Owner`s manual | Bosch Appliances D1265 Home Security System User Manual

D1265
Owner's Manual
EN
Touchscreen Keypad
D1265 | Owner's Manual Contents
This system includes a telephone line seizure feature. The system might be programmed to
communicate with a central monitoring station to report system events. You cannot use your
phone while the system is communicating with the central monitoring station. In the unlikely
event that the central station is not able to receive the report, your phone might be
unavailable for up to 20 minutes while the control panel makes additional communication
attempts.
Some commands listed below might not be available. Contact your security company for
more information.
2
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
D1265 | Owner's Manual | Contents
Contents
Introduction.....................................................................6
Your Keypad.....................................................................6
Part I: Security System Basics......................................7
Using the keypad..............................................................7
Command ENTER buttons.............................................7
Points .................................................................................7
What is a Point .................................................................7
Controlled Points..............................................................7
24-Hour Points..................................................................7
Your Custom Display ......................................................9
View Faulted or Bypassed Points .................................10
To Scroll Faulted or Bypassed Points...........................10
Warning Displays and Tones ........................................10
Keypad Quiets for Button presses ................................10
Priority of Events............................................................10
Fire Alarms......................................................................11
Silencing Fire Alarms.....................................................11
Burglary Alarms .............................................................12
Silencing Burglary Alarms.............................................12
Fire Trouble and Fire Supervisory Events...................12
Silencing Fire Trouble and Fire Supervisory conditions
..........................................................................................12
Special Fire Trouble and Fire Supervisory Display....12
Viewing Fire Trouble and Fire Supervisory Conditions
..........................................................................................12
Non-Fire Trouble and Supervisory Events..................13
Silencing Non-Fire Trouble and Supervisory Events .13
Viewing Non-Fire Trouble Events ...............................13
Special System Trouble Display ...................................13
Events Cleared from the Keypad Are Not Lost..........13
Entry Delay Tone and Display .....................................13
Exit Delay Tone and Display........................................13
Button Press Checking Tones .......................................13
Silencing an Alarm.........................................................13
To Silence an alarm: ......................................................13
How Your System Reports Alarms ..............................14
Part II: System Commands.........................................15
Passcode Protected Commands and Functions...........16
Turning the System On (Arming).................................16
To Turn Your Security System On (Arm)...................16
Turning the System Off (Disarming)............................16
To Turn Your Security System Off (Disarm):.............16
Turning On the System (Arming) With a Duress
Passcode ..........................................................................17
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
Turning On the System (Arming) With Doors or
Windows Open .............................................................. 17
Master Arm (CMD + 1) ................................................ 19
Description...................................................................... 19
Using Master Arm ......................................................... 19
Master Arming all Areas ............................................... 20
Master Arm Instant (CMD + 1 + 1) ............................ 21
Perimeter Instant (CMD + 2) ....................................... 21
Turn On the Perimeter With No Delays..................... 21
Using Perimeter Instant................................................. 21
Perimeter Delay (CMD + 3) ......................................... 22
Turn On the Perimeter With Delays ........................... 22
Silence Trouble Sound/Clear Trouble Display (CMD
+ 4) .................................................................................. 23
Description...................................................................... 23
Using CMD 4 ................................................................. 23
View Alarm Memory (CMD + 4 + 0)......................... 23
Using View Alarm Memory ......................................... 23
Walk Test (CMD + 4 + 4) ............................................ 24
Reset Sensors (CMD + 4 + 7) ...................................... 25
Using Reset Sensors....................................................... 25
Watch Mode (CMD + 6) .............................................. 26
Using Watch Mode........................................................ 26
Entering Watch Mode ................................................... 26
Exiting Watch Mode: .................................................... 26
Perimeter Partial (CMD + 8) ........................................ 27
Partially Turn On the Perimeter .................................. 27
Using Perimeter Partial ................................................. 27
Special Alerts (CMD + 7 and CMD + 9).................... 28
Using CMD 7 ................................................................. 28
Using Command 9......................................................... 29
Part III: Advanced Commands................................. 30
Advanced Commands ................................................... 30
Bypass a Point (CMD + 0) ............................................ 31
Description...................................................................... 31
Using Bypass a Point ..................................................... 31
Unbypass A Point (CMD + 0 + 0)............................... 33
Description...................................................................... 33
Using Unbypass a Point ................................................ 33
Send Report (CMD + 4+1 or 4+2).............................. 34
Description...................................................................... 34
Using Send Report......................................................... 34
Remote Program (CMD + 4 + 3) ................................ 35
Description...................................................................... 35
For systems without a phone number.......................... 35
For systems with a phone number configured............ 36
For systems with a network connection....................... 36
3
D1265 | Owner's Manual | Contents
Change Time/Date (CMD + 4 + 5) .............................37
Door Control (CMD + 4 + 6).......................................39
Description ......................................................................39
Using Door Control .......................................................39
Access Level....................................................................41
Change Display (CMD + 4 + 9)...................................42
Show Continuous Time/Date .......................................42
Extend Closing (CMD + 5 + 1)....................................42
Chg Skeds (CMD + 5 + 2) ............................................44
Description ......................................................................44
Using Chg SKEDS .........................................................44
Delete User (CMD + 5 + 3) ..........................................46
Change Relay (CMD + 5 + 4) ......................................47
Change Passcode (CMD + 5 + 5).................................47
Description ......................................................................47
Using Change Passcode .................................................47
Add/Change User (CMD + 5 + 6)...............................48
Default Text (CMD + 5 + 7).........................................55
Fire Test (CMD + 5 + 8) ...............................................55
Display Rev (CMD + 5 + 9) .........................................57
Service Menu (9 + 9 + Enter) ......................................57
Using View Log..............................................................58
Using Print Log...............................................................58
Using Display Revision..................................................58
Using Service Walk Test................................................59
Using Default Text .........................................................59
Keypad Setup Menu ......................................................59
Part IV: Multi-Area Use..............................................60
Working with Multiple Areas from a Single Keypad .60
View Area Status ............................................................60
View Point Status ...........................................................61
Move To Area (CMD + 5 + 0).....................................62
Turning On the System .................................................62
Turning on Selected Areas ............................................62
Turning on Multiple Areas with a Passcode................63
Faulted Points in Other Areas.......................................63
Turn On the Entire System Without Delays ...............64
Turning on All or Selected Areas .................................64
Turning Off the System .................................................65
Turning Off Multiple Areas with a Passcode ..............65
Turning Off Multiple Areas with Disarm All..............65
Turning Off Selected Areas...........................................66
Appendix .......................................................................67
Supplementary Information for Adding Passcodes ....67
User Authority Levels ....................................................67
Passcode Worksheet.......................................................67
User Interface .................................................................67
User Interface .................................................................68
4
User (Passcode) Worksheet (User 000 to 038) ............ 69
 User (Token) Worksheet (User 000 to 038)
D9412GV3/D7412GV3/D9412GV2/D7412GV2 Only
......................................................................................... 70
User (Passcode) Worksheet (User 039 to 075) ............ 71
 User (Token) Worksheet (User 039 to 075)
D9412GV3/D7412GV3/D9412GV2/D7412GV2 Only
......................................................................................... 72
User (Passcode) Worksheet (User 076 to 114) (101-249
= D9412GV3/D9412GV2 only) .................................. 73
 User (Token) Worksheet (User 076 to 114)
D9412GV3/D7412GV3/D9412GV2/D7412GV2 Only
(101-249 = D9412GV3/D9412GV2 only)................... 74
User (Passcode) Worksheet (User 115 to 150) (101-249
= D9412GV3/D9412GV2 only) .................................. 75
User (Token) Worksheet (User 115 to 150) (101-249 =
D9412GV3/D9412GV2 only) ...................................... 76
User (Passcode) Worksheet (User 151 to 189) (101-249
= D9412GV3/D9412GV2 only) .................................. 77
User (Token) Worksheet (User 151 to 189) (101-249 =
D9412GV3/D9412GV2 only) ...................................... 78
User (Passcode) Worksheet (User 190 to 226) (101-249
= D9412GV3/D9412GV2 only) .................................. 79
 User (Token) Worksheet (User 190 to 226)
D9412GV3/D7412GV3/D9412GV2/D7412GV2 Only
(101-249 = D9412GV3/D9412GV2 only)................... 80
User (Passcode) Worksheet (User 227 to 249) (101-249
= D9412GV3/D9412GV2 only) .................................. 81
User (Token) Worksheet (User 227 to 249) (101-249 =
D9412GV3/D9412GV2 only) ...................................... 82
User (Passcode) Worksheet (Blank) ............................. 83
User (Token) Worksheet (Blank).................................. 84
Security System Limitations.......................................... 84
Fire Safety and Evacuation ........................................... 85
Standard Displays .......................................................... 86
System Trouble Displays............................................... 87
Security System Glossary .............................................. 89
Maintenance and Service .............................................. 90
How to Clean the Keypad ............................................ 90
Your Alarm Company .................................................. 90
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
D1265 | Owner's Manual | Figures
Figures
Figure 1:
Figure 2:
Figure 3:
Figure 4:
D1265 Touch Screen Numerical ...............6
Smoke Detector Locations (Plan View)..85
Smoke Detector Locations
(Elevation View)........................................85
Escape Route .............................................85
Tables
Table 1:
Table 2:
Table 3:
Table 4:
Table 5:
D1265 Keypad Buttons ..............................7
Keypad Commands ..................................15
Door Status ................................................39
Sked Table .................................................45
Screen Area Definitions ...........................61
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
5
D1265 | Owner's Manual | Introduction
Introduction
Your security system helps to secure life, property, and
investments against fire, theft, and bodily harm. The
D1265 Touchscreen Keypad is an SDI compatible
device that works with GV2/GV3 Series Control
Panels. Each keypad has an illuminated touchscreen to
display system messages and graphics buttons for data
or command entry, and a sounder that emits eight
warning tones.
Your Keypad
The D1265 keypad uses up to four rows of 20
characters each to display system messages and
graphical buttons used to select a menu and associated
functions. In addition to system messages and buttons,
the keypad shows, as needed, ten numerical buttons (0
to 9) and two function buttons (CMD and ENTER).
Use the CMD button in combination with numeric
buttons to perform a function. Use the ENTER button
to enter your passcode.
When several events occur, the keypad shows each
event in order of priority.
Figure 1: D1265 Touchscreen Numerical
6
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
D1265 | Owner's Manual | Part I: Security System Basics
Part I: Security System Basics
Using the keypad
Your security system provides quick access to functions
by pressing the CMD button and one or two additional
buttons.
Pressing the Previous or Next button while in the
Menu List allows you to scroll through the list of
functions enabled and programmed by your security
company.
Pressing press the button for the function you wish to
perform.
Another way to access functions is through the
function list. To access the function list, press the
Menu button.
To exit the function list, press the Exit button.
Use the function list to locate functions you don’t use
often or that don’t have a command number.
Command ENTER buttons
Table 1: D1265 Keypad Buttons
Button
Name
Description
CMD
Use the CMD button in combination with one or two numeric buttons to perform
a function.
ENTER
The ENTER button is used to complete the entry of your passcode at the keypad.
Whenever a function requires that you enter your passcode at the keypad, first
press the digits of the code and then press the ENTER button. Your system will
not recognize your passcode until you press ENTER.
When the Exit button appears in the keypad display, pressing it brings you one
level up in the function or exits you from the function you are in. These functions
might be shown on either side of the display.
When viewing a list, pressing the Previous button takes you back to the
previously shown item.
Press the Next button to pass over the present item(s) in a menu or function.
Exit
Previous
Next
Points
What is a Point
A “point” is a detection device, or group of devices
connected to your security system. Points display
individually at the keypad with custom text. The text
can describe a single door, motion sensor, smoke
detector, or an area such as UPSTAIRS or GARAGE.
There are two basic types of points, controlled and
24-hour.
Controlled Points
Controlled points respond to alarm conditions
depending upon whether the system is turned on
(armed) or turned off (disarmed). Controlled points are
programmed to respond instantly to alarm conditions
or to provide a delay for you to reach the keypad and
disarm the system.
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
The type of alarm appears before the point text when
there is an alarm. There are two types of controlled
points, perimeter points and interior points.
Perimeter Points
These points usually include all exterior doors and
windows of the building.
Interior Points
These points usually include interior forms of burglary
detection devices, such as motion sensors, or inside
doors, for example.
24-Hour Points
24-hour points are always on, even when the burglary
system is disarmed (turned off). There are two types of
24-hour points, fire points and non-fire points.
7
D1265 | Owner's Manual | Part I: Security System Basics
Fire Points
Fire points exclusively monitor fire detection devices.
They are always armed and cannot be disarmed. You
can clearly distinguish fire points from other non-fire
points at the keypad.
When there is a fire alarm, the display shows the
following:
*FIRE ALARM* is shown on the first line, text
identifying the point as a fire point is shown on the
second line, and instructions for silencing the alarm are
shown on the third and fourth lines.
Fire alarms have a unique audible warning signal.
Non-Fire Points
Non-fire 24-hour points are always armed and cannot
be disarmed.
8
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
D1265 | Owner's Manual | Part I: Security System Basics
Your Custom Display
“At an idle state” means that the system is not currently performing a function entered by a user. There are three
idle states the system might be in:
 Turned on (Armed)
 Turned off (Disarmed) with no points faulted (doors or windows open) in the area
 Turned off with faulted points (doors or windows open) in the area. This manual uses the default idle state
shows for examples of these idle states. Your security company might have programmed custom text for the
idle shows in your system. The custom text and the default text for the three system idle displays follow.
Default Text
Area Name Text
Appears on the top line of the display
and is customizable using Remote
Programming Software (RPS)
Custom Text
________________
Throughout this manual, all examples of “AREA # NAME TEXT” use “AREA 1 WAREHOUSE.” The
actual name of Area 1 differs depending on the specifics of your system.
Area Is On Text
________________
Area Off Text
Indicates the area is turned off
(disarmed). 24-hour points remain
armed.
________________
Area Not Ready Text
Indicates that the area is turned off,
but not ready to arm.
________________
The Silence button only appears if the trouble tone is sounding.
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
9
D1265 | Owner's Manual | Part I: Security System Basics
View Faulted or Bypassed Points
Warning Displays and Tones
To properly arm your system, all the exterior points
(doors and windows) and interior points (motion
sensors, inside doors, and so on) in the system must be
in the normal (not faulted) condition. Viewing the
faulted points helps you find faulted points (such as
doors or windows that are left open) and correct them
so proper arming is possible.
Your keypad emits one of several distinct tones and
displays custom text to alert you to system events.
Additional bells or sirens might also be connected to
your system. Bells or sirens mounted on the exterior of
your premises alert neighbors to emergencies and
provide an audible guide for police and fire fighters.
Your keypad offers a way of displaying faulted and
bypassed point information.
Pressing any button on the keypad quiets any warning
tones. If you don’t press another button within 7 sec,
the warning tones resume.
To Scroll Faulted or Bypassed Points
1. Ensure your keypad shows idle text.
2.
3.
4.
5.
10
Press the View Points button to show the first
faulted point.
Press the Next button or the Previous button
repeatedly to show the faulted and bypassed
point information.
If faulted or bypassed points in other areas exist,
then the display indicates the Area number and
the number of faulted/bypassed points before
returning to idle text.
If there are no faulted or bypassed points in
other areas, the display returns to idle text.
Keypad Quiets for Button presses
Priority of Events
If more than one event occurs, your system sorts them
into one of four groups. The groups (highest priority
first) are:
1. Fire Alarms
2. Burglary Alarms
3. Fire Troubles and Fire Supervisory conditions
4. Non-Fire Troubles and Non-Fire Supervisory
conditions
The group with the highest priority scrolls first in the
keypad’s display. Descriptions of the tones and
displays for each group and instructions for silencing
the tones are included in the descriptions that follow.
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
D1265 | Owner's Manual | Part I: Security System Basics
Fire Alarms
Fire alarms are the highest priority events. When a fire
point activates, your keypad emits a pulsating highpitched fire tone. Evacuate all occupants and
investigate for smoke or fire. Ensure that all occupants
know the difference between the burglary tone and the
fire tone. The tone sounds for the time set by your
security company.
The keypad display shows the point text of the first
point that went into fire alarm and shows the message
Enter Passcode and ENTER key to silence.
The display shows the instructions for clearing the
message. Enter a valid passcode and press the Clear
button.
If a fire trouble still exists, the *Alarm Silenced*
display will not be cleared. To remove this display, the
fire point(s) must be returned to normal.
If you have not cleared the *Alarm Silenced* display
and wish to review cleared events, use CMD 40.
Silencing Fire Alarms
Entering a personal passcode with the proper authority
level silences a fire alarm and disarms the system if it
was armed.
The system now shows *Alarm Silenced* and then
the number of points in alarm (# FIRE ALARMS) and
then the area text appears (AREA 1 NAME TEXT)
followed by the custom text of all the points in alarm
(for example, SMOKE DETECTOR), in the order of
occurrence.
If there is more than one point causing an alarm, the
display shows each point for 3 sec before showing the
next one.
When the last alarm is shown, the next display is the
first alarm.
Your system might be programmed so that you cannot
silence some fire alarms until the fire event clears.
The *Alarm Silenced* message continues to alternate
with idle text as a reminder that it is still possible to
view the text of the points in alarm by using the View
Alarm Memory function (refer to View Alarm Memory
(CMD + 4 + 0) on page 23 for more information.
To clear the event memory and remove the *Alarm
Silenced* message from the display, press the Clear
Display button.
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
11
D1265 | Owner's Manual | Part I: Security System Basics
Burglary Alarms
Fire Trouble and Fire Supervisory Events
Burglary alarms are the second priority. When a
burglary point activates while your system is armed,
your keypad emits a steady high-pitched burglary tone.
The tone sounds for the time set by your security
company.
When a fire trouble or fire supervisory condition
occurs, your keypad emits three warble tones, then a
pause (repeatedly).
The keypad display shows the number of burglary
points activated, the message Enter Passcode to
silence alarm and then custom text for each activated
point.
The system shows the number of fire points that are in
a trouble or supervisory condition as well as the point
text of the affected points.
Silencing Fire Trouble and Fire Supervisory
conditions
If there is more than one point causing an alarm, the
display shows each point for 3 sec before showing the
next one. When the last alarm is shown, the next
display is the first alarm.
Silencing Burglary Alarms
Entering a personal passcode with the proper authority
level silences a burglary alarm and disarms the system
if it was armed.
The system now shows *Alarm Silenced* and then
the number of points in alarm (### ALARMS) and
the custom text of all the points in alarm, in ascending
numeric order by area.
Pressing CMD 4 or the Silence button silences and
clears the Fire Trouble and/or the Fire Supervisory
conditions.
In addition to this, entering a personal passcode with
the proper authority level silences a fire trouble and
disarms the control panel if it was armed. Use CMD
40 if you wish to review these cleared troubles.
Some systems might be programmed to
automatically re-sound the keypad’s
trouble tone after a period of time if the
fire trouble or fire supervisory condition
remains. Consult your security company
for further information.
Special Fire Trouble and Fire Supervisory Display
If you silence the keypad or clear a trouble or
supervisory condition for a Fire Point from the display
and the fire point remains faulted, Fire Trouble
appears in the keypad’s display.
Entering CMD 4 clears the scrolling point text from
the display.
The *Alarm Silenced* message continues to alternate
with idle text as a reminder that it is still possible to
view the text of the points in alarm by using the View
Alarm Memory function (refer to View Alarm Memory
(CMD + 4 + 0) on page 23 for more information).
To clear the event memory and remove the *Alarm
Silenced* message from the display, press the Clear
Display button.
The Fire Trouble display persists until the detector
causing it is restored to normal.
Viewing Fire Trouble and Fire Supervisory
Conditions
After pressing CMD 4 or the Silence button, Fire
Trouble continues to automatically scroll through the
display. To view the faulted fire points, press any
numeric key, then press Next to scroll these displays
manually. Events scroll from oldest to newest.
The display shows the instructions for clearing the
message. Enter a valid passcode and press the Clear
button.
12
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
D1265 | Owner's Manual | Part I: Security System Basics
Non-Fire Trouble and Supervisory Events
Entry Delay Tone and Display
When a trouble event occurs, your keypad might be
programmed to emit three warble tones, then a pause
(repeatedly).
When you enter an armed system through a point
programmed for entry delay, the keypad emits a
repeating warble tone and displays a warning that the
area is in entry delay. This display alternates with one
notifying you that a passcode entry is needed to turn
off your security system.
If the system was armed, the keypad display shows the
number of non-fire trouble events or non-fire
supervisory events and then custom text for each
activated point.
Silencing Non-Fire Trouble and Supervisory Events
Pressing CMD 4 or the Silence button silences and
clears Trouble and/or non-fire Supervisory conditions.
In addition to this, entering a personal passcode with
the proper authority level silences a trouble and
disarms the control panel if it was armed. If you wish
to review these cleared troubles, press CMD 40.
Viewing Non-Fire Trouble Events
After pressing CMD 4 or the Silence button, press any
numeric button to view the faulted points. Press Next
to scroll these displays manually if you wish. Events
scroll from oldest to newest.
Special System Trouble Display
These displays appear on all keypads in the system.
Refer to Standard Displays on page 86 for a description
of each system trouble display. Pressing CMD 4 or the
Silence button silences a system trouble tone, but the
System Trouble display will not clear until the faulted
condition is corrected.
A system trouble display begins by sounding a trouble
tone and then 3 sec later the specific System Trouble
Display is shown, such as Service AC Fail.
If you fail to turn off the security system before the
entry delay time expires, it will sound the burglary
tone and might also send an alarm report to your
security company.
If enabled by your security company, there
is a short period of time after the start of
the alarm that a passcode entry aborts the
transmission of the alarm report. Alarm
Aborted shows if this occurs.
Exit Delay Tone and Display
After you arm your system, the keypad emits a
repeating beep tone, shows Exit Now! And counts
down the exit delay time.
During the last 10 sec of the Exit Delay time, the
keypad will emit a more urgent tone.
Button Press Checking Tones
Valid Entry
Some systems might be programmed to
not initiate a trouble tone during these
conditions.
If you press an appropriate button for the function or
entry you desire, the keypad emits a muted beep tone,
indicating it accepted your button stroke.
Events Cleared from the Keypad Are Not Lost
Invalid Entry
If you clear the alarms and troubles from the display,
you can still view all the events that occurred since the
last time the system was armed by using CMD 40
(View Alarm Memory).
A flat buzz tone sounds when you perform a function
that is not allowed or when the keypad has no
information to display.
Silencing an Alarm
The audible alarm sounds for a specific period of time
before it automatically shuts off. If an alarm occurs and
you want to silence the siren before the time expires,
simply enter your personal passcode and press
ENTER.
To Silence an alarm:
Enter your passcode and press ENTER.
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
13
D1265 | Owner's Manual | Part I: Security System Basics
How Your System Reports Alarms
Your security system might be programmed to
automatically seize your telephones when sending
reports to your security company. Once the report is
completed, your security system restores the telephone
line to normal operation (check with your security
company). Other methods of communicating alarm
conditions are also available. Please consult your
security company for services available in your area.
Your system makes repeated attempts to send reports
to your security company.
In the event your security system fails to communicate,
the keypad sounds a Trouble Tone and shows Comm
Fail Route Grp1 (where the Route Group can be 1, 2,
3, or 4):
Notify your security company of the communications
failure.
If your system uses telephone lines as its
means of communication and telephone
service is interrupted, your security
system cannot send reports to your
security company unless it has an
alternate means of transmitting them.
14
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
D1265 | Owner's Manual | Part II: System Commands
Part II: System Commands
Some of these functions might not be
available in your system. Please consult
your security company to determine which
commands have been made available to
you.
Table 2: Keypad Commands
COMMAND
Function
Master Arm
Master Arm Instant
+
Perimeter Instant
If you attempt to enter a function that is not available
or if the function is available in the system but your
passcode is not authorized to perform the function,
then **No Authority** shows on the keypad.
Perimeter Delay
Silence Trouble Sounder and Clear
Trouble Display
View Memory
+
Walk Test
+
Reset Sensors
+
Watch Mode
Press the CMD button and then the one or two digits
shown in Table 2 to perform the function. When you
use a command to perform a function, the displays in
the function list below do not appear at your keypad.
Special Alert
Perimeter Partial
Special Alert
Some commands listed in Table 2 might
not be available. Contact your security
company for more information.
Bypass a Point
Unbypass a Point
+
Some commands listed below might not
be available. Contact your security
company for more information.
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
15
D1265 | Owner's Manual | Part II: System Commands
Passcode Protected Commands and
Functions
Commands and/or Functions within your system
might be programmed to require a valid passcode
prior to gaining access to that function. This ensures
that only authorized people have access to specific
functions.
1. The display might prompt you to enter your
passcode.
Turning the System Off (Disarming)
Entering your personal passcode turns off your security
system. When the system is turned on, you must enter
through a designated entry door to prevent an instant
alarm condition. Opening the door starts entry delay
time and the keypad emits a pulsing “beep” tone to
remind you to turn the system off. Enter your passcode
before the delay time expires and the system turns off.
If you enter through the wrong door or fail to disarm
before the entry delay time expires, you cause an
alarm.
If this happens, silence the alarm (by entering your
personal passcode and pressing ENTER) and call your
security company to let them know that it is not an
emergency situation.
If enabled by your security company,
there is a short period of time after the
start of the alarm that a passcode entry
aborts the transmission of the alarm
report. Alarm Aborted shows if this
occurs.
2. The passcode is shown as asterisks (*) when
entered and advance from the right side of the
display to the left until all passcode digits (from
a minimum of 3 to a maximum of six) are
entered.
To Turn Your Security System Off (Disarm):
3. Press ENTER.
1.
Enter your passcode and press ENTER.
2.
You must press the ENTER button within 5 sec
of entering your passcode, or the passcode entry
is invalid.
3.
The display returns to idle disarmed text.
Turning the System On (Arming)
Your security system can be turned on (armed) in
many different ways, depending on the arming
command used. Arming Commands are those
commands used to turn the system on. The most basic
arming command is to arm the entire system.
There are several other arming commands to turn the
system on. These are described later in this manual.
To Turn Your Security System On (Arm)
1.
Enter your passcode and press ENTER.
2.
After you arm your system, the keypad emits a
repeating beep tone, shows Exit now! #
seconds remaining and counts down the exit
delay time.
16
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
D1265 | Owner's Manual | Part II: System Commands
Turning On the System (Arming) With a
Duress Passcode
Turning On the System (Arming) With
Doors or Windows Open
Your passcode might have a special duress feature that
can be your personal passcode with its last digit
increased by one or two digits. Alternately, some
systems might have a specific passcode designated as
the Duress disarm passcode. Consult your security
company for your security system’s configured duress
option.
If a protected door or window is open, you might have
the option of “force arming” with that point faulted.
Faulted points (opened doors or windows) that are
force armed are not included in the system. The
remaining points arm normally.
For example, if your passcode is 1234, your duress
passcode might be 1235 or 1236.
If an intruder demands that you arm or disarm the
security system, you can use your duress passcode. The
duress passcode arms or disarms the system and sends
a duress report to your security company. There is no
alarm tone or visual indication at the premises that the
report is sent. Check with your security company
before attempting to use this feature.
Force armed points either return to normal operation
after you turn your system off or return to normal
when the door or window is closed. Your system might
not offer force arming or it might be restricted to
specific points. Contact your security company for
more information.
Use your passcode or an arming function to start the
arming process.
1.
Ensure the display shows Check Area #.
2.
One of the messages below might display in
place of Check Area #.
This display indicates the system is
programmed not to arm with particular points
faulted (doors or windows open).
This display indicates that the system’s number
of allowable bypassed points has been reached.
Your system’s maximum number of bypassed
and/or force armed points is set by your
security company. Check with them to learn
this number.
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
17
D1265 | Owner's Manual | Part II: System Commands
6.
This display indicates that more than the
number of allowable points are faulted.
Bypassed points are counted as faulted. Your
system’s maximum number of bypassed and/or
force armed points is set by your security
company. Check with them to learn this
number.
3.
Pressing the Next button at this screen aborts
the arm command and return to viewing the
faulted points.
The display shows Not Ready to Arm.
7.
4.
Once the last bypassed point is shown, the
display changes to show the button to either
force arm the faulted points (Force Arm) or
force arm the faulted/bypassed points
(Force/Bypass Arm).
Press the appropriate button to arm your system
with the faulted/bypassed points removed from
service.
Pressing the View Points button shows the
specifics for any points that are faulted or
bypassed.
Faulted points are shown first then bypassed
points.
5. The display changes to show the number of
faulted points in the area.
Press the Next button repeatedly to scroll
through the point text for each faulted point.
18
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
D1265 | Owner's Manual | Part II: System Commands
Master Arm (CMD + 1)
5.
Description
Use this function to turn on both the perimeter and
interior of a single area indicated on the first line (top)
of the keypad display. When you turn the system on,
the display shows how many seconds of exit delay time
you have to exit the protected area. You should leave
before exit delay time expires.
Leaving after exit delay has expired causes the entry
delay to start if the person exits through a point
designated Entry/Exit door. Exiting through any other
point could cause an immediate alarm. Moving into
the interior of the protected area causes an alarm on an
interior device. If an alarm occurs, enter your personal
passcode to disarm the system.
If your system is programmed to require a
passcode when performing a CMD 1, the
display prompts you to enter your passcode.
The passcode is shown as asterisks (*).
6.
If the passcode has valid authority for this
command, the display shows Exit Now! # (# =
exit delay time remaining) seconds remaining.
Your cleaning service, a serviceman, or others might
also use this function to turn on your system when they
leave.
Using Master Arm
Using the CMD+1 command only arms
the area currently displayed on the top
line of the keypad display. For example, if
the keypad is assigned to AREA 1
WAREHOUSE, only AREA 1
WAREHOUSE arms when CMD+1 is
pressed.
1.
After the exit delay time expires, the display
changes to idle armed text.
Ensure your keypad shows idle text.
7.
2.
Press the CMD button.
3.
The display shows *System Command*.
4.
Press the 1 button.
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
To disarm your security system, enter your
personal passcode and press ENTER.
19
D1265 | Owner's Manual | Part II: System Commands
Master Arming all Areas
If you prefer, you might use the Master Arm
command in the function list. Press the Menu button
to access the function list configured in the keypad.
1.
9.
To arm all available areas, press the Arm
button when the display reads Master Arm All.
Ensure your keypad shows idle text.
The display changes to show that all authorized
areas are arming.
2.
Press the Menu button to enter the function list,
then press the Next button repeatedly.
When you reach the Master Arm button, press
it.
3.
Press the button.
4.
The display might prompt you to enter your
passcode.
The passcode is shown as asterisks (*) when
entered.
The display shows Exit Now! # (# = exit delay
time remaining).
After the exit delay time expires, the display
changes to idle armed text.
10. To disarm your security system, enter your
personal passcode and press ENTER.
11. The display changes to show that all the areas
are disarmed.
The display returns to idle text.
5.
If more than one area is configured, the system
gives the option to arm all areas with Master
Arm All. To arm all areas, proceed to Step 9.
6.
To arm a selected area, press Next until the
desired area appears (Area name text along
with Arm Area #).
7.
Then press Arm.
8.
The next available area appears with the option
to arm it.
Every time the Next, Previous or Arm buttons
are pressed, the display scrolls to the next
unarmed area.
20
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
D1265 | Owner's Manual | Part II: System Commands
Master Arm Instant (CMD + 1 + 1)
Perimeter Instant (CMD + 2)
Use this function to turn on a single area, both
perimeter and interior without delays. When entering
CMD 11, remember that the second 1 must be pressed
within 2 sec after pressing the first 1.
Turn On the Perimeter With No Delays
The menu entry Master Arm Inst is different in that it
allows all or selected areas to be armed instantly.
CMD 11 does not comply with SIA CP-01
Standard.
Using the CMD + 1 + 1 command only
instantly arms the area where the keypad
has been assigned. For example, if the
D1265 is assigned to Area 1, only Area 1
is armed when CMD + 1 + 1 is pressed.
1.
Ensure your keypad shows idle text.
2.
Press the CMD button. The display shows
*System Command*.
Description
Use this function to turn on only the perimeter of your
building, leaving the interior of the building disarmed.
This function allows no exit or entry delay time
through the perimeter, including the designated exit
delay door.
This function is useful in residential systems when
everyone is home and ready to retire for the evening.
You can have the security of an armed perimeter, yet
move freely throughout the interior of the premises.
It is also useful in commercial systems when you are
working before or after business hours and wish to
have the perimeter armed. Remember there are no
entry or exit delays when you use this function. You
must disarm (turn off) the system to enter or exit the
premises.
Using Perimeter Instant
Interior points are not armed with this command and
might remain faulted while arming with CMD 2.
3.
Press the 1 button. Now press the 1 button
again.
The keypad display shows All On Instant.
1.
Press the CMD button.
2.
The display shows *System Command*.
3.
Press the 2 button.
If you prefer, you might use the function
list in place of Steps 1 through 3 to
initiate this function.
Press the Menu button to enter the
function list.
Press the Next button repeatedly.
When you reach the Perimeter Arm
Inst button, press it.
4.
To disarm your security system, enter your
personal passcode and press ENTER.
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
21
D1265 | Owner's Manual | Part II: System Commands
4.
The display shows Perimeter On Instant.
4.
After arming the perimeter without delays, you
cannot enter or exit the premises without
disarming the system. Opening a perimeter
door before disarming generates an alarm. If
this happens, silence the alarm by turning your
system off and call your security company to let
them know that it is not an emergency situation.
The display shows Exit Now! # seconds
remaining (# = exit delay time remaining).
After the exit delay expires, Perimeter On
Delayed is shown.
Perimeter Delay (CMD + 3)
Turn On the Perimeter With Delays
Description
In residential systems this function allows you to only
arm the perimeter and exit through a door
programmed for exit delay. The interior of the
building remains disarmed. People or pets are free to
move throughout the interior of the premises.
5.
To disarm your security system, enter your
personal passcode and press ENTER.
The display then returns to idle text.
This function is also useful in commercial systems
when you are working before or after business hours
and wish to have the perimeter armed. Other system
users can enter through doors programmed for entry
delay, which starts the entry delay sounder and
countdown.
Using Perimeter Delay
Interior points are not armed with this command
and might remain faulted while arming with
COMMAND 3.
1.
Press the CMD button.
2.
The display shows *System Command*.
3.
Press the 3 button.
If you prefer, you might use the function
list in place of Steps 1 through 3 to
initiate this function.
Press the Menu button to enter the
function list.
Press the Next button repeatedly.
When you reach the Perimetr Arm Delay
button, press it.
22
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
D1265 | Owner's Manual | Part II: System Commands
Silence Trouble Sound/Clear Trouble
Display (CMD + 4)
View Alarm Memory (CMD + 4 + 0)
Description
Your system stores events that occurred since the last
time memory was cleared. Use CMD 40 to view Alarm
Memory.
Use CMD 4 to silence the trouble sounder during
system events. This command also clears system
messages from the display. If an alarm has occurred
and was silenced, the *Alarm Silenced* display
continues to scroll to remind you that cleared events
can be seen with the View Alarm Memory function.
Refer to View Alarm Memory (CMD + 4 + 0) on page 23
for more information.
Using CMD 4
The display shows disarmed idle text.
1.
Press the CMD button. The display shows
*System Command*.
2.
Press the 4 button.
3.
The keypad sounder is silenced.
Description
Alarm Memory allows you or a service technician to
review events after they are cleared from the keypad’s
display. *Alarm Silenced* continues to scroll to
remind you that events are stored in Event Memory.
Each time you turn the system on, the Event Memory
is erased and the *Alarm Silenced* message is
cleared.
Using View Alarm Memory
1.
Ensure the display shows disarmed idle text.
2.
Press the CMD button. The display shows
*System Command*.
3.
Press the 4 button and then the 0 button.
If you prefer, you might use the function
list in place of Steps 2 and 3 to initiate
this function.
Press the Menu button to enter the
function list.
Press Next button repeatedly.
When you reach the View Alarm Memory
button, press it.
4.
Your system shows event summary lines and
point text in this order:
a.
fire alarm summary line
b. point text for each fire alarm event
c.
alarm summary line
d. point text for each alarm event
e.
fire trouble summary line
f.
point text for each fire trouble event
g.
trouble summary line
h. point text for each trouble event
5.
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
Press Next to scroll through the events.
23
D1265 | Owner's Manual | Part II: System Commands
If there are no events to view, There are
currently no events in memory shows.
If you prefer, you might use the function
list in place of Steps 2 and 3 to initiate
this function.
Press the Menu button to enter the
function list.
Press the Next button repeatedly.
When you reach the Walk Test button,
press it.
6.
You can return to idle text at any time by
pressing Exit button.
Walk Test (CMD + 4 + 4)
4.
Description
The burglary bell sounds for 2 sec. When the
display shows ### points remain to be tested
(### is the number of points) you can begin.
Use this function to test keypads, detection devices,
and sounders (both interior and exterior) to be certain
they function properly. You can review untested points
at your keypad to help pinpoint any problems.
You cannot arm your system while in the walk test
mode, and no alarm reports are sent to your security
company unless a 24-hour point is activated (such as
fire or panic). A Walk Test Start Report might be
programmed to be sent to your security company.
Upon initiation, the walk test tests the burglary bell
pattern on the bell output and ring the keypad
burglary bell for 2 sec. The AC is disabled for 4
minutes in order to test the system’s battery power. If
the battery cannot maintain the system for the 4minute period, the keypad appears to power off. If
your keypads are programmed to be supervised, the
main alarm panel piezo intermittently during this 4minute period. If this happens, contact your security
company. At the end of the 4-minute period, AC is
returned to the system and the control panel restores.
To test individual detection devices, simply activate
sensors and open protected doors and windows one-ata-time. As each detection device is faulted, the keypad
emits a brief tone and the display indicates for 60 sec
that the point has been tested. This verifies that each
detection device is working properly.
Test each point by first opening and then closing
the door or window, or activating the other
detection device types.
Check the display after testing each point. For
interior points, walking past the device once is
sufficient. If any point will not test correctly,
contact your security company for service.
5.
During the Walk Test you might want to refer to
the points that remain untested by pressing the
View untested pts button.
The display shows ### pts untested.
Using Walk Test
1.
Ensure the display shows disarmed idle text.
2.
Press the CMD button. The display shows
*System Command*.
3.
Press the 4 button and then the 4 button.
24
Press the Next Pt or Prev Pt buttons to refer to
information about specific points that have not
yet been tested.
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
D1265 | Owner's Manual | Part II: System Commands
6.
Move through this list by pressing the Next Pt
button.
Reset Sensors (CMD + 4 + 7)
Description
Detection devices, such as smoke detectors and shock
sensors, must be reset after being activated. This
function momentarily removes power from these
sensors to reset them.
Using Reset Sensors
The display changes to show the information for
that point.
1.
Ensure the display shows disarmed idle text.
2.
Press the CMD button. The display shows
*System Command*.
3.
Press the 4 button, followed by the 7 button.
Press the Exit button to return to the ### points
remain to be tested screen before continuing
with the walk test.
7.
When all points have been tested, 0 points
remain to be tested is shown.
Press the Exit button.
The display momentarily shows All points have
been tested.
The display then shows idle text.
If you prefer, you might use the function
list in place of Steps 2 and 3 to initiate
this function.
Press the Menu button to enter the
function list.
Press the Next button repeatedly.
When you reach the Reset Sensors
button, press it.
4.
The display shows for approximately 15 sec.
While the sensors reset, the keypad resets
before it returns to idle text.
If you enter this function and the detector or sensor
resets momentarily, but then returns to a faulted
condition, the conditions causing the activation might
still be present or the detector might be faulty. Check
to be certain that there is no smoke, fire, or other
danger present. If you can’t reset the detector or
sensor, contact your security company.
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
25
D1265 | Owner's Manual | Part II: System Commands
Watch Mode (CMD + 6)
Description
With your security system disarmed, you can use
watch mode to monitor some points. Each time some
points are faulted (door or window is opened) the
keypad chimes once and shows the point text for 60
sec. No alarms are generated by this mode except 24hour alarms (fire, panic, and so on).
Use this function in residential systems to monitor
entries or exits in your home. In commercial systems it
can serve as a door chime to alert you when a
customer or delivery person enters your business.
Entering Watch Mode
1. The display shows disarmed idle text.
2. Press the CMD button. The display shows
*System Command*.
3.
If you prefer, you might use the function
list in place of Steps 2 and 3 to initiate
this function.
Contact your security company to find out
which points are watch points and
whether or not your system automatically
turns the Watch Mode on whenever you
disarm.
Press the Menu button to enter the
function list.
Press Next button repeatedly.
Using Watch Mode
When you reach the Watch Mode button,
press it.
Description
With your security system disarmed, you can use
watch mode to monitor some points. Each time some
points are faulted (door or window is opened) the
keypad chimes once and shows the point text for 60
sec. No alarms are generated by this mode except 24hour alarms (fire, panic, and so on).
Press the 6 button.
4.
The display briefly shows Watch Mode is now
on.
When the keypad’s keypad lighting is on, the keypad
will not chime. The buttons light for 20 sec whenever
you press a button.
Use this function in residential systems to monitor
entries or exits in your home. In commercial systems it
can serve as a door chime to alert you when a
customer or delivery person enters your business.
Contact your security company to find out
which points are watch points and
whether or not your system automatically
turns the Watch Mode on whenever you
disarm.
26
The display returns to show idle text.
Exiting Watch Mode:
1.
Ensure the display shows disarmed idle text.
2.
Press the CMD button. The display shows
*System Command*.
3.
Press the 6 button.
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
D1265 | Owner's Manual | Part II: System Commands
If you prefer, you might use the function
list in place of Steps 2 and 3 to initiate
this function.
Press the Menu button to enter the
function list.
Press the Next button repeatedly.
When you reach the Watch Mode button,
press it.
4.
The display briefly shows Watch Mode is now
off.
Perimeter Partial (CMD + 8)
Partially Turn On the Perimeter
Description
This function is used to turn on the perimeter of your
building while selected portions of the perimeter
remain turned off. Perimeter points that are not secure
(faulted) when this function is entered are
automatically bypassed and are not included in the
system. This function will not turn on the interior of
your building. Entry/exit delays are provided with this
arming command.
Use this function in residential systems to turn on the
front of your house while the interior and the rear
perimeter doors are left turned off, giving you freedom
of movement between the house and patio.
In commercial systems, when you need access to the
large overhead doors to receive deliveries, using this
function allows you to keep the rest of the building
perimeter armed.
The display returns to show idle text.
Using Perimeter Partial
1.
Ensure the display shows disarmed idle text.
2.
Press the CMD button. The display shows
*System Command*
.
3.
Press the 6 button.
If you prefer, you might use the function
list in place of Steps 2 and 3 to initiate
this function.
Press the Menu button to enter the
function list.
Press the Next button repeatedly.
When you reach the Perimeter Arm Part
button, press it.
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
27
D1265 | Owner's Manual | Part II: System Commands
5.
The display prompts the user to exit the area
and starts counting down # seconds to arm the
system.
Special Alerts (CMD + 7 and CMD + 9)
Description
Commands 7 and 9 can be programmed to respond to
specific situations that might need immediate attention.
They might also be used to send a silent alarm to your
security company without sounding an alarm signal on
the premises. Check with your security company for
the options they offer.
Using CMD 7
# is the number of sec remaining in the
countdown.
6.
When exit delay time expires and the system
turns on, the display shows:
1.
Ensure your keypad shows idle text.
2.
Press the CMD button. The display shows
*System Command*.
3.
Press the 7 button.
If you prefer, you might use the function
list in place of Steps 2 and 3 to initiate
this function.
Press the Menu button to enter the
function list.
7.
Press the Next button repeatedly.
To disarm, enter your personal passcode and
press ENTER.
When you reach the User Command 7
button, press it.
4.
Your Command 7 special alert has been
programmed to:

notify your alarm company

ring a bell on your premises

display at your keypad
Description:
_________________________________________
_________________________________________
28
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
D1265 | Owner's Manual | Part II: System Commands
Using Command 9
1.
Ensure the display shows disarmed idle text.
2.
Press the CMD button. The display shows
*System Command*.
3.
Press the 9 button.
If you prefer, you might use the function
list in place of Steps 2 and 3 to initiate
this function.
Press the Menu button to enter the
function list.
Press the Next button repeatedly.
When you reach the User Command 9
button, press it.
4.
Your Command 9 special alert has been
programmed to:

notify your alarm company

ring a bell on your premises

display at your keypad
Description:
_________________________________________
_________________________________________
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
29
D1265 | Owner's Manual | Part III: Advanced Commands
Part III: Advanced Commands
Use this section of the manual to perform advanced system functions like add and delete user passcodes, reassign
authority levels to user passcodes and operate or change programmed scheduled events (Skeds) from the keypads.
As you make changes to the system, update the information contained in the tables in this guide to provide an
accurate account of the programmed information.
Advanced Commands
Some commands listed below might not be available. Contact your security company for more
information.
Advanced
COMMAND
Function
Advanced
COMMAND
Function
Bypass a Point
+
Change Sked
Unbypass a Point
+
Delete Passcode
+
Test Report
+
Change Relay
+
Status Report
+
Change Passcode
+
Remote Program
+
Add Passcode
+
Change Time/Date
+
Default Text
+
Door Control
+
Fire Test
Access Level Change
+
Display Rev
+
+
Change Display
Print Log
+
Move to Area
View Log
+
Extend Closing
View Point Status
Terms Used in This Section
Listed below are some of the terms you’ll see throughout this section. Each term is covered in greater detail later
in this section and in Part II: System Commands.
Account
One or more areas reporting under a particular account number.
Area
A group of detection devices connected to your security system.
Arm and Disarm
To switch your burglar detection devices “on” and “off.” When the burglar detection
device is armed and is tripped, an alarm might be set off. When the burglar
detection devices are disarmed, the security system will not detect intruders.
Detection devices programmed as 24-Hour or Fire points are always on.
Authority Levels
Levels of access authority assigned to passcodes.
Keypad
Arming station used to operate your security system.
Keypad Scope
Determines which areas a particular keypad can access.
Control Panel
The main control unit, which is locked in a steel enclosure. It sends data to and
receives inputs from the keypads.
Relays
Optional dry contact outputs that respond to system events.
Skeds
Functions programmed by your security company that occur at predetermined
times.
30
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
D1265 | Owner's Manual | Part III: Advanced Commands
User Passcodes
A three to six digit number entered at a keypad to access the system.
Bypass a Point (CMD + 0)
5.
The display changes to show Enter point
number or press next key.
6.
If a digit is pressed, the display shows Enter
point number: #. As soon as a digit button is
pressed, the display changes to Entering point
number (# is the point number entered).
Description
This command allows you to bypass points that you do
not want included in the system. Points that are not
included in the system do not detect intruders and
cannot send any reports. You can bypass points when
an area is disarmed. Bypassing a point reduces the
level of security and should be used with discretion.
Points remain bypassed until you unbypass them, or
some points might return when the area is disarmed
(refer to Unbypass a Point (CMD + 0 + 0) on page 33).
You could use CMD 0 to leave a window open over
night without initiating an alarm. Also refer to Turning
On the System (Arming) With Doors or Windows Open on
page 17.
Using Bypass a Point
1.
Ensure your keypad shows idle text.
2.
Press the CMD button. The display shows
*System Command*.
If you know the point number you wish to
bypass, enter the number and press the ENTER
button.
If you don’t know the number of the point you
wish to bypass, you can view the list of devices
that can be bypassed by pressing the Next
button.
3.
Press the 0 button.
If you prefer, you might use the function
list in place of Steps 2 and 3 to initiate
this function.
Press the Menu button to enter the
function list.
Press the Next button repeatedly.
When you reach the Bypass a Point
button, press it.
4.
Continuously pressing Next scrolls through the
available points that can be bypassed.
When the point text of the point you wish to
bypass appears, press the Bypass button.
P3 ENTRY DELAY is not bypassed indicates
the point is not bypassed and the option is
given to bypass it.
You might be prompted for your passcode. It
appears on the display as asterisks (*).
One of the following messages shows (P3
ENTRY DELAY is used here as an example):
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
31
D1265 | Owner's Manual | Part III: Advanced Commands
P3 ENTRY DELAY is now bypassed indicates
the point was successfully bypassed.
P3 ENTRY DELAY is already bypassed
indicates that the point has already been
bypassed.
7.
If the bypassed point is a Fire Point, the
message Fire Point Bypassed begins alternating
in the display with A1 Area Is Off.
8.
If the bypassed point is a 24-hour point, the
message 24hr Point Bypassed begins
alternating in the display with A1 Area Is Off.
P3 DELAY cannot be bypassed indicates the
system is programmed not to allow that point to
be bypassed.
Invalid point Please try again indicates that
the entered point doesn’t exist and the display
returns to allow another point to be entered.
No additional points indicates that there are
no more points that can be bypassed.
32
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
D1265 | Owner's Manual | Part III: Advanced Commands
Unbypass A Point (CMD + 0 + 0)
Description
Unbypassing a point is a way to return a bypassed
point to the security system so that it can once again
respond to trouble and alarm conditions.
6.
If digits are pressed, the display shows Enter
point number: #. As soon as a digit button is
pressed, the display changes to Entering point
number (# is the point number that was
entered).
Using Unbypass a Point
1.
Ensure the display shows disarmed idle text.
2.
Press the CMD button. The display shows
*System Command*.
If you know the point number you wish to
unbypass, enter the number and press the
ENTER button.
3.
Press the 0 button twice.
If you prefer, you might use the function
list in place of Steps 2 and 3 to initiate
this function.
Press the Menu button to enter the
function list.
If you don’t know the number of the point you
wish to unbypass, you can view the list of
devices that can be unbypassed by pressing the
Next button.
Continuously pressing Next scrolls through the
available points that are currently bypassed.
When the point text of the point you wish to
unbypass appears, press the Unbypass button.
Press the Next button repeatedly.
When you reach the Unbypass a Point
button, press it.
4.
5.
You might be prompted for your passcode. It
appears on the display as asterisks (*).
The display changes to show Enter point
number or press next key.
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
One of the following messages shows (P3
ENTRY DELAY is used here as an example):
P3 ENTRY DELAY is now bypassed indicates
the point was successfully bypassed.
Invalid point Please try again indicates that
the entered point doesn’t exist and the display
returns to allow another point to be entered.
33
D1265 | Owner's Manual | Part III: Advanced Commands
No additional points indicates that there are
no more points that can be bypassed.
Send Report (CMD + 4+1 or 4+2)
Description
This function tests the communication link between
your security system and your security company. It is
an important part of maintaining a high level of
security for your property.
If an unbypassed point is entered, an error tone
will sound and a warning will be displayed.
Two types of test reports can be sent. The first type of
report is a simple test report (Command 41). The
second type of report is a status report (Command 42).
This status report indicates the current condition of
your system.
Using Send Report
1.
Always call your security company before
sending a test report.
2.
Ensure the display shows disarmed idle text.
3.
Press the CMD button. The display shows
*System Command*.
4.
Press the 4 button then the 1 button to send a
test report.
The display returns to idle text.
7.
If you are attempting to unbypass a 24-Hour or
Fire Point that is still faulted, the keypad shows
Cannot unbypass 24hr faulted points.
Press the 4 button then the 2 button to send a
status report.
If you prefer, you might use the function
list in place of Steps 3 and 4 to initiate
this function.
Press the Menu button to enter the
function list.
Press the Next button repeatedly.
When you reach the Send Report button,
press it.
Another menu appears allowing for the
selection of sending a test report (Test
Rpt) or a status report (Status Rpt).
Press either button.
5.
34
The keypad shows Sending report… Please
wait… until the report is transmitted to the
security company.
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
D1265 | Owner's Manual | Part III: Advanced Commands
6.
When the transmission is complete the keypad
shows Report sent for 5 sec.
Remote Program (CMD + 4 + 3)
Description
This function allows the user to initiate Remote
Programming Software (RPS) sessions. When the
phone is ringing at the control panel, the user initiates
this function to have the control panel seize the line.
The display returns to idle text.
Your security company can remotely program your
security system using the telephone line to which your
control panel is connected. Typical remote
programming functions include: changing personal
passcodes, changing entry/exit delays, resetting the
system clock/calendar, and adding/deleting system
arming commands.
If the test (or status) report does not successfully
transmit to the central station, the keypad might
sound a trouble tone and display Comm Fail
Route Grp# (# = 1-4) after numerous
unsuccessful attempts.
Your security company might ask you to follow the
steps below to begin a remote programming session.
The time it takes to program the control panel is
dependent on the number of changes made to the
program.
If the Exit button is pressed before 5 sec
have elapsed, idle text is shown.
7.
You’ll notice that two sets of procedures are presented.
The one you use depends upon whether your system
has a pre-programmed telephone number in its
memory.

My system does not have the RPS phone or
the RPS network configured.
For systems without a phone number
1.
Ensure the display shows disarmed idle text.
2.
Call this phone number:
This number is designated for the RPS.
You must make the call using the telephone
located at:
___________________________
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
3.
Identify yourself and your premises (account
number, name, address, etc.) and advise the
operator of the services you wish to have
performed. When the operator instructs you,
proceed to Steps 4 through 6.
4.
Press the CMD button. The display shows
*System Command*.
5.
Press the 4 button then the 3 button.
6.
Advance the menu (if necessary) and select the
Allow Answer option.
35
D1265 | Owner's Manual | Part III: Advanced Commands
7.
8.
9.
If you prefer, you might use the function
list in place of Steps 2 and 3 to initiate
this function.
If you prefer, you might use the function
list in place of Steps 2 and 3 to initiate
this function.
Press the Menu button to enter the
function list.
Press the Menu button to enter the
function list.
Press the Next button repeatedly.
Press the Next button repeatedly.
When you reach the Remote Program
button, press it.
When you reach the Remote Program
button, press it.
Press ENTER.
Press ENTER.
The display shows RPS connecting…
The security system now allows RPS to connect
over the phone line or over the network to the
control panel.
At the conclusion of the programming session
your system sends a report to the security
company and then returns your telephone to
normal service and your display to idle text.
For systems with a phone number configured

My system uses a phone number for Remote
Programming
1.
Ensure your keypad shows idle disarmed text.
2.
Press the CMD button. The display shows
*System Command*.
3.
36
4.
Select RPS via Phone.
5.
The display shows RPS connecting…
6.
The security system now calls the telephone
number specified for the remote programming
session.
7.
At the conclusion of the programming session
your system sends a report to the security
company and then returns your telephone to
normal service and your display to idle text.
For systems with a network connection

My system uses an IP Address and network
connection for Unattended Remote
Programming
1.
Ensure your keypad shows idle disarmed text.
2.
Press the CMD button. The display shows
*System Command*.
3.
Press the 4 button then the 3 button.
Press the 4 button then the 3 button.
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
D1265 | Owner's Manual | Part III: Advanced Commands
If you prefer, you might use the function
list in place of Steps 2 and 3 to initiate
this function.
Press the Menu button to enter the
function list.
Press the Next button repeatedly.
When you reach the Remote Program
button, press it.
Press ENTER.
4.
Select RPS via Network.
5.
Do one of the following:

My system uses the default port number
for network connection. Press Use Port
### and then skip to Step 7.

My system uses an alternate port number
for network connection: _____________.
Change Time/Date (CMD + 4 + 5)
The time and date in your system must be correct for
scheduled events to occur at the correct times. Check
the time at least once a month to ensure accuracy. Use
this function to set both the time and date. The system
uses a 12-hour, AM/PM format. There is the option to
continuously display the time and date in place of area
status. The Time and Date is shown continuously until
a new command is entered or the current area’s status
has changed. Refer to Change Display (CMD + 4 + 9) on
page 42, Time/Date Display for more information.
1.
Ensure your keypad shows idle disarmed text.
2.
Press the CMD button. The display shows
*System Command*.
3.
Press the 4 and then the 5 button.
If you prefer, you might use the function
list in place of Steps 2 and 3 to initiate
this function.
6.
Select the Enter Port Number option and enter
the port number specified.
7.
The security system now connects to the IP
Address specified for network connection
during the remote programming session.
8.
At the conclusion of the programming session
your system sends a report to the security
company and then returns the display to idle
text.
Press the Menu button to enter the
function list.
Press the Next button repeatedly.
When you reach the Change Time/Date
button, press it.
4.
The display shows Enter new time.
To just change the date, press the Set Date
button. Refer to Step 6.
If you input the wrong time, press the Exit
button to clear the time.
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
37
D1265 | Owner's Manual | Part III: Advanced Commands
Enter the new time using a 12-hour (HH:MM)
format.
8.
Example: If the desired time is 12:34, press 1
+2+3+4
The Time/Date Display button is used to show
how the time and date entered appears.
9.
Press the ENTER button.
The new time and/or date is shown for 20 sec
before the display returns to idle text.
The Set Date button disappears when the
first digit is entered.
Press the Exit button to return to idle text.
5.
Press the ENTER button.
6.
The display changes to show AM or PM
buttons.
Press the AM button to select AM.
Press the PM button to select PM.
7.
The display shows Enter new date.
Refer to Step 9 for use of the Time/Date
Display button.
If you input the wrong date, press the Exit button to
clear the date.
Enter the new date using a MM/DD/YY
format.
Example: If the desired time is July 28, 2010,
press 0 + 7 + 2 + 8 + 1 + 0.
38
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
D1265 | Owner's Manual | Part III: Advanced Commands
Door Control (CMD + 4 + 6)
4.
Description
There are three functions with the door control
function:
 Cycle Door – momentarily unlocks a door to
allow a person into an area
 Unlock Door – unlocks a door to allow free access
 Secure Door – locks a door and prohibits access
regardless of a user’s authority level
Using Door Control
1.
Ensure your keypad shows idle disarmed text.
2.
Press the CMD button. The display shows
*System Command*.
3.
Press the 4 button and the 6 button.
If you prefer, you might use the function
list in place of Steps 2 and 3 to initiate
this function.
The display changes and shows all authorized
choices of Cycle Door, Unlock Door, and
Secure Door.
Press the desired button.
Cycle Door
1.
If you wish to momentarily unlock an access
door to allow a person into an area, press the
Cycle Door button.
2.
The display reads *Cycle Door*1 2 3 4 5 6 7 8
if all door are at a normal state and are
available.
If a door is not at a normal state, the number of the
door would be replaced with a symbol indicated in
Table 3.
If a door is not at a normal state, the number of the
door would be replaced with a symbol indicated in
Table 3.
Table 3: Door Status
Press the Menu button to enter the
function list.
Press the Next button repeatedly.
When you reach the Door Control Menu
button, press it.
Symbol
C
U
X
F
1-8
3.
Meaning
Door is not active, in scope, or user will not
have access level authority.
Door is on timed door sequence.
Strike and shunt are latched active (held
open).
Strike and shunt are deactivated (secured).
There is a problem with the door. Call your
security company.
Door is locked and ready for a command.
Enter the number of the door you wish to cycle
then press the ENTER button. This door is
cycled and the display changes to reflect the
new status of the doors.
For example, if you wanted to cycle Door 3,
press 3 then press the ENTER button.
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
39
D1265 | Owner's Manual | Part III: Advanced Commands
4.
The display changes to show that all the doors
are at a normal state except for Door 3, which is
cycled.
2.
The display reads *Secure Door*1 2 3 4 5 6 7 8
if all door are at a normal state and are
available.
The display will return to the door number
when the cycle command is complete.
5.
Enter another door number to cycle or press
the Exit button to leave this function.
Unlock Door
1.
If you wish to unlock an access door to allow
free access, press the Unlock Door button.
2.
The display reads *Unlock Door*1 2 3 4 5 6 7
8 if all door are at a normal state and are
available.
If a door is not at a normal state, the number of the
door would be replaced with a symbol indicated in
Table 3 on page 39.
3.
For example, if you wanted to secure Door 3,
press 3 then press the ENTER button.
If a door is not at a normal state, the number of
the door would be replaced with a symbol
indicated in Table 3.
3.
Enter the number of the door you wish to
unlock then press the ENTER button. This door
is unlocked and the display changes to reflect
the new status of the doors.
The display changes to show that all the doors are
at a normal state except for Door 3, which is
secured.
4.
Enter the door number again to return it to the
normal mode. The display shows the door number
again.
5.
Press the Exit button to leave this function.
For example, if you wanted to unlock Door 3,
press 3 then press the ENTER button.
The display changes to show that all the doors
are at a normal state except for Door 3, which is
unlocked.
4.
Enter the door number again to return it to the
normal mode. The display shows the door
number again.
5.
Press the Exit button to leave this function.
Enter the number of the door you wish to secure
then press the ENTER button. This door is
secured and the display changes to reflect the new
status of the doors.
Secure Door
1.
40
If you wish to unlock an access door to allow
free access, press the Unlock Door button.
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
D1265 | Owner's Manual | Part III: Advanced Commands
Access Level
This function is used to manually enable/disable access
authority levels assigned to users. It can also be used to
temporarily disable a user’s access level instead of
deleting and then re-adding the user.

I have this feature.

I do not have this feature.
1.
Ensure your keypad shows idle disarmed text.
2.
Press the Menu button to enter the function list.
3.
Press Next button repeatedly until you reach
the Change Level button.
9.
After selecting whether to disable or enable the
level, the display prompts you again to enter an
Authority Level to modify.
10. Press the Exit button when you are finished.
Press the button.
4.
The display prompts you to enter your
passcode. Enter your passcode and press the
ENTER button.
5.
A prompt appears asking for entry of the
Authority Level to be modified.
6.
Enter the level number (1 – 14) and press the
ENTER button.
7.
If the level entered is currently enabled, the
keypad asks if you want to disable this level.
8.
If the level entered is currently disabled, the
keypad asks if you want to enable this level.
(Level 1 is used here as an example.)
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
41
D1265 | Owner's Manual | Part III: Advanced Commands
Change Display (CMD + 4 + 9)
Extend Closing (CMD + 5 + 1)
Show Continuous Time/Date
Your system might be programmed to expect you to
arm within a scheduled closing window, which is a
duration of time that is programmed by your alarm
company. Your system might also be programmed to
automatically arm at the end of the window.
Use this function to replace the disarmed idle text with
a continuous time and date display and to prevent a
passersby from knowing the status of your system.
Any time your keypad has an event to display, the
time and date display is automatically removed. To
return the time and date display, you must perform
this function again.
1.
Ensure your keypad shows idle disarmed text.
2.
Press the CMD button. The display shows
*System Command*.
CMD 51 lets you extend the scheduled closing window
time either prior to the closing window time or during
the closing window time. Use this function when you
expect to stay past the scheduled end of the closing
window. Your alarm company sets the length of time
prior to the start of the closing window in which you
are allowed to extend the closing window.
Close window is not currently active shows during
the time when the keypad won’t allow the window to
be extended.
3.
Press the 4 and then the 9 button.
If you prefer, you might use the function
list in place of Steps 2 and 3 to initiate
this function.
Press the Menu button to enter the
function list.
Press the Next button repeatedly.
When you reach the Change Display
button, press it.
At the beginning of the closing window, the keypad
beeps and shows Please Close Now to remind you to
arm your system. It remains on the display until you
arm, the close window ends, or you extend closing.
The closing window can only be extended
once the window has started.
Alarm or trouble messages replace this message in the
event of an alarm or trouble condition.
4.
Select Time/Date Display. The display will return
to idle and the area status will be replaced with the
Time and Date.
The Bright Display and Dim Display
options are not supported on the D1265
keypad.
Pressing the Silence button silences the beep and clear
the message for 10 minutes.
If the alarm or trouble condition clears before the end
of the close window Please Close Now message
returns to the keypad display.
42
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
D1265 | Owner's Manual | Part III: Advanced Commands
If you have not armed or extended closing, the Please
Close Now message and beep reappears after 10
minutes. Your alarm company sets the length of time
for the closing window. To extend the window, enter
the new time at which you would like the reminder
tone to begin. This time is the new beginning of the
closing window. The time length of the closing window
is programmed by your security company and remains
fixed.
When you hear the warning you can:
 Press the Silence button silences the beep and
clear the message for 10 minutes
 Leave before the end of the closing window
 Stay past the scheduled end of the closing window,
by using CMD 51 to extend the closing window.
Extending the closing window will not
effect the amount of time available to close.
If you prefer, you might use the function
list in place of Steps 2 and 3 to initiate
this function.
Press the Menu button to enter the
function list.
Press the Next button repeatedly.
When you reach the Extend Closing
button, press it.
4.
Press the Change button to change the start time.
Press the Accept button to accept the start time
and return to idle text.
5.
For example, if your closing window starts
at 4:00 p.m. and stops at 4:30 p.m. and
you extend closing to 5:00 p.m., the
closing window is now between 5:00 and
5:30 p.m.
1.
Ensure your keypad shows idle disarmed text.
2.
Press the CMD button. The display shows
*System Command*.
3.
Press the 5 button and then the 1 button.
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
The display changes to show the current start time.
Enter the new time using a 12-hour (HH:MM)
format.
Example: If the desired time is 12:34, press [1]
[2] [3] [4]
Press the AM button to select AM.
Press the PM button to select PM.
6.
The display changes to show the new start time
briefly before returning to idle text.
7.
Press the Accept button to accept the Close Start
time.
43
D1265 | Owner's Manual | Part III: Advanced Commands
When an X appears in the Sked display, it is an
indication that “Except on Holidays” is enabled.
Chg Skeds (CMD + 5 + 2)
Description
A Sked is a function programmed to be performed
automatically at a scheduled time by your security
system. You can change the scheduled time for some
functions, disable the Sked and thus prevent it from
automatically happening or restart a previously
disabled Sked. Contact your security representative to
determine what Skeds might be programmed for your
system.
Specific holidays are programmed by your
security company.
When an * appears in the Sked display, it is an
indication that the Sked has or happens today.
5.
If the Sked is currently enabled, the sked is
shown with Disable this sked on the second
line. Press the adjacent button.
6.
The display changes to show that the sked is
disabled.
To change a Sked’s time, enable a Sked, or disable a
Sked, follow the procedure below to first select the
Sked from a list of Skeds programmed for your system.
If the Sked is currently disabled, the display
reads Skd 1 is disabled.
Using Chg SKEDS
1.
Ensure your keypad shows idle disarmed text.
2.
Press the CMD button. The display shows
*System Command*.
Press the Enable this sked button.
7.


3.
4.
The display shows two buttons:
Only on holiday
Pressing this button enables the sked only
on holidays and change the first line of the
display to Skd 1 X 08:00AM without the X.
Except on holiday
Pressing this button disables the sked on
holidays and change the first line of the
display to Skd 1 08:00am with the X.
Consult your security company and
determine which holidays have been
programmed in your system.
Press the 5 button and then the 2 button.
If you prefer, you might use the function
list in place of Steps 2 and 3 to initiate
this function.
The display changes to allow a new time to be
entered.
Press the Menu button to enter the
function list.
Enter the new time using a 12-hour (HH:MM)
format.
Press the Next button repeatedly.
For example, if the desired time is 8:00, press 8
+ 0 + 0.
When you reach the Change Skeds
button, press it.
Press the ENTER button.
8.
The number of the first Sked programmed into
your system is shown, plus either its time or an
indication that it is disabled.
Press the Next button to scroll through the list
of Sked numbers to find the one you wish to
change.
If the time is a valid time, the keypad display
changes to show the new time with a selection
of AM or PM.
Press the AM button to select AM.
Press the PM button to select PM.
9.
The display shows the Sked with the new time.
Press the Exit button to return to idle text.
Your alarm system might be programmed with
up to 40 Skeds. If the Sked number being
shown is not programmed, the keypad shows
Skd11 – No program.
44
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
D1265 | Owner's Manual | Part III: Advanced Commands
Table 4: Sked Table
SKED #
SKED 1
SKED 2
SKED 3
SKED 4
SKED 5
SKED 6
SKED 7
SKED 8
SKED 9
SKED 10
SKED 11
SKED 12
SKED 13
SKED 14
SKED 15
SKED 16
SKED 17
SKED 18
SKED 19
SKED 20
SKED 21
SKED 22
SKED 23
SKED 24
SKED 25
SKED 26
SKED 27
SKED 28
SKED 29
SKED 30
SKED 31
SKED 32
SKED 33
SKED 34
SKED 35
SKED 36
SKED 37
SKED 38
SKED 39
SKED 40
Except on
Holiday
Yes / No
Yes / No
Yes / No
Yes / No
Yes / No
Yes / No
Yes / No
Yes / No
Yes / No
Yes / No
Yes / No
Yes / No
Yes / No
Yes / No
Yes / No
Yes / No
Yes / No
Yes / No
Yes / No
Yes / No
Yes / No
Yes / No
Yes / No
Yes / No
Yes / No
Yes / No
Yes / No
Yes / No
Yes / No
Yes / No
Yes / No
Yes / No
Yes / No
Yes / No
Yes / No
Yes / No
Yes / No
Yes / No
Yes / No
Yes / No
Time
Date
Day of Week
Function
SMTWTFS
SMTWTFS
SMTWTFS
SMTWTFS
SMTWTFS
SMTWTFS
SMTWTFS
SMTWTFS
SMTWTFS
SMTWTFS
SMTWTFS
SMTWTFS
SMTWTFS
SMTWTFS
SMTWTFS
SMTWTFS
SMTWTFS
SMTWTFS
SMTWTFS
SMTWTFS
SMTWTFS
SMTWTFS
SMTWTFS
SMTWTFS
SMTWTFS
SMTWTFS
SMTWTFS
SMTWTFS
SMTWTFS
SMTWTFS
SMTWTFS
SMTWTFS
SMTWTFS
SMTWTFS
SMTWTFS
SMTWTFS
SMTWTFS
SMTWTFS
SMTWTFS
SMTWTFS
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
45
D1265 | Owner's Manual | Part III: Advanced Commands
If the user number entered is not a valid user in
the system, the display shows This user is
currently not in use.
Delete User (CMD + 5 + 3)
This function allows a user to be deleted.
This function deletes the passcode,
Master access card/token and all subuser access cards/tokens associated with
the user number.
1.
Ensure your keypad shows idle disarmed text.
2.
Press the CMD button. The display shows
*System Command*.
6.
Press the Yes button to delete the user.
The display briefly shows that the user has been
deleted before returning to idle text (3 is used as
an example).
3.
Press the 5 button and then the 3 button.
If you prefer, you might use the function
list in place of Steps 2 and 3 to initiate
this function.
Press the Menu button to enter the
function list.
The user text is not deleted when deleting
a user. To modify a user’s text, refer to
Add/Change User (CMD + 5 + 6) on
page 48.
Press the Next button repeatedly.
When you reach the Delete User button,
press it.
4.
The display changes to show Enter user # to be
deleted.
Enter the user number, not the passcode. (123 is
as an example.)
Press the ENTER button.
5.
If the user number entered is a valid user in the
system, the display shows Delete User 3? Are
you sure?
(3 is used as an example.)
46
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
D1265 | Owner's Manual | Part III: Advanced Commands
Change Relay (CMD + 5 + 4)
Your security company might program relays for
automatic control and/or control from your keypad of
devices such as premises lighting or entry gates.
Contact them for further information regarding the use
of relays in your security system.
1.
Ensure your keypad shows idle disarmed text.
2.
Press the CMD button. The display shows
*System Command*.
5.
If the relay is valid and turned off, the display
changes to Change Relay* Relay 123 is
currently off.
(123 is used as an example.)
Press the Turn on button to turn on the relay.
6.
If the relay is valid and turned on, the display
changes to Change Relay* Relay 123 is
currently on.
(123 is used as an example.)
Press the Turn off button to turn off the relay.
7.
The display returns to the *Change Relay*
Enter relay number.
Press the Exit button to return to idle text.
The on-board relays use the following
numbers:
3.
Press the 5 button and then the 4 button.
If you prefer, you might use the function
list in place of Steps 2 and 3 to initiate
this function.
Press the Menu button to enter the
function list.
Press the Next button repeatedly.
When you reach the CHG RELAYS
button, press it.
4.
The keypad display changes *Change Relay*
Enter relay number.
Valid entries are 1 to 128, depending how the
system is configured.
Enter the relay number then press the ENTER
button.
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
Relay A
250
Relay B
251
Relay C
252.
Change Passcode (CMD + 5 + 5)
Description
Use this function to change your personal passcode
without assistance from the security company.
Before you begin:
 Choose a new passcode three to six digits long. If
you choose a passcode with the same digit in
consecutive order (for example “33” in 334697),
take care when entering it.
 To avoid conflicting with other passcodes and
duress codes, your system will not let you change
passcodes to an existing passcode or to within plus
or minus 2 of an existing passcode. For example, if
1234 were an existing code, your system would not
let you change your code to 1232, 1233, 1234,
1235, or 1236.
Using Change Passcode
1.
Ensure your keypad shows idle disarmed text.
2.
Press the CMD button. The display shows
*System Command*.
3.
Press the 5 button and then the 5 button.
47
D1265 | Owner's Manual | Part III: Advanced Commands
If you prefer, you might use the function
list in place of Steps 2 and 3 to initiate
this function.
7.
If the new passcode is valid, the display changes
to Enter new passcode again:
Enter the new passcode again.
Press the Menu button to enter the
function list.
As soon as a number is pressed, Entering:
appears on the third line next to the asterisks.
Press the Next button repeatedly.
When you reach the Change Passcode
button, press it.
4.
You are prompted for your passcode.
The passcode is shown as asterisks (*) when
entered and advance from the right side of the
display to the left until all six passcode digits are
entered.
As soon as a number is pressed, Entering:
appears on the third line next to the asterisks.
The passcode is shown as asterisks (*) when
entered and advance from the right side of the
display to the left until all passcode digits are
entered.
5.
8.
The display changes to Enter new passcode:
If the passcode does not match, the keypad
emits an error tone and displays Passcode not
changed.
Enter the new passcode.
As soon as a number is pressed, Entering:
appears on the third line next to the asterisks.
If the passcode matches the previously entered
passcode, the display changes to Passcode
changed.
9.
The display automatically returns to idle text
after 3 sec.
Add/Change User (CMD + 5 + 6)
The passcode is shown as asterisks (*) when
entered and advance from the right side of the
display to the left until all passcode digits are
entered.
6.
Press the ENTER button.
If a duplicate passcode is entered, the keypad
momentarily reads Passcode is already in use.
Please try again.
48
Use this function to add or change a user to your
system without assistance from your security company.
You need to know which user numbers are available,
the authority level you want to assign to the new
passcode and the areas in which it is valid before you
add it.
The user numbers identify users in reports transmitted
from your system. Additionally, you are able to change
the following:
 the authority level (which determines what system
functions the passcode can access)
 the area number (which identifies which parts of
your security system the user has access to)
 the name of the user
 door access card or token they use for access
control
 the door access card or token associated with the
Master or Sub-User.
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
D1265 | Owner's Manual | Part III: Advanced Commands
Contact your security company if you don’t know what
user numbers, authority levels, or areas are available.
Refer to the Appendix on page 67 for further
information on adding passcodes.
Before you begin, keep these points in mind:
 Do not try to add new users without knowing the
available user numbers. An already defined user
number is overwritten when the new user is
defined. These are two or three digit numbers, not
to be confused with passcodes that identify users at
your security company.
 When choosing passcodes, choose a new passcode
three to six digits long. If you choose a passcode
with the same digit in consecutive order (for
example “33” in 334697), take care when entering
it.
 To avoid conflicting with other passcodes and
duress codes, your system will not let you change
passcodes that are the same within plus or minus 2
of an existing passcode. For example, if 1234 were
an existing code, your system would not let you
add or change your code to 1232, 1233, 1234,
1235, or 1236.
 Choose an authority level for each area. Not
assigning the authority level for an area denies the
passcode access to that area.
1.
Ensure your keypad shows idle disarmed text.
2.
Press the CMD button. The display shows
*System Command*.
4.
The display changes to show Add / Change
User Enter user #:
5.
Enter the user number and press the ENTER
button.
6.
The display changes to show the user number
entered and the user’s name (if any).
(User 3 is used as an example.)
Press the Continue button to proceed on to
changing the user’s information.
If there is no name for the user, the default user
name text appears in the second line.
(User 3 is used as an example.)
Press the Continue button to change the user’s
information.
7.
The display changes to Add/Change Menu.
The display varies depending on the type of
control panel that was installed in your system.

Door access control in the control panel
(D9412GV2, D9412GV3, D7412GV2,
D7412GV2)
3.
Press the 5 button and then the 6 button.
If you prefer, you might use the function
list in place of Steps 2 and 3 to initiate
this function.

My system does not have door access
control in the control panel (D7212GV3,
D7212GV2)
Press the Menu button to enter the
function list.
Press the Next button repeatedly.
When you reach the Add/Change User
button, press it.
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
49
D1265 | Owner's Manual | Part III: Advanced Commands





If your system has a door access control
available in the control panel, this menu allows
the following User items to be changed:
Passcode - Press the Passcode button to change
the user’s passcode.
Level - Press the Level button to change the
user’s Authority Level.
Name - Press the Name button to change the
user’s name.
Card - Press the Card button to change the
user’s card.
Sub-User - Press the Sub-User button to change
the user’s sub-user status.
Add/Change Passcode
1.
Pressing the Passcode button allows you to
add/change a user’s passcode.
User 3 is used here as an example.
2.
The display changes to User 3 Add/Change a
passcode for this user
Press the Yes button to add a new passcode.
Go to Step 3.
Pressing the No button advances to
Add/Change Level, if the control panel does
not have access control, or Add/Change
Access Card, if the control panel has access
control.
3.
The display changes to Enter new passcode:
Enter the new passcode.



If your system does not have door access
control available in the control panel, this menu
allows the following User items to be changed:
Name - Press the Name button to change the
user’s name.
Passcode - Press the Passcode button to change
the user’s passcode.
Level - Press the Level button to change the
user’s Authority Level.
As soon as a number is pressed, Entering:
appears on the third line next to the asterisks.
The passcode is shown as asterisks (*) when
entered and advance from the right side of the
display to the left until all passcode digits are
entered.
Press the ENTER button.
If the passcode matches the previously enter
passcode, the display changes to Passcode
Added (or Passcode Changed if user exists).
Pressing the Next button advances to the
Add/Change Level (if the control panel does
not have access control) or Add/Change
Access Card (if the control panel has access
control).
50
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
D1265 | Owner's Manual | Part III: Advanced Commands
If a duplicate passcode is entered, the keypad
momentarily reads Passcode is already in use.
Please try again.
The display changes to Enter new passcode
again:
Enter the new passcode again.
If the passcode does not match, the keypad
emits an error tone and shows Passcode not
changed.
Press the ENTER button.
If a duplicate passcode is entered, the keypad
momentarily reads Passcode is already in use.
Please try again.
If the passcode matches the previously entered
passcode, the display changes to Passcode
changed.
Pressing the Next button advances to the
Add/Change Level (if the control panel does
not have access control) or Add/Change
Access Card (if the control panel has access
control).
4.
If the passcode does not match, the keypad
emits an error tone and shows Passcode not
changed.
The display changes to User 3 Change this
user’s passcode.
5.
Press the Exit button to return to the
Add/Change Menu.
Press the Yes button to change the passcode.
Press the No button not to change the passcode
and skip ahead to Add/Change Level (if the
control panel does not have access control)
otherwise if the control panel has access control,
the Add/Change Card appears next.
You are prompted for the user’s passcode.
As soon as a number is pressed, Entering:
appears on the third line next to the asterisks.
It appears on the display as asterisks (*).
Press the ENTER button.
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
51
D1265 | Owner's Manual | Part III: Advanced Commands
Add/Change Level
1.
Pressing the Level button allows you to
add/change a user’s authority level.
2.
The display changes to User 3 Add Auth.
Level for this user.
Press the No button to advance to
Add/Change Passcode (if the control panel
does not have access control) or to Change SubUser ID (if the control panel has access control).
Press the Exit button to exit from this menu
and return to the Level changed display (refer
to Step 6).
If the user is authorized in Area 1, the display
changes to User’s current authority level: 14
for Area 1.
(14 is used as an example here.)
To change the Authority Level, Enter a new
authority level (from 1 to 14), if desired, and
press the ENTER button.
Press the Yes button to add an Authority Level.
Press the No button to advance to Add/Change
Passcode (if the control panel does not have
access control) or to Change Sub-User ID (if the
control panel has access control).
Press the Exit button to exit from this menu
and return to the Level changed display (refer
to Step 6).
The display changes to Is this user authorized
in Area 1?. Press the Yes button to/add change
this user’s authority level in Area 1.
Press the No button if the user isn’t authorized
in Area 1 and proceed to display user’s
authorization in Area 2.
Press the Exit button to exit from this menu
and return to the Level changed display.
If the user is authorized in Area 1, the display
changes to the User’s current authority level: 15
for Area 1 (for example).
Before determining the Authority Level for a
user, please consult your security company to
assist you in selecting the correct authority level.
Press the Exit button to exit from this menu
and return to the Level changed display.
5.
Repeat Step 4 for each area through Area 8.
6.
Once the user’s authority level has been verified
for Area 8, the display changes to Level
changed.
If the Next button is pressed, the display
changes to Add/Change Sub-User ID (if the
control panel has access control).or
Add/Change Passcode (for control panel
without access control).
If the Exit button is pressed, the display
changes to Add / Change User Enter User #:
To change the Authority Level, enter a new
authority level (from 1 to 15), if desired, and
press the ENTER button.
Before determining the Authority Level for a
user, please consult your security company to
assist you in selecting the correct authority level.
Press the Exit button to exit from this menu
and return to the Level changed display.
3.
Repeat Step 2 for each area through Area 8.
4.
The display changes to User 3 Change this
user’s Auth. Level
Press the Yes button to add/change this user’s
authority level in Area 1.
52
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
D1265 | Owner's Manual | Part III: Advanced Commands
Adding/Changing a User’s Name
1.
Another option is to use the numeric buttons to
add characters to the text. For the buttons with
letters, pressing the digit allows you to cycle
through the letters on the button. For instance,
pressing '2' shows an A. Pressing it again shows
a B, and pressing it a third time shows a C.
Pressing the Continue button once you enter a
user changes the display to Add/Change
Menu.
The '0' (zero) button shows a 0. The '1' button
functions like a space bar - it puts a space in the
current position, and advances to the next
position.
2.
Pressing the Name button changes the display.
3.
To change the name use the following buttons:
Pressing this button shows a series of help
screens where the keypad can be used to enter
specific letters.
Pressing either of these buttons causes the
currently underlined character to change the
previous or next character in the list. The
available characters are A-Z, 0-9, @, #, $, and,
*, /, -, _, , and +.
Pressing either of these buttons causes the
cursor of the currently underlined character to
move left to the previous position in the name
or right to the next position in the name.
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
Pressing the button shows a list of the letters for
each digit.
4.
Once the name appears as desired, press the
Continue button.
5.
The display changes to New user name is
GERRY Is this correct?.
At this point you can accept or reject the
changes.
Press the Yes button to accept the name and
return to the idle text screen.
Press the No button to reject the name and
return to Step 2.
53
D1265 | Owner's Manual | Part III: Advanced Commands
Add/Change Card
1.
Pressing the Card button allows you to
add/change a user’s access card or credential.
2.
The display changes to either one of the
following depending on if an access card exists
for the user:
Add/Change Sub-User ID
For each user in the control panel with access control,
there can be up to four access cards; one Master User
(assigned in the Card prompt) and up to three subusers.
1.
Pressing the Sub-User button allows you to
add/change a user’s Sub-User access card or
credential.
2.
The display changes to Add/Change Sub-User
IDs to add or change any of this user’s sub-user
IDs.
User 123 Add Access Card for this user - if no
access card exists for that user.
Pressing the Yes button jumps to Step 3.
Pressing the No button jumps to Add/Change
Passcode.
Pressing the Yes button jumps to Step 3.
3.
Pressing the No button jumps to the
Add/Change Level screen.
Press the Sub-User 1 button to add or change
sub-user 1.
User 123 Change this user’s Access Card - if
an access card already exists for this user and
you wish to change it. (In both cases, 123 is
used as an example).
3.
Press the Sub-User 2 button to add or change
sub-user 2.
Pressing the Yes button jumps to Step 3.
Press the Sub-User 3 button to add or change
sub-user 3.
Pressing the No button jumps to Add/Change
Level.
Press the Exit button to return to the main Add
/ Change User display.
If a card reader is connected to your system, the
display changes to Present card to card
reader now.
4.
If the display changes to D9210 not ready,
contact your security company.
If the card you are trying to add to the system
already exists, an error tone sounds and the
display changes to Card already exists. Please
try again.
Then the display returns to Present card to
card reader now.
5.
If the card is accepted, the display changes to
either Card added or Card changed if the
card already exists in your system.
Pressing the Next button exits from this
function and returns the display to
Add/Change Level.
If adding or changing a sub-user and a card
reader is connected to your system, the display
changes to Add (or Change) Sub-User 1:
Present card to card reader now.
If the display changes to D9210 not ready,
contact your security company.
Pressing the Exit button exits from this function
and returns the display to idle text.
4.
The display changes to Select Sub-User. Do
one of the following:
If 20 sec elapse without pressing a button the
display returns to idle text. Pressing the Exit
button exits from this function and returns the
display to the main Add / Change User
display.
5.
If the card you are trying to add to the system
already exists, an error tone sounds and the
display changes to Card already exists. Please
try again.
If 20 sec elapse without pressing a button
returns the display to idle text. Pressing the Exit
button exits from this function and returns the
display to the main Add / Change User
display.
Press the Exit button to exit from this function
and return the display to idle text.
54
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
D1265 | Owner's Manual | Part III: Advanced Commands
6.
If the card is accepted, the display changes to
either Card added or Card changed if the
card already exists in your system.
Pressing the Exit button exits from this function
and returns the display to the main Add /
Change User display.
Pressing the Next button exits from this
function and returns the display to
Add/Change Passcode depending on if a
passcode already exists for the user.
Default Text (CMD + 5 + 7)
This function allows the current state of the area for 3
sec before returning to idle text.
1.
Ensure your keypad shows idle disarmed text.
2.
Press the CMD button. The display shows
*System Command*.
Fire Test (CMD + 5 + 8)
Use this function to test fire points and other 24-hour
points to be certain they function properly. You can
review both the tested and untested points at your
keypad to help pinpoint any problems.
Upon initiation, the fire test tests the fire bell pattern
on the bell output and ring the keypad fire bell for 2
sec. The AC is disabled for 4 minutes in order to test
the system’s battery power. If the battery cannot
maintain the system for the 4-minute period, the
keypad appears to power off. If this happens, contact
your security company. At the end of the 4-minute
period, AC is returned to the system and the control
panel restores. A message is sent to your security
company upon initiation and completion of the Fire
Test. During the Fire Test, no 24-hour alarms are
sent to your security company.
If there is no activity on the system for 20 minutes, the
system automatically exits from the Fire Test.
Any 24-hour points left in a faulted condition at the
end of the test are automatically removed from service
by bypassing them. Once the 24-hour device is reset to
normal, use the Unbypass command (refer to Unbypass
A Point (CMD + 0 + 0) on page 33) to return them to
service.
3.
Press the 5 button and then the 7 button.
If you prefer, you might use the function
list in place of Steps 2 and 3 to initiate
this function.
Using Fire Test
1.
Ensure your keypad shows idle disarmed text.
2.
Press the CMD button. The display shows
*System Command*.
3.
Press the 5 button and then the 8 button.
Press the Menu button to enter the
function list.
Press the Next button repeatedly.
When you reach the Default Text button,
press it.
4.
The current state of the area is shown for 3 sec
before returning to idle text.
If you prefer, you might use the function
list in place of Steps 2 and 3 to initiate
this function.
Press the Menu button to enter the
function list.
Press the Next button repeatedly.
When you reach the Fire Walk Test
button, press it.
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
55
D1265 | Owner's Manual | Part III: Advanced Commands
4.
When the display shows ### points remain to
be tested you can begin. (### is the number of
points).
7.
Test each point by first activating the detection
device to fault the point.
The display shows ### pts untested.
If you know the point number, you can
enter it by pressing its number button and
then the ENTER button.
Press the Point information button to see
information about specific points that have not
yet been tested.
The display changes to show the point
that was entered. If the point is invalid the
message “Invalid Point” or “This is not a
valid walk point” appears.
5.

As you fault each point, your keypad shows the
point text for 60 sec and ring the fire sounders
for 2 sec. This verifies that the detection device
is working properly. Your system automatically
resets smoke detectors.
When a resettable point (such as a smoke
detector) is faulted, the display shows
Sensors…resetting…please wait… for 5 sec.
During this time power is removed from smoke
power relays.

Faulting a point more than once will not
increment the test count. However, the keypad
emits a brief tone and shows the point text each
time you fault the point allowing you to test
multiple devices assigned to one point.
6.
When the point has been tested, the display
changes to show SMOKE DETECTOR tested.
56
During the Fire Test you might want to refer to
the points that remain untested by pressing the
View untested pts button.
The display changes to show the information
for that point.
Move through this list by pressing the Next
Point button.
Press the Exit button to return to the ###
points remain to be tested before continuing
the Fire Test.
8.
When all 24-hour points have been tested, 0
points remain to be tested is shown.
Press the Exit button.
The display momentarily shows All points
have been tested before returning to idle text.
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
D1265 | Owner's Manual | Part III: Advanced Commands
Display Rev (CMD + 5 + 9)
1.
Ensure your keypad shows idle disarmed text.
2.
Press the CMD button. The display shows
*System Command*.
3.
Press the 5 button and then the 9 button.
If you prefer, you might use the function
list in place of Steps 2 and 3 to initiate
this function.
Press the Menu button to enter the
function list.
Press the Next button repeatedly.
When you reach the Display Revision
button, press it.
4.
The display changes to *BOSCH D7412GV2*.
(D7412GV2 is used as an example, other
control panels could be
D9412GV3/D9412GV2, D7412GV3,
D7212GV3/D7212GV2.)
5.
The display returns to idle text after 5 sec.
Service Menu (9 + 9 + Enter)
The service menu is used to access the following
commands:
 View Log - Use this function to review events in
your system at your keypad. Reviewing past events
might help you identify problems. Viewing events
will not require any additional equipment since the
information is shown at your keypad. Events are
stored in the control panel’s memory in order of
occurrence and tagged with the date and time.
 Print Log - The Print Log function lets you print
the events stored in your security system’s log. You
can choose to print the entire log or set a start date
and print the events recorded from that date up to
today. Your system must include a parallel printer
interface and a printer to perform this function.
 Display Rev (COMMAND + 5 + 9) - The
command retrieves the control panel’s software
version and display it.
 Service Walk (D9412/D9112 only) – The
command allows all the points on the system to be
walk tested regardless of the type of point. For
D7412GV3/D7412GV2 and
D7212GV3/D7212GV2 Control Panels this
function must be added to the keypad’s menu.
Contact your security company for more
information.
 Default Text – This command shows the current
state of the area for 3 sec before returning to idle
text.
 Keypad Programming - This optional command
is only included in this menu when enabled and
when all areas are disarmed. Access is restricted to
the Service User only. Through this menu, you can
change a limited selection of system configuration
parameters. Consult your security company for
details.
1.
Ensure your keypad shows idle disarmed text.
2.
Press the 9 button twice.
3.
Press the ENTER button.
4.
The display changes to show the service menu.
Service Walk Test appears on D9412GV2 and
D9412GV3 control panels only.
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
57
D1265 | Owner's Manual | Part III: Advanced Commands
Using View Log
1.
2.
3.
Press the View Log button.
The display changes to Enter start date:
Using Print Log
1.
Press the Print Log button.
2.
The display changes to Enter start date:
Press the Go to last event button to go to the
last event in the log.
Press the Print all events button to print all
events in the log.
Press the Exit button to exit this function and
return to idle text.
Enter the start date in the form of mm/dd.
Press the Exit button to exit this function and
return to idle text.
The events are sent to a connected printer and
display changes to Printing all events in
history for 3 sec before returning to idle text.
For example, to enter 7/14 as the start date,
press 0 + 7 + 1 + 4
Once you start entering digits, the Go to last
event button is replaced with the ENTER
button.
4.
6.
3.
Enter the start date in the form of mm/dd.
For example, to enter 12/21 as the start date,
press 1 + 2 + 2 + 1.
Press the Exit button to exit this function and
return to idle text.
Press the ENTER button.
Once you start entering digits, the Print all
events button is replaced with the ENTER
button.
If the date entered is valid, the first event for
that date appears.
Press the Exit button to exit this function and
return to idle text.
If the date entered is invalid (there are no
events with that date in the log), it shows the
next latest event in the log.
Press the Exit button to exit this function and
return to idle text.
7.


The display shows one of two ways depending
on if the date entered was for an event first in
the log or not.
If the date was for the first event in the log, it
shows the next latest event in the log.
If the date was for an event (not the first) in the
log, the display is the same except the Previous
button has been added.
Press the ENTER button.
4.
If the date entered is valid, the events for that
date is sent to a connected printer and the
display shows Printing events. for 3 sec, before
returning to idle text.
Using Display Revision
1.
Press the Display Revision button.
2.
The display changes to show the revision
number.
3.
The display returns to idle text after 5 sec.
Press the Exit button to exit this function and
return to idle text.
8.
Press the Next button to go to the next event in
the log.
If there are no more events in the log, *End of
Log* appears.
Press the Previous button to go to the previous
event in the log.
Press the Exit button to exit this function and
return to idle text.
58
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
D1265 | Owner's Manual | Part III: Advanced Commands
Using Service Walk Test
The Service Walk Test function is only
available in the Service Menu for
D9412GV3/D9412GV2 control panels. If
the control panel model is
D7212GV3/D7212GV2, you must enable
the Service Walk Test on the Function list
for the keypad through the control panel’s
programming.
1.
When the display shows ### points remain to
be tested you can begin. (### is the number of
points).
If you know the point number, you can
enter it by pressing its number button and
then the ENTER button.
The display changes to show the point
that was entered. If the point is invalid the
message “Invalid Point” or “This is not a
valid walk point” appears.
Test each point by first opening and then
closing the door or window or other detection
device.
Check the display after testing each point. For
interior points, walking past the device once is
sufficient. If any point will not test correctly,
contact your security company for service.
2.
During the Walk Test you might want to refer
to the points that remain untested by pressing
the View untested pts button.
The display shows ### pts untested.
Press the Point information button to see
information about specific points that have not
yet been tested.
Using Default Text
This function allows the current state of the area for 3
sec before returning to idle text.
1.
Press the Default Text button to display the
current state of the area.
2.
The current state of the area is shown for 3 sec
before returning to idle text.
Keypad Setup Menu
The Keypad Setup menu is accessible at anytime
from any keypad menu. To start the menu, press and
hold the 0 button for at least 5 sec.
The adjustable functions that are available in this menu
are:
 Set the keypad’s SDI Bus address

Adjust the keypad volume and display
brightness
 Turn the button click tone on or off
 Set the screen on time
Use the up and down buttons for each function to
change the setting for the options:

Keypad Address, SDI bus address

Keypad Volume. Applies to low priority tones
only

Button Click. Key press acknowledgement

Brightness

Screen On Time. Time in minutes before
power saving mode activates.
Press Save to save your changes when finished. The
display returns to idle text. Press Back to exit the
menu.
The display changes to show the information
for that point.
Move through this list by pressing the Next
Point button.
Press the Exit button to return to the ###
points remain to be tested before continuing
the Service Walk Test.
3.
When all points have been tested, 0 points
remain to be tested is shown.
Press the Exit button.
The display momentarily shows All points
have been tested before returning to idle text.
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
59
D1265 | Owner's Manual | Part IV: Multi-Area Use
Part IV: Multi-Area Use
Working with Multiple Areas from a Single
Keypad
Each of the functions described in the preceding
section on Advanced Commands is presented as
though your system includes only one area. If your
system includes more than one area, it can be set up in
one of two ways by the installing company:
 Each keypad only has access to the local area to
which it is assigned, or
 Each keypad might access either some or all areas
beyond the one to which it is assigned. This factor
is referred to hereafter as keypad scope.
If your keypad allows access to areas other than the
local area (that is to say, has scope in other areas), then
the keypad limits your access to those areas within the
keypad scope and for which your personal passcode
has authority.
Given that you have access to areas beyond the local
area, the means of accessing the various system
functions depends upon the specific function.
For some functions, the keypad allows you to select the
area (or point) in which to perform the function. These
“selectable” functions are:
 Disarm
 Master Arm Area
 Bypass A Point
 Unbypass A Point
Another group of functions might automatically work
in all areas in which you have passcode authority and
which are within the scope of the keypad. These are:
 Turning Off Multiple Areas with a Passcode
 Disarm All
 Master Arm All
 View Alarm Memory
 Walk Test
 Reset Sensors
 Add Passcodes
 Fire test
 View Point Status
 View Area Status
Some functions might be area-specific. To perform
these functions, you must first use the Move To Area
function (CMD 50) to gain access to the desired area.
Once in the desired area you can perform the
functions you wish. Area-specific functions include:
 Perimeter Instant (Perimeter On Instant)
 Perimeter Delay (Perimeter On Delay)
 Perimeter Partial (Perimeter On Partial)
 Extend Closing
60
 Watch Mode
 CMD 7
 CMD 9
A last group of functions don’t relate to specific areas
and are thus system-wide. These are:
 Send Report
 Remote Program
 Change Time/Date
 Change Skeds
 Delete Passcodes
 Change Relays
 Change Passcodes
 Print Log
 View Log
View Area Status
Use this function when you need to know the status
(whether armed or disarmed) of areas other than the
one you’re in.
1.
Ensure your keypad shows idle disarmed text.
2.
Press the Menu button to enter the function list.
3.
Press Next repeatedly until you reach the View
Area Status button.
Press the button.
4.
The display changes to show on the top line the
area name and the current status on the second
line.
Pressing the Next button changes the display to
the next area and remain for 20 sec or until the
Next button is pressed for the next area. If the
time has elapsed, the display returns to idle text.
Pressing the Previous button changes the
display to the previous area.
5.
Press the Exit button to return to idle text.
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
D1265 | Owner's Manual | Part IV: Multi-Area Use
View Point Status
Use this function to identify the number or location of
each point in an area, and to show the current
condition of any point you select.
1.
Ensure your keypad shows idle disarmed text.
2.
Press the Menu button to enter the function list.
3.
Press Next repeatedly until you reach the View
Point Status button.
Press the button.
4.
In this example, Area 1 is the area and there are
five points assigned to area 1 that can be
viewed.
Table 5: Screen Area Definitions
Line #
1
Area
Name
Point text
2
Area #
Pt #
3
(Point
State),
HW
Definition
This displays the customized name
for the point.
This displays the area number.
This displays point numbers 1 to
127 and 129 to 247.
Normal
Indicates that the point
is not in the faulted
state.
Open
Indicates that the point
is in an open state.
Short
Indicates that the point
is in a shorted state.
Missing
Indicates that the point
is missing.
Press the Next button to view the first point in
the last area; press the Previous button to view
the last point in the area. You can press the Exit
button at any time to exit this function.
5.
The top line shows the point text. The second
line shows the area assignment of the current
point and the point number. The third line
shows the points current state {Normal, Open,
Short, Missing}.shows the point text.
Pressing the Next button takes you to the next
point in the area whereas the Previous button
takes you to the previous point in the area.
6.
Refer to Table 5 for more information.
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
61
D1265 | Owner's Manual | Part IV: Multi-Area Use
Move To Area (CMD + 5 + 0)
If the user's authority level will not permit
access to a certain area and that area is
not within the scope of the keypad, or the
area is not enabled, it will not appear in
the display.
With this function you can perform tasks in an area
other than the one you’re in without having to
physically go to that area. Your access to other areas is
limited by the scope of the keypad and your authority
level. For example, if your passcode gives you
authority to all areas supported by the control panel,
but the keypad you’re working with is limited in scope
to areas 1 and 2, then you only can move to either area
1 or area 2.
Upon moving to another area, the range of tasks you
might perform depends upon the keypad you’re
working with. Once you have performed a task (such
as Turning the Area On), the keypad reverts back to its
programmed area after 10 sec. Thus only one task can
be performed in another area at a time.
1.
Ensure your keypad shows idle disarmed text.
2.
Press the CMD button. The display shows
*System Command*.
If the area you wish to move to will not appear
in this list, press the Next button to display
additional areas.
6.
7.
8.
To select an area, simply press the button
corresponding to the Area Name.
Moving to…AREA 1 WAREHOUSE shows
briefly, and then the text of the area you have
moved to is shown (AREA 1 WAREHOUSE is
used as an example here).
You are now able to perform tasks in this area.
The number of areas to which you can move is
limited by the scope of the keypad.
When you have completed all tasks in the area
you have moved to, simply allow the keypad to
time-out and revert to the area from which you
started or enter the Move to Area function
again.
Turning On the System
Turning on Selected Areas
3.
Press the 5 button and then the 0 button.
If you prefer, you might use the function
list in place of Steps 2 and 3 to initiate
this function.
Areas covered in the scope of the keypad can be
armed individually by accessing the Master Arm
function through the menu.
1.
Press the Menu button to enter the function list.
2.
Press the Next button repeatedly until you
reach the Master Arm button, and then press
it.
3.
You might be prompted for your passcode. It
appears on the display as asterisks (*).
Press the Menu button to enter the
function list.
Press the Next button repeatedly.
When you reach the Move To Area
button, press it.
4.
5.
62
You might be prompted for your passcode. If so,
enter your passcode and press the ENTER button.
It appears on the display as asterisks (*).
The Exit button quits this function and return to
idle text.
The keypad shows the Area Name Text of each
area that falls within the scope of the keypad and
authority level of the user, if applicable.
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
D1265 | Owner's Manual | Part IV: Multi-Area Use
4.




The display changes and shows Master Arm
All with the following options:
Previous button– scrolls to the last area that
can be armed (based on passcode and authority
level)
Next button – scrolls to the first area that can
be armed (based on passcode and authority
level)
Arm button – arms all areas (based on passcode
and authority level)
Exit button – returns the display to idle text
2.
Keypad scope and/or your authority level limit
the actual number of areas you might turn on.
For example, if you have authority to arm all
areas but the scope of the keypad you’re using
is limited to areas 1, 2, and 5, then you only can
turn on areas 1, 2, and 5.
3.
5.
6.
If the Next button is pressed, the first area that
can be armed (based on passcode entered and
user authority level) is shown (AREA 1
WAREHOUSE is used an example of the first
area that can be armed).
Pressing the Arm button causes AREA 1
WAREHOUSE is now arming… to display for
3 sec before the prompt to arm the next
available area is shown.
Turning on Multiple Areas with a Passcode
You can use your personal passcode to turn on both
perimeter and interior points in all areas where your
passcode has authority. If there are areas already
turned on, this function rearms those areas in addition
to turning on all authorized areas that are currently off.
1.
Enter your passcode and press ENTER.
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
The keypad shows the following:
If a point is faulted (door or window open for
example). Refer to Turning On the System
(Arming) With Doors or Windows Open on page 17
for more information.
Faulted Points in Other Areas
If there is a faulted point in an area you select (other
than the one you are in), Check Area 1 (1 is used as
an example here) appears for 3 sec and then the
display returns to the area disarmed idle text.
If there is a faulted point in more than one area and
the system is being armed, the display prompts Check
Area 1 3 meaning there are faulted points in Areas 1
and 3.
Try one of the following:

Clear faulted points (close doors and/or windows)
and return to step 1.

Bypass faulted points (if your system and/or
authority allows) and return to step 1.

Force arm (if your system and/or authority allows).
Refer to Turning On the System (Arming) With Doors
or Windows Open on page 17 for more information.
63
D1265 | Owner's Manual | Part IV: Multi-Area Use
Turn On the Entire System Without Delays
6.
Pressing the Arm button causes AREA 1
WAREHOUSE is now arming… to display for
3 sec before the prompt to arm the next
available area is shown.
7.
To instantly arm all the areas that are within the
scope of the keypad, press the Arm button.
8.
This display changes to show On Instant
indicating that the areas are armed.
You can use this function list function to turn on the
entire system, both perimeter and interior, without
delays. You might use this function in all of the areas
or some of the areas where your passcode has
authority. If there are areas already turned on, this
function rearms those areas in addition to turning on
(without delay) all authorized areas that are currently
off.
Turning on All or Selected Areas
Areas covered in the scope of the keypad can be
armed individually by accessing the Master Arm
function through the menu.
1.
Press the Menu button to enter the function list.
2.
Press the Next button repeatedly until you
reach the Master Arm Instant button, and then
press it.
3.
You might be prompted for your passcode. It
appears on the display as asterisks (*).
4.
The display changes and shows Master Arm
All with the following options:
Previous button– scrolls to the last area that
can be armed (based on passcode and authority
level)
Next button – scrolls to the first area that can
be armed (based on passcode and authority
level)
Arm button – arms all areas (based on passcode
and authority level)
Exit button – returns the display to idle text




5.
64
If the Next button is pressed, the first area that
can be armed (based on passcode entered and
user authority level) is shown (AREA 1
WAREHOUSE is used an example of the first
area that can be armed).
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
D1265 | Owner's Manual | Part IV: Multi-Area Use
Turning Off the System
4.
If entering through a door which is part of an
area that is armed, the display instructs you to
enter your passcode to disarm.
5.
Enter your passcode and press ENTER.
Turning Off Multiple Areas with a Passcode
This function is useful for turning off multiple areas
with a few button presses. It is quicker than disarming
several areas independently. Your passcode must have
the proper authority level for each area.
 After enter your passcode, the following shows
Disarm: 12345678 All user-authorized areas are
now disarmed. (Not all area number might
appear due to what areas are in the scope of the
keypad.
The passcode is shown as asterisks (*) when
entered and advance from the right side of the
display to the left until all the passcode digits
are entered.
6.
If the entered passcode is valid, the display
changes to show Disarm All.

When an area is turned on (armed), you must
enter a door programmed for entry delay time.
Opening the door, starts the entry delay time.
Failing to turn off the system before the entry
delay time expires or entering through a door not
programmed for entry delay time, causes an alarm.
 If this happens, silence the alarm by entering your
personal passcode and pressing ENTER. Call your
security company to let them know that it is not an
emergency situation.
Turning Off Multiple Areas with Disarm All
 This function turns off multiple areas with a few
button presses. It is quicker than disarming several
areas independently. Your passcode must have the
proper authority level for each area. This function
works the same as entering your passcode to
disarm, but allows the Disarm All feature to be
included in the function list.
 When an area is turned on (armed), you must
enter a door programmed for entry delay time.
Opening the door, starts the entry delay time.
Failing to turn off the system before the entry
delay time expires or entering through a door not
programmed for entry delay time, causes an alarm.
 If this happens, silence the alarm by entering your
personal passcode and pressing ENTER. Call your
security company to let them know that it is not an
emergency situation.
1.
The display initially shows that the system is
armed.
2.
Press the Menu button to enter the function list.
3.
Press the Next button repeatedly until you
reach the Disarm Menu button, then press it.
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
Press the Disarm button to disarm all armed
areas.
Press the Next button to go to the first armed
area (refer to Turning Off Selected Areas on page
66).
Press the Previous button to go to the last
armed area.
Press the Exit button to return to idle text.
7.
If the Disarm button is pressed to disarm all
areas, the display changes to show Disarm:
12345678 All user-authorized areas are now
disarmed indicating that all areas are being
turned off. Keypad scope and/or your authority
level limit the actual number of areas you might
turn off.
For example, if you have authority to disarm all
8 areas but the scope of the keypad you’re using
is limited to areas 1, 2, and 5, then you only can
turn off areas 1, 2, and 5.
65
D1265 | Owner's Manual | Part IV: Multi-Area Use
Turning Off Selected Areas
If your passcode has the proper authority level this
function allows you to turn off areas other than the one
you are in.
1.
The display initially shows that the system is
armed.
2.
Press the Menu button to enter the function list.
3.
Press the Next button repeatedly until you
reach the Disarm Menu button, and then press
it.
4.
If entering through a door which is part of an
area that is armed, the display changes to show:
5.
Enter your passcode and press ENTER.
The passcode is shown as asterisks (*) when
entered and advance from the right side of the
display to the left until all the passcode digits
are entered.
6.
If the entered passcode is valid, the display
changes to show Disarm All.
7.
Press the Next button to go to the first armed
area.
8.
The display changes to show Disarm Area 1
(or the first area that is armed).
Press the Disarm button to disarm this area. A
confirmation of the areas disarmed status is
shown, and then the display advances to the
next armed area.
Press the Next button to scroll through the
remaining areas you have the authority to turn
off.
To disarm the area, press the Disarm button.
9.
66
After turning off all armed areas or pressing the
Exit button, the keypad’s display returns to the
idle text for the area you are in.
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
D1265 | Owner's Manual | Appendix
If you are having trouble understanding the concept of
authority levels, try this simple exercise. Refer to the
column titled E/P in the User Interface section starting
on page 67. Notice that your security technician has
marked some of the cells in this column with the letter
“E”, others the letter “P”, while others are left blank.
An “E” indicates that this function is enabled for all
authority levels. A “P” indicates that the function is
passcode protected. Look across the same row, and
notice that some of the cells in the authority level area
have the letter “E”. For each authority level in which
an “E” appears, this function is enabled (with a
passcode required). A blank cell in the E/P column
means that this function is unavailable for any
authority level.
Appendix
Supplementary Information for Adding
Passcodes
Use the information contained in this Supplement to
help you add user passcodes.
User Authority Levels
Your security company uses the information contained
on this page to establish authority levels for system
users. For each of the 1- 14 authority levels, each
keypad function is either enabled (E), disabled (blank),
or Passcode enabled (P). A function that is enabled (E)
is available to all users. A function that is passcode
enabled (P) is only available to users assigned an
authority level that includes that function. If you do not
want a particular command included in a given
authority level, leave it blank.
Under the heading Authority Level, you’ll refer to
columns 1-14, representing the fourteen authority
levels. Now look at the column labeled 1. Following
down this column, you’ll refer to that some cells are
blank while some contain the letter “E”, which stands
for enabled. Wherever there is an “E”, it means that
that function is available to users with an authority
level of 1.
Passcode Worksheet
The passcode worksheet presents the information discussed previously onto one page, and also includes the user’s
ID number, assigned passcode, and his or her name.
An important piece of information included in the passcode worksheet is the listing of areas to which the user has
access, along with the authority level assignment for each of those areas.
User Interface
Authority Levels
#
Functions*
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Disarm
Master Arm Delay
Master Arm Instant
Perimeter Instant
Perimeter Delay
Watch Mode
Perimeter Part
View Area Status
View Memory
View Pt Status
Walk Test
Fire Test
Send Report
Door Control
Cycle Door
Unlock Door
Secure Door
Access Control Level
Change Display
Change Time/Date
Change Passcode
Add User
Del User
37
15
16
17
18
19
Command
CMD 1
CMD 11
CMD 2
CMD 3
CMD 6
CMD 8
CMD 40
CMD 44
CMD 58
CMD 41/42
CMD 46
CMD 49
CMD 45
CMD 55
CMD 56
CMD 53
E/P
1
2
3
4
5
P
P
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
P
P
E
P
P
E
E
E
P
P
P
E
E
E
P
E
E
P
P
P
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
6
7
8
9
10
11
12
13
14
E
E
E
67
D1265 | Owner's Manual | Appendix
Authority Levels
20
21
22
23
24
25
26
27
28
29
30
32
33
34
35
36
Extend Close
View Log
Print Log
User Command 7
User Command 9
Bypass a Point
Unbypass a Point
Reset Sensors
Change Relays
Remote Program
Move To Area
Display Rev
Service Walk
Default Text
Change Skeds
Invisible Walk Test
CMD 51
CMD 7
CMD 9
CMD 0
CMD 00
CMD 47
CMD 54
CMD 43
CMD 50
CMD 59
CMD 57
CMD 52
P
E
P
P
P
P
P
E
P
P
P
E
P
P
P
P
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
* Keypad Function Authority Level Options: Blank = Disabled, E = Enabled.
 D9412GV3/D7412GV3/D9412GV2/D7412GV2 only.
Authority Level 15 can not be edited.
User Interface
Authority Levels
#
Functions*
#
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
Custom Functions
Custom Function 128
Custom Function 129
Custom Function 130
Custom Function 131
Custom Function 132
Custom Function 133
Custom Function 134
Custom Function 135
Custom Function 136
Custom Function 137
Custom Function 138
Custom Function 139
Custom Function 140
Custom Function 141
Custom Function 142
Custom Function 143
Command
E/P
1
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
D
M
I
2
3
4
5
6
M
D
P
D
P
D
P
D
D
7
8
9
10
11
12
13
14
Access Levels**
 Security Level
 Disarm Level
 Function Level
* Keypad Function Authority Level Options: Blank = Disabled, E = Enabled.
Authority Level 15 can not be edited.
 D9412GV3/D7412GV3/D9412GV2/D7412GV2 only.
** Access Authority Level Options:
Security Level
M = Any Armed State, P = Perimeter Armed, D = Disarmed, Blank = No Access
Disarm Level
I = Disarm to Perimeter Instant, D = Disarm All, Blank = No Disarm Rights
Function Level
Function Level M = Any Armed State, D = Disarmed state, C = Any Armed
state, Blank = Function disabled
68
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
D1265 | Owner's Manual | Appendix
User (Passcode) Worksheet (User 000 to 038)
User
###
Passcode
User
Group
Note: Text shown in Times font (ex. 15) indicates sample text.
Area Authority
1
2
3
4
5
6
7
8
User Name
15
15
15
15
15
15
15
15
SERVICE
000
1 2 3 __ __ __
001
123456 ________
____
1_
__
__
__
__
__
__
__
USER 1
002
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 2
003
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 3
004
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 4
005
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 5
006
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 6
007
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 7
008
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 8
009
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 9
010
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 10
011
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 11
012
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 12
013
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 13
014
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 14
015
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 15
016
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 16
017
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 17
018
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 18
019
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 19
020
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 20
021
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 21
022
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 22
023
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 23
024
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 24
025
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 25
026
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 26
027
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 27
028
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 28
029
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 29
030
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 30
031
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 31
032
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 32
033
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 33
034
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 34
035
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 35
036
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 36
037
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 37
038
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 38
PASSCODE
Product Handler Note: RADXUSR1 is for Users 000 - 124; RADXUSR2 is for Users 125 - 249.
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
69
D1265 | Owner's Manual | Appendix
 User (Token) Worksheet (User 000 to 038) D9412GV3/D7412GV3/D9412GV2/D7412GV2 Only
Use
r
Master ID ###-0
Sub-User ###-1
Sub-User ###-2
Sub-User ###-3
###
Site
Site
Site
Site
000
Not Available
Card Data
Card Data
Card Data
Card Data
001
002
003
004
005
006
007
008
009
010
011
012
013
014
015
016
017
018
019
020
021
022
023
024
025
026
027
028
029
030
031
032
033
034
035
036
037
038
70
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
D1265 | Owner's Manual | Appendix
User (Passcode) Worksheet (User 039 to 075)
User
User
Area Authority
###
Passcode
Group
1
2
3
4
5
6
7
8
039
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 39
040
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 40
041
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 41
042
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 42
043
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 43
044
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 44
045
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 45
046
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 46
047
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 47
048
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 48
049
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 49
050
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 50
051
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 51
052
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 52
053
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 53
054
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 54
055
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 55
056
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 56
057
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 57
058
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 58
059
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 59
060
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 60
061
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 61
062
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 62
063
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 63
064
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 64
065
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 65
066
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 66
067
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 67
068
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 68
069
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 69
070
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 70
071
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 71
072
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 72
073
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 73
074
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 74
075
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 75
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
User Name
71
D1265 | Owner's Manual | Appendix
 User (Token) Worksheet (User 039 to 075) D9412GV3/D7412GV3/D9412GV2/D7412GV2 Only
User
###
Master ID ###-0
Site
Card Data
Sub-User ###-1
Site
Card Data
Sub-User ###-2
Site
Card Data
Sub-User ###-3
Site
Card Data
039
040
041
042
043
044
045
046
047
048
049
050
051
052
053
054
055
056
057
058
059
060
061
062
063
064
065
066
067
068
069
070
071
072
073
074
075
72
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
D1265 | Owner's Manual | Appendix
User (Passcode) Worksheet (User 076 to 114) (101-249 = D9412GV3/D9412GV2 only)
User
###
Passcode
076
__ __ __ __ __ __
077
__ __ __ __ __ __
078
__ __ __ __ __ __
079
__ __ __ __ __ __
080
__ __ __ __ __ __
081
__ __ __ __ __ __
082
__ __ __ __ __ __
083
__ __ __ __ __ __
084
__ __ __ __ __ __
085
__ __ __ __ __ __
086
__ __ __ __ __ __
087
__ __ __ __ __ __
088
__ __ __ __ __ __
089
__ __ __ __ __ __
090
__ __ __ __ __ __
091
__ __ __ __ __ __
092
__ __ __ __ __ __
093
__ __ __ __ __ __
094
__ __ __ __ __ __
095
__ __ __ __ __ __
096
__ __ __ __ __ __
097
__ __ __ __ __ __
098
__ __ __ __ __ __
099
__ __ __ __ __ __
100
__ __ __ __ __ __
101
__ __ __ __ __ __
102
__ __ __ __ __ __
103
__ __ __ __ __ __
104
__ __ __ __ __ __
105
__ __ __ __ __ __
106
__ __ __ __ __ __
107
__ __ __ __ __ __
108
__ __ __ __ __ __
109
__ __ __ __ __ __
110
__ __ __ __ __ __
111
__ __ __ __ __ __
112
__ __ __ __ __ __
113
__ __ __ __ __ __
114
__ __ __ __ __ __
User
Group
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
1
2
Area Authority
3
4
5
6
7
8
__
__
__
__
__
__
__
__
USER 76
__
__
__
__
__
__
__
__
USER 77
__
__
__
__
__
__
__
__
USER 78
__
__
__
__
__
__
__
__
USER 79
__
__
__
__
__
__
__
__
USER 80
__
__
__
__
__
__
__
__
USER 81
__
__
__
__
__
__
__
__
USER 82
__
__
__
__
__
__
__
__
USER 83
__
__
__
__
__
__
__
__
USER 84
__
__
__
__
__
__
__
__
USER 85
__
__
__
__
__
__
__
__
USER 86
__
__
__
__
__
__
__
__
USER 87
__
__
__
__
__
__
__
__
USER 88
__
__
__
__
__
__
__
__
USER 89
__
__
__
__
__
__
__
__
USER 90
__
__
__
__
__
__
__
__
USER 91
__
__
__
__
__
__
__
__
USER 92
__
__
__
__
__
__
__
__
USER 93
__
__
__
__
__
__
__
__
USER 94
__
__
__
__
__
__
__
__
USER 95
__
__
__
__
__
__
__
__
USER 96
__
__
__
__
__
__
__
__
USER 97
__
__
__
__
__
__
__
__
USER 98
__
__
__
__
__
__
__
__
USER 99
__
__
__
__
__
__
__
__
USER 100
__
__
__
__
__
__
__
__
USER 101
__
__
__
__
__
__
__
__
USER 102
__
__
__
__
__
__
__
__
USER 103
__
__
__
__
__
__
__
__
USER 104
__
__
__
__
__
__
__
__
USER 105
__
__
__
__
__
__
__
__
USER 106
__
__
__
__
__
__
__
__
USER 107
__
__
__
__
__
__
__
__
USER 108
__
__
__
__
__
__
__
__
USER 109
__
__
__
__
__
__
__
__
USER 110
__
__
__
__
__
__
__
__
USER 111
__
__
__
__
__
__
__
__
USER 112
__
__
__
__
__
__
__
__
USER 113
__
__
__
__
__
__
__
__
USER 114
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
User Name
73
D1265 | Owner's Manual | Appendix
 User (Token) Worksheet (User 076 to 114) D9412GV3/D7412GV3/D9412GV2/D7412GV2 Only (101-249
= D9412GV3/D9412GV2 only)
User
###
Master ID ###-0
Site
Card Data
Sub-User ###-1
Site
Card Data
Sub-User ###-2
Site
Card Data
Sub-User ###-3
Site
Card Data
076
077
078
079
080
081
082
083
084
085
086
087
088
089
090
091
092
093
094
095
096
097
098
099
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
74
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
D1265 | Owner's Manual | Appendix
User (Passcode) Worksheet (User 115 to 150) (101-249 = D9412GV3/D9412GV2 only)
User
User
###
Passcode
115
Group
Area Authority
1
2
3
4
5
6
7
8
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 115
116
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 116
117
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 117
118
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 118
119
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 119
120
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 120
121
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 121
122
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 122
123
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 123
124
__ __ __ __ __
__
__ __ __ __ __ __
End RADXUSR1 Handler
__
USER 124
125
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 125
126
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 126
127
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 127
128
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 128
129
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 129
130
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 130
131
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 131
132
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 132
133
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 133
134
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 134
135
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 135
136
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 136
137
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 137
138
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 138
139
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 139
140
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 140
141
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 141
142
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 142
143
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 143
144
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 144
145
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 145
146
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 146
147
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 147
148
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 148
149
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 149
150
__ __ __ __ __
__
__
__
__
__
__
__
__
USER 150
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
User Name
75
D1265 | Owner's Manual | Appendix
User (Token) Worksheet (User 115 to 150) (101-249 = D9412GV3/D9412GV2 only)
User
###
Master ID ###-0
Site
Card Data
Sub-User ###-1
Site
Card Data
Sub-User ###-2
Site
Card Data
Sub-User ###-3
Site
Card Data
115
116
117
118
119
120
121
122
123
124
End RADXUSR1 Handler
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
76
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
D1265 | Owner's Manual | Appendix
User (Passcode) Worksheet (User 151 to 189) (101-249 = D9412GV3/D9412GV2 only)
User
###
Passcode
User
Group
1
2
Area Authority
3
4
5
6
7
8
151
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 151_
152
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 152_
153
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 153_
154
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 154_
155
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 155_
156
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 156_
157
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 157_
158
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 158_
159
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 159_
160
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 160_
161
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 161_
162
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 162_
163
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 163_
164
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 164_
165
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 165_
166
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 166_
167
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 167_
168
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 168_
169
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 169_
170
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 170_
171
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 171_
172
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 172_
173
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 173_
174
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 174_
175
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 175_
176
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 176_
177
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 177_
178
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 178_
179
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 179_
180
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 180_
181
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 181_
182
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 182_
183
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 183_
184
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 184_
185
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 185_
186
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 186_
187
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 187_
188
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 188_
189
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 189_
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
User Name
77
D1265 | Owner's Manual | Appendix
User (Token) Worksheet (User 151 to 189) (101-249 = D9412GV3/D9412GV2 only)
User
Master ID ###-0
Sub-User ###-1
Sub-User ###-2
Sub-User ###-3
###
Site
Site
Site
Site
Card Data
Card Data
Card Data
Card Data
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
78
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
D1265 | Owner's Manual | Appendix
User (Passcode) Worksheet (User 190 to 226) (101-249 = D9412GV3/D9412GV2 only)
User
###
Passcode
User
Group
Area Authority
1
2
3
4
5
6
7
8
User Name
190
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 190
191
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 191
192
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 192
193
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 193
194
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 194
195
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 195
196
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 196
197
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 197
198
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 198
199
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 199
200
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 200
201
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 201
202
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 202
203
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 203
204
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 204
205
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 205
206
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 206
207
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 207
208
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 208
209
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 209
210
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 210
211
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 211
212
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 212
213
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 213
214
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 214
215
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 215
216
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 216
217
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 217
218
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 218
219
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 219
220
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 220
221
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 221
222
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 222
223
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 223
224
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 224
225
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 225
226
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 226
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
79
D1265 | Owner's Manual | Appendix
 User (Token) Worksheet (User 190 to 226) D9412GV3/D7412GV3/D9412GV2/D7412GV2 Only (101-249
= D9412GV3/D9412GV2 only)
User
###
Master ID ###-0
Site
Card Data
Sub-User ###-1
Site
Card Data
Sub-User ###-2
Site
Card Data
Sub-User ###-3
Site
Card Data
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
80
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
D1265 | Owner's Manual | Appendix
User (Passcode) Worksheet (User 227 to 249) (101-249 = D9412GV3/D9412GV2 only)
User
User
Area Authority
###
Passcode
Group
1
2
3
4
5
6
7
8
User Name
227
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 227
228
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 228
229
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 229
230
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 230
231
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 231
232
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 232
233
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 233
234
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 234
235
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 235
236
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 236
237
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 237
238
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 238
239
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 239
240
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 240
241
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 241
242
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 242
243
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 243
244
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 244
245
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 245
246
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 246
247
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 247
248
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 248
249
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER 249
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
81
D1265 | Owner's Manual | Appendix
User (Token) Worksheet (User 227 to 249) (101-249 = D9412GV3/D9412GV2 only)
User
###
Master ID ###-0
Site
Card Data
Sub-User ###-1
Site
Card Data
Sub-User ###-2
Site
Card Data
Sub-User ###-3
Site
Card Data
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
82
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
D1265 | Owner's Manual | Appendix
User (Passcode) Worksheet (Blank)
User
###
Passcode
User
Group
__ __ __ __ __ __
Area Authority
User Name
1
2
3
4
5
6
7
8
____
__
__
__
__
__
__
__
__
USER ___
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER ___
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER ___
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER ___
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER ___
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER ___
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER ___
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER ___
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER ___
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER ___
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER ___
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER ___
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER ___
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER ___
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER ___
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER ___
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER ___
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER ___
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER ___
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER ___
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER ___
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER ___
__ __ __ __ __ __
____
__
__
__
__
__
__
__
__
USER ___
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
83
D1265 | Owner's Manual | Appendix
User (Token) Worksheet (Blank)
Use
r
###
Master ID ###-0
Site
Card Data
Sub-User ###-1
Site
Card Data
Security System Limitations
Not even the most advanced security system can
guarantee protection against burglary, fire, or
environmental threats. All security systems are subject
to possible compromise or failure-to-warn for a variety
of reasons including, but not limited to, the following:
 If sirens or horns are placed outside the hearing
range of people in remote areas of the building or
in areas, which are frequently closed off, they do
not provide the intended protection.
 If intruders gain access through unprotected points
of entry, the system will not detect their entrance.
 If intruders have the technical means of bypassing,
jamming, or disconnecting all or part of the
system, they are not detected.
 If the AC power supply is OFF and the back-up
battery is either missing or dead, sensors will not
detect intrusion.
84
Sub-User ###-2
Site
Card Data
Sub-User ###-3
Site
Card Data

Smoke detectors cannot detect smoke in chimneys,
walls, or roofs, or smoke blocked by a closed door.
They might not detect smoke or fire on a level of
the building different from the one on which they
are located. Smoke detectors might not be able to
warn in time about fires started by explosions,
improper storage of flammables, overloaded
electrical circuits, or other types of hazardous
conditions.
 If phone lines are from service, reports from the
security system to the Security Company cannot
be sent unless there is an alternate means of
communication. Telephone lines are vulnerable to
compromise by several means.
Inadequate maintenance and failure to test are the
most common causes of alarm failure. It is strongly
recommended that you test your system once a week
to be sure that all system components are working
properly.
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
D1265 | Owner's Manual | Appendix
Although having a security system might make you
eligible for reduced insurance premiums, the
system is no substitute for insurance. Warning
devices cannot compensate you for loss of life or
property.
Figure 3: Smoke Detector Locations (Elevation
View)
2
Fire Safety and Evacuation
Residential fire is a leading cause of accidental death.
Most fire related deaths occur at night when occupants
suffocate in their sleep from smoke and toxic gases,
rather than from burns. To help reduce this risk, the
following program should be implemented:
1.
Minimize fire hazards. Smoking in bed, cleaning
with flammable liquids such as gasoline, leaving
children home alone, and using unsafe holiday
decorations are some of the common causes of
household fire.
2.
Install a fire alarm system. The primary purpose of
this system is to protect lives by giving the earliest
possible warning of danger.
3.
A smoke detector should be provided to protect
each sleeping area in a home (Figure 2 and
Figure 3).
4
5
1
6
2
1 - Smoke Detector
2 - Bedroom
4.
Practice an escape plan. Because there might be
very little time between detection of a fire and the
time it becomes deadly, it is important that every
member of the family understand how to quickly
evacuate according to the plan.
5.
Plan both primary and alternate escape routes.
Since stairwells and hallways might be blocked
during a fire, exiting through a bedroom window
must be a part of the escape plan. If the sleeping
area is above the ground floor, install a means of
safely descending outside the building if one will
not already exist.
6.
As a part of this plan, all family members should
arrange to meet at a location away from the house
(such as a neighbor’s house) so you know that
everyone is accounted for.
3
1
1
2
Figure 2: Smoke Detector Locations (Plan View)
2
1
3
Figure 4: Escape Route
3
2
1 - Smoke Detector
2 - TV Room
3 - Bedroom
4 - Dining Room
5 - Kitchen
6 - Living Room
5
4
3
3
7
3
6
1
12347.
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
Fire
Escape Routes
Bedroom
Kitchen
5 - Dining Room
6 - Living Room
7 - Smoke Detector
If it is determined that the alarm was accidentally
sounded, the bell should be silenced, the detectors
reset, and your security company notified
immediately that there is no emergency situation.
85
D1265 | Owner's Manual | Appendix
Standard Displays
Your keypad uses standard and custom displays to
show the status of the security system. Many standard
displays are described below. Your system might not
use all of them. Descriptions of your custom text
follow.
*System Command*
Shows when you press the CMD button. The system is
waiting for you to enter a one or two digit number to
complete the command.
**No Authority**
The system will not recognize the passcode entered.
Perimeter On Delayed
Entry Delay/Enter Passcode to Disarm
When the system is turned on, entering through a
delay door starts entry delay time.
The keypad emits a tweedle tone and alternates
between Enter Passcode and press the ENTER
button to disarm and AREA # AREA TEXT is in
entry delay.
Indicates that the perimeter is armed (turned on) with
entry/exit delay time and shows Perimeter On
Delayed. (Refer to Perimeter Delay (CMD + 3) on page
22).
Perimeter Instant
Indicates that the perimeter is armed (turned on)
without entry/exit delay time and shows Perimeter
On Instant. (Refer to Turn On the Perimeter With No
Delays on page 21.).
You must turn off the system before entry delay time
expires to avoid creating an alarm event.
Exit Now
Area must be disarmed first
Arming your system starts exit delay time. The keypad
emits a repeating beep tone and shows Exit Now!.
Indicates that the function requested can only be
performed when the area is disarmed. Disarm the area
to perform the function.
86
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
D1265 | Owner's Manual | Appendix
System Trouble Displays
Serv Battery Missing
If you refer to any of the system trouble displays
shown below, contact your security company to
determine whether repairs are needed.
Indicates the security system’s battery is
disconnected or shorted.
The Silence button is only shown if a
trouble tone is present. Press the Silence
button to silence the following trouble
conditions.
Call for Service
Call your security company. Your security system
might have failed (Your Alarm Company is
replaced with the name of your security company).
Service Communication Fail
Your security system makes repeated attempts to
communicate with the security company.
In the event your security system fails to
communicate, the keypad buzzes and shows
Comm Fail Route Grp1 (Route Group number can
be from 1 to 4).
Service Battery Low
Indicates the security system’s battery is low, or
temporarily draining faster than the system can
charge it. If this display remains or appears
frequently, call your security company for service.
Notify your security company of the communication
trouble.
Service Keypad
Indicates that a keypad, other than the one
displaying the message, is in a trouble condition.
Notify your security company.
Service AC Failure
Indicates that AC power to the security system is
interrupted. Check the plug-in transformer and
circuit breaker. Entering CMD 4 silences the
trouble buzz. The display clears when AC power
returns.
Service Phone Line #1 (or #2)
Indicates telephone line trouble. Call your phone
company from another phone to report telephone
trouble. This message might not appear in some
systems.
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
87
D1265 | Owner's Manual | Appendix
Service Printer
24 Hour Point Bypass
Printer number could also be 18 or 19
Indicates that a local printer (if installed) at your
premises is in a trouble condition. Check to be sure
the printer is powered on, the paper is correctly is
inserted, and the printer is selected. Contact your
security company if you have questions or the
display doesn’t clear. You system might not include
a local printer.
This display indicates that 24-hour points have been
bypassed.
Service D9210
Indicates that one of the D9210 Access Control
Modules (possible of 8 total) connected to the
control panel has encountered a problem. Contact
your security company.
Service Zonex Bus 1 (or 2)
Shows when a problem has occurred with the
control panel’s Point Bus Wiring. Call your security
company.
Fire Point Bypass
This display indicates that fire points have been
bypassed.
88
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
D1265 | Owner's Manual | Appendix
Security System Glossary
Area
A group of detection devices
connected to your security system.
Arm
To turn on your controlled points
(burglar detection devices). When an
area is armed and a controlled point
trips, an alarm occurs or entry delay
begins. When an area is disarmed,
faulting controlled points will not
generate alarms.
Authority
Level
Your security company or security
representative assigns an authority
level to your passcode. The authority
level determines what keypad
functions you can execute.
Bypass
Selectively remove points from the
security system. You might bypass a
point in order to arm the perimeter
with a window open.
Central
Station
A facility where trained personnel
monitor your security system 24 hours
a day. Your security system might be
programmed to contact the central
station during alarm conditions,
enabling central station personnel to
dispatch the proper authorities.
Closing
Report
A report your system can be
programmed to send to the central
station indicating that an area has been
armed. Opening and closing reports
are commonly used by commercial
accounts.
Function
List
A list of functions programmed by
your security company. They can
perform most keypad functions with
only two or three button presses.
Entry
Delay
A programmed delay of system alarm
response, which allows you to enter an
armed area through the correct point
and disarm the area. If you don’t
disarm before the delay time expires,
the system begins an alarm response,
which might include reports to the
central station.
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
Exit Delay
A programmed delay of system alarm
response, which allows you to exit
after arming an area. If you don’t exit
before the delay time expires, entry
delay begins. You must disarm the
system. If you don’t disarm before
the delay time expires, the system
begins an alarm response, which might
include reports to the central station.
Faulted
Point
A point that is not normal (a door or
window is open).
Force Arm
To turn on (arm) the security system
even though one or more points are
faulted. Force arming bypasses the
faulted points.
Idle Text
The security system shows idle text at
keypads when it is not performing a
user-requested function. Idle text
shows the arming status of the system.
Master
Arm
To turn on (arm) both interior points
and perimeter points.
Menu
A list of functions you execute from a
keypad.
Opening
Report
A report your system can be
programmed to send to the central
station indicating that an area has been
disarmed. Opening and closing reports
are commonly used by commercial
accounts.
Perimeter
Arm
An arming command that arms only
the perimeter points.
Point
A detection device or group of devices
connected to your security system.
Points display individually at the
keypad with custom text. The text can
describe a single door, motion sensor,
smoke detector, or an area such as
UPSTAIRS or GARAGE.
Relay
Your system might have relays
programmed to provide control of
devices such as premises lighting or
entry gates. Your security company
programs relays for automatic control
and/or control from your keypad.
Trouble
A service condition that needs to be
corrected, such as a broken wire
89
D1265 | Owner's Manual | Appendix
Maintenance and Service
This security system requires very little maintenance,
however, you should test the system weekly to ensure
it is working properly. A test schedule and
maintenance program can be arranged. If you notice a
change in operation during normal use or testing, call
for service as soon as possible. Do not attempt to
repair the control panel, keypads, or detectors yourself.
How to Clean the Keypad
If your keypad gets dirty, apply a household glass
cleaner to a clean cloth or paper towel and wipe the
surface. Do not spray any liquid directly onto the
keypad. It could run inside the case and damage
electrical circuits.
Your Alarm Company
Name:
Call This
Number
Before
Testing
90
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
D1265 | Owner's Manual | Notes
Notes
Bosch Security Systems, Inc. | 9/10 | F01U169130-02
91
Bosch Security Systems, Inc.
130 Perinton Parkway
Fairport, NY, 14450
USA
www.boschsecurity.com
© Bosch Security Systems, Inc., 2010
Download PDF

advertising