Shelleyglas Shelleysteel /Shelleysteel Service and Installation Manual

Shelleyglas Shelleysteel /Shelleysteel Service and Installation Manual
Shelleyglas
by Delfield
®
Shelleysteel
®
by Delfield
®
®
Shelleyglas /Shelleysteel
Service and Installation Manual
Please read this manual completely before attempting to install or operate this equipment!
Notify carrier of damage! Inspect all components immediately. See page 2.
Refrigerated, Heated and Non-Electrical Units
N
CAUTIO
ATION
M
R
O
F
T IN
N
A
T
R
O
USE
IMP
E
R
O
F
E
NS!
O
I
T
C
READ B
U
STR
N
I
E
S
E
E TH
V
A
S
E
S
PLEA
September 2010
Shelleyglas®/Shelleysteel™ Service and Installation Manual
Contents
Receiving & Inspecting Equipment............................................ 2
Shelleyglas Specifications........................................................3-4
Shelleysteel Specifications.......................................................5-6
Installation: Heated Units . ......................................................... 7
Operation: Heated Units.............................................................. 7
Installation: Refrigerated Units................................................... 8
Operation: LiquiTec Units............................................................ 8
Pressure Control Settings........................................................... 9
Maintenance.........................................................................10-11
Food Well Assembly.................................................................12
Wiring Diagrams..................................................................13-16
Replacement Parts List........................................................17-18
Serial Number Information
If your unit is heated, the serial tag is located above the louvered
panel near the on/off switch.
Refrigerated units have the serial tag located in the compressor
area near the on/off switch.
Understorage units often have the serial tag located on the left
inside the storage area.
All purpose counters, utility equipment or delivery carts do
not require serial numbers but a model tag is placed at the top
of the pylon on the back of the unit.
Always have the serial number of your unit available when
calling for parts or service.
This manual covers standard units only. If you have a custom
unit, consult the customer service department at the number
listed below.
Exploded Views & Replacement Parts.....................................19
Standard Labor Guidelines.......................................................20
Standard Warranties............................................................21-22
Notes.........................................................................................23
©2010 The Delfield Company. All rights reserved. Reproduction without
written permission is prohibited. “Delfield” is a registered trademarks of The
Delfield Company.
Receiving And Inspecting The Equipment
Even though most equipment is shipped crated, care should
be taken during unloading so the equipment is not damaged
while being moved into the building.
1. Visually inspect the exterior of the package and skid or
container. Any damage should be noted and reported to
the delivering carrier immediately.
2. If damaged, open and inspect the contents with the
carrier.
3. In the event that the exterior is not damaged, yet upon
opening, there is concealed damage to the equipment
notify the carrier. Notification should be made verbally
as well as in written form.
4. Request an inspection by the shipping company of the
damaged equipment. This should be done within 10
days from receipt of the equipment.
5. Check the lower portion of the unit to be sure legs or
casters are not bent.
6. Also open the compressor compartment housing and
visually inspect the refrigeration package. Be sure lines
are secure and base is still intact.
7. Freight carriers can supply the necessary damage forms
upon request.
8. Retain all crating material until an inspection has been
made or waived.
The units with LiquiTec technology cold pans contain
a non-toxic eutectic fluid within a sealed inner liner.
This fluid may leak if the tank is punctured so care
must be taken when uncrating and setting in place.
The eutectic fluid is non-toxic and may be flushed
down a disposal drain. If the LiquiTec unit cold pans
leak, immediately call the Delfield service department
directly at 1-800-733-8821 not your local service
agent.
Uncrating the Equipment
First cut and remove the banding from around the crate.
Remove the front of the crate material, use of some tools will
be required. If the unit is on legs remove the top of the crate
as well and lift the unit off the skid. If the unit is on casters it
can be "rolled" off the skid.
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
Shelleyglas®/Shelleysteel™ Service and Installation Manual
Shelleyglas® Specifications
This manual covers standard units only. If you have a custom unit, consult the customer service department at the number listed below.
Heated Serving Counters
Model
V/ Hz/Ph
NEMA Plug
Amperage
KH-2
120/208-230/60/1
14-20P
15.0
KH-3
120/208-230/60/1
14-30P
20.0
KH-4
120/208-230/60/1
14-50P
26.0
KH-5
120/208-230/60/1
14-50P
31.0
KH-6
120/208-230/60/1
14-50P
37.0
KH-2-NU
120/208-230/60/1
14-20P
11.0
KH-3-NU
120/208-230/60/1
14-20P
16.0
KH-4-NU
120/208-230/60/1
14-30P
22.0
KH-5-NU
120/208-230/60/1
14-50P
28.0
KH-6-NU
120/208-230/60/1
14-50P
33.0
V/ Hz/Ph
NEMA Plug
Amperage
H.P.
Refrigerant
BTU
KCSC-36B
115/60/1
5-15P
7.0
1/4
404a
1102
KCSC-50B
115/60/1
5-15P
7.0
1/4
404a
1240
KCSC-60B
115/60/1
5-15P
7.0
1/4
404a
1343
KCSC-74B
115/60/1
5-15P
7.0
1/4
404a
1423
KCSC-96B
115/60/1
5-15P
7.0
1/4
404a
1487
V/ Hz/Ph
NEMA Plug
Amperage
H.P.
Refrigerant
BTU
KCSC-36-EF
115/60/1
5-15P
7.0
1/4
404a
1102
KCSC-50-EF
115/60/1
5-15P
7.0
1/4
404a
1240
KCSC-60-EF
115/60/1
5-15P
7.0
1/4
404a
1343
KCSC-74-EF
115/60/1
5-15P
7.0
1/4
404a
1423
KCSC-96-EF
115/60/1
5-15P
7.0
1/4
404a
1487
Refrigerated Cold Pan Serving Counters
Model
Shelleyglas with LiquiTec
Model
Heated and Refrigerated Combo Counters
Model
V/ Hz/Ph
NEMA Plug
Amperage
H.P.
Refrigerant
BTU
KHCR-50-B
120/60/1
5-20P
16.0
1/4
404a
1102
KHCR-60-B
120/60/1
5-20P
16.0
1/4
404a
1102
KHCR-74-B
120/60/1
5-20P
16.0
1/4
404a
1102
KHCR-96-B
120/60/1
5-20P
16.0
1/4
404a
1240
KH2CR-72-B
120/208-230/60/1
14-30P
18.0
1/4
404a
1102
KH2CR-96-B
120/208-230/60/1
14-30P
18.0
1/4
404a
1343
KH3CR-96-B
120/208-230/60/1
14-30P
23.0
1/4
404a
1240
KH4CR-96-B
120/208-230/60/1
14-50P
29.0
1/4
404a
1102
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
Shelleyglas®/Shelleysteel™ Service and Installation Manual
Shelleyglas® Specifications, continued
Heated and Ice Cooled Combo Counters
Model
V/ Hz/Ph
NEMA Plug
Amperage
KHC-50-NU
120/60/1
5-15P
9.0
KHC-60-NU
120/60/1
5-15P
9.0
KHC-74-NU
120/60/1
5-15P
9.0
KHC-96-NU
120/60/1
5-15P
9.0
KH2C-74-NU
120/208-230/60/1
14-20P
11.0
KH2C-96-NU
120/208-230/60/1
14-20P
11.0
KH3C-74-NU
120/208-230/60/1
14-20P
16.0
KH3C-96-NU
120/208-230/60/1
14-20P
16.0
KH4C-96-NU
120/208-230/60/1
14-30P
22.0
V/ Hz/Ph
NEMA Plug
Amperage
H.P.
Refrigerant
KCFT-36-NU
115/60/1
5-15P
7.0
1/4
404a
435
KCFT-50-NU
115/60/1
5-15P
7.0
1/4
404a
595
KCFT-60-NU
115/60/1
5-15P
7.0
1/4
404a
717
KCFT-74-NU
115/60/1
5-15P
7.0
1/4
404a
827
KCFT-96-NU
115/60/1
5-15P
7.0
1/4
404a
921
Frost Top Serving Counters
Model
BTU
Milk Counters
Model
V/ Hz/Ph
NEMA Plug
Amperage
H.P.
Refrigerant
BTU
KCM-36
115/60/1
5-15P
7.0
1/4
404A
1114
KCM-50
115/60/1
5-15P
7.0
1/4
404A
1190
KCM-60
115/60/1
5-15P
7.0
1/4
404A
1329
KCM-74
115/60/1
5-15P
7.0
1/4
404A
1535
V/ Hz/Ph
NEMA Plug
Amperage
H.P.
Refrigerant
BTU
KCF-36
115/60/1
5-15P
7.0
1/4
404A
915
KCF-50
115/60/1
5-15P
7.0
1/4
404A
1350
KCF-60
115/60/1
5-15P
8.0
1/3
404A
1456
KCF-74
115/60/1
5-15P
8.0
1/3
404A
1609
V/ Hz/Ph
NEMA Plug
Amperage
H.P.
Refrigerant
Ice Cream Counters
Model
Milk and Ice Cream Counters
Model
BTU
REF/FRZ
KCFM-50
115/60/1
5-15P
7.0
1/4
404A
789/1580
KCFM-74
115/60/1
5-15P
8.0
1/3
404A
1199/2040
Model
V/ Hz/Ph
NEMA Plug
Amperage
KRB
115/60/1
5-15P
5.0
Carving Counter
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
Shelleyglas®/Shelleysteel™ Service and Installation Manual
Shelleysteel® Specifications
Heated Serving Counters
Model
V/Hz/Ph
NEMA Plug
Amperage
SH-2
120/208-230/60/1
14-20P
15.0
SH-3
120/208-230/60/1
14-30P
20.0
SH-4
120/208-230/60/1
14-50P
26.0
SH-5
120/208-230/60/1
14-50P
31.0
SH-6
120/208-230/60/1
14-50P
37.0
SH-2-NU
120/208-230/60/1
14-20P
11.0
SH-3-NU
120/208-230/60/1
14-20P
16.0
SH-4-NU
120/208-230/60/1
14-30P
22.0
SH-5-NU
120/208-230/60/1
14-50P
28.0
SH-6-NU
120/208-230/60/1
14-50P
33.0
Refrigerated Cold Pan Serving Counters
Model
V/Hz/Ph
NEMA Plug
Amperage
H.P.
Refrigerant
BTU
SCSC-36B
115/60/1
5-15P
7.0
1/4
404a
1102
SCSC-50B
115/60/1
5-15P
7.0
1/4
404a
1240
SCSC-60B
115/60/1
5-15P
7.0
1/4
404a
1343
SCSC-74B
115/60/1
5-15P
7.0
1/4
404a
1423
SCSC-96B
115/60/1
5-15P
7.0
1/4
404a
1487
Shelleysteel with LiquiTec
Model
V/Hz/Ph
NEMA Plug
Amperage
H.P.
Refrigerant
BTU
SCSC-36-EF
115/60/1
5-15P
7.0
1/4
404a
1102
SCSC-50-EF
115/60/1
5-15P
7.0
1/4
404a
1240
SCSC-60-EF
115/60/1
5-15P
7.0
1/4
404a
1343
SCSC-74-EF
115/60/1
5-15P
7.0
1/4
404a
1423
SCSC-96-EF
115/60/1
5-15P
7.0
1/4
404a
1487
Heated and Refrigerated Combo Counters
Model
V/Hz/Ph
NEMA Plug
Amperage
H.P.
Refrigerant
BTU
SHCR-50-B
120/60/1
5-20P
16.0
1/4
404a
1102
SHCR-60-B
120/60/1
5-20P
16.0
1/4
404a
1102
SHCR-74-B
120/60/1
5-20P
16.0
1/4
404a
1102
SHCR-96-B
120/60/1
5-20P
16.0
1/4
404a
1240
SH2CR-62-B
120/208-230/60/1
14-20P
16.0
1/4
404a
1423
SH2CR-72-B
120/208-230/60/1
14-30P
18.0
1/4
404a
1102
SH2CR-96-B
120/208-230/60/1
14-30P
18.0
1/4
404a
1343
SH3CR-96-B
120/208-230/60/1
14-30P
23.0
1/4
404a
1240
SH4CR-96-B
120/208-230/60/1
14-50P
29.0
1/4
404a
1102
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
Shelleyglas®/Shelleysteel™ Service and Installation Manual
Shelleysteel® Specifications, continued
Heated and Ice Cooled Combo Counters
Model
V/Hz/Ph
NEMA Plug
Amperage
SHC-50-NU
120/60/1
5-15P
9.0
SHC-60-NU
120/60/1
5-15P
9.0
SHC-74-NU
120/60/1
5-15P
9.0
SHC-96-NU
120/60/1
5-15P
9.0
SHC2-62-NU
120/208-230/60/1
14-20P
11.0
SH2C-74-NU
120/208-230/60/1
14-20P
11.0
SH2C-96-NU
120/208-230/60/1
14-20P
11.0
SH3C-74-NU
120/208-230/60/1
14-20P
16.0
SH3C-96-NU
120/208-230/60/1
14-20P
16.0
SH4C-96-NU
120/208-230/60/1
14-30P
22.0
Frost Top Serving Counters
Model
V/Hz/Ph
NEMA Plug
Amperage
H.P.
Refrigerant
BTU
SCFT-36-NU
115/60/1
5-15P
7.0
1/4
404a
435
SCFT-50-NU
115/60/1
5-15P
7.0
1/4
404a
595
SCFT-60-NU
115/60/1
5-15P
7.0
1/4
404a
717
SCFT-74-NU
115/60/1
5-15P
7.0
1/4
404a
827
SCFT-96-NU
115/60/1
5-15P
7.0
1/4
404a
921
Milk Counters
Model
V/Hz/Ph
NEMA Plug
Amperage
H.P.
Refrigerant
BTU
SCM-36
115/60/1
5-15P
7.0
1/4
404A
1114
SCM-50
115/60/1
5-15P
7.0
1/4
404A
1190
SCM-60
115/60/1
5-15P
7.0
1/4
404A
1328
SCM-74
115/60/1
5-15P
7.0
1/4
404A
1535
Ice Cream Counters
Model
V/Hz/Ph
NEMA Plug
Amperage
H.P.
Refrigerant
BTU
SCF-36
115/60/1
5-15P
7.0
1/4
404A
915
SCF-50
115/60/1
5-15P
7.0
1/4
404A
1350
SCF-60
115/60/1
5-15P
8.0
1/3
404A
1456
SCF-74
115/60/1
5-15P
8.0
1/3
404A
1609
Model
V/Hz/Ph
NEMA Plug
Amperage
H.P.
Refrigerant
BTU
REF/FRZ
SCFM-50
115/60/1
5-15P
7.0
1/4
404A
789/1580
SCFM-74
115/60/1
5-15P
8.0
1/3
404A
1199/2040
Model
V/Hz/Ph
NEMA Plug
Amperage
SRB
115/60/1
5-15P
5.0
V/Hz/Ph
NEMA Plug
Amperage
208-230/60/1
14-30P
22.0
Milk and Ice Cream Counter
Carving Counter
Trimline L-shaped Heated Serving Counter
Model
SLT4 (-L OR -R)
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
Shelleyglas®/Shelleysteel™ Service and Installation Manual
Installation: Heated Units
Electrical Connections
Location
Do not install the unit near combustible objects or surfaces
affected by heat or moisture.
Leveling
The unit must be level, both front and back and left to right,
in order to maintain an equal water depth throughout the
wells.
onnections must be made in accordance with all
C
applicable local codes and/or the National Electrical
Code. Refer to the amperage data on page 3 and
the wiring diagrams on pages 8 and 9. A standard
unit is provided with a power cord and 3-prong
grounded plug. All units should be plugged into a
grounded receptacle with its own circuit protection
that matches the amperage of the plug.
Operation: Heated Units
After plugging in the power supply cord, select desired
temperature by rotating the knob on the temperature control
panel. Indicator light will come on when the switch is
activated. Individual temperature control knobs and indicator
lights are provided for each heated food well.
control at “High”. With pans in place, wells will boil water.
Food temperature will vary depending on type and amount of
product. To minimize steam and water usage, set control to
lowest setting that will maintain proper food temperature.
If the same temperature settings for each well are used every
day, the temperature knobs can be left in their set position
and the wells can be turned off using the ON/OFF switch at
the end of the control panel.
Steam can cause serious burns. Always wear
some type of protective covering on your hands
and arms when removing lids from the unit. Lift
the lid in a way that will direct escaping steam
away from your face and body. Water temperature
will average 180˚F.
Before the unit is used the first time for serving, turn the
temperature knob to “10” and heat the well for 15 minutes.
Do not be alarmed if smoke appears; this preheat should
burn off any residue or dust that has adhered to the food well
element.
When serving thick sauces always use the hot food well in
“wet” operation. This provides more uniform temperature for
the sauce. Product temperature should range from 140˚F to
160˚F
ever place food directly in well. Always use
N
pans.
To reduce preheating time, use hot water to fill the well.
Dry operation
Wet operation is usually much more efficient and is usually
preferred. However, these units may be operated without
water with no damage to the unit.
T he dry well should never be preheated longer
than 15 minutes. Only 6” deep pans should be
used with dry food wells.
hen operated dry, the well bottoms become very
W
hot. Do not allow unprotected skin to contact any
well surface.
For most efficient operation, keep covered insets
empty in each well during preheating and when the well is not
in use.
When operated dry, the bottom of the well will discolor. To
clean, use a stainless steel cleaner or mild abrasive.
Always place covers on pans when not serving to prevent
food from drying out and to reduce your operating costs.
Operation of optional heated understorage
Wet operation
Fill the food well with about two inches of water and cover
with lid or empty pan. To preheat water, set temperature
If necessary, preheat the heated understorage to desired
temperature. Temperature range of understorage is 100°F to
200°F. The temperature control knob is always the far left knob
on the panel. Indicator light is also at the far left.
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
Shelleyglas®/Shelleysteel™ Service and Installation Manual
Installation: Refrigerated Units
Location
Be sure the location chosen has a floor strong enough to
support the total weight of the cabinet and contents. Reinforce
the floor as necessary to provide for maximum loading.
garden hose. Units on legs with optional remote drain valve
handle will have 1” threaded pipe extending from bottom of
unit. On standard units, a stainless steel access panel or hinged
louver will be provided for access to drain connections.
For the most efficient refrigeration, be sure to provide good
air circulation inside and out.
Inside cabinet: Do not pack unit so full that air cannot
circulate. Take care not to block air flow to the fans and allow
space along the sides.
Outside cabinet: Be sure the unit has access to ample air;
avoid hot corners and locations near stoves and ovens. It
is suggested the rear of the unit be no less than two inches
from any wall, partition or any other object which will restrict
exhaust air flow.
CAUTION
Electrical connection
A standard refrigerated unit is provided with a power cord and
3-prong grounded plug.
The unit should be plugged into a receptacle with its own
circuit protection that matches the amperage of the plug.
Refer to the amperage data on page 3 or the
serial tag data and your local code or the National
Electrical Code to be sure the unit is connected
to the proper power source. A protected circuit
of the correct voltage and amperage must be run
for connection of the supply cord or permanent
connection to the unit.
Leveling
A level cabinet looks better and will perform better because
the doors will line up with the door frames properly, and the
cabinet will not be subject to unnecessary strain.
Stabilizing
Some models are supplied on casters for your convenience,
for ease of cleaning underneath and mobility.
n cord-connected units, an ON/OFF switch is
O
located directly on the face of the compressor
section. The switch must be turned to its OFF
position and power supply disconnected whenever
doing the following:
T he unit must be installed in a stable condition
with the front wheels locked, locking the front
casters after installation is the owner’s and
operator’s responsibility.
Plumbing
Refrigerated units have a drain that exits the unit on the bottom,
and is located on the operator’s left side. Standard units on
casters or legs will have a bronze faucet that fits a standard
Moisture collecting from improper drainage can
create a slippery surface on the floor and a hazard
to employees. It is the owner’s and operator’s
responsibility to provide a container or outlet for
drainage.
1.
Performing maintenance functions.
2.
Cleaning the refrigerated cabinet area.
3.
Performing service or repair functions.
nder no circumstances should the unit be operated without
U
the louvered panel in place.
Operation: LiquiTec Units
LiquiTec Series cold pans are adjusted at the factory to
provide satisfactory operation without any further adjustments.
However, if it is necessary to adjust the temperature, the control
is located in the machine compartment. Turn the knob clockwise
as indicated on the control. Settings are from 1 through 7;
7 being the coldest. Adjustments should be made gradually.
Several small adjustments will be more effective than one
large adjustment. It may take an hour or longer to realize the
temperature change depending on the application and location
of the unit.
These units are not designed to cool warm food products. Items
should be placed in the unit pre-cooled at least to the desired
holding temperature, if not slightly colder. In some applications,
a gradual warming of product may occur, particularly at the
exposed top of the products. Stirring or rotation of the product
may be necessary to maintain overall temperature. Warming of
food product can occur very quickly outside of the unit. When
loading or rotating the product, avoid leaving food items in
a non-refrigerated location for any length of time to prevent
warming or spoilage.
The cold pan is not intended to be used with ice.
The unit has an ON/OFF switch. Turn the unit ON an hour prior
to use to allow for ample cool down time. The unit must be
turned off when not in use or overnight for defrosting and
cleaning.
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
Shelleyglas®/Shelleysteel™ Service and Installation Manual
Pressure Control Settings
All Delfield refrigerated models come equipped with 115-volt,
60 cycle, single phase refrigeration units. The refrigeration
valves are open and ready to operate as soon as the power
supply cord is plugged into the standard 115-volt, grounded
electrical outlet.
Pressure Control
The temperature is controlled by an adjustable pressure
control located in the machine compartment. An adjustable
control has the word COLDER near the knob, with an arrow
to indicate the adjustment direction. These controls are
field adjustable and do not require a service agent. If you
have any questions, feel free to contact the Delfield Service
Department.
I n attempting to adjust the pressure control,
you can do damage to your unit by accidentally
adjusting the differential. Please make small
incremental adjustments if a temperature
adjustment is necessary, please contact the
service department at Delfield (800) 733-8821
or your local service agent. Delfield is not
responsible for charges incurred while having
the pressure control adjusted.
Pressure control settings:
KCSC/SCSC, KHCR/SHCR & KCFT/SCFT
55# cut in 30# cut out
KCM/SCM
40# cut in 20# cut out
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
Shelleyglas®/Shelleysteel™ Service and Installation Manual
Maintenance
Drain Maintenance - Base
Each unit has a drain located inside the unit that removes
the condensation from the evaporator coil and routes it to an
external condensate evaporator pan. Each drain can become
loose or disconnected during normal use. If you notice water
accumulation on the inside of the unit be sure the drain tube
is connected to the evaporator drain pan. If water is collecting
underneath the unit make sure the end of the drain tube is in
the condensate evaporator in the machine compartment. The
leveling of the unit is important as the units are designed to
drain properly when level. Be sure all drain lines are free of
obstructions.
Caster Maintenance
Wipe casters with a damp cloth monthly to prevent corrosion.
The power switch must be turned to OFF and the
unit disconnected from the power source whenever
performing service, maintenance functions or
cleaning the refrigerated area.
Interiors & Exteriors
The interior and exterior can be cleaned using soap and warm
water. If this isn’t sufficient, try ammonia and water or a
nonabrasive liquid cleaner. When cleaning the exterior, always
rub with the “grain” of the stainless steel to avoid marring the
finish. Do not use an abrasive cleaner because it will scratch the
stainless steel and can damage the breaker strips and gaskets.
For all fiberglass and stainless steel parts, use a mild, nonabrasive soap or detergent and warm water. This may be
followed by an application of stainless steel cleaner or polish
which will eliminate water spotting, fingerprints and bring out
the color of the fiberglass. To maintain the rich, brilliant color
of the fiberglass and to remove shallow surface scratches, wax
twice a year. This can be done in the same manner in which a
car is waxed.
Stainless Steel Care and Cleaning
To prevent discoloration or rust on stainless steel several
important steps need to be taken. First, we need to understand
the properties of stainless steel. Stainless steel contains 70- 80%
iron, which will rust. It also contains 12-30% chromium, which
forms an invisible passive film over the steel’s surface, which
acts as a shield against corrosion. As long as the protective
layer is intact, the metal is still stainless. If the film is broken
or contaminated, outside elements can begin to breakdown the
steel and begin to form discoloration or rust. Proper cleaning of
stainless steel requires soft cloths or plastic scouring pads.
NEVER USE STEEL PADS, WIRE BRUSHES OR SCRAPERS!
10
Cleaning solutions need to be alkaline based or non-chloride
cleaners. Any cleaner containing chlorides will damage
the protective film of the stainless steel. Chlorides are also
commonly found in hard water, salts, and household and
industrial cleaners. If cleaners containing chlorides are used be
sure to rinse repeatedly and dry thoroughly. Routine cleaning
of stainless steel can be done with soap and water. Extreme
stains or grease should be cleaned with a non-abrasive cleaner
and plastic scrub pad. Always rub with the grain of the steel.
There are stainless steel cleaners available which can restore
and preserve the finish of the steels protective layer. Early signs
of stainless steel breakdown are small pits and cracks. If this
has begun, clean thoroughly and start to apply stainless steel
cleaners in attempt to restore the passivity of the steel.
Never use an acid based cleaning solution! Many
food products have an acidic content, which can
deteriorate the finish. Be sure to clean the stainless
steel surfaces of ALL food products. Common items
include, tomatoes, peppers and other vegetables.
Cleaning the Condenser Coil
In order to maintain proper refrigeration performance, the
condenser fins must be cleaned of dust, dirt and grease
regularly. It is recommended that this be done at least every
three months. If conditions are such that the condenser is totally
blocked in three months, the frequency of cleaning should be
increased. Clean the condenser with a vacuum cleaner or stiff
brush. If extremely dirty, a commercially available condenser
cleaner may be required.
Failure to maintain a clean condenser coil can initially cause high
temperatures and excessive run times. Continuous operation
with a dirty or clogged condenser coil can result in compressor
failure. Neglecting the condenser coil cleaning procedures will
void any warranties associated with the compressor and cost
to replace the compressor.
Never use a high-pressure water wash for this
cleaning procedure as water can damage the
electrical components located near or at the
condenser coil.
Doors/Hinges
Over time and with heavy use doors the hinges may become
loose. If this happens tighten the screws that mount the hinge
brackets to the frame of the unit. Loose or sagging doors can
cause the hinges to pull out of the frame, which may damage
both the doors and the hinges. In some cases this may require
qualified service agents or maintenance personnel to perform
repairs.
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
Shelleyglas®/Shelleysteel™ Service and Installation Manual
Maintenance, continued
Do not place hot pans on/against the blue ABS liner.
Do not throw items into the storage area. Failure
to follow these recommendations could result in
damage to the interior of the cabinet or to the blower
coil. Overloading the storage area, restricting the
airflow, and continuous opening and closing of the
doors and drawers will hamper the units ability to
maintain operational temperature.
Preventing blower coil corrosion
To help prevent corrosion of the blower coil, store all acidic
items, such as pickles and tomatoes, in sealable containers.
Immediately wipe up all spills.
Units with pans should be operated with pans in
place. Operating the unit without all pans in place
will lower efficiency and may damage the unit.
Continuous opening and closing of the doors will hamper the
unit’s ability to maintain optimum refrigeration temperature.
Top section is not intended for overnight storage. Product
should be removed from pans. Pans can remain in unit while
empty.
Defrosting
Refrigerated cold pans and frost tops should be defrosted daily.
Milk or Ice Cream dispensers require defrosting after 3/8 to 1/2
of frost forming. On/Off switch located above louver panel.
Never use sharp objects or tools to clean or scrape
ice/frost build up from the refrigerated cold pans
or frost tops. A puncture to the pan could cause
irreparable damage to the refrigeration system.
Units with a Eutectic Fluid Cold Pan require the
same precautions. The fluid is NOT refillable
and loss of fluid due to a puncture would cause
irreparable damage.
Over shelves and other items mounted to the top of the counters
should never be installed in the field due to the potential damage
to the refrigeration system.
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
11
Shelleyglas®/Shelleysteel™ Service and Installation Manual
Food Well Assembly — KH/SH/-NU Series with Infinite Controls
No.
7
3
6
5
7
KNOB, INFINITE CONTROL
6
INSULATION, BLANKET
5
THERMOSTAT, NON-ADJ, 550oF
4
ELEMENT, HEATING, 208/230V,1000/1222W
ELEMENT, HEATING, 120V/1000W
3
PLATE, DEFLECTOR, DFW, W/O DRAIN
4
PLATE, DEFLECTOR, DFW, W/DRAIN
2
2
Part Description
2
INSULATION, FIBERGLASS, 9" X 48"
1
FOOD WELL W/STRAPS, ASSY, WO/ DRAIN
FOOD WELL W/STRAPS, W/ DRAIN
1
208/230V
—
CONTROL, INFINITE, 240V, 13A
—
CONTROL, INFINITE, 120V, 13A
NOTE: See page 18 for part numbers
12
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
Shelleyglas®/Shelleysteel™ Service and Installation Manual
Wiring Diagram — Units With Infinite and Thermostatic Controls
NEUTRAL WIRE FOR 120 VOLT OPTIONS
(DPST SWITCH)
MASTER ON/OFF SWITCH 1
NEUTRAL
L2
L1
PILOT LIGHT
INFINITE CONTROL
L2
H2
L1
P
H1
GND
LIMIT SWITCH
HEATER
120/208-240V-37A-1PH
NEMA #14-50P CORD/PLUG SUPPLIED
FOOD WELL
PILOT LIGHT
INFINITE CONTROL
H2
L2
L1
P
HL
OFF L
O
LIMIT SWITCH
HEATER
FOOD WELL
2
5
1
6
HI
3
PILOT LIGHT
INFINITE CONTROL
H2
L2
L1
P
H1
LIMIT SWITCH
HEATER
(DPST SWITCH)
MASTER ON/OFF SWITCH 2
FOOD WELL
PILOT LIGHT
INFINITE CONTROL
H2
L2
L1
P
H1
LIMIT SWITCH
HEATER
FOOD WELL
PILOT LIGHT
INFINITE CONTROL
H2
L2
L1
P
H1
LIMIT SWITCH
HEATER
FOOD WELL
PILOT LIGHT
INFINITE CONTROL
H2
L2
L1
P
H1
LIMIT SWITCH
HEATER
FOOD WELL
OFF
1
10
L2
7
3
2
9 8
PILOT LIGHT
L1
HEATER
6
5 4
THERMOSTAT
HEATED UNDERSTORAGE
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
13
4
Shelleyglas®/Shelleysteel™ Service and Installation Manual
Wiring Diagram — Units With Infinite Controls
NEUTRAL WIRE FOR 120 VOLT OPTIONS
NEUTRAL
(DPST SWITCH)
MASTER ON/OFF SWITCH 1
L2
L1
PILOT LIGHT
GND
L2
L1
P
INFINITE CONTROL
H2
H1
LIMIT SWITCH
HEATER
120/208-240V-33A-1PH
NEMA #14-50P CORD/PLUG SUPPLIED
FOOD WELL
PILOT LIGHT
L2
L1
P
OFF L
O
HI
INFINITE CONTROL
H2
HL
HEATER
6
1
FOOD WELL
2
5
LIMIT SWITCH
3
4
PILOT LIGHT
L2
L1
P
(DPST SWITCH)
MASTER ON/OFF SWITCH 2
INFINITE CONTROL
H2
H1
LIMIT SWITCH
HEATER
FOOD WELL
PILOT LIGHT
L2
L1
P
INFINITE CONTROL
H2
H1
LIMIT SWITCH
HEATER
FOOD WELL
PILOT LIGHT
L2
L1
P
INFINITE CONTROL
H2
H1
LIMIT SWITCH
HEATER
FOOD WELL
PILOT LIGHT
L2
L1
P
INFINITE CONTROL
H2
H1
LIMIT SWITCH
HEATER
14
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
Shelleyglas®/Shelleysteel™ Service and Installation Manual
Wiring Diagram — Cold Pan Combo
CONDENSER FAN
S
C
L1
R
COMPRESSOR
115V
PRESSURE CONTROL
N
RECEPTACLE FOR OPTIONAL
LOW VOLTAGE COOLING FANS
G
PLEASE REFER TO PAGES 8 AND 9 FOR INFORMATION ON THE
HOT PAN SECTION OF COMBINATION MODELS.
Wiring Diagram — kcsc, scsc, kcft And scft Cold Pans
L1
N
G
ON/OFF
SWITCH
CONDENSING UNIT
RECEPTACLE FOR OPTIONAL
LOW VOLTAGE COOLING FANS
ON COLD PANS
ONLY. NOT
AVAILABLE ON
FROST TOP
UNITS.
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
15
Shelleyglas®/Shelleysteel™ Service and Installation Manual
Wiring Diagram — kcfm, scfm
ON/OFF
SWITCH
SOL
THERMOSTAT
LOW PSI
COMPRESSOR
S
C
R
CONDENSER FAN
Wiring Diagram — kcf, scf, KCM, SCM
ON/OFF
SWITCH
LOW PSI
COMPRESSOR
S
C
R
CONDENSER FAN
UNITS SUPPLIED WITH EVAPORATOR PRESSURE REGULATOR
16
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
Shelleyglas®/Shelleysteel™ Service and Installation Manual
Replacement Parts List
Heated Serving Counters
Part Number
Description
KH/SH-2 KH/SH-3 KH/SH-4 KH/SH-5 KH/SH-6 KH/SH-2-NU KH/SH-3-NU KH/SH-4-NU KH/SH-5-NU KH/SH-6-NU
3234557
Control Knob
X
X
X
X
X
X
X
X
X
X
*000-519-0001
Food Warmer, 208V, w/o Drain
X
X
X
X
X
X
X
X
X
X
*000-442-0031
Heated Door Assembly
X
X
X
X
*000-442-0030
Heated Door Assembly
X
6190215
Heating Element
X
X
X
X
X
2194110
Infinite Control 208V
X
X
X
X
X
X
X
X
X
X
2194212
On/Off Switch
X
X
X
X
X
X
X
X
X
X
2194095
Pilot Light
X
X
X
X
X
X
X
X
X
X
2194460
Thermostat (Heated Insert)
X
X
X
X
X
Refrigerated Cold Pans
Heated and Refrigerated Combo Counters
Part Number
Description
Part Number
Description
3234902
Caster, 5"
3234902
Caster, 5"
3234783
Caster, 5", with brake
3234783
Caster, 5", with brake
*000-BN5-0030
Condensing Unit, 1/4HP
*000-BN5-0030
Condensing Unit, 1/4HP
3234242
Drain
3234557
Control Knob
3516225
Expansion Valve
3234242
Drain
*356-411-0001
Louver Panel, End
3516225
Expansion Valve
*356-411-0000
Louver Panel, Front/Rear
*000-519-0001
Food Warmer, 208V, w/o Drain
2193927
Low Pressure Control
2194110
Infinite Control 208V
2190154
Rocker Switch
*356-411-0001
Louver Panel, End
*356-411-0000
Louver Panel, Front/Rear
2193927
Low Pressure Control
2194212
On/Off Switch
2194095
Pilot Light
2190154
Rocker Switch
Shelleyglas & Shelleysteel with LiquiTec
Part Number
Description
3234902
Caster, 5"
3234783
Caster, 5", with brake
*000-BN5-0030
Condensing Unit, 1/4HP
3516225
Expansion Valve
*356-411-0001
Louver Panel, End
*356-411-0000
Louver Panel, Front/Rear
2193927
Low Pressure Control
2190154
Rocker Switch
* Exploded views and replacement parts shown on page 17.
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
17
Shelleyglas®/Shelleysteel™ Service and Installation Manual
Replacement Parts List
Heated and Ice Cooled Combo Counters
Ice Cream Counters
Part Number
Description
Part Number
Description
*272-412-0000
Access Panel
*000-bn5-0030
Assy, 1/4 Hp Cond Unit
*265-102-0030
Bottom, Perforated
3234902
Caster, 5, Plt, Swvl,
3234902
Caster, 5"
3234783
Caster, 5, Plt, Swvl, Brk,
3234783
Caster, 5", with brake
3234242
Drain, Plastic, 1ips, 2.87
3234557
Control Knob
3234669
Interlock Assy, Sg,
3234242
Drain
3234188
Lid, Large, Ice Cream,
*000-519-0001
Food Warmer, 208V, w/o Drain
*356-411-0001
Panel, Shy Lvr, End
2194110
Infinite Control 208V
*356-411-0000
Panel, Shy Lvr, Frt/rear
2194212
On/Off Switch
6150201
Spring, Extension,
2194095
Pilot Light
2190154
Switch, Rocker, 20a/125v,
Frost Top Serving Counters
Milk And Ice Cream Counters
Part Number
Description
Part Number
Description
*000-bn5-0030
Assy, 1/4 Hp Cond Unit
*000-bn5-0030
Assy, 1/4 Hp Cond Unit
3234902
Caster, 5, Plt, Swvl,
3234902
Caster, 5, Plt, Swvl,
3234783
Caster, 5, Plt, Swvl, Brk,
3234783
Caster, 5, Plt, Swvl, Brk
3234242
Drain, Plastic, 1ips, 2.87
3234242
Drain, Plastic, 1ips, 2.87
3234669
Interlock Assy, Sg
3234669
Interlock Assy, Sg
*356-411-0001
Panel, Shy Lvr, End
3234188
Lid, Large, Ice Cream
*356-411-0000
Panel, Shy Lvr, Frt/rear
*356-411-0001
Panel, Shy Lvr, End
2190154
Switch, Rocker, 20a/125v,
*356-411-0000
Panel, Shy Lvr, Frt/rear
6150201
Spring, Extension,
2190154
Switch, Rocker, 20a/125v,
Milk Counters
Part Number
Description
3234902
Caster, 5, Plt, Swvl,
3234783
Caster, 5, Plt, Swvl, Brk,
3526674
Cond Unit, 1/4hp, Hi, R134a
3234242
Drain, Plastic, 1ips, 2.87
3516101
Drier, Filter, 1/4odf
3234669
Interlock Assy, Sg
3234188
Lid, Large, Ice Cream,
*356-411-0001
Panel, Shy Lvr, End
*356-411-0000
Panel, Shy Lvr, Frt/rear
6150201
Spring, Extension,
2190154
Switch, Rocker, 20a/125v,
* Exploded views and replacement parts shown on page 17.
18
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
Shelleyglas®/Shelleysteel™ Service and Installation Manual
Exploded Views & Replacement Parts
2
3
4
1
5
000-442-0030
Heated Door Assembly
1701249
Door Gasket
3234067
Flag Hinge
000-442-0031
Heated Door Assembly
1701244
Door Gasket
3234067
Flag Hinge
6
7
000-BN5-0030
1
2
3
4
000-519-0001
Food Warmer, 208V, w/o Drain
1 2194335
Hi-Limt Safety Switch
2 2194007
Heating Element 208V
3 026-061-0001
Deflector Plate
4 0160014
Hot Food Well, 12 x 20
Condensing Unit, 1/4HP
1 3516457
Fan Blade
2 2160020
Fan Guard
3 2162717
Fan Motor
4 3526999
Danfoss Compressor
5 3516444
Compressor Relay
5 2194787
Start Capacitor
6 3516322
Filter Drier
7 3516454
Condenser Coil
265-102-0030
Bottom, Perforated
272-412-0000
Access Panel
356-411-0000
Louver Panel, Front/Rear
356-411-0001
Louver Panel, End
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
19
Shelleyglas®/Shelleysteel™ Service and Installation Manual
Standard Labor Guidelines To Repair Or Replace Parts On Delfield Equipment
Advice and recommendations given by Delfield Service Technicians do not constitute or guarantee any special coverage.
•A maximum of 1-hour is allowed to diagnose a defective component.
•A maximum of 1-hour is allowed for retrieval of parts not in stock.
•A maximum travel distance of 100 miles round trip and 2-hours will be reimbursed.
•Overtime, installation/start-up, normal control adjustments, general maintenance, glass breakage, freight damage, and/or
correcting and end-user installation error will not be reimbursed under warranty unless pre-approved with a Service Work
Authorization from Delfield. You must submit the number with the service claim.
LABOR OF 1-HOUR IS ALLOWED TO REPLACE:
•Thermostat
•Infinite Switch
•Door Jamb Switch
•Solenoid Coil
•Hi-limit/Thermal Protector Switch
•Fan Delay/Defrost Termination Switch
•Compressor Start Components and Overload Protector
•Defrost Timer
•Thermometer
•Gear Box
•
•
•
•
•
•
•
•
•
Contactor/Relay
Transformer
Evaporator/Condenser Fan Motor and Blade
Circulating Fan Motor and Blade
Microprocessor Control
Water Level Sensor/Probe
Door Hinges, Locks, and Gaskets
Condensate Element
Springs/Lowerator
LABOR OF 2 HOURS TO REPLACE:
•Drawer Tracks/Cartridges
• Defrost Element
•Pressure Control
• Heating Element
•Solenoid Valve
• Locate/Repair Leak
LABOR OF 3 HOURS TO REPLACE:
•EPR or CPR Valve
• Condenser or Evaporator Coil
•Expansion Valve
LABOR OF 4 HOURS TO REPLACE
•Compressor
This includes recovery of refrigerant and leak check.
$55.00 maximum reimbursement for refrigerant recovery (includes recovery machine, pump, torch, oil, flux, minor fittings,
solder, brazing rod, nitrogen, or similar fees.)
REFRIGERANTS
•R22 A maximum of $4.00/lb. or 25¢/oz. will be reimbursed.
•R134A A maximum of $5.00/lb. or 31¢/oz. will be reimbursed.
•R404A A maximum of $15.00/lb. or $1.00/oz. will be reimbursed.
20
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
Shelleyglas®/Shelleysteel™ Service and Installation Manual
Standard One Year Limited Warranty One year parts, 90 days labor
The Delfield Company (“Delfield”) warrants to the Original Purchaser
of the Delfield product (herein called the “Unit”) that such Unit, and
all parts thereof, will be free from defects in material and workmanship
under normal use and service for a period of one (1) year from the date
of shipment of the Unit to the Original Purchaser or, if the Original
Purchaser returns the warranty card completely filled out including
the date of installation within thirty (30) days of receipt of the Unit,
one (1) year from the date of installation. During this one year
warranty period, Delfield will repair or replace any defective part or
portion there of returned to Delfield by the Original Purchaser which
Delfield determines was defective due to faulty material or workmanship.
The Original purchaser will pay all labor, crating, freight and related
costs incurred in the removal of the Unit of defective component and
shipment to Delfield, except that during a period of either ninety (90)
days from the date of shipment of the Unit to the Original Purchaser or,
if the Original Purchaser returns the warranty card completely filled out
including the date of installation within thirty (30) days of receipt of the
Unit, ninety (90) days from the date of installation Delfield will pay all
related labor costs. Delfield will pay the return costs if the Unit or part
thereof was defective.
The term “Original Purchaser” as used herein means that person, firm,
association, or corporation for whom the Unit was originally installed.
This warranty does not apply to any Unit or part thereof that has
been subjected to misuse, neglect, alteration, or accident, such as
accidental damage to the exterior finish, operated contrary to the
recommendations specified by Delfield; or repaired or altered by anyone
other than Delfield in any way so as to, in Delfield’s sole judgement,
affect its quality or efficiency. This warranty does not apply to any Unit
that has been moved from the location where it was originally installed.
This warranty also does not cover the refrigerator drier or the light
bulbs used in the Unit. The warranty is subject to the user’s normal
maintenance and care responsibility as set forth in the Service and
Installation Manual, such as cleaning the condenser coil, and is in
lieu of all other obligations of Delfield. Delfield neither assumes, nor
authorizes any other person to assume for Delfield, any other liability
in connection with Delfield’s products.
Removal or defacement of the original Serial Number or Model Number
from any Unit shall be deemed to release Delfield from all obligations
hereunder or any other obligations, express or implied.
Parts furnished by suppliers to Delfield are guaranteed by Delfield only
to the extent of the original manufacturer’s express warranty to Delfield.
Failure of the Original Purchaser to receive such manufacturers warranty
shall in no way create any warranty, expressed or implied, or any other
obligation or liability on Delfield’s part in respect thereof.
IF THE CUSTOMER IS USING A PART THAT RESULTS IN A VOIDED
WARRANTY AND A DELFIELD AUTHORIZED REPRESENTATIVE
TRAVELS TO THE INSTALLATION ADDRESS TO PERFORM WARRANTY
SERVICE, THE SERVICE REPRESENTATIVE WILL ADVISE CUSTOMER
THE WARRANTY IS VOID. SUCH SERVICE CALLS WILL BE BILLED
TO CUSTOMER AT THE AUTHORIZED SERVICE CENTER’S THEN
APPLICABLE TIME AND MATERIALS RATES. CONSIDER: CUSTOMER
MAY INITIATE A SERVICE AGREEMENT WITHOUT PARTS COVERAGE.
If shipment of a replacement part is requested prior to the arrival in the
Delfield factory of the part claimed to be defective, the Original Purchaser
must accept delivery of the replacement part on a C.O.D. basis, with
credit being issued after the part has been received and inspected at
Delfield’s plant and determined by Delfield to be within this warranty.
Under no condition does this warranty give the Original Purchaser the
right to replace the defective Unit with a complete Unit of the same
manufacturer or of another make. Unless authorized by Delfield in
writing, this warranty does not permit the replacement of any part,
including the motor-compressor, to be made with the part of another
make or manufacturer.
No claims can be made under this warranty for spoilage of any products
for any reason, including system failure.
The installation contractor shall be responsible for building access,
entrance and field conditions to insure sufficient clearance to allow any
hood(s), vent(s), or Unit(s) if necessary, to be brought into the building.
Delfield will not be responsible for structural changes or damages
incurred during installation of the Unit or any exhaust system.
Delfield shall not be liable in any manner for any default or delay in
performance hereunder caused by or resulting from any contingency
beyond Delfield’s control, including, but not limited to, war, governmental
restrictions or restraints, strike, lockouts, injunctions, fire, flood, acts of
nature, short or reduced supply of raw materials, or discontinuance of
the parts by the original part manufacturer.
Except as provided in any Additional Four Year Protection Plan, if
applicable, and the Service Labor Contract, if applicable, the foregoing
is exclusive and in lieu of all other warranties, whether written or
oral, express or implied. This warranty supersedes and excludes
any prior oral or written representations or warranties. Delfield
expressly disclaims any implied warranties of merchantability,
fitness for a particular purpose, or compliance with any law, treaty,
rule or regulation relating to the discharge of substances into
the environment. The sole and exclusive remedies of any person
relating to the Unit, and the full liability of Delfield for any breach of
this warranty, will be as provided in this warranty.
Other than this Delfield Standard One Year Limited Warranty, any
applicable Delfield Additional Four Year Protection Plan or applicable
Delfield Service Labor Contract, the Original Purchaser agrees and
acknowledges that no other warranties are offered or provided in
connection with or for the Unit or any other part thereof.
In no event will Delfield be liable for special, incidental or consequential
damages, or for damages in the nature of penalties.
IF DURING THE WARRANTY PERIOD, CUSTOMER USES A PART FOR
THIS DELFIELD EQUIPMENT OTHER THAN AN UNMODIFIED NEW OR
RECYCLED PART PURCHASED DIRECTLY FROM DELFIELD OR ANY OF
ITS AUTHORIZED SERVICE CENTERS AND/OR THE PART BEING USED
IS MODIFIED FROM ITS ORIGINAL CONFIGURATION, THIS WARRANTY
WILL BE VOID. FURTHER, DELFIELD AND ITS AFFILIATES WILL NOT
BE LIABLE FOR ANY CLAIMS DAMAGES OR EXPENSES INCURRED
BY THE CUSTOMER WHICH ARISE DIRECTLY OR INDIRECTLY, IN
WHOLE OR IN PART, DUE TO THE INSTALLATION OF ANY MODIFIED
PART AND/OR PART RECEIVED FROM AN UNAUTHORIZED SERVICE
CENTER. If the warranty becomes void, Customer may purchase from
Delfield, if available, a Service Agreement or service at the then
current time and materials rate.
For more information on Delfield warranty’s log on and check out the
service section of our web site at www.delfield.com.
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
21
Shelleyglas®/Shelleysteel™ Service and Installation Manual
Additional Four Year Protection Plan
Delfield Model#
Serial #
for Motor-Compressor only
Installation
Date
In addition to the Standard One Year Warranty on the MotorCompressor contained in the above listed Delfield product (the
“Unit”), The Delfield Company (“Delfield”) also agrees to repair, or
exchange with similar or interchangeable parts in design and capacity
at Delfield’s option, the defective Motor-Compressor contained in the
Unit (the “Motor-Compressor), or any part thereof, for the Original
Purchaser only, at any time during the four (4) years following the
initial one (1) year period commencing on the date of installation for the
Original Purchaser. Failure of the Original Purchaser to register the
registration card containing the Original Purchasers name, address,
date of installation, model number and serial number of the Unit
containing the Motor-Compressor within 30 days from the date of
installation shall void this warranty. This additional warranty is only
available if the Motor-Compressor is inoperative due to defects in
material or factory workmanship, as determined by Delfield in its sole
judgement and discretion. The Original Purchaser shall be responsible
for returning the defective Motor-Compressor to Delfield prepaid, F.O.B.
at the address shown on the back cover of this manual.
The term “Original Purchaser” as used herein means that person, firm,
association, or corporation for whom the Unit was originally installed.
The term “Motor-Compressor” as used herein does not include unit
base, air or water cooled condenser, receiver, electrical accessories
such as relay, capacitors, refrigerant controls, or condenser fan/motor
assembly. This warranty does not cover labor charges incidental to
the replacement of parts. This warranty further does not include
any equipment to which said condensing unit is connected, such as
cooling coils, temperature controls or refrigerant metering devices.
This warranty shall be void if the Motor-Compressor, in Delfield’s
sole judgement, has been subjected to misuse, neglect, alteration or
accident, operated contrary to the recommendations specified by the
Unit manufacturer, repaired or altered by anyone other than Delfield
in any way so as, in Delfield’s sole judgment, to affect its quality or
efficiency or if the serial number has been altered, defaced or removed.
This Warranty does not apply to a Motor-Compressor in any Unit that
has been moved from the location where it was originally installed.
The addition of methyl chloride to the condensing unit or refrigeration
system shall void this warranty.
22
General Conditions
Delfield shall not be liable in any manner for any default or delay in
performance hereunder caused by or resulting from any contingency
beyond Delfield’s control, including, but not limited to, war,
governmental restrictions or restraints, strike, lockouts, injunctions,
fire, flood, acts of nature, short or reduced supply of raw materials,
or discontinuance of any part or the Motor-Compressor by the unit
manufacturer.
Replacement of a defective Motor-Compressor is limited to one (1)
Motor-Compressor by us during the four (4) year period. Delfield
shall replace the Motor-Compressor at no charge.
This warranty does not give the Original Purchaser of the MotorCompressor the right to purchase a complete replacement MotorCompressor of the same make or of another make. It further does
not permit the replacement to be made with a Motor-Compressor
of another kind unless authorized by Delfield. In the event Delfield
authorizes the Original Purchaser to purchase a replacement MotorCompressor locally, only the wholesale cost of the Motor-Compressor
is refundable.
Expressly excluded from this warranty are damages resulting from
spoilage of goods.
Except as provided in any applicable Standard One Year Limited
Warranty or applicable Service Labor Contract, the foregoing is
exclusive and in lieu of all other warranties, whether written or
oral, express or implied. This Warranty supersedes and excludes
any prior oral or written representations or warranties. Delfield
expressly disclaims any implied warranties of merchantability,
fitness for a particular purpose or compliance with any law, treaty,
rule or regulation relating to the Motor-Compressor, and the full
liability of Delfield for any breach of this warranty, will be as
provided in this warranty.
Other than any applicable Delfield Standard One year Limited
Warranty, this Delfield Additional Four Year Protection Plan and any
applicable Delfield Service Labor Contract, the Original Purchaser
agrees and acknowledges that no other warranties are offered or
provided in connection with or for the Motor-Compressor or any
part thereof.
In no event will Delfield be liable for special, incidental or consequential
damages, or for damages in the nature of penalties.
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
Shelleyglas®/Shelleysteel™ Service and Installation Manual
Notes
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
23
Covington, TN
Mt. Pleasant, MI
Thank you for choosing Delfield!
Help is a phone call away. Help our team of professional, courteous
customer service reps by having your model number and serial number
available at the time of your call (800) 733-8829
Model:_______________ S/N: ________________________
Installation Date:_____________
For a list of Delfield’s authorized parts depots,
visit our website at www.delfield.com
980 S. Isabella Rd., Mt. Pleasant, MI 48858, U.S.A. • (989) 773-7981 or (800) 733-8829 • Fax (989) 773-3210 • www.delfield.com
Delfield reserves the right to make changes in design or specifications without prior notice. ©2010 The Delfield Company. All rights reserved. Printed in the U.S.A.
DMSG_SS 09/10
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement