User guide | Bosch Appliances GVS1000 Security Camera User Manual

Global View Station 1000
GVS1000
en
Operations Manual
Global View Station 1000
Table of Contents | en
3
Table of Contents
1
Safety
5
1.1
Important safety instructions
5
1.2
Safety precautions
7
1.3
Important notices
1.4
Customer Support and Service
11
2
Standard Operations
12
2.1
Pan/Tilt
12
2.2
Zoom and Focus Control
12
2.3
Presets
12
2.4
Soft Limits
13
2.5
Preset Tours
13
2.6
Auxiliary Functions
14
3
Code Translator Unit
17
3.1
Pelco Support
17
3.2
Biphase Support
18
4
Camera Default Configuration
19
5
Troubleshooting
22
5.1
General
22
5.2
Troubleshooting with Diagnostic Mode
23
6
Test Software
24
6.1
PTCR-20 Software Operation
24
6.1.1
Default Parameters
26
6.1.2
Using PTCR-20 to Set Soft Limits and Camera Control
26
6.1.3
Inverting Tilt Controls
28
6.1.4
Other Menus
28
6.2
Auxiliary Control Board
29
6.2.1
Reset Button
30
6.2.2
Address Selection
30
6.2.3
Protocol Selection
30
6.2.4
System Communication
30
6.2.5
Self Test Diagnostic Function
30
6.2.6
Termination Jumpers
30
6.2.7
Photocell Control Adjustments
30
6.3
Auxiliary Controls
31
6.3.1
Aux 1 2x Doubler Function
31
6.3.2
Aux 2 Wiper Function
31
6.3.3
Aux 3 Illuminator Control
31
6.3.4
Aux 4 Iris Control
31
6.3.5
Aux 5 Lens IR Correction Mode
31
6.3.6
Aux 6 Camera Color/Mono Mode
31
Bosch Security Systems, Inc.
7
Operations Manual
F.01U.173.867 | 2.0 | 2010.11
4
en | Table of Contents
Global View Station 1000
6.3.7
Aux 7 ZX700 IR On/Off Control
31
6.3.8
Aux 8 SLED IR On/Off Control
31
6.4
Voltage Touch Points
32
6.4.1
T3 SLED Power Input Indicator
32
6.4.2
T4 Auxiliary Control Power Indicator
32
6.4.3
T5 ZX700 Illuminator Output
32
6.4.4
T6 SLED #1 Power Output Indicator
32
6.4.5
T7 SLED #2 Power Output Indicator
32
6.5
Camera Control Board
33
6.5.1
Reset Button
34
6.5.2
System Communication
34
6.5.3
Camera Control Power Indicator
34
6.5.4
Address Selection
34
6.5.5
Protocol Selection
34
6.5.6
Termination Jumpers
34
6.6
Auxiliary Controls
35
6.6.1
Aux 1 2x Doubler Function
35
6.6.2
Aux 2 Wiper Function
35
6.6.3
Aux 3 Illuminator Control
35
6.6.4
Aux 4 Iris Control
35
6.6.5
Aux 5 Lens IR Correction Mode
35
6.6.6
Aux 6 Camera Color/Mono Mode
35
6.6.7
Aux 7 ZX700 IR On/Off Control
35
6.6.8
Aux 8 SLED IR On/Off Control
35
F.01U.173.867 | 2.0 | 2010.11
Operations Manual
Bosch Security Systems, Inc.
Global View Station 1000
Safety | en
1
Safety
1.1
Important safety instructions
5
DANGER!
The Lightening Flash with arrowhead symbol within an equilateral triangle indicates the
presence of uninsulated dangerous voltages within the product enclosure that may be
sufficient magnitude to constitute a risk of shock.
WARNING!
The exclamation point within an equilateral triangle alerts the user to the presence of
important operation and maintenance (servicing) instructions in the literature accompanying
the product.
CAUTION!
This grounding symbol indicates the safety ground of the unit.
WARNING!
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO
RAIN OR MOISTURE AND OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHOULD NOT BE
PLACED ON THIS APPARATUS.
TO COMPLETELY DISCONNECT THIS APPARATUS FROM THE AC MAINS, DISCONNECT THIS
POWER SUPPLY CORD PLUG FROM THE AC RECEPTACLE.
THE MAINS PLUG OF THE POWER SUPPLY CORD SHALL REMAIN READILY ACCESSIBLE.
A CLASS 1 APPARATUS SHALL BE CONNECTED TO A MAINS SOCKET OUTLET WITH A
PROTECTIVE EARTHING CONNECTION
Bosch Security Systems, Inc.
Operations Manual
F.01U.173.867 | 2.0 | 2010.11
6
en | Safety
Global View Station 1000
1.
Read these instructions.
2.
Keep this instruction.
3.
Heed all warnings.
4.
Follow all instructions.
5.
Do not use this apparatus near water.
6.
Clean only with dry cloth.
7.
Do not block any ventilation openings. Install in accordance with manufacturer
instructions.
8.
Do not install near any heat sources such as radiators, heat registers, stoves or other
apparatus (including amplifiers) that produce heat.
9.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized
plug has two blades with one wider than the other. A grounding type plug has two blades
and a third grounding prong. The wide blade or the third prong is provided for your
safety. If the provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the power where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or
sold with the apparatus. When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in a way, such as power-supply cord or plug is damaged,
liquid has been spilled or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has been dropped.
F.01U.173.867 | 2.0 | 2010.11
Operations Manual
Bosch Security Systems, Inc.
Global View Station 1000
Safety | en
1.2
Safety precautions
1.3
Important notices
7
Accessories - Do not place this unit on an unstable stand, tripod, bracket, or mount. The unit
may fall, causing serious injury and/or serious damage to the unit. Use only with the cart,
stand, tripod, bracket, or table specified by the manufacturer. When a cart is used, use
caution and care when moving the cart/apparatus combination to avoid injury from tip-over.
Quick stops, excessive force, or uneven surfaces may cause the cart/unit combination to
overturn. Mount the unit per the manufacturer's instructions.
All-pole power switch - Incorporate an all-pole power switch, with a contact separation of at
least 3 mm in each pole, into the electrical installation of the building. If it is needed to open
the housing for servicing and/or other activities, use this all-pole switch as the main
disconnect device for switching off the voltage to the unit.
Camera grounding - For mounting the camera in potentially damp environments, ensure to
ground the system using the ground connection of the power supply connector (see section:
Connecting external power supply).
Camera lens - An assembled camera lens in the outdoor housing must comply and be tested
in accordance with UL/IEC60950. Any output or signal lines from the camera must be SELV or
Limited Power Source. For safety reasons the environmental specification of the camera lens
assembly must be within the environmental specification of -10 °C (14 °F) to 50 °C (122 °F).
Camera signal - Protect the cable with a primary protector if the camera signal is beyond 140
feet, in accordance with NEC800 (CEC Section 60).
Coax grounding:
–
–
Ground the cable system if connecting an outside cable system to the unit.
Connect outdoor equipment to the unit's inputs only after this unit has had its grounding
plug connected to a grounded outlet or its ground terminal is properly connected to a
ground source.
–
Disconnect the unit's input connectors from outdoor equipment before disconnecting
the grounding plug or grounding terminal.
–
Follow proper safety precautions such as grounding for any outdoor device connected to
this unit.
U.S.A. models only - Section 810 of the National Electrical Code, ANSI/NFPA No.70, provides
information regarding proper grounding of the mount and supporting structure, grounding of
the coax to a discharge unit, size of grounding conductors, location of discharge unit,
connection to grounding electrodes, and requirements for the grounding electrode.
Disposal - Your Bosch product was developed and manufactured with high-quality material
and components that can be recycled and reused. This symbol means that electronic and
electrical appliances, which have reached the end of their working life, must be collected and
disposed of separately from household waste material. Separate collecting systems are
usually in place for disused electronic and electrical products. Please dispose of these units
at an environmentally compatible recycling facility, per European Directive 2002/96/EC.
Electronic Surveillance - This device is intended for use in public areas only. U.S. federal law
strictly prohibits surreptitious recording of oral communications.
Environmental statement - Bosch has a strong commitment towards the environment. This
unit has been designed to respect the environment as much as possible.
Bosch Security Systems, Inc.
Operations Manual
F.01U.173.867 | 2.0 | 2010.11
8
en | Safety
Global View Station 1000
Electrostatic-sensitive device - Use proper CMOS/MOS-FET handling precautions to avoid
electrostatic discharge.
NOTE: Wear required grounded wrist straps and observe proper ESD safety precautions when
handling the electrostatic-sensitive printed circuit boards.
Fuse rating - For security protection of the device, the branch circuit protection must be
secured with a maximum fuse rating of 16A. This must be in accordance with NEC800 (CEC
Section 60).
Grounding and polarization - This unit may be equipped with a polarized alternating current
line plug (a plug with one blade wider than the other blade). This safety feature allows the
plug to fit into the power outlet in only one way. If unable to insert the plug fully into the
outlet, contact a locally certified electrician to replace the obsolete outlet. Do not defeat the
safety purpose of the polarized plug.
Alternately, this unit may be equipped with a 3-pole grounding plug (a plug with a third pin for
earth grounding). This safety feature allows the plug to fit into a grounded power outlet only.
If unable to insert the plug into the outlet, contact a locally certified electrician to replace the
obsolete outlet. Do not defeat the safety purpose of the grounding plug.
Moving - Disconnect the power before moving the unit. Move the unit with care. Excessive
force or shock may damage the unit and the hard disk drives.
Outdoor signals - The installation for outdoor signals, especially regarding clearance from
power and lightning conductors and transient protection, must be in accordance with NEC725
and NEC800 (CEC Rule 16-224 and CEC Section 60).
Permanently connected equipment - Incorporate a readily accessible disconnect device in
the building installation wiring.
Pluggable equipment - Install the socket outlet near the equipment so it is easily accessible.
Power resupply - If the unit is forced to power down due to exceeding the specified operating
temperatures, disconnect the power cord, wait for at least 30 seconds, and then reconnect
the power cord.
Power lines - Do not locate the camera near overhead power lines, power circuits, or
electrical lights, nor where it may contact such power lines, circuits, or lights.
Rack-mount
–
Ventilation - Do not place this unit in a built-in installation or rack without proper
ventilation or adhering to the manufacturer's instructions. The equipment must not
exceed its maximum operating temperature requirements.
–
Mechanical loading - Properly mount the equipment in a rack to prevent a hazardous
condition due to uneven mechanical loading.
SELV
All the input/output ports are Safety Extra Low Voltage (SELV) circuits. SELV circuits should
only be connected to other SELV circuits.
Because the ISDN circuits are treated like telephone-network voltage, avoid connecting the
SELV circuit to the Telephone Network Voltage (TNV) circuits.
The system ground is only used to comply with safety standards or installation practices in
certain countries. Bosch does not recommend connecting system ground to safety ground
unless it is explicitly required. However, if the system ground and safety ground are
connected and grounding loops are causing interference in the video signal, use an isolation
transformer (available separately from Bosch).
CAUTION!
Connecting System ground to Safety ground may result in ground loops that can disrupt the
CCTV system.
F.01U.173.867 | 2.0 | 2010.11
Operations Manual
Bosch Security Systems, Inc.
Global View Station 1000
Safety | en
9
Video loss - Video loss is inherent to digital video recording; therefore, Bosch Security
Systems cannot be held liable for any damage that results from missing video information. To
minimize the risk of lost digital information, Bosch Security Systems recommends multiple,
redundant recording systems, and a procedure to back up all analog and digital information.
FCC & ICES Information
(U.S.A. and Canadian Models Only)
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
–
reorient or relocate the receiving antenna;
–
increase the separation between the equipment and receiver;
–
connect the equipment into an outlet on a circuit different from that to which the
–
consult the dealer or an experienced radio/TV technician for help.
receiver is connected;
Intentional or unintentional modifications, not expressly approved by the party responsible
for compliance, shall not be made. Any such modifications could void the user's authority to
operate the equipment. If necessary, the user should consult the dealer or an experienced
radio/television technician for corrective action.
The user may find the following booklet, prepared by the Federal Communications
Commission, helpful: How to Identify and Resolve Radio-TV Interference Problems. This booklet
is available from the U.S. Government Printing Office, Washington, DC 20402, Stock No. 004000-00345-4.
INFORMATIONS FCC ET ICES
(modèles utilisés aux États-Unis et au Canada uniquement)
Suite à différents tests, cet appareil s'est révélé conforme aux exigences imposées aux
appareils numériques de classe B, en vertu de la section 15 du règlement de la Commission
fédérale des communications des États-Unis (FCC), et en vertu de la norme ICES-003 d'Industrie
Canada. Ces exigences visent à fournir une protection raisonnable contre les interférences
nuisibles lorsque l'appareil est utilisé dans le cadre d'une installation résidentielle. Cet
appareil génère, utilise et émet de l'énergie de radiofréquences et peut, en cas d'installation
ou d'utilisation non conforme aux instructions, engendrer des interférences nuisibles au
niveau des radiocommunications. Toutefois, rien ne garantit l'absence d'interférences dans
une installation particulière. Il est possible de déterminer la production d'interférences en
mettant l'appareil successivement hors et sous tension, tout en contrôlant la réception radio
ou télévision. L'utilisateur peut parvenir à éliminer les interférences éventuelles en prenant
une ou plusieurs des mesures suivantes:
–
Modifier l'orientation ou l'emplacement de l'antenne réceptrice;
–
Éloigner l'appareil du récepteur;
–
Brancher l'appareil sur une prise située sur un circuit différent de celui du récepteur;
–
Consulter le revendeur ou un technicien qualifié en radio/télévision pour obtenir de
l'aide.
Bosch Security Systems, Inc.
Operations Manual
F.01U.173.867 | 2.0 | 2010.11
10
en | Safety
Global View Station 1000
Toute modification apportée au produit, non expressément approuvée par la partie
responsable de l'appareil, est strictement interdite. Une telle modification est susceptible
d'entraîner la révocation du droit d'utilisation de l'appareil.
La brochure suivante, publiée par la Commission fédérale des communications (FCC), peut
s'avérer utile : How to Identify and Resolve Radio-TV Interference Problems (Comment identifier
et résoudre les problèmes d’interférences de radio et de télévision). Cette brochure est
disponible auprès du U.S. Government Printing Office, Washington, DC 20402, États-Unis,
sous la référence n° 004-000-00345-4.
Copyright
This manual is the intellectual property of Bosch Security Systems and is protected by
copyright.
All rights reserved.
Trademarks
All hardware and software product names used in this document are likely to be registered
trademarks and must be treated accordingly.
NOTE!
This manual has been compiled with great care and the information it contains has been
thoroughly verified. The text was complete and correct at the time of printing. The ongoing
development of the products may mean that the content of the user guide can change without
notice. Bosch Security Systems accepts no liability for damage resulting directly or indirectly
from faults, incompleteness or discrepancies between the user guide and the product
described.
More information
For additional information, please contact the Bosch Security Systems location nearest you or
visit our web site at www.boschsecurity.com
F.01U.173.867 | 2.0 | 2010.11
Operations Manual
Bosch Security Systems, Inc.
Global View Station 1000
1.4
Safety | en
11
Customer Support and Service
If this unit needs service, contact the nearest Bosch Security Systems Service Center for
authorization to return and shipping instructions.
Service Centers
USA
Repair CenterTelephone: 800-566-2283
Fax: 800-366-1329
E-mail: repair@us.bosch.com
Customer Service
Telephone: 888-289-0096
Fax: 585-223-9180
E-mail: security.sales@us.bosch.com
Technical Support
Telephone: 800-326-1450
Fax: 585-223-3508 or 717-735-6560
E-mail: technical.support@us.bosch.com
Canada
Telephone: 514-738-2434
Fax: 514-738-8480
Europe, Middle East, Africa Region
Repair Center
Telephone: 31 (0) 76-5721500
Fax: 31 (0) 76-5721413
E-mail: RMADesk.STService@nl.bosch.com
Asia Region
Repair Center
Telephone: 65 63522776
Fax: 65 63521776
E-mail: rmahelpdesk@sg.bosch.com
Customer Service
Telephone: 86 (0) 756 7633117 or
86 (0) 756 7633121
Fax: 86 (0) 756 7631710
E-mail: customer.service@cn.bosch.com
Warranty and more information
For additional information and warranty queries, please contact your Bosch Security Systems
representative or visit our website at www.boschsecurity.com.
Bosch Security Systems, Inc.
Operations Manual
F.01U.173.867 | 2.0 | 2010.11
12
en | Standard Operations
Global View Station 1000
2
Standard Operations
2.1
Pan/Tilt
Standard pan and tilt operations are available - left, right, up, and down. The system is
capable of variable speeds, and features hard and soft limits for pan and tilt movement. When
using controllers with a joystick input, speed of movement can be increased by moving the
joystick further from the center position. The pan and tilt controls are not proportional to the
zoom.
2.2
Zoom and Focus Control
Standard zoom and focus control operations are available. If using a controller type with
joystick, twisting the joystick clockwise (CW) and counter-clockwise (CCW) will zoom in and
zoom out the system respectively. For focusing, the standard focus far and focus near
commands can be used. The focus control is not proportional to zoom.
Note: Unit is not auto-focus enabled, so manual focus adjustments will be required at times. It
is also important to ensure the lens is in the appropriate IR or visible mode, depending on the
type of light on scene. If an incorrect lens setting is being used, it may not be possible to
focus the lens. See the description of the Lens IR filter function, Aux 5.
2.3
Presets
Preset commands allow the system to automatically pan, tilt, zoom and focus to a pre-defined
position. Some preset commands are already pre-programmed into the system, and allow the
user to execute specialized functions.
Two types of commands are used with regards to presets – the “Program Preset” and “Call
Preset” commands. These two commands are different, and it is important to recognize the
difference between them.
Program Preset = Defines a preset
Call Preset = Run the defined preset
Refer to documentation specific to the controller for further instruction on performing the
above preset commands.
Note: Avoid setting preset positions with the lens at maximum or minimum wide or telephoto
focal lengths, or at maximum or minimum near or far focus settings of the lens. Doing so may
cause the system to malfunction and the unit may stall when the preset is called, either
manually or in a tour function.
F.01U.173.867 | 2.0 | 2010.11
Operations Manual
Bosch Security Systems, Inc.
Global View Station 1000
2.4
Standard Operations | en
13
Soft Limits
The soft limits are used to set programmed limits on the pan and tilt range. To adjust the soft
limits, perform the following steps:
–
Program preset 34. This function temporarily overrides all existing soft limits, allowing a
new soft limit to be set anywhere within the hard limits.
–
Move the unit to the desired left / right / up / down limit position.
–
Program presets 35 to 38 to set the new soft limits.
–
Preset 35: Right
–
Preset 36: Left
–
Preset 37: UP
–
Preset 38: Down
For example, to change the “left” soft limits, first program preset 34. Now the unit can be
moved to any “left” position within the “left” hard limits. Once the desired “left” position is
reached, program preset 36. The new “left” soft limit is now set.
Note: For each soft limit being set, all steps in the above procedure must be followed.
2.5
Preset Tours
Preset tours allow the system to automatically pan, tilt, zoom, and focus to preset positions
already defined in the system for a defined period of time. For the GVS1000, the system is
capable of storing up to three separate preset tours. To program a preset tour, perform the
following steps:
–
Program preset 81-83. By programming any of these three presets, it will initiate tour
programming and instruct the system that the following preset commands are to set a
preset tour. Depending on the preset selected, the system will store the commands to a
specific tour.
–
–
Program Preset 81: Start tour 1 programming
–
Program Preset 82: Start tour 2 programming
–
Program Preset 83: Start tour 3 programming
Define the tour – use the call preset command to enter preset positions already defined
in the system. Each positional “step” in the preset tour is defined by a pair of preset
commands. The first preset command will define the position for the tour to move to, and
the second preset will define the dwell time at the previous preset position (in seconds).
–
Program preset 87. This command ends tour programming, and instructs the system that
further commands are no longer associated with the tour functions. When the last preset
is reached during a tour, the system starts over again at the first preset.
–
Call preset 84-86. These preset positions are pre-programmed to call the preset tours.
Performing any manual commands to the system while a tour is being performed
overrides the tour and stops it from continuing.
–
–
Call Preset 84: Run tour 1
–
Call Preset 85: Runt tour 2
–
Call Preset 86: Run tour 3
For example, Tour 2 consists of the following sequence:
Preset 1, dwell time 4 seconds, followed by,
Preset 3, dwell time 3 seconds, followed by,
Preset 4, dwell time 5 seconds.
Bosch Security Systems, Inc.
Operations Manual
F.01U.173.867 | 2.0 | 2010.11
14
en | Standard Operations
–
Global View Station 1000
To program Tour 2 follow this command sequence:
–
Program Preset 82(Enter programming mode)
–
Call Preset 01 (Position 1 of the camera)
–
Call Preset 04 (Dwell time at the 1st position)
–
Call Preset 03 (Position 2 of the camera)
–
Call Preset 03 (Dwell time at the 2nd position)
–
Call Preset 04 (Position 3 of the camera)
–
Call Preset 05 (Dwell time at the 3rd position)
–
Program Preset 87(Exit programming mode)
–
Call Preset 85 (To start Tour 2 operation)
Note: An Auxiliary command that is sent during tour operation, once a tour has been initiated,
can cause the tour to be interrupted, causing the unit to maintain all current operations until
limits are reached. If this does occur, it is possible to manually override the operation by
performing a manual movement command (for example, a pan, tilt or zoom command, calling
a preset position, or calling a preset tour function).
For example, while performing a tour operation (consisting of panning clockwise, tilting
down, and zooming in simultaneously) an auxiliary command is used while these tour
operations are active these same commands will continue until the limits are reached.
Reaching the above limits would equate to: reaching the clockwise pan limit, reaching the
down tilt limit, and reaching maximum zoom setting.
2.6
Auxiliary Functions
Auxiliary functions are specialized functions of the system. Each of the auxiliary functions can
be called by using the auxiliary on/off command or by calling a pre-programmed preset.
Aux 1: Doubler On/Off
Aux1 ON or Call preset 51: doubler on
Aux1 OFF or Call preset 61: doubler off
Default: Doubler disengaged
Increases focal length by 2x. When engaging the doubler, the amount of light transmitted
through the lens is reduced. Therefore, it is generally best practice to use this function in the
day or when abundant ambient light is present at the viewing area.
Aux 2: Wiper On/Off
Aux2 ON or Call preset 52: wiper on
Aux2 OFF or Call preset 62: wiper off
Default: wiper off
When wiper is activated, it will remain on until the deactivate command is given.
F.01U.173.867 | 2.0 | 2010.11
Operations Manual
Bosch Security Systems, Inc.
Global View Station 1000
Standard Operations | en
15
Aux 3: Illuminator Control
Aux3 ON or Call preset 53: photocell control mode
Aux3 OFF or Call preset 54: manual control mode
Default: manual control mode
When in photocell control mode, the illuminators will be completely controlled by the
photocell, and manual override using Aux7 and Aux8 will not be possible.
The photocell sensitivity adjustment can also be adjusted via a pot in the Auxiliary board (VR1
– see “Auxiliary Control Board” section for further details). Adjusting VR1 CCW will decrease
the lux switch point level; adjusting VR1 CW will increase the lux switch point level. Setting
VR1 to either maximum limit will NOT force the system to stay in day or night mode.
Note: If Aux3 is disengaged when the IR is ON, the IR will remain on until it is manually turned
off.
Aux 4: Iris Control
Aux4 ON or Call preset 54: manual iris control mode
Aux4 OFF or Call preset 64: auto-iris control mode
Default: auto-iris control mode
When Aux4 is engaged, the lens iris can be manually controlled remotely with iris open / close
commands. Upon initialization, the iris will close and will require manual operation to open.
Aux 5: Lens IR Correction On/Off
Aux5 ON or Call preset 55: IR-corrected mode on
Aux5 OFF or Call preset 65: IR-corrected mode off
Default: IR-corrected mode off
The setting of the lens mode is crucial to ensure optimal performance of the GVS1000 system.
In day operation, the IR-corrected mode will not be needed. In dark environments where the
majority of light on scene is provided by the IR illuminators, the lens should be set to IRcorrected mode. However, if sufficient ambient light is preset on scene to replace the IR light,
IR-corrected mode should be disabled. An incorrect lens setting could cause the system to not
allow for proper focusing.
Aux 6: Camera Color/Mono Mode
Aux6 ON or Call preset 56: camera monochrome mode
Aux6 OFF or Call preset 66: camera color mode
Default: color mode
Use color mode for daytime applications or when sufficient light is available to produce
acceptable images. In low light scenarios, or when IR illumination is used, monochrome mode
should solely be used. Monochrome mode will allow for optimal light sensitivity.
Bosch Security Systems, Inc.
Operations Manual
F.01U.173.867 | 2.0 | 2010.11
16
en | Standard Operations
Global View Station 1000
Aux 7: ZX700 On/Off
Aux7 ON or Call preset 57: ZX700 illuminators on
Aux7 OFF or Call preset 67: ZX700 illuminators off
Default: ZX700 illuminators off
The ZX700 illuminators are narrow-beam, long range units useful for long range imaging when
insufficient levels of ambient light are on scene. Ensure the illuminators are properly aligned
for maximum performance.
Aux 8: SLED LED On/Off
Aux8 ON or Call preset 58: SLED illuminators on
Aux8 OFF or Call preset 68: SLED illuminators off
Default: SLED illuminators off
The SLED illuminators are wider angle short to medium range units using 3D diffuser and
Constant Light illumination technology. These illuminators are useful for ensuring consistent
illumination for short to medium range viewing.
F.01U.173.867 | 2.0 | 2010.11
Operations Manual
Bosch Security Systems, Inc.
Global View Station 1000
3
Code Translator Unit | en
17
Code Translator Unit
The code translator unit, with the auxiliary and camera control boards act as receivers for the
GVS1000 unit. During operation, LED indicators on the code translator unit can help to show
when data traffic is being received by the unit, as well as if there is a detected error in the
translator unit.
3.1
Pelco Support
The Pelco code translator box has four (4) status LEDs as shown below:
Figure 3.1
LEDs on the Pelco Code Translator
During normal operation the Rx light will flash whenever valid communication is received by
the code translator box. Communication specific to the motor will cause the Tx light to flash
as the unit sends commands to the motor. In Pelco D mode, the Rsp light flashes when data is
being received from the motor back to the translator unit. The Error light flashes when invalid
communication traffic is received, or if there is an error detected within the translator. If
power cycling does not turn the error LED off, contact a Bosch service center
Bosch Security Systems, Inc.
Operations Manual
F.01U.173.867 | 2.0 | 2010.11
18
3.2
en | Code Translator Unit
Global View Station 1000
Biphase Support
A unit with Biphase support is installed with two code translator units, as shown in Figure 3.2,
the Pelco P/D code translator and the Biphase translator unit (item 1, below). The Biphase
translator has four status LEDs, but only two are operational.
Figure 3.2
Location of Biphase code Translator inside GVS1000 Power Supply Unit
During normal operation, the Rx and Tx lights flash when valid communication with the
correct address is received by the code translator box.
Figure 3.3
F.01U.173.867 | 2.0 | 2010.11
LEDs on the Biphase Code Translator
Operations Manual
Bosch Security Systems, Inc.
Global View Station 1000
4
Camera Default Configuration | en
19
Camera Default Configuration
The camera is factory set for optimum performance. The following is for reference. For
complete information on the cameras settings, please refer to the camera manual.
The Mode Menu setting is accessed by pressing the center Menu/Select key for less than 1
second. The Installer Menu setting is accessed by pressing the Menu/Select key for at least 1
second.
Figure 4.1
OSD keypad location on camera
Figure 4.2
OSD keypad detail, showing back-focus lock
1
2
3
4
5
6
Bosch Security Systems, Inc.
Left Key
Up Key
Menu/Select Key
Right Key
Down Key
Lock
Operations Manual
F.01U.173.867 | 2.0 | 2010.11
20
en | Camera Default Configuration
Global View Station 1000
Mode 1
The table below shows the MODE 1 default camera settings for the camera.
Submenu
Function
Value
ALC
ALC Level
0
Peak/Average
0
ALC Speed
Medium
DVR/IP Encoder
On
Shutter
AES
Default Shutter
1/250
Gain Control
AGC
Maximum AGC
15
SensUp
2x
Day/Night
Day
Switch Level
0
Priority
Color
IR Contrast
Normal
Color Burst
On
XF-Dynamic
XF-DYN
Autoblack
On
Black Level
0
Sharpness
10
DNR
Auto
Peak White Invert
OFF
White Balance
ATW
Speed
Medium
Red Gain
0
Blue Gain
0
Green Gain
--
Saturation
5
Shutter/AGC
Day/Night
Enhance/Dynamic Engine
Color
F.01U.173.867 | 2.0 | 2010.11
Operations Manual
Bosch Security Systems, Inc.
Global View Station 1000
Camera Default Configuration | en
21
Installer Menu
The table below shows the Installer Menu default camera settings for the camera.
Submenu
Function
Value
Lens Wizard
Lens Type
Video
Alarm I/O
Alarm I/P
Low
Alarm Action
Mono
Bosch Security Systems, Inc.
Operations Manual
F.01U.173.867 | 2.0 | 2010.11
22
en | Troubleshooting
Global View Station 1000
5
Troubleshooting
5.1
General
Symptom
Possible Solution
No Pan/Tilt movement when
Check that the main power is on. Main power is on when the Power LED located
using a keyboard to control the
on the power supply case is on. If main power is off, then check the main power
unit
connection and the two fuses located in the power supply unit.
Check that the address on the controlling device matches the address of the
GVS1000.
If the Error LED on the code translator (in the power supply) is on, then the
protocol reaching the box is corrupt. Check the Tx/Rx lines for continuity. Check
that the GVS1000 controlling device is outputting valid protocol.
Check that the auxiliary control board is receiving valid protocol. The green LED
(LED 10) is blinking when valid communication is received by the auxiliary control
board.
Use the diagnostics mode on the auxiliary control board to test motor movement.
(refer to Section 5.2 Troubleshooting with Diagnostic Mode, page 23).
No Pan/Tilt movement when
Check that the green terminal blocks are disconnected from the code translator
using the PTCR20 software
(in the power supply unit).
Check the correct COM port and baud rate (9600bps) is selected in the software.
The COM port on the computer used to communicate with the GVS1000 is
computer dependent.
The Pan/Tilt motor drifts when
The Pan/Tilt motor drifts when the communication lines are incorrectly
trying to control the GVS1000
terminated. The termination for the auxiliary control board is set through jumper
JP6. The termination for the camera board is set through jumper JP3. Toggle the
termination on the camera control board first to solve the drifting problem. If the
problem persists, the auxiliary control board termination can be toggled as well
to solve the issue.
No image
Check that the main power is on. Main power is on when the Power LED located
on the power supply case is on. If main power is not on, then check the main
power connection and the two fuses located in the power supply unit.
Check that the video connection is contiguous.
Check that auxiliary 4 is off. When auxiliary 4 is turned on (manual iris control)
the iris will close completely (for protection purposes). When the iris is
completely closed, no image will appear on screen.
Fuzzy image
Verify that the housing front glass is clean. The GVS1000 is equipped with a wiper
(controlled through Aux 2).
The image may be out of focus. Focus the image using the controlling device.
The lens IR filter (Aux 5) setting could be used incorrectly. When the scene
consists of predominantly visible light, leave the lens IR filter off (auxiliary 5 off).
When the scene consists of predominantly IR light, turn on the lens IR filter (Aux 5
on).
Zoom/Focus stalls when using
Presets should not be set with maximum/minimum zoom or maximum near/far
presets
focus. Manual override with a controlling device will resume the GVS1000 to
normal operation.
F.01U.173.867 | 2.0 | 2010.11
Operations Manual
Bosch Security Systems, Inc.
Global View Station 1000
Troubleshooting | en
With the illuminators turned
The brightness of the IR illuminators cannot be observed when the scene is
on, no change in image
already illuminated with significant amounts of visible light.
brightness is observed
Check that the illuminators are on. When the illuminators turn on, there is a
23
visible red glow at the illuminators. The ZX700 illuminators have more of a red
glow when compared to the SLED illuminators. Do no look directly into the
illuminators to check for the red glow. The red glow can be observed by looking at
the illuminators from an angle.
Check that the illuminators are properly aligned. See the installation manual for
the IR illuminator alignment procedure.
Check that the lens IR filter is on (Aux 5 on) and that the camera is in night mode
(Aux 6 on). Both settings are required for IR sensitivity.
An auxiliary does not respond
When the auxiliaries do not respond to control input either the control boards are
to control input
not receiving communication or the auxiliary is malfunctioning. If the control
boards are not receiving communication, then:
–
Check that the address on the controlling device matches the address of the
GVS1000.
–
Check that the auxiliary control board is receiving valid protocol. The green
LED (LED 10) is blinking when valid communication is received by the
auxiliary control board.
If an auxiliary is malfunctioning, then turn on the board diagnostics mode (refer to
Section 5.2 Troubleshooting with Diagnostic Mode, page 23).
The system address or
When the system address or communication protocol is changed, it is
communication protocol does
recommended to power cycle the unit (or make the changes when power is off).
not take effect when changed
Instead of a power cycle, the reset switches can be pressed on the auxiliary and
camera control boards and, the green terminal blocks on the code translator can
be taken off and put back on again.
5.2
Troubleshooting with Diagnostic Mode
In the auxiliary control board, change DIP1, Switch 6 to ON. The GVS1000 diagnostics mode is
now active. The GVS1000 will cycle through all its auxiliaries and activating the appropriate
LEDs corresponding to the auxiliaries. Then, the diagnostics will cycle through motor
movements.
Observe the functionality of the GVS1000 during the self-test. The activation of auxiliaries
corresponds with the appropriate LED turning on (see Section 6.2 Auxiliary Control Board,
page 29 and Section 6.3 Auxiliary Controls, page 31). If the behavior of the auxiliary turning on
deviates from the descriptions in Sections 6.2 and 6.3 then contact a Bosch service center.
Bosch Security Systems, Inc.
Operations Manual
F.01U.173.867 | 2.0 | 2010.11
24
6
en | Test Software
Global View Station 1000
Test Software
A test program, PTCR-20, is provided for system maintenance. It is strongly advised that this
program is used only when necessary. The user can validate operation and set operational
parameters. If settings are changed incorrectly, this could cause the system to malfunction.
The PTCR-20 is compatible with all Windows 9x software, and Windows XP. It is NOT
compatible with Windows NT or Windows 2000. When using the PTCR-20 test software, the
GVS1000 can be operated directly from a bi-directional link compatible with RS422.
6.1
PTCR-20 Software Operation
Install the PTCR-20 Remote Emulator using the supplied CD.
Connect the GVS1000 to the PC using an RS232 straight cable. Unplug the green terminal
blocks from the code translator in the PSU. If the green terminal blocks are not removed from
the code translator when RS232 cable is attached, the software control may not function
properly.
Figure 6.1
1
2
F.01U.173.867 | 2.0 | 2010.11
Green Terminal Blocks
RS232 Straight Cable to PC
Operations Manual
Bosch Security Systems, Inc.
Global View Station 1000
Test Software | en
25
Using the PTCR-20 Software
1.
Run PTCR-20. The PC shows the display below.
2.
Verify COM port and Baud rate (9600 bps), and then click START. The COM port varies
Figure 6.2 PTCR-20 Main Screen
from computer to computer.
Figure 6.3 Verify COM Port and Baud Rate
The Handshake icon below indicates a communication link between the Pan/Tilt motor
and the PC has been established.
Figure 6.4 PTCR-20 Main Screen with Handshake
3.
After testing and setup, exit PTCR-20, disconnect the RS232 cable, and reconnect the
green terminal blocks in the PSU. Contact a Bosch service centre for further instructions
as needed.
Bosch Security Systems, Inc.
Operations Manual
F.01U.173.867 | 2.0 | 2010.11
26
en | Test Software
6.1.1
Global View Station 1000
Default Parameters
1.
Click the SETUP button. The default setup parameters are as shown below.
2.
Click the CAMERA button. The default parameters are as shown below.
Figure 6.5
Figure 6.6
6.1.2
Default Setup Settings
Default Camera Settings
Using PTCR-20 to Set Soft Limits and Camera Control
In the software, click the Jog/Limits button. Use the SL (soft limit) Override button as
needed. Use the track pad to the left of the Set Soft Limit controls to move the camera to the
appropriate soft limit position. The Set Soft Limit buttons correspond to the direction applied
on the track pad.
For example, click the “U” direction on the track pad until the camera has reached the desired
soft limit position. Then, click the Set Up Soft Limit to set the Up Soft Limit. Repeat for the
Clockwise, Counter Clockwise, and Down Soft Limits.
NOTICE!
Disengage the SL Override before exiting the software.
F.01U.173.867 | 2.0 | 2010.11
Operations Manual
Bosch Security Systems, Inc.
Global View Station 1000
Test Software | en
Figure 6.7
27
PTCR-20 Soft Limit Configuration
The colored circles on the right side of the software screen show a yellow or red color if a
positional soft limit or hard limit has been reached. During motor movement, the appropriate
circle will be green.
Figure 6.8
Positional Soft and Hard Limits
In the dial feedback, only the inner colored donut/circle is of interest. Red denotes an out of
bounds area (a limit) and green denotes a free moving area.
Figure 6.9
Bosch Security Systems, Inc.
Feedback Dials
Operations Manual
F.01U.173.867 | 2.0 | 2010.11
28
en | Test Software
6.1.3
Global View Station 1000
Inverting Tilt Controls
To invert the tilt settings, change the tilt settings:
–
Uncheck Tilt Mtr Reverse
–
Uncheck Tilt Res Invert
–
Click Set Normal/Reverse
–
Click Get Normal/Reverse to ensure the setting was applied
Figure 6.10
Settings to Invert Tilt Control
Once the Tilt controls are reversed, the up and down soft limits are also reversed.
For example, click the “U” direction on the track pad until the camera has reached the desired
Down soft limit position. Then, click the Set Up Soft Limit to set the Down Soft Limit. The
motor’s downward direction Soft Limit has now been set. Repeat for the Up Soft Limit.
The same goes for setting the soft limits on the keyboard. Position the camera unit to the
desired up view by pushing down on the joystick. Programming preset 38 will set Up Soft
Limit and programming preset 37 will set Down Soft Limit. The soft limit is independent of the
path taken to reach it, and only the position is saved for the appropriate limit.
6.1.4
Other Menus
The MOVE TO menu allows the user to input a coordinate for the GVS1000 to move to, the
PRESETS menu allows the user to manage the preset positions, the TOURS menu allows the
user to use to compose a tour from preset positions, and the OFFSETS menu allows the user
to set or reset the coordinate system for the GVS1000.
F.01U.173.867 | 2.0 | 2010.11
Operations Manual
Bosch Security Systems, Inc.
Global View Station 1000
6.2
Test Software | en
29
Auxiliary Control Board
Figure 6.11
Auxiliary Control Board
Component
SW1
JP6
JP7
T1
T2
T3
T4
T5
T6
T7
LED1
LED2
LED3
LED5
LED6
LED7
LED8
LED9
LED10
LED11
LED12
LED13
LED14
LED15
CN1
CN2
CN3
CN4
CN5
CN6
CN7
DIP1
Description
Board reset button
T1 telemetry jumper
T2 telemetry jumper
RS485/422 telemetry input to board
N/A
Aux8 SLED power input to SLED current control boards
24 VDC supply indicator
Aux 7 ZX700 power output from main PSU
Aux 8 SLED #1 power output from current control board #1
Aux 8 SLED #2 power output from current control board #2
Aux 1 Doubler status indicator
Aux 2 Wiper status indicator
Aux 3 photocell control indicator
Aux 5 IR mode indicator
Aux 6 camera NIGHT mode indicator
Aux 7 ZX700 telemetry on indicator (indicates telemetry status set to ON)
Aux 8 SLED telemetry on indicator (indicates telemetry status set to ON)
Auxiliary board power input indicator
RS485/422 data input indicator (constantly on in SELF-TEST mode). Flashing when receiving data
Power input to SLED current control boards
24 VDC system power indicator
Aux 7 ZX700 power on indicator (indicates actual power output to both ZX700 units)
Aux 8 SLED #1 power on indicator (indicates actual power output to SLED unit)
Aux 8 SLED #2 power on indicator (indicates actual power output to SLED unit)
NC
NC
Aux 7 relay connection to Main PSU
Aux 8 relay connection to current control boards #1 & #2
12 VDC input connection to VRB
NC
Photocell connection
Switches 1-4 for system address setting; switch 5 for Pelco P/D selection; switch 6 for diagnostics
VR1
function on/off control
Photocell sensitivity adjustment
Bosch Security Systems, Inc.
Operations Manual
F.01U.173.867 | 2.0 | 2010.11
30
en | Test Software
6.2.1
Global View Station 1000
Reset Button
–
SW1 – resets the board to default settings
–
Resetting should be used when changing the system address or communication protocol
when the unit is powered
6.2.2
Address Selection
–
DIP1 – Switches 1-4
–
Switches in various combinations of on/off will allow address setting of 1-16
–
Default address: 1
–
Address MUST be the same for Auxiliary Control board (in PSU), Camera Control board
(in camera assembly), and Code Translator (in PSU)
–
6.2.3
Protocol Selection
–
–
6.2.4
See the GVS1000 Installation Manual for further details
For Biphase models, ensure Pelco D mode is enabled.
DIP1 – Switch 5
–
Switch ON: Pelco D mode
–
Switch OFF: Pelco P mode
–
Default: Pelco D mode (switch off)
–
Switch UP position is ON
System Communication
–
–
–
T1 – Connects to system input
–
to receive system communication from controller
–
required for both simplex (2-wire configuration) and duplex (4-wire configuration)
T2 – connects to system output
–
to send system communication to controller – OPTIONAL
–
required only for duplex (4-wire configuration)
LED10 – indicates communication traffic to the system (LED always on when diagnostics
function engaged)
6.2.5
Self Test Diagnostic Function
–
DIP1 – Switch 6
–
Switch ON and jumper JP8 ON: diagnostics function on
–
Switch OFF and jumper JP8 OFF: diagnostics function off
–
Default: diagnostics function off (switch off, jumper JP8 OFF)
–
Tests Aux1 through 8 sequentially, and then tests motor Pan LEFT/RIGHT and Tilt UP/
–
3 seconds for each test function
–
Stops only at end of cycle
DOWN respectively
6.2.6
Termination Jumpers
–
–
6.2.7
JP6 / JP7 – controls the impedance communication lines
–
JP6 – T1 telemetry jumper
–
JP7 – T2 telemetry jumper – ALWAYS OPEN
JP8 – diagnostics tool jumper
Photocell Control Adjustments
–
CN7 – connection to photocell
–
VR1 – sensitivity adjustment for photocell switching
–
CCW rotation decreases lux switch point
–
CW rotation increases lux switch point
F.01U.173.867 | 2.0 | 2010.11
Operations Manual
Bosch Security Systems, Inc.
Global View Station 1000
Test Software | en
6.3
Auxiliary Controls
6.3.1
Aux 1 2x Doubler Function
–
–
6.3.2
–
–
–
–
–
LED2 ON = wiper on
–
LED2 OFF = wiper off
Default: OFF
LED3 – illuminator control indicator
–
LED3 ON = automatic photocell control on
–
LED3 OFF = manual control on (photocell off)
Default: MANUAL control mode (LED off)
No Aux4 indicator present on this board, only on Camera Control board
LED5 – IR correction mode indicator
–
LED5 ON = lens IR-correction enabled
–
LED5 OFF = lens IR-correction disabled
Default: IR-correction disabled
LED6 – camera mode indicator
–
LED6 ON = monochrome mode on
–
LED6 OFF = color mode on
Default: color mode
Aux 7 ZX700 IR On/Off Control
–
6.3.8
LED2 – wiper function indicator
Aux 6 Camera Color/Mono Mode
–
6.3.7
LED1 OFF = doubler off
Default: OFF
Aux 5 Lens IR Correction Mode
–
6.3.6
–
Aux 4 Iris Control
–
6.3.5
LED1 ON = doubler on
Aux 3 Illuminator Control
–
6.3.4
LED1 – doubler function indicator
–
Aux 2 Wiper Function
–
6.3.3
31
LED7 – ZX700 on/off indicator
–
LED7 ON = ZX700 on
–
LED7 OFF = ZX700 off
–
Default: ZX700 off
–
CN3 – relay connection to Meanwell PSU for control
Aux 8 SLED IR On/Off Control
–
–
LED8 – SLED on/off indicator
–
LED8 ON = SLED on
–
LED8 OFF = SLED off
Default: SLED off
–
LED11 – indicates power input to SLED control boards
–
Default: LED11 on (showing power available for SLED)
–
CN4 – relay connection to two SLED control boards
–
T3 – power input to current control board
Bosch Security Systems, Inc.
Operations Manual
F.01U.173.867 | 2.0 | 2010.11
32
en | Test Software
Global View Station 1000
6.4
Voltage Touch Points
6.4.1
T3 SLED Power Input Indicator
–
6.4.2
–
LED11 OFF = SLED controller power off
–
Voltage should read 18 VDC ± 0.5 VDC
T4 Auxiliary Control Power Indicator
LED12 – indicates system power
–
LED12 ON = auxiliary board power on
–
LED12 OFF = auxiliary board power off
–
Default: LED12 on (when system powered)
–
Voltage should read 24 VDC ± 0.7 VDC
T5 ZX700 Illuminator Output
LED13 – indicates power to both ZX700
–
LED13 ON = power output to ZX700 IR units on
–
LED13 OFF = power output to ZX700 IR units off
–
Default: LED13 off (power to ZX700 units off)
–
Voltage should read 27 VDC ± 0.7 VDC
T6 SLED #1 Power Output Indicator
–
6.4.5
LED11 ON = SLED controller power on
Default: LED11 on (when system powered)
–
6.4.4
–
–
–
6.4.3
LED11 – indicates SLED controller power (not actual on/off state of illuminators)
LED14 – indicates power to SLED #1
–
LED14 ON = power output to SLED #1 on
–
LED14 OFF = power output to SLED #1 off
–
Default: LED14 off (power to SLED #1 off)
–
Voltage should read 15 VDC ± 0.7 VDC
T7 SLED #2 Power Output Indicator
–
LED15 – indicates power to SLED #2
–
LED15 ON = power output to SLED #2 on
–
LED15 OFF = power output to SLED #2 off
–
Default: LED15 off (power to SLED #2 off)
–
Voltage should read 15 VDC ± 0.7 VDC
F.01U.173.867 | 2.0 | 2010.11
Operations Manual
Bosch Security Systems, Inc.
Global View Station 1000
6.5
Test Software | en
33
Camera Control Board
Figure 6.12
Camera Control Board
Component
SW1
T1
T2
T3
T4
T5
T6
LED1
LED2
LED3
LED4
LED5
Description
Board reset button
RS485/422 telemetry input to board
N/A
NC
NC
NC
NC
Aux 1 Doubler status indicator
Aux 2 Wiper status indicator
Aux 5 IR-correction mode indicator (used with LED7)
Aux 6 D/N mode indicator
RS485/422 data input indicator (constantly on in SELF-TEST). Flashing when
LED6
LED7
LED8
CN1
CN2
CN3
CN4
CN5
CN6
CN7
CN8
JP3
JP4
JP5
DIP1
receiving data
12 VDC input power indicator
Aux 5 IR-correction mode indicator (used with LED3)
Aux 4 iris control mode indicator
Aux 1 control connection to lens
Aux 4 control connection to lens
Aux 6 control relay to camera
12 VDC power input connection
Firmware programming connection
Aux 2 connection to wiper
Aux 2 24 V connection (for wiper park position)
Aux 5 control connection to lens
Protocol termination jumper (used with JP4)
Protocol termination jumper (used with JP3)
Protocol telemetry selection jumper (for PELCO D support only)
Switches 1-4 for system address setting; switch 5 for Pelco P/D selection; switch
DIP2
6 for diagnostics function on/off control
IR correction controls (positions 1 and 2 should be ALWAYS OFF - DEFAULT)
Bosch Security Systems, Inc.
Operations Manual
F.01U.173.867 | 2.0 | 2010.11
34
en | Test Software
6.5.1
Global View Station 1000
Reset Button
–
SW1 – resets the board to default settings
–
Resetting should be used when changing the system address or communication protocol
when the unit is powered.
6.5.2
System Communication
–
–
–
T1 – Connects to system input
–
to receive system communication from controller
–
required for both simplex (2-wire configuration) and duplex (4-wire configuration)
T2 – connects to system output
–
to send system communication to controller – OPTIONAL
–
required only for duplex (4-wire configuration)
LED5 – indicates communication traffic to the system (LED always on when diagnostics
function engaged).
6.5.3
Camera Control Power Indicator
–
6.5.4
LED6 – indicates presence of power
–
LED6 ON = camera control board power on
–
LED6 OFF = camera control board power off
–
Default: LED6 on (when system powered)
–
CN4 – connects to 12VDC for power input
Address Selection
–
DIP1 – Switches 1-4
–
Switches in various combinations of on/off will allow address setting of 1-16.
–
Default address: 1
–
Address MUST be the same for Auxiliary Control board (in PSU), Camera Control board
(in camera assembly), and Code Translator (in PSU).
–
6.5.5
Protocol Selection
–
6.5.6
Refer to the GSV1000 Installation Manual.
DIP1 – Switch 5
–
Switch ON: Pelco D mode
–
Switch OFF: Pelco P mode
–
Default: Pelco D mode (switch off)
–
Switch UP position is ON
Termination Jumpers
–
For Biphase models, ensure Pelco D mode is enabled.
–
JP3 / JP4 – controls the impedance of communication lines
–
JP3 – T1 telemetry jumper
–
JP4 – T2 telemetry jumper – ALWAYS CLOSED
–
JP5 – diagnostics tool jumper – ALWAYS OPEN
F.01U.173.867 | 2.0 | 2010.11
Operations Manual
Bosch Security Systems, Inc.
Global View Station 1000
Test Software | en
6.6
Auxiliary Controls
6.6.1
Aux 1 2x Doubler Function
–
6.6.2
Aux 2 Wiper Function
–
LED2 ON = wiper on
–
LED2 OFF = wiper off
Default: OFF
–
CN6 – connection to motor
–
CN7 – 24 VAC power in
Aux 3 Illuminator Control
No Aux3 indicator present on this board, only on Auxiliary Control board.
Aux 4 Iris Control
LED8 – iris control mode indicator
–
LED8 ON = manual iris control mode
–
LED8 OFF = auto-iris control mode
–
Default: auto-iris control mode
–
CN2 – connection to lens
–
Upon initialization, iris is fully closed
Aux 5 Lens IR Correction Mode
LED3 and LED7 – lens IR correction mode indicator
–
LED3 ON = lens IR correction enabled
–
LED3 OFF = lens IR correction disabled (visible light mode)
–
Default: LED3 and LED7 off
–
CN8 – connection to lens
Aux 6 Camera Color/Mono Mode
LED4 – camera mode indicator
–
LED4 ON = monochrome mode on
–
LED4 OFF = color mode on
–
Default: color mode
–
CN3 – connection to camera
Aux 7 ZX700 IR On/Off Control
–
6.6.8
LED2 – wiper function indicator
–
–
6.6.7
LED1 OFF = doubler off
CN1 – connection to lens
–
6.6.6
–
–
–
6.6.5
LED1 ON = doubler on
Default: OFF
–
6.6.4
LED1 – doubler function indicator
–
–
–
6.6.3
35
No Aux7 indicator present on this board, only on Auxiliary Control board.
Aux 8 SLED IR On/Off Control
–
Bosch Security Systems, Inc.
No Aux8 indicator present on this board, only on Auxiliary Control board.
Operations Manual
F.01U.173.867 | 2.0 | 2010.11
36
en | Test Software
F.01U.173.867 | 2.0 | 2010.11
Global View Station 1000
Operations Manual
Bosch Security Systems, Inc.
Bosch Security Systems, Inc.
www.boschsecurity.com
© Bosch Security Systems, Inc., 2010
Download PDF

advertising