Owner`s manual | Brinkmann 100 Gas Grill User Manual

Heavy-Duty Gas Grill
Parrilla de Gas de Alta Resistencia
OWNER’S MANUAL / MANUAL DEL PROPIETARIO
ASSEMBLY AND OPERATING INSTRUCTIONS
INSTRUCCIONES DE ARMADO Y OPERACIÓN
SAVE THIS MANUAL FOR FUTURE REFERENCE
GUARDE ESTE MANUAL PARA REFERENCIA FUTURA
WARNING/ADVERTENCIA
NOTICE TO INSTALLER:
LEAVE THESE INSTRUCTIONS
WITH THE GRILL OWNER FOR
FUTURE REFERENCE.
AVISO PARA EL
INSTALADOR:
HAZARDOUS EXPLOSION MAY RESULT IF THESE WARNINGS AND INSTRUCTIONS
ARE IGNORED. READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS IN THIS
MANUAL TO AVOID PERSONAL INJURY, INCLUDING DEATH OR PROPERTY DAMAGE.
SE PUEDE PRODUCIR UNA EXPLOSIÓN PELIGROSA SI SE HACE CASO OMISO A
ESTAS ADVERTENCIAS E INSTRUCCIONES. LEA Y SIGA TODAS LAS ADVERTENCIAS
E INSTRUCCIONES EN ESTE MANUAL PARA EVITAR LESIONES PERSONALES,
INCLUSO LA MUERTE, O LOS DA—OS MATERIALES.
ENTREGUE ESTAS
INSTRUCCIONES AL
PROPIETARIO DE LA PARRILLA
PARA REFERENCIA FUTURA.
300
200
100
Read Instructions
Before Lighting:
1. Open lid during lighting.
2. Select a burner to be lit. Push
and turn control knob of that
burner to “HIGH.” Press
electronic igniter and hold for
3-5 seconds.
3. If ignition does not occur in
5 seconds, turn control knob
to “OFF,” wait 5 minutes and
repeat lighting procedure.
400
500
600
SEAR BURNER
HORNILLA PARA
DORAR
FOR OUTDOOR
USE ONLY
SOLAMENTE PARA
USO EN EXTERIORES
Lea las Instrucciones
Antes de Iluminación:
1. Abra la tapa durante el
encendimiento.
2. Seleccione la hornilla que va a
encender. Empuje y gire la
perilla de control de esa
hornilla a la posición “ALTO”.
Oprima el encendedor
electrónico
y manténgalo oprimido
3 a 5 segundos.
NG Conversion
Kit Required
Kit de la Conversión
del NG Requerido
4. Continue to push in control knob for 30 seconds after sear burner is lit.
1. Abra la tapa durante el encendimiento.
MAXIMUM SEAR BURNER
WEIGHT = 15 lbs.
PESO MÁXIMO DE LA HORNILLA
PARA DORAR = 6.8 kg
3. Si la hornilla NO se enciende
en 5 segundos, gire la perilla
de control a la posición
"APAGADO"espere 5 minutos y
repita el procedimiento de
encendido.
LIGHTS
LUCES
1. Open lid during lighting.
2. Push and turn control knob to “HIGH” and continue to push in.
3. Press electronic igniter and hold for 3 to 5 seconds.
Instrucciones de Iluminación para la Hornilla
para Dorar:
Escanear con un
Teléfono Inteligente
para Más Información
800-527-0717
For Accessories, Parts or Assistance, Call
or Visit our Website
Para Accesorios, Partes o Asistencia,
Llame o Visite Nuestro Sitio de Internet
Sear Burner Lighting Instructions:
5. If ignition does not occur in 5 seconds, turn control knob to “OFF,” wait 5
minutes and repeat lighting procedure.
Scan with a Smart Phone
for More Information
ELECTRONIC
IGNITER
ENCENDEDOR
ELECTRÓNICO
2. Empuje la perilla de control y gire a la posición “ALTO” y continúe
empujando hacia adentro.
3. Presione el encendedor electrónico y sosténgase por 3 a 5 segundos.
4. Continúe empujando la perilla de control hacia adentro por
30 segundos después de que la hornilla para dorar se enciende.
5. Si la hornilla NO se enciende en 5 segundos, gire la perilla de control a la
posición "APAGADO", espere 5 minutos y repita el procedimiento de
encendido.
IMPORTANT SAFETY
WARNINGS
WE WANT YOU TO ASSEMBLE AND USE YOUR GRILL AS SAFELY AS POSSIBLE.
IS TO ATTRACT YOUR ATTENTION
THE PURPOSE OF THIS SAFETY ALERT SYMBOL
TO POSSIBLE HAZARDS AS YOU ASSEMBLE AND USE YOUR GRILL.
WHEN YOU SEE THE SAFETY ALERT SYMBOL
PAY CLOSE ATTENTION TO THE INFORMATION WHICH FOLLOWS!
READ ALL SAFETY WARNINGS AND INSTRUCTIONS CAREFULLY
BEFORE ASSEMBLING AND OPERATING YOUR GRILL.
DANGER
IF YOU SMELL GAS:
1.
Shut off gas to the appliance.
2. Extinguish any open flame.
3. Open lid.
4. If odor continues, keep away from the appliance and immediately call your gas supplier or your
fire department.
WARNING
1.
Do not store or use gasoline or other flammable liquids or vapors in the vicinity of this or any
other appliance.
2. An LP cylinder not connected for use shall not be stored in the vicinity of this or any other
appliance.
DANGER
a) Do not store a spare LP cylinder under or near this appliance.
b) Never fill the cylinder beyond 80% full.
c) If the information in (a) and (b) is not followed exactly, a fire causing death or
serious injury may occur.
1
TABLE OF CONTENTS:
General Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
LP Gas Cylinder (Tank) Specifications and Installation . . . . . . . . . . . . . . . . 4-6
Hose & Regulator Specifications and Installation . . . . . . . . . . . . . . . . . . . . 6-7
Leak Testing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-8
Pre-start Check List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Lighting Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-10
Operating the Grill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-12
Proper Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-15
Transporting and Storage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-17
Grill Cooking Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Assembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-30
Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
WARNING: Be alert to the possibility of serious bodily injury if the instructions are not followed. Be sure to read and
carefully follow all of the messages.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
CALIFORNIA PROPOSITION 65 WARNING
This product contains chemicals, including lead in the brass of certain component parts, that are
known to the State of California to cause cancer, and birth defects or other reproductive harm.
Wash hands after handling. When used, this product emits fuel combustion chemicals that are known
to the State of California to cause cancer, and birth defects or other reproductive harm.
Follow all instructions in this manual and use only in well ventilated, outdoor area.
FOR COVERS, ACCESSORIES AND OTHER PRODUCTS, PLEASE VISIT US ONLINE AT:
2
GENERAL WARNINGS:
WARNING
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
3
Leak test all connections before first use, even if grill was purchased fully assembled and after
each tank refill. Check the propane tank rubber seal for damage.
Always check the grill and propane tank prior to each use as indicated in the “Checking for
Leaks” & “Pre-Start Check List” sections of this manual.
Never use natural gas in a unit designed for liquid propane gas.
Never use charcoal, lava rocks or wood briquets in a gas grill. Flavoring chips must be
contained in a metal smoking box to contain ash and prevent fires.
Ensure flames come out of all burner ports at each use. Spiders and insects like to build nests
in burner tubes. Blocked burner tubes can prevent gas flow to the burners and could result in a
burner tube fire or fire beneath the grill.
Never check for leaks using a match or open flame.
Never use or store gasoline, lighter fluid, paint thinner, or other flammable vapors and liquids or
combustible materials in or near your grill.
DO NOT block ventilation areas in sides, back or cart compartment of grill.
DO NOT cover cooking grates or other components with aluminum foil, as this blocks ventilation
and damage to grill or personal injury may occur.
Never place more than 15 pounds on the side tables. DO NOT lean on the side tables. DO NOT
lift grill using side tables.
Keep children and pets away from hot grill. DO NOT allow children to use or play near this grill.
DO NOT leave the grill unattended while ON or in use.
DO NOT allow the gas hose to come in contact with hot surfaces. Redirect the gas hose if
necessary.
DO NOT allow grease or hot drippings to fall on hose and regulator assembly. If this occurs, turn
gas supply OFF at once. Empty grease tray/cup and clean the hose and regulator assembly and
inspect for damage before use.
Never cook on the grill without the grease cup/tray in position.
Keep any electrical supply cords away from water or heated surfaces.
DO NOT use water on a grease fire. Closing the lid to extinguish a grease fire is not possible.
Use type BC dry chemical fire extinguisher or smother with dirt, sand or baking soda.
DO NOT use while under the influence of drugs or alcohol.
FOR OUTDOOR USE ONLY. DO NOT operate indoors or in an enclosed area such as a garage, shed
or breezeway.
Position your grill outdoors on a non-combustible level surface in a well ventilated location, a
safe distance 10 ft. (3.1 m) from combustible materials, buildings and overhangs.
Apartment dwellers: Check with management and follow the requirements and fire codes for using
an LP gas grill in your apartment complex. Only use outside on the ground (not on a balcony,
patio, garage, etc) with a 15 foot (4.6 m) minimum clearance on all sides from any wall, structure or
combustible material.
Maintain a minimum clearance of 36 inches (91 cm) between all sides of grill, deck railings, walls or
other combustible material. Not adhering to these clearances may prevent proper ventilation and can
increase the risk of a fire and/or property damage, which could also result in personal injury. DO NOT
use grill under overhead unprotected combustible construction.
DO NOT use or install this grill in or on a recreational vehicle and/or boat.
DO NOT build this model grill in any built-in or slide in construction.
If a bristle brush is used to clean any of the cooking surfaces, ensure no loose bristles remain on the
cooking surfaces prior to grilling as loose bristles may attach to food.
DO NOT store items in cart that can catch fire or damage your grill (such as swimming pool
supplies/chemicals, table cloth, wood chips).
•
Grill is hot when in use. To avoid burns:
•
•
•
•
•
•
DO NOT attempt to move the grill.
Block the wheels so the unit does not accidentally move.
Wear protective gloves or oven mitts.
DO NOT touch any hot grill surfaces.
DO NOT wear loose clothing or allow hair to come in contact with grill.
Not for commercial use. DO NOT use this grill for anything other than its intended purpose.
USE CAUTION AND COMMON SENSE WHEN OPERATING YOUR GAS GRILL.
FAILURE TO ADHERE TO THE SAFETY WARNINGS AND GUIDELINES IN THIS MANUAL
COULD RESULT IN SEVERE BODILY INJURY OR PROPERTY DAMAGE.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
LP GAS CYLINDER (TANK) SPECIFICATIONS AND INSTALLATION:
WARNING
•
ONLY connect this grill to a Type 1 cylinder valve. The Type 1 valve can be identified with the
large external threads on the valve outlet.
•
DO NOT connect to a propane cylinder exceeding a 20 lb. (9.1 kg) capacity.
•
DO NOT connect to a cylinder that uses any other type of valve connection device.
•
Inspect the propane tank valve rubber seal for cracks, wear or deterioration prior to use. A
damaged rubber seal can cause a gas leak, possibly resulting in an explosion, fire or severe
bodily harm.
•
Turn off the cylinder valve when your grill is not in use.
•
Handle the tank with care.
•
Always secure the cylinder in an upright position.
•
Never connect an unregulated LP gas cylinder to your grill.
•
DO NOT expose LP gas cylinders to excessive heat or ignition sources.
•
DO NOT store a spare LP gas cylinder under or near your grill.
•
Allow only qualified LP gas dealers to fill or repair your LP gas cylinder.
•
DO NOT allow the cylinder to be filled beyond 80% capacity.
•
Read and follow all warnings and instructions that are on the cylinder and that accompany this
product.
DANGER
•
DO NOT store a spare LP gas cylinder (full or empty) under or near your grill. This could cause
excess pressure to be expelled through the vapor relief valve resulting in fire, explosion, or
severe personal injury, including death.
•
Propane gas is heavier than air and will collect in low areas. Proper ventilation is extremely
important. Keep the ventilation opening(s) of the LP gas cylinder enclosure free and clear from
obstructions and debris.
•
DO NOT insert any foreign objects into the cylinder valve outlet as this could damage the
rubber seal. Do not use propane tank with a damaged rubber seal. A damaged rubber seal can
cause a gas leak, possibly resulting in explosion, fire, severe bodily harm, or death. Inspect
rubber seal for cracks, wear or deterioration prior to use.
•
Always keep cylinder (tank) in upright position during use, transit or storage.
4
LP GAS CYLINDER (TANK) SPECIFICATIONS:
LP gas cylinder (not supplied with this grill)
The LP (Liquid Propane) gas cylinder specifically designed to be used with this grill must be 12” (30.5 cm)
diameter x 18” (45.7 cm) tall and have a 20 lb. (9.1 kg) capacity incorporating a Type 1 cylinder valve and
an over-filling protection device (OPD).
This grill is designed to fit Worthington, Manchester or SMPC brand 20 lb. (9.1 kg) cylinders. Other brand
DOT cylinders may fit this grill if the cylinder has similar dimensions of the top and bottom rings.
The installation of this appliance must be in accordance with:
All applicable local codes, or in the absence of local codes, either:
•
•
•
•
National Fuel Gas Code ANSI Z223.1 NFPA 54
Natural Gas and Propane Installation Code: CAN/CGA B149.1
Natural Gas Installation Code: CAN/CGA B149.1 (Canada)
Propane Installation Code: CAN/CGA B149.2 (Canada)
To check your local codes, see your local LP gas dealer or natural gas company. This grill was not
intended to be connected to a natural gas supply line. If an external electrical source is utilized, it must be
electrically grounded in accordance with local codes, or in the absence of local codes, with the National
Electrical Code, ANSI/NFPA 70, or the Canadian Electrical Code, CSA 22.1.
When purchasing or exchanging a cylinder for your gas grill, it must be constructed and marked in
accordance with the specifications for LP gas cylinders of the U.S. Department of Transportation (DOT)
or the National Standard of Canada, CAN/CSA-B339 Cylinders, Spheres and Tubes for Transportation of
Dangerous Goods; and Commission, as applicable; and provided with a listed over-filling prevention device
(OPD), and provided with a cylinder connection device compatible with the connection for outdoor cooking
appliances.
The cylinder must also be equipped with:
•
•
•
•
•
•
A shut-off valve terminating in a Type 1 gas cylinder valve outlet.
A Type 1 valve that prevents gas flow until a positive seal is obtained.
An arrangement for vapor withdrawal.
A collar to protect the cylinder shut-off valve.
A safety relief device having direct communication with the vapor space of the cylinder.
A listed over-filling prevention device (OPD).
FILLING THE LP GAS CYLINDER (TANK):
WARNING
5
•
Allow only qualified licensed LP gas dealers to properly fill or repair your LP gas cylinder.
•
New tanks should be purged prior to filling; inform LP gas dealer if you are using a new tank.
•
DO NOT allow the cylinder to be filled beyond 80% capacity. Over-filled tanks can create a
dangerous condition. Over-filled tanks can build-up pressure and cause the relief valve to expel
propane gas vapors. The vapor is combustible and if it comes in contact with a spark source or
flame an explosion causing severe burns, bodily harm, or death could occur.
•
Always use a protective cylinder cap when grill is not connected to cylinder.
•
If you exchange a cylinder with a qualified exchange program, the new cylinder must have
a Type 1 valve and an over-filling prevention device (OPD).
•
Inspect the propane tank valve rubber seal for cracks, wear or deterioration prior to use. A
damaged rubber seal can cause a gas leak, possibly resulting in an explosion, fire or severe
bodily harm.
LP GAS CYLINDER (TANK) RUBBER SEAL INSPECTION:
•
Inspect the propane tank valve rubber seal for cracks,
wear or deterioration prior to use. A damaged rubber
seal can cause a gas leak, possibly resulting in an
explosion, fire or severe bodily harm.
•
Inspection should be done each time the propane tank
is connected to the grill, has been refilled, exchanged or
has not been used for more than 60 days.
•
Do not use a propane tank with a damaged rubber seal.
Exchange the tank or have the rubber seal replaced at a
qualified propane filling station.
Good
Rubber Seal
Damaged
Rubber Seal
INSTALLING THE LP GAS CYLINDER (TANK) ONTO THE GRILL:
1.
Check that the cylinder valve is closed by turning the knob clockwise. Inspect cylinder valve rubber seal
for cracks or deterioration. Do not use propane tank with damaged seal as a gas leak may occur.
2. Place the cylinder into the tank holder in the bottom of cabinet.
3. Orient the cylinder such that the valve opening faces the right side of the grill, and the hose is not
kinked or damaged.
Tank Holder
HOSE & REGULATOR SPECIFICATIONS AND INSTALLATION:
WARNING
•
DO NOT attempt to connect grill, as purchased for LP (propane) gas, to any other fuel supply
source such as a natural gas line.
•
DO NOT use any other pressure regulator/hose assembly other than the one supplied with your grill.
Replacement pressure regulator/hose assembly must be part No 155-4580-0, which can be obtained
by contacting customer service at 800-272-4443.
•
DO NOT attempt to adjust or repair a regulator. The regulator is designed to operate at a
maximum output pressure of 11 inches of water column (2.74 kPa).
•
Ensure the tank valve is CLOSED prior to connecting the LP gas cylinder to your grill. Turn the
valve knob clockwise to properly close the valve. Read and follow all instructions and warnings
on the supply hose safety tags. Read and follow all warnings in this manual concerning the safe
use of LP gas cylinders and the hose and regulator before connecting cylinder to grill. Read and
follow all warnings on the LP cylinder.
6
HOSE AND REGULATOR:
Your grill is equipped with a Type 1 connection device with the following features:
1. The system will not allow gas flow from the cylinder until a positive connection to the valve has been made.
Note: The cylinder valve and all grill burner knobs must be turned OFF before any connection is made or
removed.
2. A regulator flow limiting device, when activated, restricts the flow of gas to 10 cubic feet per hour. If the
flow limiting device is activated, perform Regulator Resetting Procedure.
Note: If your grill will not get hot enough to cook, the flow limiting device may have been activated.
CONNECTING HOSE AND REGULATOR:
1. Inspect the propane tank valve rubber seal for cracks, wear or
deterioration prior to use. A damaged rubber seal can cause a gas
leak, possibly resulting in an explosion, fire or severe bodily harm. Do
not use a propane tank with a damaged rubber seal.
2. Attach or detach regulator to the LP gas cylinder only when cylinder is
at rest in tank holder.
3. Check that the cylinder valve is closed by turning the knob clockwise.
4. Check that the grill’s burner control knobs are in the “OFF” positions.
Inspect Rubber Seal (see page 6)
5. Visually inspect the hose assembly prior to each use for evidence of damage, excess wear, or
deterioration. If found, replace the assembly before using your grill. Only the manufacturer’s supplied
replacement should be used.
6. Remove the protective plastic cap from the cylinder valve.
7. Check that the hose does not contain kinks, does not contact sharp edges, and does not contact
surfaces that may become hot during use.
8. Hold regulator and insert the brass nipple into the LP cylinder valve outlet. Ensure that the device is
centered properly.
9. Turn the large coupling nut clockwise by hand and tighten to a full stop. Take care not to cross thread
the coupling nut onto the cylinder valve. Do not use tools to tighten connection.
Note: If you are unable to make the connection, repeat Steps 7 and 8.
10. Leak check all fittings before lighting your grill. See section on “Leak Testing” in this manual.
REGULATOR RESETTING PROCEDURE:
If your grill will not get hot enough to cook, the flow limiting device may have been activated.
Mini Reset:
1.
Turn ALL burner control knobs to “OFF”, turn off the cylinder valve. Wait one minute. Slowly turn
cylinder valve ON and relight grill. If burner flame is higher and grill heats up properly – proceed with
cooking.
Full Reset:
1.
Turn ALL burner control knobs to “OFF”, turn off the cylinder valve. Disconnect hose and regulator from
cylinder. Wait two minutes, reattach hose and regulator and perform leak test.
LEAK TESTING:
WARNING
•
7
Never use your grill without leak testing all gas connections, hoses and propane tank. Follow
the section on “Leak Testing” in this manual for proper procedures.
DANGER
To prevent fire or explosion hazard:
• DO NOT smoke or permit ignition sources in the area while conducting a leak test.
• Perform test OUTDOORS in a well ventilated area that is protected from the wind.
• Never perform a leak test with a match or open flame.
• Never perform a leak test while the grill is in use or while grill is still hot.
WHEN TO PERFORM A LEAK TEST:
•
•
•
•
After assembling your grill and before lighting for the first time, even if purchased fully assembled.
Every time the LP gas cylinder is refilled, exchanged or if any of the gas components are disconnected or
replaced.
Any time your grill has been moved.
At least once per year or if your grill has not been used for more than 60 days.
CHECKING FOR LEAKS:
CAUTION:
Strong odors, colds, sinus congestion, etc. may prevent the detection of propane by smell.
Use caution and common sense when testing for leaks.
Note: The leak test must be performed in an area that has adequate lighting in order to see if bubbles are
developing and not in a windy or noisy area so larger leaks can be detected by smell or sound.
1. Create a mixture of 50% water and 50% liquid dishwashing soap.
Watch For Bubbles
2. Open the lid.
3. Ensure all control knobs are set to the “OFF” position.
4. Turn on the gas at the cylinder valve. Turn the cylinder valve knob counterclockwise to full open. If you hear a rushing sound or smell gas, turn the gas
off. Tighten any leaking connections. If leak is detected at connection nut and
tightening does not stop leak, reinspect propane tank rubber seal.
5. Apply the soapy water mixture to the following:
A Supply tank (cylinder) welds.
F
H
B Connection nut to tank valve.
C Back side of connection nut to brass nipple.
D Brass nipple connection into regulator.
G
E Regulator connections to gas supply hoses.
F Side burner valve stem cap.
G Side burner connection to hose.
I
E
H Hose connection to gas manifold.
I The full length of gas supply hose.
J
J Tank valve to cylinder.
D
6. Check each place listed (A–J) for growing bubbles, which indicates a leak.
C
Large leaks may not be detected by bubbles but should produce
B
a rushing sound or gas smell.
A
7. Turn off gas supply at cylinder valve.
8. Turn on control knobs to release gas pressure in hose.
9. Turn control knobs to “OFF” position.
10. Tighten any leaking connections. If leak is detected at connection nut and tightening does not stop leak, reinspect
propane tank rubber seal. (see page 6)
11. Repeat soapy water test until no leaks are detected.
12. Turn off gas supply at cylinder valve until you are ready to use your grill.
13. Wash off soapy residue with cold water and towel dry.
14. Wait 5 minutes to allow all gas to evacuate the area before lighting grill.
WARNING: DO NOT use the grill if leaks cannot be stopped. Contact a qualified gas appliance repair service.
8
PRE-START CHECK LIST:
DANGER
Property damage, bodily harm, severe burns, and death could result from failure to follow these
safety steps. These steps should be performed after the grill has been assembled and prior to
each use. DO NOT operate this grill until you have read and understand ALL of the warnings and
instructions in this manual.
•
Ensure that the grill is properly assembled.
•
Inspect the gas supply hose for burns, chaffing, kinks, and proper routing before each use. If it is
evident there is excessive abrasion or wear, or the hose is cut, it must be replaced prior to the grill
being used. Replace with hose and regulator Model No. 155-4580-S, which can be obtained by
contacting customer service at 800-527-0717.
•
Leak check all gas connections, hose and propane tank. See section on “Leak Testing”.
•
Ensure that all electrical supply cords are properly grounded. Keep any electrical supply cord and the
fuel supply hose away from any heated surfaces. Hose should be at least 3 inches from hot surfaces.
•
Position your grill on a non-combustible level surface in a well ventilated location, a safe distance
10 ft. (3.1 m) from combustible materials, buildings and overhangs.
•
Properly place the empty grease cup under the grease drain hole in the bottom of the grill to catch
grease during use.
•
DO NOT block ventilation areas in sides, back or cart compartment of grill.
LIGHTING INSTRUCTIONS:
WARNING
Read, understand and follow all warnings and instructions contained in this manual. DO NOT skip any
of the warnings and instructions contained in the preceding sections of this manual.
Follow the instructions exactly.
1.
OPEN THE GRILL LID before attempting to light a burner so that fumes do not accumulate inside
the grill. An explosion could occur if grill lid is down.
2. Check that all burner control knobs and the cylinder valve are turned to the “OFF” position.
3. Turn on the fuel supply by slowly rotating the cylinder valve knob counter-clockwise to full open.
4. DO NOT stand with head, body, or arms over the grill when lighting.
LIGHTING THE MAIN BURNERS:
1.
Open lid before lighting burner.
Lea las Instrucciones
Antes de Iluminación:
1. Open lid during lighting.
1. Abra la tapa durante el
encendimiento.
2. Select a burner to be lit. Push
and turn control knob of that
burner to “HIGH.” Press
electronic igniter and hold for
3-5 seconds.
2. Make sure all control knobs are in the “OFF” position.
3. Select the burner to be lit. Push and turn the control knob
of that burner to the “HIGH” position
Read Instructions
Before Lighting:
3. If ignition does not occur in
5 seconds, turn control knob
to “OFF,” wait 5 minutes and
repeat lighting procedure.
FOR OUTDOOR
USE ONLY
SOLAMENTE PARA
USO EN EXTERIORES
2. Seleccione la hornilla que va a
encender. Empuje y gire la
perilla de control de esa
hornilla a la posición “ALTO”.
Oprima el encendedor
electrónico
y manténgalo oprimido
3 a 5 segundos.
Scan with a Smart Phone
for More Information
Escanear con un
Teléfono Inteligente
para Más Información
3. Si la hornilla NO se enciende
en 5 segundos, gire la perilla
de control a la posición
"APAGADO"espere 5 minutos y
repita el procedimiento de
encendido.
LIGHTS
LUCES
NG Conversion
Kit Required
Kit de la Conversión
del NG Requerido
800-527-0717
For Accessories, Parts or Assistance, Call
or Visit our Website
Para Accesorios, Partes o Asistencia,
Llame o Visite Nuestro Sitio de Internet
4. Press the electronic igniter and hold for 3–5 seconds to light burner
5. If ignition does NOT occur in 5 seconds, turn control knob to “OFF”, wait 5 minutes to allow gas to
dissipate and repeat lighting procedure.
9
ELECTRONIC
IGNITER
ENCENDEDOR
ELECTRÓNICO
6. Repeat steps 3–5 for lighting each burner. Always use electronic igniter for lighting each burner. If burner
does not ignite using the push-button igniter, wait 5 minutes, see “Match Lighting the Main Burners”
section.
7. To turn off, turn each control knob clockwise until it locks in the “OFF” position. This does not turn off the
gas flow from the cylinder..
Note: If burner does not light or flame is too low, See “Trouble Shooting” section of the owners manual.
MATCH LIGHTING THE MAIN BURNERS:
Lighting Hole
1. Open lid before lighting.
2. Make sure all control knobs are in the “OFF” position.
3. Place a paper match in the end of the matchlighter. Strike the match and
place through lighting hole in the left hand side of the grill to approximately
1/2” (1 to 2 cm) from the burner.
4. Turn on the FAR LEFT burner control knob to the “HIGH” position. The
burner should light within 5 seconds.
5. If the burner does not light, turn the control knob to “OFF” and wait
5 minutes for gas to dissipate and repeat lighting procedure.
Matchlighter
6. Once lit, light adjacent burners in sequence by pressing in and rotating the
control knob to the “HIGH” position.
7. If the burner does not light within the first few attempts of match lighting, there is a problem with the gas
supply. Turn off the gas at the burner and cylinder. DO NOT attempt to operate the grill until the problem
is found and corrected.
Note: If burner does not light or flame is too low, See “Trouble Shooting”
section of the owners manual.
Note: Observe flame height when lit: Flame should be a Blue/Yellow
color between 1”–2” when burner is on “HIGH”.
See section in manual on burner adjustment to adjust flame.
LIGHTING THE SEAR BURNER:
1. Open lid before lighting sear burner.
2. Make sure control knob is in the “OFF” position.
3. Push and turn the control knob to the “HIGH” position. Continue to push
in control knob while pressing electronic igniter for 3–5 seconds.
4. Once burner is lit, continue to push and hold control knob for
30 seconds.
5. If ignition does NOT occur in 5 seconds, turn control knob to “OFF”,
wait 5 minutes to allow gas to dissipate and repeat lighting procedure.
6. To turn off, turn control knob clockwise until it locks in “OFF” position.
Note: If burner does not light or flame is too low, See “Trouble
Shooting” section of the owners manual.
SEAR BURNER
HORNILLA PARA
DORAR
Sear Burner Lighting Instructions:
1. Open lid during lighting.
2. Push and turn control knob to “HIGH” and continue to push in.
3. Press electronic igniter and hold for 3 to 5 seconds.
4. Continue to push in control knob for 30 seconds after sear burner is lit.
5. If ignition does not occur in 5 seconds, turn control knob to “OFF,” wait 5
minutes and repeat lighting procedure.
Instrucciones de Iluminación para la Hornilla
para Dorar:
1. Abra la tapa durante el encendimiento.
MAXIMUM SEAR
BURNER WEIGHT = 15 lbs.
PESO MÁXIMO DE LA HORNILLA
PARA DORAR = 6.8 kg
2. Empuje la perilla de control y gire a la posición “ALTO” y continúe
empujando hacia adentro.
3. Presione el encendedor electrónico y sosténgase por 3 a 5 segundos.
4. Continúe empujando la perilla de control hacia adentro por
30 segundos después de que la hornilla para dorar se enciende.
5. Si la hornilla NO se enciende en 5 segundos, gire la perilla de control a la
posición "APAGADO", espere 5 minutos y repita el procedimiento de
encendido.
MATCH LIGHTING THE SEAR BURNER:
1.
2.
3.
4.
Open the lid to the sear burner before lighting.
Turn the burner control knob to “OFF”.
Strike and carefully place a match approximately 1/2” (1 to 2 cm) from the burner.
Push and turn the sear burner control knob to the “HIGH” position. Continue to push in control knob
while holding a match to burner. The burner should light within 5 seconds.
5. Once burner is lit, continue to push and hold control knob for 30 seconds.
6. If the burner does not light, turn the control knob to “OFF” and wait 5 minutes for gas to dissipate and
repeat lighting procedure.
7. If the burner does not light within the first few attempts of match lighting, there is a problem with the gas
supply. Turn off the gas at the burner and cylinder. DO NOT attempt to operate the sear burner until the
problem is found and corrected.
Note: If burner does not light or flame is too low, See “Trouble Shooting” section of the owners manual.
10
OPERATING THE GRILL:
WARNING
•
•
•
•
•
•
•
Read and follow all warnings and instructions contained in the preceding sections of this
manual.
Never use charcoal, lava rocks or wood briquets in a gas grill. Flavoring chips must be
contained in a metal smoking box to contain ash and prevent fires.
DO NOT cover cooking grates or other components with aluminum foil, as this blocks
ventilation and damage to grill or personal injury may occur.
DO NOT leave your grill unattended while “ON” or in use.
DO NOT move grill when in use.
DO NOT use water on a grease fire. Closing the lid to extinguish a grease fire is not possible.
Use type BC dry chemical fire extinguisher or smother with dirt, sand or baking soda.
Never cook on the grill without the grease cup/tray in place.
BREAKING IN YOUR GRILL:
•
•
In manufacturing and preserving the components of your grill, oil residue may be present on the
burners and cooking surfaces of your grill.
Before cooking on your grill for the first time you should preheat it for 15 minutes on “HIGH” to burn off
these residual oils.
PREHEATING THE GRILL:
•
Prior to each use, it is recommended that you preheat your grill. This ensures that the grilling surfaces
are at the desired temperatures to sear the food sugars when cooking. After lighting your grill, set the
main burner control knobs to the “HIGH” position for 5 to 10 minutes. Close the lid during the preheat
period.
CONTROLLING FLARE-UPS/GREASE FIRES:
•
•
•
•
•
Flare-ups are a part of cooking meats on a gas grill. This adds to the unique flavor of cooking on a gas
grill. Use caution when opening the lid as sudden flare-ups may occur. Excessive flare-ups can overcook your food and cause a dangerous situation for you and your grill. Excessive flare-ups result from
the build-up of grease in your grill. If this should occur, DO NOT pour water onto the flames. This can
cause the grease to splatter and could result in serious burns or bodily harm.
If grease fire occurs while lid is open, leave lid open, turn burner knobs to “OFF”, turn off LP cylinder
valve. If possible, relocate food to a different section of cooking grate and allow grease to burn out or
smother the flames with baking soda.
If grease fire occurs while lid is closed, leave lid closed, as a sudden burst of air may increase flames.
Turn burner knobs to “OFF”, turn off LP cylinder valve. Allow grease to burn out.
Never pour water on a grease fire as grease may splatter/spread and could result in bodily injury or
property damage.
If grease fire does not quickly burn out or the fire is growing/spreading, use type BC dry chemical fire
extinguisher or smother with dirt, sand or baking soda. Closing the lid to extinguish a grease fire is not
possible.
TO MINIMIZE FLARE-UPS:
•
•
•
•
Trim excess fat from meats prior to cooking.
Cook meats with high fat contents (chicken or pork) on Low settings or indirectly.
Ensure that your grill is on level ground and the grease is allowed to evacuate the grill through the
drain hole in the bottom and into grease cup/tray.
Clean grill frequently to minimize grease buildup.
INDIRECT COOKING:
•
11
Indirect cooking is the process of cooking your food without the heat source being directly under your
food. You can sear meats over a high flame on one side of the grill while slow cooking a roast on the
other (unlit) side of the grill.
ROTISSERIE COOKING:
•
•
•
Your grill was pre-drilled from factory to include mounting holes for a rotisserie (sold separately). Do not
use a rotisserie not specifically manufactured for this grill.
Read and follow all instructions provided with the rotisserie. Save instructions for future reference.
Do not use the side burner when using a rotisserie.
WARNING
•
When using an AC current rotisserie, it must be electrically grounded in accordance with local
codes, or in the absence of local codes:
•
In the US: The National Electrical Code – ANSI-NFPA No. 70 – Latest Edition
•
In Canada: the Canadian Electrical Code – CSA C22.1
•
The Rotisserie is equipped with a three pronged plug for your protection against electrical
shock. This plug should be plugged directly into a properly grounded 3 prong receptacle. Never
cut or remove the grounding plug. Any extension cord must also have a 3 prong receptacle.
•
All electrical supply cords should be kept away from water and any hot surfaces of the grill.
TURNING OFF THE GRILL:
1.
Turn off the cylinder valve.
2. Turn all burner control knobs to the “OFF” position.
Note:
Turn off LP cylinder first to prevent gas from being left in the system under pressure.
CAUTION:
•
The cylinder valve should always be in the off,
or closed, position when the grill is not in use.
To turn off the cylinder valve,
turn knob clockwise until it stops.
USING OTHER FEATURES OF THE GRILL:
WARNING
•
•
•
•
•
•
Read instructions on lighting your grill to light the side burner.
Never close the side burner cover when the burner is lit.
Use a 10” diameter pot or smaller that does NOT have an extended handle when cooking on the
side burner. Center pot over burner.
Never place more than 15 pounds on the side burner. The side burner is not constructed to hold
weight exceeding 15 pounds.
Use caution to avoid bumping grill, side burner or pot to prevent pot from spilling contents
possibly leading to severe burns.
DO NOT use side burner to deep fry food in oil to avoid dangers associated with oil igniting
creating a very dangerous situation.
THE SEAR BURNER:
•
The sear burner is ideal for steaks to sear the outside of the meat and seal in the juices.
LIGHTS:
•
Simply push the button on the control panel labeled “LlGHTS” to activate built-in LEDs to see controls at
night.
12
PROPER CARE & MAINTENANCE:
WARNING:
If a bristle brush is used to clean any of the cooking surfaces, ensure no loose bristles remain
on the cooking surfaces prior to grilling as loose bristles may attach to food.
CLEANING INTERIOR OF GRILL:
•
We recommend cleaning off food residue immediately after cooking by gently scrubbing grates with wire bristle
brush and then turning burners to HIGH for approximately 5 minutes.
WARNING: DO NOT leave grill unattended when grill is on. Wear oven mitts to protect from burns.
• The heat from the burners will burn off most food/grease residue from grates & heat tents and turn it to an ash like
substance which will fall to the bottom of the firebox or grease tray. After the grill cools (approximately 30 minutes)
remove grates and heat tents and brush the ash and any grease out of the firebox. Clean and replace grease cup.
Inspect the heat tents for damage or deterioration before reinstalling in the grill. (Replacements can be ordered by
calling 800-527-0717.)
• Wash the grates and heat tents with a mild detergent and rinse with hot water periodically if desired.
CAUTION: DO NOT allow ash residue to remain on the grease tray or firebox as it could block proper grease
drainage of the grill.
INTERIOR OF GRILL LID:
•
Smoke will accumulate inside grill lid and may flake onto your food. Clean the inside of the grill lid with scrub brush
and baking soda/water solution. Dry thoroughly. Do not mistake this for paint. The interior of gas grill lids are not
painted.
MAINTAINING EXTERIOR OF GRILL:
•
•
•
•
•
To protect your grill from excessive rust, the unit must be kept clean and covered at all times when not in use.
Painted surfaces. Wash with mild detergent or non-abrasive cleaner and warm soapy water.
Stainless steel surfaces. To maintain your grill’s appearance, wash with mild detergent and warm soapy water and
wipe dry with a soft cloth after each use. Baked-on grease deposits may require the use of an abrasive plastic
cleaning pad. Use only in direction of brushed finish to avoid damage. Do not use abrasive pad on areas with
graphics. Car wax may help protect the exterior finish of your grill.
Porcelain surfaces. Because of glass-like composition, most residue can be wiped away with a solution of baking
soda and water or specially formulated cleaner. Use non-abrasive scouring powder such as baking soda for
stubborn stains.
Plastic and rubber parts. Wash with warm soapy water and wipe dry. Do not use citrisol, abrasive cleaners,
degreasers or a concentrated grill cleaner on plastic parts. Damage to and failure of parts can result.
RUST:
•
•
•
Discoloration, rust and rust pits can occur as a result of high cooking temperatures, acidic marinades, grease fires
and exposure to coastal climates or other natural elements.
Rust spots on the interior surface can be buffed, cleaned, then lightly coated with vegetable oil or vegetable oil spray
to minimize rusting.
Never use cleaners containing chlorine or store swimming pool supplies or chemicals in cart compartment as
chlorine promotes rust.
BURNER CLEANING AND MAINTENANCE:
•
•
•
Keep the appliance free and clear of combustible materials, gasoline and other flammable vapors and liquids.
Keep the ventilation openings of the cylinder enclosure free and clear of debris.
Visually check burner flames for proper operation (see pictorial in “Burner Assembly/Maintenance” under Proper Care
and Maintenance). Spiders or other insects can nest in the burner causing gas blockage.
• For safe grilling and peak performance of your grill, perform these checks at least twice per year or after extended
periods of storage.
• Be sure to tighten up all hardware (nuts, bolts, screws, etc.) at least twice per year.
CAUTION: Some parts may contain sharp edges. Wear protective gloves if necessary.
• Remove the cooking grills, heat distribution plates, and burners from inside your grill. Use a brush with hot water
and detergent to remove excess residue. NEVER use a commercial oven cleaner. Rinse completely with water.
Towel dry and replace all components as described in the assembly instructions.
13
BURNER ASSEMBLY/MAINTENANCE:
•
Although your burners are constructed of stainless steel,
they may corrode as a result of the extreme heat and acids
from cooking foods. Regularly inspect the burners for cracks,
abnormal holes, and other signs of corrosion damage. If found,
replace the burner.
•
DO NOT block ventilation areas in sides, back or cart
compartment of grill. Burner tubes can become blocked by
spiders and other insects building their nests. Blocked burner
tubes can prevent gas flow to the burners and could result in
a burner tube fire or fire beneath the grill. To clean the Burner
Assembly follow these instructions to clean and/or replace parts
of burner assembly or if you have trouble igniting the grill.
1.
Turn gas off at control knobs and LP cylinder tank valve.
Debris
Bolt
2. Remove cooking grills and heat distribution plates.
3. Remove bolt from each burner “foot” using a screwdriver.
4. Carefully lift each crossover channel up and away from burners.
5. Carefully lift each burner up and away from valve openings.
Crossover Channel
6. Use a narrow bottle brush or a stiff wire bent into a small hook
to run through each burner tube or use compressed air to blow
into burner tube and out the flame ports. Check each port to
make sure air comes out each hole.
CAUTION: Wear eye protection when using compressed air.
7.
Use a wire brush to clean the entire outer surface of burner to
remove food residue and dirt.
Valve Nozzle
8. Check burner for damage, if any cracks or holes are
found replace burner.
9. Install burner in grill and carefully align crossover channels
between burners and orient burners CORRECTLY.
IMPORTANT: Burner opening must slide over valve nozzle.
Burner Opening
10. Replace bolts and nuts to each burner and crossover channel.
Note:
Follow the “Gas Leak Testing” section of this
manual. Relight burners to verify proper operation.
11. Replace heat distribution plates and cooking grills.
PROPER VALVE TO BURNER ALIGNMENT
14
BURNER ADJUSTMENT:
WARNING
•
DO NOT attempt to adjust burner air shutter until grill has cooled down for approximately 30
minutes. Failure to do so could cause severe burns.
•
Normal flame should be soft blue with yellow tips between 1 in. - 2 in. when burner is on “HIGH”.
Depending on elevation, burner air shutter may need to be adjusted to obtain correct air to fuel ratio.
CORRECT
INCORRECT
Soft blue flame with yellow tips
•
Wavy with yellow flames
To adjust air shutter, loosen set screw and rotate air shutter to desired position to achieve normal
flame. Tighten set screw after adjustment is made. Relight the grill to observe flame. Incremental
adjustments may be needed to achieve a good flame.
Set Screw
TRANSPORTING AND STORAGE:
WARNING
•
•
•
•
•
•
•
•
Never move a grill when hot or in use.
Make sure that cylinder valve is closed and burner knobs are in the off position.
DO NOT store a spare LP gas cylinder (filled or empty) under or near the grill.
Never store flammable liquids or spray canisters under or near the grill.
If the outdoor cooking gas appliance is not in use, the gas must be turned off at the LP gas
supply cylinder.
Storage of an outdoor cooking gas appliance indoors is permissible only if the cylinder is
disconnected and removed from the outdoor cooking gas appliance.
Cylinders must not be stored in a building or enclosure, including garages and sheds.
Cylinders must be kept out of reach of children.
BEFORE STORING YOUR GRILL:
•
•
•
•
•
•
15
Ensure that the cylinder valve is fully closed.
Clean all surfaces. Lightly coat the burners with cooking oil to prevent excess rusting.
If storing the grill indoors, disconnect the LP tank and leave the LP tank OUTDOORS.
Place a protective cap cover on the LP tank and store the tank outdoors in a well ventilated area out of direct sunlight.
Check and clean burner prior to use after storing, at the beginning of grilling season or after a period of not being
used. Spiders and insects like to build nests in burner tubes (especially during colder months). Blocked burner
tubes can prevent gas flow to the burners and could result in a burner tube fire or fire beneath the grill. See “Burner
Assembly/Maintenance” under Proper Care and Maintenance.
If storing the grill outdoors, cover the grill with a grill cover for protection from the weather.
TROUBLE SHOOTING:
To see trouble shooting or assembly videos, visit us at:
Problem
Possible Cause
Prevention/Cure
Burner will not light
LP gas tank valve is closed
Make sure regulator is securely attached to the LP gas tank, turn LP
gas tank valve to “OPEN”
LP gas tank is low or empty
Check if LP gas tank is empty. If empty, replace or refill.
LP gas leak
1. Turn LP gas tank valve to “CLOSED”
2. Wait 5 minutes for gas to clear
3. Follow “Leak Testing” in the owner’s manual
Coupling nut and regulator not fully connected
See section on “Connecting Hose and Regulator”
Obstruction of gas flow
1. Clean burner assembly
2. Check for bent or kinked hose
Burner may not be properly seated
Reseat burner and valve. Refer to “Burner Assembly/Maintenance”
instructions
Spider webs or insect nest in venturi
Clean venturi and burner assembly
Burner ports clogged or blocked
Clean burner ports
Battery needs to be changed
Replace the battery (follow assembly step for inserting battery)
Wires or electrode covered with cooking residue
Clean wire and/or electrode with rubbing alcohol
Electrode and burners are wet
Wipe dry with cloth
Electrode cracked or broken - sparks at crack
Replace electrode
Wire loose or disconnected
Reconnect wire or replace electrode/wire assembly
Wire is shorting (sparking) between ignitor and
electrode
Replace ignitor wire/electrode assembly
Bad ignitor
Replace ignitor
Out of gas
Replace or refill LP gas tank
Flow limiting device may have been activated
1. Mini Reset:
a. Turn control knobs and LP gas tank valve to “OFF”
b. Wait one minute and relight grill per “Lighting Instructions”
2. If flames are still too low, perform a Full Reset
Full Reset:
a. Turn control knobs and LP gas tank valve to “OFF”
b. Disconnect regulator from propane tank
c. Inspect LP cylinder rubber seal
d. Wait 1 minute
e. Reconnect regulator and perform “Leak Testing” on all
connections.
f. Light grill per “Lighting Instructions”
Irregular flame pattern.
Flame does not run full
length of burner
Burner ports are clogged or blacked
Clean burner ports
Air shutter on burner needs adjustment
See section on “Burner Adjustment”
Flame is yellow or orange
New burner may have residual manufacturing
oils
Burn grill for 15 minutes on “HIGH” with the lid closed
Spider webs or insect nest in venturi
Clean venturi and burner assembly
Food residue, grease, etc.
Clean burner assembly
Poor alignment of valve to burner venturi
Make sure burner venturi is properly engaged with valve
Air shutter on burner needs adjustment
See section on “Burner Adjustment”
Grill does not get hot
enough
16
Problem
Possible Cause
Prevention/Cure
Flame blows out
High or gusting winds
Do not use grill in high winds
Low on LP gas
Replace or refill LP gas tank
Burner holes may be obstructed
Refer to “Burner Assembly/Maintenance” instructions
Flow limiting device tripped
Refer to “Regulator Resetting Procedure”
Grease buildup
Clean all grill parts per “Proper Care and Maintenance” instructions
Excess fat in meat
Trim fat from meat before grilling
Excessive cooking temperature
Adjust (lower) cooking temperature
Grease fire
Grease trapped by food buildup around burner
system
1. Turn control knobs and LP gas tank valve to “OFF”
2. Leave lid in open or closed position and let fire burn out. Use BC
type fire extinguisher or baking soda, sand or dirt to smother fire,
if necessary.
3. After grill cools, remove and clean all parts per “Proper Care and
Maintenance” instructions
Flashback (fire in burner
tubes) / knobs melting
Burner and/or burner tubes are blocked
Clean burners and/or burner assembly
Inside of lid is peeling
(like paint peeling)
Baked on grease buildup has turned into carbon
and is flaking off
Clean thoroughly per “Proper Care and Maintenance” instructions
Flare-up
GRILL COOKING TIPS:
CLEANLINESS:
•
•
•
•
Always wash hands thoroughly with soap and hot water prior to handling food and after handling raw
meat, uncooked poultry or seafood.
When using a platter to carry raw meat, uncooked poultry or seafood to the grill, make sure to wash
the platter thoroughly with soap and hot water before placing cooked foods back on the platter or use
different platters for raw and cooked foods.
Never use the same utensils when handling raw meat, uncooked poultry or seafood unless you wash
the utensils thoroughly with soap and hot water.
Never re-use marinade from raw meat or uncooked poultry on foods that have been cooked and are
ready to be served.
GRILLING TO PROPER TEMPERATURE:
•
•
Use a meat thermometer to be sure food has reached a safe internal temperature.
The USDA recommends the minimum temperature be reached for the following food items:
Chops . . . . . . . . . . . . . . . . . . . 145° F (62.8° C)
Roasts . . . . . . . . . . . . . . . . . . . 145° F (62.8° C)
Ground Meat . . . . . . . . . . . . . . 160° F (71° C)
Seafood . . . . . . . . . . . . . . . . . . 145° F (60° C)
Pork . . . . . . . . . . . . . . . . . . . . . 145° F (62.8° C)
Vegetables . . . . . . . . . . . . . . . . 145° F (62.8° C)
Poultry . . . . . . . . . . . . . . . . . . . 165° F (82° C)
HELPFUL HINTS:
•
•
•
•
17
If you pre-cook meat or poultry, do so immediately before grilling.
Never defrost meat at room temperature or on a countertop.
Refrigerate leftovers within 2 hours of taking food off the grill.
For additional information, please phone the USDA’s toll free Meat & Poultry Hotline at 800-535-4555.
ASSEMBLY INSTRUCTIONS:
Make sure you have all items listed under PARTS LIST and PARTS BAG CONTENTS before
you begin the installation process.
PARTS BAG CONTAINS:
Qty.
8
17
4
2
2
8
1
Qty.
1 Locking Nut
2 M6 Washers
3 Hinge Pins
3 Cotter Pins
3 AA/1.5V Alkaline Batteries
1 Caster Tightening Pin
M6 X 12 mm Bolts (Black)
M6 X 12 mm Bolts (Silver)
M6 X 30 mm Bolts (Silver)
M5 X 12 mm Bolts (Black)
M4 X 12 mm Bolts (Black)
M4 X 12 mm Bolts (SIlver)
Shoulder Bolt (Black)
M6 X 12 mm Bolts (Silver)
M6 X 12 mm Bolts (Black)
M4 X 12 mm Bolts (SIlver)
M6 Washers
Hinge Pins (Short)
Caster Tightening Pin
M4 X 12 mm Bolts (Black)
Cotter Pins
AA/1.5V Alkaline Batteries
M5 X 12 mm Bolt (Black)
M6 X 30 mm Bolt (Silver)
Shoulder Bolt
Locking Nut
18
READ ALL SAFETY WARNINGS & ASSEMBLY INSTRUCTIONS CAREFULLY
BEFORE ASSEMBLING OR OPERATING YOUR GRILL.
WE RECOMMEND TWO PEOPLE WORK TOGETHER WHEN ASSEMBLING THIS UNIT.
The following tools are required to assemble this Brinkmann Heavy-Duty Gas Grill:
• Screwdriver
• Hex Nut Wrench
PARTS LIST:
1
1
Grill Body Assembly
2
1
Left Side Table Assembly
3
1
Right Side Table Assembly
4
1
Warming Rack
5
3
Cooking Grills
6
5
Heat Tents
7
1
Sear Burner Bezel
8
1
Sear Burner Knob
9
1
Sear Burner Grate
10 1
Left Panel
11 1
Right Panel
12 1
Left Door
13 1
Upper Cart Brace
14 1
Right Door
15 1
Back Panel
16
17
18
19
20
21
22
23
24
25
26
27
28
1
1
1
1
1
1
1
1
1
2
2
1
1
Grease Tray
Cart Base
Lower Cart Brace
Door Stopper
Tank Holder
Tank Gauge Bracket With Spring
Tank Gauge Needle Assembly
Tank Heat Shield
Wind Deflector
Locking Swivel Casters
Swivel Casters
Sear Burner Grease Tray
Grease Cup
This grill is designed with Dual Fuel Valves to easily
convert from LP (propane) gas to natural gas.
A Brinkmann conversion kit must be purchased
and installed for use with natural gas.
To see trouble shooting or assembly videos, visit us at:
19
1
2
3
7
8
4
9
5
11
10
6
13
12
14
15
17
21
22
16
19
18
20
23
24
25
26
27
28
FOR COVERS, ACCESSORIES AND OTHER PRODUCTS, PLEASE VISIT US ONLINE AT:
(Proof of purchase will be required.)
Inspect contents of the box to ensure all parts are included and undamaged.
20
Choose a good, cleared assembly
area and get a friend to help you put
your grill together. Lay
cardboard down to protect grill finish
and assembly area.
CAUTION:
Some parts may
contain sharp edges.
Wear protective gloves
if necessary.
Step 1
Lower Cart Brace
Turn cart base upside down, use
two M6 X 12 mm bolts (silver) to
attach the lower cart brace.
Note: The edge of the lower cart
brace should be locked on
the brackets.
Step 2
Attach the two swivel casters and
the two locking swivel casters to
the cart base, as shown.
Locking Swivel Casters
Back
Swivel Casters
Front
Caster Tightening Pin
Note: Insert the caster
tightening pin in each
caster so caster can be
tightened.
21
Figure 1
Tank Gauge Bracket
Step 3
Remove the spring, washer, and
bolt from the tank gauge bracket.
Set aside for use in Step 5. Attach
the tank gauge bracket onto the
base using two M6 X 12 mm bolts
(sliver) as illustrated in Figure 1.
Figure 2
Cotter Pin
Tank Gauge
Needle Assembly
Bolt
Washer
Hinge Pin
Spring
Door Stopper
Tank Gauge Bracket
Attach the tank gauge needle
assembly to the base and the
bracket and secure with a hinge
pin and a cotter pin as illustrated in
Figure 2.
Front
Step 4
Back
Hinge Pin
Turn cart base right side up, use
two M6 X 12 mm bolts (silver) to
attach the door stopper to the base,
as shown.
Figure 1
Step 5
Cotter Pin
Tank Holder
Figure 2
Figure 3
Bolt
Washer
Shoulder Bolt
Locking Nut
Tank Holder
Spring
Post
Use two hinge pins and two cotter
pins, to secure the tank holder to the
tank holder fixed stands as shown.
(Figure 1)
Slide the spring, from Step 3 onto
the tank gauge bracket post. Then
align the tank holder with the post
and secure with the washer and bolt
from Step 3. (Figure 2) Attach the
tank gauge needle assembly to the
tank holder using the shoulder bolt
and the locking nut. (Figure 3)
Tank Gauge
Needle Assembly
22
Right Panel
Left Panel
Step 6
Using four M6 X12 mm bolts (silver)
attach the left panel and the right
panel to the cart base.
Step 7
Using four M6 X 12 mm bolts
(silver) attach the back panel.
Back Panel
23
M6 X 12 mm
M6 X 30 mm
Upper Cart Base
Step 8
To attach the wind deflector, insert
the upper cart brace pre-attached
bolts through the key holes of
the wind deflector, slide the wind
deflector downward and tighten the
bolts securely. See Figure 1 and 2
below.
Wind Deflector
Figure 1
Figure 2
Use four M6 X 30 mm bolts (silver)
and two M6 X 12 mm bolts (silver)
to attach the upper cart brace to left
and right panels.
Step 9
Attach the left and right doors using
eight M4 X 12 mm bolts (silver).
24
Grill Body Assembly
Step 10
With the help of a friend, place the
grill body assembly on the grill cart.
Secure using four M6 X 12 mm bolts
(black) from the left and the right
side of the frame.
Fixed Stands
Left Side Table Assembly
Step 11
To attach the left side table
assembly, first insert the side table’s
fixed stands onto the grill body
hooks (Figure 1).
Open the grill hood, then use one
M5 X 12 mm bolt (black) and one
M6 washer to secure the left side
table assembly to the grill body from
the inside (Figure 2).
Hook
Fixed Stands
Figure 1
Use two M6 X 12 mm (black) bolts
to secure the side table base
(Figure 3).
M5 X 12 mm
Hooks
Figure 3
25
Figure 2
Figure 1
Figure 2
Step 12
Right Side Table Assembly
To attach the right side table
assembly, first insert the side table’s
fixed stands onto the grill body hooks
(Figure 1).
M5 X 12 mm
Figure 3
Open the grill hood, then use one
M5 X 12 mm bolts (black) and one
M6 washer to secure the right side
table assembly to the grill body from
the inside (Figure 2).
Use two M6 X 12 mm (black) bolts
and one M6 X 12 mm (silver) bolt to
secure the side table base
(Figure 3).
Silver Bolt
Figure 1
Step 13
Remove the two M4 X 10 mm bolts
and spring washers from the sear
burner valve.
Hole
Sear Burner Valve
Insert the sear burner valve
assembly through the hole in the
side burner table base (Figure 1).
Figure 2
Place the bezel over the control
knob mounting stem and position
over holes in side burner table base
and sear burner valve assembly.
Attach with two M4 X 10 mm, bolts
that came with valve.
Then install the sear burner knob
onto valve stem (Figure 2).
Sear Burner Knob
Bezel
Pin on Bottom
26
Step 14
Remove the retaining nut from the
top of the thermocouple, and insert
the thermocouple into the hole in
the sear burner as shown. Reattach
nut on the other side and tighten.
Thermocouple
Sear Burner
Igniter Lead
Remove the pre-attached screws
from the sear burner. Use the
screws to connect the sear burner
orifice bracket as shown and
tighten with a screwdriver.
Connect the sear burner igniter
lead wire to the electrode on the
sear burner as shown.
Attach sear burner LED light wire to
the LED light lead coming from grill
body. Be sure to align white wires
with each other and black wires
with each other.
Retaining nut
Thermocouple
Black
Wire
Sear Burner
Orifice Bracket
White
Wire
Black
Wire
White
Wire
LED Light
Lead
Screws
Step 15
Remove igniter cap and insert
a battery with the end of battery
toward igniter cap.
Figure 1
Ensure spring is in place inside
igniter cap. Replace igniter cap and
make sure the igniter is working
properly (Figure 1).
Igniter Cap
+
Place two batteries into the LED
light battery compartment, and slide
compartment into the sleeve on the
inside left panel. (Figure 2)
-
-
+
+
-
Figure 2
Sleeve
27
LED Battery
Compartment
Battery
Sear Burner Grate
Step 16
Slide open the right side table,
insert the sear burner grate.
Open
Warming Rack
Cooking Grills
Step 17
Place the heat tents on lower level
of grill body assembly directly
above burners.
Heat Tents
Step 18
Place cooking grills on support ribs
directly above heat tents.
Step 19
Place warming rack in brackets so
that it sits above the cooking grills.
Warming Rack
Brackets
Heat Tents
Brackets
28
Step 20
Insert the sear Burner grease tray
on the tracks under sear burner in
back.
Sear Burner
Grease Tray
Step 21
Attach the tank heat shield under
the grease tray using two
M4 X 12 mm bolts (black)
(Figure 1).
Figure 1
Grease Tray
Slide the grease tray onto the tracks
located behind and underneath the
grill body assembly. (Figure 2).
Tank Heat Shield
Figure 2
Grease Tray
29
Step 22
Hang grease cup from the grease
tray. Make sure to slide cup onto
tracks as illustrated.
Grease Cup
Brinkmann® 4580 (Assembled)
300
200
100
Read Instructions
Before Lighting:
Lea las Instrucciones
Antes de Iluminación:
1. Open lid during lighting.
1. Abra la tapa durante el
encendimiento.
2. Select a burner to be lit. Push
and turn control knob of that
burner to “HIGH.” Press
electronic igniter and hold for
3-5 seconds.
3. If ignition does not occur in
5 seconds, turn control knob
to “OFF,” wait 5 minutes and
repeat lighting procedure.
400
500
600
SEAR BURNER
HORNILLA PARA
DORAR
FOR OUTDOOR
USE ONLY
SOLAMENTE PARA
USO EN EXTERIORES
2. Seleccione la hornilla que va a
encender. Empuje y gire la
perilla de control de esa
hornilla a la posición “ALTO”.
Oprima el encendedor
electrónico
y manténgalo oprimido
3 a 5 segundos.
4. Continue to push in control knob for 30 seconds after sear burner is lit.
1. Abra la tapa durante el encendimiento.
MAXIMUM SEAR BURNER
WEIGHT = 15 lbs.
PESO MÁXIMO DE LA HORNILLA
PARA DORAR = 6.8 kg
800-527-0717
For Accessories, Parts or Assistance, Call
or Visit our Website
Para Accesorios, Partes o Asistencia,
Llame o Visite Nuestro Sitio de Internet
3. Press electronic igniter and hold for 3 to 5 seconds.
Instrucciones de Iluminación para la Hornilla
para Dorar:
Escanear con un
Teléfono Inteligente
para Más Información
NG Conversion
Kit Required
Kit de la Conversión
del NG Requerido
1. Open lid during lighting.
2. Push and turn control knob to “HIGH” and continue to push in.
5. If ignition does not occur in 5 seconds, turn control knob to “OFF,” wait 5
minutes and repeat lighting procedure.
Scan with a Smart Phone
for More Information
3. Si la hornilla NO se enciende
en 5 segundos, gire la perilla
de control a la posición
"APAGADO"espere 5 minutos y
repita el procedimiento de
encendido.
LIGHTS
LUCES
Sear Burner Lighting Instructions:
2. Empuje la perilla de control y gire a la posición “ALTO” y continúe
empujando hacia adentro.
3. Presione el encendedor electrónico y sosténgase por 3 a 5 segundos.
4. Continúe empujando la perilla de control hacia adentro por
30 segundos después de que la hornilla para dorar se enciende.
5. Si la hornilla NO se enciende en 5 segundos, gire la perilla de control a la
posición "APAGADO", espere 5 minutos y repita el procedimiento de
encendido.
ELECTRONIC
IGNITER
ENCENDEDOR
ELECTRÓNICO
30
FOR COVERS, ACCESSORIES AND OTHER PRODUCTS, PLEASE VISIT US ONLINE AT:
PARA CUBIERTAS, ACCESORIOS Y OTROS PRODUCTOS, FAVOR DE VISITARNOS POR LA RED MUNDIAL EN:
WARRANTY
The Brinkmann Corporation warrants to the original purchaser that the Brinkmann Heavy-Duty Gas Grill is free from defects due to workmanship or materials
for:
Lifetime: on stainless steel tube burners
Three-year: on all other stainless steel parts
One-year: on valves, frame, housing, cart, igniter, cooking grates and other related parts
The Brinkmann Corporation’s obligations under this warranty are limited to the following guidelines:
• This warranty does not cover grills that have been altered/modified or damaged due to: normal wear, rust, abuse, improper maintenance and/or
improper use.
• This warranty does not cover surface scratches, rust or heat damage to the finish, which is considered normal wear.
• The Brinkmann Corporation may elect to repair or replace damaged units covered by the terms of this warranty.
• This warranty extends to the original purchaser only and is not transferable or assignable to subsequent purchasers.
The Brinkmann Corporation requires reasonable proof of purchase. Therefore, we strongly recommend that you retain your sales receipt or invoice. To obtain
replacement parts for your Brinkmann Heavy-Duty Gas Grill under the terms of this warranty, please call Customer Service Department at
800-527-0717. A receipt will be required. The Brinkmann Corporation will not be responsible for any grills forwarded to us without prior
authorization.
EXCEPT AS ABOVE STATED, THE BRINKMANN CORPORATION MAKES NO OTHER EXPRESS WARRANTY.
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN DURATION TO THOSE
LISTED ABOVE FROM THE DATE OF PURCHASE. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY
LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
ANY LIABILITY FOR INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM THE FAILURE OF THE BRINKMANN HEAVYDUTY GAS GRILL TO COMPLY WITH THIS WARRANTY OR ANY IMPLIED WARRANTY IS EXCLUDED. CUSTOMER ACKNOWLEDGES THAT THE
PURCHASE PRICE CHARGED IS BASED UPON THE LIMITATIONS CONTAINED IN THE WARRANTY SET OUT ABOVE. SOME STATES DO NOT
ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY
NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM
STATE TO STATE.
GARANTÍA
The Brinkmann Corporation garantiza al comprador original que la parrilla Brinkmann Heavy-Duty Gas Grill está libre de defectos de materiales o mano
de obra:
De por vida: los quemadores de acero inoxidable de tubo
Tres-años: en todas las piezas de acero inoxidable restantes
Un-año: en válvulas, armazón, envoltura, carro, encendedor, rejillas de cocinar y piezas relacionadas
Las obligaciones de The Brinkmann Corporation con respecto a esta garantía se limitan a lo siguiente:
•
Esta garantía no cubre parrillas que hayan sido alteradas/modificado o dañadas debido a: uso normal, herrumbre, maltrato, mantenimiento inadecuado
y/o uso inapropiado.
•
Esta garantía no cubre rayones superficiales, daño por herrumbre o por calor al acabado, lo cual se considera como uso normal.
•
The Brinkmann Corporation puede decidir reparar o reemplazar las unidades dañadas cubiertas bajo los términos de esta garantía.
•
Esta garantía se otorga al comprador original únicamente y no es transferible o asignable a los compradores posteriores.
The Brinkmann Corporation exige un comprobante de compra razonable. Por lo tanto, le recomendamos enfáticamente que retenga su recibo o factura
de venta. Para obtener partes de repuesto para la parrilla Brinkmann Heavy-Duty Gas Grill bajo los términos de esta garantía, sírvase contactar al
Departamento de Servicio al Cliente al 800-527-0717. Se exigirá la presentación de un recibo. The Brinkmann Corporation no será responsable de
ninguna parrilla devuelta a nosotros sin autorización previa.
EXCEPTO POR LO INDICADO ARRIBA, THE BRINKMANN CORPORATION NO OTORGA NINGUNA OTRA GARANTÍA EXPRESA.
LAS GARANTÍAS IMPLÍCITAS DE COMERCIABILIDAD Y ADECUACIÓN CON UN FIN EN PARTICULAR SON DE DURACIÓN LIMITADA DE ACUERDO
A LO INDICADO ARRIBA A PARTIR DE LA FECHA DE COMPRA. ALGUNOS ESTADOS NO PERMITEN LIMITACIONES DE DURACIÓN DE UNA
GARANTÍA IMPLÍCITA; POR LO TANTO, LA LIMITACIÓN ANTERIOR PODRÍA NO SER APLICABLE EN SU CASO.
SE EXCLUYE CUALQUIER RESPONSABILIDAD POR DAÑOS INDIRECTOS, INCIDENTALES O CONSIGUIENTES DERIVADOS DE LA FALTA
DE CUMPLIMIENTO DE ESTA GARANTÍA O DE CUALQUIER GARANTÍA IMPLÍCITA DE BRINKMANN HEAVY-DUTY GAS GRILL. EL CLIENTE
RECONOCE QUE EL PRECIO DE COMPRA COBRADO SE BASA EN LAS LIMITACIONES CONTENIDAS EN LA GARANTÍA ANTERIOR. ALGUNOS
ESTADOS NO PERMITEN LA EXCLUSIÓN O LIMITACIÓN DE LOS DAÑOS INCIDENTALES O CONSIGUIENTES; POR LO TANTO, LA LIMITACIÓN O
EXCLUSIÓN ANTERIOR PODRÍA NO SER APLICABLE EN SU CASO. ESTA GARANTÍA LE OTORGA DERECHOS LEGALES ESPECÍFICOS Y USTED
PUEDE TENER ADEMÁS OTROS DERECHOS QUE VARÍAN DE UN ESTADO A OTRO.
140-4580-S
0812
©2012 The Brinkmann Corporation
Dallas, Texas 75244 U.S.A.
Owner’s Manual for Model
Manual del Propietario para el Modelo
810-4580-S
Download PDF

advertising