Cres Cor HJ-531-10-240 Operation Manual
Advertisement
Advertisement
Heated
Dish Dolly
Rev. 18 (5/06)
5925 Heisley Road • Mentor, OH 44060-1833
OPERATING and MAINTENANCE INSTRUCTIONS
Models: HJ-531-10-240 and HJ-531-13-180
JETSTREAM HEATED DISH DOLLY
FL-0508
Page 1 of 2
ELECTRICAL SPECIFICATIONS:
MODEL NO.
Volts Watts Amps Hertz Phase
HJ-531-10-240
HJ-531-13-180
120 1060 8.8
60 1
HJ-531-10-240-240
HJ-531-13-180-240
240 1060 4.4
60 1
Service
AC
AC
®
NSF/ANSI 4
®
C US
HOW TO INSTALL UNIT:
1.
2.
3.
Plug cord into receptacle in back of unit.
Turn clockwise to lock.
Plug other end into 15 Amp wall outlet.
MAINTENANCE:
HOW TO START UNIT:
1.
2.
Flip switch ON. Yellow light will come on.
Turn thermostat to #7 (150° F to 160° F / 66° C to
3.
71° C) which will warm the plates.
Hint: Dial has a range of #1 to #10
(60° F to 250° F / 16° C to 121° C).
4. Pre-heat dolly for 30 minutes.
5. Add plates.
HOW TO TURN UNIT OFF:
Flip switch OFF.
REPLACEMENT PARTS
Description
Heater Ass’y
Blower Kit
120 Volt 240 Volt
0811-074 0811-074-01
0769-005-K 0769-006-K1
Thermostat Kit 0848-062-K 0848-062-K
Yellow Light 0766-048 0766-045
Red Light
Receptacle
0766-047
0713-011
0766-046
0713-012
Cord Set
Switch
0810-031-01 0810-032-01
0808-011 0808-020
Call Toll-free: 877-CRES COR (273-7267) • Fax: 800-822-0393 • www.crescor.com
Heated
Dish Dolly
Rev. 18 (5/06)
FL-0508
Page 2 of 2
5925 Heisley Road • Mentor, OH 44060-1833
OPERATING and MAINTENANCE INSTRUCTIONS
Models: HJ-531-10-240 and HJ-531-13-180
JETSTREAM HEATED DISH DOLLY
TROUBLE-SHOOTING:
Failure
1. Yellow light not on.
2. Unit does not get hot.
3. Unit gets too hot or won’t shut off.
Cause
1a. Cord not plugged into dolly or wall outlet.
1b. Circuit breaker/fuse to wall outlet blown.
1c. Switch is off.
2a. Thermostat set too low.
3a. Defective electrical parts; unplug cord from wall outlet.
If the cause is none of the above, refer to our list of Authorized Service Centers, FL-1400.
BEFORE CLEANING CABINET:
1. Remove Power Cord from cabinet.
2. Do NOT hose cabinet with water.
3. Do NOT get water on controls.
4. Do NOT use abrasives or harsh chemicals.
2.
3.
4.
5.
6.
Cleaning Hints:
1.
Wipe up spills as soon as possible.
Clean regularly to avoid heavy dirt build-up.
Make a test spot with cleaner.
Follow manufacturer’s directions on cleaner.
Do not mix cleaners.
Avoid drips and splashes.
Dolly
Inside and Outside
(Aluminum)
SOIL
DIRT
CLEANER
Mild detergent* and hot water, or mild abrasive cleaner.
Steam (no strong alkaline additive)
METHOD
1. Use soft, damp cloth.
2. Rinse with hot water.
3. Wipe dry.
1. Rinse after steam cleaning.
2. Wipe dry.
FINGERPRINTS,
GREASE OIL
Detergent* and hot water.
1. Wipe with soft, damp cloth.
2. Rinse with hot water.
3. Wipe dry.
WATER SPOTS
Mild abrasive cleaner.
Oily or waxy cleaner.
Mild abrasive cleaner.
Apply with soft, clean cloth.
Wipe with damp cloth.
* Mild detergents include soaps and non-abrasive cleaners
LEGEND
SW
BM
TH
H
A
R
L5-15R
L6-15R
SWITCH (SPST)
BLOWER MOTOR
THERMOSTAT
HEATER
AMBER PILOT LIGHT
RED PILOT LIGHT
RECEPTACLE, 110V/15A
RECEPTACLE, 220V/15A
ELECTRICAL SPEC
120/240V 1000W
1 PHASE 60 HZ
AC SERVICE
Call Toll-free: 877-CRES COR (273-7267) • Fax: 800-822-0393 • www.crescor.com

Public link updated
The public link to your chat has been updated.
Advertisement