Delfield F14 Service manual

F14 SERIES
Service and Installation Manual
Please read this manual completely before attempting to install or operate this equipment! Notify carrier of damage! Inspect all
components immediately.
Hot Food Tables
N
CAUTIO
TION
A
M
R
O
T INF
N
A
T
R
O
USE
IMP
E
R
O
F
E
ONS!
I
T
C
READ B
U
R
INST
E
S
E
H
T
AVE
S
E
S
A
E
PL
Effective April 2010
F14 Series Service and Installation Manual
Important Warning And Safety Information
WARNING Read This Manual Thoroughly Before Operating, Installing, Or Performing
Maintenance On The Equipment.
WARNING Failure To Follow Instructions In This Manual Can Cause Property Damage,
Injury Or Death.
WARNING Do Not Store Or Use Gasoline Or Other Flammable Vapors Or Liquids In The
Vicinity Of This Or Any Other Appliance.
WARNING Unless All Cover And Access Panels Are In Place And Properly Secured, Do
Not Operate This Equipment.
WARNING Allow Heated Equipment To Cool Down Before Attempting To Clean Or
Service.
WARNING Do Not Clean With Water Jet.
CAUTION Observe the following:
•
Minimum clearances must be maintained from all walls and combustible
materials.
•
Keep the equipment area free and clear of combustible material.
•
Allow adequate clearance for air openings.
•
Operate equipment only on the type of electricity indicated on the
specification plate.
•
Unplug the unit before making any repairs.
•
Retain this manual for future reference.
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
F14 Series Service and Installation Manual
Contents
Serial Number Location
Serial Number Location.........................................................3
Receiving & Inspecting..........................................................3
Specifications.........................................................................4
Installation
F14EW & F14EI (electric).................................................5
Operation
F14EI (electric).................................................................6
F14EW (electric)..............................................................6
F14GW (gas)....................................................................7
Maintenance...........................................................................8
Wiring Diagrams
Domestic U.S. F14EI (electric).........................................9
Domestic U.S. F14EW (electric).....................................10
Export F14EI (electric)...................................................11
Export F14EW (electric).................................................12
Gas Burner Assembly: F14GW Series..................................13
Delfield Food Warmer (DFW) Assemblies
with thermostatic controls.............................................14
with infinite control........................................................15
Miscellaneous Replacement Parts Lists...............................16
Standard Labor Guidelines...................................................17
Standard Warranty...............................................................18
Additional Warranty.............................................................19
The serial number on all F14 Series hot food tables is
printed on the tag located on the plate shelf.
Always have the serial number of your unit available when
calling for parts or service. A complete list of authorized
Delfield parts depots is is available at www.delfield.com.
©2010 The Delfield Company. All rights reserved. Reproduction without
written permission is prohibited. “Delfield” is a registered trademark of The
Delfield Company.
Receiving And Inspecting The Equipment
Even though most equipment is shipped crated, care should
be taken during unloading so the equipment is not damaged
while being moved into the building.
1. Visually inspect the exterior of the package and skid or
container. Any damage should be noted and reported to
the delivering carrier immediately.
2. If damaged, open and inspect the contents with the
carrier.
3. In the event that the exterior is not damaged, yet upon
opening, there is concealed damage to the equipment
notify the carrier. Notification should be made verbally
as well as in written form.
4. Request an inspection by the shipping company of the
damaged equipment. This should be done within 10
days from receipt of the equipment.
5. Check the lower portion of the unit to be sure legs or
casters are not bent.
6. Also open the compressor compartment housing and
visually inspect the refrigeration package. Be sure lines
are secure and base is still intact.
7. Freight carriers can supply the necessary damage forms
upon request.
8. Retain all crating material until an inspection has been
made or waived.
Uncrating the Equipment
First cut and remove the banding from around the crate.
Remove the front of the crate material, use of some tools will
be required. If the unit is on legs remove the top of the crate
and lift the unit off the skid. If the unit is on casters it can be
"rolled" off the skid.
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
F14 Series Service and Installation Manual
Domestic U.S Specifications
Electric with individual wells — wet or dry operation
Gas with single tank — wet operation only
Model
# Of
Openings
Amps
208V/230V
Ship Weight
Model
# Of
# Of Gas
Openings* Burners
BTU
Ship Weight
F14EI232
2
10.0/11.0
216lbs/98kg
F14GW232
2
1
20000
256lbs/116kg
F14EI348
3
15.0/16.0
296lbs/134kg
F14GW348
3
1
20000
326lbs/148kg
F14EI460
4
20.0/22.0
376lbs/170kg
F14GW460
4
1
20000
396lbs/180kg
F14EI572
5
24.0/27.0
456lbs/207kg
F14GW572
5
2
40000
456lbs/207kg
F14EI688
6
29.0/32.0
536lbs/243kg
F14GW688
6
2
40000
536lbs/243kg
Electrical connections are 208/230 volt, 60 cycle, single phase.
Each opening measures 11.87” x 19.87” (30.2cm x 50.5cm).
*Each opening measures 11.87” x 19.87” (30.2cm x 50.5cm).
Electric with single tank — wet operation only
Model
# Of
Openings
Amps
208V/240V
Ship Weight
F14EW232
2
21.0/24.0
316lbs/143kg
F14EW348
3
21.0/24.0
440lbs/199kg
F14EW460
4
21.0/24.0
500lbs/227kg
F14EW572
5
42.0/48.0
560lbs/254kg
F14EW688
6
42.0/48.0
660lbs/299kg
Electrical connections are 120/240 volt, or optional 120/208 volt.
(120 volt circuit is required for the low water cutoff.)
Export Specifications
Export Electric with individual wells — wet or dry operation
Export Gas with single tank — wet operation only
Model
# Of
Openings
240V/50Hz
Temp Class Watts
Ship Weight
Model
# Of
# Of Gas
Openings* Burners
BTU
Ship Weight
F14EI232-E
2
N
2900
216lbs/98kg
F14GW232-E
2
1
20000
256lbs/116kg
F14EI348-E
3
N
4350
296lbs/134kg
F14GW348-E
3
1
20000
326lbs/148kg
F14EI460-E
4
N
5800
376lbs/170kg
F14GW460-E
4
1
20000
396lbs/180kg
F14EI572-E
5
N
7250
456lbs/207kg
F14GW572-E
5
2
40000
456lbs/207kg
F14EI688-E
6
N
8700
536lbs/243kg
F14GW688-E
6
2
40000
536lbs/243kg
Electrical connections are 240 volt, 50 cycle, single phase.
Each opening measures 11.87” x 19.87” (30.2cm x 50.5cm).
*Each opening measures 11.87” x 19.87” (30.2cm x 50.5cm).
Export Electric with single tank — wet operation only
Model
# Of
Openings
240V/50Hz
Temp Class Watts
Ship Weight
F14EW232-E
2
N
6000
316lbs/143kg
F14EW348-E
3
N
6000
440lbs/199kg
F14EW460-E
4
N
6000
500lbs/227kg
Electrical connections are 240 volt, 50 cycle, single phase.
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
F14 Series Service and Installation Manual
Installation: F14EI & F14EW Series (Electric)
Installation should only be done by personnel certified
and licensed to install and maintain electrical
appliances.
Location
Do not install the hot food table near any combustible objects or
surfaces affected by heat or moisture.
Leveling
This unit must be level, both front and back and left to right, in order
to maintain an equal water depth throughout the wells.
Plumbing
Hot water supply connection is provided 36” (91.4cm) above the
floor, 3.12” (7.9cm) from the front left end at the rear of the unit.
You must supply the required 1/2” (1.3cm) NPT connection. The
minimum water pressure is 20psi (138kPa), the maximum water
pressure is 80psi (552kPA).
A waste connection is provided 25” (63.5cm) above the floor, 7.5”
(19.1cm) from the right end. You must supply the required 1”
(2.5cm) NPT connection.
Electrical connection
Connections must be made in accordance with all
applicable local codes and/or the National Electrical
Code. Refer to the wiring diagrams in this manual.
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
F14 Series Service and Installation Manual
Operation: F14EI Series (Electric)
Before the unit is used the first time for serving, turn the temperature
knob to “HI” and heat the well for 20 to 30 minutes. Any residue or
dust that adhered to the heater element(s) will be burned off during
this initial preheat period.
When using thick sauces, always operate the hot food well filled with
water. This will provide a more uniform temperature for the sauce.
Wet operation
1) Fill food well with 2” (50mm) of water. For quicker
pre-heating, use hot water to fill the well.
2) Turn the control to “HIGH” and pre-heat the warmer
for 30 minutes.
3) After pre-heating, set the control to your desired
serving temperature.
Steam can cause serious burns. Always wear some
type of protective covering on your hands and arms
when removing lids or pans from the unit. Lift the lid
or pan in a way that will direct escaping steam away
from your face and body.
Dry operation
Never place food directly into the well. Always use
pans.
Only 6” (15.2cm) deep insets should be used with a dry food well.
When operated dry, the bottom of the food well will discolor. A mild
abrasive cleaner is recommended to clean this discoloration.
1) Pre-heat the well on “HIGH” for approximately 15
minutes.
2) After pre-heating, set the control to your desired
serving temperature.
Although these models may be operated either with or without water
in the wells, wet operation is recommended.
Temperature
Always place covers on pans when not serving to prevent food from
drying out and to reduce your operating cost.
Product in pans . . . . . . . . . . . . . . . 140°F to 160°F (60°C to 71°C)
Water in wells . . . . . . . . . . . . . . . . 160°F to 180°F (71°C to 82°C)
For most efficient operation when empty, keep covered insets in
each well during preheating and when the well is not in use.
Do not put food down drain.
Operation: F14EW Series (Electric)
These units must be operated with 4” (102mm) minimum water in
the well. If operated dry, a low water safety switch will interrupt the
electric supply to the heater to prevent heater failure. If the low water
safety switch shuts off power, turn the control to the OFF position.
If the water level is below the heating element, allow the well to cool
completely, then refill with water. Reactivate the well by turning the
control ON and resetting to the previous temperature.
Continuous interruption of power due to a low water level may
disable the heater permanently. Pouring water on a hot heating
element will damage it.
Steam can cause serious burns. Always wear some
type of protective covering on your hands and arms
when removing lids or pans from the unit. Lift the lid
or pan in a way that will direct escaping steam away
from your face and body.
For most efficient operation, when empty, keep covered insets in
each well during preheating and when the well is not in use.
Wet operation
1) Fill food well with 4” (102mm) of water (heater must
be covered by water). For quicker pre-heating, use
hot water to fill the well.
2) Set the control to your desired serving temperature.
Temperature
Water in wells . . . . . . . . . . . . . . . . 160°F to 180°F (71°C to 82°C)
Product in pans . . . . . . . . . . . . . . . 140°F to 160°F (60°C to 71°C)
Never place food directly into the well. Always use
pans.
Always place covers on pans when not serving to
prevent food from drying out and to reduce your
operating cost.
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
F14 Series Service and Installation Manual
Operation: F14GW Series (Gas)
Lighting the pilot
Gas connection
Only qualified and trained personnel
should attempt to light the pilot. Wear
a face shield during this procedure.
Delfield is not responsible for injuries
resulting from attempts to light the pilot.
Only qualified and trained personnel should attempt
to connect the gas. Wear a face shield during this
procedure. Delfield is not responsible for injuries
resulting from attempts connect the gas.
Customer must supply the necessary connection. A pressure
regulated, 1/2” FPT. 20,000 BTU gas supply is required. A gas
regulator is supplied installed.
Be sure the connection is made to maintain flow
through the safety valve in the direction indicated by
the arrow stamped on the valve case. See the gas
burner assembly diagram on page 6.
After installation, check for leaks using a soap solution. Mix some
water with dish or other soap and supply a small amount to the
connection. If bubbles appear, the connection is not correct and
must be reinstalled before operating the unit.
The pilot valve supplied is sized for use with natural
gas. If LP gas is to be used, the pilot fitting must be
changed from the standard .021” (0.53mm) orifice to
a .011” (0.28mm) orifice. This orifice is supplied in a
plastic pouch attached to the plate shelf.
Gas hot food tables must be operated with water in the well. Dry
operation of this unit will cause distortion of the well or other serious
damage.
Steam can cause serious burns. Always wear some
type of protective covering on your hands and arms
when removing lids or pans from the unit. Lift the lid
or pan in a way that will direct escaping steam away
from your face and body.
Never place food directly into the empty well, always
use pans. Never operate burners without water in the
well.
1) Open the gas valve supplying fuel to the hot food
table
2) Push down the reset button on the pilot valve, which
is located behind the control panel, and light the
pilot.
3) Continue to hold down the reset button for 30 to 45
seconds or until the pilot continues to burn when the
button is released.
4) During the reset cycle, gas will flow to both the main
and pilot burners.
5) If the pilot is not lit after steps 1-4 have been
completed, close the gas valve and wait for at least
5 minutes before attempting to light the pilot again.
This should allow any excess gas in the air around
the unit to dissipate. If you are using LP gas, wait
at least 15 minutes; any excess gas will “fall” to the
floor and will require more time to dissipate.
Filling the well and pre-heating
1) With the drain cock closed, fill the well until
approximately a four inch depth is obtained. More
water may be required if shallow depth pans are
used. Always pour water in the well before preheating. For quicker pre-heating use hot water to fill
the well.
2) Turn the gas control knob 1/4 turn counterclockwise
and wait for the water to preheat. Then set the control
to your desired serving temperature.
Temperature
Water in wells . . . . . . . . . . . . . . . . . 160°F to 180°F (71°C to 82°C)
Product in pans . . . . . . . . . . . . . . . . 140°F to 160°F (60°C to 71°C)
Always place covers on pans when not serving to
prevent food from drying out and to reduce your
operating cost.
For most efficient operation, when empty, keep covered insets in
each well during preheating and when the well is not in use.
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
F14 Series Service and Installation Manual
Maintenance
Stainless Steel Care and Cleaning
To prevent discoloration or rust on stainless steel several
important steps need to be taken. First, we need to understand
the properties of stainless steel. Stainless steel contains 70- 80%
iron, which will rust. It also contains 12-30% chromium, which
forms an invisible passive film over the steel’s surface, which
acts as a shield against corrosion. As long as the protective
layer is intact, the metal is still stainless. If the film is broken or
contaminated, outside elements can begin to breakdown the
steel and begin to form discoloration or rust. Proper cleaning of
stainless steel requires soft cloths or plastic scouring pads.
NEVER USE
SCRAPERS!
STEEL
PADS,
WIRE
BRUSHES
OR
Cleaning solutions need to be alkaline based or non-chloride
cleaners. Any cleaner containing chlorides will damage
the protective film of the stainless steel. Chlorides are also
commonly found in hard water, salts, and household and
industrial cleaners. If cleaners containing chlorides are used be
sure to rinse repeatedly and dry thoroughly. Routine cleaning
of stainless steel can be done with soap and water. Extreme
stains or grease should be cleaned with a non-abrasive cleaner
and plastic scrub pad. Always rub with the grain of the steel.
There are stainless steel cleaners available which can restore
and preserve the finish of the steels protective layer. Early signs
of stainless steel breakdown are small pits and cracks. If this
has begun, clean thoroughly and start to apply stainless steel
cleaners in attempt to restore the passivity of the steel.
CAUTION
Never use an acid based cleaning solution! Many
food products have an acidic content, which can
deteriorate the finish. Be sure to clean the
stainless steel surfaces of ALL food products.
Common items include, tomatoes, peppers and
other vegetables.
The interior of the food wells should be cleaned daily with a nonabrasive cleaner and non-abrasive pad. If necessary, a mild
abrasive may be used on the interior of the pans only. Hard
water stains and lime scaling may require a special cleaning
product. Never use steel wool.
Never use a high-pressure water wash for
cleaning as water can damage the electrical and
gas components.
CAUTION
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
F14 Series Service and Installation Manual
Wiring Diagrams: Domestic U.S. F14EI Series
pilot light (furnished)
H1
1000 W - 120V
or 1000/1222 W 208/230 V
heating element
P
L1
L2
H2
line wires
to additional
food warmers
120 or 208-240V
SINGLE PHASE MODELS
L1
"INFINITE"
CONTROL
G
L2
infinite control
with “OFF” position
(NEUTRAL ON 120V MODELS)
HEATER 1
208-240V 3 PHASE MODELS
PILOT LIGHT
L1
HEATER 2
G
L2
L3
PILOT LIGHT
HEATER 3
PILOT LIGHT
HEATER 4
PILOT LIGHT
HEATER 5
PILOT LIGHT
HEATER 6
PILOT LIGHT
"INFINITE"
CONTROL
HEATER 1
"INFINITE"
CONTROL
HEATER 3
PILOT LIGHT
PILOT LIGHT
HEATER 4
HEATER 6
PILOT LIGHT
PILOT LIGHT
HEATER 2
PILOT LIGHT
HEATER 5
PILOT LIGHT
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
F14 Series Service and Installation Manual
Wiring Diagrams: Domestic U.S. F14EW Series
120-208 OR 120-240 VOLT SINGLE PHASE SUPPLY
Single Phase
WHITE-NEUTRAL L2-BLACK L1-RED
SWITCH
GREEN-GROUND TO CASE
BLACK
C2
WATER LEVEL
CONTROL BOARD
HEAT
POWER RELAY
120VAC COIL
RED
FILL
XL HI C
N
BLUE
PILOT LIGHT
219-4095
FLOAT
WATER FILL
SOLENOID
LOW WATER LIGHT
BLACK
BLACK
H
TEMPERATURE
CONTROL
THERMAL
OVERLOAD
ON HEATER
IMMERSION
HEATER
WHITE
RED
OPTIONAL
120-208 OR 120-240 VOLT THREE PHASE SUPPLY
Three Phase
WHITE-NEUTRAL
SWITCH
L2-BLACK L1-RED
GREEN-GROUND TO CASE
L3-BLUE
RED
C3
BLACK
WATER LEVEL
CONTROL BOARD
POWER RELAY
120VAC COIL
HEAT
FILL
L1-RED
FLOAT
L3-BLUE
L2-BLACK
XL HI C
BLUE
LOW WATER LIGHT
WHITE
N
RED
H
TEMPERATURE
CONTROL
PILOT LIGHT
219-4095
WATER FILL
SOLENOID
RED
THERMAL
OVERLOAD
ON HEATER
THREE PHASE
IMMERSION
HEATER
WHITE
OPTIONAL
10
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
F14 Series Service and Installation Manual
Wiring Diagrams: Export F14EI Series
CONTROL BOX
WIRES FROM CORD
OR BREAKER
GRN W/ YLW 16GA - #MCP00195
GRN W/ YLW 16GA - #MCP00195
L2
L2
INFINITE CONTROL
L2
INFINITE CONTROL
H2
H1
PILOT
PILOT
UNIT
PILOT LIGHT
PILOT
PILOT
L1
PILOT
PILOT LIGHT
THERMOSTAT
HEATING ELEMENT
H2
H1
L1
PILOT LIGHT
THERMOSTAT
HEATING ELEMENT
INFINITE CONTROL
H2
H1
L1
PILOT LIGHT
THERMOSTAT
HEATING ELEMENT
L2
INFINITE CONTROL
H2
H1
L1
PILOT
THERMOSTAT
HEATING ELEMENT
L2
INFINITE CONTROL
H2
H1
L1
PILOT LIGHT
THERMOSTAT
L2
INFINITE CONTROL
H2
H1
L1
PILOT LIGHT
THERMOSTAT
HEATING ELEMENT
HEATING ELEMENT
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
11
F14 Series Service and Installation Manual
Wiring Diagrams: Export F14EW Series
WATER BOARD
C
HI
XL
HEAT
FILL
H
FLOAT SWITCH
N
TERMINAL BLOCK
CONTACTOR
WEGNUT
PILOT LIGHT
HEATING ELEMENT
THERMOSTAT
H1
X2
2
1
5
4
H3
H2
TOGGLE SWITCH
X1
H4
TRANSFORMER
PILOT LIGHT
THERMAL
OVERLOAD
ON HEATER
5000W HEATER ONLY
12
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
F14 Series Service and Installation Manual
Gas Burner Assembly: F14GW Series (Single Shown)
NOTE: The same parts are used for the
double burner assembly
7
2
4
5
8
6
2
2
1
9
10
3
15 16
15
16
15
16
20
2
13
11
17
12
1
14
15
16
18
19
21
23
22
Key
Part #
Description
1
3547413
elbow 1/2” NPT
2
9321035
nut, 1/4-20
3
3547411
manifold nipple, 23”
4
3234205A
gas burner assy
5
3547409
nipple, 3/4 x 12
6
3234341
thermocouple
7
3234342
pilot assembly
8
3547329
tubing, copper, 1/4 O.D. x .028
9
3547407
pipe, manifold, valve, 12”
10
3547408
cap, 1/2 NPT
11
3547234
nipple, 1/2” x 2”
12
3234022
regulator, natural gas
13
3234023
device, vent limiting, gas reg.
14
3547406
nipple, 1/2 x 6.5”
15
9321157
u-bolt, 1/4 - 20
16
9321059
washer, 1/4
17
3234343
valve, safety
18
3234205B
chamber, air mixing
19
3234205C
plate, air mixing
20
3547593
fitting, inlet, burner (natural)
21
3234205D
cock, front handle
22
3234205E
handle, valve
23
3547591
fitting, inlet burner (LP)
24
3547412
nipple, manifold 31.25” dbl bnr only
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
13
F14 Series Service and Installation Manual
Delfield Food Well (DFW) Assembly: With Thermostatic Control
11
2
4
THERMOSTATIC
CONTROL
7
5.5
56
5.
0
Key
1
Description
XMK00100
Complete assembly, 115V, thermostat w/drain
XMK00101
Complete assembly, 115V, thermostat w/o drain
XMK00102
Complete assembly, 208V, thermostat w/drain
XMK00103
Complete assembly, 208V, thermostat w/o drain
1
GMK00061
Deflector plate
2
GMK00062
Bottom cover
3
0160014
Food well, with drain
3
0160015
Food well, without drain
4
9321353
Screw
5
2194006
Element, 115V
5
2194007
Element, 208V
6
9321379
Screws (6)
7
3434663
Insulation
8
3234556
Thermostat control knob
9
2194012
Thermostat, 200-550F
10
2194190
Pilot light, red, 115V
10
2194095
Pilot light, amber, 230V
11
GMK00063
Drain cover
12
9321353
Screws (2)
6
5
12
8.50
2.31
CLE
AR
DRAIN
OPTIONAL
3
6
NOTE: If you need four or more component parts,
you must buy a complete assembly.
9
10
14
Part #
8
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
F14 Series Service and Installation Manual
Delfield Food Well (DFW) Assembly: With Infinite Control
10
2
4
INFINITE
CONTROL
7
Key
1
9
5
8.50
2.31
CLE
AR
DRAIN
OPTIONAL
3
14
12
Description
XMK00104
Complete assembly, 115V, infinite w/drain
XMK00105
Complete assembly, 115V, infinite w/o drain
XMK00068
Complete assembly, 208V, infinite w/drain
XMK00106
Complete assembly, 208V, infinite w/o drain
1
GMK00061
Deflector plate
2
GMK00062
Bottom cover
3
0160014
Food well, with drain
3
0160015
Food well, without drain
4
9321353
Screw
5
2194006
Element, 115V
5
2194007
Element, 208V
6
9321379
Screws (2)
7
3434663
Insulation
8
2194335
Thermostat non-adjustable
9
9321007
Screw
10
GMK00063
Drain cover
11
9321007
Screws (2)
12
2194107
Infinite control, 120V
12
2194110
Infinite control, 230V
13
3234557
Infinite control knob
14
2194190
Pilot light, red, 115V
14
2194095
Pilot light, amber, 230V
8
6
11
Part #
NOTE: If you need four or more component parts, you
must buy a complete assembly.
13
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
15
F14 Series Service and Installation Manual
Miscellaneous Parts Lists
F14EI Series (Electric)
Part Description
Part #
Faucet
3234075
Gate valve 1/2”
3547486
Legs, 6” w/mounting plate
3234645
F14EW Series (Electric)
Part Description
Part #
Brass drain
3234065
Contactor, 2-pole, 220V/50Hz
TBP30021
Contactor, relay 30 amp, 120V
2194185
Faucet
3234075
Float switch
2194156
Gate valve, 1”
3547487
Immersion heater 5KW, 240V, 12.0 amps, 3-phase
2193972
Immersion heater 5KW, 208V, 24.0 amps, 1-phase
2193973
Immersion heater 5KW, 240V, 20.8 amps, 1-phase
2193974
Immersion heater 5KW, 208V, 13.9 amps, 3-phase
2193975
Knob, thermostatic control
3234556
Legs, 6” w/mounting plate
3234645
Light, pilot, 250V, amber
2194095
Relay, socket, KU12
2194133
Relay, 8501, KU12
2194132
Switch
2194400
Thermostat
2194202
Transformer
Waterlevel board
2194187
F14GW Series (Gas)
Part Description
Part #
Faucet
3234075
Gate valve 1”
3547487
Legs, 6” w/mounting plate
3234645
16
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
F14 Series Service and Installation Manual
Standard Labor Guidelines To Repair Or Replace Parts On Delfield Equipment
Advice and recommendations given by Delfield Service Technicians do not constitute or guarantee any special coverage.
•A maximum of 1-hour is allowed to diagnose a defective component.
•A maximum of 1-hour is allowed for retrieval of parts not in stock.
•A maximum travel distance of 100 miles round trip and 2-hours will be reimbursed.
•Overtime, installation/start-up, normal control adjustments, general maintenance, glass breakage, freight damage, and/or
correcting and end-user installation error will not be reimbursed under warranty unless pre-approved with a Service Work
Authorization from Delfield. You must submit the number with the service claim.
Labor Of 1-Hour Is Allowed To Replace:
•Thermostat
•Infinite Switch
•Door Jamb Switch
•Solenoid Coil
•Hi-limit/Thermal Protector Switch
•Fan Delay/Defrost Termination Switch
•Compressor Start Components and Overload Protector
•Defrost Timer
•Thermometer
•Gear Box
•
•
•
•
•
•
•
•
•
Contactor/Relay
Transformer
Evaporator/Condenser Fan Motor and Blade
Circulating Fan Motor and Blade
Microprocessor Control
Water Level Sensor/Probe
Door Hinges, Locks, and Gaskets
Condensate Element
Springs/Lowerator
Labor Of 2 Hours To Replace:
•Drawer Tracks/Cartridges
• Defrost Element
•Pressure Control
• Heating Element
•Solenoid Valve
• Locate/Repair Leak
Labor Of 3 Hours To Replace:
•EPR or CPR Valve
• Condenser or Evaporator Coil
•Expansion Valve
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
17
F14 Series Service and Installation Manual
Standard One Year Warranty (One Year Parts, 90 Days Labor)
The Delfield Company (“Delfield”) warrants to the Original Purchaser of
the Delfield product (herein called the “Unit”) that such Unit, and all
parts thereof, will be free from defects in material and workmanship
under normal use and service for a period of one (1) year from the date
of shipment of the Unit to the Original Purchaser or, if the Original
Purchaser returns the warranty card completely filled out including the
date of installation within thirty (30) days of receipt of the Unit, one (1)
year from the date of installation. During this one year warranty period,
Delfield will repair or replace any defective part or portion there of returned
to Delfield by the Original Purchaser which Delfield determines was
defective due to faulty material or workmanship. The Original purchaser
will pay all labor, crating, freight and related costs incurred in the removal
of the Unit of defective component and shipment to Delfield, except that
during a period of either ninety (90) days from the date of shipment of
the Unit to the Original Purchaser or, if the Original Purchaser returns
the warranty card completely filled out including the date of installation
within thirty (30) days of receipt of the Unit, ninety (90) days from the
date of installation Delfield will pay all related labor costs. Delfield will
pay the return costs if the Unit or part thereof was defective.
The term “Original Purchaser” as used herein means that person, firm,
association, or corporation for whom the Unit was originally installed.
This warranty does not apply to any Unit or part thereof that has been
subjected to misuse, neglect, alteration, or accident, such as accidental
damage to the exterior finish, operated contrary to the recommendations
specified by Delfield; or repaired or altered by anyone other than Delfield
in any way so as to, in Delfield’s sole judgement, affect its quality or
efficiency. This warranty does not apply to any Unit that has been moved
from the location where it was originally installed. This warranty also
does not cover the refrigerator drier or the light bulbs used in the Unit.
The warranty is subject to the user’s normal maintenance and care
responsibility as set forth in the Service and Installation Manual, such
as cleaning the condenser coil, and is in lieu of all other obligations
of Delfield. Delfield neither assumes, nor authorizes any other person
to assume for Delfield, any other liability in connection with Delfield’s
products.
Removal or defacement of the original Serial Number or Model Number
from any Unit shall be deemed to release Delfield from all obligations
hereunder or any other obligations, express or implied.
Parts furnished by suppliers to Delfield are guaranteed by Delfield only
to the extent of the original manufacturer’s express warranty to Delfield.
Failure of the Original Purchaser to receive such manufacturer’s express
warranty to Delfield. Failure of the Original Purchaser to receive such
manufacturers warranty shall in no way create any warranty, expressed
or implied, or any other obligation or liability on Delfield’s part in respect
thereof.
IF THE CUSTOMER IS USING A PART THAT RESULTS IN A VOIDED
WARRANTY AND A DELFIELD AUTHORIZED REPRESENTATIVE
TRAVELS TO THE INSTALLATION ADDRESS TO PERFORM WARRANTY
SERVICE, THE SERVICE REPRESENTATIVE WILL ADVISE CUSTOMER
THE WARRANTY IS VOID. SUCH SERVICE CALLS WILL BE BILLED
TO CUSTOMER AT THE AUTHORIZED SERVICE CENTER’S THEN
APPLICABLE TIME AND MATERIALS RATES. CONSIDER: CUSTOMER
MAY INITIATE A SERVICE AGREEMENT WITHOUT PARTS COVERAGE.
If shipment of a replacement part is requested prior to the arrival in the
Delfield factory of the part claimed to be defective, the Original Purchaser
must accept delivery of the replacement part of a C.O.D. basis, with credit
being issued after the part has been received and inspected at Delfield’s
18
plant and determined by Delfield to be within this warranty.
Under no condition does this warranty give the Original Purchaser the
right to replace the defective Unit with a complete Unit of the same
manufacturer or of another make. Unless authorized by Delfield in
writing, this warranty does not permit the replacement of any part,
including the motor-compressor, to be made with the part of another
make or manufacturer.
No claims can be made under this warranty for spoilage of any products
for any reason, including system failure.
The installation contractor shall be responsible for building access,
entrance and field conditions to insure sufficient clearance to allow any
hood(s), vent(s), or Unit(s) if necessary, to be brought into the building.
Delfield will not be responsible for structural changes or damages
incurred during installation of the Unit or any exhaust system.
Delfield shall not be liable in any manner for any default or delay in
performance hereunder caused by or resulting from any contingency
beyond Delfield’s control, including, but not limited to, war, governmental
restrictions or restraints, strike, lockouts, injunctions, fire, flood, acts
of nature, short or reduced supply of raw materials, or discontinuance
of the parts by the original part manufacturer.
Except as provided in any Additional Four Year Protection Plan,
if applicable, and the Service Labor Contract, if applicable, the
foregoing is exclusive and in lieu of all other warranties, whether
written or oral, express or implied. This warranty supersedes
and excludes any prior oral or written representations or
warranties. Delfield expressly disclaims any implied warranties
of merchantability, fitness for a particular purpose of compliance
with any law, treaty, rule or regulation relating to the discharge of
substances into the environment. The sole and exclusive remedies
of any person relating to the Unit, and the full liability of Delfield for
any breach of this warranty, will be as provided in this warranty.
Other than this Delfield Standard One Year Limited Warranty, any
applicable Delfield Additional Four Year Protection Plan or applicable
Delfield Service Labor Contract, the Original Purchaser agrees and
acknowledges that no other warranties are offered or provided in
connection with or for the unit or any other part thereof.
In no event will Delfield be liable for special, incidental or consequential
damages, or for damages in the nature of penalties.
IF DURING THE WARRANTY PERIOD, CUSTOMER USES A PART FOR
THIS DELFIELD EQUIPMENT OTHER THAN AN UNMODIFIED NEW
OR RECYCLED PART PURCHASED DIRECTLY FROM DELFIELD OR
ANY OF ITS AUTHORIZED SERVICE CENTERS AND/OR THE PART
BEING USED IS MODIFIED FROM ITS ORIGINAL CONFIGURATION,
THIS WARRANTY WILL BE VOID. FURTHER, DELFIELD AND ITS
AFFILIATES WILL NOT BE LIABLE FOR ANY CLAIMS DAMAGES OR
EXPENSES INCURRED BY THE CUSTOMER WHICH ARISE DIRECTLY
OR INDIRECTLY, IN WHOLE OR IN PART, DUE TO THE INSTALLATION
OF ANY MODIFIED PART AND/OR PART RECEIVED FROM AN
UNAUTHORIZED SERVICE CENTER. If the warranty becomes void,
Customer may purchase from Delfield, if available, a Service
Agreement or service at the then current time and materials rate.
For more information on Delfield warranty’s log on and check out the
service section of our web site at www.delfield.com.
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
F14 Series Service and Installation Manual
Additional Four Year Protection Plan
Delfield Model#
Serial #
(For Motor-Compressor Only)
Installation
Date
In addition to the Standard One Year Warranty on the MotorCompressor contained in the above listed Delfield product (the
“Unit”), The Delfield Company (“Delfield”) also agrees to repair, or
exchange with similar or interchangeable parts in design and capacity
at Delfield’s option, the defective Motor-Compressor contained in the
Unit (the “Motor-Compressor), or any part thereof, for the Original
Purchaser only, at any time during the four (4) years following the
initial one (1) year period commencing on the date of installation for the
Original Purchaser. Failure of the Original Purchaser to register the
registration card containing the Original Purchasers name, address,
date of installation, model number and serial number of the Unit
containing the Motor-Compressor within 30 days from the date of
installation shall void this warranty. This additional warranty is only
available if the Motor-Compressor is inoperative due to defects in
material or factory workmanship, as determined by Delfield in its sole
judgement and discretion. The Original Purchaser shall be responsible
for returning the defective Motor-Compressor to Delfield prepaid, F.O.B.
at the address shown on the back cover of this manual.
The term “Original Purchaser” as used herein means that person, firm,
association, or corporation for whom the Unit was originally installed.
The term “Motor-Compressor” as used herein does not include unit
base, air or water cooled condenser, receiver, electrical accessories
such as relay, capacitors, refrigerant controls, or condenser fan/motor
assembly. This warranty does not cover labor charges incidental to
the replacement of parts. This warranty further does not include
any equipment to which said condensing unit is connected, such as
cooling coils, temperature controls or refrigerant metering devices.
This warranty shall be void if the Motor-Compressor, in Delfield’s
sole judgement, has been subjected to misuse, neglect, alteration or
accident, operated contrary to the recommendations specified by the
Unit manufacturer, repaired or altered by anyone other than Delfield
in any way so as, in Delfield’s sole judgment, to affect its quality or
efficiency or if the serial number has been altered, defaced or removed.
This Warranty does not apply to a Motor-Compressor in any Unit that
has been moved from the location where it was originally installed.
The addition of methyl chloride to the condensing unit or refrigeration
system shall void this warranty.
General Conditions
Delfield shall not be liable in any manner for any default or delay in
performance hereunder caused by or resulting from any contingency
beyond Delfield’s control, including, but not limited to, war,
governmental restrictions or restraints, strike, lockouts, injunctions,
fire, flood, acts of nature, short or reduced supply of raw materials,
or discontinuance of any part or the Motor-Compressor by the unit
manufacturer.
Replacement of a defective Motor-Compressor is limited to one (1)
Motor-Compressor by us during the four (4) year period. Delfield
shall replace the Motor-Compressor at no charge.
This warranty does not give the Original Purchaser of the MotorCompressor the right to purchase a complete replacement MotorCompressor of the same make or of another make. It further does
not permit the replacement to be made with a Motor-Compressor
of another kind unless authorized by Delfield. In the event Delfield
authorizes the Original Purchaser to purchase a replacement MotorCompressor locally, only the wholesale cost of the Motor-Compressor
is refundable.
Expressly excluded from this warranty are damages resulting from
spoilage of goods.
Except as provided in any applicable Standard One Year Limited
Warranty or applicable Service Labor Contract, the foregoing is
exclusive and in lieu of all other warranties, whether written or
oral, express or implied. This Warranty supersedes and excludes
any prior oral or written representations or warranties. Delfield
expressly disclaims any implied warranties of merchantability,
fitness for a particular purpose or compliance with any law, treaty,
rule or regulation relating to the Motor-Compressor, and the full
liability of Delfield for any breach of this warranty, will be as
provided in this warranty.
Other than any applicable Delfield Standard One year Limited
Warranty, this Delfield Additional Four Year Protection Plan and any
applicable Delfield Service Labor Contract, the Original Purchaser
agrees and acknowledges that no other warranties are offered or
provided in connection with or for the Motor-Compressor or any
part thereof.
In no event will Delfield be liable for special, incidental or consequential
damages, or for damages in the nature of penalties.
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
19
Covington, TN
Mt. Pleasant, MI
Thank you for choosing Delfield!
Help is a phone call away. Help our team of professional, courteous
customer service reps by having your model number and serial number
available at the time of your call (800) 733-8829.
Model:_____________________ S/N: ____________________
Installation Date:_____________
For a list of Delfield’s authorized parts depots,
visit our website at www.delfield.com.
980 S. Isabella Rd., Mt. Pleasant, MI 48858, U.S.A. • (989) 773-7981 or (800) 733-8829 • Fax (989) 773-3210 • www.delfield.com
Delfield reserves the right to make changes in design or specifications without prior notice. ©2010 The Delfield Company. All rights reserved. Printed in the U.S.A.
DMF14 04/10