Setup guide | Bose AM324443 Home Theater System User Manual

Cover_8.5x6.5_Setup Guide_3L.fm Page 1 Monday, November 9, 2009 2:47 PM
LIFESTYLE V35/V25 HOME ENTERTAINMENT SYSTEMS
LIFESTYLE T20/ T10 HOME THEATER SYSTEMS
®
®
©2010 Bose Corporation, The Mountain,
Framingham, MA 01701-9168 USA
AM324443 Rev.00
Setup Guide | Guía de instalación | Guide d'installation
ResoluteVigilantSetup.book Page ii Monday, December 7, 2009 11:59 AM
TAB 8
TAB 7
TAB 6
TAB 5
TAB 4
TAB 3
TAB 2
English
SAFETY INFORMATION
Please read this guide
CAUTIONS:
Please take the time to follow the instructions in this guide
carefully. They will help you set up and use your system properly
so you can enjoy its advanced features. Please save this guide for
future reference.
• Make no modifications to the system or accessories. Unauthorized
alterations may compromise safety, regulatory compliance, and
system performance, and may void the warranty.
• Long-term exposure to loud music may cause hearing damage.
It is best to avoid extreme volume when using headphones,
especially for extended periods.
Notes:
The lightning flash with arrowhead symbol within an
equilateral triangle alerts the user to the presence of
uninsulated, dangerous voltage within the system enclosure
that may be of sufficient magnitude to constitute a risk of
electric shock.
The exclamation point within an equilateral triangle alerts
the user to the presence of important operating and
maintenance instructions in this guide.
WARNINGS:
• To reduce the risk of fire or electrical shock, do not expose the
product to rain or moisture.
• Do not expose this apparatus to dripping or splashing, and do not
place objects filled with liquids, such as vases, on or near the
apparatus. As with any electronic products, use care not to spill
liquids into any part of the system. Liquids can cause a failure
and/or a fire hazard.
• Do not place any naked flame sources, such as lighted candles,
on or near the apparatus.
• Keep the remote control battery away from children. It may cause a
fire or chemical burn if mishandled. Do not recharge, disassemble,
heat above 100ºC (212ºF), or incinerate. Dispose of used batteries
promptly. Replace only with a battery of the correct type and model
number.
• Contains small parts that may be a choking hazard.
Not suitable for children under age 3.
ii
• Where the mains plug or appliance coupler is used as the disconnect device, such disconnect device shall remain readily operable.
• The product must be used indoors. It is neither designed nor tested
for use outdoors, in recreation vehicles, or on boats.
• This product is intended to be used only with the power supply
provided.
• The product label is located on the bottom of the product.
Additional safety information
See the additional instructions on the Important Safety Information
sheet enclosed in the shipping carton.
Batteries
Please dispose of used batteries properly, following any
local regulations. Do not incinerate.
Class B emissions
This device complies with FCC and Industry Canada RF radiation
exposure limits set forth for general population. It must not be
co-located or be operating in conjunction with any other antennas
or transmitters.
This product conforms to all EU Directive requirements as
applicable by law. The complete Declaration of Conformity
can be found at www.Bose.com/compliance.
©2010 Bose Corporation. No part of this work may be reproduced,
modified, distributed, or otherwise used without prior written permission.
ResoluteVigilantSetup.book Page 1 Monday, December 7, 2009 11:59 AM
English
TAB 2
TAB 3
TAB 4
TAB 5
TAB 6
TAB 7
TAB 8
SYSTEM SETUP
Welcome
Starting with Kit 1, unpack each kit and set up its
contents before unpacking the next one.
®
®
Thank you for choosing a Bose LIFESTYLE system
for your home. This guide provides step-by-step
instructions for setting up your new system. There
are two phases to the setup process:
Physical setup phase: Placing the system
components and connecting them together.
Interactive setup phase: Completing your setup
following the interactive steps on your TV screen
provided by the Unify intelligent integration system.
Be sure to save all of the packing materials. These
provide the safest means for any necessary shipping
or transporting.
If any part appears damaged, do not attempt to use
it. Notify Bose or your authorized Bose dealer
immediately. For Bose contact information, refer
to the address sheet included in Kit 4.
TM
Unpacking
The parts of your new system are packaged in four
numbered kits plus a small box containing the
appropriate power cords:
•
•
•
•
•
11 Control console kit
2 Acoustimass module kit
®
3
4
Speaker kit
Interactive kit
Power cord kit (used with kits 1 and 2)
1
ResoluteVigilantSetup.book Page 2 Monday, December 7, 2009 11:59 AM
TAB 8
TAB 7
TAB 6
TAB 5
TAB 4
TAB 3
TAB 2
English
SYSTEM SETUP
1. Place the control console on a flat, stable surface
near your TV.
11
Control console kit
What you need for the following steps:
From Kit 1
Power supply
Control console
Control
console
Audio input cable
Note: Until your system is completely installed, it may be
helpful to keep the control console positioned for easy
access to its rear connection panel.
From the
power
cord kit
Power cord
2
HDMI cable
ResoluteVigilantSetup.book Page 3 Monday, December 7, 2009 11:59 AM
English
TAB 2
TAB 3
TAB 4
TAB 5
TAB 6
TAB 7
TAB 8
SYSTEM SETUP
2. Plug one end of the HDMI cable into an HDMI
INPUT connector on your TV.
If an HDMI cable is already connected to an
HDMI input on your TV, you can use this one.
Just disconnect the other end.
3. Plug the other end of the HDMI cable you are using
into the connector labeled HDMI OUT Video to
TV on the control console.
HDMI OUT
Video to TV
3
ResoluteVigilantSetup.book Page 4 Monday, December 7, 2009 11:59 AM
TAB 8
TAB 7
TAB 6
TAB 5
TAB 4
TAB 3
TAB 2
English
SYSTEM SETUP
4. Plug one end of the audio input cable into the
Acoustimass Module connector on the control
console.
®
Make sure the flat surface with the arrow on the
plug faces up.
5. Plug the power supply output cord into the control
console Power connector.
AC
power
cord
Power
Leave the other end of the cable on the floor.
You will be asked to connect it while setting up
the next kit.
Power supply
output cord
Acoustimass
Module
Power
supply
6. Remove a power cord
from the power cord kit.
7. Plug one end of the power cord into the power
supply. Make sure you push the plug in as far as
it can go.
8. Plug the other end of the power cord into a live
AC (mains) power outlet.
9. Continue with Kit
4
2
on the next page.
ResoluteVigilantSetup.book Page 5 Monday, December 7, 2009 11:59 AM
English
TAB 2
TAB 3
TAB 4
TAB 5
TAB 6
TAB 7
TAB 8
SYSTEM SETUP
1. Place the Acoustimass module on the floor at the
same end of the room as the TV. Make sure there is
a live AC outlet nearby.
2
®
Acoustimass module kit
What you need for the following steps:
From Kit 2
Acoustimass
module
Acoustimass module
2. Lay the module on its side and locate the
connector panel.
Connector
panel
From the
power
cord kit
Power cord
5
ResoluteVigilantSetup.book Page 6 Monday, December 7, 2009 11:59 AM
TAB 8
TAB 7
TAB 6
TAB 5
TAB 4
TAB 3
TAB 2
English
SYSTEM SETUP
CAUTION: DO NOT
stand the Acoustimass
module on its front or
back end.
®
4. Remove a power cord
from the power cord kit.
5. Plug one end of the power cord into the AC Power
connector on the Acoustimass module. Make sure
you push the plug in as far as it can go.
AC Power
3. Plug the free end of the audio input cable into the
Media Center connector on the Acoustimass
module.
Make sure the flat surface with the arrow faces the
front of the module.
Media Center
6. Plug the other end of the power cord into a live
AC (mains) power outlet.
7. Continue with Kit
6
3
on the next page.
ResoluteVigilantSetup.book Page 7 Monday, December 7, 2009 11:59 AM
English
TAB 2
TAB 3
TAB 4
TAB 5
TAB 6
TAB 7
TAB 8
SYSTEM SETUP
Front speaker cables
3
Speaker kit
What you need for the following steps:
From Kit 3: System speakers
(one set of the three types shown)
Center front (C)
Brown
Right front (R)
Light blue
Rear speaker cables
®
Jewel Cube speakers
(4) Left or right, front
or rear speaker
Left front (L)
White
(1) Center front speaker
Left rear (LR)
Light green
Right rear (RR)
Purple
®
Direct/Reflecting cube speaker arrays
(4) Left or right, front
or rear speaker
Note: You can place system speakers on wall brackets or
floor stands. To purchase these accessories, contact your
local Bose dealer or visit www.Bose.com.
(1) Center front speaker
®
Virtually Invisible single cube speakers
(5) Left or right, front or rear, and center front speaker
7
ResoluteVigilantSetup.book Page 8 Monday, December 7, 2009 11:59 AM
TAB 8
TAB 7
TAB 6
TAB 5
TAB 4
TAB 3
TAB 2
English
SYSTEM SETUP
1. Place the center front speaker on a stable and level
surface directly above or below the center of your
TV screen as in the following example.
Left front (L)
Right front (R)
2. Place one speaker to the left and one to the right of
the TV.
• Keep each speaker within 3 ft (1 m) of the TV
screen to prevent too much separation of the
sound from the picture. Vary this distance to suit
your room conditions and personal preference.
• If placing the speakers in an enclosed bookcase
shelf, position them at the front edge of the shelf.
®
Center front
(C)
8
®
• If you have Jewel Cube or Direct/Reflecting
cube speakers, rotate the cubes so that one
cube of each speaker points forward into the
room and the other points at a side wall to
create reflected sound.
ResoluteVigilantSetup.book Page 9 Monday, December 7, 2009 11:59 AM
English
TAB 2
TAB 3
TAB 4
TAB 5
TAB 6
TAB 7
TAB 8
SYSTEM SETUP
4. Locate the colored connectors on the bottom panel
of the Acoustimass module.
3. Place the rear speakers toward the back of the
room behind the viewers at ear height (when
seated) or higher, if possible.
Colored connectors
Left rear
(LR)
Right rear
(RR)
• Make sure the 50 ft (15.2 m) rear speaker cables
will reach from the speakers to the Acoustimass
module.
®
5. Plug the speaker cables into the Acoustimass
module connectors. Be sure to match each cable
plug to each connector by the color code.
• Aim the speakers away from the listeners to prevent them from pinpointing the exact location of the
sound source.
®
®
• If you have Jewel Cube or Direct/Reflecting
cube speakers, rotate the cubes so that one
cube of each speaker points forward into the
room and the other points at a side wall to
create reflected sound.
9
ResoluteVigilantSetup.book Page 10 Monday, December 7, 2009 11:59 AM
TAB 8
TAB 7
TAB 6
TAB 5
TAB 4
TAB 3
TAB 2
English
SYSTEM SETUP
6. Locate the speaker position markings on the free
ends of the speaker cables.
7. Using the speaker position markings, run each
cable out to its respective speaker as in the
following setup example of a room.
FRONT
SPEAKERS
Speaker position marking
(L, C, R, LR, or RR)
REAR
SPEAKERS
10
ResoluteVigilantSetup.book Page 11 Monday, December 7, 2009 11:59 AM
English
TAB 2
TAB 3
TAB 4
TAB 5
TAB 6
TAB 7
TAB 8
SYSTEM SETUP
8. Connect the speaker cable to the type of speaker
you have.
For Jewel Cube speakers:
®
9. Put the Acoustimass module in its final position:
• Upright (BEST) or on either side (ALTERNATE).
®
Insert the plug into the speaker
connector.
BEST
®
For Direct/Reflecting and
Virtually Invisible single
cube speakers:
ALTERNATE
• With the front opening facing into the room.
®
Press the button and insert the
wires. Connect the red-collared
wire to the red connector.
Connect the other wire to the
black connector.
Note: The rear speaker cables
for Direct/Reflecting and
Virtually Invisible cube speakers
are webbed together. You can
pull them apart as needed.
®
®
• At least 18 in (45 cm) from any TV to avoid
magnetic interference with the TV image. Move
it farther away if you still notice interference.
CAUTION: Do not put electronic media, such as video or
audio tapes, on or next to the module for long periods of
time. The magnetic field surrounding the module may
erase some or all of the recorded material.
CAUTION: DO NOT BLOCK the
ventilation openings on the module.
This can cause it to overheat.
10. Continue with Kit
4
on the next page.
11
ResoluteVigilantSetup.book Page 12 Monday, December 7, 2009 11:59 AM
TAB 8
TAB 7
TAB 6
TAB 5
TAB 4
TAB 3
TAB 2
English
SYSTEM SETUP
IMPORTANT!
4
• Before you start, make sure your speakers and
Acoustimass module are in their final
positions.
Interactive kit
What you need for the following steps:
• Do not connect any devices to the control
console at this time. The instructions provided
on your TV will tell you when to do this.
From Kit 4
1. Slide the battery compartment cover off the back
of the remote control.
AA (IEC LR6) batteries (4)
Remote control
with batteries
ADAPTiQ® audio
calibration
headset
Congratulations! At this point you have set up the
control console, the Acoustimass module, and the
speakers. You are now ready to turn on your system
and enter the interactive phase of the setup process
using the Unify intelligent integration system.
Battery compartment cover
®
TM
2. Install four AA (IEC LR6) batteries, matching the
polarity markings (+ and –) to the markings inside
the battery compartment.
3. Slide the battery cover back into place.
12
ResoluteVigilantSetup.book Page 13 Monday, December 7, 2009 11:59 AM
English
TAB 2
TAB 3
TAB 4
TAB 5
TAB 6
TAB 7
TAB 8
SYSTEM SETUP
4. Press the power button ( ) on the control console
to turn on your system.
Because the system is in a low power state when
in standby, it takes several seconds to start. When
the power light changes from blinking to steady
green, your system is ready to use.
Power
light
Other Kit 4 items
The remaining items in Kit 4 may or may not be
required to set up your LIFESTYLE system. For more
information on using these accessories or adding other
devices to your system at another time, see the
operating guide.
®
IR emitter cable
Stereo audio cable
AM antenna*
FM antenna*
Rubber feet
for Acoustimass
module
Rubber feet
for front center
speaker
5. Turn on your TV.
6. Using the remote that came with your TV, change
the TV input to the one that is connected to your
LIFESTYLE system.
®
®
7. Follow the instructions on your TV screen. You will
be prompted to do the following:
H
5 HH
225 00
VV 11
5// //TT
335 00
VV TT22
LLEE EE
YY YYLL
SSTT STT
FEE EES
FF
LLII LLIIFF
• Select your language.
®®®®®
®®®®®
SSS
MMM
TEEE
SSTST
SSYY S
TT MMMSS
NNT
EEEN TTEEE
MMM YYYSSTS
ININ
AAIN RRRSS
TTTA
RR ATTTEEE
TEEE
NTT EEEAA
EENN HHH
EE EEETT
ME
OMM OMMM
OO
O
HO
nnonn
ioioioi
atsatisatat
lilsilsil
utiuti
d’utd’ut
ed’ed’
ddiedied
Guii
|Gu|Gu
||Gu
riorioriorio
uaua
ususuaua
lluslusl
dededede
aaíaía
Guíí
|Gu|Gu
||Gu
eedee
idididi
GuGuGuGu
ggngg
ininini
atatatat
erererer
OpOpOpOp
• Optimize the audio from your system using the
ADAPTiQ audio calibration system.
®
• Connect audio/video devices to the
control console.
Operating guide
iPod/iPhonecompatible
dock*
USB flash drive
(for system
updating only)
®
• Configure your Bose remote to control your
connected devices.
®
*For LIFESTYLE V25 and V35 systems only.
13
ResoluteVigilantSetup.book Page 14 Monday, December 7, 2009 11:59 AM
TAB 8
TAB 7
TAB 6
TAB 5
TAB 4
TAB 3
TAB 2
English
SYSTEM SETUP
Applying rubber feet
If you have setup problems
When placing the Acoustimass module on bare floors,
you can attach the included rubber feet to the bottom
of the module for greater stability and to protect your
floor.
If you experience any difficulties during the setup
process, such as an unrecognized device remote or
a connection error, you can reactivate the interactive
setup mode at any time and correct or change part of
your system setup. See “Using the Setup Mode” in
your system operating guide.
Rubber feet
for
Acoustimass
module
For help in trying to resolve any problems, see the
troubleshooting table in your system operating guide.
®
Bottom panel
Contacting customer service
Vibration can cause speakers to move, particularly if
placed on a smooth surface like glass or highly
polished wood. If you are placing the center speaker on
such a surface, you can attach the included rubber feet
to the bottom of the speaker for greater stability.
Rubber feet
for
front center
speaker
14
Bottom panel
of center
speaker
For additional help in solving problems, contact Bose
Customer Service. See the address sheet included in
Kit 4.
®
®
Applicable only for LIFESTYLE V25 and V35
home entertainment systems
“Made for iPod” means that an electronic
accessory has been designed to connect
specifically to iPod and has been certified by
the developer to meet Apple performance
standards.
Apple is not responsible for the operation of this device or its
compliance with safety and regulatory standards.
iPod and iPhone are trademarks of Apple, Inc., registered in
the U.S. and other countries. All other marks are registered
trademarks and trademarks of Bose Corporation.
03.RV_SetupOG_Setup.fm Page 15 Monday, December 7, 2009 12:10 PM
English
TAB 2
TAB 3
TAB 4
TAB 5
TAB 6
TAB 7
TAB 8
15
LIFESTYLE V35/V25 HOME ENTERTAINMENT SYSTEMS
LIFESTYLE T20/ T10 HOME THEATER SYSTEMS
®
®
©2010 Bose Corporation, The Mountain,
Framingham, MA 01701-9168 USA
AM324443 Rev.00
Setup Guide | Guía de instalación | Guide d'installation
Download PDF

advertising