Brinkmann 810.63450 Gas Grill User Manual

GRAND
6345
GOURMET
Gas Outdoor
Grill
OWNER'S
ASSEMBLY
AND
MANUAL
OPERATING
INSTRUCTIONS
r,V/l±1
;t: I I: [r_
HAZARDOUS EXPLOSION MAY
RESULT IFTHESE WARNINGS AND
INSTRUCTIONS
ARE IGNORED. READ
AND FOLLOW ALL WARNINGS AND
INSTRUCTIONS IN THIS MANUAL TO
AVOID PERSONAL INJURY, INCLUDING
DEATH OR PROPERTY DAMAGE.
IMPORTANT
SAFETY
WARNINGS
WE WANTYOU TO ASSEMBLE
AND USEYOUR GRILL AS SAFELY AS POSSIBLE.
THE PURPOSE OF THIS SAFETY ALERT SYMBOL A, IS TO ATTRACT YOUR
ATTENTION TO POSSIBLE HAZARDS AS YOU ASSEMBLE AND USE YOUR GRILL.
WHEN YOU SEE THE SAFETY ALERT SYMBOL
PAY CLOSE ATTENTION TO THE INFORMATION
WHICH
_,
IF YOU SMELL
READ ALL SAFETY WARNINGS AND INSTRUCTIONS
CAREFULLY
BEFORE ASSEMBLING
AND OPERATING YOUR GRILL.
GAS:
1.
Shut off gas to the appliance.
2.
Extinguish
3.
Open Lid.
4.
If odor continues,
fire department.
,
,
FOLLOWS?
any open flame.
keep away from the appliance
and immediately
call your gas supplier
or your
DO NOT store or use gasoline
other appliance.
or other flammable
liquids or vapors in the vicinity of this or any
An LP cylinder not connected
appliance.
for use shall not be stored in the vicinity of this or any other
DO NOT store a spare LP gas cylinder under or near this appliance.
•
Never fill the cylinder beyond 80% full.
•
A fire causing death or serious injury may occur if the above is not followed
exactly.
TABLE
General Warnings
Installation
OF CONTENTS
..............................................
and LP Cylinder Specifications
Connecting
and Safe Use ..............
LP Cylinder and Hose / Regulator to Grill ................
Leak Testing .................................................
3
4-6
6-7
8-9
Pre-start Check List .............................................
9
Lighting Instructions .........................................
10-11
Operating
12-14
Grill and Helpful Hints ...............................
Proper Care and Maintenance
Transporting
and Storage
Trouble Shooting
Frequently
Asked Questions
Grilling Accessories
_, DANGER:
.......................................
..............................................
Parts List and Assembly
Warranty
................................
14-16
16
17
..................................
18-19
Instructions ............................
20-32
.........................................
Information ....................................
33-34
Back Cover
Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
A'_,WARNING: Be alert to the possibility of serious bodily injury if the instructions are not followed. Be sure to read and
carefully follow all of the messages.
A'L.CAUTION:
Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
2
GENERAL
WARNINGS
Never use natural gas in a unit designed
for liquid propane gas.
•
Never use charcoal
•
Leak test all connections
each tank refill.
•
Never check for leaks using a match or open flame.
£k CAUTION!
briquets or lighter fluid in a gas grill.
before first
use, even if grill was purchased
Strong odors, colds, sinus congestion,
propane. Use caution and common
and after
etc. may prevent the detection
of
sense when testing for leaks.
•
Always keep your gas grill free and clear of gasoline, paint thinner, or other flammable
and liquids or combustible materials.
•
Always check the grill prior to each use as indicated
manual.
•
DO NOT obstruct
•
Never place more than 15 pounds on the side burner. DO NOT lean on the side burner shelf.
•
Keep children and pets away from
hot grill. DO NOT allow children to use or play near this grill.
•
DO NOT leave the grill unattended
while in use.
•
DO NOT allow the gas hose to come in contact with hot surfaces.
•
DO NOT allow grease from drain hole to fall on hose or valve regulator
•
Keep any electrical
•
Keep a fire extinguisher on hand acceptable for use with gas products. Refer to your local
authority to determine proper size and type.
•
For household
•
DO NOT use while under the influence
•
Grill is hot when in use.To avoid burns:
•
•
•
•
•
the flow of combustion
in the "Pre-Start
or ventilation
vapors
Check List" section of this
air.
assembly.
supply cords away from water or heated surfaces.
use only. DO NOT use this grill for anything
other than its intended
purpose.
of drugs or alcohol.
DO NOT attempt to move the grill.
Lock the wheels so the unit does not accidentally move.
Wear protective gloves or oven mitts.
DO NOT touch any hot grill surfaces.
DO NOT wear loose clothing or allow hair to come in contact with grill.
USE
FAILURE
CAUTION
AND
TO ADHERE
COULD
COMMON
TO THE
RESULT
SAVE
3
fully assembled
SAFETY
IN SEVERE
THIS
SENSE
WHEN
WARNINGS
BODILY
MANUAL
FOR
OPERATING
AND
INJURY
FUTURE
YOUR
GUIDELINES
OR PROPERTY
REFERENCE.
GAS
GRILL.
IN THIS
DAMAGE.
MANUAL
FOROUTDOORUSEONLY.DONOToperateindoors or in an enclosedareasuch as a garage,
shed or breezeway.
Useyour grill OUTDOORSin a well ventilatedspaceaway from
prevent dangers associated with gas accumulation
be situated at least 10 feet (3.1 m) from buildings.
dwellings
or other buildings
and toxic vapors. We recommend
to
your grill
Maintain a minimum clearance of 36 inches (91 cm) between all sides of grill and walls or other
combustible material. DO NOT use grill under overhead unprotected combustible construction.
DO NOT use or install this grill in or on a recreational
vehicle and/or boat.
INSTALLATION INFORMATION:
The installation of this appliance must be in accordance with:
All applicable local codes, or in the absence of local codes, either:
•
National Fuel Gas Code ANSI Z223.1 NFPA 54
•
•
•
Natural Gas and Propane Installation Code: CAN/CGA B149.1
Natural Gas Installation Code: CAN/CGA B149.1 (Canada)
Propane Installation Code: CAN/CGA B149.2 (Canada)
To check your local codes, see your local LP gas dealer or natural gas company. This grill was not
intended to be connected to a natural gas supply line. If an external electrical source is utilized, it
must be electrically grounded in accordance with local codes, or in the absence of local codes, with
the National Electrical Code, ANSI/NFPA 70, or the Canadian Electrical Code, CSA 22.1.
LP GAS CYLINDER
(NOT SUPPLIED WITH THIS GRILL)
The LP cylinder is available for purchase at the same location the grill was purchased.
The LP (Liquid Propane) gas cylinder specifically designed to be used with this grill must have
a 20 lb. (9.1 kg) capacity incorporating a Type 1 cylinder valve and an over-filling protection
device (OPD).
•
DO NOT connect this grill to an existing #510 POL cylinder valve with Left Hand threads. The
Type 1 valve can be identified with the large external threads on the valve outlet.
•
DO NOT connect to a propane cylinder exceeding
•
DO NOT connect to a cylinder
this capacity.
that uses any other type of valve connection
device.
4
CYLINDER SPECIFICATIONS:
When purchasing or exchanging a cylinder for your gas grill, it must be constructed and marked in
accordance with the specifications for LP gas cylinders of the U.S. Department of Transportation
(DOT) or the National Standard of Canada, CAN/CSA-B339
Cylinders, Spheres and Tubes for
Transportation of Dangerous Goods; and Commission, as applicable; and provided with a listed
over-filling prevention device (OPD), and provided with a cylinder connection device compatible with
the connection for outdoor cooking appliances.
The cylinder must also be equipped
with:
•
A shut-off valve terminating
in a Type 1 gas cylinder valve outlet.
•
A Type 1 valve that prevents gas flow until a positive seal is obtained.
•
An arrangement
•
A collar to protect the cylinder shut-off valve.
•
A safety relief device having direct communication
•
A listed over-filling
for vapor withdrawal.
prevention
with the vapor space of the cylinder.
device (OPD).
Turn off the cylinder valve when your grill is not in use.
•
Handle the tank with care.
•
Always secure the cylinder
•
Never connect an unregulated
•
DO NOT expose LP gas cylinders
•
DO NOT store a spare LP gas cylinder
•
Allow only qualified
•
DO NOT allow the cylinder to be filled
•
Read and follow
product.
in an upright position.
LP gas cylinder to your grill.
to excessive
heat or ignition sources.
under or near your grill.
LP gas dealers to fill or repair your LP gas cylinder.
all warnings
beyond 80% capacity.
and instructions
that are on the cylinder and that accompany
this
Never store a spare LP gas cylinder under or near your grill.This could cause excess pressure
to be expelled through the vapor relief valve resulting in fire, explosion, or severe personal
injury including death.
NOTE:
PROPANE GAS IS HEAVIER THAN AIR AND WILL COLLECT
PROPER VENTILATION
IS EXTREMELY IMPORTANT.
Keep the ventilation opening(s)
obstructions and debris.
of the LP gas cylinder
enclosure
IN LOW AREAS.
free and clear from
DO NOT insert any foreign objects into the valve outlet. Damage to the back-check could
result. A damaged back-check can cause a leak, possibly resulting in explosion, fire, severe
bodily harm, or death.
FILLING THE LP GAS CYLINDER:
•
Allow only qualified
LP gas dealers to properly fill or repair your LP gas cylinder.
•
New tanks should be purged prior to filling;
•
DO NOT allow the cylinder to be filled beyond 80% capacity. Over-filled tanks can create a
dangerous condition. Over-filled tanks can build-up pressure and cause the relief valve to expel
propane gas vapors. The vapor is combustible and if it comes in contact with a spark source or
flame an explosion causing severe burns, bodily harm, or death could occur.
•
Always use a protective
•
If you exchange a cylinder with a qualified exchange program, be sure the cylinder has
a Type 1 valve and an over-filling prevention device (OPD).
cylinder
inform LP gas dealer if you are using a new tank.
cap when grill is not connected
to cylinder.
INSTALLING THE LP GAS CYLINDER ONTO THE GRILL:
1.
.
.
.
5.
Check that the cylinder valve is closed by turning the knob
clockwise.
Place the cylinder
of cabinet.
into the tank holder in the bottom
Orient the cylinder such that the valve opening faces the
side burner, and so that the hose is not kinked or damaged.
Fully tighten the cylinder clamp underneath
secure tank.
tank holder to
=9
Attach or detach regulator to the LP gas cylinder only
when cylinder is at rest in tank holder.
HOSE AND REGULATOR:
Your grill is equipped with a Type 1 connection
the following features:
1.
device with
The system will not allow gas flow from the cylinder until
a positive connection to the valve has been made.
NOTE: The cylinder valve must be turned off before any
connection is made or removed.
.
.
Cylinder Clamp
A thermal device that will shut off the gas flow if the device is
subject to temperatures above 240°F to 300°F (115°C to
150°C). If this should happen, remove the entire regulator
assembly and dispose of properly. A replacement regulator
assembly can be purchased by contacting customer service
at 800-527-0717. The cause of the excessive heat should be
determined and corrected before using your grill again.
A regulator flow limiting device, when activated, restricts the
flow of gas to 10 cubic feet per hour. If the flow limiting device
is activated, perform Regulator Resetting Procedure.
REGULATOR RESETTING PROCEDURE
1.
Turn burner control knobs to "OFF", turn off the cylinder valve and disconnect
tank. Wait approximately two minutes.
2.
Reattach regulator
regulator from LP gas
and slowly turn cylinder valve back on. The flow limiting device will now be reset.
6
Never use your grill without leak testing all gas connections
"Leak Testing" in this manual for proper procedures.
The pressure
regulator and hose assembly
supplied
and hoses. See the section on
with your gas grill must be used.
•
DO NOT attempt to connect
•
DO NOT use any other pressure regulator/hose assembly other than the one supplied with your grill.
Replacement pressure regulator/hose assembly must be part No 155-2400-0, which can be obtained
by contacting customer service at 800-527-0717.
•
DO NOT attempt to adjust or repair the regulator. The regulator is designed
maximum output pressure of 11 inches of water column (2.74 kPa).
During assembly
damage.
it to any other fuel supply source such as a natural gas line.
and/or replacement
of the gas cylinder,
to operate at a
keep the gas supply hose free of kinks and/or
Visually inspect the hose assembly prior to each use for evidence of damage, excess wear, or
deterioration. If found, replace the assembly before using your grill. Only the manufacturer's
supplied
replacement should be used.
CONNECTING HOSE AND REGULATOR TO AN LP GAS CYLINDER
Ensure the tank valve is CLOSED prior to connecting the LP gas cylinder to your grill.Turn the
valve knob clockwise to properly close the valve. Read and follow all instructions and warnings
on the supply hose safety tags. Read and follow all warnings in this manual concerning the safe
use of LP gas cylinders and the hose and regulator
follow all warnings on the LP cylinder.
before connecting
cylinder to grill. Read and
CONNECTING HOSE AND REGULATOR
1. Check that the cylinder valve is closed by turning the knob clockwise.
2. Check that the grill's burner control knobs are in the "OFF" positions.
3.
Remove the protective
4.
Hold regulator and insert the nipple of connection
the device is centered properly.
5.
Turn the large coupling nut clockwise by hand and tighten to a full stop. Take care not to cross thread
the coupling nut onto the cylinder valve. Do not over-tighten the knob onto the valve. Do not use tools
to tighten connection.
NOTE:
plastic cap from the cylinder valve and the connection
If you are unable to make the connection,
device.
device into the LP cylinder valve outlet. Ensure that
repeat Steps 4 and 5.
6.
Check that the hose does not contain kinks, does not contact sharp edges, and does not contact
surfaces that may become hot during use.
7.
Leak check all fittings before lighting your grill. See section on "Leak Testing"
in this manual.
LEAK TESTING:
To prevent fire or explosion
hazard:
•
DO NOT smoke or permit ignition sources
in the area while conducting
•
Perform test OUTDOORS
•
Never perform a leak test with a match or open flame.
•
Never perform a leak test while the grill is in use or while grill is still hot.
only in a well ventilated
a leak test.
area.
WHEN TO PERFORM A LEAKTEST:
After assembling
your grill and before lighting for the first time, even if purchased
•
Every time the LP gas cylinder
is refilled or if any of the gas components
•
Any time your grill has been moved.
•
At least once per year or if your grill has not been used for more than 60 days.
fully assembled.
are replaced.
CHECKING FOR LEAKS:
1.
Create a mixture of 50% water and 50% liquid dishwashing
2.
Open the lid.
3.
Ensure all control knobs are set to the "OFF" position.
4.
Turn on the fuel supply at the cylinder valve. Turn the
cylinder valve knob one turn counter-clockwise.
5.
Apply the soap water mixture to the following:
soap.
Watch For Bubbles
O
(_
Supply tank (cylinder)
(_
Connection
(_)
Back side of connection
weld.
nut to tank valve.
nut to brass
nipple.
(_)
Brass nipple connection
(_)
Regulator
hoses.
(_
Gas supply hose connection
burner valve assembly.
(_)
Side burner valve stem cap.
(_)
Side burner connection
(_)
Hose connection
(_)
The full length of gas supply hose.
(_
Tank valve to cylinder.
connections
into regulator.
to gas supply
to side
to hose.
to gas manifold.
8
6. Check each place listed (A-K)
for growing bubbles which indicates
a leak.
7. Turn off gas supply at cylinder valve.
8. Turn on control knobs to release gas pressure
in hose.
9. Turn control knobs to "OFF" position.
10. Tighten any leaking connections.
11. Repeat soapy water test until no leaks are detected.
12. Turn off gas supply at cylinder valve until you are ready to use your grill.
13. Wash off soapy residue with cold water and towel dry.
14. Wait 5 minutes to allow all gas to evacuate
,_
CAUTION!
the area before lighting grill.
DO NOT use the grill if leaks cannot be stopped.
Contact a qualified
gas appliance
repair service.
NOTE:
The leak test must be performed in an area that has adequate lighting in order to see if
bubbles are developing. DO NOT use a flashlight to check for bubbles.
PRE-START CHECK LIST:
Property damage, bodily harm, severe burns, and death could result from failure to follow these
safety steps.These
steps should be performed after the grill has been assembled and prior to each
use. DO NOT operate this grill until you have read and understand ALL of the warnings and
instructions in this manual.
PRE-START CHECK LIST:
•
Ensure that the grill is properly
assembled.
Inspect the gas supply hose for burns, chaffing, kinks, and proper routing before each use. If it is
evident there is excessive abrasion or wear, or the hose is cut, it must be replaced prior the grill being
used. Replace with hose and regulator, Model No. 155-2400-0, which can be obtained by contacting
customer service at 800-527-0717.
9
•
Leak check all gas connections
and hose. See section on "Leak Testing".
•
Ensure that all electrical supply cords are properly grounded. Keep any electrical supply cord and the
fuel supply hose away from any heated surfaces. Hose should be at least 3 inches from hot surfaces.
•
Position your grill on level ground in a well ventilated
materials, buildings and overhangs.
•
Properly place the empty grease tray under the grease drain hole in the bottom of the
grill to catch grease during use.
•
DO NOT obstruct the flow of combustion
location, a safe distance
and ventilation
air.
from combustible
Read, understand and follow all warnings and instructions contained in this manual. DO NOT skip
any of the warnings and instructions contained in the preceding sections of this manual.
LIGHTING INSTRUCTIONS:
Follow the instructions
exactly.
1.
OPEN THE GRILL LID before attempting to light a burner so that fumes
the grill. An explosion could occur if grill lid is down.
do not accumulate
2.
Check that all burner control knobs and the cylinder valve are turned to the "OFF"
3.
Turn on the fuel supply by rotating the cylinder valve knob counter-clockwise
4.
DO NOT stand with head, body, or arms over the grill when lighting.
inside
position.
to full open.
LIGHTING THE MAIN BURNERS:
@
1.
Open lid before lighting burner.
2.
Make sure all control knobs are in the "OFF" position.
NOTE: The CENTER
burners.
.
BURNER
must be lit first, then light the left and right
Push and turn the control knob for the CENTER BURNER to the "HIGH" position.
4.
Press the electronic
5.
If ignition does NOT occur in 5 seconds, turn control knob to "OFF", wait 5
igniter and hold for 3-5
minutes to allow gas to dissipate
seconds to light burner.
...........
'
....
I
and repeat lighting procedure.
6.
If the CENTER BURNER does not ignite using the push-button
Lighting the Main Burners" section.
igniter, wait 5 minutes, see "Match
7.
To light the left and right burners, push and turn control knobs to HIGH. Follow Step 5.
8.
To turn off, turn each control knob clockwise
the gas flow from the cylinder.
until it locks in the "OFF" position. This does not turn off
NOTE: If burner does not light or flame is too low, you may have spider or other insect blockage in burner,
or the flow limiting device has been activated. See "Burner Assembly/Maintenance"
under Proper
Care and Maintenance, or "Regulator Resetting Procedure" under Connecting LP Cylinder and
Hose/Regulator to Grill.
Lighting Hole
MATCH LIGHTING THE MAIN BURNERS:
1.
Open lid before lighting.
2.
Turn the burner control knobs to "OFF".
3.
Place a paper match in the end of the matchlighter. Strike the
match and place through lighting hole in the left hand side of the
grill to approximately
1/2" (1 to 2 cm) from the burner.
.
Turn on the FAR LEFT burner control knob to the "HIGH"
\
Matchlighter
position. The burner should light within 5 seconds.
.
.
.
If the burner does not light, turn the control knob to "OFF" and
wait 5 minutes for gas to dissipate and repeat lighting procedure.
Once lit, light adjacent burners
the "HIGH" position.
in sequence
by pressing in and rotating the control knob to
If the burner does not light within the first few attempts of match lighting, there is a problem with the
gas supply. Turn off the gas at the burner and cylinder. DO NOT attempt to operate the grill until the
problem is found and corrected. See "Trouble Shooting" section of this manual.
10
LIGHTING THE SIDE BURNER:
.
Open lid before lighting side burner.
2.
Make sure control knob is in the "OFF" position.
3.
Push and turn side burner control knob to the "HIGH" position.
4.
Press the electronic igniter on the main control
hold for 3-5 seconds to light burner.
5.
6.
panel and
siD_ BURNER
If ignition does NOT occur in 5 seconds, turn control knob to
"OFF", wait 5 minutes to allow gas to dissipate and repeat
lighting procedure.
To turn off, turn each control knob clockwise
"OFF" position.
_MJIDE
JZT_I_
until it locks in the
NOTE: If burner does not light or flame is too low, you may have spider or other insect blockage in burner,
or the flow limiting device has been activated. See "Burner Assembly/Maintenance"
under Proper
Care and Maintenance, or "Regulator Resetting Procedure" under Connecting LP Cylinder and
Hose/Regulator
to Grill.
MATCH LIGHTING THE SIDE BURNER:
1.
Open the lid to the side burner before lighting.
2.
Turn the burner control knob to "OFF".
3.
Strike and carefully
4.
Turn the side burner control knob to the "HIGH" position. The burner should light within 5 seconds.
5.
If the burner does not light, turn the control knob to "OFF" and wait 5 minutes for gas to dissipate
repeat lighting procedure.
6.
If the burner does not light within the first few attempts of match lighting, there is a problem with the
gas supply. Turn off the gas at the burner and cylinder. DO NOT attempt to operate the grill until the
problem is found and corrected. See "Trouble Shooting" section of this manual.
NOTE:
place a match approximately
1/2" (1 to 2 cm) from the burner.
Observe flame height when lit: Flame
should be a Blue/Yellow color between
1"-2"
when
burner is on "HIGH".
TURNING OFF THE GRILL:
1.
Turn off the cylinder valve.
2.
Turn all burner control knobs to the "OFF" position.
NOTE:
The cylinder valve should always be in the off,
or closed, position when the grill is not in use.
To turn off the cylinder valve,
turn knob clockwise until it stops.
11
1
m
2|
|W
|
0
||
Turn off LP cylinder first to prevent gas from being left in the system under pressure.
ACAUTION!
•
m
J
and
OPERATING THE GRILL:
Never use Charcoal or Lighter Fluid inside your Gas Grill. Read and follow
instructions contained in the preceding sections of this manual.
all warnings
and
BREAKING IN YOUR GRILL:
•
In manufacturing and preserving the components
burner and cooking surfaces of your grill.
of your grill, oil residue may be present on the
•
Before cooking on your grill for the first time you should preheat
off these residual oils.
it for 15 minutes on "HIGH" to burn
PREHEATING THE GRILL:
Prior to use, it is recommended that you preheat your grill. This ensures that the grilling surfaces are
at the desired temperatures to sear the food sugars when cooking. After lighting your grill, set the
main burner control knobs to the "HIGH" position for 10 to 15 minutes. Close the cover during the
preheat period.
CONTROLLING FLARE-UPS:
Flare-ups are a part of cooking meats on a gas grill. This adds to the unique flavor of cooking on a
gas grill. Excessive flare-ups can over-cook your food and cause a dangerous situation for you and
your grill. Excessive flare-ups result from the build-up of grease in the bottom of your grill. If this
should occur, DO NOT pour water onto the flames. This can cause the grease to splatter and could
result in serious burns or bodily harm. If grease fire occurs close the lid and turn off the main burners
until the grease burns out. Use caution when opening the lid as sudden flare-ups may occur.
•
DO NOT leave your grill unattended
while in use.
•
DO NOT move grill when in use. Lock wheels in place to stabilize
•
DO NOT use water to extinguish
•
Have fire extinguisher
grill.
flare-ups.
readily accessible
suitable for use with gas appliances.
TO MINIMIZE FLARE-UPS:
•
Trim excess fat from meats prior to cooking.
•
Cook meats with high fat contents
•
Ensure that your grill is on level ground and the grease is allowed to evacuate
drain hole in the bottom and into grease cup.
(chicken or pork) on Low settings
or indirectly.
the grill through the
INDIRECT COOKING:
•
Indirect cooking is the process of cooking your food without the heat source being directly under your
food. You can sear meats over a high flame on one side of the grill while slow cooking a roast on the
other (unlit) side of the grill.
t2
ROTISSERIE COOKING:
•
Your grill was pre-drilled from factory to include mounting holes for a rotisserie
not use a rotisserie not specifically manufactured for this grill.
•
Read and follow all instructions
•
Do not use the side burner when using a rotisserie.
provided
with the rotisserie.
Save instructions
(sold separately).
Do
for future reference.
When using an AC current rotisserie, it must be electrically grounded in accordance
codes, or in the absence of local codes:
•
In the US: The National Electrical Code - ANSI-NFPA No. 70 - Latest Edition
•
In Canada: the Canadian Electrical Code - CSA C22.1
with local
The Rotisserie is equipped with a three pronged plug for your protection against electrical
shock. This plug should be plugged directly into a properly grounded 3 prong receptacle. Never
cut or remove the grounding plug. Any extension cord must also have a 3 prong receptacle.
All electrical supply cords should be kept away from water and any hot surfaces of the grill.
USING
OTHER
FEATURES
OF THE GRILL:
THE SIDE BURNER:
•
The side burner can be used to prepare side dishes such as beans, potatoes, corn, or to warm
sauces.
•
The burner valve can be adjusted from high to low depending
Read instructions
upon your cooking demands.
on lighting your grill to light the side burner.
Never close the side burner cover when the burner is lit.
Use a 10" diameter pot or smaller that does NOT have an extended
side burner. Center pot over burner.
Never place more than 15 pounds on the side burner.The
weight exceeding 15 pounds.
handle when cooking on the
side burner is not constructed
to hold
Use caution to avoid bumping grill, side burner or pot to prevent pot from spilling contents
possibly leading to severe burns.
DO NOT use side burner to deep fry food in oil to avoid dangers associated
creating a very dangerous situation.
13
with oil igniting
GRILL
COOKING
TIPS
CLEANLINESS
•
Always wash hands thoroughly with soap and hot water prior to handling food and after handling raw
meat, uncooked poultry or seafood.
•
When using a platter to carry raw meat, uncooked poultry or seafood to the grill, make sure to wash the
platter thoroughly with soap and hot water before placing cooked foods back on the platter or use different
platters for raw and cooked foods.
•
Never use the same utensils when handling raw meat, uncooked poultry or seafood unless you wash the
utensils thoroughly with soap and hot water.
•
Never re-use marinade from raw meat or uncooked poultry on foods that have been cooked and are
ready to be served.
GRILLING TO PROPER TEMPERATURE
•
Use a meat thermometer to be sure food has reached a safe internal temperature. You may order a
Commercial-quality
thermometer from Brinkmann. For more information on this product and other
Brinkmann accessories, please refer to the accessory pages at the end of this manual.
•
The US Department of Agriculture recommends the minimum
following food items:
Chops
.....................
be reached for the
145 degrees F
Ground Meat ...............
160 degrees F
Pork .......................
160 degrees F
Poultry .....................
180 degrees F
Roasts .....................
145 degrees F
Seafood ....................
140 degrees F
Vegetables
145 degrees F
.................
temperature
HELPFUL HINTS
•
If you pre-cook meat or poultry, do so immediately before grilling.
•
Never defrost meat at room temperature
•
Refrigerate
•
For additional information, please phone the USDA's toll free Meat & Poultry Hotline at 800-535-4555.
or on a countertop.
leftovers within 2 hours of taking food off the grill.
PROPER
CARE
& MAINTENANCE
•
To protect your grill from excessive rust, the unit must be kept clean and covered at all times when not
in use. A grill cover may be ordered directly from Brinkmann by calling 800-468-5252 or 800-527-0717.
•
Wash cooking grills and heat distribution plates with hot, soapy water, rinse well and dry. Lightly coat
cooking grill with vegetable oil or vegetable oil spray.
•
Clean inside and outside of grill by wiping off with a damp cloth. Apply a light coat of vegetable
vegetable oil spray to the interior surface to prevent rusting.
•
The stainless steel exterior surface of your grill, can be cleaned with stainless steel cleaner.
•
Never apply paint to the interior surface. Rust spots on the interior surface can be buffed, cleaned, then
lightly coated with vegetable oil or vegetable oil spray to minimize rusting.
oil or
14
CLEANING AND MAINTENANCE:
•
Keep the appliance
and liquids.
•
Keep the ventilation
•
Visually check burner flames for proper operation (see pictorial in "Burner Assembly/Maintenance"
under Proper Care and Maintenance). Spiders or other insects can nest in the burner causing gas
blockage.
•
For safe grilling and peak performance
after extended periods of storage.
•
Be sure to tighten up all hardware
A'_ CAUTION!
•
free and clear of combustible
openings
materials,
of the cylinder enclosure
gasoline
and other flammable
vapors
free and clear of debris.
of your grill, perform these checks at least twice per year or
(nuts, bolts, screws, etc.) at least twice per year.
Some parts may contain sharp edges. Wear protective
gloves if necessary.
Remove the cooking grills, heat distribution plates, and burners from inside your grill. Use a brush with
hot water and detergent to remove excess residue. NEVER use a commercial oven cleaner. Rinse
completely with water. Towel dry and replace all components as described in the assembly instructions.
BURNER ASSEMBLY/MAINTENANCE
Although your burners are constructed of stainless steel, they may rust as a result of the extreme heat
and acids from cooking foods. Regularly inspect the burners for cracks, abnormal holes, and other
signs of corrosion damage. If found, replace the burner.
DO NOT obstruct the flow of combustion and ventilation air. Burner tubes can become blocked by
spiders and other insects building their nests. Blocked burner tubes can prevent gas flow to the burners
and could result in a burner tube fire or fire beneath the grill. To clean the Burner Assembly follow these
instructions
.
to clean and/or replace parts of burner assembly
Turn gas off at control knobs and LP cylinder tank valve.
2.
Remove cooking grills and heat distribution
3.
Remove screw from each burner "foot" using a screwdriver.
4.
Carefully lift each burner up and away from
valve openings.
.
or if you have trouble igniting the grill.
plates.
Use a narrow bottle brush or a stiff wire
bent into a small hook to run through each
burner tube and flame port several times.
NOTE: Wear eye protection
performing procedure 6.
.
Debris
when
Use compressed air to blow into burner tube and out the flame ports. Check each port to make sure air
comes out each hole.
7.
Wire brush entire outer surface of burner to remove food residue and dirt.
8.
Check burner for damage,
IMPORTANT:
9.
Carefully
if any large cracks or holes are found replace burner.
Burner opening
must slide over valve nozzle.
replace burners.
Valve Nozzle
10. Replace screw on each burner and follow the "Gas
Leak Testing" section of this manual. Relight
burners to verify proper operation.
1 1. Replace heat distribution
plates and cooking grills.
Burner Orifice
PROPER
t5
BURNER
OPERATION
COOKING GRILLS
•
Clean with mild soap detergent and water. A brass bristled brush or a nylon cleaning pad can be used
to remove residue from the stainless steel surfaces. Do not use steel wire bristles to clean the cooking
grills. Steel can cause the finish to chip or crack. DO NOT use a commercial oven cleaner.
HEAT DISTRIBUTION PLATES
Periodically, it may be necessary to inspect and clean the heat distribution plate to prevent excess
grease build-up. When the grill is cold, remove the cooking grill. Inspect the heat distribution plates
and replace if broken or damaged. Do not allow heat distribution plates to become damaged to the
extent that they may fall through onto the burners. Replace the heat distribution plates and cooking
grills and light the burners. Operate the grill on "HIGH" for 10 minutes to remove the excess grease.
TRANSPORTING AND STORAGE:
•
Never move a grill when it is hot or when objects are on the cooking
•
Make sure that cylinder valve is shut off. After moving the grill check that all gas connections
are free of leaks. Refer to instructions for Leak Testing.
•
DO NOT store a spare LP gas cylinder (filled or empty) under or near the grill.
•
Never store flammable
•
DO NOT extinguish
•
If the outdoor
cylinder.
•
Storage of an outdoor cooking gas appliance indoors is permissible only if the cylinder is
disconnected and removed from the outdoor cooking gas appliance.
•
Cylinders must be stored outdoors out of reach of children and must not be stored in a
building, garage or any other enclosed area.
•
When removing the grill from storage, spider webs or other debris may be blocking the burner.
See "Burner Assembly/Maintenance"
under Proper Care and Maintenance.
liquids or spray canisters
surfaces.
under or near the grill.
grease fires using water.
cooking gas appliance
is not in use, the gas must be turned off at the supply
BEFORE STORING YOUR GRILL:
•
Ensure that the cylinder valve is fully closed.
•
Clean all surfaces.
•
Lightly coat the burners with cooking oil to prevent excess rusting.
•
If storing the grill indoors, disconnect
•
Place a protective
of direct sunlight.
•
Clean burner prior to use after storing, at the beginning of grilling season or after a period of one
month not being used. Spiders and insects like to build nests in burner tubes (especially during colder
months). These nests can cause fires in burner tubes or under grill.
•
If storing the grill outdoors, cover the grill with a grill cover for protection from the weather. A grill cover
may be ordered directly from Brinkmann by calling 800-468-5252 or 800-527-0717.
the LP tank and leave the LP tank OUTDOORS.
cap cover on the LP tank and store the tank outdoors
in a well ventilated
area out
t6
TROUBLE SHOOTING
Problem:
Possible Causes:
1.
2.
Burner will not light
3.
4.
5.
6.
Fire at control
knob
1.
Burner holes may be obstructed.
"Burner Assembly/Maintenance"
and Maintenance.
2.
3.
Burner is improperly seated on control valve.
Gas connections may be loose.
Leak Check and tighten all connections.
1.
Burner is obstructed.
Yellow Flames at burner
Flame
Burner
See section on
under Proper Care
1.
Burner holes may be obstructed.
"Burner Assembly/Maintenance"
and Maintenance.
See section on
under Proper Care
2.
3.
Grill is not sufficiently preheated.
Burner is improperly seated on control valve.
1.
Flow control device has been activated in regulator.
See Regulator Resetting Procedure under
Connecting LP Cylinder and Hose/Regulator
to Grill.
1.
2.
Excess grease build-up causing grease fires.
Damaged or faulty regulator.
Replace with factory authorized parts.
Cook on a lower temperature setting.
does not get hot enough
3.
t7
See section on
under Proper Care
"Burner Assembly/Maintenance"
and Maintenance.
blows out on "LOW"
Grill is Too Hot
Check LP cylinder fuel level.
Bad electrode spark.
Check to see if the grill will match light.
Electrode or collector may need adjustment.
Burner may not be properly seated.
Burner may be obstructed.
The cylinder valve may be closed.
Regulator is not properly seated on cylinder valve.
FREQUENTLY
ASKED
QUESTIONS
Your grill's serial number and model number, and the contact information for Brinkmann Customer
listed on a silver label found on the back of the grill or on the grill body side, under the side shelf.
These questions
and answers are for your general knowledge,
and may not be applicable
Service, are
to your model grill.
Question: Why does my grill not light properly?
Answer: Always follow lighting instructions
causes:
as listed on the control panel or in this manual. Also check these
•
Check LP gas supply.
•
Check to ensure all gas connections
•
The igniter AA battery may need replacing.
•
Ignition wires may be loose. Remove the battery, inspect the igniter junction box found behind the control
panel and connect any loose wires.
•
Spark electrode tips may need repositioning. With the gas supply closed and control knob set to the "OFF"
position, press the igniter button and have another person watch for the presence of a spark at the
electrode tips. The gap between the spark electrode tip and spark receiver should be about 3/16". If the
electrode tip needs to be adjusted, bend it to the appropriate gap distance.
•
Check that the end of each burner venturi tube is properly
•
There may be an obstruction in the gas line. To correct this, remove LP gas hose / regulator or natural gas
fuel line from your grill. Open gas supply for one second to test for obstruction. If no obstruction is present,
reconnect fuel line. If the fuel line is blocked, replace with a new hose / regulator assembly.
•
If an obstruction is suspected in the hose / regulator
Customer Service at 800-527-0717.
are secure.
located over its gas valve orifice fitting.
assembly, orifice or gas valves call Brinkmann
Question: Why does my LP gas grill have a low flame or a flame with orange / yellow color?
Answer: You need to purge air from the gas line or reset the regulator's flow limiting device. Opening the
cylinder valve all the way or too quickly triggers the regulator's flow limiting device to shut down the gas flow,
which prevents excessive gas flow to your grill. NOTE: This procedure should be done every time a new LP gas
tank is connected to your grill:
RESETTING
THE REGULATOR
FLOW LIMITING
DEVICE
•
Turn control knob to the "OFF" position.
•
Turn off the LP gas tank at the cylinder valve.
•
Disconnect
•
Let tank stand for two minutes.
•
Reconnect
•
Open grill lid or side burner lid. Turn the cylinder valve on slowly until 1/4 or 1/2 open.
•
Light the grill by following the instructions
Question:
regulator from LP gas tank.
regulator to the LP gas tank.
How and when do I clean the interior
on your control panel or in this owner's manual.
cooking
components
of my grill?
Answer: Use a fiber or brass cleaning brush to clean the interior or the grill, cooking grills, heat distribution
plates and grease containers. Never use a wire brush or metal scraper on porcelain-finished
parts, as they can
scratch or chip the porcelain finish and promote rusting.
18
FREQUENTLY
ASKED
QUESTIONS
Cleaning Stainless Steel Cooking Grills: Wash grills with a mild detergent and rinse with hot water before
initial use and as needed. DO NOT use a commercial oven cleaner. For stubborn food residue, use a
degreaser and fiber or brass cleaning brush.
Cleaning Porcelain-Finished
Cast-Iron Cooking Grills: Wash grills with a mild detergent and rinse with hot
water before initial use and as needed. For stubborn food residue, use a degreaser and fiber or brass cleaning
brush. Dry immediately using a soft cloth or paper towels.
Cleaning Heat Distribution Plate: Heat distribution plates should be cleaned whenever food or grease
drippings accumulate to reduce the chance of flare-ups. Wash heat distribution plates with a mild detergent and
rinse with hot water. Use a degreaser and fiber or brass cleaning brush to remove stubborn food residue. Do
not use a wire brush or metal scraper on porcelain-finished
heat distribution plates, as they can scratch or chip
the porcelain finish and promote rusting.
Cleaning the Grease Tray and/or Grease Cup: The grease tray and/or grease cup (some models) should be
inspected before each grill use to reduce the chance of fire. Remove grease (a plastic spatula works well) and
wash all parts with a mild soap or degreaser and warm water solution.
Question: What causes grill parts to rust and what affect does it have on the grill materials?
Answer: Rusting is a natural oxidation process and may appear on cast-iron and steel parts. Rust will not
affect the short-term performance of your grill. Stainless steel grill parts will not rust. However, weathering and
extreme heat can cause a stainless steel lid to turn a bronze color. This is discoloration, not rust, and is not
considered a manufacturing defect.
Question: What causes my stainless
steel grill lid to discolor and how do I clean my grill lid?
Answer: Smoke, weathering and high heat can cause a stainless steel grill lid to turn bronze in
not to be confused with rust and is not a product defect. Machine oils used in the manufacturing
stainless steel as well as cooking oils and a dirty grill lid can also encourage discoloration if the
cleaned prior to grill use. After your grill is assembled, remove the protective PVC film from your
use a stainless steel cleaner and soft cloth to remove residual adhesive and oils from the inside
color. This is
process of
lid is not
grill lid and
and outside of
your grill lid. Never use abrasive cleaners or scrubbers. In addition to the initial cleaning, routine cleaning to
remove dirt, grease and oils will help discourage lid discoloration.
Question:
Can I convert my grill from
propane gas to natural gas?
Answer: Most gas grills are manufactured to exact specifications and are certified for either propane gas or
natural gas use only. However, some models can be converted safely with conversion kits available for specific
models. Contact Brinkmann Customer Service at 800-527-0717 to see if your grill can be converted.
Question: Why does the hose / regulator assembly
used for years?
supplied
with my grill not fit the older LP gas tank rye
Answer: U.S. Government regulates gas appliances and LP gas tanks. When regulations were changed, the
LP gas tank fittings were updated to ensure compliance. If your LP gas tank does not fit the hose / regulator
supplied with your new grill, the tank is outdated and must be replaced. NOTE: Effective April 1, 2002, all LP
gas tanks sold must include an "OPD" overflow protection device. This internal device prevents the LP gas tank
from being overfilled. Tanks without an OPD valve cannot be refilled.
Question:
Sometimes
I hear a humming
sound coming from my gas regulator. Should I be concerned?
Answer: The humming sound is gas flowing through the regulator. A low volume of noise is normal and will not
interfere with the operation of your grill. If the humming noise is loud and excessive, you need to purge air from
the gas line or reset the regulator flow limiting device following the Regulator Resetting Procedure under
Connecting LP Cylinder and Hose/Regulator to Grill. This procedure should be done every time a new LP gas
tank is connected to your grill. For help, refer to your owner's manual or call Brinkmann Customer Service at
800-527-0717.
t9
PARTS
BAG
CONTENTS
Make sure you have all items listed under PARTS LIST and PARTS CARD CONTENTS
you begin the installation process.
before
PARTS CARD CONTAINS:
Qty.
1 Hex nut wrench
1
1
26
AA/I.5V
Alkaline
Screwdriver
M6 X 12mm
Qty.
4
M5 X 10mm bolts
battery
14
2
bolts
2
3
Star washers
Wheel axle bolts
Wheel washers
#8 self tapping screws
Screwdriver
M6 X 12mm bolts
#8 self-tapping
Wheel
Wheel
axle bolts
screws
AA/1.5V
Alkaline
battery
washers
M5 X 10mm bolts
Star washers
20
ASSEMBLY
INSTRUCTIONS
READ ALL SAFETY WARNINGS
BEFORE ASSEMBLING
WE RECOMMEND
TWO PEOPLE
& ASSEMBLY INSTRUCTIONS
CAREFULLY
OR OPERATING YOUR GRILL.
WORK TOGETHER
WHEN ASSEMBLING
THIS UNIT.
The estimated time of assembly for this grill is approximately
45 minutes.
The following provided tools are required to assemble this Brinkmann Grand Gourmet
Grill:
•
•
Flathead Screwdriver
Hex Nut Wrench
PARTS LIST:
21
(_)
1
Hood
(_)
1
Side Burner Base
(_
1
Hood Handle
@
1
Side Burner Base Front Panel
1
Grill Body Assembly
(_)
1
Grease Cup
(_)
3
Stainless Steel Tube Burners
(_)
1
Left Cart Assembly
(_)
1
Warming
1
Right Cart Assembly
(_
3
Control Knobs
@
1
Side Burner Knob
Q
2
Cooking Grills
@
1
Side Burner Bezel
(_)
1
Tank Heat Shield
1
Heat Shield Plate
Rack
(_)
1
Grease Tray
(_
3
Heat Distribution Plates
(_)
1
Electronic Igniter Button
(_)
1
Loop Strap Bracket
@
1
Electronic Igniter Spring
(_)
1
Cart Base
@
1
Left Side Table
(_)
2
Locking Casters
(_)
1
Left Side Table Front Panel
1
Hose Heat Shield
(_
2
Hubcaps
2
Wheels
(_)
1
Cart Front Panel
(_)
1
Side Burner Grate
6345
\
t
FOR MISSING
PARTS, PLEASE
Inspect contents
CALL CUSTOMER
SERVICE
AT 800-527-0717.
(Proof of purchase will be required.)
of the box to ensure all parts are included and undamaged.
22
Choose a good, cleared assembly
area and get a friend to help you put
"t
your grill together. Lay cardboard
down to protect grill finish and
assembly area.
A'k CAUTION!
Some parts may
contain sharp edges.
Wear protective gloves
if necessary.
Step
1
Assemble bottom cart (Item #26)
shelf and right side cart
(Item #20) panel by using two
M6 X 12mm bolts and star
o
t_
(m=c_-- -"
washers (hand tighten only at
this point).
2
/
Step
2
Assemble
bottom cart shelf and left
side (Item #19) cart panel by using
two M6 X 12mm bolts and star
washers. Tighten all four M6 X 12mm
bolts at this time.
+
,
'---@_@
"-- -_)_4)
Step
3
Attach loop strap bracket (Item #25)
onto bottom cart shelf by using two
M6 X 12mm bolts.
I
I
23
I
o
/
,/
Step 4
With the help of a friend, turn the
assembled cart over. Try to minimize
the stress to the bottom plate.
Locking Caster
Hex Nut Wrench
Step 5
Attach locking casters (Item #27) to
the bottom of the left side cart
panel. Tighten caster bolts securely
using hex nut wrench provided in
parts card.
Wheel
Leg
Hubcap
bolt
Step 6
Install the wheels (Item #30) as
Wheel axle
illustrated, by inserting the wheel
axle bolts through the wheels
(Item #30), washers and right side
panel axle holes. Tighten axle bolts
securely using hex nut wrench
provided in parts card.
24
Step 7
Snap wheel hub caps (Item #29)
onto the outside of wheels as
illustrated.
Hubcap
'I
Step
8
With the help of a friend, turn the
cart to its upright position.
%
Heat Shield
Plate
Step 9
Attach tank heat shield
Tank
Heat Shield
(Item #23)
to heat shield plate (Item #24)
using one #8 self-tapping screw.
/-
..........
\
Step 10
Attach front panel (Item #14) to
lower left and right leg of cart
assembly using two M6 X 12mm
bolts and star washers.
d
::::::::::::::::::::::
C2............................
_
____
25
_
Step
11
Attach heat shield plate (Item #24)
and front panel to the front of the
Heat Shield Plate
cart frame assembly using two
M6 X 12mm bolts with star washers.
/
_
c
_ _-
_j
c
C_CCCCCCZb
¢
Step 12
Attach heat shield plate (Item #24)
to the back of the cart frame
assembly using two M6 X 12mm
bolts with star washers.
¢
i
C
C
C
C
Grease Cup
Heat
Plate
_
Siield
I
I
I
Step
13
Place grease cup (Item #18) in
middle of hole in heat shield plate.
26
Note: When performing Step 14,
Lift grill body from front and
rear panels to avoid injury to
/
........-- Grill Body
Assembly
hands and fingers. Be sure
to pass hose/regulator
assembly above cart frame
crossbar.
Step 14
With the help of a friend, place grill
body assembly on assembled cart
frame. Grill body will rest on angled
top of vertical supports. Align bolt
holes located on the outside of the
/
!'
grill body assembly. Secure using
four M6 X12mm bolts with star
washers.
[
o
27
_
C;Z:22222;2_
•
C2:2:2::;;_2;_
Side Table
Front Panel
Step 15
Side Table
Attach the side table front panel
(Item #13) to side table (Item #12)
with two M5 x 10mm.
/
Step
16
Attach the side burner front panel
Side Burner
•
i_--
Side Burner
Front Panel
(Item #17) to side burner base
(Item #16) with two M5 x 10mm.
Step
17
Attach the side table assembly to
the left cart frame (Item #19). Insert
two M6 x 12mm bolts into both left
legs halfway. Place table over bolts
and slide toward front of grill, then
tighten securely. Fasten side table
front panel to grill body with one
M6 X 12MM bolt.
\\
®
/
®
28
Step
18
Attach the side burner assembly to
the right side of the grill body. Insert
two M6 x 12mm bolts into both right
legs halfway. Place side burner
assembly over bolts and slide toward
front of grill, then tighten securely.
Fasten side burner front panel to grill
body with one M6 X 12mm bolt.
®
/
®
Step
19
Attach the hose heat shield
Hose
Heat Shield
(Item #28) to the right cart frame
(Item #20) using two #8 self-tapping
screws.
f
Step 20
Remove two screws and washers
from the side burner valve. Insert the
side burner valve assembly through
the hole in the side burner front
Burner Venturi
panel (Item #16), then firmly seat
the valve nozzle into the burner
venturi. Hold in place while you
perform Step 23.
Warning:
Never use your grill
without leak testing all
gas connections and
hoses. See the section on
"Leak Testing" in this
manual for proper
procedures.
29
(See Page 8)
Side
Burner
Valve
Valve
Nozzl_
Burner
Side
Control
Knob
,
Step
I
I
21
Place the bezel (Item #22) over the
control knob (Item #21) mounting
stem and position over holes in
side burner base and side burner
...................................................
Be_
valve assembly. Attach with two M4
bolts with lock washers which come
with valve. Then install the side
burner control knob (Item #21)
onto valve stem.
Step 22
Attach side burner igniter lead wire
to the electrode as illustrated.
Step 23
Electrode
Insert grease tray (Item #8) into
opening on backside of grill. Make
sure to slide tray onto tracks as
illustrated.
®
Grease Tray
3O
Step 24
Place the heat distribution plates
(Item #9) on lower level of grill
body assembly directly above
burners.
/Z_
jWarming
ii
__
l__,_--Cooking
Rack
Grills
_Heat
Step
25
__
Place cooking grills (Item #7) on
/_
,I _'_
Distribution
Plates
support ribs directly above heat
distribution plates (Item #9).
Step 26
Place warming rack (Item #5) in
grooves so that it sits above the
cooking grills.
_,_,_:,,_:_,_s;:_
............
..... ....:@_ii
_ ÷_
....@'=i::i
...........
,_
...........
_Lt8_z7_717
Step 27
Remove electronic igniter button
(Item #10) and insert battery with
positive end of battery toward
Electronic
Igniter Button
igniter cap. Replace electronic
igniter button (Item #10) and make
sure the igniter is working properly.
HIGH
Battery
31
ProSeries
6345 (Assembled)
_
)
(c-------_)
£c_
))
(czzzZZ_)
32
ACCESSORIES
RIB RACK
PROFESSIONAL
SHISH-KABOB
SKEWERS
Chrome-plated rack can greatly increase the cooking
capacity of your grill. Holds ribs, chicken halves, potatoes
and corn vertically to triple cooking capacity. Allows
smoke, steam and heat to penetrate food evenly.
These heaw-duty, 18" shish-kabob skewers are extra-long for fabulous
restaurant style kabobs. Made of rust resistant stainless
steel to last for years.
SET OF 12
812-2904-0
812-3310-0
MEATLOAF
BASKET
SMOKER
The unique basket weave prevents meatloaf from falling
through the grill while allowing smoke, steam and heat to
flow into the food. Also, provides a convenient method for
lifting your meatloaf in and out of the smoker.
BASKET
The unique basket weave prevents food from falling through the grill while
allowing smoke, steam and heat to flow into the food. Great for fish, shrimp,
vegetables and hors d'oeuvres.
812-3333-0
812-0073-0
CHICKEN
AND TURKEY
RACKS
These chromed steel racks hold chicken, cornish hen, duck or
turkey upright and are ideal for smoking, grilling or oven roasting
poultry.The rack allows the meat to cook from the inside as well
as from the outside. This speeds up cooking time, seals in flavorful juices and promotes even browning of skin. It's a low fat way to
cook poultry because excess fat drips off the meat. When oven
roasting, place poultry on rack in a shallow pan of water to steam
baste to tender perfection. When grilling or smoking, simply place
poultry on rack atop the grill. Makes carving easier, too.
COMMERCIAL-QUALITY
An essential tool when cooking all types of meat. Get perfectly smoked
roasts, briskets and turkeys without cutting into the meat. Commercialquality thermostat features an easy-to-read 2 3/4"
CHICKEN RACKS (SET OF TWO)
885-9015-0
TURKEY RACK
885-9025-0
MEAT THERMOMETER
¥
and Centigrade readings and
National Livestock and Meat
Board recommended
wide
temperatures.
dial with a 5 Also
1/4" stem.
features
Features
the newly
Fahrenheit
recommended 170°F internal temperature for fresh
pork. Stainless steel construction and dishwasher
safe.
812-4100-0
33
ACCESSORIES
2-GALLON
PAN & BASKET
SET
Restaurant-style aluminum fry pan with nickel plated
wire straining basket is an essential tool for frying fish,
chicken, french fries, onion rings and more. Strainer
basket holder helps drain excess oil. Use outdoors with
the Brinkmann Backyard Kitchen and avoid the mess
and odor of frying indoors.
MULTI-PURPOSE
SPATULA
815-3610-0
If you could have only one BBQ
tool, this multi-purpose spatula is it!
Aside from being a great spatula, it
features a serrated edge for cutting, a
bottle opener, and special grooved edges for
cleaning grills. Made of heaw-gauge stainless
steel to last for years. Beautiful rosewood
handles are slotted and riveted for maximum
strength and durability. Includes leather hanging
straps for convenient storage.
812-5047-0
STAINLESS
STEEL
WOOD CHIP SMOKING
BOX
Rugged stainless steel smoking box allows wood chips to
burn longer for richer smoke flavor and provides easy
cleanup of ashes. Ideal
for charcoal, electric, gas
smokers and grills.
812-3311-0
SMOKE'N
v
SPICE
SEASONING
These custom blended spices are a delicious
marinade seasoning for smoke cooking and
grilling. Contains no MSG. Available in red and
white meat varieties in a money-saving 2-pack.
812-3322-0
MARINADE
INJECTOR
This quick and easy marinade injector marinates meat fi'
in 5 minutes, not hours.1 Mix your favorite marinade
....ji /
and spices into a liquid and inject into turkey, roast,
chicken or steak for a naturally tenderized and
flavorful delight. The reusable Marinade Injector
includes a heaw-duty stainless steel needle and
heaw-gauge plastic syringe to last for years.
812-5059-0
LOOK FOR THESE AND OTHER BRINKMANN
ACCESSORIES
ATYOUR LOCAL
WHERE SMOKERS ARE SOLD, OR ORDER DIRECT BY CALLING
800-468-5252.
RETAILER
34
@2005 The Brinkmann Corporation
Dallas, Texas 75244 U.S.A
www.brinkmann.net
The Brinkmann Corporation warrants to the original purchaser that the Brinkmann Grand Gourmet 6345 is free from
defects due to workmanship or materials for:
Stainless Steel & Die cast parts - Lifetime
Electronic ignition and burners - 1 Year
Remaining parts - 1 Year
The Brinkmann Corporation's obligations under this warranty are limited to the following guidelines:
• This warranty does not cover grills that have been altered or damaged due to: normal wear, rust, abuse, improper
maintenance, improper use, disassembly of parts and/or attempted repair by anyone other than an authorized
employee of The Brinkmann Corporation.
• This warranty does not cover surface scratches, rust or heat damage to the finish, which is considered normal
wear.
• The Brinkmann Corporation may elect to repair or replace damaged units covered by the terms of this warranty.
• This warranty extends to the original purchaser only and is not transferable or assignable to subsequent
purchasers.
The Brinkmann Corporation requires reasonable proof of purchase. Therefore, we strongly recommend that you retain
your sales receipt or invoice. To obtain replacement parts for your Brinkmann Grand Gourmet 6345 under the terms of
this warranty, please call Customer Service Department at 800-527-0717. A receipt will be required. The Brinkmann
Corporation will not be responsible for any grills forwarded to us without prior authorization.
EXCEPT AS ABOVE STATED, THE BRINKMANN CORPORATION MAKES NO OTHER EXPRESS WARRANTY.
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
LIMITED IN DURATION TO THOSE LISTED ABOVE FROM THE DATE OF PURCHASE. SOME STATES DO NOT
ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT
APPLY TO YOU.
ANY LIABILITY FOR INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM THE FAILURE OF
THE BRINKMANN GRAND GOURMET 6345 TO COMPLY WITH THIS WARRANTY OR ANY IMPLIED WARRANTY IS
EXCLUDED. CUSTOMER ACKNOWLEDGES THAT THE PURCHASE PRICE CHARGED IS BASED UPON THE
LIMITATIONS CONTAINED IN THE WARRANTY SET OUT ABOVE. SOME STATES DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR
EXCLUSION MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY
ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
140-6345-0
10/05
Owner's
Manual for Model
810-6345-0