Breville BTA820XL Toaster User Manual

Operating & Maintenance
Instructions
Model Series
Covered in
This Manual
110000
120000
200000
210000
Model
Type
Note: General Model Series numbers noted above are inclusive of the specific model
number found on your engine. To get replacement parts or technical assistance in
the future, write your engine Model, Type, Code and date of purchase here.
TABLE OF CONTENTS
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
Engine Information . . . . . . . . . . . . . . . . . . . . . . . . 6
Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Fuel and Starting Information . . . . . . . . . . . . . . . 8
Starting and Stopping . . . . . . . . . . . . . . . . . . . 9-10
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . 11-14
Parts and Service & Storage . . . . . . . . . . . . 15-16
Warranty Information . . . . . . . . . . . . . . . . . . . . . 17
PRINTED IN U.S.A.
Document: - page 1 (Black)
Screen angle and frequency: 45.0000, 150.0000
Code
Month Day Year
WARNING
Briggs & Stratton does not approve or authorize the use of
these engines on 3-wheel All Terrain Vehicles (ATVs), motor
bikes, fun/recreational go-karts, aircraft products or vehicles
intended for use in competitive events. Use of these engines in
such applications could result in property damage, serious
injury (including paralysis), or even death.
Need assistance? Go to www.briggsandstratton.com
for detailed information regarding Briggs & Stratton engines.
Or call, 1-800-233-3723, (U.S.A. and Canada)
to hear a menu of pre-recorded messages
offering engine maintenance information.
© Copyright 2005 by Briggs & Stratton Corporation
FORM NO. 275092-8/05
2
Document: - page 2 (Black)
Screen angle and frequency: 45.0000, 150.0000
275092
BEFORE OPERATING ENGINE
• Read entire Operating & Maintenance Instructions AND
the instructions for the equipment this engine powers.*
• Failure to follow instructions could result in serious injury
or death.
THE OPERATING & MAINTENANCE INSTRUCTIONS
CONTAIN SAFETY INFORMATION TO
• Make you aware of hazards associated with engines
• Inform you of the risk of injury associated with those hazards, and
• Tell you how to avoid or reduce the risk of injury.
(
)
HAZARD SYMBOLS AND MEANINGS
The safety alert symbol
is used to identify safety
information about hazards that can result in personal injury.
A signal word (DANGER, WARNING, or CAUTION) is
used with the alert symbol to indicate the likelihood and the
potential severity of injury. In addition, a hazard symbol
may be used to represent the type of hazard.
Fire
Explosion
Moving Parts
DANGER indicates a hazard which, if not
avoided, will result in death or serious injury.
Toxic Fumes
Hot Surface
Shock
WARNING indicates a hazard which, if not
avoided, could result in death or serious injury.
Kickback
CAUTION indicates a hazard which, if not
avoided, might result in minor or moderate
injury.
THE INTERNATIONAL SYMBOLS USED
ON THE ENGINE OR
IN THIS MANUAL INCLUDE:
CAUTION, when used without the alert symbol,
indicates a situation that could result in damage
to the engine.
WARNING
Safety Alert
The engine exhaust from this product contains chemicals known to the
State of California to cause cancer,
birth defects, or other reproductive
harm.
*
Oil
Read Owner’s
Manual
Stop Fuel Shutoff Choke
On Off
Fuel
Briggs & Stratton does not necessarily know what equipment this engine will power. For that reason, you should carefully read
and understand the operating instructions for the equipment on which your engine is placed.
3
Document: - page 3 (Black)
Screen angle and frequency: 45.0000, 150.0000
SAFETY
WARNING
WARNING
Starting engine creates sparking.
Gasoline and its vapors are extremely
flammable and explosive.
Sparking can ignite nearby flammable
gases.
Fire or explosion can cause severe burns
or death.
Explosion and fire could result.
WHEN ADDING FUEL
• If there is natural or LP gas leakage in area, do not
start engine.
• Do not use pressurized starting fluids because
vapors are flammable.
• Turn engine OFF and let engine cool at least 2
minutes before removing gas cap.
• Fill fuel tank outdoors or in well-ventilated area.
• Do not overfill fuel tank. Fill tank to approximately
1-1/2 inches below top of neck to allow for fuel
expansion.
• Keep gasoline away from sparks, open flames,
pilot lights, heat, and other ignition sources.
• Check fuel lines, tank, cap, and fittings frequently
for cracks or leaks. Replace if necessary.
WARNING
Rapid retraction of starter cord (kickback) will
pull hand and arm toward engine faster than
you can let go.
WHEN STARTING ENGINE
• Make sure spark plug, muffler, fuel cap and air
cleaner are in place.
• Do not crank engine with spark plug removed.
• If fuel spills, wait until it evaporates before starting
engine.
• If engine floods, set choke to OPEN/RUN position,
place throttle in FAST and crank until engine starts.
Broken bones, fractures, bruises or sprains
could result.
• When starting engine, pull cord slowly until
resistance is felt, then pull rapidly.
• Remove all external equipment/engine loads
before starting engine.
• Direct coupled equipment components such as,
but not limited to, blades, impellors, pulleys,
sprockets, etc., must be securely attached.
WHEN OPERATING EQUIPMENT
• Do not tip engine or equipment at angle which
causes gasoline to spill.
• Do not choke carburetor to stop engine.
WHEN TRANSPORTING EQUIPMENT
WARNING
• Transport with fuel tank EMPTY or with fuel shut-off
valve OFF.
Rotating parts can contact or entangle
hands, feet, hair, clothing, or accessories.
WHEN STORING GASOLINE OR EQUIPMENT
WITH FUEL IN TANK
Traumatic amputation or severe laceration
can result.
• Store away from furnaces, stoves, water heaters or
other appliances that have pilot light or other
ignition source because they can ignite gasoline
vapors.
• Operate equipment with guards in place.
• Keep hands and feet away from rotating parts.
• Tie up long hair and remove jewelry.
• Do not wear loose-fitting clothing, dangling
drawstrings or items that could become caught.
4
Document: - page 4 (Black)
Screen angle and frequency: 45.0000, 150.0000
SAFETY
WARNING
WARNING
Engines give off carbon monoxide, an
odorless, colorless, poison gas.
Breathing carbon monoxide can cause
nausea, fainting or death.
• Start and run engine outdoors.
• Do not start or run engine in enclosed area, even if
doors or windows are open.
WARNING
Running engines produce heat. Engine
parts, especially muffler, become extremely
hot.
Severe thermal burns can occur on contact.
Combustible debris, such as leaves, grass,
brush, etc. can catch fire.
• Allow muffler, engine cylinder and fins to cool
before touching.
• Remove accumulated combustibles from muffler
area and cylinder area.
• Install and maintain in working order a spark
arrester before using equipment on forest-covered,
grass-covered, brush-covered unimproved land.
The state of California requires this (Section 4442
of the California Public Resources Code). Other
states may have similar laws. Federal laws apply
on federal land.
5
Document: - page 5 (Black)
Screen angle and frequency: 45.0000, 150.0000
ENGINE INFORMATION
9
1
10
2
11
16
3
1.
2.
3.
4.
5.
6.
7.
8.
9.
Spark plug
4
Air cleaner
Choke
Carburetor
5
Fuel shut-off valve
(if equipped)
Rope handle
Finger guard
Stop switch/OIL GARD® light
(if equipped)
Fuel fill
12
8
6
7
10. Fuel tank
11. Oil fill/Dipstick
(if equipped)
12. Blower housing 13
13. Oil drain plug
14. Oil fill cap
Model
Type
Code
15. Engine
xxxxx
xxxx xx
xxxxxxxx
16. Muffler/(Muffler guard, if equipped)/
(Spark arrester, if equipped)
15
14
GENERAL INFORMATION
MODEL SERIES 200000
ENGINE MODEL
Bore . . . . . . . . . . . . . . . . . . . . . . . . . . 3.120 in. (79.23 mm)
This is a single cylinder, overhead valve (OHV), air-cooled
engine. It is a low emissions engine.
Stroke . . . . . . . . . . . . . . . . . . . . . . . . 2.438 in. (61.67 mm)
In the state of California, OHV Model Series 110000 and
120000 engines are certified by the California Air Resources Board to meet emissions standards for 125 hours.
OHV Model Series 200000, 210000 engines are certified
by the California Air Resources Board to meet emissions
standards for 250 hours. Such certification does not grant
the purchaser, owner or operator of this engine any
additional warranties with respect to the performance or
operational life of this engine. This engine is warranted
solely according to the product and emissions warranties
stated elsewhere in this manual.
MODEL SERIES 210000
Displacement . . . . . . . . . . . . . . . . . . 18.64 cu. in. (305 cc)
Bore . . . . . . . . . . . . . . . . . . . . . . . . . . 3.300 in. (83.81 mm)
Stroke . . . . . . . . . . . . . . . . . . . . . . . . 2.438 in. (61.67 mm)
Displacement . . . . . . . . . . . . . . . . . . 20.85 cu. in. (342 cc)
TUNE-UP SPECIFICATIONS
Models 110000/120000
Armature air gap . . . 0.010 – 0.014 in. (0.25 – 0.36 mm)
Spark plug gap . . . . . . . . . . . . . . . . . . 0.030 in. (0.76 mm)
Valve clearance with valve springs installed and piston 1/4 in.
(6 mm) past top dead center (check when engine is cold).
See Repair Manual P/N 272147.
Intake . . . . . . . . . . . . . 0.004 – 0.006 in. (0.10 – 0.15 mm)
Exhaust . . . . . . . . . . . 0.009 – 0.011 in. (0.23 – 0.28 mm)
Note: For practical operation, horsepower loading should
not exceed 85% of rated horsepower. Engine power will decrease 3-1/2% for each 1,000 feet (300 meters) above sea
level and 1% for each 10° F (5.6° C) above 77° F (25° C).
Engine will operate satisfactorily at an angle up to 15°.
MODEL SERIES 110000
TUNE-UP SPECIFICATIONS
Models 200000/210000
Armature air gap . . . 0.008 – 0.012 in. (0.20 – 0.30 mm)
Spark plug gap . . . . . . . . . . . . . . . . . . 0.030 in. (0.76 mm)
Valve clearance with valve springs installed and piston 1/4 in.
(6 mm) past top dead center (check when engine is cold).
See Repair Manual P/N 272147.
Intake . . . . . . . . . . . . . 0.004 – 0.006 in. (0.10 – 0.15 mm)
Exhaust . . . . . . . . . . . 0.004 – 0.006 in. (0.10 – 0.15 mm)
Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11/16 in. (68 mm)
Stroke . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3/64 in. (52 mm)
Displacement . . . . . . . . . . . . . . . . . . 11.58 cu. in. (190 cc)
MODEL SERIES 120000
Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11/16 in. (68 mm)
Stroke . . . . . . . . . . . . . . . . . . . . . . . . . 2-13/64 in. (56 mm)
Displacement . . . . . . . . . . . . . . . . . . 12.48 cu. in. (206 cc)
6
Document: - page 6 (Black)
Screen angle and frequency: 45.0000, 150.0000
275092
OIL
Note: Synthetic oil meeting ILSAC GF-2, API
certification mark and API service symbol
(shown at left) with “SJ/CF ENERGY CONSERVING” or higher, is an acceptable oil at all
temperatures. Use of synthetic oil does not
alter required oil change intervals.
CAUTION: This engine is shipped from Briggs &
Stratton without oil. Check oil level before starting
engine. If you start the engine without oil, the
engine will be damaged beyond repair and will not
be covered under warranty.
Note: If this engine is equipped with gear reduction, gear
reduction case must be filled with oil prior to operating engine. See gear reduction oil filling instructions on page 12.
SAE Viscosity Grades
**
OIL CAPACITY
*
Model 110000 and 120000 series engines hold approximately 5/8 quart (20 ounces; 0.6 liter).
°F -20
°C -30
Model series 200000 and 210000 engines hold approximately 7/8 quart (28 ounces; 0.8 liter).
0
-20
20
-10
32
40
0
60
10
80
20
100
30
40
STARTING TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE
*
CAUTION: Air cooled engines run hotter than automotive
engines. The use of non-synthetic multi-viscosity oils
(5W-30, 10W-30, etc.) in temperatures above 40° F (4° C)
will result in higher than normal oil consumption. When using
a multi-viscosity oil, check oil level more frequently.
** CAUTION: SAE 30 oil, if used below 40° F (4° C), will result
in hard starting and possible engine bore damage due to
inadequate lubrication.
TYPE OF OIL TO USE
• Use a high quality detergent oil classified “For Service
SF, SG, SH, SJ” or higher, such as Briggs & Stratton
SAE 30, Part Number 100005 (20 oz) or 100028 (48 oz).
• Do not use special additives.
• Choose a viscosity according to the table opposite.
CHECKING AND ADDING OIL
• Check oil level before starting the engine.
• Check level daily, or after every eight (8) hours.
• Keep oil level at FULL.
• Do not overfill.
FULL
High
Oil Fill
(if equipped)
[2]
[1]
Place engine level and
clean around oil fill area.
Remove dipstick and wipe with clean
cloth. Replace and tighten dipstick.
Remove and check oil level.
[3]
[4]
Pour oil slowly. Fill to FULL line on
dipstick – recheck.
Replace and tighten dipstick.
Low
Oil Fill
OIL LEVEL
[1]
Place engine level and
clean around oil fill area.
[2]
Remove oil fill
cap or dipstick.
[3]
7
Document: - page 7 (Black)
Screen angle and frequency: 45.0000, 150.0000
Pour oil slowly. Fill to
point of overflowing.
[4]
Replace and tighten
oil fill cap.
OIL
CHECKING AND ADDING OIL
Low
Oil Fill
with Dipstick
[1]
Remove dipstick
and wipe with
clean cloth.
[2]
FULL OIL
LEVEL
Insert
dipstick,
but DO NOT
TIGHTEN.
Remove
and
check oil level.
[3]
Pour oil slowly.
Fill to FULL
mark on dipstick. Replace
and tighten dipstick.
FUEL
• This engine is certified to operate on gasoline. Exhaust
Emission Control System: EM (Engine Modifications).
TYPE OF FUEL TO USE
• Use clean, fresh, regular unleaded gasoline with a
minimum of 85 octane. Fresh fuel prevents gum from
forming in the fuel system or on essential carburetor parts.
Purchase fuel in quantity that can be used within 30 days.
• Do not use gasoline which contains Methanol.
• Do not mix oil with gasoline.
• For engine protection use Briggs & Stratton Gasoline
Additive available from your Authorized Briggs &
Stratton Dealer (P/N 5041 or single use pouch).
CAUTION: Some fuels, called oxygenated or reformulated gasoline, are gasoline blended with alcohols or
ethers. Excessive amounts of these blends can damage
the fuel system or cause performance problems. If any
undesirable operating symptoms occur, use gasoline
with a lower percentage of alcohol or ether.
ADDING FUEL
WARNING
Fuel Fill
• Turn engine OFF and let engine cool at least 2
minutes before removing gas cap.
• Fill fuel tank outdoors or in well-ventilated area.
• Keep gasoline away from sparks, open flames,
pilot lights, heat, and other ignition sources.
• If fuel spills, wait until it evaporates before
starting engine.
[1]
Remove cap. Fill tank to approximately 1-1/2
inches below top of neck to allow for fuel
expansion. Be careful not to overfill.
Briggs & Stratton Smart-fill) fuel can fills to the
correct level and automatically shuts off, reducing spills and emissions.
[2]
Replace cap before starting.
STARTING
STARTING AND OPERATING TIPS
♦ Store and fuel equipment in level position.
♦ Periodically remove any debris buildup from the
machine (See Maintenance.)
♦ After engine has started, let it warm up several
seconds to several minutes, depending on outside
temperature.
♦ For maximum performance and life, operate engine
with choke in RUN and throttle in FAST.
♦ Use fresh fuel. (See Fuel.)
♦ Use correct type of oil for expected starting
temperature. (See Oil.)
♦ Remove external equipment/engine loads. (See
equipment operating instructions.)
8
Document: - page 8 (Black)
Screen angle and frequency: 45.0000, 150.0000
STARTING AND STOPPING
WARNING
CAUTION: Some engines may be equipped with OIL
GARD®. The OIL GARD® is intended to warn the
operator that the engine is low on oil. Always check oil
level before starting. Engine damage may occur if the oil
level is not properly maintained and will void warranty
coverage. If the engine will not start, has stopped running
and/or a light flickers in the stop switch, add oil (see
instructions).
• Do not use pressurized starting fluids.
• Vapors are flammable.
REWIND (MANUAL) STARTER
TO START ENGINE
OIL
LEVEL
OPEN
POSITION
Fuel shut-off
FULL
[1]
Check oil level (see p. 7).
Choke
[2]
Turn fuel shut-off valve (if equipped) 1/4 turn
to OPEN.
[3]
Push choke lever to CHOKE position.
WARNING
[5]
Push rocker switch
(if equipped) to ON.
[6]
[4]
Move throttle (if
equipped) to FAST.
Operate engine with
throttle in FAST.
[7]
Let engine warm up.
If choke equipped:
Slowly adjust toward RUN
position. Wait until engine
runs smoothly before
each choke adjustment.
Grasp rope handle. Pull slowly until
resistance is felt, then pull rapidly to start
engine and avoid kickback.
TO STOP ENGINE
CAUTION: Do not stop
engine by moving choke
control to CHOKE.
Backfire, fire or engine
damage could occur.
[1]
Move throttle (if equipped)
to SLOW, then to STOP.
9
Document: - page 9 (Black)
Screen angle and frequency: 45.0000, 150.0000
[2]
Push rocker switch
(if equipped) to
OFF.
Fuel shut-off
[3]
Close fuel shut-off
valve (if equipped).
STARTING AND STOPPING
ELECTRIC (KEY) STARTER (if equipped)
TO START ENGINE
OIL
LEVEL
OPEN
POSITION
Fuel shut-off
FULL
[1]
Check oil level (see p. 7).
Choke
[2]
Turn fuel shut-off valve (if equipped) 1/4 turn
to OPEN.
[3]
Push choke lever to CHOKE position.
[7]
[5]
Push rocker switch (if
equipped) to ON.
[6]
[4]
Move throttle
(if equipped) to FAST.
Operate engine with
throttle in FAST.
Let engine warm up.
If choke equipped: Slowly adjust toward RUN
position. Wait until engine runs smoothly before
each choke adjustment.
CAUTION: To prolong starter life, use short starting
cycles (5 seconds maximum, then wait one minute).
Follow equipment manufacturer’s recommendations
for charging battery.
Insert key and
turn to START.
TO STOP ENGINE
[1]
Move throttle
(if equipped) to SLOW.
[2]
Turn key to OFF. Remove key
and store out of reach of children.
[3]
Fuel shut-off
[4]
10
Document: - page 10 (Black)
Screen angle and frequency: 45.0000, 150.0000
Push rocker switch
(if equipped) to OFF.
Close fuel shut-off valve
(if equipped).
MAINTENANCE
ENGINE AND ENGINE PARTS
We recommend that you see an authorized Briggs & Stratton Service Dealer for all maintenance and service of the engine
and engine parts. Use only genuine Briggs & Stratton parts.
If you perform any maintenance on the engine, first disconnect the spark plug wire
from the spark plug, and disconnect the battery at the negative terminal (electric
WARNING
starter engines only) to prevent unintentional sparking. Unintentional sparking can
result in fire or electric shock. Unintentional start-up can result in entanglement,
traumatic amputation or laceration. Use only correct tools.
WARNING
• Do not strike the flywheel with a hammer or hard object because the flywheel may
later shatter during operation.
• Do not tamper with governor spring, links or other parts to increase engine speed.
MUFFLER
FUEL SYSTEM
Replacement parts for the muffler
WARNING must be the same and installed in the
WARNING
same position as the original parts,
otherwise fire can occur.
If muffler is equipped with spark arrester screen, remove screen
for inspection. Replace screen if damaged or plugged.
SPARK PLUG
Replacement parts for fuel system
(cap, hoses, tanks, filters, etc.)
must be the same as original parts,
otherwise fire can occur.
REPLACE FUEL FILTER (if equipped)
Use only Briggs & Stratton Spark Tester (part number
19368) to check for spark.
Drain fuel tank or close fuel shut-off valve before replacing
fuel filter. Otherwise, fuel can leak out, creating a
fire/explosion hazard.
Note: In some areas, local law requires using resistor spark
plug to suppress ignition signals. If this engine was
originally equipped with resistor spark plug, use same type
for replacement.
FUEL FILTER
P/N 499638
.030” (0.76 mm)
WIRE GAGE
RESISTOR P/N 491055
FUEL HOSE
CLAMPS
13
Document: - page 13 (Black)
Screen angle and frequency: 45.0000, 150.0000
MAINTENANCE
CLEANING DEBRIS
CAUTION: Do not use water to clean engine parts.
Water could contaminate fuel system. Use a brush
or dry cloth.
Daily or before every use, clean accumulated debris from
engine. Keep linkage, spring and controls clean. Keep area
around and behind muffler free of any combustible debris.
Engine parts should be kept clean to
WARNING reduce the risk of overheating and
ignition of accumulated debris.
Finger Guard,
Linkage, Springs,
Controls,
Muffler and
Spark Arrester
CLEAN
14
Document: - page 14 (Black)
Screen angle and frequency: 45.0000, 150.0000
SERVICE & STORAGE
PARTIAL LIST OF GENUINE BRIGGS &
STRATTON PARTS
PART
BRIGGS & STRATTON
PART NUMBER
Flat air cleaner cartridge
Flat air cleaner pre-cleaner
Model Series 110000 / 120000
Oval air cleaner cartridge
Oval pre-cleaner
Model Series 200000 / 210000
Oval air cleaner cartridge
Oval pre-cleaner
Oil foam air cleaner pre-cleaner
Oil
Fuel filter
Gas additive
Resistor spark plug
Long life platinum spark plug
(used on most OHV engines)
Spark plug wrench
Spark tester
Oil pump kit
491588 -OR- 5043
493537 -OR- 5064
690610 -OR- 5059
273356 -OR- 5059
695302
695303
273332
100005 -OR- 100028
694485
5041
491055
5066
89838 -OR- 5023
19368
5056
(uses standard electric drill to remove oil from engine quickly)
SERVICE
See an Authorized Briggs & Stratton Service Dealer. Each
one carries a stock of Genuine Briggs & Stratton Parts and
is equipped with special service tools. Trained mechanics
assure expert repair service on all Briggs & Stratton
engines. Only dealers advertising as “Authorized Briggs &
Stratton” are required to meet Briggs & Stratton standards.
When you purchase equipment powered by a
Briggs & Stratton engine, you are assured of
highly skilled, reliable service at more than
30,000
Authorized
Service
Dealers
worldwide, including more than 6,000 Master
Service Technicians. Look for these signs
wherever Briggs & Stratton service is offered.
15
Document: - page 15 (Black)
Screen angle and frequency: 45.0000, 150.0000
SERVICE & STORAGE
STORAGE
Engines stored over 30 days need special attention.
[2]
While engine is still warm, change oil.
[1]
[3]
Remove spark plug and pour about 1 oz. (30 ml) of
engine oil into cylinder. Replace spark plug and crank
slowly to distribute oil.
[4]
Clean engine of surface debris, chaff or grass.
To prevent gum from forming in fuel system or on
essential carburetor parts:
a) if fuel tank contains oxygenated or reformulated
gasoline (gasoline blended with an alcohol or an
ether), run engine until it stops from lack of fuel, or b) if
fuel tank contains gasoline, either run engine until it
stops from lack of fuel, or add a gasoline additive to the
gas in the tank. (See parts list. Single – use pouches of
gas additive are available from your service dealer.) If
you use a gas additive, run the engine for several
minutes to circulate the additive through the carburetor.
Then, engine and fuel can be stored up to 24 months.
WARNING
16
Document: - page 16 (Black)
Screen angle and frequency: 45.0000, 150.0000
[5]
Store in a clean, dry area. Do
not store in same area as a
stove, furnace, water heater,
or other appliance that uses a
pilot light or has a device that
can create a spark.
LIMITED WARRANTY
Briggs & Stratton Corporation will repair or replace, free of charge, any part(s) of the engine that is defective in material or workmanship or both.
Transportation charges on parts submitted for repair or replacement under this warranty must be borne by purchaser. This warranty is effective for the
time periods and subject to the conditions stated below. For warranty service, find the nearest Authorized Service Dealer in our dealer locator map
at www.briggsandstratton.com, or by calling 1-800-233-3723, or as listed in the ‘Yellow Pages™’.
THERE IS NO OTHER EXPRESS WARRANTY. IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR FROM PURCHASE, OR TO THE EXTENT PERMITTED BY LAW ANY AND ALL IMPLIED
WARRANTIES ARE EXCLUDED. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES ARE EXCLUDED TO THE EXTENT
EXCLUSION IS PERMITTED BY LAW. Some states or countries do not allow limitations on how long an implied warranty lasts, and some states or
countries do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation and exclusion may not apply to you.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state and country to country.
( "
r
(Sleeve Bore)
!"
(Kool Bore)
!# $
%&r
%!
%45
'
2 years
2 years
1 year
1 year
90 days
90 days
)*
Consumer Use
Commercial Use
*
2 years
1 year
Note the following special warranty periods: 2 years for Classic™ engines in the European Union and Eastern European countries, for all consumer
products in the European Union, and for emission control systems on engines certified by EPA and CARB. 5 years for Consumer use, 90 days for
Commercial use of Touch-N-Mow® starter on Quantum® and Intek™ engines. One year for Consumer use, 90 days for Commercial use on engines
certified to operate on Kerosene fuel. Engines used on Home Standby Generator applications are warranted under Consumer use only. This warranty
does not apply to engines on equipment used for prime power in place of a utility. Engines used in competitive racing or on commercial or rental
tracks are not warrantied.
The warranty period begins on the date of purchase by the first retail consumer or commercial end user, and continues for the period of time stated in the table above. “Consumer use”
means personal residential household use by a retail consumer. “Commercial use” means all other uses, including use for commercial, income producing or rental purposes. Once an
engine has experienced commercial use, it shall thereafter be considered as a commercial use engine for purposes of this warranty.
NO WARRANTY REGISTRATION IS NECESSARY TO OBTAIN WARRANTY ON BRIGGS & STRATTON PRODUCTS. SAVE YOUR PROOF OF PURCHASE
RECEIPT. IF YOU DO NOT PROVIDE PROOF OF THE INITIAL PURCHASE DATE AT THE TIME WARRANTY SERVICE IS REQUESTED, THE
MANUFACTURING DATE OF THE PRODUCT WILL BE USED TO DETERMINE THE WARRANTY PERIOD.
( ( !
" #
$ # !
$ !
% &
' # ( " & #
!" # $ %" " & "" " # " ' & ) *+,-' ./' 0 *+& &1& +' 2,&
,+$3$2- +$33 &+&&,2 *+&
4 ' 5.
6
7 -# # 5/ 8 ! * 2
9:;)6
; * # 5# <=
+ 6 ,$- 3+® ' + , $
9 + % > 8 8
5 17
Document: - page 1 (Black)
Screen angle and frequency: 45.0000, 150.0000
8
,8!
® 8 6 +
, $
? * 8 5. 6 + , $
< ' # "
# 8 @ # # # % " 8 ): +
8 % )) ' "#" "" " "( )## * +
, - ."( + /
" 0-
1#™2 " 0# 3
2 03
#2 04
52 #
! !'!! +,- . /! !" ! +,
. ( 0!& !"! "1 +(22 ,
&! !! 1& 1 & +#3 )/" 1 . 4!,
The California Air Resources Board (CARB), U.S.
EPA and B&S are pleased to explain the Emissions Control System Warranty on your small offroad engine (SORE). In California, new small offroad engines model year 2006 and later must be
designed, built and equipped to meet the State’s
stringent anti-smog standards.
Elsewhere in the United States, new non-road,
spark-ignition engines certified for model year
1997 and later must meet similar standards set
forth by the U.S. EPA. B&S must warrant the emissions control system on your engine for the periods of time listed below, provided there has been
no abuse, neglect or improper maintenance of
your small off-road engine.
Your emissions control system includes parts
such as the carburetor, air cleaner, ignition system, fuel line, muffler and catalytic converter.
Also included may be connectors and other
emissions related assemblies.
Where a warrantable condition exists, B&S will
repair your small off-road engine at no cost to
you including diagnosis, parts and labor.
! &! !! )/" 1 !0
Small off-road engines are warranted relative to emissions control parts defects for a period of two years, subject to provisions set forth below. If any
covered part on your engine is defective, the part will be repaired or replaced by B&S.
#3 1 '!4
As the small off-road engine owner, you are responsible for the performance of the required
maintenance listed in your Operating and Maintenance Instructions. B&S recommends that
you retain all your receipts covering maintenance on your small off-road engine, but B&S
cannot deny warranty solely for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance.
As the small off-road engine owner, you should
however be aware that B&S may deny you warranty coverage if your small off-road engine or a
part has failed due to abuse, neglect, improper
maintenance or unapproved modifications.
You are responsible for presenting your small
off-road engine to an Authorized B&S Service
Dealer as soon as a problem exists.
The undisputed warranty repairs should be
completed in a reasonable amount of time, not
to exceed 30 days.
If you have any questions regarding your warranty rights and responsibilities, you should contact a B&S Service Representative at
1-414-259-5262.
The emissions warranty is a defects warranty.
Defects are judged on normal engine performance. The warranty is not related to an in-use
emissions test.
! &! !! )/" 1 !0!
The following are specific provisions relative to your emissions Control Defects Warranty Coverage. It is in addition to the B&S engine warranty for
non-regulated engines found in the Operating and Maintenance Instructions.
1. Warranted Parts
subsequent purchaser that the Warranted
B&S is not liable to cover failures of WarCoverage under this warranty extends only
Parts shall be free from defects in materials
ranted Parts caused by the use of add-on,
to the parts listed below (the emissions conand workmanship which caused the failure
non-original, or modified parts.
trol systems parts) to the extent these parts
of the Warranted Parts for a period of two 5. Maintenance
were present on the engine purchased.
years from the date the engine is delivered to
Any Warranted Part which is not scheduled
a. Fuel Metering System
a retail purchaser.
for replacement as required maintenance or
•
Cold start enrichment system
3. No Charge
which is scheduled only for regular inspec•
Carburetor and internal parts
Repair or replacement of any Warranted
tion to the effect of “repair or replace as nec•
Fuel Pump
Part will be performed at no charge to the
essary” shall be warranted as to defects for
•
Fuel line, fuel line fittings, clamps
owner, including diagnostic labor which
the warranty period. Any Warranted Part
b. Air Induction System
leads to the determination that a Warranted
which is scheduled for replacement as re•
Air cleaner
Part is defective, if the diagnostic work is
quired maintenance shall be warranted as to
•
Intake manifold
performed at an Authorized B&S Service
defects only for the period of time up to the
c. Ignition System
Dealer. For emissions warranty service
first scheduled replacement for that part. Any
•
Spark plug(s)
contact your nearest Authorized B&S Serreplacement part that is equivalent in perfor•
Magneto ignition system
vice Dealer as listed in the “Yellow Pages”
mance and durability may be used in the perd. Catalyst System
under “Engines, Gasoline,” “Gasoline Enformance of any maintenance or repairs.
•
Catalytic converter
gines,” “Lawn Mowers,” or similar category.
The owner is responsible for the perfor•
Exhaust manifold
4. Claims and Coverage Exclusions
mance of all required maintenance, as de•
Air injection system, Pulse valve
Warranty claims shall be filed in accordance
fined in the B&S Operating and Maintenance
e. Miscellaneous Items
with the provisions of the B&S Engine WarInstructions.
•
Vacuum, temperature, position,
ranty Policy. Warranty coverage shall be ex- 6. Consequential Coverage
time sensitive valves
cluded for failures of Warranted Parts which
Coverage hereunder shall extend to the failand switches
are not original B&S parts or because of
ure of any engine components caused by
•
Connectors and assemblies
abuse, neglect or improper maintenance as
the failure of any Warranted Part still under
2. Length of Coverage
set forth in the B&S Engine Warranty Policy.
warranty.
B&S warrants to the initial owner and each
' / , , , & !
*A 84;?)?? 5, * *6
>>@)><7
>>;?@;4
>>44><7
>>)9?<?
>>)??49
>>:744?
>9@9<@?
>9@9)?>
>9<;@>;
>99?<77
>9;4:?;
>94:);)
>;@94>?
>;@;)?9
>;?4?@:
>;>:9:4
>;9>9)9
>7<4)>>
>7>@974
>79>::7
>7;@><<
>7;?>);
>749:7>
>7))>>7
>4<;)47
>4>7<94
>4>:94@
>4;4<4<
>47@?:@
>47?999
>47:>?<
>4)7:<7
>4:4>)>
>);9;<?
>);449?
>)79;4>
>))>4)4
>):99;<
>7;?>);
>:<4747
>:??:>7
>:>;:4?
>:;:?>?
>:);<:<
>:)4;4:
9@@47>?
9@:;)4;
9<@;?)9
9<<?>?<
9<94@9)
9<;77;9
9<47)97
9<)@9)7
9<)77<;
9<:@@9<
9<:7:79
9?>9?)7
9?74999
9>;9:49
9>;4?:)
9>4<794
9>)@<;9
9>:>@;<
9>:><9)
9>:9)7:
9;@?>?@
18
Document: - page 2 (Black)
Screen angle and frequency: 45.0000, 150.0000
99;<@99
99;>@:)
9;;9:);
99:7)49
99:)4:7
9;@?>?@
974:?@9
97:)>;7
94?)7>7
94>@?)7
94>9?::
94;7<?<
9479@;7
947;:7<
944<;<?
9)@?;4>
9)@?;49
9)@?;44
9)@)<>;
9)<<:>@
9)<>);4
9)9:>?;
9)7<@@>
9:<><@:
9:?:<4@
9:9<9;;
9:;:>;;
9::@4:<
;@@>@9>
;@??<?@
;@??<??
;@?)4)@
;<@9))@
;<?9;;<
;<)@9@7
;?4:>7<
;?)@><4
;>7799>
;>7:;@<
;944:<:
;94:4<<
;9)4;@@
;;979:?
;;7:@<;
;?>>4@
;9?<@)
7><)<?
7?9@>7
7:@;9?
7?4<?)
7>)??)
79>@9)
7:@;9?
7:<<?4
7:<<?)
(Cette page ne s'applique que pour le Canada et les Etats-Unis)
Déclaration de garantie pour les défauts de contrôle d'émissions pour la Californie, les ÉtatsĆUnis et le Canada.
moteur tout terrain ne soit pas mal utilisé, négligé ou que son entretien ne soit pas défectueux.
Le California Air Resources Board (CARB), U.S. EPA et B&S ont le plaisir de vous expliquer la
Le système de contrôle des émissions comprend des pièces comme le carburateur, le filtre à air,
garantie du système de contrôle des émissions pour votre petit moteur tout terrain. En Californie,
le système d'allumage, la Durit de carburant, le silencieux et le convertisseur catalytique. Des
les petits moteurs tout terrain à partir de l'année 2006 doivent être conçus, fabriqués et équipés
connecteurs et d'autres assemblages impliqués dans les émissions peuvent aussi en faire partie.
pour répondre aux normes sévères antibrouillard de l'état. Ailleurs aux ÉtatsĆUnis, les nouveaux
Si la condition de garantie est remplie, Briggs & Stratton réparera gratuitement votre moteur y
moteurs tout terrain à allumage commandé par bougie depuis l'année 1997 doivent répondre à
compris le diagnostic, les pièces et la mainĆd'Ĺuvre.
des normes semblables édictées par la U.S. EPA. B&S doit garantir le système de contrôle des
émissions de votre moteur pendant les durées indiquées ciĆaprès, en supposant que le petit
Couverture de la garantie de défectuosité du contrôle des émissions de Briggs & Stratton
Les petits moteurs tout terrain sont garantis en ce qui concerne les défauts des pièces du contrôle d'émission pendant une période de deux ans, aux conditions énoncées plus loin. Si une pièce de votre
moteur couverte par cette garantie est défectueuse, Briggs et Stratton la réparera ou la remplacera.
Responsabilités du propriétaire au titre de la garantie
En tant que propriétaire d'un petit moteur non routier, vous êtes responsable de l'entretien nécesĆ
saire indiqué dans les instructions de fonctionnement et d'entretien. Briggs & Stratton recommanĆ