BOXLIGHT CINEMA 20HD Projector User Manual

USER'S GUIDE
CINEMA 20HD
HOME THEATER
PROJECTOR
TO THE OWNER
Before operating this projector, read this manual thoroughly and operate the projector properly.
This projector provides many convenient features and functions. Operating the projector properly enables you to
manage those features and maintains it in better condition for a considerable time.
Improper operation may result in not only shortening the product-life, but also malfunctions, fire hazard, or other
accidents.
If your projector seems to operate improperly, read this manual again, check operations and cable connections and try
the solutions in the “Trouble-shooting” section of the end of this booklet. If the problem still persists, contact
BOXLIGHT.
SAFETY PRECAUTIONS
WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE.
● This projector produces intense light from the projection lens. Do not stare directly into the lens as it could
possibly damage your eyes. Be especially careful that children do not stare directly into the beam.
● This projector should be set in the way indicated. If not, it may result in a fire hazard.
● Take appropriate space on the top, sides and rear of the projector
cabinet for allowing air circulation and cooling the projector.
Minimum distance should be taken. If the projector is to be built
into a compartment or similarly enclosed, the minimum distances
must be maintained. Do not cover the ventilation slot on the
projector. Heat build-up can reduce the service life of your
projector, and can also be dangerous.
SIDE and TOP
REAR
20cm
50cm
50cm
50cm
● Do not put any flammable object or spray can near the projector, hot air is exhausted from the ventilation
holes.
● If the projector is not to be used for an extended time, unplug the projector from the power outlet.
READ AND KEEP THIS USER'S GUIDE FOR LATER USE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION :
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USERSERVICEABLE PARTS INSIDE EXCEPT LAMP REPLACEMENT. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
THIS SYMBOL INDICATES THAT DANGEROUS
VOLTAGE CONSTITUTING A RISK OF ELECTRIC
SHOCK IS PRESENT WITHIN THIS UNIT.
2
THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT
OPERATING AND MAINTENANCE INSTRUCTIONS IN THE
USER'S GUIDE WITH THIS UNIT.
SAFETY INSTRUCTIONS
All the safety and operating instructions should be read before
the product is operated.
Read all of the instructions given here and retain them for later
use. Unplug this projector from AC power supply before
cleaning. Do not use liquid or aerosol cleaners. Use a damp
cloth for cleaning.
This projector should be operated only from the type of power
source indicated on the marking label. If you are not sure of
the type of power supplied, consult your authorized dealer or
local power company.
Follow all warnings and instructions marked on the projector.
Do not overload wall outlets and extension cords as this can
result in fire or electric shock. Do not allow anything to rest on
the power cord. Do not locate this projector where the cord
may be damaged by persons walking on it.
For added protection to the projector during a lightning storm,
or when it is left unattended and unused for long periods of
time, unplug it from the wall outlet. This will prevent damage
due to lightning and power line surges.
Do not attempt to service this projector yourself as opening or
removing covers may expose you to dangerous voltage or
other hazards. Refer all servicing to qualified service
personnel.
Do not expose this unit to rain or use near water... for
example, in a wet basement, near a swimming pool, etc...
Do not use attachments not recommended by the
manufacturer as they may cause hazards.
Do not place this projector on an unstable cart, stand, or table.
The projector may fall, causing serious injury to a child or
adult, and serious damage to the projector. Use only with a
cart or stand recommended by the manufacturer, or sold with
the projector. Wall or shelf mounting should follow the
manufacturer's instructions, and should use a mounting kit
approved by the manufacturers.
An appliance and cart combination should
be moved with care. Quick stops,
excessive force, and uneven surfaces
may cause the appliance and cart
combination to overturn.
Slots and openings in the back and bottom of the cabinet are
provided for ventilation, to insure reliable operation of the
equipment and to protect it from overheating.
Unplug this projector from wall outlet and refer servicing to
qualified service personnel under the following conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the projector.
c. If the projector has been exposed to rain or water.
d. If the projector does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions as improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the projector to normal operation.
e. If the projector has been dropped or the cabinet has been
damaged.
f. When the projector exhibits a distinct change in
performance-this indicates a need for service.
When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer that have the same characteristics as the
original part. Unauthorized substitutions may result in fire,
electric shock, or injury to persons.
Upon completion of any service or repairs to this projector, ask
the service technician to perform routine safety checks to
determine that the projector is in safe operating condition.
The openings should never be covered with cloth or other
materials, and the bottom opening should not be blocked by
placing the projector on a bed, sofa, rug, or other similar
surface. This projector should never be placed near or over a
radiator or heat register.
This projector should not be placed in a built-in installation
such as a book case unless proper ventilation is provided.
Never push objects of any kind into this projector through
cabinet slots as they may touch dangerous voltage points or
short out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the projector.
Voor de klanten in Nederland
Bij dit product zijn batterijen
geleverd.
Wanneer deze leeg zijn,
moet u ze niet weggooien
maar inleveren als KCA.
3
COMPLIANCES
Federal Communication Commission Notice
Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures :
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules.
Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such
changes or modifications should be made, you could be required to stop operation of the equipment.
Model Number
Trade Name
Responsible party
Address
Telephone No.
: CINEMA 20HD
: Boxlight
: BOXLIGHT
: 19332 Powder Hill Place Poulsbo, WA 98370-7407 USA
: (800)762-5757 or +1-360-779-7901
AC POWER CORD REQUIREMENT
The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.
AC Power Cord for the United States and Canada :
AC Power Cord used in the United States and Canada is listed by the Underwriters
Laboratories (UL) and certified by the Canadian Standard Association (CSA).
AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure that the
plug will fit into the power outlet. Do not try to defeat this safety feature. Should you be
unable to insert the plug into the outlet, contact your electrician.
GROUND
THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE.
4
TABLE OF CONTENTS
FEATURES AND DESIGN
PREPARATION
NAME OF EACH PART OF PROJECTOR
SETTING-UP PROJECTOR
CONNECTING AC POWER CORD
POSITIONING PROJECTOR
ADJUSTABLE FEET
MOVING PROJECTOR
6
7
7
8
8
9
10
10
CONNECTING PROJECTOR
11
TERMINALS OF PROJECTOR
CONNECTING TO COMPUTER
CONNECTING TO VIDEO EQUIPMENT
11
12
13
COMPUTER MODE
SELECTING INPUT SOURCE
SELECTING COMPUTER SYSTEM
PC ADJUSTMENT
AUTO PC ADJUSTMENT
MANUAL PC ADJUSTMENT
COMPATIBLE COMPUTER SPECIFICATIONS
PICTURE IMAGE ADJUSTMENT
IMAGE LEVEL SELECT
IMAGE LEVEL ADJUSTMENT
PICTURE SCREEN ADJUSTMENT
VIDEO MODE
SELECTING INPUT SOURCE
SELECTING VIDEO SYSTEM
PICTURE IMAGE ADJUSTMENT
IMAGE LEVEL SELECT
IMAGE LEVEL ADJUSTMENT
BEFORE OPERATION
OPERATION OF REMOTE CONTROL
LASER POINTER FUNCTION
REMOTE CONTROL BATTERIES INSTALLATION
TOP CONTROLS AND INDICATORS
OPERATING ON-SCREEN MENU
HOW TO OPERATE ON-SCREEN MENU
FLOW OF ON-SCREEN MENU OPERATION
MENU BAR
14
14
14
15
16
17
17
17
18
PICTURE SCREEN ADJUSTMENT
SETTING
SETTING MENU
APPENDIX
MAINTENANCE
BASIC OPERATION
TURNING ON / OFF PROJECTOR
ADJUSTING SCREEN
ZOOM ADJUSTMENT
FOCUS ADJUSTMENT
LENS SHIFT ADJUSTMENT
KEYSTONE ADJUSTMENT
PICTURE FREEZE FUNCTION
NO SHOW FUNCTION
SOUND ADJUSTMENT
19
19
20
20
20
20
20
21
21
22
22
22
23
23
24
26
27
27
28
30
31
31
32
33
33
34
36
37
37
39
39
WARNING TEMP. INDICATOR
AIR FILTER CARE AND CLEANING
CLEANING PROJECTION LENS
LAMP REPLACEMENT
LAMP REPLACE COUNTER
39
39
39
40
41
TROUBLESHOOTING
TECHNICAL SPECIFICATIONS
42
44
21
TRADEMARKS
● Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer,Inc.
● IBM and PS/2 are trademarks or registered trademarks of International Business Machines, Inc.
● Windows and PowerPoint are registered trademarks of Microsoft Corporation.
● Each name of corporations or products in the user's guide is a trademark or a registered trademark of its
respective corporation.
5
FEATURES AND DESIGN
This Multimedia Projector is designed with most advanced technology for portability, durability, and ease of use. This
projector utilizes built-in multimedia features, a palette of 16.77 million colors, and matrix liquid crystal display (LCD)
technology.
◆
Compact Design
This projector is extremely compact in size and weight.
It is designed to carry and work anywhere you wish to
use.
◆
Compatibility
This projector widely accepts various video and
computer input signals including;
● Computers
IBM-compatible or Macintosh computer up to 1280
x 1024 resolution.
● 6 Color Systems
NTSC, PAL, SECAM, NTSC 4.43, PAL-M or PALN color system can be connected.
◆
◆
Multi-Scan System
Motor-driven Lens Shift
Projection lens can be moved up and down with motordriven lens shift function. This function makes it easy to
provide projected image where you want.
Zoom and focus can be also adjusted with motor-driven
operation.
◆
Digital Zoom (for Computer)
Digital Zoom function adjusts image size to approx. 1/4 ~
49 times of original image size, allowing you to focus on
crucial information at a presentation.
◆
Keystone Correction
Positioning of the projector may result in distorted image
being displayed in a trapezoid shape. Keystone
Correction solves this problem by digitally altering
projection to produce undistorted images.
6
Multilanguage Menu Display
Operation menu is displayed in; English, German,
French, Italian, Spanish, Portuguese, Dutch, Swedish,
Chinese, Korean or Japanese.
Color management
You can make fine adjustments to the colors on the
screen to change them to the desired colors.
At this time, the colors are changed within an extremely
narrow hue range, so that other colors are not affected.
The luminance and gamma values can also be changed
in addition to the hue.
This allows colors to be reproduced with great accuracy.
Faithful color reproduction and color correction which
effectively matches colors to scenes or emphasizes colors can be achieved.
Adjustments can be made easily, because they are
reflected in the on-screen images in real time. Up to
eight colors can be adjusted at a single time. The adjustment data can be saved for images in both in video
mode and PC mode (total 8 images). The adjusted data
is displayed in a list for easy checking.
One-Touch Auto PC Adjustment
Incoming computer video signals are recognized and
best adjustment is automatically set by Auto PC
Adjustment. No complicated setup is necessary and
projection is always precise.
◆
Digital Visual Interface
This projector is equipped with DVI 24-pin terminal for
connecting DVI output from a computer.
● S-Video
S-Video signal, such as a S-VHS VCR output
signal, can be connected.
This projector has Multi-Scan System to conform to
almost all computer output signals quickly. There is no
need for troublesome manual adjustment of frequency
and other settings.
◆
◆
◆
High Resolution Image
Power Management
Power Management function is provided to reduce power
consumption while the projector is not in use.
This Power Management function operates to turn
Projection Lamp off when the projector detects signal
interruption and any button is not pressed over 5
minutes. Projection Lamp is automatically turned on
again when the projector detects signal or any operation
button is pressed.
This projector is shipped with this function ON.
● Component Video
Component video signal, such as a DVD player
output high definition TV signals including 480i,
480p, 575i, 575p, 720p, 1035i or 1080i, can be
connected.
This projector provides 1366 x 768 dots resolution for
computer input and 800 horizontal TV lines. Resolution
from a computer between XGA (1024 x 768) and SXGA
(1280 x 1024) is compressed into 1024 x 768 dots. This
projector cannot display image of over 1280 x 1024 dots.
When resolution of your computer is over than 1280 x
1024, reset the computer output for lower resolution.
◆
◆
◆
Auto Picture Control
The gamma value can be adjusted automatically in
accordance with the luminance of the screen. Images
that are either too dark or too bright can be adjusted to
the optimum level, so that these images can be reproduced without any distortion.
Equipped with an advanced Intelligent Digital Sharpness
Control which controls the sharpness automatically in
accordance with the images on the screen.
◆
Network connection (Optional)
Network connection is an optional product to control and
set up the projector via the network cable. By accessing
to the connected projector using the web browser on
your computer. It can be controlled and set up the
projector remotely. Contact the sales dealer where you
purchased this projector for optional parts.
PREPARATION
NAME OF EACH PART OF PROJECTOR
FRONT OF CABINET
TOP CONTROLS
AND INDICATORS
PROJECTION LENS
AIR INTAKE
VENT
LENS COVER
BACK OF CABINET
EXHAUST VENT
SPEAKERS
POWER CORD
CONNECTOR
INFRARED
REMOTE RECEIVER
TERMINALS
AND CONNECTORS
INFRARED
REMOTE RECEIVER
HOT AIR EXHAUSTED !
Air blown from exhaust vent is hot. When
using or installing the projector, following
precautions should be taken.
● Do not put a flammable object near this vent.
● Keep rear grills at least 3’(1 m) away from
any object, especially heat-sensitive object.
● Do not touch this area, especially screws
and metallic parts. This area will become
hot while the projector is used.
This projector detects internal temperature
and automatically controls operating power LAMP COVER
of Cooling Fans.
CARRYING
HANDLE
When attached the network connection to the
projector, remove the these parts.
BOTTOM OF CABINET
AIR INTAKE VENTS
This projector is equipped with cooling fans for protection from
overheating. Pay attention to following to ensure proper ventilation
and avoid a possible risk of fire and malfunction.
● Do not cover vent slots.
● Keep side clear of any objects. Obstructions may block cooling
air.
ADJUSTABLE FEET
AND
FEET LOCK LATCHES
7
PREPARATION
SETTING-UP PROJECTOR
CONNECTING AC POWER CORD
This projector uses nominal input voltages of 100-120 V or 200-240
V AC. This projector automatically selects correct input voltage. It
is designed to work with single-phase power systems having a
grounded neutral conductor. To reduce risk of electrical shock, do
not plug into any other type of power system.
Consult your authorized dealer or service station if you are not sure
of type of power supply being in use.
Connect the projector with a peripheral equipment before turning
the projector on. (Refer to pages 11 ~ 13 for connection.)
CAUTION
For safety, unplug AC Power Cord when an appliance is not
used.
When this projector is connected to outlet with AC Power Cord,
an appliance is in Stand-by Mode and consumes a little electric
power.
Connect AC Power Cord (supplied) to the
projector.
AC outlet must be near this equipment and must
be easily accessible.
NOTE ON POWER CORD
AC Power Cord must meet requirement of country where you use the projector.
Confirm AC plug type with chart below and proper AC power cord must be used.
If supplied AC Power Cord does not match AC outlet, contact your sales dealer.
AC Outlet side
Projector side
For U.S.A. and Canada
For Continental Europe
Ground
To POWER CORD
CONNECTOR on the
projector.
8
To AC Outlet.
(120 V AC)
To AC Outlet.
(200 - 240 V AC)
PREPARATION
POSITIONING PROJECTOR
● This projector is designed to project on a flat
projection surface.
● Projector can be focused from 5.0’ (1.5m) ~ 51.3’
(15.6m).
● Refer to figure below to adjust screen size.
ROOM LIGHT
Brightness in room has a great influence on
picture quality. It is recommended to limit
ambient lighting in order to provide best
image.
51.3’(15.6m)
38.4’(11.7m)
25.6’(7.8m)
308”
200”
100”
40”
400”
300”
12.7’(3.9m)
5.0’(1.5m)
Max. Zoom
231” Min. Zoom
154”
77”
31”
Screen
Size
Max. Zoom
40”
100”
150”
200”
250”
300”
400”
Min. Zoom
31”
77”
115”
154”
192”
231”
308”
5.0’ (1.5m)
12.7’ (3.9m)
19.1’ (5.8m)
25.6’ (7.8m)
32.0’ (9.8m)
38.4’ (11.7m)
51.3’ (15.6m)
Distance
LENS SHIFT ADJUSTMENT
Projection lens can be moved up and down with motor-driven lens shift function. This function makes it easy to
provide projected image where you want. Refer to P 20 for operation.
Highest Lens Shift
Lowest Lens Shift
H3
H1
H4
H2
H1 : H2 = 6 : 1
H3 : H4 = 1 : 1
NOTE
Screen size and lens shift ratio on the above charts are standard values and they may change by positioning
conditions.
9
PREPARATION
ADJUSTABLE FEET
Picture tilt and projection angle can be adjusted by
rotating ADJUSTABLE FEET. Projection angle can be
adjusted to 10.5 degrees.
1
Lift front of a projector and pull FEET LOCK LATCHES
on both sides of the projector.
2
Release FEET LOCK LATCHES to lock ADJUSTABLE
FEET and rotate ADJUSTABLE FEET to fine tune
position and tilt.
3
To shorten ADJUSTABLE FEET, lift front of the projector
and pull and undo FEET LOCK LATCHES.
Position and keystone distortion of image can be adjusted
using Menu Operation. (Refer to P 20 and 37.)
ADJUSTABLE FEET
NOTE :
FEET LOCK
LATCHES
THIS PROJECTOR SHOULD BE SET IN THE WAY
INDICATED. PROJECTION LAMP MAY MALFUNCTION.
MOVING PROJECTOR
Use Carry Handle when moving the Projector.
When moving the projector, replace lens cover and
retract feet to prevent damage to lens and cabinet.
When this projector is not in use for an extended period,
put it into case (dust cover) supplied with this projector.
CAUTION IN CARRYING OR TRANSPORTING THE PROJECTOR
● Do not drop or bump the projector, otherwise damages or malfunctions may result.
● When carrying the projector, use a suitable carrying case.
● Do not transport the projector by using a courier or transport service in an unsuitable transport case. This
may cause damage to the projector. To transport the projector through a courier or transport service,
consult your dealer for best way.
10
CONNECTING PROJECTOR
TERMINALS OF PROJECTOR
This projector has input and output terminals on its back for connecting computers and video equipment. Refer to figures on
pages 11 to 13 and connect properly.
COMPUTER AUDIO
INPUT (1 and 2) JACKS
Connect an audio output
(stereo) from computer to
these jacks.
(Refer to P12.)
COMPUTER INPUT
TERMINALS (DIGITAL/ANALOG)
Connect computer (digital/analog)
output to one of these terminals.
(Refer to P12.)
R/C JACK
INPUT 1
ANALOG
DIGITAL(DVI-D)
R/C JACK
CONTROL PORT
RESET
AUDIO 1
When using Wired/Wireless
Remote Control Unit as Wired
Remote Control, Connect
Wired Remote Control Unit to
this jack with Remote Control
Cable (supplied).
AUDIO 2
CONTROL PORT CONNECTOR
RESET BUTTON
This projector uses a micro processor
to control this unit, and occasionally,
this micro processor may malfunction
and need to be reset. This can be
done by pressing RESET button with a
pen, which will shut down and restart
unit. Do not use RESET function
excessively.
✽ Do not press this button. This button
is used for our optional accessories.
5 BNC INPUT JACKS
Connect component video
output (Y, Cb, Cr or Y, Pb, Pr)
from video equipment to
VIDEO/Y, Cb/Pb and Cr/Pr
jacks or connect computer
output {5 BNC Type (Green,
Blue, Red, Horiz. Sync and
Vert. Sync.)} from computer
to G, B, R, H/V and V jacks.
(Refer to P12 and 13.)
G
B
R
VIDEO/Y
Cb/Pb
H/V
V
Cr/Pr
INPUT 2
VIDEO/Y Cb/Pb
Cr/Pr
R–AUDIO–L
S–VIDEO
When controlling this projector
by computer, connect your
computer to this terminal.
(Refer to P12.)
(MONO)
INPUT 3
VIDEO INPUT JACKS
AUDIO INPUT JACKS
S-VIDEO INPUT JACK
Connect composite video
output from video equipment
to VIDEO/Y jack or connect
component video outputs to
VIDEO/Y, Cb/Pb and Cr/Pr
jacks. (Refer to P13.)
Connect an audio output
from video equipment to
these jacks.
(Refer to P13.)
Connect S-VIDEO
output from video
equipment to this
jack. (Refer to P13.)
11
CONNECTING PROJECTOR
CONNECTING TO COMPUTER
Cables used for connection
(✽ = Cable or adapter is not supplied with this projector.)
• VGA Cable (HDB 15 pin) ✽
• MAC Adapter (When connecting to Macintosh computer) ✽
• DVI-Digital Cable (for Single Link T.M.D.S.) ✽
• Audio Cable {Mini Plug (stereo) x 1} ✽
• BNC Cable ✽
• Control Cable for Serial Port
IBM-compatible computer or Macintosh computer (VGA / SVGA / XGA / SXGA)
Desktop type
Monitor Output
Monitor Output
BNC
Cable ✽
Audio Output
Serial port
Control Cable
for Serial Port
Audio
Cable ✽
(stereo)
DVI
Cable ✽
MAC Adapter ✽
Set slide switches
according to chart
below.
Laptop type
Terminal
VGA Cable ✽
COMPUTER
AUDIO IN 1 or 2
COMPUTER IN ANALOG
CONTROL
PORT
COMPUTER IN DIGITAL
INPUT 1
ANALOG
DIGITAL(DVI-D)
R/C JACK
CONTROL PORT
RESET
AUDIO 1
AUDIO 2
G
B
R
VIDEO/Y
Cb/Pb
H/V
V
Cr/Pr
INPUT 2
VIDEO/Y Cb/Pb
Cr/Pr
S–VIDEO
R–AUDIO–L
Terminals
of the Projector
(MONO)
INPUT 3
◆ MAC ADAPTER ✽
NOTE :
Set switches as shown in table
below depending on RESOLUTION MODE that you want to
use before you turn on projector and computer.
1
ON
13" MODE (640 x 480)
16" MODE (832 x 624) OFF
19" MODE (1024 x 768) OFF
21" MODE (1152 x 870) ON
12
2
ON
ON
ON
ON
When connecting cable, power cords of both
the projector and external equipment should
be disconnected from AC outlet. Turn the
projector and peripheral equipment on
before computer is switched on.
ON
ON
DIP
1 2 3 4 5 6
OFF
3
4
5
6
OFF OFF OFF OFF
OFF ON OFF OFF
ON OFF OFF OFF
ON ON OFF OFF
CONNECTING PROJECTOR
CONNECTING TO VIDEO EQUIPMENT
Cables used for connection
(✽ = Cable is not supplied with this projector.)
• Video Cable (RCA x 1), or (RCA x 3) ✽
• BNC Cable ✽
• S-VIDEO Cable
• Audio Cable (RCA x 2)
Video Source (example)
Video Cassette Recorder
Component video output equipment.
(such as DVD player or high-definition TV source.)
Video Disc Player
Composite Component Video Output Composite Component Video Output Audio Output
Video Output
(Y, Cb/Pb, Cr/Pr)
Video Output
(Y, Cb/Pb, Cr/Pr)
Video Cable
(RCA x 1)
Video Cable
(RCA x 3) ✽
Audio Cable
(RCA x 2)
BNC Cable ✽
VIDEO
Y - Cb/Pb - Cr/Pr VIDEO
Y - Cb/Pb - Cr/Pr AUDIO IN
S-VIDEO Output
S-VIDEO
Cable
S-VIDEO
INPUT 1
ANALOG
DIGITAL(DVI-D)
R/C JACK
CONTROL PORT
RESET
AUDIO 1
AUDIO 2
G
B
R
VIDEO/Y
Cb/Pb
H/V
V
Cr/Pr
INPUT 2
VIDEO/Y Cb/Pb
Cr/Pr
R–AUDIO–L
S–VIDEO
(MONO)
INPUT 3
Terminals
of the Projector
NOTE :
When connecting cable, power cords of
both the projector and external equipment
should be disconnected from AC outlet.
13
BEFORE OPERATION
OPERATION OF REMOTE CONTROL
Left Side
LENS SHIFT BUTTON
Used to select LENS
SHIFT function. (P20)
LENS SHIFT
ON-OFF
LENS KEYSTONE
KEYS
MENU
SCREEN
INPUT BUTTON
Used to select input
source. (P22)
UME
VOL
UME
VOL
LIGHT
MENU BUTTON
Used to select MENU
operation. (P17, 18)
SELECT
IMAGE
INPUT
IMAGE
INPUT
1
1
2
2
3
4
LIGHT SWITCH
Slide this switch, to illuminate key
on remote control unit for 10
seconds.
3
MUTE BUTTON
Z
ZOOM
MUTE
Z
F
NO SHOW
FREEZE
AUTO
F
AUTO PC ADJ. BUTTON
Used to operate AUTO PC
Adjustment function. (P23)
D
D.ZOOM
COLOR.M
POINT (VOLUME + / – )
BUTTONS
SELECT BUTTON
Used to select an item or
adjust value in ON-SCREEN
MENU. They are also used to
pan image in DIGITAL ZOOM
+/– mode. (P30)
POINT LEFT/RIGHT buttons
are also used as VOLUME +/–
buttons.
When pressing center of this
button, it works as SELECT
button.
FOCUS
Used to mute sound. (P21)
AUTO PC ADJ.
POWER ON-OFF BUTTON
Used to turn projector on or
off. (P19)
D
SELECT BUTTON
Used to execute item
selected. It is also used to
expand / compress image
in DIGITAL ZOOM mode.
(P30)
FREEZE BUTTON
Used to freeze picture.
(P21)
14
BEFORE OPERATION
Operating Range
LENS SHIFT
ON-OFF
LENS KEYSTONE
KEYSTONE BUTTON
KEYS
Used to correct
keystone distortion.
(P20, 37)
Used to select screen.
(P30, 36)
SCREEN
Point Remote Control Unit toward
projector (Receiver Window)
whenever pressing any button.
Maximum operating range for
Remote Control Unit is about 16.4’
(5m) and 60° in front and rear of the
projector.
UME
VOL
UME
VOL
MENU
SCREEN BUTTON
SELECT
IMAGE BUTTON
IMAGE
INPUT
IMAGE
INPUT
1
1
2
2
3
4
ZOOM BUTTON
Used to adjust zoom.
(P20)
3
Z
ZOOM
MUTE
NO SHOW BUTTON
Used to turn picture into
black image. (P21)
NO SHOW
Z
FREEZE
F
FOCUS
F
COLOR.M
16.4’
(5 m)
FOCUS BUTTON
Used to adjust focus.
(P20)
D
D.ZOOM
AUTO PC ADJ.
AUTO
60°
Used to select image
level. (P27, 33)
D
D.ZOOM BUTTON
Used to select DIGITAL
ZOOM +/– mode and
resize image. (P30)
16.4’
(5 m)
WIRED REMOTE JACK
When using as Wired
Remote Control, connect
Remote Control Cable to
this jack.
Battery installation is
required when using as
Wired Remote Control.
60°
COLOR MANAGEMENT
BUTTON
Used to operate COLOR
MANAGEMENT.
(P28, 34)
Remote Control Batteries Installation
1
Remove battery
compartment lid.
Pull up lid and
remove it.
2
Slide batteries into
compartment.
3
Replace compartment lid.
Two AA size batteries
For correct polarity (+ and
–), be sure battery
terminals are in contact
with pins in compartment.
To insure safe operation, please observe following precautions :
● Use (2) AA, UM3 or R06 type alkaline batteries.
● Replace two batteries at same time.
● Do not use a new battery with an used battery.
● Avoid contact with water or liquid.
● Do not expose Remote Control Unit to moisture, or heat.
● Do not drop Remote Control Unit.
● If a battery has leaked on Remote Control Unit, carefully wipe case clean and install new batteries.
● Danger of explosion if battery is incorrectly replaced.
● Dispose of used batteries according to batteries manufacturers instructions and local rules.
15
BEFORE OPERATION
TOP CONTROLS AND INDICATORS
This projector has CONTROL BUTTONS (TOP CONTROLS) and INDICATORS on its top.
LAMP REPLACE INDICATOR
WARNING TEMP. INDICATOR
READY INDICATOR
LAMP INDICATOR
Turns to yellow when
life of projection lamp
draws to an end. (P40)
Flashes red when
internal
projector
temperature is too
high. (P39)
Lights green when the
projector is ready to be
turned on.
And it
flashes green in Power
Management mode.
(P37)
Becomes dim when the
projector is turned on.
And bright when the
projector is in stand-by
mode.
POWER ON–OFF BUTTON
Used to turn the projector
on or off. (P19)
MENU BUTTON
Used to open or close
MENU operation. (P17,
18)
INPUT BUTTON
Used to select input
source. (P22)
ZOOM BUTTON
Used to adjust zoom.
(P20)
FOCUS BUTTON
Used to adjust focus.
(P20)
AUTO PC ADJ. BUTTON
LENS SHIFT BUTTON
Used to operate AUTO PC
Adjustment function. (P23)
Used to select LENS
SHIFT function. (P20)
IMAGE BUTTON
POINT (VOLUME + / – ) BUTTONS
Used to select an item or adjust
value in ON-SCREEN MENU. They
are also used to pan image in
DIGITAL ZOOM +/– mode. (P30)
POINT LEFT/RIGHT buttons are
also used as VOLUME +/– buttons.
16
SELECT BUTTON
Used to execute item
selected. It is also used
to expand / compress
image in DIGITAL
ZOOM mode. (P30)
Used to select image
level. (P27, 33)
BEFORE OPERATION
OPERATING ON-SCREEN MENU
HOW TO OPERATE ON-SCREEN MENU
You can control and adjust this projector through ON-SCREEN
MENU. Refer to following pages to operate each adjustment on
ON-SCREEN MENU.
WIRELESS REMOTE CONTROL
POINT BUTTON
Used to move Pointer
UP/ DOWN/ RIGHT/
LEFT.
1 DISPLAY MENU
Press MENU button to display ON-SCREEN MENU.
2 MOVING POINTER
Move pointer (✽ see below) or adjust value of item by pressing
POINT button(s) on Top Control or on Remote Control Unit.
✽ Pointer is icon on ON-SCREEN MENU to select item. See figures on section "FLOW OF ON-SCREEN MENU OPERATION"
below.
SELECT BUTTON
Center of point button
used to select item.
TOP CONTROL
POINT BUTTONS
Used to move Pointer
UP/ DOWN/ RIGHT/
LEFT.
3 SELECT ITEM
Select item or set selected function by pressing SELECT button.
SELECT BUTTON
Used to select item.
FLOW OF ON-SCREEN MENU OPERATION
Display ON-SCREEN MENU
1
Press MENU button to display ON-SCREEN MENU (MENU
BAR). A red frame is POINTER.
Select Menu to be adjusted
2
MENU ICON
MENU BAR
POINTER (red frame)
Press POINT DOWN button to
move POINTER.
POINTER
(red frame)
Move POINTER (red frame) to MENU ICON that you want to
select by pressing POINT RIGHT / LEFT buttons.
ITEM
Control or adjust item through ON-SCREEN MENU
3
Press POINT DOWN button and move POINTER (red frame
or red arrow) to ITEM that you want to adjust, and then press
SELECT button to show ITEM DATA.
4
Adjust ITEM DATA by pressing POINT RIGHT / LEFT
buttons.
Refer to following pages for details of respective
adjustments.
SELECT
BUTTON
32
32
Mid
32
32
ITEM DATA
Press POINT LEFT/RIGHT
buttons to adjust value or
set function.
32
17
BEFORE OPERATION
MENU BAR
FOR PC SOURCE
Press MENU BUTTON while connecting to PC input source.
IMAGE SELECT MENU
SCREEN MENU
SETTING MENU
Used to adjust size
of image. [Normal
/ Full / True / Digital
zoom +/–]
(Refer to P30)
Used to change
settings of projector
or reset Lamp
Replace Counter.
(Refer to P37, 38)
GUIDE WINDOW
PC SYSTEM MENU
Shows selected
item of ONSCREEN MENU.
Used to select
computer system.
(Refer to P22, 23)
Used to select
image level among
Standard, Real
and Image 1 ~ 4.
(Refer to P27)
INPUT MENU
PC ADJUST MENU
IMAGE ADJUST MENU
SOUND MENU
Used to select
input source (Input
1, Input 2 or Input
3). (Refer to P22)
Used to adjust
parameters to
match with input
signal format.
(Refer to P23-25)
Used to adjust computer
image.
[Contrast / Brightness
/ Color temp.
/ White Balance (R/G/B)
/ Color management
/ Auto picture control
/ Gamma]
(Refer to P28-29)
Used to adjust
volume or mute
sound.
(Refer to P21)
FOR VIDEO SOURCE
Press MENU BUTTON while connecting to VIDEO input source.
INPUT MENU
IMAGE SELECT MENU
Used to select
input source
(Input 1, Input 2
or Input 3).
(Refer to P31)
Used to select image
level among
Standard, Cinema
and Image 1 ~ 4.
(Refer to P33)
Same function as
Menu for PC source.
AV SYSTEM MENU
Used to select
system of selected
video source.
(Refer to P32)
Used to set size of
image to Full, Zoom,
Normal or Wide zoom.
(Refer to P36)
IMAGE ADJUST MENU
Used to adjust picture image.
[Contrast / Brightness / Color
/ Tint / Color management
/ Auto picture control / Color temp.
/ White balance (R/G/B)
/ Sharpness / Gamma / Noise
Reduction / Progressive]
(Refer to P34-36)
18
SCREEN MENU
Same function as
Menu for PC source.
BEFORE OPERATION
TURNING ON / OFF PROJECTOR
TURNING ON PROJECTOR
1
Complete peripheral connections (with Computer, VCR, etc.)
before turning on projector. (Refer to "CONNECTING TO
PROJECTOR" on pages 11~13 for connecting that equipment.)
2
Connect the projector's AC Power Cord into an AC outlet. LAMP
Indicator lights RED, and READY Indicator lights GREEN.
Input position
Input 1
30
NOTE : When “On start” function is ON, this projector is turned
on automatically by connecting AC Power Cord to an
AC outlet. (Refer to pages 37, 38.)
3
Press POWER ON-OFF button on Top Control or on Remote
Control Unit to ON. LAMP Indicator dims, and Cooling Fans
start to operate. Preparation Display appears on a screen and
count-down starts. Signal from PC or Video source appears after
30 seconds.
Current Input position is also displayed on screen for 5 seconds.
Preparation Display disappears after 30 seconds.
TURNING OFF PROJECTOR
1
Press POWER ON-OFF button on Top Control or on Remote
Control Unit, and a message "Power off?" appears on a screen.
2
Press POWER ON-OFF button again to turn off projector. LAMP
Indicator lights bright and READY Indicator turns off. After
projector is turned off, Cooling Fans operate (for 90 seconds).
During this "Cooling Down" period, this appliance cannot be
turned on.
3
When projector has cooled down, READY Indicator lights
GREEN again and you can turn projector on. After cooling down
completely, disconnect AC Power Cord.
Power off?
Message disappears after 4 seconds.
TO MAINTAIN LIFE OF LAMP, ONCE YOU TURN
PROJECTOR ON, WAIT AT LEAST 5 MINUTES BEFORE
TURNING IT OFF.
When “Power Management” function is ON, projector detects signal interruption and turns off Projection Lamp automatically.
Refer to “Power Management” on page 37.
When WARNING TEMP. Indicator flashes red, projector is automatically turned off. Wait at least 5 minutes before turning on
projector again.
When WARNING TEMP. Indicator continues to flash, follow procedures below:
1. Press POWER ON-OFF button to turn the projector off and disconnect AC Power Cord from an AC outlet.
2. Check Air Filters for dust accumulation.
3. Clean Air Filters. (See "AIR FILTER CARE AND CLEANING" section on page 39.)
4. Turn the projector on again.
If WARNING TEMP. Indicator should still continue to flash, call Boxlight Corporation at 1-800-762-5757 or 360-779-7901.
19
BASIC OPERATION
ADJUSTING SCREEN
ZOOM ADJUSTMENT
1
Press ZOOM button on Top Control or ZOOM ▲/▼ button on
Remote Control Unit. Message “Zoom” is displayed.
2
Press ZOOM ▲ button or POINT UP button to make image
larger, and press ZOOM ▼ button or POINT DOWN button to
make image smaller.
Zoom
Message disappears after 4 seconds.
FOCUS ADJUSTMENT
1
Press FOCUS button on Top Control or FOCUS ▲/▼ button on
Remote Control Unit. Message “Focus” is displayed.
2
Adjust focus of image by pressing FOCUS ▲/▼ button or
POINT UP/DOWN button(s) .
NOTE;
Focus adjustment may not function properly if the image is
corrected by KEYSTONE adjustment.
Focus
Message disappears after 4 seconds.
LENS SHIFT ADJUSTMENT
1
Press LENS SHIFT button on Top Control or on Remote Control
Unit. Message “Lens shift” is displayed.
2
Press POINT UP button to move image up, press POINT DOWN
button to move image down.
Lens shift
KEYSTONE ADJUSTMENT
If the projected picture has keystone distortion, correct the image with KEYSTONE adjustment.
1
Press KEYSTONE button on Remote Control Unit or select
Keystone on SETTING menu. (Refer to page 37.) Keystone
dialog box appears.
2
Correct keystone distortion by pressing POINT
UP/DOWN/LEFT/RIGHT button(s). Press POINT UP button to
reduce the upper part of the image, and press POINT DOWN
button to reduce the lower part. Press POINT LEFT button to
reduce the left part, and press POINT RIGHT button to reduce
the right part.
Reduce the upper width
with POINT UP button.
20
Reduce the lower width
with POINT DOWN button.
• Arrows are white in no correction.
• Arrow(s) of direction being corrected turn(s) red.
• Arrow(s) disappear(s) at the maximum
correction.
• If you press the KEYSTONE button on the
remote control unit once more while the
keystone dialog box is being displayed, the
keystone adjustment will be canceled.
Reduce the left part with
POINT LEFT button.
Reduce the right part with
POINT RIGHT button.
BASIC OPERATION
PICTURE FREEZE FUNCTION
Press FREEZE button on Remote Control Unit to freeze picture on-screen. To cancel FREEZE function, press FREEZE
button again or press any other button except POINT / SELECT button.
NO SHOW FUNCTION
Press NO SHOW button on Remote Control Unit to black out image.
To restore to normal, press NO SHOW button again or press any
other button except POINT / SELECT button.
No show
Message disappears after 4 seconds.
SOUND ADJUSTMENT
Indicates roughly level of
volume.
DIRECT OPERATION
Volume
Press VOLUME (+/–) button(s) on Top Control or on Remote Control
Unit to adjust volume. Volume dialog box appears on screen for a few
seconds.
(+) button to increase volume, and (–) button for decreasing.
Mute
Press MUTE button on Remote Control Unit to cut off sound. To
restore sound to its previous level, press MUTE button again or press
Volume (+/–) button(s).
Press MUTE button to set
Mute function On or Off.
Display disappears after 4 seconds.
MENU OPERATION
1
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT buttons to move the red frame pointer to
SOUND Menu icon.
2
Press POINT DOWN button to move the red frame pointer to
item that you want to select, and then press SELECT button.
SOUND MENU
SOUND Menu icon
Indicates roughly
level of volume.
Volume
To increase volume, press POINT RIGHT button, and press POINT
LEFT button for decreasing.
Close SOUND Menu.
Mute
Press POINT LEFT/RIGHT button(s) to cut off sound. Dialog box
display is changed to “On” and sound is cut off. To restore sound to
its previous level, press POINT LEFT/RIGHT button(s) again.
21
COMPUTER INPUT
SELECTING INPUT SOURCE
DIRECT OPERATION
INPUT button
Choose Input by pressing INPUT button on Top Control.
Choose Input by pressing INPUT, INPUT 1, INPUT 2 or INPUT 3
button on Remote Control Unit.
If projector cannot reproduce proper image, select correct input source
through MENU OPERATION (see below).
INPUT 1
INPUT 2
INPUT 3
MENU OPERATION
1
2
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT buttons to select Input and press SELECT
button. Another dialog box INPUT SELECT Menu will appear.
INPUT Menu icon
Press POINT DOWN button and the red-arrow icon will appear.
Move arrow to INPUT source that you want to select, and then
press SELECT button.
SELECTING COMPUTER SYSTEM
WHEN SELECT INPUT 1 (COMPUTER INPUT TERMINALS )
1
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button to move the red frame pointer to
INPUT Menu icon.
2
Press POINT DOWN button to move the red arrow pointer to
Input 1 and then press SELECT button. Source Select Menu will
appear.
3
Move the pointer to either Digital or Analog and then press
SELECT button.
INPUT MENU
INPUT Menu icon
Move the pointer (red arrow)
to Input 1 and press SELECT
button.
Input 1
Source Select Menu
Digital
When your computer is connected to COMPUTER
INPUT (DIGITAL) terminal, select RGB (Digital).
Analog
When your computer is connected to COMPUTER INPUT
(ANALOG) terminal, select RGB (Analog).
Move the pointer to Digital or
Analog and press SELECT
button.
WHEN SELECT INPUT 2 (5 BNC INPUT JACKS )
When connect the computer output [5 BNC Type (Green, Blue, Red,
Horiz. Sync and Vert. Sync.)] from the computer to G, B, R, H/HV and V
jacks.
INPUT MENU
INPUT Menu icon
1
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button to move the red frame pointer to
INPUT Menu icon.
2
Press POINT DOWN button to move the red arrow pointer to
Input 2 and then press SELECT button. Source Select Menu will
appear.
3
Press POINT DOWN button and the red-arrow icon will appear.
Move arrow to "RGB", and then press SELECT button.
Move the pointer (red arrow)
to Input 2 and press SELECT
button.
Input 2
Source Select Menu
22
Move the pointer to RGB
and press SELECT button.
COMPUTER INPUT
AUTOMATIC MULTI-SCAN SYSTEM
This projector automatically tunes to most different types of computers based on VGA, SVGA, XGA or SXGA (refer to
“COMPATIBLE COMPUTER SPECIFICATION” on page 26). When selecting Computer, this projector automatically tunes
to incoming signal and projects proper image without any special setting. (Some computers need setting manually.)
Note : Projector may display one of following messages.
Auto
––––
When projector cannot recognize connected signal as PC
system provided in this projector, Auto PC Adjustment
function operates to adjust projector and message “Auto”
is displayed on SYSTEM Menu icon.
When image is not provided properly, manual adjustment
is required. (Refer to P24 and 25.)
PC SYSTEM MENU
PC SYSTEM Menu icon
Displays system being
selected.
There is no signal input from computer. Make sure
connection of computer and the projector is set correctly.
(Refer to TROUBLESHOOTING on page 42.)
D-VGA, D-SVGA or D-XGA
When digital computer signal is received on DVI terminal,
above message is displayed on PC SYSTEM Menu icon.
SELECT COMPUTER SYSTEM MANUALLY
PC SYSTEM MENU
This projector automatically selects PC system among those provided
in this projector and PC system can be also selected manually.
1
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT buttons to move the red frame pointer to
PC SYSTEM Menu icon.
2
Press POINT DOWN button to move the red arrow pointer to
system that you want to set, and then press SELECT button.
PC SYSTEM Menu icon
Displays system being selected.
Systems on this dialog box can
be selected.
Custom Mode (1~5) set in PC
ADJUST Menu. (P24, 25)
PC ADJUSTMENT
AUTO PC ADJUSTMENT
Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots and Picture Position to conform to your
computer. Auto PC Adjustment function can be operated as follows.
Auto PC Adj.
1
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button to move the red frame pointer to PC
ADJUST Menu icon.
2
Press POINT DOWN button to move the red frame pointer to
AUTO PC Adj. icon and then press SELECT button twice.
This Auto PC Adjustment can be also executed by pressing
AUTO PC ADJ. button on Top Control or on Remote Control
Unit.
Store adjustment parameters.
Adjustment parameters from Auto PC Adjustment can be memorized
in this projector. Once parameters are memorized, setting can be
done just by selecting Mode in PC SYSTEM Menu (P23). Refer to
step 3 of MANUAL PC ADJUSTMENT section (P25).
PC ADJUST MENU
PC ADJUST Menu icon
Move the red frame pointer to AUTO PC
Adj. icon and press SELECT button.
NOTE
● Fine sync, Total dots and Picture Position of some computers can not be fully adjusted with this Auto PC Adjustment
function. When image is not provided properly through this function, manual adjustments are required. (Refer to page 24,
25.)
● Auto PC Adjustment function cannot be operated in Digital Signal input on DVI terminal and “RGB”, “720p (HDTV)”,
“1035i (HDTV)” or “1080i (HDTV)” is selected on PC SYSTEM Menu.
23
COMPUTER INPUT
MANUAL PC ADJUSTMENT
This projector can automatically tune to display signals from most personal computers currently distributed. However, some
computers employ special signal formats which are different from standard ones and may not be tuned by Multi-Scan system
of this projector. If this happens, projector cannot reproduce a proper image and image may be recognized as a flickering
picture, a non-synchronized picture, a non-centered picture or a skewed picture.
This projector has a Manual PC Adjustment to enable you to precisely adjust several parameters to match with those special
signal formats. This projector has 5 independent memory areas to memorize those parameters manually adjusted. This
enables you to recall setting for a specific computer whenever you use it.
Note : This PC ADJUST Menu cannot be operated when in digital signal input on DVI terminal and “RGB” is selected on PC
SYSTEM MENU (P23).
1
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button to move the red frame pointer to PC
ADJUST Menu icon.
2
Press POINT DOWN button to move the red frame pointer to
item that you want to adjust and then press SELECT button.
Adjustment dialog box will appear. Press POINT LEFT/RIGHT
button to adjust value.
Fine sync
PC ADJUST MENU
PC ADJUST Menu icon
Move the red frame icon to item and press
SELECT button.
Adjusts an image as necessary to eliminate flicker from display.
Press POINT LEFT/RIGHT button to adjust value.(From 0 to 31.)
Total dots
Number of total dots in one horizontal period. Press POINT
LEFT/RIGHT button(s) and adjust number to match your PC image.
Selected Mode
Shows status
(Stored / Free) of
selected Mode.
Horizontal
Adjusts horizontal picture position. Press POINT LEFT/RIGHT
button(s) to adjust position.
Vertical
Adjusts vertical picture position. Press POINT LEFT/RIGHT
button(s) to adjust position.
Press POINT LEFT/RIGHT
button to adjust value.
Press SELECT button at this icon to
adjust “Clamp,” “Display area (H/V)” or
set “Full screen.”
Current mode
Press SELECT button to show information of computer selected.
Clamp
Current mode
Adjusts clamp position. When image has a dark bar(s), try this
adjustment.
Press SELECT button at
Current mode icon to show
information of computer
connected.
24
COMPUTER INPUT
Display area
Selects area displayed with this projector. Select resolution at
Display area dialog box.
Press SELECT button at
Display area icon and Display
area dialog box appears.
Display area H
Adjustment of horizontal area displayed with this projector. Press
POINT LEFT/RIGHT button(s) to decrease/increase value and then
press SELECT button.
Display area
Display area V
Adjustment of vertical area displayed with this projector. Press
POINT LEFT/RIGHT button(s) to decrease/increase value and then
press SELECT button.
Full screen
Press POINT LEFT
/RIGHT button(s) to
adjust value and then
press SELECT button.
Press POINT LEFT/RIGHT button(s) to switch Full screen function to
“On” or “Off.” Set “On” to resize image to fit the horizontal size of
the screen.
NOTE : Display area (H/V) and Full screen cannot be adjusted when
“1035i (HDTV)” or “1080i (HDTV)” is selected on PC
SYSTEM Menu (P23).
3
To store adjustment data.
This Mode has parameters being stored.
Store
To store adjustment parameters, move the red frame pointer to
Store icon and then press SELECT button. Move the red arrow
pointer to any of Mode 1 to 5 that you want to store and then
press SELECT button.
Mode free
To clear adjustment parameters previously set, move the red
frame pointer to Mode free icon and then SELECT button. Move
the red arrow pointer to Mode that you want to clear and then
press SELECT button.
Other icons operates as follows.
Vacant Mode
Shows values of “Total dots,”
“Horizontal,” “Vertical,” “Display
area H,” and “Display area V.”
Store icon
Reset
Reset all adjust parameters on adjustment dialog box to previous
figure.
To clear adjustment data.
Quit
Closes PC ADJUST MENU.
Close this dialog box.
Mode free icon
25
COMPUTER INPUT
COMPATIBLE COMPUTER SPECIFICATIONS
Basically this projector can accept a signal from all computers with V, H-Frequency mentioned below and less
than 140 MHz of Dot Clock.
ON-SCREEN
DISPLAY
VGA 1
VGA 2
VGA 3
VGA 4
VGA 5
VGA 6
VGA 7
MAC LC13
MAC 13
RGB
RGB
SVGA 1
SVGA 2
SVGA 3
SVGA 4
SVGA 5
SVGA 6
SVGA 7
SVGA 8
SVGA 9
SVGA 10
SVGA 11
MAC 16
XGA 1
XGA 2
XGA 3
XGA 4
XGA 5
XGA 6
XGA 7
XGA 8
XGA 9
RESOLUTION
640 x 480
720 x 400
640 x 400
640 x 480
640 x 480
640 x 480
640 x 480
640 x 480
640 x 480
––––––––
(Interlace)
––––––––
(Interlace)
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
832 x 624
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
(Interlace)
H-Freq.
(kHz)
V-Freq.
(Hz)
ON-SCREEN
DISPLAY
31.47
31.47
31.47
37.86
37.86
37.50
43.269
34.97
35.00
15.734
15.625
35.156
37.88
46.875
53.674
48.08
37.90
34.50
38.00
38.60
32.70
38.00
49.72
48.36
68.677
60.023
56.47
60.31
48.50
44.00
63.48
36.00
59.88
70.09
70.09
74.38
72.81
75.00
85.00
66.60
66.67
30
25
56.25
60.32
75.00
85.06
72.19
61.03
55.38
60.51
60.31
51.09
60.51
74.55
60.00
84.997
75.03
70.07
74.92
60.02
54.58
79.35
43.59
XGA 10
XGA 11
XGA 12
XGA 13
XGA 14
XGA15
MAC 19
MAC 21
SXGA 1
SXGA 2
SXGA 3
SXGA 4
SXGA 5
SXGA 6
SXGA 7
SXGA 8
SXGA 9
SXGA 10
SXGA 11
SXGA 12
SXGA 13
SXGA 14
SXGA 15
SXGA 16
SXGA 17
SXGA 18
SXGA 19
MAC
MAC
RESOLUTION
1024 x 768
1024 x 768
1024 x 768
(Interlace)
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1152 x 870
1152 x 864
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 960
1152 x 900
1152 x 900
1280 x 1024
(Interlace)
1280 x 1024
(Interlace)
1280 x 1024
1280 x 1024
1152 x 900
1280 x 1024
(Interlace)
1280 x 1024
1280 x 960
1280 x 1024
1035i (HDTV)
––––––––
(Progressive)
––––––––
(Interlace)
1080i (HDTV)
––––––––
(Interlace)
720p (HDTV)
H-Freq.
(kHz)
V-Freq.
(Hz)
62.04
61.00
35.522
46.90
47.00
58.03
60.24
68.68
64.20
62.50
63.90
63.34
63.74
71.69
81.13
63.98
79.976
60.00
61.20
71.40
50.00
50.00
63.37
76.97
61.85
46.43
63.79
75.00
80.00
45.00
33.75
33.75
77.07
75.70
43.48
58.20
58.30
72.0
75.08
75.06
70.40
58.60
60.00
59.98
60.01
67.19
76.107
60.02
75.025
60.00
65.20
75.60
43.00
47.00
60.01
72.00
66.00
43.35
60.18
75.08
75.08
60.00
30.00
30.00
When a input signal is digital from DVI terminal, refer to chart below.
ON-SCREEN
DISPLAY
RESOLUTION
H-Freq.
(kHz)
V-Freq.
(Hz)
ON-SCREEN
DISPLAY
RESOLUTION
H-Freq.
(kHz)
V-Freq.
(Hz)
D-VGA
D-SVGA
640 x 480
800 x 600
31.469
37.879
59.940
60.317
D-XGA
1024 x 768
48.363
60.004
NOTE : Specifications are subject to change without notice.
26
COMPUTER INPUT
PICTURE IMAGE ADJUSTMENTS
IMAGE LEVEL SELECT (DIRECT)
Select image level among Standard, Real, Image 1, Image 2, Image 3
and Image 4 by pressing IMAGE button on Top Control or on Remote
Control Unit.
Select Image 1-4 by pressing IMAGE 1-4 buttons on Remote Control
Unit.
IMAGE button
Standard
Real
Image 1
Standard
Normal picture level preset on this projector.
Image 2
Real
Picture level with improved halftone for graphics.
Image 3
IMAGE 1~4
User preset picture adjustment in IMAGE ADJUST Menu (P28-29).
Image 4
IMAGE LEVEL SELECT (MENU)
1
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button to move the red frame pointer to
IMAGE SELECT Menu icon.
2
Press POINT DOWN button to move the red frame pointer to
level that you want to set and then press SELECT button.
IMAGE SELECT MENU
IMAGE SELECT
Menu icon
Standard
Normal picture level preset on this projector.
Real
Move the red frame icon to level
and press SELECT button.
Picture level with improved halftone for graphics.
IMAGE 1~4
Level being selected.
User preset picture adjustment in IMAGE ADJUST Menu (P28-29).
27
COMPUTER INPUT
IMAGE LEVEL ADJUSTMENT
1
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT buttons to move the red frame pointer to
IMAGE ADJUST Menu icon.
2
Press POINT DOWN button to move the red frame pointer to
item that you want to adjust and then press SELECT button.
Level of each item is displayed. Adjust each level by pressing
POINT LEFT/RIGHT button(s).
IMAGE ADJUST MENU
Move the red frame pointer to
item to be selected and then
press SELECT button.
IMAGE ADJUST
Menu icon
Contrast
Press POINT LEFT button to decrease contrast, and POINT RIGHT
button to increase contrast. (From 0 to 63.)
Brightness
Press POINT LEFT button to adjust image darker, and POINT
RIGHT button to adjust brighter. (From 0 to 63.)
Selected Image level
Color temp.
Press either POINT LEFT button or POINT RIGHT button to Color
temp. level that you want to select. (XLow, Low, Mid or High)
White balance (Red)
32
Press POINT LEFT button to lighten red tone and POINT RIGHT
button to deeper tone. (From 0 to 63.)
32
Mid
White balance (Green)
32
Press POINT LEFT button to lighten green tone and POINT RIGHT
button to deeper tone. (From 0 to 63.)
32
32
White balance (Blue)
Press POINT LEFT button to lighten blue tone and POINT RIGHT
button to deeper tone. (From 0 to 63.)
L1
Color Management
8
The Color management function can be used to adjust the level,
phase and gamma of the selected display colors on the screen, and
to replace these colors with other colors if required.
The projector lets you replace up to eight colors for each image.
There are four preset images for VIDEO mode and four preset
images for PC, giving a total of eight images.
1
Press the POINT DOWN button to move the red frame pointer to
"COLOR MANAGEMENT", and then press the SELECT button.
The COLOR MANAGEMENT menu will appear and pointer
mode will be enabled. The image that was being projected when
the button was pressed will be paused, and the COLOR MANAGEMENT POINTER will appear.
2
Use the POINT buttons to move the pointer to a section of the
paused image that contains the color that you would like to
adjust, and then press the SELECT button. The mode will
change to COLOR SELECTION mode, and the color in the center of the pointer will be selected and adjustment will be possible.
3
28
Use the POINT buttons to adjust the level and phase of the
color, and then press the SELECT button to confirm the setting.
Next, use the POINT buttons to adjust the gamma correction for
the color, and then press the SELECT button to accept the setting. When the SELECT button is pressed, the mode will change
to LIST mode.
Press POINT LEFT/RIGHT buttons
to adjust value.
Store icon
Press SELECT button at this icon to
store adjustment.
POINTER MODE
COLOR
MANAGEMENT
POINTER
NOTE;
Press the COLOR M. button on the remote control to display the COLOR MANAGEMENT menu.
If you would like to check or re-adjust a color
management setting that has already been made,
press the COLOR M. button on the remote control
once more to change to LIST mode.
VIDEO INPUT
4
To move the red frame pointer to "MENU", and then press the
SELECT button. The message "OK"? is displayed. Move the
pointer to [Yes] and then press SELECT button. The COLOR
MANAGEMENT menu will be exited and the display will return
to the IMAGE ADJUST menu. (At this time, the image will stop
being paused and normal projection will resume.) After changing the COLOR MANAGEMENT settings, use the IMAGE
ADJUST menu to store the changed settings.
COLOR SELECTION
MODE
Level and phase
adjustment palette.
Gamma
adjustment palette.
COLOR SELECTION MODE
CANCEL
The mode will return to the pointer mode (even if you press the
MENU key on the projector or the remote control). (You will need to
reselect and re-adjust the color in this case.)
QUIT
The COLOR MANAGEMENT menu will be exited and the display will
return to the normal projection screen, but any settings that have
been changed will not be stored. To store the changed settings, be
sure to select "LIST" using the POINT buttons and change to the
next mode (LIST mode).
LIST
LIST MODE
CANCEL
QUIT
COLOR PALETTE
DEL
LIST MODE
The check mark will be cleared and the effect of the setting adjustment
for that line on the projected images will be momentarily canceled.
COLOR PALETTE
The mode will return to COLOR SELECTION mode so that you can
re-adjust the setting for the color in that line. This option is not available if the check mark has been cleared by the operation immediately above.)
DEL
The setting adjustment for the color in that line will be canceled.
ALL DEL
The setting adjustment for the colors in all lines will be canceled.
COLOR M.
The mode will return to POINTER mode.
Auto picture control
Press either POINT LEFT button or POINT RIGHT button to Auto
picture control position that you want to select . (Off, L1 or L2)
Off ······· Auto picture control OFF position.
L1 ········ Auto picture control LEVEL 1 position.
L2 ········ Auto picture control LEVEL 2 position.
Gamma
Press either POINT LEFT button or POINT RIGHT button to obtain
better balance of contrast. (From 0 to 15.)
Store
To store manually preset image, move the red frame pointer to Store
icon and press SELECT button. Image Level Menu will appear.
Move the red frame pointer to Image 1 to 4 where you want to set
and then press SELECT button.
Other icons operates as follows.
ALL DEL
COLOR M.
NOTE;
If you press the COLOR M. button on the remote
control, the COLOR MANAGEMENT menu will be
exited and the display will return to the normal
projection screen, but any settings that have been
changed will not be stored. To store the changed
settings, be sure to select "MENU" using the
POINT buttons and store the settings.
32
32
Mid
32
32
32
L1
8
Reset
MENU
Image Level Menu
Move the red frame pointer to
any of Image 1 to 4 where you
want to set and then press
SELECT button.
Reset all adjustment to previous figure.
Quit
Closes IMAGE MENU.
29
COMPUTER INPUT
PICTURE SCREEN ADJUSTMENT
This projector has a picture screen resize function, which enables you to display desirable image size.
PICTURE SCREEN SELECT (DIRECT)
SCREEN button
Select picture screen among Normal, Full, True, Digital zoom + and
Digital zoom - by pressing SCREEN button on Remote Control Unit.
Normal
Full
True
Digital zoom +
Digital zoom -
PICTURE SCREEN SELECT (MENU)
1
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button(s) to move the red frame pointer to
SCREEN Menu icon.
2
Press POINT DOWN button and move the red frame pointer to
function that you want to select and then press SELECT button.
SCREEN MENU
SCREEN Menu icon
Move red frame to function and press
SELECT button.
Normal
Provides image to fit the panel size of the screen.
Full
Provides image to fit the horizontal size of the screen.
True
Provides image in its original size. When the original image size is
larger than screen size (1366 x 768), this projector enters “Digital
Zoom +” mode automatically.
Digital zoom +
When Digital zoom + is selected, ON-SCREEN MENU disappears
and message “D. Zoom +” is displayed. Press SELECT button to
expand image size. And press POINT UP/DOWN/LEFT/RIGHT
button(s) to pan image. Panning function can work only when image
is larger than screen size.
The projected image can be also expanded by pressing D.ZOOM ▲
button on Remote Control Unit.
Digital Zoom –
When Digital zoom – is selected, ON-SCREEN MENU disappears
and message “D. Zoom –” is displayed. Press SELECT button to
compress image size.
The projected image can be also compressed by pressing D.ZOOM
▼ button on Remote Control Unit.
To cancel Digital Zoom +/– mode, press any button except D.ZOOM
▲/▼, SELECT, POINT and AUTO PC ADJ. buttons.
30
NOTE
● True and Digital zoom +/– cannot be operated
when “RGB”, “1035i (HDTV)” or “1080i (HDTV)” is
selected on PC SYSTEM Menu (P23).
● Full cannot be selected when “720p (HDTV)”,
“1035i (HDTV)” or “1080i (HDTV)” is selected on
PC SYSTEM Menu (P23).
● This projector cannot display any resolution higher
than 1280 X 1024. If your computer’s screen
resolution is higher than 1280 X 1024, reset
resolution to lower before connecting projector.
● Image data in other than XGA (1024 x 768) is
modified to fit screen size in initial mode.
● Panning function may not operate properly if
computer system prepared on PC ADJUST Menu
is used.
VIDEO INPUT
SELECTING INPUT SOURCE
WHEN SELECT INPUT 2 (5 BNC INPUT JACKS )
When connecting to those equipment, select a type of Video
source in SOURCE SELECT Menu.
1
2
3
INPUT MENU
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button to move the red frame pointer to
INPUT Menu icon.
Press POINT DOWN button to move the red arrow pointer to
Input 2 and then press SELECT button. Source Select Menu will
appear.
INPUT Menu icon
Move the pointer (red arrow)
to Input 2 and press SELECT
button.
Input 2
Source Select Menu
Move the pointer to Video
or
Y, Pb/Cb, Pr/Cr and press
Move a pointer to source that you want to select and then press
SELECT button.
Video
When video input signal is connected to VIDEO jack,
select Video.
Y,Pb/Cb,Pr/Cr
When video input signal is connected to Y-Pb/CbPr/Cr jacks, select Y, Pb/Cb, Pr/Cr.
WHEN SELECT INPUT 3 (AV TERMINALS )
When connecting to those equipment, select a type of Video
source in SOURCE SELECT (VIDEO) Menu.
1
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button to move the red frame pointer to
INPUT Menu icon.
2
Press POINT DOWN button to move the red arrow pointer to
Input 3 and then press SELECT button. Source Select Menu will
appear.
3
Move a pointer to source that you want to select and then press
SELECT button.
Video
INPUT Menu icon
Move the pointer (red arrow)
to Input 3 and press SELECT
button.
Input 3
Source Select Menu (VIDEO)
Move the pointer to source
and press SELECT button.
When video input signal is connected to VIDEO jack,
select Video.
Y,Pb/Cb,Pr/Cr
S-Video
INPUT MENU
When video input signal is connected to Y-Pb/CbPr/Cr jacks, select Y, Pb/Cb, Pr/Cr.
When video input signal is connected to S-VIDEO jack,
select S-Video.
31
VIDEO INPUT
SELECTING VIDEO SYSTEM
1
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT buttons to move the red frame pointer to
AV SYSTEM Menu icon.
2
Press POINT DOWN button to move the red arrow pointer to
system that you want to select and then press SELECT button.
VIDEO JACK OR S-VIDEO JACK
Auto
Projector automatically detects incoming Video system, and adjusts
itself to optimize its performance.
When Video System is PAL-M or PAL-N, select system manually first.
PAL / SECAM / NTSC / NTSC4.43 / PAL-M / PAL-N
If projector cannot reproduce proper video image, it is necessary to
select a specific broadcast signal format among PAL, SECAM, NTSC,
NTSC 4.43, PAL-M, and PAL-N.
AV SYSTEM MENU (VIDEO OR S-VIDEO)
AV SYSTEM Menu icon
This box indicates system
being selected.
Move pointer to system
and press SELECT
button.
Y, Pb/Cb, Pr/Cr JACKS
Auto
Projector automatically detects incoming Video signal, and adjusts
itself to optimize its performance.
When Video System is 1035i or 1080i, select system manually first.
COMPONENT VIDEO SIGNAL FORMAT
If projector cannot reproduce proper video image, it is necessary to
select a specific component video signal format among 480i, 575i,
480p, 575p, 720p, 1035i and 1080i.
32
AV SYSTEM MENU (COMPONENT VIDEO)
AV SYSTEM Menu icon
This box indicates system
being selected.
Move pointer to system
and press SELECT
button.
VIDEO INPUT
PICTURE IMAGE ADJUSTMENTS
IMAGE LEVEL SELECT (DIRECT)
Select image level among Standard, Cinema, Image 1, Image 2,
Image 3 and Image 4 by pressing IMAGE button on Top Control or on
Remote Control Unit.
Select Image 1-4 by pressing IMAGE 1-4 buttons on Remote Control
Unit.
IMAGE button
Standard
Cinema
Standard
Normal picture level preset on this projector.
Image 1
Image 2
Cinema
Picture level adjusted for picture with fine tone.
Image 3
IMAGE 1~4
User preset picture adjustment in IMAGE ADJUST Menu (P34-36).
Image 4
IMAGE LEVEL SELECT (MENU)
1
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button to move the red frame pointer to
IMAGE SELECT Menu icon.
2
Press POINT DOWN button to move the red frame pointer to
level that you want to set and then press SELECT button.
IMAGE SELECT MENU
IMAGE SELECT
Menu icon
Standard
Normal picture level preset on this projector.
Cinema
Move red frame pointer to level
and press SELECT button.
Picture level adjusted for picture with fine tone.
IMAGE 1~4
Level being selected.
User preset picture adjustment in IMAGE ADJUST Menu (P34-36).
33
VIDEO INPUT
IMAGE LEVEL ADJUSTMENT
1
Press MENU button and ON-SCREEN MENU will appear.
Press POINT LEFT/RIGHT button(s) to move the red frame
pointer to IMAGE ADJUST Menu icon.
2
Press POINT DOWN button to move the red frame pointer to
item that you want to adjust and then press SELECT button.
Level of each item is displayed. Adjust each level by pressing
POINT LEFT/RIGHT button(s).
IMAGE ADJUST MENU
Move the red frame pointer
to item to be selected and
then press SELECT button.
IMAGE ADJUST
Menu icon
Contrast
Press POINT LEFT button to decrease contrast, and POINT RIGHT
button to increase contrast. (From 0 to 63.)
Brightness
Press POINT LEFT button to adjust image darker, and POINT
RIGHT button to adjust brighter. (From 0 to 63.)
Color
Press POINT LEFT button to lighten color, and POINT RIGHT button
to deeper color. (From 0 to 63.)
32
Tint
32
Press POINT LEFT button or POINT RIGHT button to obtain proper
color. (From 0 to 63.)
32
Press POINT LEFT/RIGHT buttons
to adjust value.
32
Color Management
The Color management function can be used to adjust the level,
phase and gamma of the selected display colors on the screen, and
to replace these colors with other colors if required.
The projector lets you replace up to eight colors for each image.
There are four preset images for VIDEO mode and four preset
images for PC, giving a total of eight images.
Press the POINT DOWN button to move the red frame pointer to
"COLOR MANAGEMENT", and then press the SELECT button.
The COLOR MANAGEMENT menu will appear and pointer
mode will be enabled. The image that was being projected when
the button was pressed will be paused, and the COLOR MANAGEMENT POINTER will appear.
L1
Press SELECT button at this icon
to display other items.
POINTER MODE
1
2
Use the POINT buttons to move the pointer to a section of the
paused image that contains the color that you would like to
adjust, and then press the SELECT button. The mode will
change to COLOR SELECTION mode, and the color in the center of the pointer will be selected and adjustment will be possible.
3
Use the POINT buttons to adjust the level and phase of the
color, and then press the SELECT button to confirm the setting.
Next, use the POINT buttons to adjust the gamma correction for
the color, and then press the SELECT button to accept the setting. When the SELECT button is pressed, the mode will change
to LIST mode.
To move the red frame pointer to "MENU", and then press the
SELECT button. The message "OK"? is displayed. Move the
pointer to [Yes] and then press SELECT button. The COLOR
MANAGEMENT menu will be exited and the display will return
to the IMAGE ADJUST menu. (At this time, the image will stop
being paused and normal projection will resume.) After changing the COLOR MANAGEMENT settings, use the IMAGE
ADJUST menu to store the changed settings.
4
COLOR
MANAGEMENT
POINTER
NOTE;
Press the COLOR M. button on the remote control to display the COLOR MANAGEMENT menu.
If you would like to check or re-adjust a color
management setting that has already been made,
press the COLOR M. button on the remote control
once more to change to LIST mode.
COLOR SELECTION
MODE
Level and phase
adjustment palette.
Gamma
adjustment palette.
COLOR SELECTION MODE
CANCEL
The mode will return to the pointer mode (even if you press the
MENU key on the projector or the remote control). (You will need to
reselect and re-adjust the color in this case.)
34
LIST
CANCEL
QUIT
VIDEO INPUT
QUIT
The COLOR MANAGEMENT menu will be exited and the display will
return to the normal projection screen, but any settings that have
been changed will not be stored. To store the changed settings, be
sure to select "LIST" using the POINT buttons and change to the
next mode (LIST mode).
LIST MODE
COLOR PALETTE
DEL
LIST MODE
The check mark will be cleared and the effect of the setting adjustment for that line on the projected images will be momentarily canceled.
COLOR PALETTE
The mode will return to COLOR SELECTION mode so that you can
re-adjust the setting for the color in that line. This option is not available if the check mark has been cleared by the operation immediately above.)
DEL
The setting adjustment for the color in that line will be canceled.
ALL DEL
The setting adjustment for the colors in all lines will be canceled.
ALL DEL
Press either POINT LEFT button or POINT RIGHT button to Auto
picture control position that you want to select . (Off, L1 or L2)
Off ······· Auto picture control OFF position.
L1 ········ Auto picture control LEVEL 1 position.
L2 ········ Auto picture control LEVEL 2 position.
Color temp.
Press either POINT LEFT button or POINT RIGHT button to Color
temp. level that you want to select. (XLow, Low, Mid or High)
COLOR M.
If you press the COLOR M. button on the remote
control, the COLOR MANAGEMENT menu will be
exited and the display will return to the normal
projection screen, but any settings that have been
changed will not be stored. To store the changed
settings, be sure to select "MENU" using the
POINT buttons and store the settings.
COLOR M.
The mode will return to POINTER mode.
Auto picture control
MENU
NOTE;
Press SELECT button at this icon
to display previous items.
Mid
32
32
32
Press POINT LEFT/RIGHT buttons
to adjust value.
15
8
On
On
White balance (Red)
Press POINT LEFT button to lighten red tone and POINT RIGHT
button to deeper tone. (From 0 to 63.)
Press SELECT button at this icon to
store value.
White balance (Green)
Press POINT LEFT button to lighten green tone and POINT RIGHT
button to deeper tone. (From 0 to 63.)
White balance (Blue)
Press POINT LEFT button to lighten blue tone and POINT RIGHT
button to deeper tone. (From 0 to 63.)
Sharpness
Press POINT LEFT button to soften image, and POINT RIGHT
button to sharpen image. (From 0 to 15.)
Gamma
Press either POINT LEFT button or POINT RIGHT button to obtain
better balance of contrast. (From 0 to 15.)
Progressive scan
Press POINT LEFT/RIGHT button(s) to change
progressive scan mode. Dialog box display is
changed to “Off” and progressive scan mode to off.
Press POINT LEFT/RIGHT button(s) again,
progressive scan mode to on.
NOTE :
Tint cannot be adjusted when video system is PAL,
SECAM, PAL-M or PAL-N.
Progressive cannot be operated when “480p”,
“575p” or “720p” is selected on AV SYSTEM MENU
(P32).
Noise reduction
Press POINT LEFT/RIGHT button(s) to change noise reduction
mode. Dialog box display is changed to “On” to reduce noise (rough
parts) of image. Press POINT LEFT/RIGHT button(s) again, to
change noise reduction mode to off.
35
VIDEO INPUT
Store
To store adjustment data, move the red frame pointer to Store icon
and press SELECT button. Image Level Menu will appear. Move
the red frame pointer to Image Level 1 to 4 and then press SELECT
button.
Other icons operates as follows.
Mid
32
Image Level Menu
Move the red frame pointer to
image icon to be set and then
press SELECT button.
32
32
Reset
15
Reset all adjustment to previous figure.
8
On
Quit
On
Closes IMAGE MENU.
Store icon
PICTURE SCREEN ADJUSTMENT
PICTURE SCREEN SELECT (DIRECT)
SCREEN button
Select picture screen among Full, Zoom, Normal and Wide zoom by
pressing SCREEN button on Remote Control Unit.
Full
Zoom
Normal
Wide zoom
PICTURE SCREEN SELECT (MENU)
This projector has a picture screen resize function, which enables you to display desirable image size.
1
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button(s) to move the red frame pointer to
SCREEN Menu icon.
2
Press POINT DOWN button and move the red frame pointer to
function that you want to select and then press SELECT button.
Full
Provides image to fit width of screen by expanding image width
uniformly. This function can be used for providing a squeezed video
signal at wide video aspect ratio of 16 : 9.
When your video equipment (such as DVD) has 16 : 9 output mode,
select 16 : 9 and select Full on this SCREEN Menu to provide better
quality.
Zoom
Provides image to fit screen size (16 : 9 aspect ratio) by expanding
image width and height uniformly. This function can be used for
providing a letter box mode picture (4 : 3 aspect picture with black
bar on top and bottom edges) at wide video aspect of 16 : 9.
Normal
Provides image at the normal video aspect ratio of 4 : 3.
Wide zoom
Provides image to fit width of screen by expanding both sides of
image. This function is suitable to provide a normal video signal (4 :
3 aspect ratio) at wide video aspect ratio of 16 : 9.
36
SCREEN MENU
SCREEN Menu icon
Move the red frame to the function and
press SELECT button.
NOTE : SCREEN Menu cannot be operated when
“720p,” “1035i,” or “1080i” is selected on AV
SYSTEM Menu (P32).
SETTING
SETTING MENU
1
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button(s) to move the red-frame pointer to
SETTING icon.
2
Press POINT DOWN button to move the red-frame pointer to
item that you want to set and then press SELECT button.
Setting dialog box appears.
Language
SETTING MENU
Set the red frame
pointer to item and
press SELECT
button.
SETTING Menu icon
Language used in ON-SCREEN MENU is selectable from among
English, German, French, Italian, Spanish, Portuguese, Dutch,
Swedish, Chinese, Korean and Japanese.
Keystone
When image is distorted, select Keystone. ON-SCREEN MENU
disappears and Keystone dialog box is displayed. Correct keystone
distortion by pressing POINT UP/DOWN/LEFT/RIGHT button(s).
Refer to KEYSTONE ADJUSTMENT on page 20.
When pressing SELECT
button at Language,
Language Menu appears.
Blue back
When this function is “On,” this projector will produce a blue image
instead of video noise on screen when any input source is unplugged
or turned off.
Display
This function decides whether to display On-Screen Displays.
On ··· shows all On-Screen Displays.
Off ···· sets On-Screen Displays disappeared except;
● ON-SCREEN MENU
● “Power off?” message
Logo
When this function is “On,” projector displays our logo when starting up.
Ceiling
When this function is “On,” picture is top / bottom and left / right
reversed. This function is used to project image from a ceiling mounted
projector.
Move the pointer to item
and then press POINT
LEFT/RIGHT button(s).
Ceiling function
Rear
When this function is “On,” picture is left / right reversed. This function is
used to project image to a rear projection screen.
Power management
This function turns Projection Lamp off when this projector detects
signal interruption and is not used for a certain period in order to
reduce power consumption and maintain Lamp-life. (This projector is
shipped with this function ON.)
Power Management function operates to turn Projection Lamp off
when input signal is interrupted and any button is not pressed over 5
minutes. This function operates as follows;
1. When any input signal is interrupted, “No signal” and counting
down display appears (for 5 minutes).
2. After counting down for 5 minutes, projector lamp and READY
indicator are turned off.
3. When READY indicator flashing, Projection Lamp can be turned
on again (Power Management mode).
In this Power Management mode, Projection Lamp is
automatically turned on when input signal connected or projector
is operated with any button on Top Control or on Remote Control
Unit again.
Rear function
Time left until Lamp off.
37
SETTING
On start
When this function is “On,” projector is automatically turned on just
by connecting AC Power cord to a wall outlet.
Note ; Be sure to turn projector off properly (refer to section
“TURNING OFF PROJECTOR” on P19). If projector is turned
off in wrong steps, On Start function does not operate
properly.
Remote control
This projector has two different remote control codes; factory-set
normal code (Code 1) and secondary code (Code 2). This switching
function prevents remote control operation mixture (jam) when
operating several projectors or video equipment together.
When operating projector in “Code 2,” both projector and Remote
Control Unit must be switched to “Code 2.”
Press SELECT button at this icon to
display other items.
To change code of Projector;
Set Remote control in SETTING MENU to “Code 2.”
To change code of Remote Control Unit;
Press both MENU and IMAGE buttons on Remote Control Unit
together for over 10 seconds.
After changing code, make sure Remote Control operates properly.
To return to normal code (Code 1), operate both projector and
Remote Control in ways above again.
Network icon
On start
On
Code 1
Press SELECT button at this icon to
display previous items.
Move pointer to item and then press
POINT LEFT/RIGHT button(s).
This function cannot be adjusted when not attach the Network
connection (optional part) to the projector.
Lamp counter reset
This function is used to reset Lamp Replace Counter. When
replacing Projection Lamp, reset Lamp Replace Counter by using
this function. Refer to page 40 for operation.
Lamp
counter reset
Quit
Closes SETTING MENU.
On
Code 1
Move pointer to Lamp counter reset and then press
SELECT button. Message “Lamp replace counter
reset?” is displayed.
38
APPENDIX
MAINTENANCE
WARNING TEMP. INDICATOR
WARNING TEMP. Indicator flashes red when an internal temperature of the projector exceeds normal temperature. This
Indicator stops flashing when temperature of the projector returns to normal.
When WARNING TEMP. Indicator continues to flash, check items listed below.
1
2
3
Ventilation Slots of the projector may be blocked. In such an event, reposition the projector so that Ventilation Slots
are not obstructed.
Air Filter may be clogged with dust particles. Clean Air Filter by following section AIR FILTER CARE AND CLEANING
below.
If WARNING TEMP. Indicator remains on after performing above checks, Cooling Fans or Internal Circuits may be
malfunctioning. Contact service personnel from an authorized dealer or a service station.
AIR FILTER CARE AND CLEANING
Air Filter prevents dust from accumulating on surface of Projection Lens and Projection Mirror. Should Air Filter become
clogged with dust particles, it will reduce Cooling Fans’ effectiveness and may result in internal heat build up and adversely
affect life of the projector. Clean Air Filter following steps below:
1
Turn off the projector, and disconnect AC power cord from AC
outlet.
2
Turn the projector upside down and remove Air Filter (2 used) by
pulling latches upward.
3
4
Clean Air Filter with a brush or wash out dust and particles.
Replace Air Filter properly. Make sure that Air Filter is fully
inserted.
CAUTION
Do not operate the projector with Air Filter removed. Dust
may accumulate on LCD Panel and Projection Mirror
degrading picture quality.
Do not put small parts into Air Intake Vents. It may result
in malfunction of the projector.
AIR FILTER
Pull up and remove.
RECOMMENDATION
We recommend avoiding dusty/smoky environments when operating the projector. Usage in these environments
may cause poor image quality.
When using under dusty or smoky conditions, dust may accumulate on a lens, liquid crystal panels, or optical elements
inside the projector. This condition may degrade quality of the projected image.
When above symptoms are noticed, contact a Boxlight Corporation at 1-800-762-5757 or 360-779-7901 for cleaning.
CLEANING PROJECTION LENS
Follow these steps to clean Projection Lens:
1
Apply a non-abrasive camera lens cleaner to a soft, dry cleaning cloth. Avoid using an excessive amount of cleaner.
Abrasive cleaners, solvents or other harsh chemicals might scratch the surface.
2
3
Lightly wipe a cleaning cloth over Projection Lens.
When the projector is not in use, replace Lens Cover.
39
APPENDIX
LAMP REPLACE
When the life of the Projection Lamp of this projector draws to an end,
the LAMP REPLACE indicator lights yellow. If this indicator lights
yellow, replace the projection lamp with a new one promptly.
TOP CONTROL
This indicator lights yellow
when the life of the projection
lamp draws to an end.
Replace the Projection Lamp
with a new one promptly.
CAUTION
Allow the projector to cool, for at least 45 minutes before
you open Lamp Cover. The inside of the projector can
become very hot.
For continued safety, replace with a lamp assembly of
the same type.
Do not drop the lamp assembly or touch the glass bulb!
The glass can shatter and may cause injury.
Follow these steps to replace lamp assembly.
1
Turn off the projector and disconnect AC plug. Allow the
projector to cool for at least 45 minutes.
2
3
Loosen 2 screws with a screwdriver and open Lamp Cover.
4
Replace Lamp Assembly with a new one and tighten 2 screws
back. Make sure that Lamp Assembly is set properly. Replace
Lamp Cover and tighten 2 screws.
5
6
Connect AC Power Cord to the projector and turn it on.
Loosen 2 screws with a screwdriver and pull out Lamp Assembly
by grasping Handle.
LAMP COVER
LAMP
ASSEMBLY
HANDLE
Reset Lamp Replace Counter (refer to section “Lamp Replace
Counter” below).
NOTE : Do not reset Lamp Replace Counter when Projection
Lamp is not replaced.
ORDER REPLACEMENT LAMP
Replacement Lamp can be ordered through Boxlight Corporation at 1-800-762-5757 or 360-779-7901. When
ordering Projection Lamp, give following information to dealer.
Model No. of your projector
● Replacement Lamp Type No.
●
:
:
STUDIO EXPERIENCE CINEMA 20HD
POA-LMP38
(Service Parts No. 610 293 5868)
40
APPENDIX
LAMP REPLACE COUNTER
Be sure to reset Lamp Replace Counter after the Lamp Assembly is replaced. When Lamp Replace Counter is reset, LAMP
REPLACE Indicator stops lighting.
1
Turn projector on, press MENU button and ON-SCREEN
MENU will appear. Press POINT LEFT/RIGHT button(s) to
move the red frame pointer to SETTING Menu icon (refer to
page 38).
2
Press POINT DOWN button to move the red frame pointer to
“Lamp counter reset” and then press SELECT button.
Message "Lamp replace counter reset?" is displayed. Move
pointer to [Yes] and then press SELECT button.
3
Another confirmation dialog box appears and select [Yes] to
reset Lamp Replace Counter.
Lamp
counter reset
On
Code 1
Move pointer to Lamp counter reset and then press
SELECT button. Message “Lamp replace counter
reset?” is displayed.
NOTE : Do not reset the Lamp Replace Counter until after the Projection Lamp is replaced.
LAMP HANDLING PRECAUTIONS
This projector uses a high-pressure lamp which must be handled carefully and properly. Improper
handling may result in accidents, injury, or create a fire hazard.
● Lamp lifetime may differ from lamp to lamp and according to the environment of use. There is no
guarantee of the same lifetime for each lamp. Some lamps may fail or terminate their lifetime in a
shorter period of time than other similar lamps.
● If the projector indicates that the lamp should be replaced, i.e., if the LAMP REPLACE INDICATOR
lights up, replace the lamp with a new one IMMEDIATELY after the projector has cooled down.
( Follow carefully the instructions in the LAMP REPLACEMENT section of this manual. ) Continuous
use of the lamp with the LAMP REPLACE INDICATOR lighted may increase the risk of lamp explosion.
● A Lamp may explode as a result of vibration, shock or degradation as a result of hours of use as its
lifetime draws to an end. Risk of explosion may differ according to the environment or conditions in
which the projector and lamp are being used.
IF A LAMP EXPLODES, THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE TAKEN.
If a lamp explodes, disconnect the projector’s AC plug from the AC outlet immediately. Contact an
authorized service station for a checkup of the unit and replacement of the lamp. Additionally, check
carefully to ensure that there are no broken shards or pieces of glass around the projector or coming out
from the cooling air circulation holes. Any broken shards found should be cleaned up carefully. No one
should check the inside of the projector except those who are authorized trained technicians and who are
familiar with projector service. Inappropriate attempts to service the unit by anyone, especially those who
are not appropriately trained to do so, may result in an accident or injury caused by pieces of broken
glass.
41
APPENDIX
TROUBLESHOOTING
Before calling your dealer or service center for assistance, check matters below once again.
1. Make sure you have connected the projector to your computer or video equipment as described in section "CONNECTING
PROJECTOR" on pages 11 ~ 13.
2. Check cable connection. Verify that all computer, video and power cord are properly connected.
3. Verify that all power is switched on.
4. If the projector still does not produce an image, re-start your computer.
5. If the image still does not appear, unplug the projector from your computer and check your computer monitor's display.
Problem may be with your graphics controller rather than with the projector. (When you reconnect the projector, be sure
to turn computer and monitor off before you power up the projector. Power equipment back on in order of : Projector and
computer.)
6. If problem still exists, check following chart.
Problem:
No power.
Try these Solutions
● Plug the projector into your AC outlet.
● Make sure READY Indicator lights.
● Wait 90 seconds after the projector is turned OFF when turning the projector back on.
NOTE : After pressing Power ON-OFF button to OFF, make sure the projector works as
follows:
1. LAMP indicator lights bright and READY indicator turns off.
2. After 90 seconds, READY indicator lights green again and the projector may be
turned on by pressing Power ON-OFF button.
● Check WARNING TEMP. indicator. If indicator flashes red, the projector cannot be turned
on.
(See "TURNING ON/OFF PROJECTOR" section on page 19.)
● Check Projection Lamp. (Refer to page 40.)
Image is out of
focus.
● Adjust focus of the projector.
● Make sure the projection screen is at least 5.0’ (1.5m) from the projector.
● Check Projection Lens to see if it needs cleaning.
NOTE : Moving the projector from a cool temperature location to a warm temperature
location may result in moisture condensation on Projection Lens. In such an event,
leave the projector OFF and wait until condensation disappears.
Picture is Left/Right
reversed.
● Check Ceiling / Rear feature. (See “SETTING” section on page 37.)
Picture is
Top/Bottom
reversed.
● Check Ceiling feature. (See “SETTING” section on page 37.)
Some displays are
not seen during
Operation.
● Check Display feature.(See “SETTING” section on page 37.)
No image.
● Check connection between your computer or video equipment and the projector.
● When turning the projector on, it takes about 30 seconds to display an image.
● Check system that you select is corresponding with your computer or video equipment.
● Make sure temperature is not out of Operating Temperature (5°C ~ 35°C).
No sound.
42
● Check audio cable connection from audio input source.
● Adjust audio source.
● Press VOLUME (+) button.
● Press MUTE button.
APPENDIX
Problem:
Remote Control Unit
does not work.
Try these Solutions
● Check batteries.
● Make sure nothing is between Infrared Remote Receiver and Remote Control Unit.
● Make sure you are not too far from the projector when using Remote Control Unit.
Maximum operating range is 16.4’ (5m).
● Check transmitted signal mode from Remote Control Unit.
(See“SETTING” section on page 38.)
SERVICE
WARNING: High voltages are used to operate this projector. Do not attempt to open the cabinet.
Boxlight Service is easily obtained. If after following instructions above, you find that service is necessary, contact Boxlight for assistance at 1-800-762-5757 or 360-779-7901.
Give the model number and explain the difficulty. We will advise you how to obtain service.
Please have the following information available:
● Serial Number of Projector.
● Resolution of Computer.
● Refresh rate of Computer.
This symbol on the nameplate means the product is Listed by Underwriters
Laboratories Inc. It is designed and manufactured to meet rigid U.L. safety
standards against risk of fire, casualty and electrical hazards.
The CE Mark is a Directive conformity mark of the European Community (EC).
43
APPENDIX
TECHNICAL SPECIFICATIONS
Projector Type
Dimensions (W x H x D)
Net Weight
LCD Panel System
Panel Resolution
Number of Pixels
Color System
High Definition TV Signal
Scanning Frequency
Projection Lens
Throw distance
Motorized Lens Shift
Multi-media Projector
12.6" x 6.6" x 16.8" (319 mm x 168 mm x 429.5 mm)
17.4 lbs (7.9 kg)
1.21" TFT Active Matrix type, 3 panels
1366 x 768 dots
3,147,264 (1366 x 768 x 3 panels)
PAL, SECAM, NTSC, NTSC4.43, PAL-M and PAL-N
480i, 480p, 575i, 575p, 720p, 1035i and 1080i
H-sync. 15 ~ 100 KHz, V-sync. 50 ~ 100 Hz
F1.8 ~ 2.1 lens with f=48.4 mm ~ 62.8 mm Motor zoom and focus
5.0' (1.5 m) ~ 51.3' (15.6 m)
Up and Down
Projection Image Size (Diagonal)
Adjustable from 31" to 400"
Horizontal Resolution
Projection Lamp
Input 1 Jacks
800 TV lines (HDTV)
200 watt type
DVI Terminal (Digital), HDB 15-pin Terminal (Analog)
and Stereo Mini Type Jack (Audio)
Input 2 Jacks
BNC Type x 5 (G or VIDEO/Y, B or Cb/Pb, R or Cr/Pr, H and V), Stereo Mini
Type Jack (Audio)
Input 3 Jacks
RCA Type x 3 (VIDEO/Y, Cb/Pb and Cr/Pr), RCA Type x 2 (Audio R and L)
and DIN 4-pin (S-Video)
Other Jacks
Built-in Speakers
Feet Adjustment
Voltage and
Power Consumption
Operating Temperature
Storage Temperature
Accessories
DIN 8-pin (Control port), Wired Remote Jack and Network Connector
INT. SP. Stereo (R and L), 2 watt RMS (T.H.D. 10%)
0˚ to 10.5˚
AC 100 ~ 120 V (3.6 A Max. Ampere), 50 / 60 Hz (The U.S.A and Canada)
AC 200 ~ 240 V (1.8 A Max. Ampere), 50 / 60 Hz (Continental Europe)
41 ˚F ~ 95 ˚F (5 ˚C ~ 35 ˚C)
14 ˚F ~ 140 ˚F (-10 ˚C ~ 60 ˚C)
User’s Guide
AC Power Cord
Wireless/Wired Remote Control Transmitter and Batteries
Remote Control Cable
Video Cable (RCA x 1)
Audio Cable (RCA x 2)
S-Video Cable
Control (Serial) port Cable
Protective Dust Cover
Lens Cover
● Specifications are subject to change without notice.
● LCD panels are manufactured to the highest possible standards. At least 99.99% of the pixels are effective,
however a tiny fraction of the pixels (0.01% or less) may be ineffective by the characteristics of the LCD
panels.
44
APPENDIX
CONFIGURATIONS OF TERMINALS
COMPUTER INPUT-1 TERMINAL (ANALOG)
Terminal : HDB15-PIN
Connect display output terminal of computer to this terminal with VGA Cable (not supplied). When connecting Macintosh
computer, MAC Adapter (not supplied) is required.
Pin Configuration
4
5
10
15
14
2
3
9
8
13
1
7
12
6
11
1
2
3
4
5
6
7
8
Red Input
Green Input
Blue Input
Sense 2
Ground (Horiz.sync.)
Ground (Red)
Ground (Green)
Ground (Blue)
9
10
11
12
13
14
15
+5V Power
Ground (Vert.sync.)
Sense 0
DDC Data
Horiz. sync.
Vert. sync.
DDC Clock
COMPUTER INPUT-1 TERMINAL (DIGITAL)
Terminal : DVI 24-pin
Connect display output terminal of computer to this terminal with DVI cable (for Single Link T.M.D.S. / not supplied).
Pin Configuration
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
17 18 19 20 21 22 23 24
1
2
3
4
5
6
7
8
T.M.D.S. Data2–
T.M.D.S. Data2+
T.M.D.S. Data2 Shield
No Connect
No Connect
DDC Clock
DDC Data
No Connect
9
10
11
12
13
14
15
16
T.M.D.S. Data1–
T.M.D.S. Data1+
T.M.D.S. Data1 Shield
No Connect
No Connect
+5V Power
Ground (for +5V)
Hot Plug Detect
17
18
19
20
21
22
23
24
T.M.D.S. Data0–
T.M.D.S. Data0+
T.M.D.S. Data0 Shield
No Connect
No Connect
T.M.D.S. Clock Shield
T.M.D.S. Clock+
T.M.D.S. Clock–
CONTROL PORT CONNECTOR
Terminal : Mini DIN 8-PIN
Connect serial port on your computer to this connector with Control Cable (supplied).
Pin Configuration
8
5
7 6
4 3
2 1
1
2
3
4
5
6
7
8
PS/2
----CLK
DATA
GND
--------GND
-----
Serial
RXD
--------GND
RTS / CTS
TXD
GND
GND
ADB
----ADB
----GND
------------GND
45
46
47
LIMITED WARRANTY
BOXLIGHT Corporation (“BOXLIGHT”) warrants that each Cinema 20HD (“the Product”) sold hereunder will conform to and
function in accordance with the written specifications of BOXLIGHT. Said limited warranty shall apply only to the first
person or entity that purchases the Product for personal or business use and not for the purpose of distribution or resale.
Said warranty shall continue for a period of three (3) years from the date of such purchase. The standard limited warranty
excludes the lamps in projectors after 120 days and the accessories after one year. BOXLIGHT does not warrant that the
Product will meet the specific requirements of the first person or entity that purchases the Product for personal or business
use. BOXLIGHT’s liability for the breach of the foregoing limited warranty is limited to the repair or replacement of the
Product or refund of the purchase price of the Product, at BOXLIGHT’s sole option. Replacement Product may be refurbished in “like-new” condition, at BOXLIGHT’s sole discretion. To exercise the Purchaser’s rights under the foregoing
warranty, the Product must be returned at the Purchaser’s sole cost and expense, to BOXLIGHT or to any authorized
BOXLIGHT service center provided, and the Product must be accompanied by a written letter explaining the problem and
which includes (i) proof of date of purchase; (ii) the dealer’s name; and (iii) the model and serial number of the Product.
When sending your unit in for repair, please ship your unit in its original packing material or a BOXLIGHT approved ATA
Shipping Case, or have a professional packaging company pack the unit. Please insure your shipment for its full value.
A return authorization number, issued by the BOXLIGHT customer service department, must also be clearly
displayed on the outside of the shipping carton containing the Product.
WARRANTY LIMITATION AND EXCLUSION
BOXLIGHT shall have no further obligation under the foregoing limited warranty if the Product has been damaged due to
abuse, misuse, neglect, accident, unusual physical or electrical stress (unusual physical and electrical stress includes
unusually long operation, exposure to smoke and other airborne contaminants), unauthorized modifications, tampering,
alterations,
or service other than by BOXLIGHT or its authorized agents, causes other than from ordinary use or failure to properly use
the Product in the application for which said Product is intended.
DISCLAIMER OF UNSTATED WARRANTIES
THE WARRANTY PRINTED ABOVE IS THE ONLY WARRANTY APPLICABLE TO THIS PURCHASE. ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. THERE ARE NO
WARRANTIES THAT EXTEND BEYOND THE FACE HEREOF AND THE FOREGOING WARRANTY SHALL NOT BE
EXTENDED, ALTERED OR VARIED EXCEPT BY WRITTEN INSTRUMENT SIGNED BY BOXLIGHT. SOME STATES DO
NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY MAY LAST, SO SUCH LIMITATIONS MAY NOT
APPLY TO YOU.
LIMITATION OF LIABILITY
IT IS UNDERSTOOD AND AGREED THAT BOXLIGHT’S LIABILITY WHETHER IN CONTRACT, IN TORT, UNDER ANY
WARRANTY, IN NEGLIGENCE OR OTHERWISE SHALL NOT EXCEED THE RETURN OF THE AMOUNT OF THE
PURCHASE PRICE PAID BY PURCHASER AND UNDER NO CIRCUMSTANCES SHALL BOXLIGHT BE LIABLE FOR
SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOST PROFITS, LOST REVENUES OR
LOST SAVINGS. THE PRICE STATED FOR THE PRODUCT IS A CONSIDERATION IN LIMITING BOXLIGHT’S
LIABILITY. NO ACTION, REGARDLESS OF FORM, ARISING OUT OF THE AGREEMENT TO PURCHASE THE
PRODUCT MAY BE BROUGHT BY PURCHASER MORE THAN ONE YEAR AFTER THE CAUSE OF ACTION HAS
ACCRUED. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS
LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS THAT
VARY FROM STATE TO STATE.
Printed in Japan
Part No. 610 303 0365 (1AA6P1P3653-- M4LE)
Boxlight
19332 Powder Hill Place
Poulsbo, WA 98370-7407 USA
www.boxlight.com
U.S. and Canada 800-762-5757
International 1-360-779-7901