Brother HL5070N Printer User Manual

Read this Quick Setup Guide before using the printer.
Before you can use the printer, you must set up the hardware and install
the driver.
Setting Up
Your Printer
Setting Up Your Printer
Windows®
USB
Step 2
Parallel
page 14
Peer-toPeer (LPR)
page 16
Peer-toPeer
(NetBIOS)
page 18
Network
USB
Network
Network
Shared
Printer
page 20
Mac®
Mac®
OS 8.6 – 9.2 OS X 10.1 –
page 22
10.2
page 25
Mac®
Mac®
OS 8.6 – 9.2 OS X 10.1 –
page 27
10.2
page 29
For the latest driver and to find the best solution for your problem or question, access the Brother
Solutions Center directly from the CD-ROM/Driver or go to http://solutions.brother.com
Keep this Quick Setup Guide and supplied CD-ROM in a convenient place for quick and easy
reference at all times.
For
Administrators
Setup is Complete!
Macintosh®
Network
Macintosh®
USB
USB
page 12
Windows®
Network
Windows®
Parallel
Installing the Driver
Installing the Driver
Quick Setup Guide
HL-5070N series
Step 1
Version 0
Safety Precautions
To Use the Printer Safely
User's Guide
Warning
Indicates warnings that
must be observed to
prevent possible
personal injury.
Note
Indicates cautions that
must be observed to use
the printer properly or
prevent damage to the
printer.
Hint
Indicates notes and
useful tips to remember
when using the printer.
Network
User's Guide
Indicates reference to the
User's Guide or Network
User's Guide which is on
the CD-ROM we have
supplied.
Warning
There are high voltage electrodes inside the printer.
Before replacing internal parts, cleaning the printer or
clearing a paper jam, make sure you have turned OFF
the power switch and unplugged the power cord from
the power outlet.
Do not handle the plug with wet hands. Doing this might
cause an electrical shock.
After you have just used the printer, some internal parts
of the printer are extremely hot. When you open the
front cover or rear cover of the printer, never touch the
shaded parts shown in the illustration.
Inside the printer
(Front View)
Open the Face-up Output Tray
(Rear View)
Table of Contents
Regulations ........................................................................................................... 2
■ Getting Started
Carton Components ............................................................................................. 4
Control Panel ........................................................................................................ 5
Supplied CD-ROM ................................................................................................ 6
Step 1
Setting Up Your Printer
■ Insert the CD-ROM into the CD-ROM Drive ....................................................... 7
■ Install the Drum Unit Assembly .......................................................................... 8
■ Load Paper in the Paper Tray ............................................................................. 9
■ Print a Test Page ................................................................................................ 10
Step 2
Installing the Driver
For USB Interface Cable Users ................................................................ 12
1. Installing the Driver and Connecting the Printer to Your PC
2. Setting Your Printer as the Default Printer (For Windows® 2000/XP Users Only)
For Parallel Interface Cable Users .......................................................... 14
Connecting the Printer to Your PC and Installing the Driver
For Network Interface Cable Users ......................................................... 16
■ For Brother Peer-to-Peer Network Printer Users (LPR) ................................. 16
Connecting the Printer to Your Network and Installing the Driver
■ For Brother Peer-to-Peer Network Printer Users (NetBIOS) .......................... 18
Connecting the Printer to Your Network and Installing the Driver
■ For Network Shared Printer Users ................................................................... 20
Installing the Driver, Connecting the Cable and Selecting the Appropriate Printer Queue or 'Share name'
For USB Interface Cable Users ................................................................ 22
■ For Mac® OS 8.6 to 9.2 Users ........................................................................... 22
1. Connecting the Printer to your Macintosh & Installing the Driver
2. Setting your Printer as the Default Printer
■ For Mac® OS X 10.1 to 10.2 Users .................................................................... 25
Connecting the Printer to your Macintosh & Installing the BR-Script PPD File
For Network Interface Cable Users ......................................................... 27
■ For Mac® OS 8.6 to 9.2 Users ........................................................................... 27
Connecting the Printer to your Macintosh & Installing the BR-Script PPD File
■ For Mac® OS X 10.1 to 10.2 Users .................................................................... 29
Connecting the Printer to your Macintosh & Installing the BR-Script PPD File
■ For Administrators
Network User's Guide Chapter Map ................................................................. 31
Installing the BRAdmin Professional Configuration Utility
(Windows® Users Only) ................................................................................... 32
Web BRAdmin (Windows® Users Only) ........................................................... 32
Setting your IP Address, Subnet Mask and Gateway using
BRAdmin Professional (Windows® Users Only) ........................................... 33
Print Printer Settings Page ................................................................................ 33
Factory Default Setting ...................................................................................... 33
■ Other Information
Shipment of the Printer ...................................................................................... 34
Options ................................................................................................................ 35
■ Troubleshooting
User’s Guide Chapter 6
1
Regulations
Federal Communications Commission (FCC) Declaration of
Conformity (For USA)
Responsible Party:
Brother International Corporation
100 Somerset Corporate Boulevard
P.O. Box 6911
Bridgewater, NJ 08807-0911
USA
Telephone: (908) 704-1700
declares, that the products
Product name:
Model number:
Model number:
Product options:
Laser Printer
Laser Printer HL-5030, 5040, 5050 and HL-5070N
HL-50
Lower Tray Unit LT-5000/DIMM
complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
–
–
–
–
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Important
A shielded interface cable should be used in order to ensure compliance with
the limits for a Class B digital device.
Changes or modifications not expressly approved by Brother Industries, Ltd.
could void the user's authority to operate the equipment.
Industry Canada Compliance Statement (For Canada)
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada.
Radio interference (220-240 volt model only)
This printer follows EN55022 (CISPR Publication 22)/Class B.
"EC" Declaration of Conformity
Manufacture
Brother Industries Ltd.,
15-1, Naeshiro-cho, Mizuho-ku,
Nagoya 467-8561, Japan
Plant
Brother Corporation (Asia) Ltd.,
Brother Buji Nan Ling Factory,
Golden Garden Ind., Nan Ling Village,
Buji Rong Gang Shenzhen, China
Herewith declare that:
Products description:
Product Name:
Model Number:
Laser Printer
HL-5030, HL-5040, HL-5050, HL-5070N
HL-50
are in conformity with provisions of the Directives applied: Low Voltage
Directive 73/23/EEC (as amended by 93/68/EEC) and the Electromagnetic
Compatibility Directive 89/336/EEC (as amended by 91/263/EEC and 92/
31/EEC and 93/68/EEC).
Standards applied:
Harmonized:
Safety:
EN60950: 2000
EMC:
EN55022: 1998 Class B
EN55024: 1998
EN61000-3-2: 1995 + A1: 1998 + A2: 1998
EN61000-3-3: 1995
Year in which CE marking was first affixed: 2002
Issued by:
Date:
Place:
Signature:
Brother Industries, Ltd.
2 September, 2002
Nagoya, Japan
Koichi Asai
Manager
Quality Audit Group
Quality Management Dept.
Information & Document Company
International ENERGY STAR® Compliance Statement
The purpose of the International ENERGY STAR® Program is to promote
the development and popularization of energy-efficient office equipments.
As an ENERGY STAR® Partner, Brother Industries, Ltd. has determined
that this product meets the ENERGY STAR® guidelines for energy
efficiency.
Before you use this product, make sure that you use a double-shielded
interface cable with twisted-pair conductors and that it is marked "IEEE1284
compliant". The cable must not be more than 2.0 metres long.
Laser Safety (100 to 120 volt Model Only)
This printer is certified as a Class I laser product under the U.S. Department
of Health and Human Services (DHHS) Radiation Performance Standard
according to the Radiation Control for Health and Safety Act of 1968. This
means that the printer does not produce hazardous laser radiation.
Since radiation emitted inside the printer is completely confined within
protective housings and external covers, the laser beam cannot escape from
the machine during any phase of user operation.
2
FDA Regulations (100 to 120 volt Model Only)
U.S. Food and Drug Administration (FDA) has implemented regulations for
laser products manufactured on and after August 2, 1976. Compliance is
mandatory for products marketed in the United States. One of the following
labels on the back of the printer indicates compliance with the FDA
regulations and must be attached to laser products marketed in the United
States.
MANUFACTURED:
Brother Industries, Ltd.,
15-1 Naeshiro-cho Mizuho-ku Nagoya, 467-8561 Japan
This product complies with FDA radiation performance standards, 21
CFR subchapter J.
MANUFACTURED:
Brother Corporation (Asia) Ltd. Brother Buji Nan Ling Factory
Gold Garden Ind., Nan Ling Village, Buji, Rong Gang, Shenzhen, CHINA
This product complies with FDA radiation performance standards, 21
CFR Subchapter J
☛ Caution:
Use of controls, adjustments or performance of
procedures other than those specified in this manual may
result in hazardous radiation exposure.
Disconnect device
You must install this printer near a power outlet that is easily accessible. In
case of an emergency, you must disconnect the power cord from the power
outlet to shut off the power completely.
Caution for batteries
Do not replace the battery. There is a danger of explosion if the battery is
incorrectly replaced. Do not disassemble, recharge or dispose of the battery
in fire. Dispose of used batteries according to local regulations.
Caution for LAN connection
Connect this product to a LAN connection that is not subjected to over
voltages.
IT power system (For Norway only)
This product is also designed for an IT power system with phase-to-phase
voltage 230V.
Opmerking / Oplaadbare Batterij Recycle Informatie (For
Netherlands Only)
Bij dit product zijn batterijen geleverd. Wanneer deze
leeg zijn, moet u ze niet weggooien maar inleveren als
Klein Chemisch Afval.
IEC 60825 specification (220 to 240 volt model only)
This printer is a Class 1 laser product as defined in IEC 60825 specifications.
The label shown below is attached in countries where it is needed.
CLASS 1LASERP RODUCT
APPAREIL Å LASER DE CLASSE 1
LASER KLASSE 1 PRODUKT
Geräuschemission / Acoustic noise emission (for Germany
only)
Lpa < 70 dB (A) DIN 45635-19-01-KL2
Wiring information (for UK)
This printer has a Class 3B laser diode which produces invisible laser
radiation in the scanner unit. You should not open the scanner unit under any
circumstances.
☛ Caution:
Use of controls or adjustments or performance of
procedures other than those specified herein may result in
hazardous radiation exposure.
For Finland and Sweden
LUOKAN 1 LASERLAITE
KLASS 1 LASER APPARAT
☛ Varoitus!
Laitteen käyttäminen muulla kuin tässä käyttöohjeessa
mainitulla tavalla saattaa altistaa käyttäjän
turvallisuusluokan 1 ylittävälle näkymättömälle
lasersäteilylle.
☛ Varning
Om apparaten används på annat sätt än i denna
Bruksanvisning specificerats, kan användaren utsättas för
osynlig laserstrålning, som överskrider gränsen för
laserklass 1.
Internal laser radiation
Maximum radiation power: 5 mW
Wave length:
760 - 810 nm
Laser class:
Class IIIb
(Accordance with 21 CFR Part 1040.10)
Class 3B
(Accordance with IEC 60825)
IMPORTANT - For Your Safety
To ensure safe operation the supplied three-pin plug must be inserted only
into a standard three-pin power outlet that is properly grounded through the
normal household wiring.
Important
If the mains plug that is supplied with this printer is not suitable for your plug
socket, remove the plug from the mains lead and fit an appropriate three-pin
plug. If the replacement plug needs a fuse, fit the same fuse as the original.
If a moulded plug comes off the mains lead, you should destroy it because a
plug with cut wires is dangerous if it is put in a live plug socket. Do not leave
it where a child might find it!
If you need to replace the plug fuse, fit a fuse that is approved by ASTA to
BS1362 with the same rating as the original fuse.
Always replace the fuse cover. Never use a plug that does not have a cover.
Warning - This printer must be earthed.
The wires in the mains lead are coloured in line with the following code :
Green and Yellow:
Blue:
Brown:
Earth
Neutral
Live
The colours of the wires in the mains lead of this printer may not match the
coloured markings identifying the terminals in your plug.
If you need to fit a different plug, you should do the following.
Remove a bit of the outer cover of the lead, taking care not to damage the
coloured insulation of the wires inside.
Cut each of the three wires to the appropriate length. If you can, leave the
green and yellow wire longer than the others so that, if the lead is pulled out
of the plug, the green and yellow wire will be the last to disconnect.
Remove a short section of the coloured insulation to expose the wires.
Extension cords used with this printer must be three-pin plug type and
correctly wired to provide proper grounding. Incorrectly wired extension
cords may cause personal injury and equipment damage.
The wire which is coloured green and yellow must be connected to the
terminal in the plug which is marked with the letter "E" or the safety earth
symbol
, or coloured green or green and yellow.
The fact that the equipment operates satisfactorily does not imply that the
power is grounded and that the installation is completely safe. For your
safety, if in any doubt about the effective grounding of the power, call a
qualified electrician.
The wire, which is coloured blue, must be connected to the terminal, which is
marked with the letter "N" or coloured black or blue.
The wire, which is coloured brown, must be connected to the terminal, which
is marked with the letter "L" or coloured red or brown.
The outer cover of the lead must be secured inside the plug. The coloured
wires should not hang out of the plug.
3
■ Getting Started
Carton Components
Printer
1
7
2
1 Face-down Output Tray Support Flap (Support Flap)
2 Control Panel
3 Front Cover Release Button
4 Multi-purpose Tray (MP Tray)
5 Paper Tray
6 Front Cover
7 Face-down Output Tray (Top Output Tray)
3
4
5
6
CD-ROM
(including User's Guide)
Quick Setup Guide
Drum Unit Assembly
AC Power Cord
(including Toner Cartridge)
Carton components may differ from one country to another.
Save all packing materials and the printer carton.
■ The interface cable is not a standard accessory. Please purchase the appropriate interface cable for
the interface you intend to use (Parallel, USB or Network).
■ It’s recommended to use a Parallel interface cable or USB interface cable that is not longer than 6 feet
(2.0 meters).
■ For Parallel interface cable use a shielded interface cable that is IEEE 1284-compliant.
■ Please make sure that you use a Hi-Speed USB 2.0 certified cable if your computer uses a Hi-Speed
USB 2.0 interface.
4
Control Panel
1 Toner
LED indicates when the Toner is low or empty.
2
2 Drum
LED indicates when the Drum is nearing end
of life.
3
3 Paper
LED indicates when there is a paper jam.
4 Status
The LED will flash and change color
depending on the printer status.
1
4
5 Job Cancel Button
Will stop and cancel the print operation in progress.
6 Go Button
5
Pause / Continue printing.
6
Printer LED Indications
: Blinking
Printer LED Sleep / OFF
: ON
: OFF
Warming
Up
Ready
Receiving
Data
Data
Remaining
Green
Green
Yellow
Yellow
Toner
Drum
Paper
Status
Printer
LED
Toner
Toner
Low
Toner
Empty
Yellow *1
Yellow
Drum
Drum End
User's
Guide
Cover
Open
Service
Error
Yellow
Yellow*1
Paper
Status
No Paper/
Paper
Jam
Yellow
Yellow*2
Yellow
Green
Red
Green
Red
Red
Red
Chapter 5
Chapter 5
Chapter 5
Chapter 6
Chapter 6
Chapter 6
*1 The LED will blink in a pattern of ON for 2 seconds and then OFF for 3 seconds.
*2 The LED will blink fast.
5
Supplied CD-ROM
You can find a variety of information on the CD-ROM.
Mac® OS
8.6 to 9.2
Users
3
1
Mac® OS X
10.1 to 10.2
Users
4
5
3
2
4
6
7
5
1
2
6
7
1 Initial Setup
Instructional movie for printer setup and driver installation.
2 Install Software
Installs the printer driver and utilities.
3 Documentation
View the Printer User's Guide and Network User's Guide in PDF format.
(Viewer included)
4 Learn More
Watch instructional movies to learn more about using your Brother printer.
5 Brother Solutions Center
The Brother Solutions Center (http://solutions.brother.com) is a one-stop resource for all
your printer needs. Download the latest drivers and utilities for your printers, read the
FAQs and troubleshooting tips, or learn about printer solutions.
6 Maintenance Tutorial
Instructional movie for printer maintenance.
7 On-Line Registration
Register your product on-line.
For visually impaired users, we have prepared
two HTML files on the supplied CD-ROM:
index_win.html and index_mac.html. These files
can be read by Screen Reader 'text-to-speech'
software.
6
Step 1
Setting Up Your Printer
Setting Up
Your Printer
1 Insert the CD-ROM into the CD-ROM Drive
For Macintosh® Users
For Windows® Users
Do NOT connect the interface cable.
Connecting the interface cable is
done when installing the driver.
Windows®
USB
Do NOT connect the interface cable.
Connecting the interface cable is
done when installing the driver.
Mac® OS
8.6 to 9.2
Users
2
Click the Initial Setup icon on the menu
screen.
3
You can view the Initial Setup instructions
and follow the steps on pages 8 to 11.
You can view the Initial Setup instructions
and follow the steps on pages 8 to 11.
Macintosh®
Network
3
Click the Initial Setup icon on the menu
screen.
For
Administrators
2
Mac® OS X
10.1 to 10.2
Users
Windows®
Parallel
Insert the CD-ROM into your CD-ROM
drive. Double-click the Start Here icon or
Start Here OS X icon.
Follow the on-screen instructions.
Windows®
Network
1
Macintosh®
USB
Insert the CD-ROM into your CD-ROM
drive. The opening screen will appear
automatically.
Follow the on-screen instructions.
Installing the Driver
1
7
Step 1
Setting Up Your Printer
2 Install the Drum Unit Assembly
Do NOT connect the interface cable.
Connecting the interface cable is
done when installing the driver.
1
3
Rock it from side to side several times to
distribute the toner evenly inside the
assembly.
4
Put the drum unit assembly into the printer.
5
Close the front cover of the printer.
Open the front cover by pressing the front
cover release button.
Front cover
release button
Front cover
2
Unpack the drum unit assembly.
Remove the protective part.
Drum unit
assembly
Protective part
8
Fan the stack of paper well to avoid paper
jams and misfeeds.
4
Put paper in the paper tray.
Check that the paper is flat in the tray and
below the maximum paper mark.
Windows®
USB
3
Windows®
Parallel
While pressing the paper guide release lever,
slide the adjusters to fit the paper size.
Check that the guides are firmly in the slots.
Paper guide
release lever
Put the paper tray firmly back in the printer.
Macintosh®
USB
5
Windows®
Network
Up to here.
For Legal size paper, press the
universal guide release button and pull
out the rear of the paper tray.
Macintosh®
Network
Universal guide
release button
For
Administrators
2
Pull the paper tray completely out of the
printer.
Installing the Driver
1
Setting Up
Your Printer
3 Load Paper in the Paper Tray
Go to the next page
9
Step 1
Setting Up Your Printer
4 Print a Test Page
Do NOT connect the interface cable.
Connecting the interface cable is
done when installing the driver.
3
After the printer has finished warming up,
the Status LED stops blinking and stays
green.
Extend the
Support flap.
1
Make sure that the printer power switch is
off.
Connect the AC power cord to the printer.
4
2
Press the Go button. The printer prints a
test page.
Check that the test page has printed
correctly.
Plug the AC power cord into an AC outlet.
Turn the power switch on.
Go to the next page
to install the driver.
10
Step 2
Installing the Driver
Setting Up
Your Printer
Follow the instructions on this page for your operating system and interface cable.
The screens for Windows® in this Quick Setup Guide are based on Windows® XP.
The screens for Mac® OS X in this Quick Setup Guide are based on Mac® OS X 10.1.
Windows®
USB
For USB Interface Cable Users............................Go to page 12
Windows®
Parallel
For Parallel Interface Cable Users.......................Go to page 14
Windows®
Network
For Network Interface Cable Users
■ Brother Peer-to-Peer Network Printer Users (LPR) ......... Go to page 16
■ Brother Peer-to-Peer Network Printer Users (NetBIOS) ....... Go to page 18
■ Network Shared Printer Users........................................... Go to page 20
Go to page 22
Go to page 25
Macintosh®
Network
■ Mac® OS 8.6 to 9.2 Users ..............................................
■ Mac® OS X 10.1 to 10.2 Users ........................................
Macintosh®
USB
For USB Interface Cable Users
For Network Interface Users
Go to page 27
Go to page 29
For
Administrators
■ Mac® OS 8.6 to 9.2 Users ..............................................
■ Mac® OS X 10.1 to 10.2 Users ........................................
For Administrators ...............................................Go to page 31
11
Step 2
Installing the Driver
For USB Interface Cable Users
1. Installing the Driver and Connecting the Printer to Your PC
If the Found New Hardware Wizard
appears on your PC, click the Cancel
button.
1
2
12
L
E
C
N
CA
3
Select the USB interface.
4
Click the Install button.
5
Click the Next button.
Follow the on-screen instructions.
Make sure the USB interface cable is NOT
connected to the printer, and then begin
installing the driver. If you have already
connected the cable, remove it.
Click Connect the interface cable &
Install the driver/utility from the Initial
Setup menu.
Setting Up
Your Printer
When this screen appears, make sure the
printer power switch is on.
Connect the USB interface cable to your
PC, and then connect it to the printer.
Click the Next button.
2. Setting Your Printer as the
Default Printer
(For Windows® 2000/XP Users
Only)
1
Click Start and then Printers and Faxes.
2
Select the Brother HL-5070N series icon.
3
From the File menu, select Set as Default
printer.
Click the Finish button.
The setup is now complete.
For Windows® 98 / Me users:
The Setup is now complete.
For Windows® 2000/XP users:
Go to "2. Setting Your Printer as the
Default Printer".
For
Administrators
7
Installing the Driver
Windows®
USB
6
13
Step 2
Installing the Driver
For Parallel Interface Cable Users
Connecting the Printer to Your PC and Installing the Driver
1
Click Connect the interface cable &
Install the driver/utility from the Initial
Setup menu.
2
Select the Parallel interface.
3
Turn off the printer power switch.
4
Connect the parallel interface cable to your
PC, and then connect it to your printer.
5
Turn on the printer power switch.
If the Found New Hardware Wizard
appears on your PC, click the Cancel
button.
L
E
C
N
CA
14
8
Click the Next button.
Follow the on-screen instructions.
7
Click the Install button.
9
Click the Finish button.
Setting Up
Your Printer
Click the Next button when the movie
finishes.
For
Administrators
The Setup is now complete.
Installing the Driver
Windows®
Parallel
6
15
Step 2
Installing the Driver
For Network Interface Cable Users
For Brother Peer-to-Peer Network Printer Users
(LPR)
If you are going to connect the printer to your network, we recommended that you contact your system
administrator prior to installation.
Connecting the Printer to Your Network and Installing the Driver
16
1
Click Connect the interface cable &
Install the driver/utility from the Initial
Setup menu.
4
Connect the network interface cable to the
printer, and then connect it to a free port on
your hub.
2
Select the Network interface.
5
Turn on the printer power switch.
3
Turn off the printer power switch.
6
Click the Next button when the movie
finishes.
Select the IP address of your printer and
LPR, and then click the Next button.
8
Click the Next button.
Follow the on-screen instructions.
B
Click the Finish button.
Select Brother Peer-to-Peer Network
Printer, and then click the Next button.
For Windows NT® 4.0 and
Windows® 2000/XP users:
The Setup is now complete.
For Windows® 95 / 98 / Me users:
After your PC has restarted, setup will
be complete.
0
Select Search from a list of available
printers or enter your printer’s IP address.
Click the Next button.
For
Administrators
9
Setting Up
Your Printer
A
Windows®
Network
Click the Install button.
Installing the Driver
7
Contact your Administrator about the
Printer's IP Address.
17
Step 2
Installing the Driver
For Network Interface Cable Users
For Brother Peer-to-Peer Network Printer Users
(NetBIOS)
If you are going to connect the printer to your network, we recommended that you contact your system
administrator prior to installation.
Connecting the Printer to Your Network and Installing the Driver
18
1
Click Connect the interface cable &
Install the driver/utility from the Initial
Setup menu.
4
Connect the network interface cable to the
printer, and then connect it to a free port on
your hub.
2
Select the Network interface.
5
Turn on the printer power switch.
3
Turn off the printer power switch.
6
Click the Next button when the movie
finishes.
Select the IP address of your printer and
NetBIOS, and then click the Next button.
8
Click the Next button.
Follow the on-screen instructions.
B
Click the Finish button.
9
Select Brother Peer-to-Peer Network
Printer, and then click the Next button.
For Windows NT® 4.0 and
Windows® 2000/XP users:
The Setup is now complete.
Setting Up
Your Printer
A
Windows®
Network
Click the Install button.
Installing the Driver
7
For Windows® 95 / 98 / Me users:
After your PC has restarted, setup will
be complete.
Select Search from a list of available
printers or enter your printer’s IP address.
Click the Next button.
For
Administrators
0
Contact your Administrator about the
printer's IP Address.
19
Step 2
Installing the Driver
For Network Interface Cable Users
For Network Shared Printer Users
If you are going to connect the printer to your network, we recommended that you contact your system
administrator prior to installation.
Installing the Driver, Connecting the Cable and Selecting the Appropriate
Printer Queue or 'Share name'
20
1
Click Connect the interface cable &
Install the driver/utility from the Initial
Setup menu.
4
Connect the network interface cable to the
printer, and then connect it to a free port on
your hub.
2
Select the Network interface.
5
Turn on the printer power switch.
3
Turn off the printer power switch.
6
Click the Next button when the movie
finishes.
Click the Install button.
8
Click the Next button.
Follow the on-screen instructions.
0
Setting Up
Your Printer
7
Select your printer's queue, and then click
the OK button.
Contact your Administrator about the
Printer's queue.
Windows®
Network
Select Network Shared Printer, and then
click the Next button.
The setup is now complete.
For
Administrators
9
Click the Finish button.
Installing the Driver
A
21
Step 2
Installing the Driver
For USB Interface Cable Users
For Mac® OS 8.6 to 9.2 Users
1. Connecting the Printer to your Macintosh & Installing the Driver
1
Make sure the printer power switch is on.
4
Click the Install button, and follow the
on-screen instructions.
2
Connect the USB interface cable to your
Macintosh, and then connect it to the
printer.
5
Open the Macintosh HD icon.
6
For Mac® OS 8.6 to 9.04 Users:
Open the Apple Extras folder.
Open the Apple LaserWriter Software
folder.
Do not connect the USB cable to the
keyboard USB Port or a non-powered
USB Hub.
3
Click Connect the interface cable &
Install the driver/utility from the Initial
Setup menu.
For Mac® OS 9.1 to 9.2 Users:
Open the Applications (Mac® OS 9) folder.
Open the Utilities folder.
If this screen appears, select the USB
interface.
* The screens are based on Mac® OS 9.04.
22
Select Printer (USB), and then click the OK
button.
A
Click the Create... button.
B
Enter your printer name (HL-5070N series),
and then click the Save button.
C
Select Quit from the File menu.
Click the Change... button in the
PostScriptTM Printer Description (PPD) file.
Select Brother HL-5070N series, and then
click the Select button.
Installing the Driver
9
Click the Change... button in the USB
Printer Selection.
Select HL-5070N series, and then click the
OK button.
Setting Up
Your Printer
8
0
Macintosh®
USB
Open the Desktop Printer Utility icon.
For
Administrators
7
Continue to
the next page
23
Step 2
Installing the Driver
For USB Interface Cable Users
For Mac® OS 8.6 to 9.2 Users
2. Setting your Printer as the Default Printer
1
Click the HL-5070N series icon on the
Desktop.
2
Select Set Default Printer from the
Printing menu.
The setup is now complete.
24
Setting Up
Your Printer
For USB Interface Cable Users
For Mac® OS X 10.1 to 10.2 Users
Connecting the Printer to your Macintosh & Installing the BR-Script PPD File
1
Click Connect the interface cable &
Install the driver/utility from the Initial
Setup menu.
3
Connect the USB interface cable to your
Macintosh, and then connect it to the
printer.
Do not connect the USB cable to the
keyboard USB Port or a non-powered
USB Hub.
Click the Install button, and follow the onscreen instructions.
5
Select Applications from the Go menu.
Macintosh®
USB
Make sure the printer power switch is on.
For
Administrators
2
4
Installing the Driver
If this screen appears, select the USB
interface.
25
Step 2
Installing the Driver
For USB Interface Cable Users
6
Open the Utilities folder.
7
Open the Print Center icon.
8
0
Select HL-5070N series, and then click the
Add button.
A
Select Quit Printer Center from the Printer
Center menu.
Click the Add Printer... button.
The setup is now complete.
9
26
Select USB.
Step
Setting Up
Your Printer
For Network Interface Cable Users
For Mac® OS 8.6 to 9.2 Users
Connect the network interface cable to the
printer, and then connect it to a free port on
your hub.
2
Select the Network interface.
5
Turn on the printer power switch.
3
Turn off the printer power switch.
6
Click the Next button when the movie
finishes.
Macintosh®
USB
4
Macintosh®
Network
Click Connect the interface cable &
Install the driver/utility from the Initial
Setup menu.
For
Administrators
1
Installing the Driver
Connecting the Printer to your Macintosh & Installing the BR-Script PPD File
27
Step 2
Installing the Driver
For Network Interface Cable Users
7
Click the Install button, and follow the on
screen instructions.
8
Open the Chooser from the Apple menu.
9
Click the LaserWriter 8 *1 icon, and then
select BRN_xxxxxx_P1_AT. *2
Click the Create button.
Close the Chooser.
*1 If the Apple LaserWriter 8 Driver is not
already installed on your system, you
can download it from
http://www.apple.com
*2 xxxxxx are the last six digits of the
Ethernet address.
Network User's Guide Chapter 7.
The setup is now complete.
28
2S
Setting Up
Your Printer
For Network Interface Cable Users
For Mac® OS X 10.1 to 10.2 Users
2
Select the Network interface.
3
Turn off the printer power switch.
4
5
Turn on the printer power switch.
6
Click the Install button and follow the on
screen instructions.
7
Select Applications from the Go menu.
8
Open the Utilities folder.
Macintosh®
Network
Click Connect the interface cable &
Install the driver/utility from the Initial
Setup menu.
Connect the network interface cable to the
printer, and then connect it to a free port on
your hub.
For
Administrators
1
Installing the Driver
Connecting the Printer to your Macintosh & Installing the BR-Script PPD File
29
Step 2
Installing the Driver
For Network Interface Cable Users
9
Open the Print Center icon.
0
Click the Add Printer... button.
B
Select BRN_xxxxxx_P1_AT*1, and then
click the Add button.
*1 xxxxxx are the last six digits of the
Ethernet address.
Network User's Guide Chapter 7.
C
A
Select Quit Printer Center from the Printer
Center menu.
Select AppleTalk.
The setup is now complete.
30
■ For Administrators
This section is for using the printer on a network. An administrator should set up the printer
using the following steps.
Network User's Guide Chapter Map
Windows® 95/98/ME Peer-to-Peer
TCP/IP
NetBIOS
TCP/IP
IPX/SPX
TCP/IP
NetBIOS
DLC/LLC
TCP/IP
Chapter 3
Chapter 4
Chapter 5
Chapter 6
Chapter 2
Chapter 4
Chapter 8
Chapter 5
Peer-to-Peer Printing
NetBIOS Peer-to-Peer Printing
How to Configure Internet Print
Novell Netware Printing
TCP/IP Printing
NetBIOS Peer-to-Peer Printing
DLC Printing
How to Configure Internet Print
IPX/SPX
TCP/IP
NetBIOS
(Windows® 2000 only) DLC/LLC
IPP
TCP/IP
(Internet Printing Protocol)
Brother Internet Print
TCP/IP
Chapter 6
Chapter 2
Chapter 4
Chapter 8
Chapter 2
Novell Netware Printing
TCP/IP Printing
NetBIOS Peer-to-Peer Printing
DLC Printing
TCP/IP Printing
Chapter 5
How to Configure Internet Print
Netware
Chapter 6
Chapter 1
Chapter 7
Chapter 7
Chapter 2
Chapter 4
Novell Netware Printing
UNIX Printing
Macintosh Printing
Macintosh Printing
TCP/IP Printing
NetBIOS Peer-to-Peer Printing
Windows NT®
Brother Internet Print
Netware
Peer-to-Peer
Windows® 2000/XP
Brother Internet Print
(NT® 4.0 only)
Netware
Peer-to-Peer
UNIX/Linux
Macintosh®
OS2 Warp Server
LAN Server
IPX/SPX
TCP/IP
AppleTalk
TCP/IP
TCP/IP
NetBIOS
31
Installing the BRAdmin Professional
Configuration Utility (Windows® Users Only)
The BRAdmin Professional software utility is designed to manage your Brother network
connected devices such as network-ready printers and/or network-ready Multifunction devices
in a Local Area Network (LAN) environment.
BRAdmin Professional can also be used to manage devices from other manufacturers whose
products support SNMP (Simple Network Management Protocol).
For more information on BRAdmin Professional go to http://solutions.brother.com
1
Insert the CD-ROM into your CD-ROM
drive. The opening screen will appear
automatically.
Follow the on-screen instructions.
2
Click the Install Software icon on the menu
screen.
3
Follow the instructions on the screen.
Click BRAdmin Professional.
The default password for the print
server is 'access'. You can use the
BRAdmin Professional software or a
web browser to change this password.
Web BRAdmin (Windows® Users Only)
Brother has also developed Web BRAdmin, an enterprise network software utility that enables
management of Brother and other SNMP compliant devices in larger LAN/WAN environments.
This software is Web server based and requires the installation of Microsoft's Internet
Information Server and Sun's Java client software. To learn more about the Web BRAdmin
software or to download it, please go to http://solutions.brother.com/webbradmin
32
Start BRAdmin Professional, and select
TCP/IP.
3
Double-click the new device.
4
Enter the IP Address, Subnet Mask and
Gateway, and then click the OK button.
5
The address information will be saved to the
printer.
Windows®
USB
1
Setting Up
Your Printer
Setting your IP Address, Subnet Mask and
Gateway using BRAdmin Professional
(Windows® Users Only)
Windows®
Network
Macintosh®
USB
You can reset all the print server settings
(including the password) back to factory
defaults. For steps on how to reset the print
server, see Chapter 3 “Network factory
default setting” on page 3-11 of the User's
Guide.
Macintosh®
Network
The Printer Settings Page lists all the current
printer settings, including network settings.
To print the Printer Settings Page, press the
Go button three times.
Factory Default
Setting
User’s Guide Chapter 3
For
Administrators
Print Printer Settings
Page
Windows®
Parallel
Select Search Active Devices from the
Devices menu.
BRAdmin will search for new devices
automatically.
Installing the Driver
2
33
■ Other Information
Shipment of the Printer
If for any reason you must ship your Printer, carefully package the Printer in the original packing
to avoid any damage during transit. It is strongly recommended that you save and use the
original packaging. The Printer should also be adequately insured with the carrier.
When shipping the Printer, the DRUM UNIT assembly and TONER CARTRIDGE must be
removed from the Printer and placed in the foil bag. Failure to remove the unit and place
it in the foil bag during shipping will cause severe damage to the Printer and may VOID
THE WARRANTY.
1
Turn off the printer power switch, and then
unplug the AC power cord.
2
Remove the drum unit assembly.
Place it in the plastic bag and seal the bag
completely.
3
Re-pack the printer.
Trademarks
The Brother logo is a registered trademark of Brother Industries, Ltd.
Windows® and Windows NT® are registered trademarks of Microsoft Corporation in the U.S and other countries.
Apple Macintosh, iMac, LaserWriter, and AppleTalk are trademarks of Apple Computer, Inc.
HP, HP/UX, JetDirect and JetAdmin are trademarks of Hewlett-Packard Company.
UNIX is a trademark of UNIX Systems Laboratories.
Adobe PostScript® and PostScript3TM are trademarks of Adobe Systems Incorporated.
Netware is a trademark of Novell, Inc.
ENERGY STAR is a U.S. registered mark.
All other brand and product names mentioned in this User's Guide are registered
Compilation and Publication
Under the supervision of Brother Industries Ltd., this manual has been compiled and published, covering the latest product
descriptions and specifications.
The contents of this manual and the specifications of this product are subject to change without notice.
Brother reserves the right to make changes without notice in the specifications and materials contained herein and shall not be
responsible for any damages (including consequential) caused by reliance on the materials presented, including but not limited
to typographical and other errors relating to the publication.
This product is designed for use in a Professional Environment.
34
Setting Up
Your Printer
Options
The printer has the following optional accessories. You can expand the capabilities of the
printer by adding these items.
User's Guide Chapter 4.
DIMM Memory
Windows®
Parallel
Windows®
USB
LT-5000
For
Administrators
Macintosh®
Network
Macintosh®
USB
Installing the Driver
Second lower paper tray unit expands total You can expand the memory by installing
input capacity up to 250 sheets.
(100-pin DIMM) memory module.
Windows®
Network
Lower Tray Unit
35
©2003 Brother Industries, Ltd. ©1998-2003 TROY Group, Inc. ©1983-1998 PACIFIC SOFTWORKS INC. ALL
RIGHTS RESERVED