Owner`s manual | Broilmaster SS26P-1 Gas Grill User Manual

Installation Instructions
MODELS
MODELS
PCB1-2
DCB1-2
BL26P-1
SS26P-1
MODELS
BL48G-1
SS48G-1
B101652
Verify that all parts listed on the exploded view of this manual have been included in
this Carton before beginning installation.
Caution: Use caution when handling parts, as they may contain sharp edges.
Work gloves are recommended to prevent injury.
Keep This Owner’s Manual For Future Reference.
Empire Comfort Systems, Inc • 918 Freeburg Ave. • Belleville, IL 62220
B101586-4-0112
Page 1
Table of Contents
Congratulations!
You have chosen the finest grill for your outdoor cooking pleasure. Please take time to read this entire manual before assembling your Broilmaster® Grill accessory.
Important Information ...........................................................................................................4
PCB1-2, DCB1-2 Installation Instructions .......................................................................5-10
Cart Exploded View & Parts List ........................................................................................6
Cart Hardware Package.....................................................................................................7
Cart Assembly ..............................................................................................................8-10
BL26P-1, SS26P-1 Patio Base Installation Instructions ................................................11-16
Patio Base Exploded View & Parts List ...........................................................................12
Patio Base Hardware Package........................................................................................13
Patio Base Installation ................................................................................................14-16
BL48G-1, SS48G-1 In-Ground Post Installation Instructions ........................................14-22
In-Ground Post Exploded View & Parts List ....................................................................18
In-Ground Post Hardware Package.................................................................................19
In-Ground Post Assembly ...........................................................................................20-22
Template for Mounting Holes ..............................................................................................23
Page 2
B101586-4-0112
This Gas Accessory Is Designed For Outdoor Use Only
IMPORTANT:
This manual should be read thoroughly by the person installing the grill mounting and all persons who will
use and maintain the grill mounting. The installer should be sure the manual is left in the possession of the
user. The user should retain this manual for future reference when using or cleaning the grill mounting and to
properly identify any repair parts that may be required.
WARNING:
Reference this manual for proper installation and maintenance instructions. Improper installation, adjustment,
alteration, service or maintenance can cause personal injury or property damage. For assistance or additional
information consult a qualified installer, service agency or the gas supplier.
CAUTION:
The grill and its individual shutoff valve must be disconnected from the gas supply piping system during any pressure
testing of that system at test pressures in excess of 1/2 PSIG.
CAUTION:
The grill must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any
pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 PSIG.
CAUTION:
Parts may have sharp edges. Wear leather work gloves and handle parts carefully during the unpacking,
assembly and the installation.
WARNING:
Do not supply LP gas to a grill designed for natural gas nor natural gas to a grill designed for LP gas.
NOTICE:
Assemble grill mount before assembling grill.
B101586-4-0112
Page 3
Important information
Grill Location
Broilmaster® Gas Grills are designed for outdoor use
ONLY.
These mounting accessories are designed for use with
Broilmaster® gas grills and must not be used with any
other grill or for any other purpose.
Gas Types
Never use liquid propane gas with a grill designed for
natural gas, or natural gas with a grill designed for liquid
propane gas. The type of gas required for your grill is
defined on its product identification label. Questions
regarding different types of gases should be directed
to your gas supplier.
Never install or operate your grill in any building, garage, or other enclosed area. To do so may result in the
possibility of fire, property damage, or personal injury.
Cleaning
For your safety, the grill should not be installed or
operated under any combustible materials, such as
carports, covered porches, awnings, or overhangs. To
do so may result in the possibility of fire, property damage, or personal injury.
Touch-up paint is available through your Broilmaster®
dealer.
Never install or use your grill in or on any recreational
vehicle or boat. To do so may result in the possibility of
fire, property damage, or personal injury.
CAUTION: The
installation and operation of this
grill at clearances less than specified below may lead
to the possibility of fire, property damage, or personal
injury.
A minimum clearance of eighteen (18”) inches is required from the back of the grill to any combustible
material.
Examples of combustible materials are patio furniture,
fences, or the wall of your home.
The area surrounding the grill should be clear to ensure
proper ventilation. Do not obstruct the flow of combustion and ventilation air in any way. The ventilation
openings on the propane cylinder enclosure must also
remain free and clear of debris.
WARNING: Do
The exterior of your cart or post may be cleaned with
hot water and mild detergent as needed.
Stainless steel surfaces may be cleaned with a sprayon stainless steel cleaner available at most hardware
stores.
Important: Do not use harsh or abrasive cleaners! Your
cart or post has a highly polished surface and may be
easily scratched.
Periodic Inspection and
Maintenance
Periodic inspections and maintenance are essential. All
Broilmaster® Gas Grill products or mechanical devices
eventually begin to wear due to environment, contaminants, corrosion or aging. Inspect all components at
least twice per year and replace any that show wear.
If any parts are damaged or missing, you may order parts
from your local Broilmaster® dealer. Please refer to the
Parts Diagram and Parts List section of this manual for
more detailed information.
not install or operate a gas grill
where gasoline or other flammable materials are used
or stored.
Failure
to comply with this warning could
result in explosion or fire causing property damage or
personal injury.
Page 4
B101586-4-0112
PCB1-2, DCB1-2
Installation Instructions
Verify that all parts listed on the exploded view of this manual have been included in
this Carton before beginning installation.
Caution: Use caution when handling parts, as they may contain sharp edges. Work
gloves are recommended to prevent injury.
Remove protective coating and verify that all parts listed on the exploded view of this manual have
been included before beginning assembly.
Tools Required: Phillips Screw Driver (An electric screw driver or drill is
recommended to ease installation.)
B101586-4-0112
Page 5
Cart Exploded View & Parts List
4
11
6
10
12
13
3
5
2
1
7
9
8
Remove protective coating from stainless steel parts starting at pop rivets and verify that all parts listed in the
exploded view on this page have been included before beginning this
installation.
Caution: Use caution when handling parts, as they may contain sharp edges.
Work gloves are recommended to prevent injury.
PART NO.
INDEX
NO.
PCB1
DCB1
H3PK1
1
B101585
B101584
B101584
Front Panel
2
B101651
B101642
B101642
Right Side Panel Assembly
3
B101650
B101641
B101641
Left Side Panel Assembly
4
B101583
B101582
B101582
Rear Brace
5
B101633
B101633
B101633
Cart shield stainless steel
6
B101473
B101473
B101473
Grease Cup
7
B101414
B101414
B101415
Plastic Base
8
B101416
B101416
B101416
Caster with Brake
9
B101417
B101417
B101417
Caster without Brake
10
B064791
B064791
B064791
Cylinder Retainer
DESCRIPTION
11
B101565
B101565
B101565
Base Support Bracket - Right
12
B101495
B101495
B101495
Base Support Bracket - Left
13
B101635
B101635
B101635
Channel, Edge Protector
All repair part orders should be placed through your local Broilmaster dealer. To locate a dealer in your area, visit
www.broilmaster.com and click on the dealer locator. To ensure prompt and accurate service, please provide the following
information when placing a repair part order: Model Number, Part Name, Part Number, and Quantity of parts needed.
Page 6
B101586-4-0112
Cart Hardware Package
10-24 KEPS NUT
PHILLIPS TRUSS HEAD SCREW 1/4-20 X 3/4
1/4-20 WING NUT
HEX HEAD BOLT 1/4-20 X 3/4
½ SNAP BUSHING
1/4-20 HEX NUT
1/4 ID X 1/2 OD LOCK WASHER
PHILLIPS TRUSS HEAD SCREW 1/4-20 X 1 1/4
PHILLIPS SCREW 10-24 X 1/2
1/4 ID X 5/8 OD FLAT WASHER
Note: Hardware shown at actual size where possible.
Description
Qty
Supplied
Description
Qty
Supplied
PHILLIPS TRUSS HEAD SCREW 1/4-20 X 3/4
8
10-24 KEPS NUT
6
HEX HEAD BOLT 1/4-20 X 3/4
4
1/4-20 WING NUT
1
1/4-20 HEX NUT
4
1/2 SNAP BUSHING
1
1/4 ID X 1/2 OD LOCK WASHER
1
PHILLIPS TRUSS HEAD SCREW 1/4-20 X 1 1/4
1
PHILLIPS SCREW 10-24 X 1/2
6
1/4 ID X 5/8 OD FLAT WASHER
4
B101586-4-0112
Page 7
Cart Assembly
Caution: Be careful when handling parts, as they may
contain sharp edges. Work gloves are recommended to prevent
injury. Remove protective plastic covering.
1. For Stationary Cart Assembly: Use the template on page
23 to locate and pre-drill the three screw holes into wood or
concrete for the cart base. If applicable, drill the 1 1/2” gas line
access hole. DO NOT secure base with the screws at this time.
For Mobile Cart Assembly: Flip plastic base and insert casters
by inserting the pin provided with the casters in the proper hole.
It is recommended that the two casters with brakes should be
in the front of the base. See Figure 1.
3. Align the holes on the front and side panel assemblies and
secure with six #10-24 x 1/2” Phillips screws and 10-24 Keps
Nuts provided (3 on each side). Do not tighten these screws
until all are installed. Use black screws for black carts and
stainless steel screws for stainless steel carts. See Figures 2
and 3.
Figure 1
2. Place the base support brackets on the side panels. Slide the
short flanges on the brackets between the top and side flanges
of the side panels. See Figure 2.
Figure 3
4. Secure the completed assembly to the base with four
1/4-20 x 3/4” Phillips Truss screws. See Figure 4. Note: Plastic
base comes with factory installed threaded inserts. Install all
four screws before tightening.
Figure 2
Page 8
Figure 4
B101586-4-0112
Cart Assembly
5. Attach Rear Brace to the Left and Right Side Assemblies with
two 1/4-20 x 3/4” Phillips Truss Head screws and 1/4-20 Hex
nuts. See Figure 5. Important: Make sure the brace goes in
the cutout of the support bracket.
Figure 5
6. Insert bushing in the front panel on the right for P and H series
and on the left for R and T series grills. Install rubber guard
over cart cut out. See Figure 6.
Figure 7
8. Attach the Heat Shield to the Left and Right side assemblies
with two 1/4-20 x 3/4 Phillips Truss Head screws and 1/4-20
Hex nuts. Make sure shield is resting on the cutout provided
in the side panels before tightening the screws and nuts. See
Figures 8 and 9. Note: Grill head removed for clarity.
Figure 6
Note: Bushing is used to protect the ignitor wires from
rubbing on the front panel when they are in place.
Note: Ignitor wires must go through the bushing before grill
head is fully installed.
7. Secure the grill head to the cart using four 1/4-20 x 3/4” Hex
Head Bolts and 1/4 x 5/8 Flat Washers. See Figure 7. Note:
To ease assembly, you may wish to install the ignitor as
shown in your Broilmaster® grill manual before attaching
the grill to the cart.
B101586-4-0112
Figure 8
Figure 9
Page 9
Cart Assembly
9. For Grill Heads other than R3 Series, continue on to Step 10.
For R3 Series Grill Heads: Press in the two sides of the
Control Housing (provided with Grill Head) and fit it into the
opening under the grill head as shown in Figure 10. Grill
Assembly will look like Figure 11. Note: It may be easier to insert one side of the control housing
first, and then press in the other side using the cart as a brace
for the inserted side.
10. Mount the tank retainer to the cart by using 1/4-20 x 1 1/4 Phillips Truss Head screw and 1/4-20 wing nut.
Figure 12
10. Install Grease Cup by sliding it in the cutout provided in the
shield.
Figure 10
Figure 13
11. For Stationary Cart Assembly: Slide grill assembly into position over holes drilled in Step 1. Secure with three screws (not
supplied). If applicable, route the gas line through the hole and
attach to the grill.
Figure 11
Page 10
B101586-4-0112
BL26P-1, SS26P-1 Patio Base
Installation Instructions
Warning: This patio base is not designed for use with an LP gas cylinder.
Warning: See your grill owner's manual for proper location, minimum clearances,
and other important safety information before proceeding with installation of this
patio post.
Verify that all parts listed on the exploded view of this manual have been included
in this Carton before beginning installation.
Caution: Use caution when handling parts, as they may contain sharp edges. Work
gloves are recommended to prevent injury.
B101586-4-0112
Page 11
Patio Base Exploded View & Parts List
3.08
8
9
2.63
Remove protective coating from stainless steel parts starting at pop rivets and verify that all parts listed in the
exploded view on this page have been included before beginning this
installation.
Caution: Use caution when handling parts, as they may contain sharp edges.
Work gloves are recommended to prevent injury.
INDEX NO.
PART NO.
DESCRIPTION
SS26P
BL26P
1
B101660
B101644
Post Assembly
2
B101760
B101760
Upper Bracket Assembly
3
B101634
B101634
Grease Cup
4
B076519
B076519
Flex Line
5
B101628
B101628
Grease Cup Holder
6
B101764
B101764
Lower Bracket Assembly
7
B074604
B074604
Cast Base
8*
-
B101596
Post Cover Plate - Black
8*
B101597
-
9
B101630
B101629
Post Cover Plate - Stainless Steel
Post Access Door
* Post Cover Plate is used only when installing R3 Series grill head onto post.
All repair part orders should be placed through your local Broilmaster dealer. To locate a dealer in your area, visit
www.broilmaster.com and click on the dealer locator. To ensure prompt and accurate service, please provide the following
information when placing a repair part order: Model Number, Part Name, Part Number, and Quantity of parts needed.
Page 12
B101586-4-0112
Patio Base Hardware Package
HEX HEAD SCREW 1/4-20 X 1 1/2
HEX HEAD BOLT 1/4-20 X 3/4
1/4 ID X 1/2 OD LOCK WASHER
1/4 ID X 5/8 OD FLAT WASHER
HEX HEAD SCREW 10 X ½ SELF DRILL
HEX HEAD SCREW 10 X 1/2
Note: Hardware shown at actual size where possible.
Description
B101586-4-0112
Quantity
Supplied
HEX HEAD SCREW 1/4-20 X 1 1/2
4
1/4 ID X 1/2 OD LOCK WASHER
4
HEX HEAD SCREW 10 X 1/2 SELF DRILL
12
HEX HEAD BOLT 1/4-20 X 3/4
4
1/4 ID X 5/8 OD FLAT WASHER
4
HEX HEAD SCREW 10 X 1/2
12
Notes
SS26P-1 Models Only
BL26P-1 Models Only
Page 13
Patio Base Installation
NOTICE: Assemble post before assembling grill.
The SS26P and BL26P Patio Bases are only for use with Broilmaster
Gas Grills. Before proceeding with installation read your Owner’s
Manual for the proper location and minimum clearances to combustible materials for your grill and in-ground post.
2. Fasten the bottom of the post to the cast base using 1/4 x 1/2
Lock Washers, and 1/4-20 x 1 1/2 Hex Head bolts. See Figure 2.
Anchor the cast iron patio base to your patio using the two holes
provided in the base. (Hardware not included)
Note: Make sure that the large rectangular cut out is facing in
the direction that you want your grill to face.
Verify that all parts listed in the exploded view of this product have
been included before beginning this installation.
Recommended Tools:
•
Drill/Driver
•
Two adjustable wrenches or a socket set
•
A medium Phillips screwdriver
•
Pipe thread sealer or Teflon tape (for gas connections)
•
Soapy water solution (to test for leaks)
1. For Stainless Steal Posts attach lower bracket assembly
to post with eight Hex Head #10-1/2” Self Drill screws. For
Black Posts, secure lower bracket assembly to post with eight
10 x 1/2 Hex Head screws. See Figure 1. Use black screws for
black posts and stainless steel screws for stainless steel posts.
NOTE: The large rectangular cut out is located at the front of the
post near the top.
Figure 2
3. Insert the stainless steel flex tube assembly into the post. The
inlet side of the gas tubing may protrude from the bottom of
the patio base or through the large circular hole in the back of
the square post. See Figure 3. Note: Do not attempt to cut or
alter the flex tube in any way.
Figure 3
4. Attach the grease cup bracket assembly to the bottom of the
grill casting and fasten with #10-24 x 3/4” bolt, 9/32 ID x 5/8
OD washer, and #10-24 wing nut. See Figure 6.
Use only the supplied grease cup or noncombustible containers for the grease cup (aluminum or tin cans). DO NOT use
combustible containers such as paper or Styrofoam cups.
Figure 1
Page 14
Figure 4
B101586-4-0112
Patio Base Installation
5. For Grill Heads other than R3 Series, continue on to Step 6.
For R3 Series Grill Heads: Bend the tabs on the Post Cover
Plate to 90° as shown in Figure 5. Two different size cover
plates are included with the R3 Series Grill Heads. Choose
the plate that will best fit your post.
Note: If using the stainless steel Post Cover Plate, bend the
tabs so they face away from the protective film. Remove the
protective film after bending the tabs.
7. Position the grill head onto the post and fasten with ¼-20 x ¾
Hex Head Screws and 1/4 x 5/8 Flat Washers. See Figure 7.
PROTECTIVE
FILM SIDE
COVER PLATE
Figure 5
Figure 7
6. For R3 Series Grill Heads: Slide the Post Cover Plate
onto the front of the post. Slide the Upper Bracket onto the
post. Secure the Post Cover Plate and Upper Bracket to the
top of the square post using four #10 – ½ Self Drill screws
for stainless steel posts and 10 x 1/2 Hex Head screws for
black posts. See Figures 5 and 6.
For Grill Heads other than R3 Series: Slide the Upper
Bracket into the post. Secure the Upper bracket to the top
of the square post using four #10 – ½ Self Drill screws. See
Figure 6.
8. Arrange with your local gas company or licensed contractor to
have a gas supply line connected to the inlet of the stainless
steel flex tube assembly. The gas supply must have a shutoff
valve that is close to the post in case of emergency and must
be shutoff when the grill is not in use.
Installing old grill head P3 or P4 to new patio post.
A B101668 kit will need to be used to cover the opening in the
post. See the instructions with the kit for further installation
information.
Figure 6
Figure 8
B101586-4-0112
Page 15
Patio Base Installation
9. Install the post access door and grease cup as shown in Figures
9 and 10.
Figure 9
STEP #1
STEP #2
STEP #3
STEP #4
NOTE: GAS LINE REMOVED FOR CLARITY
Figure 10
10. Continue assembly as directed by the Owner’s Manual packaged with the grill head.
Page 16
B101586-4-0112
BL48G-1, SS48G-1 One Piece In-Ground Post
B101652 Two Piece In-Ground Post
Installation Instructions
Warning: This in-ground post is not designed for use with an LP gas cylinder.
Warning: See your grill owner’s manual for proper location, minimum clearances, and
other important safety information before proceeding with installation of this in-ground
post.
Verify that all parts listed on the exploded view of this manual have been included in this
Carton before beginning installation.
Caution: Use caution when handling parts, as they may contain sharp edges. Work gloves
are recommended to prevent injury.
B101586-4-0112
Page 17
In-Ground Post Exploded View & Parts List
3.08
6
8
5
9
Remove protective coating from stainless steel parts starting at pop rivets and verify that all parts listed in the exploded
view on this page have been included before beginning this installation.
Caution: Use caution when handling parts, as they may contain sharp edges.
Work gloves are recommended to prevent injury.
INDEX NO.
PART NUMBER
SS48G
DESCRIPTION
B101652
BL48G
1
B101674
-
B101672
Post Assembly
2
B101760
B101760
B101760
Upper Bracket Assembly
3
B100526
B101526
B100526
Grease Cup
4
B076519
B076519
B076519
Flex Line
5
B101630
B101629
B101629
Post Access Door
6
-
B101644
-
Post Assembly
7
B100545
B100545
B100545
Grease Cup Bracket Assembly
8*
-
B101596
B101596
Post Cover Plate - Black
8*
B101597
-
-
Post Cover Plate - Stainless Steel
9
-
B101654
-
Post Extension
* Post Access Door is used only when installing R3 Series grill head onto post.
All repair part orders should be placed through your local Broilmaster dealer. To locate a dealer in your area, visit
www.broilmaster.com and click on the dealer locator. To ensure prompt and accurate service, please provide the following
information when placing a repair part order: Model Number, Part Name, Part Number, and Quantity of parts needed.
Page 18
B101586-4-0112
In-Ground Hardware Package
HEX HEAD SCREW 10 X 1/2 SELF DRILL
HEX HEAD BOLT 1/4-20 X 3/4
1/4 ID X 5/8 OD FLAT WASHER
HEX HEAD SCREW 10 X 1/2 BLACK
Note: Hardware shown at actual size where possible.
Description
B101586-4-0112
Quantity
Supplied
HEX HEAD SCREW 10 X 1/2 SELF DRILL
4
HEX HEAD BOLT 1/4-20 X 3/4
4
1/4 ID X 5/8 OD FLAT WASHER
4
HEX HEAD SCREW 10 X 1/2 BLACK
4
Notes
SS48G-1 Models Only
BL48G-1 Models Only
Page 19
In-Ground Post Assembly
NOTICE: Assemble and install patio base before assembling grill.
The SS48G and BL48G In-Ground Posts are only for use with
Broilmaster Gas Grills. Before proceeding with installation read
your Owner’s Manual for the proper location and minimum clearances to combustible materials for your grill and in-ground post.
Verify that all parts listed in the exploded view of this product have
been included before beginning this installation.
Recommended Tools:
•
•
•
•
•
Drill/Driver
Two adjustable wrenches or a socket set
A medium Phillips screwdriver
Pipe thread sealer or Teflon tape (for gas connections)
Soapy water solution (to test for leaks)
1. For two piece in-ground post using eight 10 x 1/2 Hex Head
screws. Use black screws for black posts. For this application, use
top set of holes in post assembly. See Figure 1.
NOTE: For SS48G and BL48G models, it is an option
to purchase a Post Extension through your Broilmaster Dealer to increase Post Assembly length
.
NOTE: The extension is available on the 48” post for applications that may need more height.
The gas supply line should be trenched at least 10 inches
below the surface of the ground to prevent damage from digging.
CAUTION: The gas supply line must be regulated
(In the case of Natural gas that means connected after your
gas meter and regulator) and that you have an easily accessible shut-off valve.
At the access door connect a 3/8” flare coupling (not supplied
by Empire) to the gas supply line and stainless steel tubing.
Position the tubing in the top notch of the post. Bend the flex
tube at the top end to match the Feed Line of the grill valve.
See Figure 2.
Note: Use pipe thread sealant or Teflon tape at the threads
of each connection being careful to not allow any of these
materials into the flare seat. Test for gas leaks as directed by
the grill’s Owners Manual
Note: Do not attempt to cut or alter the stainless steel flex
tube assembly in any way.
Note: For R Series Grills, a Cover Plate will be supplied, so
the Flex Line will have to go through the hole on the cover
plate before mounting the Grill bottom.
Carefully lower the in-ground post into the hole using the following guidelines:
•
The rectangular cut-out is located near the TOP of the
post and should be above ground after installation. See
Figure 1.
•
The rectangular cut-out must face in the SAME direction
as the front of the grill.
•
Hole depth and post measurements should be checked
to ensure desired height.
Note: Make any adjustments at this time.
24 3/4”
ABOVE GRADE
Figure 1
2. Dig a posthole approximately 12” in diameter and 28 3/4” in
depth at the desired grill location.
Note: “Normal Installation” height is achieved when the
top of the 48” post is 24 3/4” above ground. This height
provides a cooking surface height of approximately
34” above ground when grids are placed in the high level.
Page 20
Figure 2
Prepare concrete or a standard pre-mix according to the manufacturer’s package directions. Position the 48” post in the
center of the hole. A level should be used when aligning the
post to achieve precise vertical alignment. Hold the post in
place while pouring the concrete mixture into the hole around
the post.
B101586-4-0112
In-Ground Post Assembly
3. Attach the grease cup bracket assembly to the bottom of the
grill casting and fasten with #10-24 x 3/4” bolt, 9/32 ID x 5/8
OD washer, and #10-24 wing nut. See Figure 6.
Use only the supplied grease cup or noncombustible containers for the grease cup (aluminum or tin cans). DO NOT use
combustible containers such as paper or Styrofoam cups.
Note:
Grill top comes assembled to the bottom. For ease of assembly, remove grill top.
6.
Place the grill bottom on top of the post and secure the
grill bottom to the post by placing four 1/4-20 x 3/4 Hex Head
screws and 1/4 x 5/8 Flat Washers in the threaded inserts that are
in the upper bracket. See Figure 6.
Figure 3
4. For Grill Heads other than R3 Series, continue on to
Step 5.
For R3 Series Grill Heads: Bend the tabs on the Post Cover
Plate to 90° as shown in Figure 4. Two different size cover
plates are included with the R3 Series Grill Heads. Choose
the plate that will best fit your post.
Note: If using the stainless steel Post Cover Plate, bend the
tabs so they face away from the protective film. Remove the
protective film after bending the tabs.
Figure 6
Installing old grill head P3 or P4 to new patio post.
A B101668 kit will need to be used to cover the opening in the
post. See the instructions with the kit for further installation
information.
PROTECTIVE
FILM SIDE
COVER PLATE
Figure 4
5. For R3 Series Grill Heads: Slide the Post Cover
Plate onto the front of the post. Slide the Upper Bracket onto the post. Secure the Post Cover Plate and Upper Bracket to the top of the square post using four
#10 – ½ Hex Head screws. See Figure 5.
For Grill Heads other than R3 Series: Slide the Upper
Bracket into the post. Secure the Upper bracket to the top
of the square post using four #10 – ½ screws. See Figure 5.
Figure 7
B101586-4-0112
Figure 5
Page 21
In-Ground Post Assembly
7. Arrange with your local gas company or licensed contractor to
have a gas supply line connected to the inlet of the stainless
steel flex tube assembly. The gas supply must have a shutoff
valve that is close to the post in case of emergency and must
be shutoff when the grill is not in use. See Figure 8.
The grill and its individual shutoff valves must be disconnected
from the gas supply piping system during any pressure testing
of that system at test pressures in excess of 1/2 PSIG. The
grill must be isolated from the gas supply piping system by
closing its individual manual shutoff valves during any pressure testing of the gas supply piping system at test pressures
equal to or less than 1/2 PSIG.
STEP #1
STEP #2
STEP #3
STEP #4
WARNING: DO NOT SUPPLY LP GAS TO A GRILL DESIGNED FOR NATURAL GAS OR NATURAL GAS TO A
GRILL DESIGNED FOR LP GAS.
Gas leak tests should be completed as directed in the grill
Owner’s Manual.
Completely fill remaining hole with soil.
24 3/4”
ABOVE GRADE
NOTE: GAS LINE REMOVED FOR CLARITY
Figure 10
9. Continue assembly as directed by the Owner’s Manual packaged with the grill head.
Figure 8
8. Install the post access door and grease cup as shown in Figures 9 and 10.
Test for gas leaks as directed by the grill’s Owners Manual. The
grill and its individual shutoff valves must be disconnected from
the gas supply piping system during any pressure testing of
that system at test pressures in excess of 1/2 PSIG. The grill
must be isolated from the gas supply piping system by closing
its individual manual shutoff valves during any pressure testing
of the gas supply piping system at test pressures equal to or
less than 1/2 PSIG.
WARNING: DO NOT SUPPLY LP GAS TO A GRILL DESIGNED FOR NATURAL GAS OR NATURAL GAS TO A GRILL
DESIGNED FOR LP GAS.
Gas leak tests should be completed as directed in the grill
owner’s manual.
Figure 9
Page 22
B101586-4-0112
PCB1-2 / DCB1-2
B101586-4-0112
Page 23
BROILMASTER®
A Division of Empire Comfort Systems, Inc.
918 Freeburg Ave.
Belleville, Illinois 62220
Phone: 1-800-851-3153
FAX: 1-800-443-8648
Visit our web site at www.broilmaster.com
Retain Owner’s Manual for Future Reference.
Page 24
B101586-4-0112
Download PDF

advertising