Specifications | Braun 590CC Electric Shaver User Manual

Series 5
se
ns
iti
ve
590 cc
570 cc
on • off
min
Type 5751
www.braun.com/register
98805740_590cc_Korea.indd 13
24.09.2008 13:22:30 Uhr
counter. While doing so, the replacement
light blinks and goes off when the reset is
complete. The manual reset can be done at
any time.
Accessories
Available at your dealer or Braun Service
Centres:
• Shaver foil and cutter block: 51S
• Cleaning cartridge Clean&Renew: CCR
Environmental notice
This product contains rechargeable
batteries. In the interest of protecting
the environment, please do not
dispose of the product in the household waste at the end of its useful life.
Disposal can take place at a Braun Service
Centre or at appropriate collection points
provided in your country.
The cleaning cartridge can be disposed with
regular household waste.
Guarantee
We grant 1 year guarantee on the product
commencing on the date of purchase. Within
the guarantee period we will eliminate, free of
charge, any defects in the appliance resulting
from faults in materials or workmanship,
either by repairing or replacing the complete
appliance as we may choose.
This guarantee extends to every country
where this appliance is supplied by Braun or
its appointed distributor.
This guarantee does not cover: damage due
to improper use, normal wear and tear (e.g.
shaver foil or cutter block) as well as defects
that have a negligible effect on the value or
operation of the appliance. The guarantee
becomes void if repairs are undertaken by
unauthorised persons and if original Braun
parts are not used.
To obtain service within the guarantee period,
hand in or send the complete appliance with
your sales receipt to an authorised Braun
Customer Service Centre.
Subject to change without notice.
This product conforms to the European
Directives EMC 2004/108/EC and Low
Voltage 2006/95/EC.
For electric specifications, see printing on the
special cord set.
Braun GmbH
Frankfurter Straße 145
61476 Kronberg/Germany
98805740/IX-08
Korea/GB
12
98805740_590cc_Korea.indd 12
24.09.2008 13:22:29 Uhr
3
4
5
7
aning
s t a r t c le
8
9
2
washable
1
10
se
ns
iti
ve
11
12
min
on • off
13
14
6
15
16
17
18
590
570
STOP
19
20
STOP
on •
off
sens
i
sens tive
itive
2
98805740_590cc_Korea.indd 2
24.09.2008 13:22:23 Uhr
A
aning
s t a r t c le
aning
start cle
aning
start cle
1
2
min
min
min
new
clean
s t a r t c le a nin g
on • off
min
s
aning
s t a r t c le
B
1
2
3
se
n
si
tiv
1 2 3
e
e
on • off
full
ive
sit
wa
sh
a
ble
se
n
low
itive
ns
se
90°
3
98805740_590cc_Korea.indd 3
24.09.2008 13:22:24 Uhr
C
a
clean
aning
s t a r t c le
aning
start cle
•••
min
b
new
min
•••
full
min
min
on • off
s
c
aning
s t a r t c le
min
old
an
clenn
clcleaea
www
lololo
D
full
full
on
•o
ff
on
sensitive
•o
ff
sensitive
an
clenn
clcleaea
www
lololo
full
on
•o
ff
se
n
sit
ive
sensitive
n
se
ive
sit
on • off
on •
off
4
98805740_590cc_Korea.indd 4
24.09.2008 13:22:24 Uhr
5
98805740_590cc_Korea.indd 5
24.09.2008 13:22:24 Uhr
6
98805740_590cc_Korea.indd 6
24.09.2008 13:22:25 Uhr
7
98805740_590cc_Korea.indd 7
24.09.2008 13:22:26 Uhr
8
98805740_590cc_Korea.indd 8
24.09.2008 13:22:27 Uhr
English
Our products are designed to meet the
highest standards of quality, functionality and
design. We hope you enjoy your new Braun
Shaver.
Warning
Your shaving system is provided with a
special cord set, which has an integrated
Safety Extra Low Voltage power supply. Do
not exchange or tamper with any part of it,
otherwise there is risk of an electric shock.
To prevent the cleaning fluid from leaking,
ensure that the Clean&Renew station is
placed on a flat surface. When a cleaning
cartridge is installed, do not tip, move
suddenly or transport the station in any
way as cleaning fluid might spill out of the
cartridge. Do not place the station inside a
mirror cabinet, nor place it on a polished or
lacquered surface.
The cleaning cartridge contains a highly
flammable liquid so keep it away from
sources of ignition. Do not expose to direct
sunlight and cigarette smoking nor store it
over a radiator.
Keep it out of reach of children.
Do not refill the cartridge and use only
original Braun refill cartridges.
Description
Clean&Renew™ station
1 Level indicator
2 Lift button for cartridge exchange
3 Station-to-shaver contacts
4 Start button
5 Station power socket
6 Cleaning cartridge
Shaver
7 Shaver foil
8 Cutter block
9 Foil release buttons
10 Long hair trimmer
11
12
13
14
15
16
17
18
19
20
Comfort setting switch «sensitive»
Shaver-to-station contacts
On/off switch
Shaver display
Cleaning light (yellow)
Replacement light for shaving parts
Reset button
Shaver power socket
Special cord set
Etui
A Before shaving
Prior to first use, you have to connect the
shaver to an electrical outlet using the special
cord set (19) or alternatively, proceed as
follows:
Installing the Clean&Renew station
• Using the special cord set (19), connect the
station power socket (5) to an electrical
outlet.
• Press the lift button (2) to open the housing
• Hold the cleaning cartridge (6) down on a
flat, stable surface (e.g. table).
• Carefully remove the lid from the cartridge.
• Slide the cartridge into the base of the
station as far as it will go.
• Slowly close the housing by pushing it
down until it locks.
Charging the shaver in the Clean&Renew
station
Insert the shaver head down into the cleaning
station. (The contacts (12) on the back of the
shaver will align with the contacts (3) in the
cleaning station).
If required, the Clean&Renew station will start
charging the shaver now.
A full charge provides up to 45 minutes of
cordless shaving time. This may vary
according to your beard growth.
The best environmental temperature for
charging is between 5 °C to 35 °C. Do not
expose the shaver to temperatures higher
than 50 °C for extended periods of time.
9
98805740_590cc_Korea.indd 9
24.09.2008 13:22:27 Uhr
Shaver display
The shaver display (14) shows the charge
status of the battery. During charging or
when using the shaver, the respective green
battery segment will blink. When fully
charged, all green segments will light up for
approximately one hour, provided the shaver
sits in the C&R station.
Tips for the perfect shave
For best results, Braun recommends you
follow 3 simple steps:
1. Always shave before washing your face.
2. At all times, hold the shaver at right
angles (90°) to your skin.
3. Stretch your skin and shave against the
direction of your beard growth.
The red low charge segment flashes when
the battery capacity has dropped below
20 %, provided the shaver is switched on.
The remaining capacity will then be sufficient
for 2 to 3 shaves.
Shaving with the cord
If the shaver has run out of power
(discharged), you may also shave with the
shaver connected to an electrical outlet via
the special cord set.
B Shaving
Cleaning
Press the on/off switch (13) to operate the
shaver.
For best shaving results, we recommend
cleaning the shaver in the station after each
shave (see «Automatic cleaning»).
All charging and cleaning needs are then
automatically taken care of.
Comfort setting switch «sensitive»
Setting the shaver head according to your
comfort needs.
The «sensitive» switch (11) provides three
options for comfort setting:
1 «+»:
The shaver head is in full swing, freely
follows the contours of your skin to
provide more comfort.
Cleaning indicator
Clean your shaver in the Clean&Renew
station at the latest when the yellow cleaning
light (15) shines constantly after shaving.
If this is not done, the cleaning light will go
off after some time and the counter will be
reset.
2 middle position:
The shaver head is semi-fixed for more
control.
3 «–»:
The shaver head is fixed for full control
and precise handling in hard to reach
areas.
Long hair trimmer
To trim sideburns, moustache or beard, slide
the long hair trimmer (10) upwards.
C Automatic cleaning
The Clean&Renew has been developed for
cleaning, charging and storing your shaver.
After each shave, return the shaver to the
Clean&Renew station and proceed as
follows:
• Insert the shaver head down into the
cleaning station.
• Push down the start button (4). The cleaning process will start (approx. 5 minutes
cleaning, 4 hours drying).
• Do not interrupt the cleaning process, as
it leaves the shaver wet and not fit for use.
10
98805740_590cc_Korea.indd 10
24.09.2008 13:22:28 Uhr
•
•
•
•
If interruption is needed nonetheless, press
the start button (4).
When cleaning is finished, the yellow
cleaning light will go off and the shaver is
ready for use.
A cleaning cartridge should be sufficient for
about 30 cleaning cycles. When the level
indicator (1) has reached the «min» mark,
the remaining fluid in the cartridge is
sufficient for about 5 more cycles. Then the
cartridge should be replaced, when used
daily approx. every 4 weeks.
The hygienic cleaning cartridge contains
alcohol, which once opened will naturally
evaporate slowly into the surrounding air.
Each cartridge, if not daily used, should be
replaced after approximately 8 weeks.
The cleaning cartridge also contains
lubricates, which may leave residual marks
on the shaver head after cleaning.
However, these marks can be removed
easily by wiping gently with a cloth or soft
tissue paper.
Cleaning the housing
From time to time clean the housing of the
shaver and the Clean&Renew station with a
damp cloth, especially inside the cleaning
chamber where the shaver rests.
Replacing the cleaning cartridge
After having pressed the lift button (2) to
open the housing, wait for a few seconds
before removing the used cartridge to avoid
any dripping.
Before discarding the used cartridge, make
sure to close the openings using the lid of the
new cartridge, since the used cartridge will
contain contaminated cleaning solution.
D Manual cleaning
The shaver head is suitable for
cleaning under running tap water.
Warning: Detach the shaver from the
power supply before cleaning the
shaver head in water.
Rinsing the shaver head under running water
is an alternative way to keep the shaver
clean, especially when traveling:
• Switch the shaver on (cordless) and rinse
the shaver head under hot running water.
You may use liquid soap without abrasive
substances. Rinse off all foam and let the
shaver run for a few more seconds.
• Next, switch off the shaver, press the foil
release buttons (9) to remove the shaver
foil (7) and cutter block (8). Then leave the
disassembled shaving parts to dry.
• If you regularly clean the shaver under
water, then once a week apply a drop of
light machine oil onto the long hair trimmer
and shaver foil.
The following quick cleaning is another
alternative cleaning method:
• Press the foil release buttons (9) to lift
the shaver foil (do not remove the foil
completely). Switch on the shaver for
approx. 5–10 seconds so that the shaved
stubbles can fall out.
• Switch off the shaver. Remove the shaver
foil and tap it out on a flat surface. Using
the brush, clean the inner area of the
shaver head. However, do not clean the
shaver foil nor the cutter block with the
brush as this will damage them.
Keeping your shaver in top
shape
Replacing the foil and cutter block/reset
To maintain 100% shaving performance,
replace the shaver foil (7) and cutter block (8),
when the replacement symbol (16) lights up
(after about 18 months) or when cassette is
worn.
The replacement symbol will remind you
during the next 7 shaves to replace the
shaver foil and cutter block. Then the shaver
will automatically reset the display. After you
have replaced the shaver foil and cutter
block, use a ball-pen to push the reset button
(17) for at least 3 seconds to reset the
11
98805740_590cc_Korea.indd 11
24.09.2008 13:22:28 Uhr
Download PDF

advertising