BOXLIGHT CP-15t Projector User Manual

USER’S GUIDE
BOXLIGHT CP-15t
BOXLIGHT
®
INFORMATION TO THE USER
NOTE : This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful interference in which case the user will
be required to correct the interference at his own expense.
TO THE OWNER
As the owner of the Boxlight CP-15t, you are probably eager to try out your new projector. Before you do, we
suggest that your spend a little time reading this manual to familiarize yourself with the operating procedures,
so that you will receive maximum satisfaction from the many features included in your new projector.
This owner's manual will acquaint you with your projector's features. Reading it will help us too. Through the
years, we have found that many service requests were not caused by problems with our projectors. They
were caused by problems that could have been prevented, if the owner had followed the instructions in the
manual.
You can often correct operating problems yourself. If your projector fails to work properly, see
"TROUBLESHOOTING" section on pages 44 ~ 45 and try the solution marked for each problem.
SAFETY PRECAUTIONS
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
This Boxlight CP-15t has a grounding-type AC line plug. This is a safety feature to be sure that the plug
will fit into the power outlet. Do not try to defeat this safety feature.
This projector produces intense light from the projection lens. Do not stare directly into the lens as
possible eye damage could result. Be especially careful that children do not stare directly into the beam.
The Remote Control Unit, supplied to this projector, emits the laser beam as the Laser Pointer function
from the Laser Light Window while pressing the LASER button. Do not look into the Laser Light Window
or shine the laser beam on yourself or other people. Eye damage may result.
This projector should be set in the way indicated. If not, It may result in fire hazard.
If the projector will not be used for an extended time, unplug the projector from the power outlet.
READ AND KEEP THIS OWNER'S MANUAL FOR LATER USE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE EXCEPT LAMP REPLACEMENT. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
THIS SYMBOL INDICATES THAT
DANGEROUS VOLTAGE CONSTITUTING
A RISK OF ELECTRIC SHOCK IS
PRESENT WITHIN THIS UNIT.
2
THIS SYMBOL INDICATES THAT THERE
ARE IMPORTANT OPERATING AND
MAINTENANCE INSTRUCTIONS IN THE
OWNER'S MANUAL WITH THIS UNIT.
IMPORTANT SAFETY INSTRUCTIONS
All the safety and operating instructions should be read before
the product is operated.
Read all of the instructions given here and retain them for
later use. Unplug this projector from AC power supply before
cleaning. Do not use liquid or aerosol cleaners. Use a damp
cloth for cleaning.
Do not use attachments not recommended by the
manufacturer as they may cause hazards.
Do not place this projector on an unstable cart, stand, or
table. The projector may fall, causing serious injury to a child
or adult, and serious damage to the projector. Use only with
a cart or stand recommended by the manufacturer, or sold
with the projector. Wall of shelf mounting should follow the
manufacturer's instructions, and should use a mounting kit
approved by the manufacturers.
Do not expose this unit to rain or use near water... for
example, in a wet basement, near a swimming pool, etc...
d. If the projector does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions as improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the projector to normal operation.
e. If the projector has been dropped or the cabinet has been
damaged.
f. When the projector exhibits a distinct change in
performance-this indicates a need for service.
When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer that have the same characteristics as the
original part. Unauthorized substitutions may result in fire,
electric shock, or injury to persons.
Upon completion of any service or repairs to this projector,
ask the service technician to perform routine safety checks to
determine that the projector is in safe operating condition.
Slots and openings in the back and bottom of the cabinet are
provided for ventilation, to insure reliable operation of the
equipment and to protect it from overheating.
The openings should never be covered with cloth of other
materials, and the bottom opening should not be blocked by
placing the projector on a bed, sofa, rug, or other similar
surface. This projector should never be placed near or over a
radiator or heat register.
This projector should not be placed in a built-in installation
such as a book case unless proper ventilation is provided.
GROUND
Follow all warnings and instructions marked on the projectors.
For added protection to the projector during a lightning storm,
or when it is left unattended and unused for long periods of
time, unplug it from the wall outlet. This will prevent damage
due to lightning and power line surges.
This projector should be operated only from the type of power
source indicated on the marking label. If you are not sure of
the type of power supplied, consult your authorized dealer or
local power company.
An appliance and cart combination
should be moved with care. Quick
stops, excessive force, and uneven
surfaces may cause the appliance
and cart combination to overturn.
Do not overload wall outlets and extension cords as this can
result in fire or electric shock. Do not allow anything to rest
on the power cord. Do not locate this projector where the
cord may be damaged by persons walking on it.
Never push objects of any kind into this projector through
cabinet slots as they may touch dangerous voltage points or
short out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the projector.
Do not attempt to service this projector yourself as opening or
removing covers may expose you to dangerous voltage or
other hazards. Refer all servicing to qualified service
personnel.
Unplug this projector from wall outlet and refer servicing to
qualified service personnel under the following conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the projector.
c. If the projector has been exposed to rain or water.
This projector is equipped with a
grounding type AC line plug.
Should you be unable to insert the
plug into the outlet, contact your
electrician. Do not defeat the
safety purpose of this grounding
type plug.
If the projector is to be built into a compartment or similarly
enclosed, the minimum distances must be maintained.
Do not cover the ventilation slot on the projector.
Heat build-up can reduce the service life of your projector,
and can also be dangerous.
20cm
PROJECTOR
(FRONT)
50cm
WALL
PROJECTOR
(SIDE)
50cm
50cm
3
TABLE OF CONTENTS
FEATURES AND DESIGN
PREPARATION
NAME OF EACH PART OF THE PROJECTOR
SETTING UP THE PROJECTOR
CONNECTING THE AC POWER CORD
VENTILATION
MOVING THE PROJECTOR
CONNECTING THE PROJECTOR
TERMINALS OF THE PROJECTOR
CONNECTING TO THE VIDEO EQUIPMENT
CONNECTING TO THE COMPUTER
BEFORE OPERATION
OPERATION OF THE REMOTE CONTROL
TOP CONTROLS AND INDICATORS
OPERATING ON-SCREEN MENU
BASIC OPERATION
TURNING ON / OFF THE PROJECTOR
ADJUSTING THE PICTURE
PICTURE FREEZE / NO SHOW FUNCTION
CURSOR FUNCTION
SOUND ADJUSTMENT
5
6
6
7
8
8
9
10
10
11
12
16
16
18
19
22
22
23
23
23
24
COMPUTER MODE
SELECTING COMPUTER MODE
SELECTING COMPUTER SYSTEM
PC ADJUSTMENT
COMPATIBLE COMPUTER SPECIFICATIONS
PICTURE IMAGE ADJUSTMENT
PICTURE POSITION ADJUSTMENT
PICTURE SCREEN ADJUSTMENT
VIDEO MODE
SELECTING VIDEO MODE
SELECTING COLOR SYSTEM
PICTURE IMAGE ADJUSTMENT
PICTURE SCREEN ADJUSTMENT
MCI MODE
OPERATING THE PC CARD SLOT
SHOW THE DATA IN THE MEMORY CARD
PICTURE IMAGE ADJUSTMENT
PICTURE POSITION ADJUSTMENT
PICTURE SCREEN ADJUSTMENT
WRITE DATA INTO THE MEMORY CARD
SMART MEDIA AND PC CARD ADAPTER
SETTING
SETTING MENU
SETTING LANGUAGE
APPENDIX
OPERATING WIRELESS MOUSE
MAINTENANCE
TROUBLESHOOTING
TECHNICAL SPECIFICATIONS
25
25
25
26
27
28
30
30
31
31
31
32
32
33
33
34
35
36
36
37
38
40
40
40
41
41
42
44
46
TRADEMARKS
● Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer,Inc.
● IBM and PS/2 are trademarks or registered trademarks of International Business Machines, Inc.
● Windows and PowerPoint are registered trademarks of Microsoft Corporation.
● Each name of corporations or products in the owner's manual is a trademark or a registered trademark of its
respective corporation.
4
FEATURES AND DESIGN
This Multimedia Projector is designed with the most
advanced technology for portability, durability, and
ease of use. The projector utilizes built-in multimedia
features, a palette of 16.77 million colors, and matrix
liquid crystal display (LCD) technology.
◆
Compatibility
This projector is compatible with many different
types of personal computers and video devices,
including;
● IBM-compatible computers, including laptops,
up to 1280 x 1024 resolution.
● Apple Macintosh and PowerBook computers
up to 1280 x 1024 resolution.
● Various video equipment using any of the
world wide video standards, including NTSC,
NTSC4.43, SECAM, PAL, and PAL-M.
◆
Portability
This projector is
weight. Having
attaché case with
projector will help
wherever you go.
◆
extremely compact in size and
a sophisticated shape like an
a retractable carrying handle, the
you make powerful presentations
Automatic Multiscanning System
This projector can detect output signals from most
personal computers currently distributed. It is free
from complicated adjustments to project picture
images from PC.
◆
PC CARD SLOT
This projector has a PC CARD SLOT for easier
presentation. Pictures can be projected just by
inserting a memory card including image data. The
presentation data can be edited by the software
"Media Card Imager" (supplied). Refer to pages 33
~ 39 and the Owner's Manual for Media Card
Imager for instructions.
◆
Laser Pointer and Cursor Function
The Laser Pointer and Cursor functions are
provided with the Remote Control Unit. Refer to the
pages 16 and 23 for operations.
◆
Other Features
This projector has Picture Freeze, Mute functions,
and Digital Zoom.
Image Resolution
Picture Image is projected in the resolution of 1024
x 768. The projector provides computer images just
as they appear on your computer's monitor. Screen
resolutions between 1024 x 768 and 1280 x 1024
are compressed to 1024 x 768. The projector
cannot display screen resolutions above 1280 x
1024. If your computer's screen resolution is higher
than 1280 x 1024, reset it to a lower resolution
before you connect the projector.
◆
◆
◆
Accessories
This projector comes with the parts listed below.
Check to make sure all are included. If any parts
are missing, contact to Boxlight.
● Owner's Manual.
● AC Power Cord.
● Wireless Remote Control Unit.
● Batteries for Remote Control Unit.
● VGA Cable.
● VGA/MAC Adapter.
● Mouse Cable for PS/2 port.
● Mouse Cable for serial port.
● Mouse Cable for ADB port.
● MCI Cable (RS-232C Cable).
● Media Card Imager for Windows 95 (CD-ROM)
and Owner's Manual for this software.
● SmartMedia (Memory Card).
● PC Card Adapter for SmartMedia.
● Lens Cover.
● Carrying Bag.
Multilanguage
MENU DISPLAY is displayed in; English, Deutsch,
Français, Italiano, Español, or Japanese
5
PREPARATION
NAME OF EACH PART OF THE PROJECTOR
FRONT OF THE CABINET
PROJECTION LENS
INFRARED REMOTE RECEIVER
SPEAKER (Monaural)
LENS COVER
BACK OF THE CABINET
EXHAUST VENT
HOT AIR EXHAUSTED !
Air blown from the exhaust vent is
hot. When using or installing the
projector, following attention should
be taken.
● Do not put a flammable object near
this part.
Keep heat-sensitive objects away
from the exhaust vent.
● Do not touch this part especially the
screws and metallic parts. This part
will become hot while the projector is
used.
PC CARD SLOT
CARRY HANDLE
POWER CORD CONNECTOR
INFRARED REMOTE RECEIVER
BOTTOM OF THE CABINET
AIR INTAKE VENT
This Air Intake Vent
should not be blocked.
LAMP COVER
6
ADJUSTABLE FEET
PREPARATION
SETTING-UP THE PROJECTOR
Positioning the Projector
● This projector is basically designed to project on a flat projection surface.
● The projector can be focused from 4.6'(1.4m) ~ 35.4'(10.8m).
● Refer to the figure below to adjust the screen size.
35.4' (10.8m)
24.0' (7.3m)
300"
(762cm)
18.0' (5.5m)
200"
(508cm)
H1
11.8' (3.6m)
150"
(381cm)
230"
(584.2cm)
154"
(391.2cm)
4.6' (1.4m)
100"
(254cm)
115"
(292.1cm)
40"
(101.6cm)
77"
(195.6cm)
H2
30"
(76.2cm)
Screen Size
(W x H) mm
30”
60”
100”
150”
200”
300”
609 x 457
1219 x 914
2032 x 1524
3048 x 2286
4064 x 3048
6096 x 4572
Height (H1)
17.1”(435mm)
34.3”(870mm)
57.1”(1451mm)
85.7”(2177mm)
Height (H2)
0.9”(22mm)
1.7”(44mm)
2.9”(73mm)
4.3”(109mm)
114.3”(2903mm) 171.4”(4354mm)
5.7”(145mm)
8.6”(218mm)
ROOM LIGHT
The brightness in the room greatly influences the quality of the image. Darkening the lights in a room will
enhance the projected image.
Adjustable Feet
Picture tilt and projection angle can be adjusted by
twisting ADJUSTABLE FEET. Projection angle can be
adjusted 0 to 2 degrees by rotating Adjustable Feet.
UP
DOWN
UP
DOWN
ADJUSTABLE FEET
7
PREPARATION
CONNECTING THE AC POWER CORD
This projector uses nominal input voltages of 100-120 V
AC 200-240 V AC. The projector automatically selects
the correct input voltage. It is designed to work with
single-phase power systems having a grounded neutral
conductor. To reduce the risk of electrical shock, do not
plug into any other type of power system.
Consult your authorized dealer or service station if your
are not sure of the type of power supply being in use.
Connect the projector with the peripheral equipment
before turning the projector on. (Refer to pages 10 ~15
for connection.)
Connect the AC power supply cord (provided) to the
projector.
The socket-outlet must be near this equipment and
must be easily accessible.
CAUTION
For the safety, unplug the AC Power Cord when the
appliance is not in use.
When this projector is connected to the outlet with
the AC Power Cord, the appliance is in Stand-by
Mode and consumes a little electric power.
Projector side (Female)
AC outlet side (Male)
Ventilation
This projector is equipped with cooling fans for protection from overheating. Pay attention to the following to
ensure proper ventilation and avoid a possible risk of fire and malfunction.
● Do not cover the vent slot.
● Keep the rear grill at least one meter away from any object.
● Make sure that there is no object under the projector. An
object under the projector may prevent the projector from
taking the cooling air through the bottom vent slot.
EXHAUST VENT
(REAR SIDE)
AIR INTAKE VENT
(BOTTOM SIDE)
8
PREPARATION
Moving the Projector
Use the Carry Handle when moving the Projector.
● Replace the lens cover and rotate the feet fully
clockwise (to shorten the feet) when moving the
projector to prevent damage to the cabinet.
NOTE
The carrying bag (supplied) is intended for protection
from dust and scratches on the surface of the cabinet,
and it is not designed to protect the LCD projector from
external shock.
Do not drop the projector, subject it to strong forces, or
put other things on the cabinet when carrying the projector with this bag. Do not transport the projector
through a courier or transport services with this bag.
The projector can be damaged.
CAUTION IN CARRYING OR TRANSPORTING THE PROJECTOR
● Do not drop or give a shock to the projector, otherwise damages or malfunctions may result.
● When carrying the projector, use a carrying case recommended by Boxlight.
● Do not transport the projector by using a courier or transport service in an unsuitable transport case. This
may cause damage to the projector. To transport the projector through a courier or transport service, use
a case recommended by Boxlight.
● For carrying or transportation cases, contact a Boxlight authorized dealer.
9
CONNECTING THE PROJECTOR
TERMINALS OF THE PROJECTOR
COMPUTER INPUT TERMINAL
MONITOR OUTPUT TERMINAL
Connect the computer output
to this terminal.
(Refer to P12 ~15.)
Connect the monitor to this
terminal to view the image on
the monitor.
(Refer to P12 ~15.)
CONTROL PORT CONNECTOR
MCI SERIAL TERMINAL
When controlling the computer
with the Remote Control of this
projector, connect the mouse
port to this terminal.
(Refer to P12 ~15.)
CONTROL PORT
MCI SERIAL
AUDIO IN
COMPUTER AUDIO INPUT JACK
R-AUDIO-L
Connect the audio output from
the computer to this terminal.
(Refer to P12 ~15.)
This terminal is used to
connect a computer to edit
(write and read) the data of PC
card with "Media Card Imager."
(Refer to P12 ~15, 37.)
MONITOR OUT
COMPUTER IN
AUDIO OUT
AUDIO OUTPUT JACK
▼ S-VIDEO
VIDEO
Connect the audio amplifier to
this terminal.
(Refer to P12 ~15.)
(MONO)
RESET BUTTON
AUDIO INPUT JACKS
Connect the audio outputs
from the video equipment
to these terminals.
(Refer to P11.)
● When the audio output is
monaural, connect it to
the Left Audio jack.
VIDEO INPUT JACK
S-VIDEO INPUT JACK
Connect the composite
(RCA) video output from
the video equipment to
this terminal.
(Refer to P11.)
Connect the S-VIDEO
output from the video
equipment to this terminal.
(Refer to P11.)
This projector uses a micro
processor to control the unit.
Occationally,
the
micro
processor may malfunction and
need to be reset. This can be
done by pressing the RESET
button with a pen, which will
shut down the unit. Turn the
projector off and restart the unit.
Do not use the RESET function
excessively.
COMPUTER INPUT / MONITOR OUTPUT TERMINAL
Terminal : HDB15-PIN
Connect the display output terminal of the
computer to COMPUTER INPUT with the
VGA Cable (supplied). And connect the
monitor to MONITOR OUTPUT with the
monitor cable (not supplied). When
connecting the Macintosh computer, the
MAC/VGA Adapter is required.
Pin Configuration
4
5
2
3
10
15
9
14
8
13
1
7
12
6
11
1
2
3
4
5
6
7
8
CONTROL PORT CONNECTOR
Terminal : MULTI-POLE 12-PIN
When controlling the computer with the
projector's Wireless Remote Control Unit,
connect control port (PS/2, Serial or ADB
port) on your computer to this terminal.
(Three types of cables are supplied.)
Pin Configuration
2
1
6
5
4
3
10
9
8
7
12 11
10
1
2
3
4
5
6
7
8
9
10
11
12
Red Input
Green Input
Blue Input
Sense 2
Ground (Horiz.sync.)
Ground (Red)
Ground (Green)
Ground (Blue)
9
10
11
12
13
14
15
Non Connect
Ground (Vert.sync.)
Sense 0
Sense 1
Horiz. sync.
Vert. sync.
Reserved
PS/2
Serial
ADB
-----
TXD
-------------
-----
CLK
DATA
---------------------
READY
-----
ADB
-------------------------
GND
-------------
GND
-------------
GND
-------------
RXD
-----
CONNECTING THE PROJECTOR
CONNECTING TO THE VIDEO EQUIPMENT
Satellite
TV Tuner
Video Cassette Recorder
Video Disc Player
Video / Audio Output
S-VIDEO Output
Use Cables and Adapter indicated below.
Use either the VIDEO jack or
S-VIDEO jack. When both
jacks are connected, the SVIDEO jack has priority over
the VIDEO jack.
· VIDEO CABLE (not supplied)
· S-VIDEO CABLE (not supplied)
· AUDIO CABLE (not supplied)
Video Audio Cable
(Not supplied)
S-VIDEO Cable
(Not supplied)
Terminals
of the Projector
MONITOR OUT
COMPUTER IN
CONTROL PORT
AUDIO IN
R-AUDIO-L
VIDEO
MCI SERIAL
AUDIO OUT
▼ S-VIDEO
(MONO)
Audio Cable
(Stereo / Not supplied)
Audio Input
External Audio Equipment
NOTE :
When connecting the cables, the power cords of
both the projector and the external equipment
should be disconnected from the AC outlet. Turn
the projector and peripheral equipment on before
the computer is switched on.
Audio Speaker
(stereo)
Audio Amplifier
11
CONNECTING THE PROJECTOR
CONNECTING TO THE IBM-COMPATIBLE COMPUTER
To connect with the IBM-compatible computer, refer to the figure below.
Use Cables and Adapter indicated below.
· VGA CABLE (supplied)
· MOUSE CABLE FOR PS/2 PORT or SERIAL PORT (supplied)
· MCI SERIAL CABLE (supplied)
· MONITOR CABLE (not supplied)
· AUDIO CABLE (stereo /not supplied)
◆ Be sure to connect the MOUSE CABLE corresponding with the mouse terminal on your computer.
NOTE :
When connecting the cable, the power cords of both the projector and the external equipment should be
disconnected from the AC outlet. Turn the projector and peripheral equipment on before the computer is
switched on.
IBM-COMPATIBLE COMPUTERS (VGA / SVGA / XGA / SXGA)
Desktop type
Laptop type
Monitor
Audio Speaker
(stereo)
Audio Amplifier
To the Monitor
To each terminal of your computer
Monitor Output
Serial port
Serial port
Terminal
PS/2 port Audio Output
Audio Input
Terminal
Audio Cable
(stereo / not supplied)
Mouse Cable for PS/2 Port (supplied)
Mouse Cable for Serial Port (supplied)
MCI Serial Cable (supplied)
VGA Cable (supplied)
Monitor Cable (not supplied)
12
CONNECTING THE PROJECTOR
MONITOR OUT
COMPUTER IN
CONTROL PORT
AUDIO IN
R-AUDIO-L
VIDEO
MCI SERIAL
AUDIO OUT
▼ S-VIDEO
(MONO)
CONTROL PORT
AUDIO IN
AUDIO OUT
MONITOR OUT
A
MCI SERIAL
B
COMPUTER IN
To disconnect MOUSE CABLE,
1. Hold the portion (B) of the
connector with one hand.
2. Pull the portion (A) to the
arrow direction and remove
connector.
Use either of these Mouse Cables corresponding
with your terminal of your computer.
13
CONNECTING THE PROJECTOR
CONNECTION TO THE MACINTOSH COMPUTER
To connect with the Macintosh computer, refer to the figure below.
Use Cables and Adapter indicated below.
· VGA CABLE (supplied)
· VGA/MAC ADAPTER (supplied)
· MOUSE CABLE FOR ADB PORT (supplied)
· MONITOR CABLE (not supplied)
· PC AUDIO CABLE (stereo / not supplied)
NOTE :
When connecting the cable, the power cords of both the projector and the external equipment should be
disconnected from the AC outlet. Turn the projector and peripheral equipment on before the computer is
switched on.
MACINTOSH COMPUTERS (VGA / SVGA / XGA / SXGA)
Desktop type
Laptop type
Monitor
Audio Speaker
(stereo)
Audio Amplifier
To the Monitor
To each terminal of your computer
Monitor Output
ADB port Audio Output
Audio Input
MAC Adapter (supplied)
ON
DIP
1 2 34 5 6
Set the switches to correspond
with the RESOLUTION MODE
that you want to use before
your turn on the projector and
computer
Terminal
Audio Cable
(stereo / not supplied)
Mouse Cable for ADB Port (supplied)
VGA Cable (supplied)
Monitor Cable (not supplied)
14
CONNECTING THE PROJECTOR
◆ MAC/VGA ADAPTER
Set the switches as shown in the table below depending on the RESOLUTION MODE that
you want to use before your turn on the projector and computer.
1
2
3
4
5
6
13" MODE (640 x 480)
ON
ON
OFF
OFF
OFF
OFF
16" MODE (832 x 624)
OFF
ON
OFF
ON
OFF
OFF
19" MODE (1024 x 768)
OFF
ON
ON
OFF
OFF
OFF
21" MODE (1152 x 870)
ON
ON
ON
ON
OFF
OFF
ON
DIP
1 2 3 4 5 6
OFF
MONITOR OUT
COMPUTER IN
CONTROL PORT
AUDIO IN
R-AUDIO-L
ON
VIDEO
MCI SERIAL
AUDIO OUT
▼ S-VIDEO
(MONO)
CONTROL PORT
AUDIO IN
AUDIO OUT
MONITOR OUT
A
B
To disconnect MOUSE CABLE,
1. Hold the portion (B) of the
connector with one hand.
2. Pull the portion (A) to the
arrow direction and remove
connector.
COMPUTER IN
15
BEFORE OPERATION
OPERATION OF THE REMOTE CONTROL
This remote control unit is not only able to operate the projector but also usable as a wireless mouse for a PC.
The POINT button and two CLICK buttons are used for wireless mouse operation. (Refer to page 41.)
The Wireless mouse is usable when PC mouse pointer is displayed on the screen. The wireless mouse cannot
be used when the On-Screen Menu is displayed.
VIDEO BUTTON
Used to select
source. (P31)
ZOOM BUTTON
VIDEO
Used to adjust zoom. (P23)
POWER ON-OFF BUTTON
COMPUTER / MCI BUTTON
Used to select either the
COMPUTER source or the
MCI mode. (P25)
R/
PUTE
COM C I
M
VOLUM
E
VOLUME BUTTONS
VIDEO
ON-O
ZOOM
PAGE
FF
FOCUS
Used to adjust volume. (P24)
MUTE
FOCUS BUTTON
Used to adjust focus. (P23)
Used to turn the projector on
or off. (P22)
AUTO IM
AGE
CURSOR
MENU
FREE
NO S ZE/
HOW
NORM
AL
FREEZE / NO SHOW BUTTON
Used to stop the picture or to
turn the picture into black
image. (P23)
MUTE BUTTON
Used to mute sound. (P24)
AUTO IMAGE BUTTON
Use to operate AUTO IMAGE
function. (P 29)
PAGE BUTTON
Used to move to next or to
previous page of the data in
memory card. These buttons
are activated in MCI mode
only. (P34)
NORMAL BUTTON
LASE
R
M
D. ZOO
Used to reset to normal
picture adjustment preset by
the factory. (P29, 32)
CURSOR BUTTON
Used to display CURSOR on
the screen. (P23)
MENU BUTTON
Used to call MENU operation.
(P19)
POINT BUTTON
Used to select an item on the
MENU or to move cursor on
screen. It is also used to pan
the image in DIGITAL ZOOM
mode. (P30, 36)
D.ZOOM BUTTON
Used to turn the projector into
DIGITAL ZOOM mode.
(P30, 36.)
FRONT CLICK BUTTON
LASER BUTTON
Used to operate laser pointer
function. The laser beam is
emitted while pressing this
button.
Used as right button of PC mouse
in wireless mouse operation. It is
also used to compress the image in
DIGITAL ZOOM mode. (P30, 36)
SELECT BUTTON
Used to execute the item selected, or to
increase or decrease the values in
certain items such as CONTRAST or
BRIGHTNESS. It is also used to expand
the image in DIGITAL ZOOM mode.
(P30, 36)
LASER POINTER button
This remote control emits a laser beam as the Laser Pointer from the Laser Light Window. When the LASER button is pressed, the laser
light goes on: When the button is released, light goes off. Laser light is emitted with the RED light which tells the laser beam being emitted.
The laser emitted is a class II laser; therefore, do not look into the Laser Light Window or shine the laser beam on yourself or other people. The three marks
to the right are the caution labels for the laser beam.
CAUTION : Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
These caution labels are put on the remote control.
Laser Light Window
16
BEFORE OPERATION
Remote Control Batteries Installation
1
Remove the battery
compartment lid.
2
Slide the batteries into
the compartment.
3
Replace the compartment
lid.
Press the lid
downward and
slide it.
Slide the lid
upward.
For correct polarity (+ and –), be sure
the battery terminals are in contact
with the pins in the compartment.
To insure safe operation, please observe the following precautions :
● Use (2) AA type alkaline batteries.
● Replace two batteries at the same time.
● Do not use a new battery with a used battery.
● Avoid contact with water or liquid.
● Do not drop the remote control unit.
● If batteries have leaked on the remote control, carefully wipe the case clean and load new batteries.
Operating Range of the Remote Control
Point the remote control toward the projector (Receiver Window) whenever pressing the buttons. Maximum
operating range for the remote control is about 16.4’ (5m) and 60° front and rear of the projector.
16.4'
(5 m)
60°
16.4'
(5 m)
60°
17
BEFORE OPERATION
TOP CONTROLS AND INDICATORS
LAMP INDICATOR
This indicator is lit in dimly lit
when the projector is turned
on. And the light is brightly lit
when the projector is in standby mode.
MENU BUTTON
Used to active or terminate the
MENU operation.
(Refer to P19.)
LAMP REPLACE INDICATOR
WARNING TEMP. INDICATOR
This indicator turns to yellow
when the life of the projection
lamp draws to an end.
(Refer to P43.)
This indicator flashes red
when internal projector
temperature is too high.
(Refer to P42.)
READY INDICATOR
This indicator lights in green
when the projector is ready to
be turned on.
POWER ON–OFF BUTTON
LAMP REPLACE
WARNING TEMP.
LAMP
Used to turn the projector on
or off. (Refer to P22.)
READY
MENU
ON–OFF
POINT BUTTONS
AUTO IMAGE BUTTON
Used to operate AUTO IMAGE
function.
(Refer to P29.)
Used to move the pointer.
(Refer to P19.)
SELECT
NORMAL
AUTO IMAGE
FOCUS BUTTON
Used to select focus adjust.
(Refer to P23.)
FOCUS
+
PAGE
ZOOM
18
VOLUME
–
PAGE BUTTONS
Used to move to the next /
previous page of the data in
the memory card plugged into
PC CARD SLOT. These
buttons are used to stop or
resume AUTO-PLAY function.
Page buttons are activated in
MCI mode only.
(Refer to P34.)
MODE
SELECT BUTTON
Used to execute the item
selected or to adjust the values
in certain items on the MAIN
MENU DISPLAY.
NORMAL BUTTON
Used to reset to normal picture
adjustment preset by factory.
(Refer to P29 and 32.)
VOLUME BUTTONS
ZOOM BUTTON
Used to select zoom
adjustment.
(Refer to P23.)
MODE BUTTON
Used to select input source.
(Computer, Video and MCI)
(Refer to P25 and 31.)
Used to adjust volume.
(Refer to P24.)
BEFORE OPERATION
OPERATING ON-SCREEN MENU
HOW TO OPERATE ON-SCREEN MENU
You can control and adjust this projector through ONSCREEN MENU. Refer to the following pages to operate
the each adjustment on the ON-SCREEN MENU.
WIRELESS REMOTE CONTROL
POINT BUTTON
Used to move the
Pointer to UP/ DOWN/
RIGHT/ LEFT.
1 MOVING THE POINTER
Move the pointer (see the NOTE below) by pressing POINT
button(S) on the TOP CONTROL or the REMOTE CONTROL.
SELECT BUTTON
Used to select the item.
2 SELECT THE ITEM
Select the item by pressing SELECT button.
TOP CONTROL
SELECT BUTTON
Used to select the item.
NOTE :The Pointer is the icon on the ON-SCREEN Menu
to select the item. See the figures on the section
"FLOW OF ON-SCREEN MENU" below.
SELECT
POINT BUTTON
Used to move the Pointer
to UP/ DOWN/ RIGHT/
LEFT.
FLOW OF ON-SCREEN MENU
Display ON-SCREEN MENU
1
Press MENU button to display the ON-SCREEN MENU (MENU
BAR). The red frame is the POINTER.
MENU BAR
Select the MENU
2
Move the POINTER (red frame) to the ITEM ICON that you want
to select by pressing POINT RIGHT/ LEFT buttons.
3
Select the ITEM by pressing SELECT button. The dialog box of
the ITEM appears.
POINTER
(red frame)
SELECT
BUTTON
ITEM ICON
Control and adjust through ON-SCREEN MENU
4
Move the POINTER downward by pressing POINT DOWN button.
(The shape of POINTER become an arrow.)
5
Move the POINTER to the ITEM that you want to adjust and
adjust the ITEM by pressing SELECT button.
Refer to the following pages for details of respective adjustments.
POINTER
(red frame)
MENU
POINT
DOWN
BUTTON
POINTER
(arrow)
19
BEFORE OPERATION
MENU BAR
MENU BAR IN COMPUTER MODE
MODE MENU
Used to select
the Computer
input mode.
(Refer to P25)
AUTO IMAGE MENU
PC ADJUST MENU
SETTING MENU
Used to adjust Fine
sync., Total dots,
and Picture Position
automatically.
(Refer to P29)
Used to adjust the
parameters to
match with the input
signal format.
(Refer to P26)
Used to set the Display
Menu and to reset
Lamp Replacement
Monitor Timer.
(Refer to P40)
LANGUAGE MENU
Used to select
the language
used in the Menu.
(Refer to P40)
SYSTEM MENU
IMAGE MENU
POSITION MENU
SCREEN MENU
SOUND MENU
Used to select a
computer
system.
(Refer to P25)
Used to adjust the
computer image. [Fine
sync. / Total dots /
White Balance /
Contrast / Brightness]
(Refer to P28)
Used to adjust
the position of
the image.
(Refer to P30)
Used to adjust the
size of the image.
(Refer to P30)
Used to adjust
the Sound
Volume, or to
select Mute.
(Refer to P24)
MENU BAR IN VIDEO MODE
Press MENU BUTTON while being in Video mode.
MODE MENU
IMAGE MENU
Used to select
the Video input.
(Refer to P31)
Used to adjust the
picture image. [Color /
Tint / Contrast /
Brightness/ Sharpness]
(Refer to P32)
These icons have the
same function as the
Computer Mode.
SYSTEM MENU
SCREEN MENU
Used to select a color
system [PAL, SECAM,
Used to set the size
of the image
[Regular, Wide].
(Refer to P32)
NTSC, NTSC 4.43, PALM].
(Refer to P31)
20
Press MENU BUTTON while being in Computer mode.
BEFORE OPERATION
MENU BAR IN MCI MODE
Press MENU BUTTON while being in MCI mode.
MODE MENU
IMAGE MENU
Used to select
the MCI input
mode.
(Refer to P34)
Used to adjust the
computer image. [Fine
sync. / Total dots /
White Balance /
Contrast / Brightness]
(Refer to P35)
These icons have the
same function as the
Computer Mode.
VIEW MENU
POSITION MENU
SCREEN MENU
Used to display, read
or write the image data
in a memory card
through the PC CARD
SLOT.
(Refer to P34, 37)
Used to adjust
the position of
the image.
(Refer to P36)
Used to adjust
the size of the
image.
(Refer to P36)
21
BASIC OPERATIONS
TURNING ON / OFF THE PROJECTOR
Turning on the Projector
1
Complete the peripheral connections (with Computer, VCR, and
etc.) before turning on the projector. (Refer to "CONNECTING TO
THE PROJECTOR" on Pages 10~15 for connecting equipment.)
2
Connect the projector's AC power cord into a wall outlet. The
LAMP POWER indicator lights RED, and the READY indicator
lights GREEN.
3
Press the power ON-OFF button on the Remote Control Unit or on
the Top Control to ON. The LAMP POWER indicator dims, and
the Cooling Fans start to operate. The Preparation Display
appears on the screen and the count-down starts. The signal
from the source appears after 30 seconds.
30
The Preparation Display disappears after 30 seconds.
Turning off the Projector
1
Press the power ON-OFF button on the Remote Control Unit or on
the Top Control, and the message "Power off?" appears on the
screen.
2
Press the power ON-OFF button again to turn off the projector.
The LAMP POWER indicator brightens and the READY indicator
turns off. The Cooling Fans operate for 90 seconds after the
projector is turned off. (During this "Cooling Down" period, this
appliance cannot be turned on.)
3
Power off?
The message disappears after 4 seconds.
When the cooling of the projector has finished, the READY
indicator turns to green again and you can turn the projector on.
To power down completely, disconnect the AC power cord.
TO MAINTAIN THE LIFE OF THE LAMP, ONCE YOU TURN IT ON, WAIT AT LEAST 5 MINUTES
BEFORE TURNING IT OFF.
When the TEMPERATURE WARNING indicator flashes red, the projector is automatically turned off.
Wait at least 5 minutes before turning the projector on again.
If the TEMPERATURE WARNING indicator continues to flash, follow procedures below:
1. Press the power ON-OFF button to OFF.
2. Check the air filters for dust accumulation.
3. Remove dust with vacuum cleaner. (See "AIR FILTER CARE AND CLEANING" section on page 46.)
4. Press the power ON-OFF button to ON.
If the TEMPERATURE WARNING indicator still continues to flash, call Boxlight or an authorized Boxlight
dealer.
NOTE : The Cooling Fan may work for cooling while the projector is turned off. When the Cooling Fan is
working, TEMPERATURE WARNING INDICATOR flashes red.
22
BASIC OPERATION
ADJUSTING THE IMAGE
ZOOM Adjustment
1
Press ZOOM button on the Top Control or the Remote Control to
turn into the ZOOM mode.
2
Adjust the size of the image by pressing POINT UP/DOWN
button.
Press UP button to make the image larger, and press DOWN
button to make the image smaller.
ZOOM
The message disappears after 4 seconds.
FOCUS Adjustment
1
Press FOCUS button on the Top Control or the Remote Control to
turn into the FOCUS mode.
2
Adjust the focus of the image by pressing POINT UP or DOWN
button.
FOCUS
The message disappears after 4 seconds.
PICTURE FREEZE / NO SHOW FUNCTION
Press the FREEZE / NO SHOW button on the Remote Control Unit to
freeze the picture or turn the picture into a black image. This function is
cancelled when the FREEZE / NO SHOW button is pressed again or
any other function button is pressed.
NORMAL mode
FREEZE mode
NO SHOW mode
CURSOR FUNCTION
This projector can display a cursor by pressing cursor button on the
Remote Control. The cursor can be controlled with the POINT buttons.
To terminate the Cursor Function, press CURSOR button again.
NOTE : The cursor settings set with the “Media Card Imager” is not
available in this projector.
Cursor
23
BASIC OPERATION
SOUND ADJUSTMENT
Direct Operation
It indicates the roughly
level of the volume.
Sound Volume Adjustment
Press the VOLUME (+/–) buttons (located on the Top Control or on the
Remote Control Units) to adjust the volume. The Volume dialog box
appears on the screen for a few seconds.
Use (+) button to increase the volume, and (–) button to decrease the
volume.
Sound Mute Setting
Press the MUTE button on the Remote Control Units to cut off the
sound. To restore the sound to its previous level, press again or press
Volume buttons.
Press the MUTE button to set
the Mute function On or Off.
The display disappears after 4 seconds.
Menu Operation
1
Press the MENU button and the ON-SCREEN MENU will appear.
Press the POINT LEFT/RIGHT buttons to select SOUND
and press the SELECT button. Another dialog box SOUND
ADJUST Menu will appear.
2
Press the POINT DOWN button and a red-arrow icon will appear.
Move the arrow to the item that you want to select by pressing the
POINT UP/DOWN buttons.
Volume
Mute
24
Move the arrow to ▲ or ▼ of "Volume" by pressing the
POINT UP/ DOWN buttons. To increase the volume,
point the arrow to ▲ and then press the SELECT button.
To decrease the volume point the arrow to ▼ and then
press the SELECT button.
To cut off the audio sound, point the arrow to "Mute" and
then press the SELECT button. The Mute display is
changed On from Off and the sound is cut off. To restore
the sound to its previous volume level, set the Mute to
Off.
It indicates roughly
the level of the item.
Move the arrow to
the item and then
press the SELECT
button.
Move the arrow to ▲
or ▼ and press the
SELECT button.
It closes the
Sound Menu.
COMPUTER MODE
SELECTING COMPUTER MODE
Direct Operation
Press the MODE button on the Top Control or the COMPUTER / MCI
button on Remote Control Unit. Select the Mode among COMPUTER,
VIDEO, or MCI mode.
MODE button
COMPUTER / MCI
button
COMPUTER
COMPUTER
MCI
MCI
VIDEO
Menu Operation
Press the MENU button and the ON-SCREEN MENU will appear.
Press the POINT LEFT/RIGHT buttons to select Computer
and
press the SELECT button.
CURRENT MODE DISPLAY
When selecting the Computer Mode, the Current Mode display appears.
It shows the information of the computer as detected by the projector.
This column provides the
information of the computer
detected by the projector.
SELECTING COMPUTER SYSTEM
Automatic Multiscanning system
This projector automatically adapts to most types of computers based
on VGA, SVGA or XGA (refer to "COMPATIBLE COMPUTER
SPECIFICATIONS" on page 27). When selecting Computer, this
projector automatically detects the incoming signal and projectors the
proper image without any special setting. (Setting of the Computer
System may be required when connecting some computers.)
Note : The projector may provide the messages below.
SYSTEM BOX
It displays the SYSTEM
being selected.
Go PC adj. The projector cannot discriminate or detect the input
signal from the computer. Adjust and set the computer
system manually. (Refer to page 26.)
No signal
There is no signal input from the computer. Make sure
the connection of the computer and the projector is set
correctly. (Refer to TROUBLESHOOTING on page 44.)
The system being selected.
Selecting Computer System Manually
To set the Computer system manually, select the computer mode on
the ON-SCREEN MENU.
1
2
Press the MENU button and the ON-SCREEN MENU will appear.
Press the POINT LEFT/RIGHT buttons to select SYSTEM and
press the SELECT button. Another dialog box COMPUTER
MODE Menu will appear. (The COMPUTER MODE Menu also
appears by pressing the SYSTEM button on the Top Control or
the Remote Control Units.)
Press the POINT DOWN button and a red-arrow icon will appear.
Move the arrow to the system that you want to set, and then press
the SELECT button.
The systems on this
dialog box can be
selected.
When this mark is
displayed as black, more
computer system modes
will be available. Move
the arrow to this mark and
then press the SELECT
button, and another mode
will be displayed.
It closes the
SYSTEM Menu.
25
COMPUTER MODE
PC ADJUSTMENT
This Projector can automatically detect display signals from most personal computers currently distributed.
However, some computers employ special signal formats which are different from the standard ones and may
not be detected by this projector. If this happens, the projector cannot reproduce a proper image and the image
is recognized as a flickering picture, a non-synchronized picture, a non-centered picture or a skewed picture.
This projector has PC ADJUSTMENT function, to enable you to precisely adjust several parameters to match with the input
signal format. The projector has eight independent memory areas where you can store the parameter you have set. This
enables you to recall the setting for a specific computer whenever you need it.
1
Press the MENU button and the ON-SCREEN MENU will appear.
Press the POINT LEFT/RIGHT buttons to select PC ADJUST
and press the SELECT button. Another dialog box "Where to
reserve" Menu will appear.
2
In this dialog box, you can store the parameter into the area from
"Mode 1" to "Mode 8." When memorizing the new computer
parameter, select the Mode with the message of "Free" by
pressing the POINT UP/DOWN buttons and SELECT button. To
change the parameters of the Mode previously set, select the
Mode with "Stored."
3
When the Mode is selected, Parameter adjustment dialog box
appears. Adjust each item to match your computer.
Total lines
The number of the total vertical lines. Adjust the number to
match your PC image.
Total dots
The number of the total dots in one horizontal period. Adjust the
number to match your PC image.
Horizontal
Adjustment of the horizontal picture position. When the image is
not centered on the screen, adjust this item.
Vertical
Adjustment of the vertical picture position. When the image is
not centered on the screen, adjust this item.
Clamp
Adjustment of the clamp level. When the image has a dark
bar(s), try this adjustment.
Height
Adjusting the vertical height of the picture image.
Width
Adjusting the horizontal width of the picture image.
4
When the parameter data adjustments are set, select "Stored" and
press the SELECT button. "OK?" dialog box is displayed for
confirmation.
Each of the keys operates as follow.
Reset
Mode free
Stored
Quit
5
26
Recalls the parameter data that was previously adjusted.
Clears the parameter data previously set in the selected
Mode.
Stores the parameters in the memory.
Closes the PC ADJUST Menu.
To select the Mode manually adjusted in PC ADJUSTMENT
Menu, select the mode at the SYSTEM SELECT Menu. (Refer to
page 25.)
Stored
Stored
When the Mode is
selected, the dialog
box shown below
appears.
This Mode has
parameters already
stored.
The Vacant Mode.
Manual set Computer
Mode (1 to 8).
It closes the PC
ADJUSTMENT
Menu.
Move the arrow to
▲ or ▼ and press
SELECT button.
Press SELECT
button at this item
to adjust “Clamp,”
“Display area,”
“Horiz. scale,” or
“Vert. scale.”
COMPUTER MODE
COMPATIBLE COMPUTER SPECIFICATIONS
Basically this projector can accept the signal from all computers with the V and H-Frequency listed below
mentioned and less than 135 MHz of Dot Clock.
V-Freq.
(Hz)
59.88
ON-SCREEN
DISPLAY
RESOLUTION
640 x 480
H-Freq.
(kHz)
31.47
XGA 5
VGA 2
720 x 400
31.47
70.09
VGA 3
640 x 400
31.47
VGA 4
640 x 480
37.86
ON-SCREEN
DISPLAY
RESOLUTION
VGA 1
1024 x 768
H-Freq.
(kHz)
60.31
V-Freq.
(Hz)
74.92
XGA 6
1024 x 768
48.50
60.02
70.09
XGA 7
1024 x 768
44.00
54.58
74.38
XGA 8
1024 x 768
63.48
79.35
36.00
43.59
VGA 5
640 x 480
37.86
72.81
XGA 9
1024 x 768
(Interlace)
VGA 6
640 x 480
37.50
75.00
XGA 10
1024 x 768
62.04
77.07
VGA 7
640 x 480
43.269
85.00
XGA 11
1024 x 768
61.00
75.70
35.522
43.48
MAC LC13
640 x 480
34.97
66.60
XGA 12
1024 x 768
(Interlace)
MAC 13
640 x 480
35.00
66.67
XGA 13
1024 x 768
46.90
58.20
MAC1 6
832 x 624
49.72
74.55
XGA 14
1024 x 768
47.00
58.30
MAC 19
1024 x 768
60.24
75.08
XGA15
1024 x 768
58.03
72.0
MAC21
1152 x 870
68.68
75.06
SXGA 1
1152 x 864
64.20
70.40
MAC
1280 x 960
75.00
75.08
SXGA 2
1280 x 1024
62.50
58.60
MAC
1280 x 1024
80.00
75.08
SXGA 3
1280 x 1024
63.90
60.00
RGB
15.625
25
SXGA 4
1280 x 1024
63.34
59.98
RGB
768 x 576
(Interlace)
640 x 480
(Interlace)
15.734
30
SXGA 5
1280 x 1024
63.74
60.01
SVGA 1
800 x 600
35.156
56.25
SXGA 6
1280 x 1024
71.69
67.19
SVGA 2
800 x 600
37.88
60.32
SXGA 7
1280 x 1024
81.13
76.107
SVGA 3
800 x 600
46.875
75.00
SXGA 8
1280 x 1024
63.98
60.02
SVGA 4
800 x 600
53.674
85.06
SXGA 9
1280 x 1024
79.976
75.025
SVGA 5
800 x 600
48.08
72.19
SXGA 10
1280 x 960
60.00
60.00
SVGA 6
800 x 600
37.90
61.03
SXGA 11
1152 x 900
61.20
65.20
SVGA 7
800 x 600
34.50
55.38
SXGA 12
1152 x 900
71.40
75.60
50.00
43.00
50.00
47.00
SVGA 8
800 x 600
38.00
60.51
SXGA 13
SVGA 9
800 x 600
38.60
60.31
SXGA 14
1280 x 1024
(Interlace)
1280 x 1024
(Interlace)
SVGA 10
800 x 600
32.70
51.09
SXGA 15
1280 x 1024
63.37
60.01
SVGA 11
800 x 600
38.00
60.51
SXGA 16
1280 x 1024
76.97
72.00
XGA 1
1024 x 768
48.36
60.00
SXGA 17
1152 x 900
61.85
66.00
46.43
43.35
XGA 2
1024 x 768
68.677
84.997
SXGA 18
1280 x 1024
(Interlace)
XGA 3
1024 x 768
60.023
75.03
SXGA 19
1280 x 1024
63.79
60.18
XGA 4
1024 x 768
56.47
70.07
SXGA 20
1280 x 1024
91.146
85.024
NOTE : Specifications are subject to change without notice.
27
COMPUTER MODE
PICTURE IMAGE ADJUSTMENT
Adjust Picture Image Manually
1
Press the MENU button and the ON-SCREEN MENU will appear.
Press the POINT LEFT/RIGHT buttons to select IMAGE
and
press the SELECT button. Another dialog box PICTURE IMAGE
ADJUSTMENT Menu will appear.
2
Press the POINT DOWN button and a red-arrow icon will appear.
Move the arrow to ▲ or ▼ of the item that you want to change by
pressing the POINT UP/DOWN buttons. To increase the value,
point the arrow to ▲ and then press the SELECT button. To
decrease the value point the arrow to ▼ and then press the
SELECT button.
Fine sync
It indicates the
roughly level of
the item.
Adjust the picture as necessary to eliminate flicker from the display.
(From 0 to 127.) This item can be adjusted by pressing the FINE
SYNC. button on the Top Control or the Remote Control Unit.
Total dots
The number of the total dots in one horizontal period. Adjust the
number to match your PC image.
Move the arrow to
▲ or ▼ and press
the SELECT
button.
White Balance (Red / Green / Blue)
Point to ▼ to lighten the color of the image, and select ▲ to deepen
the color of the image. (From 0 to 63.)
Contrast
Point to ▼ to make the image lighter, and select ▲ to make the image
deeper. (From 0 to 63.)
Brightness
Point to ▼ to make the image darker, and select ▲ to make the image
brighter. (From 0 to 63.)
Each of the keys operates as follow.
Reset
Recalls the data previously adjusted.
Stored
Stores the adjusted data in the memory.
Quit
28
Closes the PICTURE IMAGE ADJUSTMENT Menu.
It closes the PICTURE
IMAGE ADJUSTMENT
Menu.
COMPUTER MODE
Auto Image Function
The Auto Image function is provided to automatically adjust Fine sync.,
Total dots, and Picture Position for most computers.
1
Press the MENU button and the ON-SCREEN MENU will appear.
Press the POINT LEFT/RIGHT buttons to select AUTO IMAGE
and press the SELECT button.
Another dialog box AUTO IMAGE Menu will appear.
2
Move the arrow to an item that you want to adjust by pressing the
POINT UP/DOWN button. Change the setting On or Off by
pressing the SELECT button.
Fine sync
Adjust the picture as necessary to eliminate flicker from
the display. This item can be adjusted manually. (Refer
to page 28.)
Total Dots
The number of the total dots in one horizontal period.
This item can be adjusted manually. (Refer to page 28.)
Position
3
Move the arrow to
the item and then
press the
SELECT button.
It starts the adjustment on the item
set to "On".
Adjustment of the position of the image. This item can
be adjusted manually. (Refer to page 30.)
It closes the PICTURE
IMAGE ADJUSTMENT
Menu.
Move the arrow to "Go!" and press the SELECT button to start the
Auto Image function.
This adjustment can be executed by pressing AUTO IMAGE
button on the Top Control and the Remote Control.
NOTE : The Fine sync., Total dots, and Picture Position of some
computers may not be fully adjusted with the Auto Image
Function. In that case, manual adjustments are required to
correct the image. (Refer to PICTURE IMAGE ADJUSTMENT
on page 28 to adjust "Fine sync." or "Total dots" and PICTURE
POSITION ADJUSTMENT on page 30 to adjust Picture
Position.)
Normal Function
The normal picture level is preset on this projector by the factory and
can be restored anytime by pressing the NORMAL button (located on
the Top Control or on the Remote Control Unit). The "Normal" display
will be displayed on the screen for a few seconds.
Normal
29
COMPUTER MODE
PICTURE POSITION ADJUSTMENT
The position of the image can be adjusted vertically and horizontally through PICTURE POSITION
ADJUSTMENT.
1
Press the MENU button and the ON-SCREEN MENU will appear.
Press the POINT LEFT/RIGHT buttons to select POSITION
and press the SELECT button. Another dialog box PICTURE
POSITION Menu will appear.
2
Select the arrow to the direction (described as
,
,
or
)
that you want to adjust by pressing the POINT UP/DOWN buttons,
and then press the SELECT button.
Each of the keys operates as follow.
Reset
Recalls the setting data previously set.
Stored
Stores the setting data in the memory.
Quit
Select the arrow to the
direction (described as
,
,
or
),and
then press the SELECT
button.
Closes the PICTURE POSITION Menu.
PICTURE SCREEN ADJUSTMENT
This projector has a picture screen resize function, which enables you to display the image in desirable size.
1
Press the MENU button and the ON-SCREEN MENU will appear.
Press the POINT LEFT/RIGHT buttons to select SCREEN
and press the SELECT button. Another dialog box PICTURE
SCREEN Menu will appear.
2
To adjust the image size or pan the image, move the arrow to
Digital zoom by pressing POINT UP/DOWN buttons and then
press SELECT button. The ON-SCREEN menu and SCREEN
ADJUST menu will disappear. The magnifying-glass icon and the
message “D. Zoom” is displayed to indicate Digital Zoom mode.
3
To cancel Digital Zoom mode, press any other button except
SELECT / FRONT CLICK / POINT / LASER / CURSOR buttons.
To adjust the image to the screen size (1024 x 768), press
NORMAL button.
4
To return the image to its original size select True in the dialog
box. When the original image size is larger than the screen size
(1024 x 768), this projector engages the Digital Zoom mode
automatically.
Move the arrow to
“Digital zoom” or “True”
and then press the
SELECT button.
Expand function
To expand the image size, press SELECT button. The image is magnified by degrees. The maximum size of the
projected image in expand mode is 4 times as large as the screen size (1024 x 768).
Compress function
To compress the image size, press FRONT CLICK button. The size of image is reduced by degrees. The minimum
size of the projected image in compress mode is 640 x 480 in VGA, 800 x 600 in SVGA, or 1024 x 768 in XGA /
SXGA.
Panning function
To pan the image, press POINT UP/DOWN/LEFT/RIGHT buttons. Panning function can work only when the image is
larger than the screen size.
● This projector cannot display in a resolution more than 1280 X 1024. If your computer’s screen resolution is higher than
1280 X 1024, set the resolution lower before connecting the projector.
● The image data in other than XGA (1024 x 768) is modified to fit the screen size in the initial mode.
● The normal "Panning Operation" may not function properly if the "PC Adjust" is used to lock the computer signal.
30
VIDEO MODE
SELECTING VIDEO MODE
Direct Operation
Press the MODE button on the Top Control or the VIDEO button on the
Remote Control Unit. Select the Mode among COMPUTER, VIDEO, or
MCI mode.
MODE button
COMPUTER
MCI
VIDEO
Menu Operation
Press the MENU button and the ON-SCREEN MENU will appear.
Press the POINT LEFT/RIGHT buttons to select Video
and press
the SELECT button.
SELECTING COLOR SYSTEM
1
Press the MENU button and the ON-SCREEN MENU will appear.
Press the POINT LEFT/RIGHT buttons to select SYSTEM and
press the SELECT button. Another dialog box VIDEO SYSTEM
Menu will appear. (The display also appears by pressing the
SYSTEM button on the Top Control or the Remote Control Units.)
2
Press the POINT DOWN button and a red-arrow icon will appear.
Move the arrow to "Auto", and then press the SELECT button.
Auto
This box indicates
the system being
selected.
The projector automatically detects the incoming Video system, and
adjusts itself to optimize its performance.
When the Video System is PAL-M select the system manually.
PAL / SECAM / NTSC / NTSC4.43 / PAL-M
If the projector cannot reproduce the proper video image, it is
necessary to select a specific broadcast signal format among PAL,
SECAM, NTSC, NTSC 4.43, or PAL-M.
31
VIDEO MODE
PICTURE IMAGE ADJUSTMENT
Adjusting the Picture Image
1
Press the MENU button and the ON-SCREEN MENU will appear.
Press the POINT LEFT/RIGHT buttons to select IMAGE
and
press the SELECT button. Another dialog box PICTURE IMAGE
ADJUSTMENT Menu will appear.
2
Press the POINT DOWN button and a red-arrow icon will appear.
Move the arrow to ▲ or ▼ of the item that you want to change by
pressing the POINT UP/DOWN buttons. To increase the value,
point the arrow to ▲ and then press the SELECT button. To
decrease the value point the arrow to ▼ and then press the
SELECT button.
Color
Point to ▼ to lighten the image, and select ▲ to deepen
the image. (From 0 to 63.)
Tint
Point to ▼ to adjust the color more purple, and select ▲
to adjust more green. (From 0 to 63.)
Contrast
Point to ▼ to lighten the image, and select ▲ to deepen
the image. (From 0 to 63.)
Brightness
Point to ▼ to darken the image, and select ▲ to
brighten the image. (From 0 to 63.)
sharpness
Point to ▼ to soften the image, and select ▲ to make
the image sharper. (From 0 to 63.)
It indicates roughly
the level of the
item.
Move the arrow to
▲ or ▼ and press
the SELECT
button.
It closes the PICTURE
IMAGE ADJUSTMENT
Menu.
Each of the keys operates as follow.
Reset
Recalls the data previously adjusted.
Stored
Stores the data in the memory.
Quit
Closes the PICTURE IMAGE ADJUSTMENT Menu.
Normal Function
The normal picture level is preset on this projector by the factory and
can be restored anytime by pressing the NORMAL button (located on
the Top Control or on the Remote Control). The "Normal" display will
be displayed on the screen for a few seconds.
Normal
PICTURE SCREEN ADJUSTMENT
This projector has a picture screen resize function, which enables you to display the image in desirable size.
1
Press the MENU button and the ON-SCREEN MENU will appear.
Press the POINT LEFT/RIGHT buttons to select SCREEN
and press the SELECT button. Another dialog box PICTURE
SCREEN ADJUSTMENT DISPLAY will appear.
2
Press the POINT DOWN button and a red-arrow icon will appear.
Move the arrow to the screen size that you want to set, and then
press the SELECT button.
Regular
Wide
32
Normal Video Image size with 4 x 3 aspect ratio.
Compresses the image vertically to Wider Video Image
size with 16 x 9 aspect ratio.
Move the pointer to the
item that you want to
select, and then press
the SELECT button.
MCI MODE
OPERATING THE PC CARD SLOT
This projector has a PC CARD SLOT on its side. Pictures in a memory card (SmartMedia with PC Card Adapter
or PC card) can be displayed just by inserting the card into PC CARD SLOT. It is unnecessary to connect with
other input equipment. Media Card Imager (supplied with CD-ROM) can edit the image data and record it into a
memory card for projecting with the projector.
PC with Windows 95
Media Card Imager
(CD-ROM)
PC Card or
SmartMedia
(with Adapter)
Digital Camera
SmartMedia (with Adapter)
PC CARD SLOT
Available Data
This projector can project the image data as follows through the PC CARD SLOT.
● The data edited by “Media Card Imager.”
● The data of the resolution between VGA (640 X 480) and SXGA (1280 X 1024) in Bit Map type (BMP) or JPEG type
(JPG), such as Digital Camera data, can be also displayed.
(Some image data in SXGA size may not be displayed properly. In that case, set the resolution lower.)
Refer to “SHOW THE DATA IN THE MEMORY CARD” on page 34 to display the image data.
Available Card
SmartMedia (with PC Card Adapter) or Type || PCMCIA-ATA Card can be used with this projector. Refer to
SMARTMEDIA AND PC CARD ADAPTER on pages 38 and 39 for operation.
NOTE : Some PCMCIA Adapter or PC Card are not compatible with for this projector and cannot provide the image data.
In that case, use our SmartMedia and PC Card Adapter.
How to Load a PC Card Into the Projector
LOAD
Insert PC Card Adapter (with SmartMedia) or PC card into PC
CARD SLOT. Make sure EJECT button pops out.
NOTE : Do not insert the card in the reverse. The card can be
damaged.
PC CARD SLOT
PC Card or PC Card Adapter
(with SmartMedia)
FRONT SIDE UP
UNLOAD
Press EJECT button, and the memory card pops out.
NOTE : Do not take the card out while the PC CARD SLOT
loading. Data and the card can be damaged.
EJECT BUTTON
Media Card Imager
Media Card Imager (CD-ROM) is attached to this projector
to edit the image data for projecting. Installation of Media
Card Imager is recommended. Refer to Owner’s Manual of
Media Card Imager for installation and operation.
PC CARD INDICATOR
DO NOT REMOVE THE
MEMORY CARD WHILE THIS
INDICATOR IS LIT. THE DATA
IN THE MEMORY CARD CAN
BE DAMAGED.
33
MCI MODE
SHOW THE DATA IN THE MEMORY CARD
Display Data on Screen
1
When the memory card is inserted into the PC CARD SLOT, mode is automatically set to MCI mode and the first
Page of the latest Index is projected on the screen. (To turn Video/Computer mode to MCI mode manually, press the
MODE button on the Top Control or the COMPUTER / MCI button on the Remote Control, or select MCI mode in the
ON-SCREEN MENU referring the page 25.)
2
To change the page, press PAGE ( ) or ( ) buttons. To select described Index or Page in the table, follow the
instructions of INDEX SELECTION and PAGE SELECTION.
● This projector can project only the image data edited with Media Card Imager or the data in Bit Map type or in JPEG
type through the PC CARD SLOT. Other data is not compatible and should be edited and written in a memory card
with Media Card Imager before loading PC CARD SLOT.
(The data in Bit Map type or in JPEG type, such as the data captured with a digital camera, can be projected directly
through PC CARD SLOT.)
● If there exists the data edited with Media Card Imager and other data (such as in Bit Map type or JPEG type) together
in a memory card, the data edited by Media Card Imager has priority to be projected with the LCD projector. The other
image data in Bit Map type or JPEG type is not projected. In that case, edit those data and record in the memory card
with Media Card Imager.
Index and Page
The data edited with Media Card Imager is organized into an Index consisting of several Pages. To project the Page,
select the Index and then select the Page in the Index.
Index Selection
1
Press the MENU button and the ON-SCREEN MENU will appear.
Press the POINT LEFT/RIGHT buttons to select VIEW and press
the SELECT button. Another dialog box VIEW SETTING menu
will appear.
2
Press the POINT DOWN button and a red-arrow icon will appear.
Move the arrow to "Index", and then press the SELECT button.
The table of Indexes in the memory card will appear.
3
Move the arrow to
▲ or ▼ and press
the SELECT
button.
Press POINT UP/DOWN/LEFT/RIGHT buttons to move to the
Index that you want to project and press SELECT button. The
first Page of the Index selected is displayed.
Press SELECT button again to display the table of Pages.
Select the Index
Page Selection
1
34
Press the MENU button and the ON-SCREEN MENU will appear.
Press the POINT LEFT/RIGHT buttons to select VIEW and press
the SELECT button. Another dialog box VIEW SETTING menu
will appear.
2
Press the POINT DOWN button and a red-arrow icon will appear.
Move the arrow to "Page", and then press the SELECT button.
The table of pages of the index card will appear.
3
Press POINT UP/DOWN/LEFT/RIGHT buttons to move to the
Page that you want to project and press SELECT button. The
page selected is displayed on the screen.
The table of Pages can be displayed by pressing SELECT button
when the page is displayed on full screen.
Index
Pages in the Index
MCI MODE
PICTURE IMAGE ADJUSTMENT
Adjust Picture Image Manually
1
Press the MENU button and the ON-SCREEN MENU will appear.
Press the POINT LEFT/RIGHT buttons to select IMAGE
and
press the SELECT button. Another dialog box PICTURE IMAGE
ADJUSTMENT Menu will appear.
2
Press the POINT DOWN button and a red-arrow icon will appear.
Move the arrow to ▲ or ▼ of the item that you want to change by
pressing the POINT UP/DOWN buttons. To increase the value,
point the arrow to ▲ and then press the SELECT button. To
decrease the value, point the arrow to ▼ and then press the
SELECT button.
It indicates roughly
the level of the
item.
Fine sync
Adjust the picture as necessary to eliminate flicker from the display.
(From 0 to 127.) This item can be adjusted by pressing the FINE
SYNC. button on the Top Control or the Remote Control Unit.
Move the arrow to
▲ or ▼ and press
the SELECT
button.
Total dots
The number of the total dots in one horizontal period. Adjust the
number to match your PC image.
White Balance (Red / Green / Blue)
Point to ▼ to lighten the color of image, and select ▲ to darken the the
color of the image deeper. (From 0 to 63.)
Contrast
It closes the PICTURE
IMAGE ADJUSTMENT
Menu.
Point to ▼ to make the image lighter, and select ▲ to make the image
darker. (From 0 to 63.)
Brightness
Point to ▼ to darken the image, and select ▲ to brighten the image.
(From 0 to 63.)
Each of the keys operates as follow.
Reset
Recalls the data previously adjusted.
Stored
Stores the adjusted data in the memory.
Quit
Closes the PICTURE IMAGE ADJUSTMENT Menu.
Normal Function
The normal picture level is preset on this projector by the factory and
can be restored anytime by pressing the NORMAL button (located on
the Top Control or on the Remote Control Units). The "Normal" display
will be displayed on the screen for a few seconds.
Normal
35
MCI MODE
PICTURE POSITION ADJUSTMENT
The position of the image can be adjusted vertically and horizontally through PICTURE POSITION
ADJUSTMENT.
1
Press the MENU button and the ON-SCREEN MENU will appear.
Press the POINT LEFT/RIGHT buttons to select POSITION
and press the SELECT button. Another dialog box PICTURE
POSITION Menu will appear.
2
Select the arrow to the direction (described as
,
,
or
)
that you want to adjust by pressing the POINT UP/DOWN buttons,
and then press the SELECT button.
Each of the keys operates as follow.
Reset
Recalls the setting data previously set.
Stored
Stores the setting data in the memory.
Quit
Select the arrow to the
direction (described as
,
,
or
),and
then press the SELECT
button.
Closes the PICTURE POSITION Menu.
PICTURE SCREEN ADJUSTMENT
This projector has a picture screen resize function, which enables you to display the image in desirable size.
1
Press the MENU button and the ON-SCREEN MENU will appear.
Press the POINT LEFT/RIGHT buttons to select SCREEN
and press the SELECT button. Another dialog box PICTURE
SCREEN Menu will appear.
2
To adjust the image size or pan the image, move the arrow to
Digital zoom by pressing POINT UP/DOWN buttons and then
press SELECT button. The ON-SCREEN menu and SCREEN
ADJUST menu will disappear. The magnifying-glass icon and the
message “D. Zoom” is displayed to indicate Digital Zoom mode.
3
To cancel Digital Zoom mode, press any other button except the
SELECT / FRONT CLICK / POINT / LASER / CURSOR buttons.
To adjust the image to the screen size (1024 x 768), press
NORMAL button.
4
To return the image to the screen size, select True in the dialog
box.
Move the arrow to
“Digital zoom” or “True”
and then press the
SELECT button.
Expand function
To expand the image size, press SELECT button. The image is magnified by degrees. The maximum size of the
projected image in expand mode is 4 times as large as the screen size (1024 x 768).
Compress function
To compress the image size, press FRONT CLICK button. The size of image is reduced by degrees. The minimum
size of the projected image in compress mode is 640 x 480 in VGA, 800 x 600 in SVGA, or 1024 x 768 in XGA /
SXGA.
Panning function
To pan the image, press POINT UP/DOWN/LEFT/RIGHT buttons. Panning function can work only when the image is
larger than the screen size.
● This projector cannot display in a resolution more than 1280 X 1024. If your computer’s screen resolution is higher than
1280 X 1024, set the resolution lower before connecting the projector.
● The image data in other than XGA (1024 x 768) is modified to fit the screen size in the initial mode.
36
MCI MODE
WRITE DATA INTO MEMORY CARD
The data edited by Media Card Imager in the computer can be written in or read from the memory card with the
PC or this projector.
The data edited by Media Card Imager is written in Bit Map type (BMP) or JPEG type (JPG).
Access to the Card with the Projector
If your computer doesn't have the PC card write equipment, the data can be written or read by connecting
with this projector.
NOTE : This operation can be made only by Media Card Imager in PC.
Connect the computer and the projector with MCI cable
(supplied) (refer to page 12, 13).
1
Connect the projector with your computer by the MCI cable
(supplied). (Refer to “CONNECTING COMPUTER” on Page 12.)
Insert the memory card into PC CARD SLOT of the projector.
And then, turn on the projector and the computer.
2
Press the MENU button and the ON-SCREEN MENU will appear.
Press the POINT LEFT/RIGHT buttons to select View and press
the SELECT button. Another dialog box VIEW SETTING Menu
will appear.
3
Press POINT DOWN button and a red arrow appear. Move the
arrow to Card access by pressing POINT UP/DOWN button. And
then press SELECT button. “Ready to access” is displayed.
Operate Media Card Imager of PC to write/read the data in the PC
card. (Refer to Owner's Manual of Media Card Imager for
operation.)
Move the arrow to
▲ or ▼ and press
the SELECT
button.
NOTE : Connect the projector to the computer with MCI Cable before
turning those appliances on.
Do not press any button while read/write the data through MCI
Cable. Those operations are canceled and the data in the
memory card may be damaged.
37
MCI MODE
SMARTMEDIA AND PC CARD ADAPTER
SmartMedia and PC Card Adapter are provided with this LCD projector. SmartMedia can be used as a PC card
conforming to the PC Card Standard-ATA by combining with PC Card Adapter.
Install / Remove the SmartMedia
INSTALL
Insert SmartMedia fully into PC Card Adapter. Make sure EJECT
button pops out.
NOTE
● The front side of SmartMedia has Contact Area on its surface.
The front side of PC Card Adapter has Eject button on the left
side of the slot.
● Do not insert SmartMedia in the reverse. The card and the
data can be damaged.
PC Card Adapter
(supplied)
SmartMedia
(supplied)
REMOVE
To remove SmartMedia, fully press in the EJECT button.
The card pops out, then take out the card.
NOTE
● Do not pull SmartMedia by force. It may damage SmartMedia
or PC Card Adapter.
①Contact Area
Data is written in Contact Area. Never
scratch or stain this area.
➁ Write Protect Area
Affix Write Protect Sticker onto Write
Protect Area to prevent from accidental
erasure.
➂ Index Area
Affix Index Label onto Index Area.
EJECT button
CAUTION
Write Protect Sticker is not available for PC. When PC attempts to read the data from SmartMedia with Write
Protect Sticker, it provides error messages or the control of PC becomes insecure because of the property of the
interface. When the error messages are displayed, press any key to return to the normal display. It is
recommended, therefore that the SmartMedia should be used on PC without Write Protect Sticker.
IMPORTANT NOTE
THE DATA STORED ON THE MEMORY CARD (SMARTMEDIA OR PC CARD) MAY BE DAMAGED OR
LOST BECAUSE OF THE DAMAGE OF THE MEMORY CARD OR THE ACCIDENTAL ERASURE. IT IS
RECOMMENDED THAT ANY IMPORTANT DATA SHOULD BE COPIED ONTO SEPARATE MEDIA,
SUCH AS A FLOPPY DISK, A HARD DISK, OR A MO DISK. WE SHALL NOT BE LIABLE FOR ANY
DAMAGE OR LOSS OF PROFITS ARISING FROM THE LOSS OF DATA BECAUSE OF THE
ACCIDENTAL OPERATION AND THE DAMAGE OF A MEMORY CARD OR APPLIANCES. REFER TO
OWNER’S MANUAL OF MEDIA CARD IMAGER FOR OPERATING THE SOFTWARE.
38
MCI MODE
Precautions and Specifications of the appliance.
SmartMedia
● SmartMedia is a precision device. Do not bend it,
drop it, subject it to strong forces or shocks or
place where strong static electrical charge can be
generated.
● Do not touch the surface of the Contact Area with
fingers or allow it to be stained with foreign materials. Store SmartMedia inside its protective case
when it is not used.
● SmartMedia is a consumable item. The data may
not be written in or read from SmartMedia by
using for a long time. In that case, replace
SmartMedia with new one.
Memory capacity : 8MB
Operating voltage : 3.3 V DC
Usage environment
Temperature : 0~55 °C (during use)
-20~65 °C (during storage)
Humidity : less than 95%
(during use, during storage)
PC Card Adapter
● Do not bend it, drop it, subject it to strong forces or
shocks or place where strong static electrical charge
can be generated.
● Do not insert materials other than SmartMedia. The
adapter may be damaged. Store PC Card Adapter
inside its protective case when it is not used.
● Do not shake the adapter, turn off the appliances, or
remove SmartMedia from the PC Card Adapter during writing or reading data. It may damage the data in
SmartMedia.
Operating voltage : 5 V DC
Usage environment
Temperature : 0~55 °C (during use)
-20~65 °C (during storage)
Humidity : less than 95%
(during use, during storage)
This adapter can be adapted to only our
SmartMedia indicated below.
Available SmartMedia
: 3.3V / 5V, 2MB / 4MB / 8MB /16MB
39
SETTING
SETTING MENU
1
Press the MENU button and the ON-SCREEN MENU will appear.
Press the POINT LEFT/RIGHT buttons to select SETTING
and press the SELECT button. Another dialog box
SETTING Menu will appear.
2
Press the POINT DOWN button and a red-arrow icon will appear.
Move the arrow to the item that you want to set, and then press
the SELECT button to set it "On" or "Off".
Blue back
When this function is in the "On" position, this projector
will produce a blue image without video noise on the
screen when the video source is unplugged or turned off.
Display
When this function is in the "On" position, the On-Screen
Displays always appear when adjustments are made.
(The following displays disappear by switching this
function "Off.")
● Preparation Display
Ceiling
(The Number-counting down Display)
Mode Display
Volume Display
Mute Display
Normal Display
When this function is in the “On” position, the top / bottom
and the left / right reversed picture is provided to project
the image from a ceiling mounted projector.
Rear
When this function is in the “On” position, the left / right
reversed picture is provided to project the image to a rear
projection screen.
Split wipe
When this function is in the “On” position, the picture will
change to the next one by sliding black image side ways
like drawing black curtains. This occurs when switching
from one input source to another.
Lamp age
The Lamp age function is designed to reset the lamp
replacement monitor timer. When replacing the lamp,
reset the lamp replacement monitor timer by using this
function. (Refer to page 43.)
T B
T B
●
●
●
●
Set the Pointer
to the item, and
then press the
SELECT button.
L
R
R
L
SETTING LANGUAGE
The language used in the ON-SCREEN MENU is selectable
from among English, German, French, Italian, Spanish and
Japanese.
1
2
40
Press the MENU button and the ON-SCREEN MENU will appear.
Press POINT LEFT/RIGHT buttons to select LANGUAGE and
press the SELECT button. Another dialog box LANGUAGE Menu
will appear.
Press the POINT DOWN button and a red-arrow icon will appear.
Move the arrow to the language that you want to set, and then
press the SELECT button.
Move the Pointer to the
language that you want
to set, and then press
the SELECT button.
APPENDIX
OPERATING WIRELESS MOUSE
The Wireless Remote Control Unit is not only able to operate the projector but can also be used as a wireless
mouse for a PC. POINT buttons and two CLICK buttons are used for wireless mouse operation.
Wireless mouse is usable when a PC mouse pointer is displayed on the screen. When the menu or indicator of
the projector is displayed on the screen instead of the PC mouse pointer, the wireless mouse cannot be used.
Installation
To use the Wireless Remote Control Unit as the Wireless Mouse for a PC, installation of the mouse driver (not
supplied) is required. Make sure that the mouse driver is properly installed in your computer. And make sure
that the mouse port of the computer connected to Control Port is activated.
1
Connect the mouse port of your computer to the Control
Port of the projector with the Mouse Cable. (Refer to
pages 14 and 15 for connection.)
2
Turn the projector on first, and then turn on your
computer. When the computer is switched on first, the
Wireless Mouse may not work properly.
Note : When the computer has no mouse
port, connect the Serial Port of the
computer to Control Port of the
projector with the Mouse Cable for
Serial Port.
Controlling Wireless Mouse
When controlling the pointer of the computer, operate the Wireless Mouse with POINT button, SELECT button,
and FRONT CLICK button on the Wireless Remote Control Unit.
POINT button
Used to move the pointer. The pointer is moved according to
the direction you are pressing.
POINT button
SELECT (REAR CLICK) button
This button has the same function as the left button on a PC
mouse.
FRONT CLICK
This button has the same function as the right button on a PC
mouse. Pressing this button dose not affect any operation
when in Menu mode.
SELECT button (Left mouse button)
FRONT CLICK button (Right mouse button)
41
APPENDIX
MAINTENANCE
TEMPERATURE WARNING INDICATOR
The TEMPERATURE WARNING Indicator flashes red when the internal temperature of the projector exceeds
the normal temperature. The Indicator stops flashing when the temperature of the projector become normal.
When the TEMPERATURE WARNING Indicator continues to flash, check the following.
1
The Ventilation slots of the projector are blocked. In such an event, reposition the appliance so that the ventilation
slots are not obstructed.
2
Air filter is clogged with dust particles. Remove dust from the air filter by following the instructions in the AIR FILTER
CARE AND CLEANING section below.
3
If the TEMPERATURE WARNING Indicator remains on after performing the above checks, the Cooling Fans or the
Internal Circuits may be malfunctioning. Contact Boxlight for service.
AIR FILTER CARE AND CLEANING
The Removable Air Filters prevent dust from accumulating on the surface of the Projection Lens and the
Projection Mirror. Should the Air Filters become clogged with dust particles, they will reduce the Cooling Fans'
effectiveness and may result in internal heat build up and effect on the life of the projector.
To clean the Air Filters, follow the cleaning procedures below:
1
Turn the power off, and disconnect the AC power cord from the
AC outlet.
2
Remove the air filter cover. Press the cover latch sideway and lift
the cover.
3
Remove the air filter from the filter cover.
4
Clean the air filter with a vacuum cleaner.
5
Replace the air filter. Make sure that the air filter cover is fully
inserted.
CAUTION
AIR FILTER
Do not operate the projector with the Air Filter removed. The
dust can become stuck on the LCD Panel and the Mirror, and
it may spoil the fine picture image.
RECOMMENDATION
We recommend avoiding dusty/smoky place for operating
the projector. Using in dusty places may cause poor quality
image.
When using under dusty or smoky conditions, dust may accumulate on the liquid crystal panel and lens inside, and may be projected on the screen together with the picture.
When the above symptoms are noticed contact Boxlight for
cleaning of the unit.
42
AIR FILTER COVER
APPENDIX
LAMP REPLACEMENT Indicator
When the Lamp of the projector draws to an end, the LAMP REPLACEMENT indicator lights yellow. When the
image become dark or the color of the image becomes unnatural, replacement of the Lamp is required.
Lamp Replacement
CAUTION
● For continued safety, replace with a lamp assembly of the same type.
● Allow the projector to cool for at least 45 minutes before you open the lamp cover. The inside of the projector
can become very hot.
● Do not drop the lamp assembly or touch the glass bulb! The glass can shatter and may cause injury.
Follow these steps to replace the lamp assembly.
1
Turn off the projector and disconnect the AC plug. Allow the
projector to cool for at least 45 minutes.
2
3
Remove the screw with a screwdriver and remove the lamp cover.
4
5
Replace the lamp assembly.
6
Connect the AC Power Cord to the projector and turn the projector
on.
7
Reset the Lamp Replacement Monitor Timer (refer to the section
“Lamp Replacement Monitor Timer” below.)
Remove 2 screws with a screwdriver and pull out the lamp
assembly by grasping the handle.
LAMP COVER
Replace the Lamp Assembly and tighten 2 screws. Make sure
that the Lamp Assembly is set properly. And replace the Lamp
Cover and tighten the screw.
HANDLE
NOTE : Do not reset the LAMP REPLACEMENT MONITOR
TIMER, when the lamp was not been replaced.
LAMP
ASSEMBLY
Lamp Replacement Monitor Timer
Be sure to reset the Lamp Replacement Monitor Timer when the Lamp Assembly is replaced. When the Lamp
Replacement Monitor Timer is reset, the LAMP REPLACEMENT indicator stops lighting.
1
Turn the projector on, and press the MENU button and the ON-SCREEN MENU will appear. Press the POINT
LEFT/RIGHT buttons to select SETTING
and press the SELECT button (refer to the page 40). Another
dialog box SETTING MENU Menu will appear.
2
Press the POINT DOWN button and a red-arrow icon will appear. Move the arrow to Lamp age, and then press the
SELECT button. The message of "Lamp replace monitor Reset?" is displayed.
3
Select [Yes] to reset the Timer.
Do not reset the Lamp Replacement Monitor Timer, except after the lamp has been replaced.
Cleaning the Projection Lens
Follow these steps to clean the projection lens:
1
Apply a non-abrasive camera lens cleaner to a soft, dry cleaning cloth. Avoid using an excessive amount of cleaner.
Abrasive cleaners, solvents or other harsh chemicals might scratch the lens.
2
3
Lightly wipe the cleaning cloth over the lens.
When you are not using the projector, replace the lens cover.
43
APPENDIX
TROUBLESHOOTING
Before calling your dealer or Boxlight for assistance, check the troubleshooting tips below.
1. Make sure you have connected the projector to your equipment as described in the section
"CONNECTING THE PROJECTOR" on pages 10 ~ 15.
2. Check cable connection. Verify that all computer, video and power cord are properly connected.
3. Verify that all power is switched on.
4. If the projector still does not produce the image, re-start the computer.
5. If the image still does not appear, unplug the projector from the computer and check the computer
monitor's display. The problem may be with your graphics controller rather than with the projector. (When
you reconnect the projector, remember to turn the computer and monitor off before your power up the
projector. Power the equipment on in their order of : Projector and computer.)
6. If the problem still exists, check with following chart.
Problem:
No power.
Try these Solution
● Plug the projector into the AC outlet.
● Be sure READY Indicator light is On.
● Wait one minute after the projector is turned OFF before turning the projector back
on.
NOTE : After pressing the power ON-OFF switch to OFF, make sure the projector
works as follow.
1. The LAMP indicator will light and the READY indicator will turn off.
2. After one minute, the READY indicator will light green again and the projector may
be turned on by pressing the power ON-OFF button.
● Check the TEMPERATURE WARNING indicator. If the indicator flashes red, the
projector cannot be turned on.
(See "TURNING ON/OFF THE PROJECTOR" section on page 22.)
● Check the Projection Lamp. (Refer to page 43.)
44
Image is out of
focus.
● Adjust the focus
● Make sure the projection screen is at least 4.6’ (1.4m) from the projector.
● Check the projection lens to see if it needs cleaning.
NOTE : Moving the projector from a cool temperature location to a warm temperature
location may result in moisture condensation on the lens. In such an event,
leave the projector OFF an d wait until condensation disappears.
Picture is Left /
Right reversed.
● Check Ceiling / Rear feature. (See “SETTING” section on page 40.)
Picture is Top /
Bottom reversed.
● Check Ceiling feature. (See “SETTING” section on page 40.)
Some displays are
not seen during the
Operation.
● Check Display feature.(See “SETTING” section on page 40.)
No image.
● Check the connection between the computer or video equipment and the projector.
● When turning the projector on, it takes about 30 seconds to display the image.
● Check that the system you selected is corresponding to the computer or the video
equipment.
● Make sure the temperature is not out of the Operating Temperature (5° ~ 35°).
No sound.
● Check audio cable connection from audio input source.
● Adjust the audio source.
● Press VOLUME (+) button.
● Press MUTE button.
APPENDIX
Problem:
Try these Solution
Remote Control
Units dose not
work.
● Check the batteries.
● Make sure nothing is blocking between the Remote Receiver and the Remote
Control Unit.
● Make sure you are not too far from the projector when using the Remote Control
Unit. Maximum operating range is 16.4 feet (5m).
Wireless Mouse
function does not
work.
● Check the cable connection between the projector and the computer.
● Check the mouse setting on your computer.
● Turn on the projector before your turn on the computer.
The image data in
memory card isn’t
displayed.
● Check the memory card is inserted properly into PC CARD SLOT.
● Check SmartMedia or PC Card Adapter is set properly.
● Check MCI mode is selected.
● Check the image data is recorded in the memory card properly.
● Start the projector again.
The image data
can’t be written in,
read from the
memory card.
● Check the projector is turned on.
● Check “Card access” in VIEW menu is selected.
● Check MCI Cable is connected properly.
● Check the memory card is inserted properly into PC CARD SLOT.
● Check Media Card Imager (supplied) is installed in your computer properly.
● Check the setting in Media Card Imager (like Serial Port Setting) is set properly.
WARNING :
High voltages are used to operate this projector. Do not attempt to open the cabinet.
Boxlight Service is easily obtained. If after following all operating instructions, you find that service is
necessary, contact Boxlight for assistance at 1-800-762-5757 or 360-779-7901.
Give the model number and explain the difficulty. We will advise you how to obtain service.
45
TECHNICAL SPECIFICATIONS
Projector Type
Dimensions (W x H x D)
Net Weight
LCD Panel System
Panel Resolution
Number of Pixels
Color System
Scanning Frequency
Projection Image size (Diagonal)
Horizontal Resolution
Projection Lens
Throw Distance
Projection Lamp
AV Input Jacks
Computer Input Jacks
Control Port Jack
MCI Serial Port
Monitor Output Jack
Computer Audio Input Jack
Audio Output Jack
Internal Audio Amp
Built-in Speaker
Feet Adjustment
Voltage
Power Consumption
Operating Temperature
Storage Temperature
Remote Control Transmitter
Accessories
Multi-media Projector
8.46" x 4.88" x 12.85" (215mm x 124mm x 326.5mm)
9.48 lbs (4.3 kg)
0.9" TFT Active Matrix type, 3 panels
1,024 x 768 dots
2,359,296 (1,024 x 768 x 3 panels)
PAL, SECAM, NTSC, NTSC4.43 and PAL-M
H-sync. 15 ~ 100 KHz, V-sync. 50 ~ 100 Hz
Adjustable from 30” to 300”
800 TV lines
F 1.7 ~ 2.0 lens with f 33.2mm ~ 43.1mm Motor zoom and focus
1.4m ~ 10.8m
120 W
RCA Type x 1 (Video, Audio R and L) and DIN 4 pin (S-Video) x 1
(VGA) HDB 15 Terminal x 1
Multi-pole 12 pin (Control Port) x 1
Serial Port DIN 8 pin
(VGA) HDB 15 Terminal x 1
Mini Jack (stereo)
Mini Jack (stereo)
1W RMS (Monaural)
1 speaker, 1.57" x 1.18" (40mm x 30mm)
0˚ to 2˚
AC 100 ~ 120 V / AC 200 ~ 240 V, 50 / 60 Hz
2.2 A / 1.1A (Max. Ampere)
41 ˚F ~ 95 ˚F (5 ˚C ~ 35 ˚C)
14 ˚F ~ 140 ˚F (-10 ˚C ~ 60 ˚C)
Power Source
Operating Range
Dimensions
Net Weight
Laser Pointer
:
:
:
:
:
AA Type x 2
16.4' (5m) / ±30˚
2.2" x 1.4" x 7.6" (56mm x 35mm x 193mm)
0.23 lbs (105 g) (including batteries)
Class II Laser (Max. Output : 1mW / Wave length : 660±20nm)
Owner’s Manual
AC Power Cord
Remote Control Transmitter and Batteries
VGA Cable
VGA / MAC Adapter
Mouse Cable (for PS/2 port x 1, for Serial port x 1, and for ADB port x 1)
MCI Cable (RS-232C)
Media Card Imager for Windows 95 (CD-ROM)
and Owner's Manual for this software
SmartMedia and PC Card Adapter
Lens Cover
Carrying Bag
● The specifications are subject to change without notice.
46
This symbol on the nameplate means the product is Listed by Underwriters Laboratories Inc. It
is designed and manufactured to meet rigid U.L. safety standards against risk of fire, casualty
and electrical hazards.
LIMITED WARRANTY
BOXLIGHT CORPORATION (“BOXLIGHT”) warrants that each Boxlight CP-15t (“the Product”) sold hereunder will
conform to and function in accordance with the written specifications of BOXLIGHT. Said limited warranty shall apply
only to the first person or entity that purchases the Product for personal or business use and not for the purpose of
distribution resale. Said warranty shall continue for a period of two (2) years from the date of such purchase.
BOXLIGHT does not warrant that the Product will meet the specific requirements of the first person or entity that
purchases the Product for personal or business use. Lamp is warrantied for 90days.
BOXLIGHT CORPORATION’s liability for the breach of the foregoing limited warranty is limited to the repair or
replacement of the Product or refund of the purchase price of the Product, at BOXLIGHT’s sole option. To exercise
the Purchaser’s rights under the foregoing warranty, the Product must be returned at the Purchaser’s sole cost and
expense, to BOXLIGHT or any authorized service center provided, however, that the Product must be accompanied by
a written letter explaining the problem and which includes (i) proof of purchase; (ii) the dealer’s name; (iii) the model
and serial number of the Product. A return authorization number, issued by the BOXLIGHT customer service
department, must also be clearly displayed on the outside of the shipping carton containing the Product.
WARRANTY LIMITATION AND EXCLUSION
BOXLIGHT CORPORATION shall have not further obligation under the foregoing limited warranty if the Product has
been damaged due to abuse, misuse, neglect, accident, unusual physical or electrical stress, unauthorized
modification, tampering, alterations, or service other than by BOXLIGHT or its authorized agents, causes other than
from ordinary use or failure to properly use the Product in the application for which said Product is intended.
DISCLAIMER OR UNSTATED WARRANTIES
The warranty printed above is the only warranty applicable to this purchase.
All other warranties express or implied, including, but not limited to, the implied warranties or merchantability and
fitness for a particular purpose are disclaimed. There are no warranties that extend beyond the face of hereof and the
foregoing warranty shall not be extended, altered or varied except by written instrument signed by BOXLIGHT
CORPORATION.
LIMITATION OR LIABILITY
It is understood and agreed that BOXLIGHT’s liability whether in contract, in tort, under any warranty, in negligence or
otherwise shall not exceed the return of the amount of the purchase price paid by purchaser and under no
circumstances shall BOXLIGHT be liable for special, indirect or consequential damages. The price stated for the
Product is a consideration in limiting BOXLIGHT’s liability. No action regardless of form, arising out of the agreement
to purchase the product, may be brought by purchaser more than one year after the cause of action has accrued.
BOXLIGHT
®
Printed in Japan
Part No. 610 278 8198 (1AA6P1P1820-- M6WE)
Boxlight
19332 Powder Hill Place
Poulsbo, WA 98370-7407 USA
www.boxlight.com
U.S. and Canada 800-762-5757
International 360-779-7901
Europe +44(0)1732-840-404
United Kingdom 0800-762-575
France 0800-9132-88
Germany 0800-180-8381