
or
button to choose S e t p a s s w o r d.
1
VIDEO
AUDIO
TIME
OPTION
Press the G or
button and then choose any 4
digits for your new password.
As soon as the 4 digits are entered, re-enter the same
4 digits on the C o n f i r m.
Then your changed password has been memorized.
2
Press E X I T or R E T U R N to return to TV viewing or
press M E N U to return to the previous menu.
3
SCREEN
Set Password
Set Password
Block Channel
Block Channel
TV Rating-English
Movie Rating
TV Rating-French
TV Rating-Children
Aux. Block
TV Rating-General
Downloadable Rating
Aux. Block
Downloadable Rating
1
SETUP
VIDEO
AUDIO
OPTION
G
Lock System
Lock System
LOCK
TIME
NOTE
For Canada
SCREEN
LOCK
Lock System
Set Password
G
Block Channel
New
Confirm
* * * *
* * * *
Movie Rating
TV Rating-Children
TV Rating-General
Aux. Block
Downloadable Rating
If you ever forget your password, key in ‘7’, ‘7’, ‘7’, ‘7’
on the remote control.
2
Lock System
Enables or disables the blocking scheme you set up previously.
For USA
SETUP
AUDIO
TIME
1
After inputting the password, use the D or E or
or
button to choose L o c k S y s t e m.
OPTION
SCREEN
SETUP
Lock System
VIDEO
Set Password
AUDIO
Block Channel
Lock System
Set Password
Block Channel
TIME
Movie Rating
TV Rating-English
OPTION
TV Rating-French
SCREEN
Aux. Block
TV Rating-Children
TV Rating-General
LOCK
LOCK
Aux. Block
Downloadable Rating
Downloadable Rating
2
Press the G or
button and then use the D or E
or
or
button to select O n or O f f.
1
■
When you select O n, the Lock System is enable.
SETUP
VIDEO
3
Press E X I T or R E T U R N button to return to TV viewing or press M E N U button to return to the previous
menu.
AUDIO
TIME
OPTION
SCREEN
LOCK
Lock System
G
Set Password
Off
On
Block Channel
PARENTAL CONTROL / RATING
VIDEO
For Canada
Movie Rating
TV Rating-Children
TV Rating-General
Aux. Block
Downloadable Rating
2
75
PARENTAL CONTROL /RATINGS
CHANNEL BLOCKING
Blocks any channels that you do not want to watch or that
you do not want your children to watch.
For USA
SETUP
VIDEO
AUDIO
TIME
1
After inputting the password, use the D or E or
or
button to choose B l o c k C h a n n e l.
OPTION
SCREEN
For Canada
Lock System
Lock System
Set Password
Set Password
Block Channel
Block Channel
TV Rating-English
Movie Rating
TV Rating-French
TV Rating-Children
Aux. Block
TV Rating-General
LOCK
Downloadable Rating
Aux. Block
2
Downloadable Rating
Press the G or
button. You will now see a screen
filled with channel numbers and a preview picture.
1
3
Use D E F G or
button to select a
channel and then use the E N T E R button to block or
unblock it.
SETUP
VIDEO
AUDIO
TIME
OPTION
4
Press E X I T or R E T U R N button to return to TV viewing or press M E N U button to return to the previous
menu.
SCREEN
LOCK
Lock System
Set Password
Block Channel
G
Movie Rating
Off
On
TV Rating-Children
TV Rating-General
Aux. Block
Downloadable Rating
1
2
EXTERNAL INPUT BLOCKING
For USA
Enables you to select a source to block from the external
source devices you have hooked up.
SETUP
VIDEO
AUDIO
TIME
PARENTAL CONTROL / RATING
OPTION
SCREEN
For Canada
Lock System
Lock System
Set Password
Set Password
Block Channel
Block Channel
TV Rating-English
Movie Rating
TV Rating-French
TV Rating-Children
Aux. Block
TV Rating-General
LOCK
Downloadable Rating
Aux. Block
1
After inputting the password, use the D or E or
or
button to choose A u x . B l o c k.
2
Press the G or
button and then use the F or G
or
or
button to select a source.
Downloadable Rating
1
SETUP
VIDEO
AUDIO
3
Press the G or
button and then use the D or E
or
or
button to select O n or O f f on the
each source.
TIME
Lock System
Set Password
Block Channel
Movie Rating
AV1
TV Rating-Children
AV2
On
TV Rating-General
Component
Off
RGB
Off
OPTION
SCREEN
LOCK
Aux. Block
G
Downloadable Rating
4
76
Press E X I T or R E T U R N button to return to TV viewing or press M E N U button to return to the previous
menu.
On
HDMI1/DVI
On
HDMI2
Off
2
3
MOVIE & TV RATING
Movie Rating (MPAA) -for USA only
Blocks movies according to the movie ratings limits specified, so children cannot view
certain movies. You can set the ratings limit by blocking out all the movies with the
ratings above a specified level. Keep in mind that the movie ratings limit only applies
to movies shown on TV, not TV programs, such as soap operas.
SETUP
VIDEO
After inputting the password, use the D or E or
or
button to choose M o v i e R a t i n g.
1
AUDIO
TIME
OPTION
Press the G or
button and then use the D or E
or
or
button to select G , P G, P G - 1 3, R ,
N C - 1 7 or X .
■ G (General audiences)
■ PG (Parental guidance suggested)
■ PG-13 (Parents strongly cautioned)
■ R (Restricted)
■ NC-17 (No one 17 and under admitted)
■ X (Adult only)
■ Blocking Off (Permits all programs)
2
G
SCREEN
Movie Rating
TV Rating-Children
TV Rating-General
Downloadable Rating
1
SETUP
VIDEO
AUDIO
TIME
OPTION
SCREEN
LOCK
If you set PG-13: G and PG movies will be available,
PG-13, R, NC-17 and X will be blocked.
Lock System
Set Password
Block Channel
Movie Rating
G
TV Rating-Children
TV Rating-General
Aux. Block
Downloadable Rating
For USA
SETUP
VIDEO
TIME
OPTION
SCREEN
or
Lock System
Set Password
Block Channel
Movie Rating
TV Rating-Children
TV Rating-General
LOCK
Aux. Block
G
PG
PG-13
R
NC-17
X
Blocking Off
2
For Canada
Lock System
Set Password
Block Channel
TV Rating-English
TV Rating-French
Aux. Block
Downloadable Rating
Downloadable Rating
button and then use the D or E or
Press the G or
or
button to select D i m 0, D i m 1, D i m 2, or D i m 3.
2
1
SETUP
Press the
or
or
3
G
VIDEO
or
button and then use the D or E
button to select D 1 L 1, D 1 L 2, or D 1 L 3.
AUDIO
TIME
OPTION
4
Press E X I T or R E T U R N button to return to TV viewing
or press M E N U button to return to the previous menu.
SCREEN
LOCK
Lock System
Set Password
Block Channel
Movie Rating
TV Rating-Children
TV Rating-General
Downloadable Rating
Dim0
Dim1
Dim2
Dim3
PARENTAL CONTROL / RATING
Downloadable Rating
After inputting the password, use the D or E or
button to choose D o w n l o a d a b l e R a t i n g.
Block Channel
Aux. Block
AUDIO
1
Set Password
LOCK
Press E X I T or R E T U R N button to return to TV viewing or press M E N U button to return to the previous
menu.
3
Lock System
Aux. Block
Downloadable Rating G
NOTE
G
G
This function may become available in the future and
will be available only for digital channel signal.
This function operates only when TV has received
Region5 Rating data.
2
G
Based on rating table, your TV's OSD (On
Screen Display) may differ slightly from what
is shown in this manual.
77
PARENTAL CONTROL /RATINGS
TV Rating Children -for USA only
Prevents children from watching certain children's TV programs, according to
the ratings limit set. The children rating does not apply to other TV programs.
Unless you block certain TV programs intended for mature audiences in the TV
Rating - sub menu, your children can view those programs.
SETUP
VIDEO
AUDIO
TIME
OPTION
1
2
After inputting the password, use the D or E or
button to choose T V R a t i n g - C h i l d r e n.
SCREEN
or
Lock System
Set Password
Block Channel
Movie Rating
TV Rating-Children
TV Rating-General
LOCK
Aux. Block
Downloadable Rating
button and then use the D or E or
Press the G or
or
button to select A g e, or F a n t a s y V i o l e n c e.
button and then use the D or E or
Press the G or
or
button to select block options.
1
SETUP
VIDEO
AUDIO
Age (applies to TV-Y, TV-Y7)
■ Fantasy Violence (applies to TV-Y7)
■
TIME
OPTION
SCREEN
Lock System
Set Password
Block Channel
Movie Rating
TV Rating-Children
G
TV Rating-General
Age
Fantasy Violence
LOCK
3
Aux. Block
Press E X I T or R E T U R N button to return to TV viewing
or press M E N U button to return to the previous menu.
Downloadable Rating
2
TV Rating General -for USA only
Based on the ratings, blocks certain TV programs that you
and your family do not want to view.
SETUP
PARENTAL CONTROL / RATING
1
After inputting the password, use the D or E or
button to choose T V R a t i n g - G e n e r a l.
VIDEO
or
AUDIO
TIME
OPTION
2
button and then use the D or E or
Press the G or
or
button to select A g e, D i a l o g u e, L a n g u a g e,
S e x or V i o l e n c e.
button and then use the D or E or
Press the G or
or
button to select block options.
Age (applies to TV-G,TV-PG,TV-14,TV-MA)
■ Dialogue-sexual dialogue (applies to TV-PG,TV-14)
■ Language-adult language (applies to TV-PG,TV-14,TV-MA)
■ Sex-sexual situations (applies to TV-PG,TV-14,TV-MA)
■ Violence (applies to TV-PG,TV-14,TV-MA)
■
SCREEN
Press E X I T or R E T U R N button to return to TV viewing
or press M E N U button to return to the previous menu.
Set Password
Block Channel
Movie Rating
TV Rating-Children
TV Rating-General
LOCK
Aux. Block
Downloadable Rating
1
SETUP
VIDEO
AUDIO
TIME
OPTION
SCREEN
Lock System
Set Password
Block Channel
Movie Rating
TV Rating-Children
TV Rating-General
G
LOCK
Aux. Block
3
Lock System
Downloadable Rating
Age
Dialogue
Language
Sex
Violence
2
78
TV Rating English - for CANADA only
Prevents children from watching certain children's TV programs, according to
the ratings limit set. The children rating does not apply to other TV programs.
Unless you block certain TV programs intended for mature audiences in the TV
Rating - sub menu, your children can view those programs.
SETUP
VIDEO
AUDIO
TIME
OPTION
1
2
After inputting the password, use the D or E or
button to choose T V R a t i n g - E n g l i s h.
or
Set Password
Block Channel
TV Rating-English
TV Rating-French
Aux. Block
LOCK
Downloadable Rating
Press the G or
button and then use the D or E or
or
button to select E, C, C 8 +, G, P G, 1 4 +, 1 8 +,
or Blocking Off.
E(Exempt)
C(Children)
■ C8+(Children eight years and older)
■ G(General programming, suitable for all audiences)
■ PG(Parental Guidance )
■ 14+(Viewers 14 years and older)
■ 18+(Adult programming)
■ Blocking Off(Permits all programs)
■
1
SETUP
VIDEO
■
3
SCREEN
Lock System
AUDIO
TIME
OPTION
SCREEN
Lock System
Set Password
Block Channel
TV Rating-English
G
TV Rating-French
Aux. Block
LOCK
Downloadable Rating
E
C
C8+
G
PG
14+
18+
Blocking Off
2
Press E X I T or R E T U R N button to return to TV viewing
or press M E N U button to return to the previous menu.
TV Rating French - for CANADA only
Based on the ratings, blocks certain TV programs that you
and your family do not want to view.
After inputting the password, use the D or E or
button to choose T V R a t i n g - F r e n c h.
or
SETUP
VIDEO
AUDIO
TIME
2
button and then use the D or E or
Press the G or
or
button to select E, G, 8 ans+, 13 ans+, 16 ans+,
18 ans+, or Blocking Off.
■ E(Exempt)
■ G(General)
■ 8 ans+(General-Not convenient for little children)
■ 13 ans+(Not convenient for children of 13 years and
younger)
■ 16 ans+(Not convenient for children of 16 years and
younger)
■ 18 ans+(This programs is only for adults)
■ Blocking Off(Permits all programs)
OPTION
SCREEN
Press E X I T or R E T U R N button to return to TV viewing
or press M E N U button to return to the previous menu.
Set Password
Block Channel
TV Rating-English
TV Rating-French
Aux. Block
LOCK
Downloadable Rating
1
SETUP
VIDEO
AUDIO
TIME
OPTION
SCREEN
Lock System
Set Password
Block Channel
TV Rating-English
TV Rating-French
G
Aux. Block
LOCK
Downloadable Rating
3
Lock System
PARENTAL CONTROL / RATING
1
E
G
8 ans+
13 ans+
16 ans+
18 ans+
Blocking Off
2
79
APPENDIX
TROUBLESHOOTING
The operation does not work normally.
Check to see if there is any object between the product and the remote control
causing obstruction. Ensure you are pointing the remote control directly at the TV.
■ Ensure that the batteries are installed with correct polarity (+ to +, - to -).
■ Ensure that the correct remote operating mode is set: TV, VCR etc.
■ Install new batteries.
■
The remote control
doesn’t work
Power is suddenly
turned off
Is the sleep timer set?
■ Check the power control settings. Power interrupted.
■ No broadcast on station tuned with Auto off activated.
■
The video function does not work.
Check whether the product is turned on.
Try another channel. The problem may be with the broadcast.
■ Is the power cord inserted into wall power outlet?
■ Check your antenna direction and/or location.
■ Test the wall power outlet, plug another product’s power cord into the outlet
where the product’s power cord was plugged in.
■
■
No picture &No sound
Picture appears slowly
after switching on
■
This is normal, the image is muted during the product startup process. Please
contact your service center, if the picture has not appeared after five minutes.
Adjust Color in menu option.
■ Keep a sufficient distance between the product and the VCR.
■ Try another channel. The problem may be with the broadcast.
■ Are the video cables installed properly?
■ Activate any function to restore the brightness of the picture.
■
APPENDIX
No or poor color
or poor picture
Horizontal/vertical bars
or picture shaking
■
Check for local interference such as an electrical appliance or power tool.
Station or cable product experiencing problems, tune to another station.
Station signal is weak, reorient antenna to receive weaker station.
■ Check for sources of possible interference.
■
Poor reception on
some channels
Lines or streaks
in pictures
80
■
■
Check antenna (Change the direction of the antenna).
The audio function does not work.
Press the VOL or VOLUME button.
■ Sound muted? Press MUTE button.
■ Try another channel. The problem may be with the broadcast.
■ Are the audio cables installed properly?
■
Picture OK & No sound
No output from one
of the speakers
Unusual sound from
inside
the product
■
Adjust Balance in menu option.
■
A change in ambient humidity or temperature may result in an unusual noise
when the product is turned on or off and does not indicate a fault with the
product.
There is a problem in PC mode. (Only PC mode applied)
The signal is out of range
Vertical bar or stripe on
background &
Horizontal Noise &
Incorrect position
Adjust resolution, horizontal frequency, or vertical frequency.
Check the input source.
■
Work the Auto configure or adjust clock, phase, or H/V position. (Option)
■
Check the signal cable.
Reinstall the PC video card.
■
APPENDIX
Screen color is unstable
or single color
■
■
81
APPENDIX
MAINTENANCE
Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you can
enjoy your new TV.
Caution: Be sure to turn the power off and unplug the power cord before you begin any cleaning.
Cleaning the Screen
1
Here’s a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm
water and a little fabric softener or dish washing detergent. Wring the cloth until it’s almost dry, and then
use it to wipe the screen.
2
Make sure the excess water is off the screen, and then let it air-dry before you turn on your TV.
Cleaning the Cabinet
To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth.
■ Please be sure not to use a wet cloth.
■
Extended Absence
CAUTION
G
If you expect to leave your TV dormant for a long time (such as a vacation), it’s a good idea to unplug
the power cord to protect against possible damage from lightning or power surges.
PRODUCT SPECIFICATIONS
MODELS
Dimensions
(Width x Height
x Depth)
APPENDIX
Weight
42PG65C
(42PG65C-UA)
41.1 x 28.9 x12.1 inches
1044.4 x 735.4 x 308.0 mm
With stand
(Only 42PG65C)
Without stand
With stand (Only 42PG65C)
Without stand
MODELS
82
42PG60C
(42PG60C-UA)
41.1 x 26.7x 3.1 inches
1044.4 x680.5x 79.6mm
41.1 x 26.7x 4.2 inches
1044.4 x680.5x 107.6mm
55.1 pounds / 25.0 kg
61.2 pounds / 27.8 kg
55.1 pounds / 25.0 kg
32LG500H
(32LG500H-UA)
37LG500H
(37LG500H-UA)
42LG500H
(42LG500H-UA)
36.1 x 26.9 x 11.5 inches 40.4 x 28.8 x 11.5 inches
918.6 x 684.8 x 293.4 mm 1026.2 x 734.0 x 293.4 mm
Dimensions
(Width x Height
x Depth)
With stand
31.3 x 23.5 x 8.9 inches
797 x 597 x 227.3 mm
Without stand
31.3 x 21.9 x 3.9 inches
797 x 558.6 x 100.5 mm
36.1 x 24.9 x 3.4 inches
918.6 x 632.8 x 88 mm
40.4 x 27.0 x 4.4 inches
1026.2 x 687.9 x 111.8 mm
Weight
With stand
Without stand
21.6 pounds / 9.82 kg
18.3 pounds / 8.34 kg
41.6 pounds / 18.8 kg
35.2 pounds / 15.9 kg
49.1 pounds / 22.3 kg
43.2 pounds / 19.6 kg
PRODUCT SPECIFICATIONS
32LC5DC/S/B
(32LC5DC/S/B-UA)
32LC50C/S/B
(32LC50C/S/B-UA)
37LC5DC/1/B
(37LC5DC/1/B-UA)
37LC50C/B
(37LC50C/B-UA)
42LC5DC
(42LC5DC-UA)
42LC50C
(42LC50C-UA)
32LX5DC/S
(32LX5DC/S-UA)
32LX50C/S
(32LX50C/S-UA)
Width x Height x Depth
(inches/mm)
With Stand
31.8 x 23.9 x 9.8 inches
806.6 x 607.5 x 249.0 mm
31.8 x 21.7 x 3.8 inches
806.6 x 552.3 x 97.2 mm
Without Stand
33.7 pounds / 15.3kg
27.6 pounds / 12.5 kg
Weight (pounds / kg)
With Stand
Without Stand
Width x Height x Depth
(inches/mm)
With Stand
36.5 x 27.4 x 10.4 inches
926.8 x 695.8 x 264.6 mm
Without Stand
36.5 x24.8 x 4.2 inches
926.8 x 629.8 x 107.4 mm
Weight (pounds / kg)
With Stand
Without Stand
47.2 pounds / 21.4 kg
36.8 pounds / 16.7 kg
Width x Height x Depth
(inches/mm)
With Stand
40.7 x 29.6 x 11.6 inches
1033.1 x 750.7 x 294.2 mm
Without Stand
40.7 x 27.0x 4.3 inches
1033.1 x 686.5 x 110.2 mm
Weight (pounds / kg)
With Stand
Without Stand
61.3 pounds / 27.8 kg
47.2 pounds / 21.4 kg
Width x Height x Depth
(inches/mm)
With Stand
36.3 x 24.2 x 11.3 inches
922.0 x 615.0x 288.0 mm
Without Stand
36.3 x 21.5 x 3.9 inches
922.0 x 546.0 x 98.0 mm
Weight (pounds / kg)
With Stand
39.0 pounds / 17.7 kg
30.4 pounds / 13.8 kg
Without Stand
Width x Height x Depth
(inches/mm)
42PX8DC
(42PX8DC-UA)
Weight (pounds / kg)
With Stand
46.7 x 28.1 x 10.6 inches
1186.0 x 714.0 x 270.0 mm
Without Stand
46.7 x 25.7 x 3.9 inches
1186.0 x 654.0 x 99.0 mm
With Stand
72.5 pounds / 32.9 kg
55.6 pounds / 25.2 kg
Without Stand
Width x Height x Depth
(inches/mm)
With Stand
Without Stand
Weight (pounds / kg)
40.7 x 29.6 x 11.6 inches
1033.1 x 750.7 x 294.2 mm
40.7 x 27.0x 4.3 inches
1033.1 x 686.5 x 110.2 mm
61.3 pounds / 27.8 kg
47.2 pounds / 21.4 kg
With Stand
Without Stand
Power requirement
AC100-240V ~ 50/60Hz
Television System
NTSC-M, ATSC, 64 & 256 QAM
Program Coverage
VHF 2-13, UHF 14-69, CATV 1-135, DTV 2-69, CADTV 1-135
External Antenna Impedance
Operating Temperature Range
■
75 ohm
32 ~ 104°F (0 ~ 40°C)
Operating Humidity Range
Less than 80%
Storage Temperature Range
-4 ~ 140°F (-20 ~ 60°C)
Storage Humidity Range
APPENDIX
42LB5DC
(42LB5DC-UA)
42LB50C
(42LB50C-UA)
Less than 85%
The specifications shown above may be changed without prior notice for quality improvement.
83
APPENDIX
PROGRAMMING THE REMOTE CONTROL
The provided universal remote control can be programmed to operate most remote-controllable devices.
Note that the remote may not control all models of other brands.
Programming a code into a remote mode
1
To find out whether your remote control can operate each device without programming, turn on the device
(such as a VCR) and press the corresponding mode button on the remote.
After that, press the POWER button. If the device is turned off and it responds properly the remote control
need not be programmed. If not, the remote should be programmed to operate the device. The programming procedures are explained below.
2
Press the M E N U and M U T E button continuously at the same time for two seconds; the currently selected
device button is illuminated.
If you don't press any button for 20 seconds, the light on the mode button will be turned off. In that case,
you have to repeat from step 2.
3
Enter the appropriate code from the code table on the following pages. When pressing the button, the
light blinks at a time. If the device turned off, the programming is successful.
4
Press the M E N U button to store the code. After blinking twice, this code is stored.
5
Test the remote control functions to see if the device responds properly. If not, steps 2-5.
APPENDIX
Remote Control Code
DVD
Brand
Codes
APEX DIGITAL
022
DENON
020
GE
005
HARMAN KARDON
JVC
012
LG
001
MAGNAVOX
013
MARANTZ
024
84
014
006
027
010 016 025
Brand
Codes
Brand
Codes
MITSUBISHI
NAD
ONKYO
PANASONIC
PHILIPS
PIONEER
PROCEED
PROSCAN
002
023
008
003
013
004
021
005
RCA
SAMSUNG
SONY
THOMPSON
TOSHIBA
YAMAHA
ZENITH
005
011
007
005
019
009
010
017
009
026
006
006
015
006
008
018
016 025
VCR
Brand
AIWA
AKAI
Codes
Codes
Brand
MAGNAVOX
031 033 034 041
067 068
012 031 033 067
SAMSUNG
043 046 124
146
MARANTZ
069
033
023
037
031
103
039 043
129
033
MARTA
MATSUI
MEI
MEMOREX
040
033
007
108
116
135
041
010 064
110 111
117 119
MGA
MINOLTA
MITSUBISHI
101
027
031
003
033
101
045
013
013
049
151
034
024
012
048
043
053
066
133
023 039 043
053
017
031
037
131
008
025
034
046
138
009
033
109
136
012
018
063
033
033
013
066
063 072
144 147
031
050
150
034
048
012
106
027
035
101
153
010
045
026 034
137 150
015 033
101
033 043
055 060
152
039 043
MTC
MULTITECH
NEC
NORDMENDE
OPTONICA
PANASONIC
PENTAX
PHILCO
PHILIPS
PILOT
PIONEER
PORTLAND
PULSAR
QUARTZ
QUASAR
RCA
REALISTIC
013 020
114 123
009 013 014
034 101 106
RICO
RUNCO
SALORA
013
063
031
031
067
101
013
108
072
011
033
013
040
107
145
003
031
053
058
148
014
030
033
010
034
102
046
020
020
051
014 031
053 072
134 139
059
045 046
059 061
040
034
023 039 043
054
070 074 083
140 145
020 031 033
034 067
033 034 054
071 101
021 048
014
066
020
041
109
147
008
033
054
075
033
062
140
145
034
063
144
010 014
034 040
101
Codes
032
105
113
125
SANSUI
022
SANYO
003
102
SCOTT
017
131
SEARS
003
013
031
101
SHARP
031
SHINTOM
024
SONY
003
056
077
SOUNDESIGN
034
STS
013
SYLVANIA
031
067
SYMPHONIC
034
TANDY
010
TATUNG
039
TEAC
034
TECHNICS
031
TEKNIKA
019
101
THOMAS
034
TMK
006
TOSHIBA
008
059
TOTEVISION
040
UNITECH
040
VECTOR RESEARCH 012
VICTOR
048
VIDEO CONCEPTS 012
VIDEOSONIC
040
WARDS
003
031
053
YAMAHA
012
ZENITH
034
058
040 102 104
107 109 112
115 120 122
043 048 135
007 010 014
134
037 112 129
008 009 010
014 017 020
042 073 081
054 149
009 031 052
057 058 076
078 149
033 034 059
034
043
039 043
033 070
031 033 034
013 042 047
082 112 131
101
APPENDIX
034
016
125
AMPRO
072
ANAM
031
AUDIO DYNAMICS 012
BROKSONIC
035
CANON
028
CAPEHART
108
CRAIG
003
CURTIS MATHES 031
DAEWOO
005
065
112
DAYTRON
108
DBX
012
DYNATECH
034
ELECTROHOME 059
EMERSON
006
029
036
129
FISHER
003
FUNAI
034
GE
031
107
GO VIDEO
132
HARMAN KARDON
HITACHI
004
043
INSTANTREPLAY 031
JCL
031
JCPENNY
012
040
JENSEN
043
JVC
012
048
130
KENWOOD
014
047
LG (GOLDSTAR) 001
101
LLOYD
034
LXI
003
017
MAGIN
040
Brand
034 046
013
033
054
034
048
072
017
034
131
039
056
080
024
040
043
101
85
APPENDIX
SET ID
Use this function to specify a TV ID number.
SETUP
1
VIDEO
Press the M E N U button and then use D or E or
or
button to select the OPTION menu.
AUDIO
TIME
Aspect Ratio
Caption/Text
Caption Options
Language
OPTION
SCREEN
ISM Method
Low Power
LOCK
2
Press the G or
button and then use
or
button to select Set ID.
D
Set ID
or E or
1
3
Press the G or
button and then use D or E or
or
button to adjust Set ID to choose the
desired TV ID number. The adjustment range of Set ID
is 1~99.
SETUP
VIDEO
AUDIO
TIME
OPTION
4
APPENDIX
86
Press E X I T or R E T U R N button to return to TV viewing or press M E N U button to return to the previous
menu.
SCREEN
LOCK
Aspect Ratio
Caption/Text
Caption Options
Language
ISM Method
Low Power
Set ID
G
1
2
3
IR CODES
(Hexa)
Code
Function
Note
0F
TV INPUT
Remote control Button (Some models) D6
0B
INPUT
Remote control Button
08
POWER
Remote control Button (Power On/Off)
98
MULTI
Remote control Button (Some models)
79
RATIO
Remote control Button
0E
TIMER
Remote control Button
10-19
Number Key 0-9
Remote control Button
4C
- (Dash)
Remote control Button
1A
FLASH BACK
Remote control Button
09
MUTE
Remote control Button
02
VOL +
Remote control Button
03
VOL -
Remote control Button
00
CH + ,
Remote control Button
01
CH - ,
Remote control Button
39
CC
Remote control Button
40
D ,
Remote control Button
41
E
,
Remote control Button
07
F ,
Remote control Button
06
G ,
Remote control Button
Code
(Hexa)
C4
POWER ON
C5
POWER OFF
5A
D0
COMPONENT
D5
RGB-PC
CE
CC
77
Ratio 16:9
EXIT, RETURN
Remote control Button
0A
SAP
Remote control Button
PIP CH +
Remote control Button
61
PIP INPUT
Remote control Button
63
SWAP, PIP SWAP
Remote control Button
Discrete IR Code
Discrete IR Code
Discrete IR Code
(Only 16:9 Mode)
Ratio Zoom
Discrete IR Code
(Only Zoom1 Mode)
APPENDIX
71
Discrete IR Code
(Only 4:3 Mode)
5B
Remote control Button
HDMI2
Ratio 4:3
Remote control Button (Some models) AF
PIP CH -
HDMI1/DVI
76
EZ PIC
72
Discrete IR Code
(HDMI2 Input Selection)
4D
Remote control Button
Discrete IR Code
(HDMI1/DVI Input Selection)
Remote control Button (Some models)
Remote control Button
Discrete IR Code
(RGB-PC Input Selection)
EZ SOUND
INFO
Discrete IR Code
(Component Input Selection)
52
PIP
AV2
BF
Remote control Button
60
AV1
(AV2 Input Selection)
Remote control Button
AA
Discrete IR Code
(AV1 Input Selection)
ENTER
Remote control Button (Some models)
Discrete IR Code
(Only Power Off)
MENU
E0
Discrete IR Code
(Only Power On)
43
Remote control Button (Some models)
TV
Note
(TV Input Selection)
44
E1
Function
87