Brother 8060 All in One Printer User Manual

Setting Up
the machine
Windows®
USB
Step 1
Windows®
Parallel
Setting Up the machine
Step 2
Windows
NT® 4.0
Parallel
USB
Network
Network
Administrators
Keep this “Quick Setup Guide”, User’s Guide and supplied CD-ROM in a convenient place for
quick and easy reference at all times.
Windows®
Network
Setup is Complete!
Macintosh®
Installing the Drivers & Software
Installing the Drivers & Software
Macintosh®
Quick Setup Guide
DCP-8060
DCP-8065DN
Before you can use the machine, you must set up the hardware and install the software.
Please read this “Quick Setup Guide” for the correct setup procedure and installation
instructions.
Version A
Warning
Caution
Improper Setup
Note
User’s Guide
Warnings tell you
what to do to prevent
possible personal
injury.
Cautions specify
procedures you
must follow or avoid
to prevent possible
damage to the
machine or other
objects.
Improper Setup
icons alert you to
devices and
operations that are
not compatible with
the machine.
Notes tell you how
you should respond
to a situation that
may arise or give
tips about how the
current operation
works with other
features.
Indicates reference
to the User’s Guide.
■ Getting Started
Carton Components
1
2
8
7
Quick Setup Guide
3
4
6
CD-ROMs
For Windows®
For Macintosh®
5
AC Power Cord
1. Automatic Document Feeder (ADF)
2. Control Panel
3. Face-down Output Tray
Support Flap (Support Flap)
5. Paper Tray
6. Power Switch
7. Document Cover
8. ADF Document Output Support Flap
4. Front Cover
Drum Unit Assembly
(including Toner
Cartridge)
Carton components may differ from one country to another.
Save all packing materials and the carton.
Austraria & New Zealand users:
Hong Kong, Malaysia & Singapore users:
The mains plug supplied with this machine is a grounded three pin plug. Make sure that the AC socket will
accept this grounded three pin plug. This machine must be grounded, If in doubt, call a qualified electrician.
Philipine & Thailand users:
The mains plug supplied with this machine is a side grounded two pin plug. Make sure that
the AC socket will accept this side grounded two pin plug. This machine must be grounded,
If in doubt, call a qualified electrician.
■ To ensure safe operation the supplied plug must be inserted only into a standard power outlet that is
properly grounded through the standard electrical wiring. None grounded equipment may cause an
electrical shock hazard, and may cause excessive electrical noise radiation.
■ The interface cable is not a standard accessory. Please purchase the appropriate interface cable for
the interface you intend to use (Parallel, USB or Network).
■ Do NOT connect the interface cable at this time. Connecting the interface cable is done during the
software installation process.
■ USB interface cable
Please make sure you use a USB 2.0 interface cable that is no longer than 2.0 meters.
When you use a USB cable, make sure you connect it to the USB port of your computer and not to a
USB port on a keyboard or non-powered USB hub.
■ Parallel interface cable
Please make sure you use a Parallel interface cable that is no longer than 2.0 meters.
Use a shielded interface cable that is IEEE 1284-compliant.
■ Network cable (DCP-8065DN only)
Use a straight-through Category5 (or greater) twisted-pair cable for 10BASE-T or 100Base-TX Fast
Ethernet Network.
1
Control Panel
DCP-8060
1
9
2
3
4
8
7
5
6
DCP-8065DN
1
9
2
3
4
8
7
5
6
1
Status LED
2
LCD (Liquid Crystal Display)
3
Menu keys
4
Dial Pad
5
Stop/Exit key
6
Start key
7
Copy keys
8
Scan key
9
Print keys
For the details of the control panel, see “Control panel overview” in Chapter 1 of the User’s Guide.
2
Table of Contents
Setting Up the machine
Step 1
1.
2.
3.
4.
5.
Step 2
Install the Drum Unit and Toner Cartridge Assembly .................................... 4
Load Paper in the Paper Tray .......................................................................... 5
Release the Scanner Lock ................................................................................ 6
Connect the Power Cord .................................................................................. 6
Setting the LCD Contrast ................................................................................. 7
Installing the Drivers & Software
Supplied CD-ROM “MFL-Pro Suite” ................................................................................ 8
For USB Interface Cable Users
(For Windows® 98/98SE/Me/2000 Professional/XP/XP Professional x64 Edition) .... 10
For Parallel Interface Cable Users
(For Windows® 98/98SE/Me/2000 Professional/XP/XP Professional x64 Edition) .... 12
For Windows NT® Workstation Version 4.0 Users ......................................................15
For Network Interface Cable Users (DCP-8065DN only)
(For Windows® 98/98SE/Me/NT/2000 Professional/XP/XP Professional x64 Edition) ...17
For USB Interface Cable Users ......................................................................................20
■ For Mac OS® 9.1 to 9.2 ......................................................................................20
■ For Mac OS® X 10.2.4 or greater ....................................................................... 22
For Network Interface Cable Users (DCP-8065DN only) ............................................. 25
■ For Mac OS® 9.1 to 9.2 ......................................................................................25
■ For Mac OS® X 10.2.4 or greater ....................................................................... 27
■ For Network Users and Administrators (DCP-8065DN only)
BRAdmin Professional configuration utility (For Windows® users) .......................... 30
BRAdmin Light configuration utility (For Mac OS® X users) ...................................... 32
■ Options and Consumables
Options ............................................................................................................................33
Replacement Consumables ...........................................................................................33
3
Step 1
Setting Up the machine
1 Install the Drum Unit and Toner Cartridge Assembly
Do not connect the interface cable.
Connecting the interface cable is
done during the software
installation process.
1
Unpack the drum unit and toner cartridge
assembly.
3
Gently rock it from side to side several times
to distribute the toner evenly inside the
cartridge.
4
Put the drum unit and toner cartridge into
the machine so that it clicks into place.
5
Close the front cover of the machine.
Open the front cover by pressing the front
cover release button (1).
(1)
4
2
Pull the paper tray completely out of the
machine.
4
Put paper in the paper tray.
Check that the paper is flat in the tray and
below the maximum paper mark (1).
Windows®
USB
1
Setting Up
the machine
2 Load Paper in the Paper Tray
While pressing the blue paper guide release
lever (1), slide the adjusters to fit the paper
size. Check that the guides are firmly in the
slots.
5
Windows
NT® 4.0
Parallel
2
Windows®
Parallel
(1)
Put the paper tray firmly back into the
machine and unfold the support flap (1)
before you use the machine.
Windows®
Network
(1)
Macintosh®
Network
Fan the stack of paper well to avoid paper
jams and misfeeds.
For details on supported paper
specifications, see “Acceptable paper and
other media” in Chapter 2 of the User’s
Guide.
Network
Administrators
3
Macintosh®
USB
(1)
5
Step 1
3
1
Setting Up the machine
Release the Scanner
Lock
Push the lever (1) in the direction shown to
unlock the scanner.
(The gray scanner lock lever is located at
the back left side, under the document
cover (2).)
4 Connect the Power Cord
Do not connect the Parallel or USB
cable yet.
1
Make sure that the power switch is off.
Connect the AC power cord to the machine.
2
Plug the AC power cord into an AC outlet.
Turn the power switch on.
(2)
(1)
If Scanner Locked appears on the LCD,
immediately release the scanner lock and
press Stop/Exit. (See “Release the Scanner
Lock” on page 6.)
6
Setting Up
the machine
5 Setting the LCD Contrast
You can change the contrast to help the LCD look
lighter or darker.
Press Menu.
Press 1.
Windows®
USB
Press 6.
Macintosh®
Network
Macintosh®
USB
Windows®
Network
Windows
NT® 4.0
Parallel
Windows®
Parallel
Press
to increase the contrast.
—OR—
Press
to decrease the contrast.
Press OK.
Network
Administrators
1
2
3
4
Go to the next page to
install the drivers & software
7
Step 2
Installing the Drivers & Software
Supplied CD-ROM “MFL-Pro Suite”
The CD-ROM includes the following items:
Install MFL-Pro Suite
You can install the MFL-Pro Suite and multifunction
drivers.
Start Here OS 9.1-9.2
You can install the printer driver, scanner driver and
Presto!® PageManager® for Mac OS® 9.1 - 9.2.
Install Optional Applications
You can install additional MFL-Pro Suite software
utilities.
Start Here OSX
You can install the MFL-Pro Suite that includes the
printer driver, scanner driver and the Brother
ControlCenter2 for Mac OS® 10.2.4 or greater. You
can also install Presto!® PageManager® to add OCR
capability to the Brother ControlCenter2 and easily
scan, share and organize photos and documents.
Documentation
View the User’s Guide and other documents in PDF
format (Viewer included). The User’s Guide on the
CD-ROM includes the Software and Network User’s
Guide for features available when connected to a
computer (e.g. printing, scanning and networking
details).
.
On-Line Registration
You will be pointed to the Brother Product
Registration Web page for quick registration of your
machine.
Brother Solutions Center
Brother contact information and web site links offering
the latest news and support information.
Repair MFL-Pro Suite
(For USB and Parallel cable users only)
If you experience errors while installing the MFL-Pro
Suite, you can use this function to automatically repair
and re-install the software.
MFL-Pro Suite includes Printer Driver,
Scanner Driver, Brother ControlCenter2,
ScanSoft® PaperPort® SE with OCR and
True Type® fonts.
PaperPort ® SE is a document management
application for viewing scanned documents.
8
Readme.html
You can get important information and
troubleshooting tips.
Documentation
View the User’s Guide and other document in PDF
format (Viewer included). The User’s Guide on the
CD-ROM includes the Software and Network User’s
Guide for features available when connected to a
computer (e.g. printing, scanning and networking
details).
Brother Solutions Center
You can access the Brother Solutions Center, a Web
site offering information about your Brother product
including FAQs, User’s Guides, Driver updates and
Tips for using your machine.
On-Line Registration
You will be pointed to the Brother Product
Registration Web Page for quick registration of your
machine.
Step 2
Installing the Drivers & Software
Setting Up
the machine
Follow the instructions on this page for your operating system and interface cable.
For the latest drivers and to find the best solution for your problem or question, access the Brother Solutions
Center directly from the driver or go to http://solutions.brother.com
Windows®
USB
USB Interface Cable Users .......................................... Go to page 10
(For Windows® 98/98SE/Me/2000 Professional/XP/XP Professional x64 Edition)
Windows®
Parallel
Parallel Interface Cable Users ..................................... Go to page 12
(For Windows® 98/98SE/Me/2000 Professional/XP/XP Professional x64 Edition)
Windows
NT® 4.0
Parallel
Windows NT® Workstation Version 4.0 Users........... Go to page 15
(For Parallel Interface Cable Users)
Windows®
Network
Network Interface Cable Users.................................... Go to page 17
(DCP-8065DN only)
Macintosh®
USB
USB Interface Cable Users
■ For Mac OS® 9.1 to 9.2 ............................................. Go to page 20
■ For Mac OS® X 10.2.4 or greater ............................. Go to page 22
Network
Administrators
Macintosh®
Network
Network Interface Cable Users (DCP-8065DN only)
■ For Mac OS® 9.1 to 9.2 ............................................. Go to page 25
■ For Mac OS® X 10.2.4 or greater ............................. Go to page 27
For Network Users and Administrators...................... Go to page 30
9
Step 2
Installing the Drivers & Software
For USB Interface Cable Users
(For Windows® 98/98SE/Me/2000 Professional/XP/XP Professional x64 Edition)
Make sure that you have finished the instructions from Step 1 “Setting Up
the machine” on pages 4 - 7.
Please close any applications running before
installing the MFL-Pro Suite.
1
5
After reading and accepting the ScanSoft®
PaperPort® SE License Agreement, click
Yes.
Switch off the machine and disconnect the
machine from the power socket (and from
your computer, if you have already
connected an interface cable).
The installation of PaperPort® SE will
automatically start and is followed by the
installation of MFL-Pro Suite.
2
Turn on your computer.
(For Windows® 2000 Professional/XP/
XP Professional x64 Edition, you must be
logged on with Administrator rights.)
3
Put the supplied CD-ROM for Windows®
into your CD-ROM drive. If the model name
screen appears, choose your machine. If
the language screen appears, choose your
language.
4
The CD-ROM main menu will appear.
Click Install MFL-Pro Suite.
6
When the Brother MFL-Pro Suite Software
License Agreement window appears, click
Yes if you agree to the Software License
Agreement.
7
Choose Standard (DCP-8060) or Local
Connection (DCP-8065DN), and then click
Next. The installation continues.
(DCP-8060)
If this window does not appear, use Windows®
Explorer to run the setup.exe program from
the root folder of the Brother CD-ROM.
10
(DCP-8065DN)
If you want to install the PS driver (BR-Script 3
printer driver), choose Custom Install and
then follow the on-screen instructions. When
the Select Components screen appears,
check PS Printer Driver, and then continue
following the on-screen instructions.
Setting Up
the machine
It will take a few seconds for the installation
screens to appear.
The installation of the Brother drivers will
automatically start. The installation screens
appear one after another. Please wait, it will
take a few seconds for all the screens to
appear.
When this screen appears, connect the
USB interface cable to your PC, and then
connect it to the machine.
(For Windows® XP)
Windows®
USB
8
0
When the On-Line Registration screen is
displayed, make your selection and follow
the on-screen instructions.
A
Click Finish to restart your computer.
(After restarting the computer, for
Windows® 2000 Professional/XP/
XP Professional x64 Edition, you must be
logged on with Administrator rights.)
(For Windows® 98/98SE/Me/2000)
Installing the Drivers & Software
DO NOT try to cancel any of the
screens during this installation.
DO NOT connect the machine to a
USB port on a keyboard or a nonpowered USB hub. Brother
recommends that you connect the
machine directly to your computer.
Plug in the power cord and turn on the
machine.
After restarting the computer, the Installation
Diagnostics will run automatically. If the
installation is unsuccessful, the installation
results window will be shown. If the
Installation Diagnostics shows a failure,
please follow the on-screen instruction or read
on-line help and FAQs in
Start/All Programs (Programs)/Brother/
MFL-Pro Suite DCP-XXXX (where XXXX is
your model name).
Network
Administrators
9
The MFL-Pro Suite (including printer
driver and scanner driver) has been
installed and the installation is now
complete.
11
Step 2
Installing the Drivers & Software
For Parallel Interface Cable Users
(For Windows® 98/98SE/Me/2000 Professional/XP/XP Professional x64 Edition)
Make sure that you have finished the instructions from Step 1 “Setting Up
the machine” on pages 4 - 7.
Please close any applications running before
installing the MFL-Pro Suite.
1
5
After reading and accepting the ScanSoft®
PaperPort® SE License Agreement, click
Yes.
Switch off the machine and disconnect the
machine from the power socket (and from
your computer, if you have already
connected an interface cable).
The installation of PaperPort® SE will
automatically start and is followed by the
installation of MFL-Pro Suite.
2
Turn on your computer.
(For Windows® 2000 Professional/XP/
XP Professional x64 Edition, you must be
logged on with Administrator rights.)
3
Put the supplied CD-ROM for Windows®
into your CD-ROM drive. If the model name
screen appears, choose your machine. If
the language screen appears, choose your
language.
4
The CD-ROM main menu will appear.
Click Install MFL-Pro Suite.
6
When the Brother MFL-Pro Suite Software
License Agreement window appears, click
Yes if you agree to the Software License
Agreement.
7
Choose Standard (DCP-8060) or Local
Connection (DCP-8065DN), and then click
Next. The installation continues.
(DCP-8060)
If this window does not appear, use Windows®
Explorer to run the setup.exe program from
the root folder of the Brother CD-ROM.
12
(DCP-8065DN)
If you want to install the PS driver (BR-Script 3
printer driver), choose Custom Install and
then follow the on-screen instructions. When
the Select Components screen appears,
check PS Printer Driver, and then continue
following the on-screen instructions.
When this screen appears, connect the
parallel interface cable to your PC, and then
connect it to the machine.
0
Setting Up
the machine
8
For Windows® 98/98SE/Me/
2000 Professional users, click Next.
(For Windows® XP)
(For Windows® 98/98SE/Me/2000)
Windows®
Parallel
Windows® XP users should wait for a while;
installation of the Brother drivers will start
automatically. The installation screens
appear one after another.
A
When the On-Line Registration screen is
displayed, make your selection and follow
the on-screen instructions.
B
When the following screen appears, click
Finish and wait as the PC restarts
Windows® and continues the installation.
DO NOT plug in the power cord
before connecting the parallel
interface cable. It may cause
damage to your machine. Brother
recommends that you connect the
machine directly to your computer.
Plug in the power cord and turn on the
machine.
Network
Administrators
9
Installing the Drivers & Software
DO NOT try to cancel any of the
screens during this installation.
Continued...
13
Step 2
Installing the Drivers & Software
For Parallel Interface Cable Users
(For Windows® 98/98SE/Me/2000 Professional/XP/XP Professional x64 Edition)
C
After the computer restarts, the installation
of the Brother drivers will automatically start.
Follow the instructions on the screen.
(For Windows® 2000 Professional/XP/
XP Professional x64 Edition, you must be
logged on with Administrator rights.)
After restarting the computer, the Installation
Diagnostics will run automatically. If the
installation is unsuccessful, the installation
results window will be shown. If the
Installation Diagnostics shows a failure,
please follow the on-screen instruction or read
on-line help and FAQs in
Start/All Programs (Programs)/Brother/
MFL-Pro Suite DCP-XXXX (where XXXX is
your model name).
The MFL-Pro Suite (including printer
driver and scanner driver) has been
installed and the installation is now
complete.
14
Setting Up
the machine
For Windows NT® Workstation Version 4.0 Users
Make sure that you have finished the instructions from Step 1 “Setting Up
the machine” on pages 4 - 7.
Switch off the machine and disconnect the
machine from the power socket.
2
Turn on your computer.
You must be logged on with Administrator
rights.
Put the supplied CD-ROM for Windows®
into your CD-ROM drive. If the model name
screen appears, choose your machine. If
the language screen appears, select your
language.
6
The CD-ROM main menu will appear.
Click Install MFL-Pro Suite.
Windows®
Parallel
1
5
3
Connect the parallel interface cable to your
computer, and then connect it to the
machine.
If this window does not appear, use Windows®
Explorer to run the setup.exe program from
the root folder of the Brother CD-ROM.
7
After reading and accepting the ScanSoft®
PaperPort® SE License Agreement, click
Yes.
Installing the Drivers & Software
DO NOT plug in the power cord
before connecting the parallel
interface cable. It may cause
damage to your machine.
Windows
NT® 4.0
Parallel
Please close any applications running before
installing the MFL-Pro Suite.
Brother recommends that you connect the
machine directly to your computer.
Plug in the power cord and turn on the
machine.
The installation of PaperPort® SE will
automatically start and is followed by the
installation of MFL-Pro Suite.
Network
Administrators
4
Continued...
15
Step 2
Installing the Drivers & Software
For Windows NT® Workstation Version 4.0 Users
8
When the Brother MFL-Pro Suite Software
License Agreement window appears, click
Yes if you agree to the Software License
Agreement.
9
Choose Standard (DCP-8060) or Local
Connection (DCP-8065DN), and then click
Next. The installation continues.
(DCP-8060)
(DCP-8065DN)
If you want to install the PS driver (BR-Script 3
printer driver), choose Custom Install and
then follow the on-screen instructions. When
the Select Components screen appears,
check PS Printer Driver, and then continue
following the on-screen instructions.
0
16
When the On-Line Registration screen is
displayed, make your selection and follow
the on-screen instructions.
A
Click Finish and wait as the PC restarts
Windows® and continues the installation.
(You must be logged on with Administrator
rights.)
After restarting the computer, the Installation
Diagnostics will run automatically. If the
installation is unsuccessful, the installation
results window will be shown. If the
Installation Diagnostics shows a failure,
please follow the on-screen instruction or read
on-line help and FAQs in Start/Programs/
Brother/MFL-Pro Suite DCP-XXXX (where
XXXX is your model name).
The MFL-Pro Suite (including printer
driver and scanner driver) has been
installed and the installation is now
complete.
For Network Interface Cable Users (DCP-8065DN only)
Setting Up
the machine
(For Windows® 98/98SE/Me/NT/2000 Professional/XP/XP Professional x64 Edition)
Make sure that you have finished the instructions from Step 1 “Setting Up
the machine” on pages 4 - 7.
1
Switch off and disconnect the machine from
the power socket.
2
Connect the network cable to the machine,
and then connect it to a free port on your
hub.
6
The CD-ROM main menu will appear.
Click Install MFL-Pro Suite.
4
Turn on your computer.
(For Windows® 2000 Professional/XP/
XP Professional x64 Edition/
Windows NT® 4.0, you must be logged on
with Administrator rights.) Close any
applications running before installing the
MFL-Pro Suite.
7
After reading and accepting the ScanSoft®
PaperPort® SE License Agreement, click
Yes.
The installation of PaperPort® SE will
automatically start and is followed by the
installation of MFL-Pro Suite.
8
Windows
NT® 4.0
Parallel
Plug in the power cord and turn on the
machine.
Windows®
Network
3
Installing the Drivers & Software
If this window does not appear, use Windows®
Explorer to run the setup.exe program from
the root folder of the Brother CD-ROM.
When the Brother MFL-Pro Suite Software
License Agreement window appears, read
the agreement, then click Yes if you agree
to its terms.
Before installation, if you are using Personal
Firewall software, disable it. Once you are
sure that you can print after the installation,
re-start your Personal Firewall software.
Put the supplied CD-ROM for Windows®
into your CD-ROM drive. If the model name
screen appears, choose your machine. If
the language screen appears, select your
language.
Network
Administrators
5
Continued...
17
Step 2
Installing the Drivers & Software
For Network Interface Cable Users (DCP-8065DN only)
(For Windows® 98/98SE/Me/NT/2000 Professional/XP/XP Professional x64 Edition)
9
Choose Network Connection and then
click Next.
If you want to install the PS driver (Brother’s
BR-Script Driver), choose Custom Install and
then follow the on-screen instructions. When
the Select Components screen appears,
check PS Printer Driver, and then continue
following the on-screen instructions.
0
B
If the machine is not yet configured for use
on your network, the following screen
appears.
Click OK. The Configure IP Address
window will appear. Enter the IP address
information appropriate to your network by
following the on-screen instructions.
C
When the On-Line Registration screen is
displayed, make your selection and follow
the on-screen instructions.
D
Click Finish to restart your computer.
(For Windows® 2000 Professional/XP/
XP Professional x64 Edition/
Windows NT® 4.0, you must be logged on
with Administrator rights.)
The installation of the Brother drivers will
automatically start. The installation screens
appear one after another. Please wait, it will
take a few seconds for all the screens to
appear.
DO NOT try to cancel any of the
screens during this installation.
A
If the machine is configured for your
network, select your machine from the list
and then click Next.
This window will not appear if there is only one
of this Brother model connected on the
network, it will be selected automatically.
18
The MFL-Pro Suite (including network
printer driver and network scanner
driver) has been installed and the
installation is now complete.
Setting Up
the machine
1
2
5
5 If you still have trouble with your network
connection, click the Add button.
6 To add port 137 for network scanning,
enter the information below:
1) In Description of service: - Enter any
description, for example “Brother Port”
(without the inverted commas).
2) In Name or IP address (for example
192.168.0.12) of the computer
hosting this service on your
network: - Enter “Localhost” (without
the inverted commas).
3) In External Port Number for this
service: - Enter “137” (without the
inverted commas).
4) In Internal Port number for this
service: - Enter “137” (without the
inverted commas).
5) Make sure UDP is selected.
6) Click OK.
7 Make sure that the new settings are
added and are checked, and then click
OK.
Windows®
Network
3
4
■ For network installations, the Repair
MFL-Pro Suite selection from the main
menu is not supported.
■ Network Scanning, Network Remote Setup,
Network PC-FAX Receiving are not
supported in Windows NT® 4.0.
■ For configuration of advanced network
functions such as LDAP and Scan to FTP,
see the Software and Network Users
Guides located on the CD-ROM.
Network
Administrators
3 Click the Add button.
4 To add port 54925 for network scanning,
enter the information below:
1) In Description of service: - Enter any
description, for example “Brother
Scanner” (without the inverted
commas).
2) In Name or IP address (for example
192.168.0.12) of the computer
hosting this service on your
network: - Enter “Localhost” (without
the inverted commas).
3) In External Port Number for this
service: - Enter “54925” (without the
inverted commas).
4) In Internal Port number for this
service: - Enter “54925” (without the
inverted commas).
5) Make sure UDP is selected.
6) Click OK.
Installing the Drivers & Software
■ After restarting the computer, the
Installation Diagnostics will run
automatically. If the installation is
unsuccessful, the installation results
window will be shown. If the Installation
Diagnostics shows a failure, please follow
the on-screen instruction or read on-line
help and FAQs in Start/All Programs
(Programs)/Brother/MFL-Pro Suite
DCP-XXXX (where XXXX is your model
name).
■ Once you are sure that you can print after
the installation, restart your Firewall
software.
■ Firewall settings on your PC may reject the
necessary network connection for Network
Scanning.
Follow the instructions below to configure
your Windows Firewall. If you are using a
personal Firewall software, see the User's
Guide for your software or contact the
software manufacturer.
■ Windows® XP SP2 users:
1 Click the Start button, Control Panel
and then Windows Firewall.
Make sure that Windows Firewall on the
General tab is set to On.
2 Click the Advanced tab and Settings...
button.
19
Step 2
Installing the Drivers & Software
For USB Interface Cable Users
For Mac OS® 9.1 to 9.2
Make sure that you have finished the instructions from Step 1 “Setting Up
the machine” on pages 4 - 7.
1
20
Switch off the machine and disconnect the
machine from the power socket (and from
the Macintosh®, if you have already
connected an interface cable).
2
3
Turn on your Macintosh®.
4
Double-click the Start Here OS 9.1-9.2 icon
to install the printer and scanner drivers. If
the language screen appears, choose your
language.
5
Click MFL-Pro Suite to install.
6
Follow the on-screen instructions, and
restart your Macintosh®.
7
Connect the USB interface cable to your
Macintosh®, and then connect it to the
machine.
DO NOT connect the machine to a
USB port on a keyboard or a nonpowered USB hub.
Insert the supplied CD-ROM for Macintosh®
into your CD-ROM drive.
8
Plug in the power cord and turn on the
machine.
9
From the Apple® menu, click Chooser.
Setting Up
the machine
0
Click the Brother Laser icon.
On the right side of the Chooser, choose
the machine to which you want to print.
Close the Chooser.
You can easily scan, share and organize
photos and documents using Presto!®
PageManager®.
USB
To install Presto!® PageManager®, click the
Presto! PageManager icon and follow the
on-screen instructions.
Presto!® PageManager® has been
installed and the installation is now
complete.
Network
Administrators
A
Macintosh®
ControlCenter2 is not supported in
Mac OS® 9.1 to 9.2.
Installing the Drivers & Software
The MFL-Pro Suite, printer driver and
scanner driver have been installed.
21
Step 2
Installing the Drivers & Software
For USB Interface Cable Users
For Mac OS® X 10.2.4 or greater
Make sure that you have finished the instructions from Step 1 “Setting Up
the machine” on pages 4 - 7.
For Mac OS® X 10.2.0 to 10.2.3 users,
upgrade to Mac OS® X 10.2.4 or greater.
(For the latest information for Mac OS® X,
visit http://solutions.brother.com)
1
22
5
Click MFL-Pro Suite to install.
6
Follow the on-screen instructions, and
restart your Macintosh®.
7
After the DeviceSelector window appears,
connect the USB interface cable to your
Macintosh® and then to the machine.
Switch off the machine and disconnect the
machine from the power socket (and from
the Macintosh®, if you have already
connected an interface cable).
2
3
Turn on your Macintosh®.
4
Double-click the Start Here OSX icon to
install the drivers and MFL-Pro Suite. If the
language screen appears, choose your
language.
Insert the supplied CD-ROM for Macintosh®
into your CD-ROM drive.
The DeviceSelector window will not appear if
you have also connected a USB interface
cable to the machine before restarting your
Macintosh® or if you are overwriting a
previously installed version of the Brother
software. If you encounter this problem
continue with the installation but skip step 9.
You should choose your Brother machine
from the Model pull-down list in the main
screen of ControlCenter2. (For details, see the
Software User’s Guide on the CD-ROM).
DO NOT connect the machine to a
USB port on a keyboard or a nonpowered USB hub.
Setting Up
the machine
Double-Click the Utilities folder.
B
Double-Click the Print Setup Utility icon.
C
9
Click Add.
Choose USB and then click OK.
For Mac OS® X 10.2.4 to 10.3.x users
➝ Go to D
Click Go, then choose Application.
For Mac OS® X 10.4 users ➝ Go to E
Network
Administrators
0
USB
For Mac OS® 10.2.x users, double-click the
Print Center icon.
Installing the Drivers & Software
Plug in the power cord and turn on the
machine.
Macintosh®
8
A
Continued...
23
Step 2
Installing the Drivers & Software
For USB Interface Cable Users
D
Choose USB.
E
Choose your model name, and then click
Add.
For Mac OS® X 10.2.4 to 10.3 users:
G
To install Presto!® PageManager®, click the
Presto! PageManager icon and follow the
on-screen instructions.
When Presto!® PageManager® is installed
OCR capability is added to the Brother
ControlCenter2. You can easily scan, share,
and organize photos and documents using
Presto!® PageManager®.
Presto!® PageManager® has been
installed and the installation is now
complete.
For Mac OS® X 10.4 or greater users:
F
Click Printer Setup Utility, then choose
Quit Printer Setup Utility.
The MFL-Pro Suite, printer driver,
scanner driver and Brother
ControlCenter2 have been installed.
24
Setting Up
the machine
For Network Interface Cable Users (DCP-8065DN only)
For Mac OS® 9.1 to 9.2
Connect the network interface cable to the
machine, and then connect it to a free port
on your hub.
8
Plug in the power cord and turn on the
machine.
9
From the Apple® menu, click Chooser.
Turn on your Macintosh®.
Insert the supplied CD-ROM for Macintosh®
into your CD-ROM drive.
Double-click the Start Here OS 9.1-9.2 icon
to install the printer driver. If the language
screen appears, choose your language.
USB
7
Network
5
Follow the on-screen instructions, and
restart your Macintosh®.
Click MFL-Pro Suite to install.
Network
Administrators
4
6
Macintosh®
2
3
Switch off the machine and disconnect the
machine from the power socket (and from
the Macintosh®, if you have already
connected an interface cable).
Macintosh®
1
Installing the Drivers & Software
Make sure that you have finished the instructions from Step 1 “Setting Up
the machine” on pages 4 - 7.
Continued...
25
Step 2
Installing the Drivers & Software
For Network Interface Cable Users (DCP-8065DN only)
0
Click the Brother Laser (IP) icon, and then
choose BRN_XXXXXX.
Close the Chooser.
XXXXXX are the last six digits of the Ethernet
address.
The MFL-Pro Suite and printer driver
have been installed.
ControlCenter2 and Network Scanning are not
supported in Mac OS® 9.1 to 9.2.
A
To install Presto!® PageManager®, click the
Presto! PageManager icon and follow the
on-screen instructions.
You can easily scan, share and organize
photos and documents using Presto!®
PageManager®.
Presto!® PageManager® has been
installed and the installation is now
complete.
26
Setting Up
the machine
For Network Interface Cable Users (DCP-8065DN only)
For Mac OS® X 10.2.4 or greater
Make sure that you have finished the instructions from Step 1 “Setting Up
the machine” on pages 4 - 7.
4
Double-click the Start Here OSX icon to
install the printer and scanner drivers. If the
language screen appears, choose your
language.
5
Click MFL-Pro Suite to install.
6
The DeviceSelector window will not appear if
you have also connected a USB interface
cable to the machine before restarting your
Macintosh® or if you are overwriting a
previously installed version of the Brother
software. If you encounter this problem
continue with the installation skipping steps 9
to 11. You should then select your Brother
machine from the Model pull-down list in the
main screen of ControlCenter2. (For details,
see the software User’s Guide on the
CD-ROM.)
Insert the supplied CD-ROM for Macintosh®
into your CD-ROM drive.
8
Plug in the power cord and turn on the
machine.
Network
Turn on your Macintosh®.
After the DeviceSelector window appears,
connect the network interface cable to the
machine, and then connect it to a free port
on your hub.
Network
Administrators
2
3
7
Installing the Drivers & Software
Switch off the machine and disconnect the
machine from the power socket and from
the Macintosh®.
Macintosh®
1
Follow the on-screen instructions, and
restart your Macintosh®.
Continued...
27
Step 2
Installing the Drivers & Software
For Network Interface Cable Users (DCP-8065DN only)
9
Choose Network and then click OK.
0
If you want to use the Scan key on the
machine, you must check Register your
computer with the "Scan To" functions
at the machine box and enter a name you
want to use for your Macintosh® in Display
Name. The name you enter will appear on
the machine’s LCD when you press the
Scan key and choose a scan option. You
can enter any name up to 15 characters
long.
(For more information on network scanning,
see Chapter 10 of the Software User’s
Guide on the CD-ROM.)
A
Click Browse.
B
Choose your model name, and then click
OK. Click OK again to close the
DeviceSelector.
C
Click Go, then choose Application.
D
Double-click the Utilities folder.
E
Double-click the Print Setup Utility icon.
For Mac OS® 10.2.x users, double-click the
Print Center icon.
28
Setting Up
the machine
I
For Mac OS® X 10.2.4 to 10.3.x users
➝ Go to G
The MFL-Pro Suite, printer driver,
scanner driver and ControlCenter2
have been installed.
For Mac OS® X 10.4 users ➝ Go to H
Make the selection shown below.
For configuration of advanced network
functions such as LDAP and Scan to FTP,
see the Network User’s Guide located on the
CD-ROM.
J
Choose your model name, and then click
Add.
For Mac OS® X 10.2.4 to 10.3 users:
When Presto! ® PageManager® is installed
OCR capability is added to the Brother
ControlCenter2. You can also easily scan,
share, and organize photos and documents
using Presto!® PageManager®.
For Mac
OS® X
10.4 or greater users:
Presto!® PageManager® has been
installed and the installation is now
complete.
Network
H
To install Presto!® PageManager®, click the
Presto! PageManager icon and follow the
on-screen instructions.
Network
Administrators
G
Click Printer Setup Utility, then choose
Quit Printer Setup Utility.
Installing the Drivers & Software
Click Add.
Macintosh®
F
29
■ For Network Users and Administrators (DCP-8065DN only)
BRAdmin Professional configuration utility
(For Windows® users)
The BRAdmin Professional utility for Windows® is designed to manage your Brother network
connected devices such as network-ready Multifunction devices and or network-ready printers
in a Local Area Network (LAN) environment.
For more information on BRAdmin Professional and BRAdmin Light, go to
http://solutions.brother.com
Installing the BRAdmin Professional configuration utility
30
1
Put the supplied CD-ROM into your CD-ROM drive.
The opening screen will appear automatically.
Follow the on-screen instructions.
2
Click the Install Optional Applications icon on the main menu screen.
3
Click BRAdmin Professional and follow the on-screen instructions.
Windows®
USB
Double-click the new device.
Enter the IP Address, Subnet Mask and
Gateway, and then click the OK button.
5
The address information will be saved to the
machine.
Windows
NT® 4.0
Parallel
4
Windows®
Parallel
The default password for the print server is
‘access’. You can use BRAdmin
Professional or a web browser to change this
password.
Windows®
Network
For more information on network
administration, please see the Network
User’s Guide in the programs menu or go to
http://solutions.brother.com
Macintosh®
USB
Click Devices, then choose Search Active
Devices.
BRAdmin will search for new devices
automatically.
3
Macintosh®
Network
2
Start BRAdmin Professional, and select
TCP/IP.
Network
Administrators
1
Setting Up
the machine
Setting your IP Address, Subnet Mask and Gateway using BRAdmin
Professional
31
BRAdmin Light configuration utility
(For Mac OS® X users)
The Brother BRAdmin Light software is a Java™ application that is designed for the Apple Mac
OS® X environment. It supports some of the features of the Windows BRAdmin Professional
software. For example, using the BRAdmin Light software, you can change some network
settings on Brother’s network ready printers and multifunction devices.
The BRAdmin Light software will be installed automatically when you install the MFL-Pro Suite.
Please refer to Installing the driver and software in this Quick Setup Guide if you have not yet
installed the MFL-Pro Suite.
For more information on BRAdmin Light, visit us at http://solutions.brother.com.
Setting your IP address, Subnet Mask and Gateway using BRAdmin Light
■ If you have a DHCP/BOOTP/RARP server
in your network, you don’t have to do the
following operation. The print server will
automatically obtain its own IP address.
Make sure that version 1.4.1_07 or later of
Java™ client software is installed on your
computer.
■ The default password for the print server is
‘access’. You can use BRAdmin Light to
change this password.
1
2
32
Double-click the Macintosh HD icon on
your desktop.
Choose Library, Printers, Brother and
then Utilities.
3
Double-click the BRAdmin Light.jar file.
Run the BRAdmin Light software. BRAdmin
Light searches new devices automatically.
4
Double-click the new device.
5
Enter the IP Address, Subnet Mask and
Gateway, and then click OK.
6
The address information will be saved to the
printer.
■ Options and Consumables
Setting Up
the machine
Options
The machine has the following optional accessories. You can expand the capabilities of the
machine by adding these items.
Lower Tray Unit
Memory
Second lower paper tray unit expands total input capacity up
to 500 sheets.
Windows®
Parallel
Windows®
USB
LT-5300
You can expand the memory by installing a (144-pin DIMM)
memory module. For more details, see “Memory Board” in
Chapter B of the User’s Guide.
Windows
NT® 4.0
Parallel
Replacement Consumables
TN-3145 / TN-3185
Macintosh®
USB
DR-3115
Macintosh®
Network
Toner Cartridge
Network
Administrators
Drum Unit
Windows®
Network
When the time comes to replace consumables, an error message will be indicated on the LCD.
For more information about the consumables for your machine, visit
http://solutions.brother.com or contact your local Brother re-seller.
33
Trademarks
The Brother logo is a registered trademark of Brother Industries, Ltd.
Brother is a registered trademark of Brother Industries, Ltd.
Multi-Function Link is a registered trademark of Brother International Corporation.
© 2006 Brother Industries, Ltd. All rights reserved.
Windows, Microsoft and Windows NT are registered trademarks of Microsoft in the U.S. and other countries.
Macintosh is a registered trademark of Apple Computer, Inc.
Postscript and Postscript Level 3 are registered trademarks or trademarks of Adobe Systems Incorporated.
PaperPort is a registered trademark of ScanSoft, Inc.
Presto! PageManager is a registered trademark of NewSoft Technology Corporation.
Each company whose software title is mentioned in this manual has a Software License Agreement specific to its
proprietary programs.
All other brand and product names mentioned in this manual are registered trademarks of their respective
companies.
Compilation and Publication
Under the supervision of Brother Industries Ltd., this manual has been compiled and published, covering the latest
product descriptions and specifications.
The contents of this manual and the specifications of this product are subject to change without notice.
Brother reserves the right to make changes without notice in the specifications and materials contained herein and
shall not be responsible for any damages (including consequential) caused by reliance on the materials presented,
including but not limited to typographical and other errors relating to the publication.
This product is designed for use in a Professional Environment.
©2006 Brother Industries, Ltd. ©1998-2006 TROY Group, Inc.
©1983-2006 PACIFIC SOFTWORKS INC.
This product includes the “KASAGO TCP/IP” software developed by Elmic Systems, Inc. ALL RIGHTS
RESERVED.
ARL/ASA/NZ