Bosch Appliances MUM 7000 UC Blender User Manual

Owner’s Manual
Concept Series Kitchen Machines
for models:
MUM 7000 UC • MUM 7100 UC
MUM 7010 UC • MUM 7150 UC
MUM 7220 UC
READ THIS MANUAL
thoroughly for important safety and operating
instructions before using this appliance.
1
IMPORTANT SAFEGUARDS
WARNING: A risk of fire and electrical shock exists in all electrical appliances and may
cause personal injury or death.
When using electrical appliances, basic safety precautions should always be followed,
including the following:
1. Read all instructions before using the kitchen machine.
2. To protect against risk of electric shock, do not put the drive unit in or under water or
other liquid.
3. This appliance is not for use by children.
4. Close supervision is necessary when any appliance is used near children.
5. Do not leave appliances unattended during operation.
6. Unplug from outlet when not in use, before putting on or taking off parts, and
before cleaning.
7. To disconnect: Switch appliance off then remove plug from power supply.
8. Avoid contacting moving parts. Keep hands, hair, clothing, as well as spatulas
and other utensils away from whisks, beaters, blades, disc, dough hook and/or other
moving parts during operation to reduce the risk of injury to persons, and/or
damage to the appliance or its attachments.
9. Do not operate any appliance with a damaged cord or plug, or after the appliance
malfunctions or is dropped or damaged in any manner. Return appliance to the
nearest authorized service facility for examination, repair or electrical or mechanical
adjustment.
10. The use of attachments not recommended or sold by the appliance manufacturer
may cause fire, electric shock or injury and is therefore prohibited.
11. Do not use outdoors or when standing in a damp area.
12. Do not let cord hang over edge of table or counter, or touch hot surfaces.
13. Always operate appliance with covers in place.
14. Blades are sharp. Handle carefully due to risk of injury.
15. Remove beaters from mixing bowl before washing.
NOTE: ALSO BE SURE TO READ THE WARNINGS AND CAUTIONS THAT ARE
PROVIDED BEFORE EACH ATTACHMENT’S OPERATING INSTRUCTION.
SAVE THESE INSTRUCTIONS
2
TABLE OF CONTENTS
IMPORTANT SAFEGUARDS .................................................................. 2
Table of contents ..................................................................................... 3
ABOUT YOUR KITCHEN MACHINE ....................................................... 4
Bosch Concept Series Kitchen Machine ................................................. 4
Unpacking ............................................................................................... 4
Electrical specifications ............................................................................ 4
Before using for the first time .................................................................. 4
Getting to know your Bosch Kitchen Machine ......................................... 6
Special accessories ..................................................................... 6
Power unit features ................................................................................. 6
Getting started ..................................................................................... 7-9
STANDARD ATTACHMENTS .................................................................. 9
Mixing bowl w/twin beating whisks and dough hook ............................. 9
How to use dough hook ......................................................... 10-11
Placing into operation with dough hook ....................................... 11
How to use twin beating whisks .................................................. 11
Operation with dough hook and whisk assembly .......................... 12
Use of mixing bowl with twin beating whisks ............................... 13
Placing into operation with twin beating whisks .......................... 14
Care and cleaning of bowl and its accessories ........................... 14
Blender with unbreakable plastic jar ..................................................... 15
How to use blender ...................................................................... 15
Placing blender into operation ...................................................... 16
Example of use of blender ........................................................... 16
Care and cleaning of blender ........................................................ 17
Slicer/shredder with unbreakable bowl ................................................ 17
Slicer/shredder, intended use ...................................................... 18
Placing slicer/shredder into operation .......................................... 19
Care and cleaning of slicer/shredder ............................................ 20
Food processor with unbreakable bowl ................................................. 20
How to use food processor blade ................................................. 20
Placing into operation with food processor blade .......................... 22
Examples of use of food processor .............................................. 22
Care and cleaning of food processor blade and bowl .................... 23
How to use discs w/5-cup capacity bowl ..................................... 23
Placing into operation with discs and disc holder ......................... 24
Care and cleaning of discs, disc holder and bowl ......................... 24
SERVICE and REPAIR .......................................................................... 24
TROUBLESHOOTING ................................................................. 25
SAMPLE RECIPES .......................................................................... 26-27
SPECIAL ACCESSORIES ..................................................................... 30
BOSCH small appliance warranty ........................................................... 31
HOUSEHOLD USE ONLY
3
• The MUM 7150 UC
comprised of the electronic power unit
with integral cord storage, six-cup
capacity blender (MUZ7MX1), six-quart
capacity mixing bowl, bowl lid with
integral filling funnel and cover
(MUZ7KR1), twin beating whisks, dough
hook, five-cup capacity food processor
with safety locking lid (MUZ7MM2) and
motor drive cover.
ABOUT YOUR KITCHEN MACHINE
Congratulations on having selected one of
the Bosch Concept Series Kitchen
Machines. A series of kitchen machines that
we, and—thankfully—cooking professionals
the world over, feel are the best householdtype kitchen machines available.
As you read through these instructions,
please pay particular attention to the
IMPORTANT SAFEGUARDS. Specific
safeguards for the attachments as well as
warnings and cautions are provided in each
section describing the operation of that
particular attachment.
• The MUM 7220 UC
comprised of the electronic power unit
with integral cord storage, 12-cup
capacity slicer/shredder with three
stainless steel blades (MUZ7TS1), sixcup capacity blender (MUZ7MX1), sixquart capacity stainless steel mixing
bowl, bowl lid with integral filling tube
and cover (MUZ7ER1), twin beating
whisks, dough hook, safety cover and
bowl scraper.
Bosch Concept Series Kitchen Machine
The Bosch Concept Series Kitchen
Machine is available in 5 models:
• The MUM 7000 UC
comprised of the electronic power unit
with integral cord storage, six-quart
capacity mixing bowl, bowl lid with
integral filling tube and cover
(MUZ7KR1), twin beating whisks, dough
hook, motor drive cover and bowl
scraper.
Unpacking
Carefully remove the power unit from its
packaging and place it on the counter so it
is ready to use. As you remove the
accessories from the carton, check them
against Figure 1 to assure that all the
standard parts are present.
• The MUM 7010 UC
comprised of the electronic power unit
with integral cord storage, six-quart
capacity mixing bowl, bowl lid with
integral filling tube and cover
(MUZ7KR1), twin beating whisks,
professional-style dough hook, motor
drive cover and bowl scraper.
Electrical Specifications
Check to make sure that the voltage on
which your kitchen machine is to operate
is the same as specified on the rating plate.
Standard North American models have an
electrical power rating of 700-watt maximum
power rating with the accessory attachment
that draws the most power (some accessory
attachments may draw less power).
• The MUM 7100 UC
comprised of the electronic power unit
with integral cord storage, six-cup
capacity blender (MUZ7MX1), six-quart
capacity mixing bowl, bowl lid with
integral filling funnel and cover
(MUZ7KR1), twin beating whisks, dough
hook and motor drive cover.
Before Using for the First Time
Before using any of the attachments for the
first time it is recommended they be washed,
rinsed well and dried. Of the attachments
supplied, with the systems in this manual,
all parts, except the whisk holder for the
twin beating whisks and the blender’s
blade/base assembly, are dishwasher safe:
4
MUM 7220 UC
MUM 7010 UC
MUM 7100 UC
MUM 7150 UC
MUM 7000 UC
Figure 1
5
•
> The whisk holder should be hand
washed in warm soapy water, rinsed
and dried.
> The blender’s blade/base assembly
should be washed under running water
and dried.
Bosch Small Appliances
Customer Support
BSH Home Appliances
5551 McFadden Avenue
Huntington Beach, CA 92649
Note: It is recommended that the blender’s
blade/base assembly never be left to
stand in water or soap solution to prevent
the bearing lubricant from being washed out.
or call us at:
Getting to Know Your Bosch Kitchen
Machine
The Bosch Concept Series Kitchen
Machines are comprised of various
attachments, depending on the system
purchased (see above). In addition to the
attachments listed on the previous pages
that are available with the standard systems,
Bosch offers many special accessories.
Power Unit Features
All MUM 7000 power units have the following
features, refer to figure 2:
•
1 (866) 44BOSCH
[1 (866) 442-6724]
700-watt motor
The most powerful motor offered with any
household kitchen machine.
Electronic speed control
Six-position rotary switch is located at front
of power unit: 4 speeds plus a momentary
pulse function and a stop position “O/Off,”
see figure 2a.
Special Accessories
To allow you to get the most service from
your Bosch Concept Series Kitchen
Machine, Bosch engineers have designed
a line of special accessories to expand the
usefulness of your machine. In addition to
the attachments that come with the various
Concept Series Kitchen Machines, there
are optional accessories that can be ordered
separately. These accessories include a
food and meat grinder, grain mills, citrus
juicer and ice cream maker, plus additional
attachments that can be used with the meat
grinder: fancy cookie attachment, fruit
pulper, pasta-making disks and grater
attachment.
See
SPECIAL
ACCESSORIES, at the back of this
booklet, page 30. Or, to view all currently
available accessories, visit our Web site at
Control status indicator
Indicates when power unit is functioning
normally, or if there is a problem that has
caused the electronic safety control to be
activated, see figure 2b:
• The indicator will glow steadily when
the power unit is functioning normally.
or,
• The indicator will flash if the electronic
safety control of the power unit has
been activated.
Mono drive
Four electronically controlled shaft speeds
are all available from a single location; each
attachment automatically connects to the
appropriate drive speed.
www.boschsmallappliances.com
Work on expanding the usefulness of the
Bosch Kitchen Machine is a continuing
process. If there is some type of accessory
in which you are interested in that is not
included at the back of the book, please
either write us at:
Motor drive cover
Used to cover mono drive when not in use,
see figure 2c.
6
Gentle start
Getting Started
The operation of your Bosch Concept Series
Kitchen Machine is summarized below.
a special feature that brings the motor up
to speed over a two-second period; limiting
splashing.
Specific instructions for using each of the
attachments, provided with the kitchen
machine systems covered by this manual,
follow the summarized instructions. Please
read the specific instructions thoroughly
before using that attachment, paying
particular attention to the IMPORTANT
SAFEGUARDS and WARNINGS provided.
Convenient cord storage
Convenient cord storage is located on the
back of the power unit, see 2d.
Integrated hand grips
Side recesses provide for easy lifting and
carrying of power unit when not in use, see
2e.
1.
Four rubber feet
Four rubber feet with formed suction cups
provide the ultimate in stability, while also
serving to isolate the power unit from the
hard surface to minimize noise and
vibration. Need clean smooth surface, see
figure 2f.
Figure 2.
7
Place power unit on suitable work
surface.
Before using the machine with any of
the attachments the power unit should
be placed on suitable work surface.
The surface should be sturdy, smooth
and clean; make sure that there is
All models of the Bosch Concept
Series Kitchen Machines incorporate
an electronic safety control to protect
the motor. If the safety becomes
activated, the indicator will flash. See
TROUBLESHOOTING at the back of
this manual if status indicator is
flashing.
no flour or oil on the surface. A clean
smooth surface will provide the best
footing for the suction cup feet on
the power unit and will limit slipping
and/or “walking.”
2.
Plug power unit into power supply.
Unwind the power unit’s cord to
appropriate length and plug it into
a convenient nearby receptacle.
3.
Remove motor drive cover.
Remove motor drive cover from monodrive, see figure 2c.
4.
Select attachment to be used.
Select attachment you wish to use
and place on power unit. See specific
instructions for attachment selected.
Specific instructions are located on
pages listed below:
Attachment
Figure 3.
6.
Turn power unit off.
When your work with the attachment
is completed or the capacity of the
batch feed attachment has been
reached, turn the power unit to off
position, “O/Off” and unplug.
7.
Remove the attachment.
Remove the attachment from the
power unit, per instructions for the
specific attachment being used.
8.
Continue use.
If the attachment was of the batch feed
type and you wish to continue using
the attachment, empty the bowl or jar
of the attachment per its specific
instructions and reinstall the
attachment as before. Repeat the
steps 5 through 7 as often as
necessary to complete necessary
work.
9.
Work completed,
remove attachment.
If the attachment is of the continuous
feed type or is the batch type and you
have completed the work you wished
Pages
Mixing bowl w/dough hook ........ 9-11
Mixing bowl w/twin whisks ....... 11-14
Blender ..................................... 15-17
Slicer/shredder ......................... 17-20
Food processor ........................ 20-24
Table 1.
5.
Operate unit with rotary switch.
Once the attachment is in place, the
speed of its moving components can
be controlled through the use of the
rotary switch at the front of the power
unit. See figure 2a. The rotary switch
has six positions:
a. “M,” a momentary “pulse” position
that provides full speed and power
for the time it is held in position.
b. “O/Off,” the off position.
and
c. Four speeds labeled 1, 2, 3 and 4.
Speed 1 is the lowest speed. The
speed increases with each
succeeding step up to the highest
speed, speed 4.
8
to perform with the attachment,
remove the attachment from the power
unit per the instructions for the specific
attachment being used.
STANDARD ATTACHMENTS
Following are the specific instructions for
the standard attachments provided with the
Bosch Concept Series Kitchen Machines
covered by this manual.
10. Place contents (batch feed type)
If the attachment is the batch feed
type, disassemble per the specific
attachment’s instructions and place
the contents in a suitable container.
Mixing Bowl with Twin Beating Whisks
and Dough Hook
(MUZ 7 KR1 or MUZ 7 ER1)
WARNING
11. Care and Cleaning
Once you have completed working
with the Bosch Kitchen Machine, the
next step is to disassemble and clean
the attachments. If you wish to use
another attachment please return to
step 4, above.
1. There is a risk of injury from rotating
tools when using the mixing bowl with
the dough hook or the twin beating
whisks.
2. Avoid contact with moving parts. Keep
hands, hair, clothing, as well as
spatulas, bowl scrapers and other
utensils away from dough hook and
whisks during operation to prevent
injury, and/or damage to the power unit
or accessories.
3. Always work with the bowl lid fitted in
place.
4. Do not change tools until the power unit
has come to a complete stop; when
switched off, the power unit will continue
to turn for a brief period.
Power unit
With the power unit turned off and
unplugged, it should be cleaned only with
a clean, damp cloth. Never use coarse or
caustic cleaning products to clean the
power unit. Never immerse the power unit
in water. Then wipe off the motor drive cover
and reinstall on the power unit.
The power unit may be left on the counter
or stored for future use. In either case,
always be sure to replace the motor drive
cover on the mono drive. This will prevent
dust and/or flour build-up in the drive.
All models of the Bosch Concept Series
Kitchen Machines are provided with a sixquart mixing bowl with twin beating whisks
and dough hook. You may have either the
stainless steel bowl or the plastic mixing
bowl with the twin beating whisks and dough
hook, see figure 1. Or you may have the
standard dough hook or the professional
dough hook. Additional mixing bowls are
available as accessory items under the part
numbers: MUZ 7 ER1 and/or MUZ 7 KR1,
refer to SPECIAL ACCESSORIES section
at the back of this manual. The mixing bowl
with dough hook and twin beating whisks
consists of the following components,
dependent upon the system you have, see
figure 4:
The Bosch Concept Series Kitchen
Machines have been specially designed to
enable them to be stored in a drawer. Wind
the cord around the cord holder and, using
the carry grips, lift the power unit and place
in your chosen storage area.
Attachments
The attachment(s) that have been used
should be disassembled and washed, per
their specific instructions, dried and stored
for future use.
9
a.
b.
and that you have removed the motor drive
cover.
c.
1. Before using the mixing bowl and
dough hook for the first time, it
is recommended that the bowl,
anti-splash cover, filling funnel cap
and dough hook be washed. All
components of the mixing bowl and the
dough hook are dishwasher safe. Or
they may be washed in warm soapy
water. After washing, rinse well and dry
before using.
d.
The driveshaft can be removed for
cleaning by pushing down on the shaft,
as shown in figure 5a. After washing,
rinse and dry the driveshaft and replace
in the bowl by pressing it in, from the
bottom, as shown in figure 5b, until it
snaps into place.
e.
Figure 4.
4a. Bowl (either stainless steel or
plastic) with anti-splash cover and
filling funnel cap
a.
b.
4b. Standard dough hook (all systems
except MUM 7010 UC)
4c. Twin beating whisks
4d. Professional dough hook (MUM
7010 UC model only)
Figure 5.
4e. Bowl scraper
2. If you have not already done so, remove
the motor drive cover from the power
unit’s mono drive and place the mixing
bowl, whether the stainless bowl or the
plastic bowl, on the mono drive of the
power unit and turn the bowl counterclockwise with a slight downward
pressure until bowl is firmly seated on
the mono drive coupling, see figure 6.
How to Use Dough Hook
The dough hook and mixing bowl are
intended to be used to knead yeast doughs
and to mix cookie and pastry doughs and
also when adding nuts, chocolate chips,
dried fruit, hard butter or shortening,
hardened brown sugar, etc. to batters.
Use of mixing bowl with dough hook
CAUTION
Before beginning to attach this or any other
attachment, make sure that the power unit
is on a smooth, clean, suitable work
surface and switched to off position “O/Off,”
Failure to make sure that the bowl is
properly seated on the mono drive coupling
before the power unit is turned on can result
in damage to the bowl and/or coupling.
10
Plastic Bowl
8b), but the cover and cap should be in
place whenever the power unit is in
operation. The anti-splash cover and
cap serve to prevent the escape of flour
dust at the beginning of the stirring and
kneading process and also serves to
prevent accidental contact with the
moving dough hook.
Stainless Steel Bowl
Figure 6.
3. There are two styles of dough hook
used with the Bosch Machine, the
standard and the professional, but no
matter which one you have they are
mounted in the mixing bowl in the same
way: engage the dough hook on the
driveshaft of the mixing bowl by placing
it over the center column, as shown in
figure 7. Once in place, check to make
sure dough hook has engaged the
driveshaft by turning the dough hook
clockwise while pushing down until it
stops.
Standard
Dough Hook
a.
b.
Figure 8.
Placing into Operation w/Dough Hook
Make sure that the power unit is on a
smooth, clean, suitable work surface and
switched to off position, “O/Off.” Unwind the
electrical cord to the necessary length and
plug into a convenient outlet. The mixing
bowl with dough hook is now ready for
operation. See table 1 for examples
demonstrating the use of dough hook
attachment. Sample recipes may also be
found in recipes section, at the back of this
manual.
Professional
Dough Hook
Figure 7.
How to Use Twin Beating Whisks
All Bosch Concept Series Kitchen
Machines come with a twin beating whisk
assembly, see figure 4c.
4. Place the anti-splash cover on the bowl
so that the tabs on the bowl fit into the
recesses in the bowl cover and turn the
cover counterclockwise to fasten the
bowl cover to the bowl. See figure 8a.
The twin beating whisks and mixing bowl
are intended to be used for very light
substances, such as cream, egg whites,
sauces, batters and light pastry doughs
that are thin enough to pour.
The cover has an integral filling funnel
with a cap. The funnel cap may be
removed to add ingredients (see figure
11
OPERATION WITH DOUGH HOOK AND WHISK ASSEMBLY
Below you will find a table listing examples of how the dough hook and the whisk
assembly are to be used for various typical applications.
Attachment Ingredients
Twin Beating
Whisks
Speed
4
2 min.
(approx.)
20 eggs
(approx.)
Whipping Cream
3
2 min.
6 cups
(approx.)
Sponge Cake (any recipe)
Combine all ingredients
Whip
1
4
1/2 min.
Mix
Basic Cake Batter
Combine all ingredients
Mix
Dough Hook
Max.
Amount
Egg Whites (2)
Fold in flour mixture
Twin Beating
Whisks/Dough
Hook
Time
Cookie Dough
Cream, soft butter or shortening
and sugar using twin
beating whisks
Combine flour alternately with
liquid using dough hook
Stir in nuts, chocolate chips,
etc. using dough hook.
Yeast Dough
Combine all wet ingredients
Add flour in portions
M
(pulse)
4
4-6 min.
1
1/2 min.
4
3 min.
1
1/2 min.
4
3 min.
(approx.)
3x basic
recipe
(6 layers)
3 min
(approx.)
3x basic
recipe
(6 layers)
3x basic
recipe
(9 dozen
cookies)
2 or 3
1
1 or 2
1/2 min.
5 min.
(approx.)
3x basic
recipe
(10, 1 lb.
loaves)
Table 1. Examples of operation using whisk assembly and dough hook. Speed 1 should
be used for initial stirring and combining. Place all ingredients into the mixing bowl, liquids
first. Shortening must be soft (room temperature).
12
The driveshaft should also be removed
from the mixing bowl for cleaning, if it
has not already been done. See
previous section, covering mixing bowl
and dough hook, for instructions on how
to remove driveshaft.
The dough hook should be used for all
heavier substances such as cookie doughs,
yeast doughs, pastry doughs and other
heavy doughs.The dough hook should
always be used when adding nuts,
chocolate chips, dried fruits, hard butter or
other fats, hardened brown sugar, etc. to a
mixture.
2. If you have not already done so, remove
the motor drive cover and place the
mixing bowl on the mono drive of the
power unit and turn the bowl counterclockwise with a slight downward
pressure until bowl is firmly seated on
the mono drive coupling, see figure 4.
Use of mixing bowl with twin beating whisks
Before beginning to attach this or any other
attachment, make sure that the power unit
is on a smooth, clean, suitable surface and
switched to off position, “O/Off,” and that
you have removed the motor drive cover.
CAUTION
1. Before using the mixing bowl and twin
beating whisk assembly for the first
time, it is recommended that the bowl,
anti-splash cover, filling funnel cap and
twin beating whisk assembly be
washed. All components of the mixing
bowl and the twin beating whisk
assembly are dishwasher safe, except
the whisk holder.
Failure to make sure that the bowl is
properly seated on the mono drive coupling
before the power unit is turned on can result
in damage to the bowl and/or coupling.
3. Place and engage the twin beating
whisk assembly on the driveshaft of the
mixing bowl as shown in figure 10a.
a.
b.
The whisks may be removed from the
whisk holder as shown in figure 9a, and
washed in the dishwasher along with
the mixing bowl and other components.
The whisk holder should be washed in
warm soapy water. After washing, rinse
well and dry the whisk holder before
reattaching the whisks as shown in
figure 9b.
a.
Figure 10.
b.
4. Place the anti-splash cover on the bowl
so that the tabs on the bowl fit into the
recesses in the cover, and turn the antisplash cover counterclockwise to
fasten the bowl cover to the bowl.
See figure 10b.
The anti-splash cover has an integral filling
funnel with a cap. The cap may be removed
Figure 9.
13
Removing Contents
Before beginning to remove the contents
from the mixing bowl, make sure that the
power unit has been turned to off position,
“O/Off.” Remove the anti-splash cover by
turning the cover clockwise and lifting off.
Once the cover has been removed, the
dough hook or the twin beating whisks may
be removed by turning the hook or whisk
assembly clockwise while lifting.
to add ingredients, but the cover and cap
should be in place whenever the power unit
is in operation. The anti-splash cover and
cap serve to prevent the escape of flour dust
at the beginning of the stirring process as
well as prevent splatter, and also serves to
prevent accidental contact with the moving
whisks.
Placing into Operation w/Twin Beating
Whisks
Make sure that the switch is in the off
position, “O/Off.” Unwind the electrical cord
to the necessary length and plug into the
wall outlet. The bowl with whisk assembly
is now ready for operation. See table 1 for
examples demonstrating the use of the twin
beating whisks.
The mixing bowl can be removed from the
power unit by turning the bowl clockwise
while lifting.
The contents may now be used as desired.
Care and Cleaning
of Bowl and Its Accessories
The mixing bowl, twin beating whisks
(except for the whisk holder), dough hook
anti-splash cover, filling funnel cap, and bowl,
either the stainless steel bowl or plastic
bowl, are dishwasher safe.
Mixing bowl tips:
1. When using the mixing bowl to knead
or mix a recipe designed to be
prepared by hand, you will find that with
the Bosch Kitchen Machine you can
usually place all the ingredients in the
mixing bowl at once. When doing this,
always place the liquids in first. This
will assure more thorough mixing.
To facilitate cleaning:
> The driveshaft should be removed
from the mixing bowl, see figure 5;
and
> The whisks should be removed from
the whisk holder, see figure 9a.
2. When adding ingredients to a mixture:
a. Turn the rotary switch to a lower
speed;
b. Remove the cap from the filling
funnel;
c. Add the ingredients through the
funnel opening and replace the cap.
It is recommended that the whisk holder
be washed by hand in warm soapy water,
rinsed well and dried after each use.
The power unit of the kitchen machine
should be cleaned using a clean, damp
cloth only. Never use coarse or caustic
cleaning products to clean this appliance.
Never immerse the power unit in water.
3. If a large batch of dough is to be left in
the mixing bowl and allowed to rise, the
cover should be removed and placed
only loosely on the bowl so that it is
free to move if the dough should begin
to press on it.
14
Blender with Unbreakable Plastic Jar
(MUZ 7 MX1)
How to Use Blender
Either this plastic blender or the stainless
steel blender are available as accessory
items under the part numbers:
• MUZ 7 MX1
for blender with polycarbonate jar;
or
• MUZ 7 MX3
for blender with stainless steel jar.
WARNING
1. There is a risk of injury from sharp
blades when using the blender
attachment.
2. Keep hands and utensils out of the
blender jar while it is attached to the
power unit.
3. Blades are sharp. Handle carefully.
4. To avoid injury, never place blade
assembly on power unit without
blender jar properly attached.
5. Always operate the blender with the
cover in place.
6. The use of attachments, including
canning jars, not recommended by
the manufacturer, may cause a risk
of personal injury.
7. When blending hot and/or frothing
liquids, process a maximum of 18 fluid
ounces (0.5 litres) at a time.
The blender has been designed for crushing
ice; mixing liquids; pureeing vegetables;
preparing special diet and infant foods;
pulverizing fruit, vegetables, nuts and dried
bread (for bread crumbs); and preparing
mayonnaise and sauces.
Before beginning to use this or any other
attachment, make sure that the power unit
is on a clean, smooth, suitable work
surface and switched to off position, “O/Off,”
and that you have removed the motor drive
cover.
The MUM 7100 UC, MUM 7150 UC and the
MUM 7220 UC Bosch Concept Series
Kitchen Machines include the MUZ 7 MX1
blender accessory. The blender accessory
consists of, figure 11:
1. Before using the blender for the first
time, it is recommended that the
blender jar cover, closure/funnel and
blade/base assembly be washed. All
components, except the blade/base
assembly, are dishwasher safe.
Remove the blade/base assembly from
the blender, see figure 12.
CAUTION
Blade/base assembly is very sharp.
Handle with care.
The blade/base assembly may be
easily removed, as shown in figure 12a,
by inverting the blender and pressing
down on the quick release handle and
turning it counterclockwise until it
stops and then lifting up.
Figure 11.
11a.
11b.
11c.
11d.
Cover closure/funnel
Cover
Blender jar
Blade/base assembly.
15
a.
Normally when blending, the blender jar
should be filled with the entire amount of
material to be blended, if possible, before
switching the appliance on. The cover and
cover closure should always be in place after
filling the blender jar and before switching
the power unit to On. Any subsequent
additions to the blended material should be
made through the cover opening, see figure
14. For solids and/or granular material,
remove the cover closure/funnel to add the
material, as shown in figure 14a. For liquids,
the closure/funnel may be left in place and
the liquids added by pouring it into the
closure/funnel, see figure 14b.
b.
Figure 12.
Wash the blade/base assembly under
running water. Do not place the blade/
base assembly in the dishwasher or
allow it to stand in water. This will tend
to wash out the lubricant. After
cleaning, rinse thoroughly and dry
before using.
2. To assemble or reassemble blade/base
assembly into the blender, insert the
blade/base assembly into the blender
jar as shown in figure 12b, press
down on the quick release handle of
the blade/base assembly and turn
clockwise to the stop. The blade/base
assembly is then back in place.
Figure 14.
Example of Use of Blender
To familiarize you with the operation of the
blender, a sample recipe for mayonnaise is
provided below:
3. If you have not already done so, remove
the motor drive cover and place the
blender on the mono drive and turn
counterclockwise to lock the blender
in place.
a.
1
1/3
2
b.
1
1/2
1/2
2/3
Mayonnaise Recipe
whole egg
cup of vegetable oil
tablespoons lemon juice or light
vinegar
teaspoon sugar
teaspoon dry mustard
teaspoon of salt
cup of vegetable oil
Mix all ingredients, except final 2/3’s cup
of oil, for a few seconds at speed 1, then
quickly pour the oil in through the opening
in the cover in a uniformly thick stream, as
shown in figure 14b. Operate the blender at
speeds 1 or 4 until mixture is thick and
smooth (approximately 10-20 seconds).
Makes 1 1/4 cups.
Figure 13.
Placing Blender into Operation
Make sure that the switch is in the off
position, “O/Off.” Unwind the electrical cord
to the necessary length and plug into wall
outlet. The blender is now ready for
operation.
16
Tips:
The power unit of the kitchen machine
should be cleaned with a clean, damp cloth
only. Never use coarse or caustic cleaning
products to clean this appliance. Never
immerse the power unit in water.
The blender should be operated with careful
consideration as to what is required and/or
desired. The speed at which the blender is
operated and the length of operation for a
given job will depend upon the degree of
fineness desired or the amount being
blended.
Slicer/Shredder, w/Unbreakable Bowl
(MUZ 7 TS1)
When the blender is being used on dry
materials, such as nuts or dry bread, the
best results will be obtained when the
blender jar is filled with approximately 1/2
cup of material to be blended.
WARNING
1. Blades on discs are sharp. Handle
carefully. Do not grip the discs by the
blades.
2. When operating slicer/shredder keep
hands clear of filling tube. Only work
with pusher.
3. Always operate the slicer/shredder with
the cover in place.
If the blender does not start (even after trying
the highest speed) after having switched it
On and the control status indicator is
flashing, the blade has become blocked by
the contents. The power unit should be:
1. Switched to off, “0/Off,” and unplugged.
2. The mixture should be removed and the
contents at the bottom of the jar
loosened.
The MUM 7220 UC Bosch Concept Series
Kitchen Machine includes the MUZ 7 TS1
slicer/shredder attachment. The slicer/
shredder attachment consists of, figure 15:
Removing Contents
Before beginning to remove the contents
from the blender, make sure that the power
unit has been turned to off position “O/Off”.
Remove the blender from the power unit by
turning the blender to the clockwise while
lifting. With the blender removed from the
power unit, the contents of the blender may
now be poured into a suitable container or
bowl, as desired.
a.
b.
c.
d.
e.
Cover closure/pusher
Cover
Unbreakable 12-cup capacity bowl
Driveshaft
3 slicer/shredder discs:
• reversible slicing disc
• reversible shredding disc
• grating disc
f. disc holder
g. stabilizing pin
Care and Cleaning of Blender
All components of the blender, except the
blade/base assembly, are dishwasher safe.
It is recommended that the blade/base
assembly be cleaned only under flowing
water rather than in the dishwasher. Soap
and detergent will tend to wash out the
bearing lubricant of the blade/base
assembly. Do not use scouring cleaners on
any of the blender parts.
17
Figure 15.
Slicer/shredder, intended use
WARNING
The blades on the discs are very sharp.
Handle with care.
The slicer/shredder attachment has been
designed for slicing, shredding and/or
grating of vegetables, as well slicing/
shredding of soft cheeses and sausages
or meat and grating of vegetables and hard
cheese.
All components of the slicer/shredder are
dishwasher safe. The driveshaft can be
removed for cleaning. After washing, rinse
well and dry before using.
Use of Slicer/Shredder
2. To assemble the slicer/shredder:
a. If the driveshaft is not presently
inserted in the bowl, insert
driveshaft as shown in figure 15.
b. Place slicer/shredder bowl on
power unit by placing over mono
drive and while pressing down turn
it counterclockwise to stop and
lock the bowl in place, see figure
16a.
c. Select disc to be used and place
on disc holder and place over
driveshaft, see figure 16b.
Before beginning to use this or any other
attachment, make sure that the power unit
is on a smooth, clean, suitable work
surface and switched to Off position,
“O/Off,” and that you have removed the
motor drive cover.
1. Before using the slicer/shredder for the
first time, it is recommended that the
bowl, driveshaft, cover, closure/pusher,
discs, disc holder and stabilizing pin
be washed.
18
b.
2. For short or circular slices, place food
in the feeding tube on end. For
example, If you wish to have circular
slices of zucchini or carrots:
• cut to length not to extend above the
top of the feeding tube.
• place the cut zucchini or carrots in
the feeding tube on end until the
feeding tube is packed.
d. If stabilizing pin is not in cover,
insert pin, see 15e. Then place
cover on bowl, making sure the tabs
on the cover enter the recesses in
the bowl, and turn counterclockwise
to stop, see figure 17.
To slice a single narrow item, a carrot for
example:
• place the carrot in the feeding funnel
opposite the cutting edge of the disc.
a.
Figure 16.
The wall of the feeding funnel will then serve
to hold the piece vertical.
When using the slicer/shredder be sure to
watch the level in the bowl and stop the
slicing, shredding or grating before the level
of the material being sliced, shredded or
grated reaches the level of the disc holder.
Slicer/shredder tips:
1. Shopping for fruits and vegetables that
will fit into the feeding funnel will simplify
food preparation.
Figure 17.
Placing Slicer/Shredder into Operation
Make sure the power unit is on a smooth,
clean, suitable work surface and switched
to the Off position, “O/Off.” Unwind the
electrical cord to the necessary length and
plug into a convenient outlet. The slicer/
shredder is now ready for use.
2. Foods that are to be used together may
be sliced together. This can be used to
your advantage. For example, green
onions and celery are often used
together, but feeding the green onions
into the feeding funnel alone is difficult.
Try slicing the green onions at the same
time as the celery by interspersing
them in the feeding funnel with the
celery.
Place items to be sliced, shredded or
grated in feeding funnel and be sure to use
the pusher to feed items into the discs when
in operation.
3. Use the slicing disc to shred lettuce.
Learning how to feed food properly into the
feed funnel is the most important factor for
proper slicing and grating:
1. For long slices or long shreds, place
food into the feeding funnel lengthwise.
4. Do not overcook potatoes that are to
be sliced. Also it is recommended that
you let them cool first. Potatoes must
be cool and firm to obtain the regular
slices.
19
Food Processor with Unbreakable Bowl
(MUZ 7 MM2)
If the slicer/shredder does not start (even
after trying the highest speed) and the
indicator above the rotary dial is flashing:
the disc has become blocked by the
contents. The power unit should be:
WARNING
1. There is a risk of injury from sharp
blades when using the food processor
accessory.
2. Blades are sharp. Handle carefully.
3. Always operate the food processor
accessory properly assembled with
the cover in place.
1. Switched to Off position, “O/Off,” and
unplugged.
2. The top cover should be removed and
the items causing the blockage
removed.
The MUM 7150 UC Bosch Concept Series
Kitchen Machine includes the MUZ 7 MM2
food processor accessory. The food
processor accessory consists of, figure 18:
Removing Contents
Before beginning to remove the contents
from the slicer/shredder, make sure that the
power unit has been turned to the Off
position, “O/Off.” Remove the slicer/
shredder from the power unit by turning the
slicer/shredder bowl clockwise while lifting.
With the slicer/shredder removed from the
power unit, remove the top cover, by turning
it clockwise while lifting. Next lift the disc
holder and disc out of the bowl by grasping
the knob of the disc holder that is protruding
through the center of the disc. The contents
of the slicer/shredder may now be poured
into a suitable container or bowl, as desired.
Care and Cleaning
of Slicer/Shredder
All components of the slicer/shredder are
dishwasher safe. It is recommended that
the driveshaft be removed prior to placing
the bowl in the dishwasher. Do not use
scouring cleaners on any of the slicer/
shredder parts.
Figure 18.
The power unit of the kitchen machine
should be cleaned with a clean, damp cloth
only. Never use coarse or caustic cleaning
products to clean this appliance. Never
immerse the power unit in water.
18a. 5-cup capacity bowl with cover and
pusher/measuring cup.
18b. food processor blade
18c. 3 discs
• reversible slicing disc
• reversible shredding disc
• grating disc
18d. disc holder
20
How to Use the Food Processor Blade
The food processor blade and its bowl are
intended to be used for mincing, pureeing
and pulverizing of fruit, vegetables, meat,
nuts and dried bread (for bread crumbs) and
the preparation of sauces, special diet and
infant foods and mixing.
Note: The processor blade should not be
used to process hard cheeses
(Parmesan, Romano, etc.)
Figure 19.
4. Food to be processed may be placed
in the bowl now or added after the bowl
cover has been put in place.
Use of 5-cup capacity bowl with food
processor blade
Before beginning to attach this or any other
attachment, make sure that the power unit
is on a smooth, clean, suitable work surface
and switched to the Off position, “O/Off,” and
that you have removed the motor drive cover.
5. Place the cover on the bowl, as shown
in figure 20a. There is a safety
interlock in the handle of the 5-cup
capacity bowl that is engaged by the
cover. Push up on the interlock button
(step 1) and turn the cover (step 2)
counterclockwise until stop and
interlock is engaged.
1. Before using the food processor for
the first time, it is recommended that
the bowl, bowl cover, pusher/
measuring cup and food processor
blade be washed. All components of
the food processor attachment are
dishwasher safe. Or they may be
washed in warm soapy water. After
washing, rinse well and dry before
using.
2. If you have not already done so,
remove the motor drive cover from the
power unit’s mono drive and place the
bowl on the mono drive of the power
unit and turn the bowl counterclockwise with a slight downward
pressure until the bowl is firmly seated
on the drive coupling, see figure 19a.
Figure 20.
Note: The processor blade will not turn
when the power unit is started
unless the cover has properly
engaged the interlock. This is a
special safety feature of the food
processor bowl.
3. Grasping the processor blade by the
knob at the top of the center column,
lift it up and place it over the center
column of the bowl, see figure 19b.
Once in place, check to make sure
that the blade has engaged the
driveshaft by turning the blade slightly
clockwise.
The cover has an integral feeding funnel
with a pusher/measuring cup. The
pusher/measuring cup may be
removed to add ingredients, but the
cover and pusher must be in place
whenever the power unit is in operation.
21
• Almonds, nuts
Place nuts approximately 1/4 pound at a
time (100 g.) into the bowl dry. Use speed
4 for approximately 1 - 1 1/2 minutes.
Placing into Operation
with Food Processor Blade
Make sure that the power unit is on a
smooth, clean, suitable work surface and
switched to the Off, “O/Off,” position. Unwind
the electrical cord to the necessary length
and plug into a convenient outlet. The 5-cup
capacity bowl with food processor blade is
now ready for operation.
• Meat
Do not process more than 3/4 of a pound
at a time (375 g.). Remove the bones,
gristle and tendons and cut meat into
pieces suitable to fit through the feeding
tube.
The processor blade sits low in the bowl,
near the bottom. Food to be processed must
be fed through the feeding funnel using the
pusher. The food is then minced or pureed
near the bottom of the bowl by the spinning
blade. Food should be prepared as usual
(wash, dry, peel, etc.) and cut into pieces
to readily fit through the feeding funnel.
Note: Before processing, spices or bread
maybe added as called for in your recipe.
Use speed 4, or “M,” until desired result
is obtained (approximately 30 - 60
seconds).
• Pureeing
Fruits, vegetables and cheeses with
ingredients and spices may also be
processed. Do not process more than
3/4 of a pound at a time (375 g.). Use
speed 4 or “M” until desired result is
obtained (approx. 1 minute).
The degree of mincing desired, to a great
extent, depends upon the intended purpose
and the individual taste of the preparer, so
the times listed below in the examples
should be taken as a general guide only.
Also, the processing times depend upon
the quantity of food being processed; that
is, for small quantities and/or coarser result,
use a shorter operating time, for larger
quantities and/or finer result, use a longer
operating time.
• Mayonnaise
Using the recipe from the blender section,
place ingredients into the food processor
bowl, except the final 2/3 cup of vegetable
oil. Mix all the ingredients briefly, then
add the rest of the vegetable oil. Use
speed for approximately 1 1/2 minutes.
Examples of Use of Food Processor
To familiarize you with the operation of the
food processor, below you will find some
typical uses:
• Herbs (except chives)
Place herbs, up to an amount of
approximately 1 tablespoon (10 g.) into
the bowl dry. Use speed 4, or “M,” the
momentary “pulse” position, for 20-30
seconds.
• Onions or Garlic
Cut onions into quarters. Processing
approximately 1/4 pound at a time
(100 g.) use “M,” briefly (5-7 seconds)
until desired consistency is obtained.
Figure 21.
22
The disc holder, three discs and its 5-cup
capacity bowl are intended to be used for
slicing, shredding and/or grating of
vegetables, as well slicing/shredding of soft
cheeses and sausages or meat and grating
of vegetables and hard cheeses.
Removing Contents
Before beginning to remove the contents
from the food processor, make sure that the
power unit has been turned to the Off
position, “O/Off.” Remove the top cover from
the bowl by depressing the interlock button
on the handle, step 1, and turning the cover
clockwise, step 2, while lifting, see figure
21a. With the cover removed the bowl can
be removed from the power unit by turning
it clockwise while lifting, see figure 21b.
The contents of the bowl may now be
poured into a suitable container or bowl, as
desired. Be sure to hold the processor blade
in the bowl by placing a finger on the top of
the processor blade’s center column while
pouring.
Use of disc holder and discs
Before beginning to attach this or any other
attachment, make sure that the power unit
is on a smooth, clean, suitable work surface
and switched to the Off position, “O/Off,” and
that you have removed the motor drive cover.
1. Before using the bowl with the disc
holder and discs for the first time, it is
recommended that the bowl, bowl
cover, pusher/measuring cup, disc
holder and discs be washed. All
components of the food processor
attachment are dishwasher safe. Or
they may be washed in warm soapy
water. After washing, rinse well and
dry before using.
Next lift the processor blade out of the bowl
by grasping the knob of the center column
of the processor blade and lifting.
CAUTION
Processor blade is very sharp.
Handle with care.
2. If you have not already done so,
remove the motor drive cover from the
power unit’s mono drive and place the
bowl on the mono drive of the power
unit and turn the bowl counterclockwise with a slight downward
pressure until the bowl is firmly seated
on the drive coupling, see figure 19a.
Care and Cleaning
of Food Processor Blade and Bowl
All components of the food processor are
dishwasher safe. Do not use scouring
cleaners on any of the food processor parts.
3. Select disc to be used and place on
disc holder and place over driveshaft,
see figure 22a.
The power unit of the kitchen machine
should be cleaned with a clean, damp cloth
only. Never use coarse or caustic cleaning
products to clean this appliance. Never
immerse the power unit in water.
How to Use Discs w/5-Cup Capacity Bowl
The food processor attachment provided with
the MUM 7150 UC Bosch Concept Series
Kitchen Machine also has a disc holder with
3 discs, in addition to the processor blade,
see figure 18.
Figure 22.
23
Removing Contents
Before beginning to remove the contents
from the 5-cup capacity food processor bowl,
make sure that the power unit has been
turned to the Off position, “O/Off.” Remove
the top cover from the bowl by depressing
the interlock button on the handle, step 1,
and turning the cover clockwise, step 2,
while lifting, see figure 21a. With the cover
removed the bowl can be removed from the
power unit by turning it clockwise while
lifting, see figure 21b. Next lift the disc holder
and disc out of the bowl by grasping the
knob of the disc holder that is protruding
through the center of the disc.
4. Place the cover on the bowl, as shown
in figure 22b. There is a safety
interlock in the handle of the 5-cup
capacity bowl that is engaged by the
cover. Push up on the interlock button,
step 1, and turn the cover, step 2,
counterclockwise until it stops and
the interlock is engaged.
Note: The disc and disc holder will not
turn when the power unit is started
unless the cover has properly
engaged the interlock. This is a
special safety feature of the food
processor bowl.
The cover has an integral feeding funnel
with a pusher/measuring cup. The
pusher/measuring cup may be
removed to add ingredients, but the
cover and pusher must be in place
whenever the power unit is in operation.
CAUTION
Blades on discs are very sharp.
Handle with care.
Placing into Operation with Discs
Make sure the power unit is on a smooth,
clean, suitable work surface and switched
to the Off position, “O/Off.” Unwind the
electrical cord to the necessary length and
plug into a convenient outlet. The 5-cup
capacity food processor bowl is now ready
for use with the disc you have selected.
The contents of the bowl may now be
poured into a suitable container or bowl, as
desired.
Care and Cleaning
of Discs, Disc Holder and Bowl
All components of the food processor are
dishwasher safe. Do not use scouring
cleaners on any of the slicer/shredder parts.
Place items to be sliced, shredded or grated
in feeding funnel and be sure to use the
pusher to feed items into the discs when in
operation.
Refer to Slicer/Shredder section of this
manual, page19, for examples and tips on
how the discs may be used for slicing,
shredding and grating.
The power unit of the kitchen machine
should be cleaned with a clean, damp cloth
only. Never use coarse or caustic cleaning
products to clean this appliance. Never
immerse the power unit in water.
Just as when using the slicer/shredder, be
sure to watch the level in the bowl and stop
the slicing, shredding or grating before the
level of the material being sliced, shredded
or grated reaches the level of the disc
holder.
24
Service and Repair
TROUBLESHOOTING
The Bosch Concept Series Kitchen
Machines require no special care other than
the care and cleaning noted in this manual.
If you are having a problem with your
machine, before calling our Customer
Support group, please refer to the
TROUBLESHOOTING section below. If after
reviewing the troubleshooting section and
trying its remedies you are still having a
problem, please do contact us by either
writing to us at:
•
Status
Indicator
Off
A circuit breaker may have
tripped or a fuse has blown in
power supply circuit. Reset
circuit breaker or replace
fuse.
Status
Indicator
Flashing
Power supply to the power
unit has been interrupted and
become reestablished (there
was a temporary power
outage).
1. Turn the power unit to Off
and wait 5 seconds.
2. Restart.
Status
Indicator
Flashing
boschsmallappliances@bshg.com
or calling us at:
•
Possible Cause and Remedy
Bosch Small Appliances
Customer Support
BSH Home Appliances
5551 McFadden Avenue
Huntington Beach, CA 92649
or e-mailing us at:
•
Problem
The power unit has been
overloaded; for example, the
blender blade may have
become blocked.
1. Turn the power unit to Off
and unplug.
1 (866) 44BOSCH
[1 (866) 442-6724]
2. Remove contents of
attachment being used
and loosen whatever has
caused the jam.
If you do write to us, please include your
e-mail address or a daytime telephone
number where you may be reached.
3. Reinstall attachment and
restart.
Also, to view our full product line, please
visit our Web site:
• www.boschsmallappliances.com
25
Sample Recipes
Fruit Smoothies
Salsa
2
2
1/2
1
1-2
1
Chop the following ingredients in Bosch
blender or food processor, on speed 3 or 4:
1-4
1
1/8
8
Dried Arabol Chilies
(start with one, add more for
increased spiciness)
clove garlic
cup water
ounces tomato sauce (add
half)
cups fruit juice
cups frozen fruit
can frozen juice concentrate
cup fruit flavored yogurt
cups of ice
fresh banana
Place all ingredients in Bosch blender and
mix until smooth, on speed 3 or 4.
Experiment with different flavor combinations
such as tropical, berry or melon.
Next add:
1 & 1/2 teaspoons oregano
3/4
teaspoons cumin
1
bunch of fresh cilantro
1
pinch of salt
second half of tomato sauce
French Bread
4
4
6
2
1
10 -12
4
Blend all ingredients, on speed 1 or 2, until
smooth.
Pesto
cup loosely packed basil
leaves
1/2
cup grated parmsean
1/3-1/2 cup olive oil (enough for
desiredconsistency)
1-2
cloves garlic
1/4
cup shelled pinenuts
tablespoons active dry yeast
cups hot water
tablespoons sugar
tablespoons salt
cup vegetable oil
cups of flour (white or wheat)
tablespoons gluten
1
Place all ingredients in Bosch mixing bowl.
Thoroughly knead on speed 1 or 2 (8 - 10
minutes). Let rise in the bowl 10 minutes,
then punch down. Punch down 4 or 5 times.
Divide into 3 - 4 regular loaf pans or shape
into rounds. Slash tops with sharp knife and
brush with egg wash. Let raise until doubled
in size. Bake 30 minutes at 400 °F.
Lightly toast pinenuts. Let cool. Place olive
oil in Bosch blender or food processor. Turn
on power and gradually add parmesan
cheese, garlic and basil leaves. Process,
on speed 1 or 2, until smooth. Add pinenuts
and blend thoroughly.
Toss with cooked pasta or spread on bread
or crackers.
26
Oatmeal
Cookies
2
1
2
1
1 - 3/4
1
1/2
3
1
Chocolate
Chip
cups packed brown sugar
cup shortening
eggs
teaspoon vanilla
cups flour
teaspoon baking soda
teaspoon salt
cups quick-cooking rolled oats
cup chocolate chips
Cream the brown sugar, shortening, eggs
and vanilla in the mixing bowl, on speed 1
or 2. Add flour, baking soda and salt. Blend
well, stir in rolled oats and chocolate chips
by hand. Drop by spoonfuls onto greased
baking sheets. Bake in 350 °F oven for 8 10 minutes. Cool before removing from pan.
Makes 5 dozen.
Acknowledgement:
The sample recipes listed bove were submitted by:
Salsa - Caroline Ciarelli, BSH Home
Appliances
Pesto - Kitchen Resource
Fruit Smoothies - Marni Rader, BSH
Appliances
French Bread - Kitchen Resource
Oatmeal Chocolate Chip Cookies Kitchen Resource.
27
Important Notes
28
Important Notes
29
SPECIAL ACCESSORIES
30
BOSCH Small Appliance Warranty
BSH Home Appliances (“BOSCH”) warrants all new small appliances to be free from original
defects in design, materials and workmanship for one (1) year after the sale to the original
owner.
Within the stated warranty period, BOSCH will repair or replace, at its sole option, any
small appliance or parts thereof which prove defective under the conditions of normal use
and service at no charge to you. It is the owner’s responsibility to return the appliance for
repair. Repaired and replacement small appliances and parts shall be the same or as
close in appearance as possible to the original for the purposes of this warranty.
Should you require service of your BOSCH small appliance, please contact customer
service at 1-866-44-BOSCH. Repair of BOSCH appliances should only be performed by
qualified technicians.
This warranty is limited to the original consumer purchase and is not transferable. Specifically
excluded from this warranty are failures caused by accident, misuse, neglect, abuse,
including tampering, use of frequency or voltage other than marked on the product, and
use for commercial purposes.
To the extent allowed by law, this warranty sets out your exclusive remedies, whether for
negligence or otherwise. BOSCH will not be liable for any consequential or incidental
damages, losses or expenses. THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESSED
WARRANTIES. ANY WARRANTY IMPLIED BY LAW, WHETHER FOR
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE,
SHALL BE EFFECTIVE ONLY FOR THE PERIOD THAT THIS EXPRESSED WARRANTY
IS EFFECTIVE. BOSCH DOES NOT ASSUME ANY RESPONSIBILITY FOR INCIDENTAL
OR CONSEQUENTIAL DAMAGES.
No attempt to alter, modify or amend this warranty shall be effective unless authorized in
writing by an officer of BOSCH. Some states do not allow limitations on how long implied
warranties last or the exclusion or limitation of incidental or consequential damages, so
the foregoing limitations and exclusions may not apply to you. This warranty gives you
specific legal rights and you may also have other rights which vary from state to state.
31
Looking for more information about BOSCH products?
Visit our Web site:
www.boschsmallappliances.com
32