Setup guide | Brother HL-1660E Printer User Manual

Setting Up the Printer
Color Laser Printer HL-2600CN series
Quick Setup Guide
Step 1 Install the Oil Bottle and the Fuser Cleaner
Read the "Safety Sheet" first to ensure that you use this printer safely.
Read this "Quick Setup Guide" before you set up the printer.
Before you can use the printer, you must set up the hardware and install the driver.
Identify the operating system on your computer (Windows® 95 / 98 / Me,
Windows NT® 4.0, Windows® 2000 / XP or Macintosh®).
The interface cable is not a standard accessory. Please purchase the appropriate
interface cable for the interface you intend to use (Parallel, USB or Network).
Most existing parallel cables support bi-directional communication, but some might
have an incompatible pin assignment or may not be IEEE 1284 compliant.
If you are an Administrator: Configure your network printer settings referring to the
reverse side of this sheet.
Fusing Unit
Pressure Release
Lever
Protective Parts
Top Cover
Oil Bottle Lock Lever
Oil Bottle
Fuser Cleaner
Fusing Unit
1
Remove the protective parts.
Open the top cover.
2
Move the fusing unit pressure
release levers to the SET position.
3
Install the oil bottle in the fusing unit with the
label side facing you.
Step 2 Install the OPC Belt Cartridge
4
Insert the fuser cleaner into the fusing
unit with the roller side facing you.
Lock both oil bottle lock levers.
5
Note: Please be careful not to touch the green surface of the OPC belt or expose it to light for any length of time.
Protective Sheet
Carton Components
Carton components may differ from one country to another.
Save all packing materials and the printer carton. They should be used when shipping the printer.
CD-ROM
(including User's
Guide)
Quick Setup Guide
Windows®
Driver Installation Guide
Macintosh®
Belt Tension
Release Pin
AC power cord
Belt Cartridge
Lock Levers
Driver Installation Guide
1
Oil bottle
Fuser cleaner
OPC belt cartridge
OPC Belt
Cartridge
Printer Guides
Front Cover
Open the front cover.
2
Release both belt cartridge lock
levers.
Remove the orange belt tension release pins from
both sides of the OPC belt cartridge.
Remove the protective sheet.
3
4
Insert the OPC belt cartridge into the
printer guides with the flat side facing
you.
5
Lock the belt cartridge lock levers.
Close the top cover.
Oil syringe
Printer
Step 3 Install the Toner Cartridges
Toner Cartridge
'REMOVE' Tape
Protective Cover
Color Labels
K
Toner cartridges (Black, Cyan, Magenta and Yellow)
1
What is Included on the CD-ROM
You can Find a Variety of Information on this CD-ROM.
Install Software
Install the printer driver and utilities.
(Mac OS X is not supported by Install
Software).
Rock the toner cartridge 3
to 4 times.
2
Pull off the tape labeled 'REMOVE,' and
then remove the orange protective cover.
3
Install the toner cartridge by sliding it into the correct guide.
Match the cartridge color label to the corresponding label
on the printer.
Step 4 Load Paper in the Paper Tray
4
K
Y
Y
M
M
C
C
Repeat Steps 1 through 3 for the
remaining toner cartridges.
5
Close the front cover.
Paper Guide
Paper Guide
Maintenance Tutorial
Instructional movie for printer maintenance.
Windows®
Manual
View the User's Guide and Network User's
Guide in PDF format. (Viewer included)
Color PDF Print Samples
View color samples of printouts from an
HL-2600CN in PDF format.
Paper Tray
Protective Part
1
Remove the protective part.
2
Pull the paper tray completely out of the
printer.
3
Adjust the paper guides to fit the size of paper you want to load.
Load paper in the paper tray.
Step 5 Print a Test Page
Control Panel
Learn More
Watch instructional movies to learn about
our unique software features.
K
Power
Macintosh®
LJ3746001 Printed in Japan
The Brother Solutions Center
(http://solutions.brother.com) is your onestop resource for all your printer needs.
Download the latest drivers and utilities for
your printers, read the FAQs and
troubleshooting tips or learn about special
print solutions.
M
Unfold the Tray
Extention Flap
Y
K
1
Make sure the printer power button is off.
Do NOT connect the interface cable.
2
Connect the AC power cord to the
printer, and then plug it into the AC
outlet.
3
Turn on the
power button.
4
M
Y
NETWORK READY
HL-2600CN
Data
Go
Job
Cancel
Power
Ready
Data
Go
Job
Cancel
Back
Set
Alarm
Secure
Print
Reprint
C
NETWORK READY
HL-2600CN
Ready
Alarm
Brother Solutions Center
C
Re-install the paper tray in the printer.
4
Secure
Print
Back
Set
After the printer warms, the READY message
will appear.
Reprint
5
Press the Go button. The printer will print a test page.
Check that the test page is printed correctly.
Note: When you want to change the language of the control panel masssage, refer to "Setting Your Language on the Control Panel" on the reverse.
Continue to the Windows® Driver Installation Guide or Macintosh® Driver Installation Guide.
Network Quick Setup Guide
For the Administrator
If you are going to connect the printer to your network, we recommend that you contact your system administrator prior to
installation.
If you are an Administrator: Configure your network printer setting referring to the following instructions.
The default password for the print server is 'access'. You can use the BRAdmin Professional Software or a web browser to change
this password.
(For Windows® Users Only)
Install the BRAdmin Professional Configuration utility
The BRAdmin Professional software is designed to manage your Brother network connected devices. For example, Brother network
ready printers and Brother network ready Multifunction devices can be managed using the BRAdmin Professional software. The
BRAdmin Professional software can also be used to manage devices from other manufacturers whose products support the SNMP
(Simple Network Management Protocol).
For more information on the BRAdmin Professional utility go to http://solutions.brother.com
Setting Your Language on the Control Panel
To change the language settings of the printer do the following.
(All references are to what you will see in the lower portion of the LCD panel.)
- - MENU - SETUP
READY
K
C
M
SETUP
LANGUAGE
LANGUAGE
=ENGL I SH
READY
*
1
Y
NETWORK READY
Ready
HL-2600CN
Power
Ready
Data
Go
Job
Cancel
Alarm
Set
Back
Set
Back
Set
Reprint
Back
1
Set
2
Press the Set button
again.
3
Scroll through the available languages by
pressing the + or - buttons. Press the Set
button to accept the appropriate language.
An asterisk mark (*) appears on the LCD.
4
Windows®
To set the printer IP address using the printer control panel do the following.
(All references are to what you will see in the lower portion of the LCD panel.)
K
C
M
I P ADDRESS=
192 .
0.
0 . 192
TCP / I P
I P ADDRESS=
NETWORK
TCP / I P
- - MENU - NETWORK
Windows® 95/98/Me
Peer-to-Peer
Windows NT®
Brother Internet Print
Netware
Peer-to-Peer
Windows® 2000/XP
Brother Internet Print (NT® 4.0 only)
Netware
Peer-to-Peer
*
Y
NETWORK READY
HL-2600CN
Power
Ready
Data
Go
Job
Cancel
Alarm
Back
Set
Back
Set
Back
Back
Set
Set
Secure
Print
Reprint
Back
Set
1
Press the + button until
NETWORK is displayed.
Press the Set button.
2
Press the Set button
again.
3
Press the + button until IP
ADDRESS = is displayed.
Press the Set button.
SUBNET MASK=
0.
0.
0.
TCP / I P
SUBNET MASK=
4
Enter the IP address of the printer using
the + and - buttons. Press the Set button
to go to next digit. Press the Set button
to complete the IP address.
An asterisk mark (*) appears on the LCD.
READY
0
3
Click "BRAdmin Professional."
Follow the instructions on the screen.
Press the Go button to put
the printer back into its
READY state.
Setting Your Printer IP Address and Subnet Mask (Using the Control Panel)
READY
Click the Install Software icon
on the Menu screen.
To configure the print server refer to the Network User's Guide.
Secure
Print
Press the + button until
SETUP is displayed.
Press the Set button.
2
Network User's Guide Chapter Map
Go
Back
Insert the CD-ROM into your CD-ROM drive.
The opening screen will appear automatically.
Follow the instructions on the screen.
(Windows® 2000 only)
IPP (Internet Printing Protocol)
Brother Internet Print
Netware
UNIX/Linux
Macintosh®
OS2 Warp Server
LAN Server
*
Macintosh®
TCP/IP
NetBIOS
TCP/IP
IPX/SPX
TCP/IP
NetBIOS
DLC/LLC
TCP/IP
IPX/SPX
TCP/IP
NetBIOS
DLC/LLC
TCP/IP
TCP/IP
IPX/SPX
TCP/IP
AppleTalk
TCP/IP
TCP/IP
NetBIOS
Chapter 3
Chapter 4
Chapter 5
Chapter 6
Chapter 2
Chapter 4
Chapter 8
Chapter 5
Chapter 6
Chapter 2
Chapter 4
Chapter 8
Chapter 2
Chapter 5
Chapter 6
Chapter 1
Chapter 7
Chapter 7
Chapter 2
Chapter 4
Peer-to-Peer Printing
NetBIOS Peer-to-Peer Printing
How to Configure Internet Printing
Novell Netware Printing
TCP/IP Printing
NetBIOS Peer-to-Peer Printing
DLC Printing
How to Configure Internet Printing
Novell Netware Printing
TCP/IP Printing
NetBIOS Peer-to-Peer Printing
DLC Printing
TCP/IP Printing
How to Configure Internet Printing
Novell Netware Printing
UNIX Printing
Macintosh Printing
Macintosh Printing
TCP/IP Printing
NetBIOS Peer-to-Peer Printing
Ready
Print Configuration Page
Go
Back
5
Set
Back
Press the + button until
SUBNET MASK= is displayed.
Press the Set button.
6
Set
Enter the subnet mask settings in the same
way that you entered the IP address.
An asterisk mark (*) appears on the LCD.
7
Press the Go button to put the printer
back into its READY state.
To print a configuration page, use a fine ball point pen to hold down the
Network Test Button for less than 5 seconds.
Factory Default Setting
For more information refer to the Network User's Guide on the supplied CD-ROM or go to http://solutions.brother.com
©2001 Brother Industries, Ltd. ©1998-2001 TROY XCD Inc. ©1983-1998 PACIFIC SOFTWORKS INC. ALL RIGHTS RESERVED
Windows and Windows NT are registered trademarks of Microsoft Corporation in the U.S. and other countries. HP, HP/UX, JetDirect and JetAdmin are trademarks of Hewllet-Packard Company. UNIX is a trademark of UNIX
Systems Laboratories. PostScript is trademark of Adobe Systems Incorporated. Netware is a trademark of Novell, Inc. Apple Macintosh, iMac, LaserWriter, and AppleTalk are trademarks of Apple Computer, Inc. BRAdmin
Professional is a trademark of Brother Industries, Ltd.
All other brand and product names mentioned in this Network Quick Setup Guide and User's Guide are registered trademarks or trademarks of respective companies.
If you wish to reset the print server back to its default factory settings
(resetting all information such as the password and IP address information),
use a fine ball point pen to hold down the Network Test Button for more than 5
seconds.
Test Button
Download PDF

advertising