Forward Curve Inline Duct Blowers 200, 9200 and Heating/Cooling Coils Series

Forward Curve Inline Duct Blowers 200, 9200 and Heating/Cooling Coils Series
Forward Curve Inline
Duct Blowers
200, 9200 and Heating/Cooling Coils Series
705
Delhi Industries Inc. certifies that the 200, 200-2, 9200, and 9200-2 models shown herein are licensed
to bear the AMCA Seal.
The ratings shown are based on tests and procedures performed in accordance with AMCA Publications
211 & 311 and comply with the requirements of the AMCA Certified Ratings Programme.
1
200 Series
Single & Twin Inline Duct Blowers
Features
• An economical and efficient all purpose inline duct
blower for indoor use with heating, cooling and
ventilating systems
• Quiet forward curved blowers operate at low RPM
• Attractive green baked enamel paint finish
• Motor receives the cooling benefits of being in the air
stream for increased motor life
• 9/16” mounting holes are provided in the top of the
cabinet and through channels reinforcing the top panel
• Heavy duty ball bearings suitable for -650 F to +2500 F
200 Series
Indoor Applications
Insulated or Non-Insulated
• Access panels for convenient motor and drive
installation and servicing from either side
705
• All models have keywayed shafts on both ends for CW
or CCW drive
• Platform motor mounting allows models 207 to 218,
single and twin units, to be used in up-flow, down-flow
and horizontal discharge positions
• All twin units use a common shaft for balanced air
supply by each blower
• All twin unit cabinets are secured together with
angle iron rails, which extend beyond the cabinet for
suspension mounting
Side access panel removed
for illustrative purpose.
Optional Accessories
• F200A filter sections are insulated and supplied with
1” framed aluminum mesh filter. All filter tracks will
accommodate either 1” or 2” filters. Easily removed
for servicing through end access panel
• External vibration isolators
• 1/2” internal fiberglass insulation to overcome
condensation on cabinet when used in cooling
applications
• Coils - See details page 6
HC Hot Water Coil
CW Chilled Water Cooling Coil
DX Cooling Coil
2
Air Moving Products
9200 Series
Single & Twin Inline Duct Blowers
9200-VIB Series
with Internal Spring
Vibration Isolation
(Not available in twinned configuration)
Features
• All purpose heavy duty blower with weather resistant
insulated cabinet for indoor and outdoor installation
705
9200 Series
Heavy Duty, Insulated
Indoor or Outdoor Applications
• Quiet FC blowers operate at low RPM
• Attractive green corrosion resistant high solids
enamel paint finish on zinc coated outer panels
• 1/2” fiberglass insulation to reduce cabinet
condensation and energy costs
• Access panels for convenient motor and drive
installation and servicing from either side
Optional Accessories
• F200A and F9220A filter sections are insulated
and supplied with 1” framed aluminum mesh
filters. All filter sections will accommodate either
1” or 2” filters. Easily removed for servicing
through end access panel
• Factory installed vibration Isolation - Add VIB
suffix (not available in twinned configuration)
• H9209 to H9218 filtered intake hood sections
supplied with 1” aluminum mesh filters. H9220
hood section has a screened inlet for use with
F9220A filter section. (Note: Twin units require 2
filter sections or 2 hood sections)
• Heating & cooling coils- See page 6
• External vibration isolators
• Motor mounting hardware as required:
-Motor mounting platform for 9209 and 9210.
-1-5 HP base mount motor plate for 9212,9215,
9212-VIB and 9215-VIB
-1-15 HP motor platform for 9218
-Specify 1-15 HP or 20-50 HP motor platform for
model 9220
• Heavy duty ball bearings suitable for –650 F to +2500
F
• Spider bearing bracket for models 9209 to 9215
• Pillow block bearings for models 9218 and 9220
• All models have keywayed shafts both ends for CW or
CCW drive
• Reinforcing angle frame (upper illustration) is
standard on all models except 9209 and 9210
• Twin models 9212-2, 9215-2 and 9218-2 are tied
together with angle iron runners. Blowers are driven
by a common shaft for a balanced air supply by each
blower
9200 Series
shown with
Optional
Intake
Hood
• Blower is mounted on 2 steel reinforcing channels
which also contain the mounting holes for suspension
installations
3
4
- -
C
D
E
F
G
34
28
9-3/16 14-1/2 9-5/8
1-1/4
10-1/4 11-13/1617-1/2 11-3/4 1-1/4
8-1/4
M
R
S
T
D
E
24
H
2-3/4
19-1/2 2-5/8
K
1-3/4
1-3/4
30-1/2
18
25
21
L
M
1-1/8 35-3/8 31-5/8
7/8
25
20-1/4
16
R
- -
- -
3
2
2
2
158
140
82
65
55
43
--
287
191
152
142
112
A
21
22-1/4
30-1/8
33-3/4
41-1/2
44-3/4
MODEL
9209 & 9209-2
9210 & 9210-2
9212 & 9212-2
9215 & 9215-2
9218 & 9218-2
9220 & 9220-2
89-1/2
83-3/8
67-5/8
60-1/8
44-1/2
42
41-1/8
34
28-5/8
24-3/4
20
18
57-1/2
44
38-1/8
34
24-3/4
23
25-3/4
19-5/8
17
14-1/2
12-3/8
11-1/4
25-3/4
22-5/8
19-5/8
16-5/8
14-1/8
12-3/4
3
2-3/4
2-1/8
2-1/8
1
1
1-1/8
1-1/8
1-1/8
1-1/8
1-1/8
1-1/8
38-3/8
35-3/8
30-5/8
25-1/8
20-1/4
19
35-1/8
31-5/8
25-1/4
21-1/8
18
16
19
19
14-1/8
13-1/4
9-1/8
9-1/4
6-1/8
6-1/4
2-7/8
4-3/4
2
2
T
9212-2, 9215-2 & 9218-2 only.
2 X 2 X 3/16” twinning support rails
on 9220-2 only
1-1/8” bolted flange
- -
14-7/8 69-1/4
11-3/8 56-1/4
9-1/8 46-3/4
9-3/16 44-1/4
2
515
323
176
143
70
61
1048
666
403
334
165
140
Twin
Single
C
35
28
7/8
7/8
19
15-7/8 13-3/8 8-13/16 38-1/4
L
B
19-5/8 22-5/8
15-7/8 18-5/8
1-3/4
1-3/4
7/8
7/8
K
Unit Wt. (lbs.)
44
32
27-1/2 13-7/16 15-5/8 23-1/2 16-1/8 1-1/4
1-3/4
1-1/4
J
Dimensions
A2
23
23
H
24-3/4 11-3/8 13-1/8 18-3/4 13-3/8 1-1/4
Note: Dimensions also applicable
to 9200-VIB series with
internal vibration isolation
(not available in twinned
configuration)
41-1/2
218 67
54
215 & 215-2 33-1/2
27
20
18
23
42
15-3/8
212 & 212-2
21
209 & 209-2
36
B
210 & 210-2 22-1/4 44-1/2
18
207 & 207-2
A2
Single Twin
A
MODEL
Unit Wt. (lbs.)
holes on “G & S” dimension centers.
top and bottom with 5/8” mounting
Dimensions
200, 200-2, 9200 &
9200-2 Dimensions
Structural steel angle twinning rail,
Air Moving Products
Filter Sections & Intake Hoods
Series F200A & F9220A
F200A
Filter Section
For 200 & 9200 Series
Duct Blowers
Series H9200
F9220A
Filter Section
For Model 9220
Duct Blower
H9200
Intake Hood
For 9200 Series
Duct Blowers
Dimensions (inches)
Filter Unit
Unit
Model A B N P Size (Qty) Wt.
M
odel L M Z Filter Size (Qty) Wt.
(Lbs.)
(Lbs.)
F207A 17-3/4 15-3/8 13-1/2 14-1/8 x 16-5/8 (1) 11 18 19-1/8 16-1/8 16-3/4 x 19-7/8 (1) 12 H9209 19-1/4 16-9/16 21-1/4 F210A 22-1/4 20 20-3/8 18-1/8 18-3/4 x 21-1/8 (1) 14 H9210 20-1/2 18-9/16 25-3/4 15 x 20 (2) 16
F212A 23 25-1/8 21-1/8 21-3/4 x 25-7/8 (1) 16 H9212 25-3/8 21-9/16 30-3/4 20 x 25 & 16 x 25 (2) 27
F209A 21 27 16 F215A 32-1/2 26-3/4 30-5/8 25-1/8 F218A 37 33-1/4 35-1/4 31-1/2 F9220A 39-3/4 37-1/4 38-1/2 35-1/4 25-3/4 x 31 N/A F207A
F209A
F210A
--
--
--
16 x 24 (1) 21 H9215 31-3/16 25-13/16 33-1/2 20 x 28-1/2 32-1/4 x 35-7/8 (1) 46 H9218 35-5/8 32-11/16 40-1/4 20 x 25 (2) & 16 x 25 64 H9220 38-5/8 20 x 25 (6) Filter Section
CFM
--
F212A
35-9/16 22 --
--
(1) 14
(2) (2)
Filters not included - Use F9220A
38
50
40 Hood Section
F215A
F218A F9220A H9209 H9210 H9212 H9215 H9218
300
.010
.007
.013
400
.018
.010
.018
600
.030
.020
.013
.030
.018
800
.067
.026
.022
.012
.043
.025
.015
1000
.117
.042
.028
.020
.065
.034
.019
1200
.171
.073
.041
.023
.012
.093
.043
.023
.017
1300
.091
.053
.025
.015
.107
.049
.027
.019
1400
.109
.067
.029
.018
.122
.055
.030
.020
1600
.145
.095
.038
.021
.011
.072
.035
.025
1800
.182
.124
.054
.024
.013
.091
.042
.030
2000
.154
.073
.026
.017
.109
.048
.034
2500
.126
.042
.023
.073
.045
3000
.182
.073
.028
.103
.061
3500
.110
.040
.131
.082
4000
.147
.057
.023
.107
4500
.182
.082
.027
.130
5000
.107
.032
5500
.132
.036
6000
.157
.040
6500
.182
.046
7000
.052
7500
.058
8000
.065
8500
.074
9000
.082
10000
.101
11000
.118
12000
.137
Maximum CFM
1250
1800
2200
3500
4500
6700
12000
1450
2200
3500
4500
5
.015
.017
.019
.025
.032
.040
.048
.059
.072
.088
.103
.117
.131
7000
6
HC-07 & CW-07 & DX-18-07
HC-09 & CW-09 & DX-24-09
P
A
N
6”
HC Coils
1”
33-1/2
26-3/4
23 20
18
15-3/8
13-1/2
30-5/8 25-1/8
25-1/8 21-1/8
20-3/8 18-1/8
19-1/8 16-1/8
16
3/4
3/4
5/8
5/8
5/8
3/4 3/4
5/8
5/8
5/8
P
A
N
1”
6”
0 5/8”
CW Coils
DX Coils
Note:
DX coil is supplied with low pressure drop venturi type distributor for use with
customer supplied expansion device.
B
DX Series
Direct Expansion Coils
With Built-in Condensate Pan
3 - Hot Water Heating Coil
1 - 210 Duct Blower,
2 - DX30/36-10 Cooling Coil,
3 - HC-10 Hot Water Coil
4 - F210 Filter Section
Example:
1 - 200 Series Duct Blower
2 - DX Coil
4 - Filter Section
32
23
17
14
10
• All coils are sized to mount to the inlet of the corresponding
sized duct blower or coil and filter section as illustrated
in the modular set up illustrated.
Features
For complete details and capacities on HC, CW & DX Coils request catalogue SS-38.
32-1/2
27
HC-15 & CW-15 & DX-60-15
HC-12 & CW-12 & DX-42/48-12
21
22-1/4
HC-CW - DX Coils
B
CW Series
Chilled Water Cooling Coils
With Built-in Condensate Pan
7/8 7/8
7/8
7/8
5/8
7/8 7/8 7/8
7/8
5/8
5/8
1/2
1/2
1/2
1/2
Drain is 5/8 in-OD
61
42
36
29
22
7/8
7/8
5/8
5/8
5/8
61
42
36
29
22
A
B
N
P
INLET OUTLET UNIT WT. INLET OUTLET UNIT WT. INLET OUTLET UNIT WT.
(CW & DX)
(LBS.)
(LBS.)
(LBS.) 17-3/4
A
(HC)
1”
2-1/4”
HC-10 & CW-10 & DX-30/36-10
MODEL
N
Dimensions (in)
A
P
B
HC Series
Hot Water Heating Coils
Heating & Cooling Coils
‘HC’, ‘CW’ & ‘DX’ Series
Air Moving Products
207
CFM
Max. 3/4 HP,
3/4” Shaft OUTLET
VELOCITY
FPM
300
400
500
600
700
800
900
1000
1100
1200
1300
569
759
949
1139
1329
1519
1709
1899
2089
2279
2469
1400
2659
207-2
CFM
FPM
526
567
636
719
806
894
983
1073
1165
1257
1351
0.01
0.02
0.04
0.06
0.08
0.12
0.16
0.21
0.27
0.35
0.43
1.3
1.8
3.1
4.3
6.4
8.6
10.8
12.6
14.1
15.8
17.9
1445 0.53 22
1/8” SP 2800
2659
1445 1.07 26
SP x 0.249 = kPa
SI CONVERSION FACTOR
600
700
800
900
1000
1100
1200
1300
1400
1500
1600
1700
OUTLET
VELOCITY
FPM
- -
3.9
4.2
6.2
8.7
10.1
12.1
13.3
14.8
16.5
18.5
1505 0.59
22
0.03
0.05
0.07
0.11
0.17
0.24
0.32
0.43
0.55
0.70
0.87
1.9
2.5
3.9
5.3
7.9
10.6
13.0
15.1
16.8
18.9
21
3.8
4.9
5.3
7.6
10.5
12.1
14.5
16.0
17.7
19.7
22
1505 1.17
27
1200
1400
1600
1800
2000
2200
2400
2600
2800
3000
3200
3400
FPM
713
832
951
1070
1189
1308
1427
1546
1665
1783
1902
2021
- -
- -
9.3
10.1
10.8
11.7
12.9
14.7
15.6
17.6
21
1247
1257
1246
1255
1278
1308
1350
1400
1465
1539
1618
0.09
0.11
0.13
0.16
0.20
0.24
0.29
0.35
0.43
0.52
0.62
2” SP - -
- -
- -
11.8
12.5
12.9
13.8
15.1
17.7
23
37
1433
1448
1450
1437
1451
1473
1503
1540
1588
1644
1713
0.12
0.15
0.18
0.20
0.24
0.30
0.36
0.43
0.50
0.58
0.69
- -
- -
- -
- -
14.3
15.7
20.7
17.6
19.8
23
27
1733
1761
1775
1777
1763
1768
1785
1809
1840
- -
- -
0.19
0.24
0.28
0.32
0.35
0.41
0.48
0.57
0.66
- -
- -
- -
- -
- -
- -
22
23
24
26
29
- -
- -
1980
2020
2038
2051
2052
2038
2038
2053
- -
- -
- -
0.26
0.33
0.39
0.45
0.50
0.54
0.61
0.70
- -
- -
- -
26
- -
- -
- -
- -
- -
- -
- -
- -
24 1701 0.74
145T Frame
Wheel Dia, 7.75” 3/4” SP 1” SP 2-1/2” SP
-
-
-
-
-
-
-
-
-
-
-
-
- -
2189
2242
2271
2286
2295
2292
- -
- -
- -
- -
- -
0.33
0.42
0.50
0.58
0.65
0.71
- -
- -
- -
- -
- -
- -
- -
-
-
- -
Tip Speed: 2.03 X RPM = FPM
1-1/2” SP 1026
1019
1027
1051
1086
1134
1198
1272
1352
1438
1526
0.11
0.14
0.18
0.23
0.30
0.37
0.47
0.59
0.74
0.91
1.12
1613 1.35
11.1
10.8
11.2
12.1
12.9
14.0
15.5
17.6
18.7
21
25
1247
1257
1246
1255
1278
1308
1350
1400
1465
1539
1618
0.18
0.22
0.25
0.31
0.39
0.49
0.59
0.70
0.85
1.03
1.24
- -
14.1
13.7
14.0
15.0
15.4
16.5
18.1
21
28
- -
2” SP 29 1701 1.49 - -
1433
1448
1450
1437
1451
1473
1503
1540
1588
1644
1713
0.24
0.30
0.36
0.40
0.49
0.60
0.72
0.85
1.00
1.17
1.38
- -
16.8
17.0
16.3
17.1
18.8
25
21
24
28
33
1733
1761
1775
1777
1763
1768
1785
1809
1840
- -
- -
0.38
0.48
0.57
0.64
0.71
0.82
0.97
1.13
1.32
- -
- -
- -
27
28
28
27
28
29
32
35
- -
- -
1980
2020
2038
2051
2052
2038
2038
2053
- -
- -
- -
0.51
0.65
0.79
0.90
1.00
1.08
1.22
1.40
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
209 -Max. 3/4 HP, 145T Frame
9209 -Max. 1-1/2 HP, 145T Frame
3/4” Shaft Wheel Dia, 10.13” 1/8” SP 417
440
468
499
534
573
613
654
696
739
782
826
OUTLET
VELOCITY
1-1/2” SP 2-1/2” SP
1/4” SP 1/2” SP 3/4” SP 1” SP -
-
-
-
-
-
-
-
-
-
-
-
- -
2189
2242
2271
2286
2295
2292
- -
- -
- -
- -
- -
0.67
0.83
1.00
1.16
1.29
1.42
- -
- -
- -
- -
- -
- -
- -
-
-
- -
Tip Speed: 2.65 X RPM = FPM
1-1/2” SP 2” SP 2-1/2” SP
RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP S
ONES
713
832
951
1070
1189
1308
1427
1546
1665
1783
1902
2021
0.06
0.07
0.09
0.12
0.15
0.18
0.23
0.29
0.37
0.46
0.56
1/2” SP 719 0.05
737 0.07
770 0.11
822 0.15
894 0.20
975 0.28
1062 0.37
1149 0.49
1236 0.63
1325 0.79
1414 0.97
0.03
0.04
0.06
0.07
0.09
0.12
0.15
0.19
0.23
0.28
0.34
0.40
1.6
1.3
1.8
2.2
2.7
3.4
4.5
6.1
7.0
7.7
8.3
8.8
557
566
581
601
625
653
682
714
750
788
828
868
0.05
0.06
0.07
0.10
0.12
0.15
0.18
0.22
0.26
0.31
0.37
0.43
1/8” SP 2.2
2.5
3.8
3.1
4.1
6.9
10.3
5.2
5.9
6.7
7.5
8.3
798
791
786
792
802
816
834
856
881
907
936
966
0.10
0.11
0.12
0.14
0.17
0.20
0.24
0.28
0.33
0.38
0.44
0.51
5.7
5.4
5.2
5.5
5.8
6.7
8.0
7.0
7.6
8.2
8.9
9.6
977
979
974
964
964
970
979
992
1009
1028
1050
1075
Max. 1-1/2 HP,
3/4” Shaft 1/4” SP 1/2” SP 209-2
& 9209-2
CFM
1026
1019
1027
1051
1086
1134
1198
1272
1352
1438
1526
1613 0.67
1/4” SP 526
567
636
719
806
894
983
1073
1165
1257
1351
1” SP RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP S
ONES
569
759
949
1139
1329
1519
1709
1899
2089
2279
2469
3/4” SP Max. 1-1/2 HP,
3/4” Shaft 600
800
1000
1200
1400
1600
1800
2000
2200
2400
2600
CFM
1/2” SP 719 0.03
737 0.04
770 0.05
822 0.07
894 0.10
975 0.14
1062 0.19
1149 0.24
1236 0.31
1325 0.39
1414 0.48
209
& 9209
CFM x 0.472 = L/s
1/4” SP Tip Speed: 2.03 X RPM = FPM
RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP S
ONES
OUTLET
VELOCITY
1/8” SP 145T Frame
Wheel Dia, 7.75” 0.15
0.17
0.19
0.21
0.23
0.27
0.30
0.35
0.40
0.46
0.52
0.59
8.5
8.6
8.4
8.1
8.1
8.3
8.6
8.9
9.4
10.1
10.4
11.1
1120
1128
1130
1126
1118
1112
1115
1122
1132
1145
1162
1181
0.21
0.23
0.26
0.28
0.31
0.34
0.38
0.42
0.48
0.53
0.60
0.68
10.8
11.1
11.2
11.0
10.7
10.5
10.6
10.9
11.3
11.9
13.6
17.5
145T Frame
Wheel Dia, 10.13” 3/4” SP 1” SP 1353
1367
1379
1384
1384
1379
1371
1362
1362
1367
1375
1385
0.33
0.37
0.41
0.45
0.48
0.52
0.56
0.60
0.65
0.71
0.78
0.86
- -
- -
15.8
16.2
16.2
15.8
15.3
14.8
14.8
15.1
15.6
16.2
1548
1564
1578
1590
1596
1598
1596
1590
1582
1573
1573
1576
0.45
0.50
0.56
0.61
0.67
0.72
0.76
0.81
0.87
0.92
0.99
1.07
- - 1717
- - 1736
- - 1751
19.7 1764
20 1777
20 1784
20 1787
19.7 1786
19.3 1781
18.8 1775
18.8 1765
19.0 1758
0.59
0.65
0.72
0.79
0.85
0.92
0.98
1.04
1.10
1.17
1.23
1.31
- - - - 24
24
24
24
24
24
23
23
Tip Speed: 2.65 X RPM = FPM
1-1/2” SP 2” SP 2-1/2” SP
RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP S
ONES
417
440
468
499
534
573
613
654
696
739
782
826
0.06
0.08
0.11
0.14
0.19
0.24
0.30
0.38
0.46
0.56
0.67
0.80
- -
- -
3.3
4.1
5.0
6.0
7.2
8.6
10.1
11.8
13.6
15.3
557
566
581
601
625
653
682
714
750
788
828
868
0.09
0.12
0.15
0.19
0.24
0.29
0.36
0.43
0.52
0.62
0.73
0.86
4.4
4.6
4.9
5.4
6.2
7.1
8.1
9.2
10.7
12.2
13.8
15.4
798
791
786
792
802
816
834
856
881
907
936
966
0.19
0.22
0.25
0.29
0.34
0.40
0.48
0.56
0.66
0.77
0.88
1.02
10.6
10.3
10.1
10.3
10.8
11.3
11.9
12.7
13.6
14.6
15.7
16.8
977
979
974
964
964
970
979
992
1009
1028
1050
1075
0.30
0.34
0.37
0.41
0.47
0.53
0.61
0.69
0.80
0.92
1.05
1.19
15.9
15.9
15.8
15.5
15.5
15.7
16.0
16.4
16.9
17.4
18.1
19.0
1120
1128
1130
1126
1118
1112
1115
1122
1132
1145
1162
1181
0.41
0.47
0.52
0.56
0.62
0.68
0.76
0.85
0.95
1.06
1.20
1.36
19.4
19.7
19.7
19.5
19.2
19.0
19.1
19.4
19.8
20
21
22
1353
1367
1379
1384
1384
1379
1371
1362
1362
1367
- -
- -
0.65
0.73
0.81
0.89
0.97
1.03
1.11
1.20
1.31
1.43
- -
- -
25
26
27
27
27
27
26
26
26
26
- -
- -
1548
1564
1578
1590
1596
1598
- -
- -
- -
- -
- -
- -
0.90
1.01
1.12
1.23
1.33
1.44
- -
- -
- -
- -
- -
- -
33 1717 1.17 43
34 1736 1.30 44
35 1751 1.43 45
36 - -
- - - 37 - -
- - - 37 - -
- - - - - - -
- - - - - - -
- - - - - - -
- - - - - - -
- - - - - - -
- - - - - - -
- - - -
Performance certified is for installation Type B - Free inlet, Ducted outlet. Power rating bhp does not include transmission losses.
Performance ratings do not include the effects of appurtenances (accessories). The sound ratings shown are loudness values in fan sones at 5 ft. (1.5m)
in a hemispherical free field calculated per AMCA Standard 301. Values shown are for Installation Type B: free inlet hemispherical fan sone levels.
Sone values not documented in unlisted areas. Twin unit data is derived from tests of single width fans.
7
210
& 9210
CFM
800
900
1000
1100
1200
1300
1400
1500
1600
1700
1800
1900
OUTLET
VELOCITY
FPM
1/8” SP Max. 1/2 HP,
3/4” Shaft 1/4” SP 771
868
964
1060
1157
1253
1350
1446
1543
1639
1736
1832
388
403
422
445
470
497
525
553
582
612
642
672
1600
1800
2000
2200
2400
2600
2800
3000
3200
3400
3600
3800
OUTLET
VELOCITY
FPM
1/2” SP 3/4” SP 1” SP Tip Speed: 2.99 X RPM = FPM
1-1/2” SP 2” SP 2-1/2” SP
RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP S
ONES
0.04
0.05
0.06
0.08
0.10
0.12
0.15
0.18
0.22
0.25
0.29
0.34
2.0
2.5
2.4
3.0
3.8
5.4
4.9
5.6
6.7
7.8
8.8
9.7
511
520
531
544
559
575
593
616
640
666
693
720
0.07
0.08
0.09
0.11
0.13
0.15
0.18
0.21
0.25
0.29
0.33
0.38
1/8” SP 3.1
3.7
4.6
6.0
8.7
4.6
5.3
6.5
8.0
9.6
11.0
12.1
709
712
713
719
728
738
749
762
776
791
807
824
0.12 5.9 861
0.14 6.0 866
0.15 6.1 869
0.18 6.3 872
0.20 6.8 873
0.23 7.2 878
0.26 7.8 886
0.29 8.4 895
0.33 9.0 905
0.37 9.6 916
0.41 10.2 928
0.46 10.4 942
Max. 1-1/2 HP,
3/4” Shaft 1/4” SP 1/2” SP 210-2
& 9210-2
CFM
145T Frame
Wheel Dia, 11.44” 0.18
0.21
0.23
0.26
0.28
0.31
0.34
0.38
0.42
0.46
0.51
0.56
8.8
9.0
9.1
9.2
9.3
9.5
9.9
10.3
10.8
11.3
11.9
12.6
987
993
998
1002
1005
1007
1009
1013
1021
1030
1040
1051
0.25
0.27
0.31
0.34
0.37
0.40
0.43
0.47
0.52
0.57
0.62
0.68
- -
11.8
12.0
12.2
12.4
12.5
12.6
12.8
13.2
13.7
14.3
14.9
145T Frame
Wheel Dia, 11.44” 3/4” SP 1” SP 1196
1204
1210
1216
1221
1225
1229
1232
1234
1235
1239
1246
0.41
0.44
0.47
0.50
0.55
0.61
0.65
0.70
0.74
0.79
0.84
0.91
- -
- -
- -
16.7
17.0
17.2
17.4
17.6
17.7
17.8
18.0
18.4
1371
1380
1387
1394
1400
1405
1410
1415
1419
1422
1424
1426
0.58
0.62
0.66
0.70
0.74
0.79
0.86
0.93
1.00
1.06
1.12
1.17
- -
- -
- -
- -
21
21
21
22
22
22
22
22
1524
1533
1542
1550
1557
1563
1568
1573
1578
1583
1587
1590
0.76
0.81
0.87
0.92
0.97
1.02
1.07
1.14
1.23
1.32
1.40
1.48
- - - - - - 25
26
26
27
27
27
Tip Speed: 2.99 X RPM = FPM
1-1/2” SP 2” SP 2-1/2” SP
RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP S
ONES
771
868
964
1060
1157
1253
1350
1446
1543
1639
1736
1832
388
403
422
445
470
497
525
553
582
612
642
672
0.08
0.10
0.13
0.16
0.20
0.25
0.30
0.36
0.43
0.51
0.59
0.68
2.7
3.2
3.1
3.7
4.7
6.6
6.0
6.8
8.0
9.3
10.6
11.7
511
520
531
544
559
575
593
616
640
666
693
720
0.13
0.16
0.18
0.22
0.26
0.30
0.35
0.42
0.49
0.57
0.66
0.77
3.9
4.6
5.6
7.3
10.6
5.7
6.5
7.9
9.7
11.5
13.3
14.5
709
712
713
719
728
738
749
762
776
791
807
824
0.25
0.28
0.31
0.35
0.40
0.45
0.51
0.58
0.65
0.73
0.82
0.91
7.2
7.3
7.4
7.7
8.2
8.8
9.4
10.1
10.9
11.6
12.4
12.7
861
866
869
872
873
878
886
895
905
916
928
942
0.36
0.42
0.47
0.51
0.55
0.61
0.69
0.76
0.84
0.93
1.02
1.13
10.7
11.0
11.1
11.3
11.4
11.7
12.1
12.6
13.1
13.7
14.4
15.2
987
993
998
1002
1005
1007
1009
1013
1021
1030
1040
1051
0.51
0.55
0.61
0.69
0.75
0.80
0.86
0.95
1.04
1.14
1.25
1.35
- -
14.3
14.5
14.8
15.0
15.1
15.2
15.4
15.8
16.4
17.0
17.8
1196
1204
1210
1216
1221
1225
1229
1232
1234
- -
- -
- -
0.82
0.88
0.94
1.00
1.10
1.21
1.31
1.40
1.48
- -
- -
- -
- -
- -
- -
20
20
21
21
21
21
- -
- -
- -
1371
1380
1387
1394
1400
- -
- -
- -
- -
- -
- -
- -
1.16
1.24
1.32
1.40
1.49
- -
- -
- -
- -
- -
- -
- -
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
212 - Max. 1-1/2HP, 145T Frame 3/4” Shaft
9212 - Max. 3 HP, 145T Frame 1” Shaft
Wheel Dia, 12.50” Tip Speed: 3.27 X RPM = FPM
212 & 9212
CFM
1200
1400
1600
1800
2000
2200
2400
2600
2800
3000
3200
3400
OUTLET
VELOCITY
FPM
823
960
1097
1234
1371
1508
1646
1783
1920
2057
2194
2331
1/8” SP 1/4” SP 1/2” SP 3/4” SP 1” SP 1-1/2” SP 2” SP 2-1/2” SP
RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP S
ONES
386
415
445
477
511
546
582
620
658
697
737
777
0.07
0.09
0.13
0.17
0.22
0.28
0.34
0.43
0.52
0.63
0.75
0.89
2.0
2.8
4.1
6.2
5.1
6.0
7.3
8.4
9.3
10.3
11.5
12.9
486
507
533
560
589
620
651
684
718
753
788
825
0.10
0.14
0.17
0.22
0.27
0.34
0.41
0.50
0.60
0.71
0.84
0.98
3.4
4.0
5.0
6.4
7.7
9.0
10.0
10.7
9.8
11.0
12.3
13.4
649
661
679
698
720
745
772
801
830
859
890
922
0.18
0.22
0.27
0.33
0.39
0.47
0.55
0.65
0.76
0.88
1.02
1.18
- -
- -
10.8
9.3
9.9
10.6
11.4
12.3
13.1
14.0
15.0
16.0
816
797
801
817
836
855
877
901
927
954
983
1012
0.31
0.33
0.37
0.44
0.51
0.60
0.69
0.80
0.92
1.05
1.20
1.37
- - 945 0.42
- - 941 0.47
- - 921 0.50
10.5 922 0.55
10.4 937 0.64
11.0 955 0.73
11.7 973 0.84
12.6 993 0.95
13.5 1015 1.08
14.6 1040 1.23
16.1 1066 1.39
18.410933 1.56
- -
- -
- -
- -
- -
13.5
14.0
14.6
15.2
16.0
17.1
19.1
1141
1155
1161
1144
1125
1129
1143
1161
1179
1198
1219
1240
0.64
0.75
0.84
0.89
0.93
1.02
1.13
1.27
1.42
1.59
1.77
1.96
- -
- -
- -
- -
- -
- -
- -
- -
18.3
18.9
19.6
20
1300
1319
1333
1340
1329
1309
1298
1307
1322
1341
1359
1377
0.87
1.00
1.14
1.26
1.34
1.39
1.47
1.61
1.77
1.96
2.16
2.37
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
23
24
1439
1460
1478
1491
1498
1490
1469
1452
1456
1468
1485
1504
1.11
1.26
1.43
1.60
1.76
1.87
1.93
2.00
2.15
2.34
2.55
2.79
-
-
212 - 2 - Max. 1-1/2HP, 145T Frame 3/4” Shaft
9212 - 2 - Max. 3 HP, 145T Frame 1” Shaft
Wheel Dia, 12.50” Tip Speed: 3.27 X RPM = FPM
212-2 & 9212-2
CFM
2400
2800
3200
3600
4000
4400
4800
5200
5600
6000
6400
6800
OUTLET
VELOCITY
FPM
823
960
1097
1234
1371
1508
1646
1783
1920
2057
2194
2331
1/8” SP 1/4” SP 1/2” SP 3/4” SP 1” SP 1-1/2” SP 2” SP 2-1/2” SP
RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP S
ONES
386
415
445
477
511
546
582
620
658
697
737
777
0.14
0.19
0.26
0.34
0.43
0.55
0.69
0.85
1.04
1.25
1.50
1.78
2.7
3.5
5.0
7.5
6.2
7.3
8.7
10.1
11.3
12.6
14.0
15.6
486
507
533
560
589
620
651
684
718
753
788
825
0.21
0.27
0.35
0.44
0.55
0.68
0.83
1.00
1.20
1.42
1.67
1.96
4.2
5.0
6.2
7.8
9.4
10.7
12.0
12.9
12.0
13.4
14.8
16.1
649
661
679
698
720
745
772
801
830
859
890
922
0.37
0.44
0.54
0.65
0.78
0.93
1.10
1.30
1.52
1.77
2.04
2.35
- -
- -
8.0
8.7
9.5
10.4
11.5
12.6
13.9
15.3
17.0
19.9
816
797
801
817
836
855
877
901
927
954
983
1012
0.61
0.65
0.74
0.87
1.02
1.19
1.38
1.60
1.84
2.11
2.41
2.74
- -
- -
- -
12.7
12.6
13.4
14.2
15.2
16.2
17.4
19.2
22
945
941
921
922
937
955
973
993
1015
1040
1066
- -
0.85
0.95
1.00
1.11
1.27
1.46
1.67
1.91
2.17
2.46
2.78
- -
- -
- -
- -
- -
- -
16.1
16.7
17.4
18.2
19.2
20
- -
1141
1155
1161
1144
1125
1129
1143
1161
1179
- -
- -
- -
1.29
1.49
1.68
1.77
1.85
2.03
2.27
2.55
2.85
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
22
- -
- -
- -
1300
1319
1333
1340
1329
1309
1298
- -
- -
- -
- -
- -
1.73
2.00
2.27
2.53
2.69
2.79
2.94
- -
- -
- -
- -
- -
-
- 1439 2.22 - - 1460 2.52 - - 1478 2.86 - - - - - - - - - -
- - - - - -
- - - - - -
- - - - - -
- - - - - -
- - - - - -
- - - - - -
- - - - - -
- - - -
Performance certified is for installation Type B - Free inlet, Ducted outlet. Power rating bhp does not include transmission losses.
Performance ratings do not include the effects of appurtenances (accessories). The sound ratings shown are loudness values in fan sones at 5 ft. (1.5m)
in a hemispherical free field calculated per AMCA Standard 301. Values shown are for Installation
8 Type B: free inlet hemispherical fan sone levels.
Sone values not documented in unlisted areas. Twin unit data is derived from tests of single width fans.
Air Moving Products
215 - Max. 3 HP, 184T Frame 1” Shaft
9215 - Max. 5 HP, 184T Frame 1” Shaft
Wheel Dia, 15.25” Tip Speed: 3.99 X RPM = FPM
215 & 9215
CFM
1800
1900
2000
2100
2200
2300
2400
2500
2600
2700
2800
2900
3000
3100
3200
3300
3400
3500
3600
3700
3800
3900
4000
4100
4200
4300
4400
OUTLET
VELOCITY
FPM
1/8” SP 1/4” SP 1/2” SP 3/4” SP 1” SP 1-1/2” SP 2” SP 2-1/2” SP
RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP S
ONES
876
925
974
1022
1071
1120
1168
1217
1266
1314
1363
1412
1461
1509
1558
1607
1655
1704
1753
1801
1850
1899
1948
1996
2045
2094
2142
273
278
284
290
297
305
314
323
332
342
352
363
373
384
394
405
416
427
437
448
459
470
481
492
503
514
526
0.10
0.11
0.12
0.14
0.15
0.17
0.19
0.21
0.23
0.26
0.29
0.31
0.35
0.38
0.42
0.45
0.49
0.54
0.58
0.63
0.68
0.73
0.79
0.85
0.91
0.97
1.04
2.7
3.4
4.2
2.9
3.5
4.2
4.8
5.5
4.6
5.1
5.6
6.0
6.4
6.7
7.0
7.2
7.4
7.8
8.3
8.8
9.4
9.9
10.5
11.1
11.7
12.4
12.9
370
373
375
375
376
378
381
385
389
394
400
406
413
420
427
436
445
454
463
473
483
493
503
513
523
534
544
0.18
0.19
0.20
0.21
0.22
0.23
0.25
0.27
0.29
0.32
0.34
0.37
0.40
0.43
0.46
0.50
0.54
0.58
0.62
0.67
0.72
0.78
0.83
0.89
0.95
1.02
1.09
4.8
5.0
4.5
4.6
4.6
4.7
4.8
5.1
5.3
5.6
5.9
6.2
6.5
7.1
8.8
10.3
12.0
14.1
16.4
9.4
10.0
10.8
11.9
13.1
14.2
15.4
16.6
510
510
510
510
511
514
517
521
525
528
530
531
531
532
533
536
539
543
547
552
557
562
568
574
581
588
595
0.29
0.32
0.35
0.38
0.41
0.44
0.46
0.49
0.51
0.54
0.56
0.58
0.60
0.62
0.65
0.68
0.71
0.75
0.80
0.84
0.89
0.94
0.99
1.04
1.10
1.16
1.22
8.8
9.0
9.0
9.0
9.2
10.0
10.8
12.0
13.3
14.3
9.0
9.1
9.2
9.2
9.3
9.5
9.7
10.0
10.7
11.6
12.5
13.6
14.9
16.1
12.5
13.1
13.8
617
620
622
623
624
624
624
624
625
626
629
632
636
640
643
646
649
650
651
651
652
653
655
658
661
665
670
0.42
0.44
0.47
0.50
0.54
0.58
0.62
0.67
0.71
0.76
0.80
0.84
0.87
0.91
0.95
0.98
1.01
1.04
1.08
1.10
1.14
1.18
1.23
1.28
1.33
1.39
1.46
11.3
11.5
11.7
11.8
11.9
11.9
12.0
12.0
12.1
12.2
12.6
13.0
13.8
14.5
15.0
15.6
13.6
13.7
13.8
13.8
13.9
13.9
14.1
14.3
14.5
14.9
15.8
705
708
711
714
716
718
720
721
721
721
721
721
722
723
725
728
732
736
740
743
746
749
750
751
751
752
753
0.57
0.60
0.62
0.65
0.68
0.72
0.76
0.81
0.86
0.92
0.98
1.04
1.09
1.15
1.21
1.26
1.31
1.36
1.41
1.46
1.51
1.55
1.59
1.63
1.67
1.71
1.76
14.1
14.3
14.6
14.9
15.1
15.3
15.5
15.5
15.5
15.5
15.5
15.5
15.6
15.8
15.9
16.2
16.6
16.9
17.3
17.5
17.8
17.6
17.7
17.8
17.8
17.8
17.9
850
854
857
860
863
866
869
872
875
877
879
881
882
883
883
883
883
883
883
884
886
888
891
894
898
902
906
0.88
0.93
0.97
1.01
1.05
1.09
1.13
1.17
1.21
1.26
1.31
1.37
1.44
1.51
1.59
1.68
1.77
1.86
1.94
2.03
2.12
2.20
2.29
2.36
2.44
2.52
2.59
18.3
18.6
19.0
19.3
19.7
20
20
21
21
22
22
23
23
23
23
23
23
23
23
24
25
26
27
29
32
35
39
969
974
978
982
986
989
992
995
999
1002
1005
1007
1010
1012
1015
1016
1018
1019
1019
1020
1020
1020
1020
1020
1020
1022
1023
1.20
1.26
1.32
1.37
1.43
1.48
1.54
1.59
1.64
1.69
1.75
1.81
1.87
1.93
2.00
2.07
2.16
2.25
2.35
2.46
2.57
2.69
2.81
2.93
3.05
3.16
3.28
21
22
22
22
23
23
24
24
25
25
25
26
26
27
27
27
28
28
28
28
28
28
28
28
28
29
29
1071
1077
1083
1088
1092
1096
1100
1104
1107
1110
1113
1116
1119
1122
1125
1128
1130
1133
1135
1137
1138
1139
1140
1140
1140
1140
1140
1.52
1.59
1.67
1.74
1.81
1.89
1.96
2.02
2.09
2.16
2.22
2.29
2.36
2.42
2.49
2.57
2.64
2.73
2.81
2.91
3.01
3.13
3.25
3.38
3.52
3.67
3.81
24
25
25
26
27
27
27
28
29
29
29
29
30
30
31
32
32
32
32
33
33
33
33
33
33
33
33
215 -2 - Max. 3 HP, 184T Frame 1” Shaft
9215 -2 - Max. 5 HP, 184T Frame 1” Shaft
Wheel Dia, 15.25” Tip Speed: 3.99 X RPM = FPM
215-2 & 9215-2
CFM
SP x 0.249 = kPa
CFM x 0.472 = L/s
SI CONVERSION FACTOR
OUTLET
VELOCITY
FPM
1/8” SP 1/4” SP 1/2” SP 3/4” SP 1” SP 1-1/2” SP 2” SP 2-1/2” SP
RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP S
ONES
3600
3800
4000
4200
4400
4600
876
925
974
1022
1071
1120
273
278
284
290
297
305
0.20
0.22
0.25
0.28
0.31
0.34
3.5
4.2
5.0
3.8
4.5
5.2
370
373
375
375
376
378
0.35
0.38
0.40
0.42
0.44
0.47
5.8
6.0
5.6
5.7
5.7
5.8
510
510
510
510
511
514
0.59
0.64
0.70
0.76
0.82
0.87
10.2
10.5
10.5
10.5
10.8
11.5
617
620
622
623
624
624
0.84
0.89
0.94
1.00
1.07
1.16
13.2
13.6
13.8
13.9
14.0
14.0
705
708
711
714
716
718
1.14
1.19
1.25
1.31
1.37
1.44
16.2
16.5
16.8
17.1
17.3
17.5
850
854
857
860
863
866
1.77
1.85
1.93
2.01
2.09
2.17
20
21
21
22
22
22
969
974
978
982
986
989
2.40
2.52
2.63
2.75
2.86
2.96
24
24
25
25
26
26
1071
1077
1083
1088
1092
1096
3.04
3.19
3.34
3.49
3.63
3.77
27
28
28
29
30
30
4800
5000
5200
5400
5600
5800
6000
6200
6400
6600
6800
7000
7200
7400
7600
7800
8000
8200
8400
8600
8800
1168
1217
1266
1314
1363
1412
1461
1509
1558
1607
1655
1704
1753
1801
1850
1899
1948
1996
2045
2094
2142
314
323
333
342
352
363
373
384
394
405
416
427
437
448
459
470
481
492
503
514
526
0.38
0.42
0.47
0.52
0.57
0.63
0.69
0.76
0.83
0.91
0.99
1.07
1.16
1.26
1.36
1.47
1.58
1.69
1.82
1.95
2.08
5.8
6.5
5.8
6.3
6.8
7.3
7.7
8.1
8.4
8.7
9.0
9.5
10.0
10.5
11.1
11.8
12.4
13.1
13.7
14.4
15.0
381
385
389
394
400
406
413
420
428
436
445
454
463
473
483
493
503
513
523
534
544
0.50
0.54
0.59
0.63
0.68
0.74
0.80
0.86
0.93
1.00
1.08
1.16
1.25
1.34
1.44
1.55
1.66
1.78
1.90
2.03
2.17
6.0
6.2
6.5
6.8
7.1
7.5
7.8
8.5
10.2
11.8
13.5
15.5
17.8
11.4
12.0
12.8
13.9
15.1
16.3
17.5
19.0
517
521
525
528
530
531
531
532
533
536
539
543
547
552
557
562
568
574
581
588
595
0.93
0.98
1.03
1.07
1.11
1.15
1.19
1.24
1.29
1.36
1.43
1.51
1.59
1.68
1.78
1.88
1.98
2.09
2.20
2.32
2.45
12.4
13.6
14.8
15.8
10.8
10.9
11.0
11.0
11.1
11.4
11.7
12.0
12.6
13.5
14.5
15.6
17.0
18.1
14.9
15.5
16.1
624
624
625
626
629
632
636
640
643
647
649
650
650
651
652
653
655
658
661
665
670
1.24
1.33
1.42
1.51
1.59
1.67
1.75
1.82
1.89
1.96
2.03
2.09
2.15
2.21
2.28
2.36
2.45
2.55
2.66
2.78
2.91
14.0
14.0
14.1
14.2
14.6
15.2
15.9
16.6
17.1
17.8
15.8
15.9
16.0
16.0
16.1
16.2
16.3
16.5
16.8
17.2
17.6
720
721
721
721
721
721
722
723
725
728
732
736
740
743
746
749
750
751
751
752
753
1.52
1.61
1.72
1.83
1.95
2.07
2.19
2.30
2.42
2.52
2.63
2.73
2.83
2.92
3.01
3.10
3.18
3.26
3.34
3.43
3.52
17.7
17.8
17.8
17.8
17.8
17.8
18.0
18.0
18.2
18.5
18.9
19.3
19.7
20
20
20
20
20
20
20
20
869
872
875
877
879
881
882
883
883
883
883
883
883
884
886
888
891
894
898
- -
- -
2.25
2.33
2.42
2.52
2.63
2.75
2.88
3.02
3.18
3.35
3.53
3.71
3.89
4.07
4.24
4.41
4.57
4.73
4.88
- -
- -
23
23
24
24
25
26
26
26
26
26
26
26
26
27
28
29
31
32
35
- -
- -
992
995
999
1002
1005
1007
1010
1013
1015
1017
1018
1019
1019
1020
- -
- -
- -
- -
- -
- -
- -
3.07
3.18
3.28
3.39
3.50
3.61
3.73
3.86
4.00
4.15
4.31
4.50
4.70
4.91
- -
- -
- -
- -
- -
- -
- -
26
27
28
28
28
29
29
30
30
31
31
32
32
32
- -
- -
- -
- -
- -
- -
- -
1100
1104
1107
1110
1113
1116
1119
1122
1125
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
3.91
4.05
4.18
4.31
4.44
4.58
4.71
4.84
4.98
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
31
31
32
32
33
33
34
34
35
- - - - - - - - - - - - -
Performance certified is for installation Type B - Free inlet, Ducted outlet. Power rating bhp does not include transmission losses.
Performance ratings do not include the effects of appurtenances (accessories). The sound ratings shown are loudness values in fan sones at 5 ft. (1.5m)
in a hemispherical free field calculated per AMCA Standard 301. Values shown are for Installation Type B: free inlet hemispherical fan sone levels.
Sone values not documented in unlisted areas. Twin unit data is derived from tests of single width fans.
9
218 - Max. 5 HP, 184T Frame 1” Shaft
9218 - Max. 5 HP, 256T Frame 1” Shaft
Wheel Dia, 18.19” Tip Speed: 4.76 X RPM = FPM
218 & 9218
CFM
3000
3200
3400
3600
3800
4000
4200
4400
4600
4800
5000
5200
5400
5600
5800
6000
6200
6400
6600
6800
7000
7200
7400
7600
OUTLET
VELOCITY
FPM
1/8” SP 1/4” SP 1/2” SP 3/4” SP 1” SP 972
1037
1102
1167
1232
1297
1362
1426
1491
1556
1621
1686
1751
1816
1881
1945
2010
2075
2140
2205
2270
2335
2399
2464
255
264
273
282
292
302
312
323
334
345
356
367
378
390
401
413
424
436
448
460
472
484
496
508
0.20
0.23
0.27
0.31
0.35
0.40
0.45
0.51
0.58
0.65
0.72
0.80
0.89
0.98
1.08
1.19
1.30
1.42
1.55
1.69
1.83
1.98
2.14
2.31
3.0
3.7
4.8
6.5
8.9
10.1
11.0
6.0
6.6
7.4
8.2
8.9
9.7
10.6
11.4
12.1
12.9
13.7
14.6
15.4
16.2
17.0
17.9
18.7
321
325
330
336
343
351
359
367
376
385
395
404
414
424
435
445
456
466
477
488
499
510
522
533
0.29
0.33
0.36
0.41
0.45
0.50
0.56
0.61
0.68
0.75
0.83
0.91
1.01
1.10
1.21
1.32
1.44
1.56
1.70
1.84
1.98
2.14
2.31
2.48
6.3
7.6
5.0
5.4
6.0
6.6
7.2
7.8
8.5
9.2
9.9
10.5
11.1
11.6
12.1
12.6
12.3
13.1
14.0
14.8
15.6
16.4
17.4
18.4
429
428
432
437
442
448
452
457
462
466
473
479
487
494
502
510
519
527
536
545
555
564
574
584
0.47
0.51
0.56
0.61
0.67
0.74
0.81
0.88
0.95
1.02
1.11
1.20
1.29
1.39
1.50
1.61
1.73
1.85
1.98
2.13
2.28
2.45
2.63
2.81
- -
- -
- -
- -
8.0
8.6
9.1
9.7
10.3
9.8
10.3
10.8
11.3
11.8
12.4
13.0
13.7
14.4
15.2
16.5
18.8
22
26
30
533
531
529
526
523
526
530
534
540
546
551
555
560
565
569
575
581
588
595
603
611
619
627
635
0.72
0.77
0.82
0.86
0.89
0.97
1.04
1.12
1.21
1.31
1.41
1.51
1.61
1.72
1.84
1.95
2.08
2.22
2.36
2.51
2.66
2.83
3.00
3.18
- -
- -
- -
- -
- -
- -
- -
- -
11.7
12.5
13.5
15.0
17.2
20
14.4
14.7
15.2
15.7
16.4
17.1
18.2
19.2
20
21
615
616
615
614
613
610
607
604
606
610
615
620
627
632
636
641
646
650
655
660
666
673
680
687
0.97
1.03
1.10
1.16
1.22
1.28
1.33
1.38
1.48
1.58
1.69
1.80
1.92
2.05
2.18
2.32
2.46
2.61
2.75
2.90
3.07
3.24
3.42
3.61
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
14.4
15.4
16.9
18.3
20
23
25
17.5
17.9
18.4
19.1
19.7
20
9218 - 2 - Max. 10 HP, 256T Frame
Wheel Dia, 18.19” 9218-2
CFM
6000
6400
6800
7200
7600
8000
8400
8800
9200
9600
10000
10400
10800
11200
11600
12000
12400
12800
13200
13600
14000
14400
14800
15200
OUTLET
VELOCITY
FPM
972
1037
1102
1167
1232
1297
1362
1426
1491
1556
1621
1686
1751
1816
1881
1945
2010
2075
2140
2205
2270
2335
2399
2464
1-1/2” SP 2” SP 2-1/2” SP
RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP S
ONES
1/8” SP 1/4” SP 1/2” SP 3/4” SP 1” SP 748
750
751
753
754
754
754
752
751
749
746
742
739
742
746
750
755
761
767
772
777
782
786
791
1.50
1.59
1.67
1.76
1.84
1.93
2.03
2.13
2.22
2.31
2.39
2.46
2.55
2.69
2.84
3.00
3.16
3.33
3.52
3.71
3.91
4.11
4.32
4.53
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
20
21
22
23
24
25
27
860
861
863
865
867
868
869
870
871
870
869
868
866
864
861
857
853
856
859
863
868
873
- -
- -
2.06
2.16
2.27
2.39
2.50
2.62
2.73
2.84
2.96
3.09
3.22
3.35
3.47
3.58
3.69
3.79
3.89
4.08
4.27
4.48
4.69
4.91
- -
- -
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
957
959
961
963
965
967
969
970
971
972
973
973
973
972
971
969
967
- -
- -
- -
- -
- -
- -
- -
2.68
2.79
2.91
3.03
3.17
3.32
3.46
3.60
3.75
3.89
4.03
4.18
4.35
4.51
4.67
4.82
4.96
- -
- -
- -
- -
- -
- -
- -
-
-
1-3/16” Shaft
Tip Speed: 4.76 X RPM = FPM
1-1/2” SP 2” SP 2-1/2” SP
RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP S
ONES
255
264
273
282
292
302
312
323
334
345
356
367
378
390
401
413
424
436
448
460
472
484
496
508
0.40
0.46
0.53
0.61
0.70
0.80
0.91
1.03
1.15
1.29
1.44
1.60
1.78
1.96
2.16
2.38
2.60
2.84
3.10
3.37
3.66
3.97
4.29
4.63
3.8
4.7
5.9
7.9
10.7
12.1
13.3
7.3
8.1
8.9
9.9
10.8
11.8
12.8
13.7
14.7
15.5
16.5
17.4
18.4
19.4
20
21
22
321
325
330
336
343
351
359
367
376
385
395
404
414
424
435
445
456
466
477
488
499
510
522
533
0.58
0.65
0.73
0.81
0.90
1.00
1.11
1.23
1.36
1.50
1.66
1.83
2.01
2.21
2.42
2.64
2.87
3.12
3.39
3.67
3.97
4.28
4.61
4.96
7.6
9.1
6.1
6.6
7.2
8.0
8.8
9.5
10.3
11.1
11.9
12.6
13.3
14.0
14.7
15.2
14.9
15.8
16.7
17.7
18.7
19.7
21
22
429
428
432
437
442
448
452
457
462
466
473
479
487
494
502
510
519
527
536
545
555
564
574
584
0.95
1.02
1.12
1.23
1.35
1.48
1.61
1.75
1.90
2.05
2.21
2.39
2.58
2.78
2.99
3.21
3.45
3.70
3.96
4.25
4.57
4.90
5.25
5.62
- - - - 9.7
10.4
11.0
11.7
12.3
12.0
12.6
13.2
13.8
14.4
15.0
15.6
16.4
17.2
18.2
19.7
23
26
32
36
533
531
529
526
523
526
530
534
540
546
551
555
560
565
569
575
581
588
595
603
611
619
627
635
1.45
1.54
1.63
1.71
1.79
1.93
2.09
2.25
2.42
2.61
2.81
3.02
3.23
3.45
3.67
3.91
4.16
4.43
4.72
5.02
5.33
5.65
5.99
6.35
- - - - - - - - - 15.1
16.2
17.9
21.0
25.0
17.0
17.5
18.1
18.9
19.6
20
22
23
24
26
615
616
615
614
613
610
607
604
606
610
615
620
627
632
636
641
646
650
655
660
666
673
680
687
1.95
2.06
2.19
2.32
2.44
2.55
2.66
2.77
2.96
3.16
3.37
3.60
3.84
4.10
4.37
4.64
4.92
5.21
5.50
5.81
6.14
6.48
6.85
7.22
- - - - - - - - - - - - 18.5
20
22
24
27
30
21
21
22
23
24
24
748
750
751
753
754
754
754
752
751
749
746
742
739
742
746
750
755
761
767
772
777
782
786
791
3.00
3.17
3.34
3.51
3.68
3.86
4.06
4.25
4.44
4.61
4.78
4.93
5.10
5.38
5.68
5.99
6.32
6.67
7.03
7.42
7.81
8.22
8.63
9.06
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
25
26
27
29
31
32
860
861
863
865
867
868
869
870
871
870
869
868
866
864
861
857
853
856
859
863
868
873
- -
- -
4.12
4.31
4.54
4.77
5.00
5.23
5.46
5.68
5.92
6.18
6.44
6.69
6.93
7.16
7.38
7.58
7.78
8.16
8.55
8.96
9.38
9.83
- -
- -
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Performance certified is for installation Type B - Free inlet, Ducted outlet. Power rating bhp does not include transmission losses.
Performance ratings do not include the effects of appurtenances (accessories). The sound ratings shown are loudness values in fan sones at 5 ft. (1.5m)
in a hemispherical free field calculated per AMCA Standard 301. Values shown are for Installation Type B: free inlet hemispherical fan sone levels.
Sone values not documented in unlisted areas. Twin unit data is derived from tests of single width fans.
10
957
959
961
963
965
967
969
970
971
972
973
973
973
972
971
969
967
- -
- -
- -
- -
- -
- -
- -
5.36
5.59
5.82
6.06
6.35
6.64
6.92
7.21
7.49
7.78
8.05
8.37
8.70
9.02
9.33
9.63
9.92
- -
- -
- -
- -
- -
- -
- -
-
-
Air Moving Products
9220 - Max. 15 HP, 256T Frame 1-716” Shaft
9220
Wheel Dia, 20.44” Tip Speed: 5.35 X RPM = FPM
CFM
6000
6250
6500
6750
7000
7250
7500
7750
8000
8250
8500
8750
9000
9250
9500
9750
10000
10250
10500
10750
11000
11250
11500
11750
12000
OUTLET
VELOCITY
FPM
1/8” SP 1/4” SP 1/2” SP 3/4” SP 1” SP 1-1/2” SP 2” SP 2-1/2” SP
RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP S
ONES
1303
1357
1411
1465
1520
1574
1628
1683
1737
1791
1845
1900
1954
2008
2063
2117
2171
2226
2280
2334
2388
2443
2497
2551
2606
336
347
358
370
381
392
404
415
427
439
450
462
474
486
498
509
521
533
545
557
568
580
592
604
616
0.84
0.94
1.04
1.15
1.27
1.40
1.54
1.68
1.84
2.00
2.18
2.36
2.56
2.77
2.98
3.21
3.45
3.70
3.96
4.23
4.52
4.82
5.13
5.46
5.80
13.3
14.7
14.4
14.1
13.8
13.6
13.5
13.3
13.3
13.3
13.3
13.3
13.3
13.4
13.5
13.6
13.7
14.0
14.6
15.2
15.8
16.9
18.7
21
24
373
382
392
402
412
423
433
444
455
465
476
487
498
510
521
532
543
555
566
578
589
601
613
624
636
1.00
1.10
1.21
1.33
1.46
1.59
1.73
1.88
2.05
2.22
2.40
2.59
2.79
3.00
3.22
3.46
3.71
3.96
4.23
4.52
4.81
5.12
5.45
5.78
6.13
9.1
9.8
10.5
11.2
11.8
12.3
12.7
13.2
13.3
13.3
13.3
13.4
13.5
13.6
13.7
14.0
14.5
15.1
15.7
16.6
18.2
20
23
26
29
446
453
461
468
476
484
492
500
509
518
528
537
547
557
567
577
587
598
608
619
629
640
651
662
673
1.35
1.46
1.58
1.71
1.85
1.99
2.14
2.30
2.47
2.65
2.84
3.05
3.26
3.48
3.72
3.97
4.22
4.49
4.78
5.07
5.38
5.70
6.04
6.38
6.75
7.6
8.0
8.5
8.9
9.4
9.8
10.3
10.7
11.2
11.8
12.4
12.9
13.5
14.1
14.8
15.7
17.0
18.9
21
24
27
31
36
41
48
511
517
523
530
536
543
551
558
565
573
581
588
596
604
613
622
631
640
650
659
669
679
689
699
709
1.75
1.87
2.00
2.13
2.28
2.42
2.58
2.75
2.94
3.13
3.33
3.54
3.76
3.99
4.23
4.48
4.75
5.04
5.33
5.64
5.96
6.29
6.64
7.00
7.37
10.0
10.3
10.6
10.5
10.9
11.4
11.9
12.3
12.8
13.4
14.0
14.5
15.1
15.7
16.8
18.0
19.5
21
23
26
29
34
36
38
39
569
574
580
585
591
597
604
610
617
624
631
638
646
653
661
668
676
684
692
700
709
718
727
736
746
2.14
2.28
2.43
2.58
2.74
2.90
3.07
3.25
3.44
3.63
3.84
4.05
4.29
4.53
4.79
5.05
5.33
5.62
5.91
6.22
6.55
6.89
7.25
7.62
8.01
11.8
12.1
12.4
12.7
13.2
13.7
14.5
14.0
14.5
15.0
15.5
16.0
16.7
17.3
18.0
19.1
20
22
23
24
25
27
28
29
30
674
678
682
685
690
695
700
705
711
716
722
728
735
741
748
754
761
768
776
783
790
798
805
813
820
2.99
3.15
3.31
3.47
3.66
3.86
4.06
4.28
4.50
4.72
4.96
5.20
5.45
5.71
5.98
6.26
6.55
6.85
7.16
7.48
7.84
8.21
8.59
8.98
9.38
16.6
17.1
18.1
18.7
19.8
21
22
24
25
27
29
31
33
36
20
21
21
22
22
23
24
24
25
26
26
765
768
772
776
780
783
787
791
795
800
805
810
815
821
827
833
839
845
851
858
864
871
878
885
892
3.86
4.06
4.26
4.46
4.67
4.88
5.09
5.31
5.55
5.81
6.08
6.36
6.64
6.94
7.24
7.55
7.87
8.20
8.54
8.90
9.26
9.63
10.01
10.41
10.81
20
20
21
21
21
22
22
22
23
23
24
25
26
27
28
29
31
32
33
34
26
27
27
28
29
845
848
852
855
859
863
867
871
874
878
882
885
890
895
900
905
910
916
921
927
933
939
946
952
958
4.75
4.95
5.19
5.43
5.68
5.93
6.19
6.45
6.71
6.97
7.24
7.51
7.83
8.15
8.49
8.84
9.19
9.56
9.93
10.32
10.71
11.12
11.53
11.96
12.40
23
24
24
24
25
25
25
26
26
26
27
27
27
28
28
29
29
30
30
31
31
32
33
33
34
9220 - Max. 40 HP, 326T Frame 2-1/4” Shaft
9220-2
Wheel Dia, 20.44” Tip Speed: 5.35 X RPM = FPM
CFM
SP x 0.249 = kPa
CFM x 0.472 = L/s
SI CONVERSION FACTOR
12000
12500
13000
13500
14000
14500
15000
15500
16000
16500
17000
17500
18000
18500
19000
19500
20000
20500
21000
21500
22000
22500
23000
23500
24000
OUTLET
VELOCITY
FPM
1303
1357
1411
1465
1520
1574
1628
1683
1737
1791
1845
1900
1954
2008
2063
2117
2171
2226
2280
2334
2388
2443
2497
2551
2606
1/8” SP 1/4” SP 1/2” SP 3/4” SP 1” SP 1-1/2” SP 2” SP 2-1/2” SP
RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP SONES RPM BHP S
ONES
336
347
358
370
381
392
404
415
427
439
450
462
474
486
498
509
521
533
545
557
568
580
592
604
616
1.69 16.0
1.88 17.9
2.09 17.3
2.31 16.9
2.55 16.6
2.80 16.3
3.08 16.2
3.37 16.1
3.68 15.9
4.01 15.7
4.36 15.9
4.73 15.9
5.12 16.0
5.53 16.1
5.97 16.2
6.42 16.4
6.90 16.6
7.40 17.1
7.92 17.8
8.47 18.4
9.04 19.1
9.64 20
10.26 22
10.91 25
11.59 28
373 2.00 11.0
382 2.21 11.8
392 2.43 12.6
402 2.66 13.3
412 2.91 14.1
423 3.18 14.7
433 3.47 15.3
444 3.77 15.8
455 4.09 15.9
465 4.43 15.9
476 4.79 16.0
487 5.17 16.1
498 5.58 16.2
510 6.00 16.4
521 6.45 16.6
532 6.92 17.1
543 7.41 17.7
555 7.93 18.3
566 8.47 19.0
578 9.03 20
589 9.63 21
601 10.25 24
613 10.89 28
624 11.57 31
636 12.27 36
446
453
461
468
476
484
492
500
509
518
528
537
547
557
567
577
587
598
608
619
629
640
651
662
673
2.70
2.92
3.16
3.42
3.69
3.97
4.27
4.59
4.94
5.30
5.69
6.09
6.52
6.97
7.44
7.93
8.45
8.99
9.55
10.14
10.76
11.40
12.07
12.77
13.50
9.2
9.6
10.3
10.8
11.3
11.9
12.5
13.1
13.7
14.3
15.1
15.7
16.4
17.1
18.0
18.9
20
22
25
29
33
38
43
50
59
511
517
523
530
536
543
551
558
565
573
581
588
596
605
613
622
631
640
650
659
669
679
689
699
709
3.50 12.1
3.74 12.5
4.00 12.9
4.27 13.0
4.55 13.3
4.85 13.9
5.16 14.5
5.50 15.0
5.87 15.5
6.26 16.2
6.66 16.8
7.08 17.4
7.52 18.1
7.97 18.9
8.45 20
8.97 22
9.51 23
10.07 25
10.66 28
11.28 31
11.92 36
12.58 41
13.28 44
14.00 47
14.75 49
569
574
580
585
591
597
604
610
617
624
631
638
646
653
661
668
676
684
692
700
709
718
727
736
746
4.29 14.4
4.57 14.7
4.86 15.0
5.16 15.4
5.47 15.9
5.80 16.5
6.15 17.3
6.51 16.9
6.88 17.4
7.27 17.9
7.67 18.6
8.09 19.2
8.57 20
9.06 21
9.58 22
10.11 23
10.66 24
11.24 26
11.83 28
12.45 29
13.10 30
13.79 32
14.50 34
15.25 35
16.02 37
674
678
682
685
690
695
700
705
711
716
722
728
735
741
748
754
761
768
776
783
790
798
805
813
820
5.99 19.8
6.30 20
6.62 22
6.95 22
7.32 24
7.72 25
8.13 27
8.55 29
8.99 31
9.45 33
9.92 35
10.40 38
10.91 41
11.43 43
11.97 24
12.53 25
13.10 25
13.70 26
14.32 27
14.96 28
15.68 28
16.41 29
17.17 30
17.96 31
18.76 32
765
768
772
776
780
783
787
791
795
800
805
810
815
821
827
833
839
845
851
858
864
871
878
885
892
7.72
8.11
8.52
8.92
9.34
9.76
10.19
10.62
11.10
11.62
12.16
12.71
13.28
13.87
14.48
15.10
15.75
16.41
17.09
17.79
18.52
19.26
20.03
20.82
21.63
24
24
25
25
25
26
26
27
27
28
29
30
31
33
34
36
37
39
40
42
31
32
33
34
34
Performance certified is for installation Type B - Free inlet, Ducted outlet. Power rating bhp does not include transmission losses.
Performance ratings do not include the effects of appurtenances (accessories). The sound ratings shown are loudness values in fan sones at 5 ft. (1.5m)
in a hemispherical free field calculated per AMCA Standard 301. Values shown are for Installation Type B: free inlet hemispherical fan sone levels.
Sone values not documented in unlisted areas. Twin unit data is derived from tests of single width fans.
11
845
848
852
855
859
863
867
871
874
878
882
885
890
895
900
905
910
916
921
927
933
939
946
952
958
9.50
9.89
10.38
10.87
11.36
11.87
12.38
12.89
13.42
13.95
14.48
15.02
15.65
16.31
16.98
17.67
18.38
19.11
19.86
20.63
21.42
22.23
23.07
23.92
24.80
28
29
29
29
30
30
31
31
31
32
32
32
33
33
34
34
35
36
36
37
38
39
40
40
41
207
Model
207
Performance curves based on tests made in
accordance with A.M.C.A. 210-85. Tested with
INDUSTRIES INC.
145T
Frame
discharge
duct. Horsepower does not include
Delhi, Ontario
drive loses. Standard air density 0.075 Lb/Cu. Ft.
Wheel Dia, 7.75” Tip Speed:
2.03
PH (519) 582 2440 X RPM = FPM
Max. 3/4 HP,
3/4” Shaft 3600
Max Wheel RPM
Shaft Diameter, In. 3/4"
3/4
Max HP
Fax (519) 582 0581
www.delhi-industries.com
Printed: October 2002
2.50
2200
2100
2.00
2000
1.75
1900
1800
1.50
1700
Curve
1500
1400
1200
3
1/
1100
2
3
P
1
H
0
6
1/
.25
1/
1000
900
800
700
600 RPM
4
.50
4
1300
2
1/
.75
3/
1.00
.00
1600
(s)
1.25
System
Static Pressure (In. wg)
2.25
4
5
6
7
8
9
10 11 12 13 14
15 16 17 18 19 20
Volume (CFM with 00's omitted)
Model 209
Max HP
3/4
209 -Max. 3/4 HP,
145T Frame
145T Frame
Wheel Dia, 10.13” 9209
9209 -Max. 1-1/2 HP,
2800
Max Wheel RPM
209
& 9209
Shaft Diameter, In. 3/4"
2800
3/4”
3/4"
1-1/2
Shaft Performance curves based on tests made in
accordance with A.M.C.A. 210-85. Tested with
discharge duct. Horsepower does not include
drive loses. Standard air density 0.075 Lb/Cu. Ft.
INDUSTRIES INC.
Delhi, Ontario
(519) 582 2.65
2440 X RPM = FPM
Tip PH
Speed:
Fax (519) 582 0581
www.delhi-industries.com
Printed: October 2002
2.50
1700
2.00
1600
1500
1.75
1400
1.50
1300
(s)
Curve
System
1100
4
1/
900
2
800
4
H
P
.25
1/
6
1/
700
600 RPM
3
1/
.50
1000
3/
.75
.00
1200
1
1.00
/2
1.25
1-1
Static Pressure (In. wg)
2.25
0
2
4
6
8
10
12
14
16
18
20
22
24
26
28
Volume (CFM with 00's omitted)
Performance certified is for installation Type B - Free inlet, Ducted outlet. Power rating bhp does not include transmission losses.
Performance ratings do not include the effects of appurtenances (accessories). The sound ratings shown are loudness values in fan sones at 5 ft. (1.5m)
in a hemispherical free field calculated per AMCA Standard 301. Values shown are for Installation Type B: free inlet hemispherical fan sone levels.
Sone values not documented in unlisted areas. Twin unit data is derived from tests of single width fans.
12
30
Air Moving Products
Model 210
Max Wheel RPM
210
& 9210
9210
Performance curves based on tests made in
accordance with A.M.C.A. 210-85. Tested with
Max. 1/2 HP,
2500 Shaft 3/4”
2500
Shaft Diameter, In. 3/4"
1-1/2
Max HP
INDUSTRIES INC.
145T
Frame
discharge
duct. Horsepower does not include
Delhi, Ontario
drive loses. Standard air density 0.075 Lb/Cu. Ft.
PH (519) 5822.99
2440 X RPM = FPM
Wheel Dia, 11.44” Tip Speed:
3/4"
1-1/2
Fax (519) 582 0581
www.delhi-industries.com
Printed: October 2002
2.50
1500
2.00
1400
1.75
1300
1.50
1200
1100
Curve
(s)
1.25
1000
System
.50
1
900
800
3 /4
.75
/2
1.00
1-1
Static Pressure (In. wg)
2.25
1/ 2
700
4
0
2
4
6
HP
.00
500 RPM
1/3
.25
1/
600
8
10 12 14 16 18 20 22 24 26 28
30 32 34 36 38 40
Volume (CFM with 00's omitted)
212 - Max. 1-1/2HP,
145T
3/4”
Shaft
Performance
curves Frame
based on tests made
in
accordance with A.M.C.A. 210-85. Tested with
INDUSTRIES INC.
duct. Frame
Horsepower does not
9212 - Max. 3 HP, discharge
145T
1”include
ShaftDelhi, Ontario
drive loses. Standard air density 0.075 Lb/Cu. Ft.
2140
2140
Max Wheel RPM
PH (519) 5823.27
2440 X RPM = FPM
Wheel
Dia,
12.50”
Tip
Speed:
3/4"
1"
Model
212
212 & 9212
9212
Shaft Diameter, In.
1-1/2
Max HP
3
Fax (519) 582 0581
www.delhi-industries.com
Printed: November 2005
2.50
1400
2.00
1300
1.75
1200
3
1.50
(s)
1100
Curve
1.25
System
1000
900
800
600
500
400 RPM
.25
0
2
4
6
1/
4
H
P
1/
3
1/
4
3/
700
.50
.00
1
.75
2
1.00
2
1/
1-
Static Pressure (In. wg)
2.25
2
8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50
Volume (CFM with 00's omitted)
Performance certified is for installation Type B - Free inlet, Ducted outlet. Power rating bhp does not include transmission losses.
Performance ratings do not include the effects of appurtenances (accessories). The sound ratings shown are loudness values in fan sones at 5 ft. (1.5m)
in a hemispherical free field calculated per AMCA Standard 301. Values shown are for Installation Type B: free inlet hemispherical fan sone levels.
Sone values not documented in unlisted areas. Twin unit data is derived from tests of single width fans.
13
215 - Max. 3 HP, Performance
184T Frame
1”made
Shaft
curves based on tests
in
accordance with A.M.C.A. 210-85. Tested with
INDUSTRIES INC.
9215 - Max. 5 HP, discharge
184T
1”include
Shaft
duct.Frame
Horsepower does not
Delhi, Ontario
drive loses. Standard air density 0.075 Lb/Cu. Ft.
1800
1800
Max Wheel RPM
Wheel Dia, 15.25” Tip Speed:
PH (519) 5823.99
2440 X RPM = FPM
Model
215
215 & 9215
9215
Shaft Diameter, In. 1"
3
Max HP
1"
5
Fax (519) 582 0581
www.delhi-industries.com
Printed: October 2002
2.50
2.00
1000
1.75
900
1.50
5
Curve
700
System
1.00
2
/2
.50
600
1
1-
.75
1
500
4
8
H
P
1/
4
0
1/
3
3/
400 RPM
.25
.00
800
(s)
1.25
3
Static Pressure (In. wg)
2.25
2
12 16 20 24 28 32 36 40 44 48 52 56
60 64 68 72 76 80
Volume (CFM with 00's omitted)
218 - Max. 5 HP,
Model
218
9218
9218 - Max. 5 HP,
Max HP
5
5
1450
1450
Max Wheel RPM
218
& 9218
1"
Shaft Diameter, In. 1"
184T Frame 1” Shaft
INDUSTRIES INC.
256T Frame 1” ShaftDelhi, Ontario
(519) 582 4.76
2440 X RPM = FPM
Wheel Dia, 18.19” Tip PH
Speed:
Performance curves based on tests made in
accordance with A.M.C.A. 210-85. Tested with
discharge duct. Horsepower does not include
drive loses. Standard air density 0.075 Lb/Cu. Ft.
Fax (519) 582 0581
www.delhi-industries.com
Printed: October 2002
2.50
900
2.00
1.75
800
1.50
700
Curve
(s)
1.25
1.00
600
.75
500
3
.50
5
System
Static Pressure (In. wg)
2.25
2
/2
1
4
2
3/
1/
.25
1
1-
400 RPM
H
P
.00
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Volume (CFM with 000's omitted)
Performance certified is for installation Type B - Free inlet, Ducted outlet. Power rating bhp does not include transmission losses.
Performance ratings do not include the effects of appurtenances (accessories). The sound ratings shown are loudness values in fan sones at 5 ft. (1.5m)
in a hemispherical free field calculated per AMCA Standard 301. Values shown are for Installation Type B: free inlet hemispherical fan sone levels.
Sone values not documented in unlisted areas. Twin unit data is derived from tests of single width fans.
14
15
Air Moving Products
Model
9220
Performance curves based on tests made in
with A.M.C.A. 210-85. Tested with
INDUSTRIES INC.
9220 - Max. 15 HP,accordance
256T
Frame
Shaft
discharge
duct. Horsepower
does not 1-716”
include
Delhi, Ontario
drive loses. Standard air density 0.075 Lb/Cu. Ft.
1325
Max Wheel RPM
Wheel
Dia, 20.44” Tip Speed:
5.35
PH (519) 582 2440 X RPM = FPM
9220
Shaft Diameter, In. 1-7/16"
15
Max HP
Fax (519) 582 0581
www.delhi-industries.com
Printed: October 2002
4.00
100
0
3.00
900
2.50
800
Curve
(s)
2.00
System
1.50
10
600
1/
72
1.00
5
500
3
400
2
4
6
2
1/
0
1
H
P
2
3/
4
300 RPM
1-
.50
.00
700
15
Static Pressure (In. wg)
3.50
8
10
12
14
16
18
Volume (CFM with 000's omitted)
Performance certified is for installation Type B - Free inlet, Ducted outlet. Power rating bhp does not include transmission losses.
Performance ratings do not include the effects of appurtenances (accessories). The sound ratings shown are loudness values in fan sones at 5 ft. (1.5m)
in a hemispherical free field calculated per AMCA Standard 301. Values shown are for Installation Type B: free inlet hemispherical fan sone levels.
Sone values not documented in unlisted areas. Twin unit data is derived from tests of single width fans.
15
20
-
523 James Street,
Delhi, Ontario N4B 2Z3 Canada
(Tel: 519-582-2440
7Fax: 519-582-0581
;www.delhi-industries.com
[email protected]
Other DELHI
Catalogues
Cat.
Cat.
Cat.
Cat.
Cat.
Cat.
Cat.
Cat.
Cat.
Cat.
Cat.
Cat.
Cat.
#SS-30_____Belt Drive Utility Blowers
#SS-31_____Forward Curved Inline Duct Blowers
#SS-32_____Forward Curved Fresh Air Supply Units
#SS-38_____Heating & Cooling Coils
#SS-43_____Forward Curved Roof Exhausters
#SS-44_____Backward Inclined DWDI Blowers
#SS-45_____Direct Drive Utility Blowers
#SS-48_____Plenum Fans
#SS-49_____Belt Drive Forward Curved DWDI Blowers
#SS-50_____Backward Inclined Square Inline Blowers
#SS-51_____Downblast Spun Aluminum Exhausters
#SS-53_____Forward Curved Direct Drive DWDI Blowers
#SS-54_____Upblast Spun Aluminum Exhausters
WARRANTY
Delhi Industries Air Moving products are guaranteed for a period of one year (12 consecutive months) from the
date of sale against manufacturing defects in material and workmanship when operating under normal conditions.
Liability is limited to the replacement of defective parts. Labour and transportation costs are not included.
If a replacement is warranted the following MUST be provided:
1.
2.
3.
Model of equipment
Date of manufacture
Original invoice reference number(s)
REPRESENTED BY:
CAT. #SS-31-7
November 2008
Printed in Canada
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement