Bosch Appliances LTC 0610 Digital Camera User Manual

Video | LTC 0610 Series DinionXF Color Cameras
LTC 0610 Series DinionXF Color Cameras
The LTC 0610 Series of High Performance 1/2-inch
Digital CCD Color Cameras create the best possible
image, even under the most difficult light and scene
conditions. Based on unique 15-bit digital video
processing technology and employing XF-Dynamic,
these cameras provide the ultimate sensitivity with
extended dynamic range. By employing the best 1/2inch CCD available, advanced front end processing,
combined with the outstanding Dinion DSP, the
cameras achieve an astonishing sensitivity, providing
better color images in low light situations and sharper
daytime images.
Intelligent White balance algorithms, supported by a
White Balance Hold function and even full manual
white balance, ensure the most accurate color
reproduction possible. All Dinion cameras are supplied
ready to operate. Simply attach and focus the lens,
and connect power to provide optimal pictures under
virtually all scene conditions. No tools are required for
back focus and power connection.
For extra challenging situations where fine tuning or
special settings are required, the camera parameters
can be individually set using the control buttons on the
side of the camera and On-screen Display (OSD). Also,
to aid installation, the camera automatically detects
the lens type, and using the Lens Wizard ensures
accurate (back) focusing for perfectly sharp pictures
at all times.
15-bit DSP technology
Bilinx communication
Default shutter
Extended dynamic range is brought to a new level on
the LTC 0610 Series Camera by XF-Dynamic
technology. XF-Dynamic automatically processes the
highly accurate 15-bit digital signal to optimally
capture the detail in both the highlight and lowlight
areas of the scene simultaneously, to maximize the
information visible in the picture.
Bilinx Technology
The LTC 0610 Series cameras incorporate Bilinx. Bilinx
is a bidirectional communication capability embedded
in the video signal of all Bosch Dinion cameras. With
Bilinx technicians can check status, change camera
settings and even update firmware from virtually
anywhere along the video cable. Bilinx reduces service
and installation time, provides for more accurate setup
and adjustment, and improves overall performance. In
addition, Bilinx uses the standard video cable to
transmit alarm and status messages, providing
superior performance without additional installation
Video Motion Detection
The built-in video motion detector allows you to select
up to four fully programmable areas with individual
thresholds. The global scene change detector
2 | LTC 0610 Series DinionXF Color Cameras
minimizes false alarms caused by sudden lighting
condition changes, such as switching on or off the
indoor or security lighting. When motion is detected
alarms may be displayed in the video signal, the output
relay can be closed in addition to alarm message
transmission on Bilinx.
Auto Black
The automatic black level feature, enhances contrast
by removing veiling glare from the picture or when
contrast is reduced by fog or mist.
Default Shutter
When viewing moving objects a fast shutter speed is
required. When using a fast shutter speed the lens
opening or gain control needs to be increased to
maintain the video signal. The camera sensitivity is
limited by the fast shutter speed. The default shutter
setting of the LTC 0610 offers the best of all worlds,
fast shutter speed as long as there is sufficient light,
however as the light level falls, when other
adjustments have been exhausted, the shutter reverts
to the standard setting maintaining the cameras
excellent sensitivity.
Certifications and approvals
Electro Magnetic Compatibility
EN55022 class B, FCC class B part 15
EN50130-4 Alarm Systems, Part 4
Camera with 500 gr (1.1 lbs) lens according to
LTC 0610/11 and LTC 0610/51: EN60065
LTC 0610/21 and LTC 0610/61: UL6500, cUL CAN/CSA E60065-00
Declaration of Conformity
Declaration of Conformity
Installation/configuration notes
Back Light Compensation (BLC)
Offering a fully programmable BLC area of interest,
and a variable BLC level, the camera can be easily set
up for even the most challenging entrance
Lens Wizard
The LTC 0610 Series automatically detects the type of
lens installed. The Lens Wizard will focus the lens at
the maximum lens opening, to ensure that focus is
maintained throughout the entire 24-hour day/night
cycle. No special tools or filters are required.
Programmable Modes
The camera supports three independent operating
modes. The 3 modes are preprogrammed for typical
applications, but are fully programmable for individual
situations. Switching between modes is easy via Bilinx
or the external alarm input.
The LTC 0610 cameras feature NightSense. With
NightSense the sensitivity is increased by 9 dB in
monochrome mode. NightSense can be automatically
activated in low light situations, or remotely using
By increasing the integration time on the CCD up to 10
times, the effective sensitivity is dramatically
enhanced, especially useful where there is no artificial
lighting and you rely on the moon, stars and scattered
Dimensions in mm (inches)
Parts included
LTC 0610 Series DinionXF Color Camera
Spare male 4–pin lens connector
Lens not included
Technical specifications
Model No.
LTC 0610/11
12–28 VAC
45–65 Hz
11–39 VDC
LTC 0610/21
12–28 VAC
11–39 VDC
45–65 Hz
3 | LTC 0610 Series DinionXF Color Cameras
LTC 0610/51
85–265 VAC
45–65 Hz
Alarm Input (TTL)
Profile switching, +5 V nominal, +40 VDC max.
LTC 0610/61
85–265 VAC
45–65 Hz
Alarm Output Relay
Max. 30 VAC or +40 VDC, max. 0.5 A
continuous, 10 VA
Power Consumption
Interline CCD type, ½-in. image format
External Synchronal
75 Ohm or High Impedance selectable
Up to 1000 m (3000 ft) coax without external
amplifiers (automatic setup in combination
with coaxial communication)
Camera ID
16 character editable string, position
Lens Types
Manual, DC- and Video-iris auto-detect with
override DC-iris drive: max 50mA continuous
Active Pixels
PAL Models
752 H x 582 V
NTSC Models
768 H x 492 V
Sensitivity (3200 k)
Sensitivity (full
1.4 lx (0.14 fc)
Sensitivity 50 IRE1)
0.35 lux / 0.14 lux (NightSense)
(0.035 fc / 0.014 fc (NightSense))
Video-iris: 11.5 ± 0.5 VDC, max. 50 mA
Remote Control
Bi-directional coaxial communication
1) F/1.2, 89% reflection, SensUp off
0.18 lux / 0.08 lux (NightSense)
(0.018 fc / 0.008 fc (NightSense))
Illumination with
0.018 lux / 0.008 lux (NightSense)
(0.0018 fc / 0.0008 fc (NightSense))
540 TVL
> 50dB
Video Output
1Vpp, 75 Ohm
Y/C Output
Y: 1 Vpp / C: 0.3 Vpp
Operating Temperature
-20 °C to +50 °C (-4 °F to +122 °F)
Internal, Line Lock, HV-lock and Genlock (Burst
lock) selectable
Storage Temperature
-25 °C to +70 °C (-13 °F to +158 °F)
Operating Humidity
20% to 93% Relative humidity
Auto (1/60 (1/50) to 1/500000), fixed,
flickerless, default
Storage Humidity
up to 98% Relative humidity
Night Sense
Auto, forced, off
Ordering information
Sensitivity up
Off, automatic continuous up to 10x
LTC 0610/11 DinionXF Color Camera
Auto Black
On, off selectable
Dynamic Range
32x dynamic range enhancement
1/2-inch, high performance, 540 TVL, PAL, DSP, 12 –
28 VAC/11 – 39 VDC, 50 Hz
Dynamic Noise
Auto, off selectable
LTC 0610/21 DinionXF Color Camera
Sharpness enhancement level selectable
1/2-inch, high performance, 540 TVL, NTSC, DSP, 12 –
28 VAC/11 – 39 VDC, 60 Hz
Off, area and level selectable
Auto (maximum level selectable to 28 dB) or
fixed level selectable
1/2-inch, high performance, 540 TVL, PAL, DSP, 85 –
265 VAC, 50 Hz
Lens Mount
C and CS
Order number LTC0610/51
White Balance
ATW (2500–10000 K), AWB hold, manual WB
4 area, sensitivity selectable
Alarm Output
VMD or Bilinx
(H x W x L)
59 x 67 x 122 mm (2.28 x 2.6 x 4.8 in.)
without lens
450 g (0.99 lbs) without lens
Tripod Mount
Bottom (isolated) and top 1/4-inch 20 UNC
OSD with softkey operation
Order number LTC0610/11
Order number LTC0610/21
LTC 0610/51 DinionXF Color Camera
LTC 0610/61 DinionXF Color Camera
1/2-inch, high performance, 540 TVL, NTSC, DSP, 85 –
265 VAC, 60 Hz
Order number LTC0610/61
4 | LTC 0610 Series DinionXF Color Cameras
LTC 3264/30 Varifocal Lens
1/2-inch, 4.5 – 10 mm, DC-iris, CS-mount F1.6-360, 4pin
Order number LTC3264/30
LTC 3283/20 Zoom Lens
1/2-inch, 8.0 – 48 mm, Video-iris, CS-mount F1.4-360,
Order number LTC3283/20
TC120PS Power Supply Unit
110-120 VAC/15 VDC, 50/60 Hz, 300 mA
Order number TC120PS
TC220PS Power Supply Unit
230 VAC/12 VDC, 50 Hz, 10 VA
Order number TC220PS
TC220PSX‑24 Power Supply Unit
230 VAC/20 VAC, 50 Hz, 20 VA
Order number TC220PSX-24
TC1334 Power Supply Unit
120 VAC/24 VAC, 60 Hz, 30 VA
Order number TC1334
LTC 3274/41 Varifocal Lens
1/2-inch, 7.5 – 75 mm, DC-iris, C-mount, F1.7-360, 4pin
Order number LTC3274/41
Software Options
VP‑CFGSFT Configuration Software
for cameras using Bilinx, includes VP-USB Adaptor
Order number VP-CFGSFT
Represented by:
Bosch Security Systems, Inc.
130 Perinton Parkway
Fairport, New York, 14450, USA
Phone: +1 800 289 0096
Fax: +1 585 223 9180
Europe, Middle East, Africa:
Bosch Security Systems B.V.
P.O. Box 80002
5617 BA Eindhoven, The Netherlands
Phone: + 31 40 2577 284
Fax: +31 40 2577 330
© Bosch Security Systems 2013 | Data subject to change without notice
2010020875 | en, V1, 29. Mar 2013
Robert Bosch (SEA) Pte Ltd, Security
11 Bishan Street 21
Singapore 573943
Phone: +65 6571 2808
Fax: +65 6571 2699
America Latina:
Bosch (Shanghai) Security Systems Ltd. Robert Bosch Ltda Security Systems Division
201 Building, No. 333 Fuquan Road
Via Anhanguera, Km 98
North IBP
CEP 13065-900
Changning District, Shanghai
Campinas, Sao Paulo, Brazil
200335 China
Phone: +55 19 2103 2860
Phone +86 21 22181111
Fax: +55 19 2103 2862
Fax: +86 21 22182398
Download PDF