Brother HL-5250DN Printer User Manual

Brother Laser Printer
USER’S GUIDE
HL-5240
HL-5250DN
For visually-impaired users
You can read this manual with Screen
Reader ‘text-to-speech’ software.
You must set up the hardware and install the driver before you can use the printer.
Please use the Quick Setup Guide to set up the printer. You can find a printed copy in the box.
Please read this User’s Guide thoroughly before you use the printer. Keep the CD-ROM in a convenient place so you
can use it quickly if you need to. You can also read the User’s Guide in HTML format by visiting our web site at
http://solutions.brother.com or accessing it from the CD-ROM directly.
Please visit us at http://solutions.brother.com where you can get product support, the latest driver updates and
utilities, and answers to frequently asked questions (FAQs) and technical questions.
Version 0
EN-US_AS
Using this guide
Symbols used in this guide
We use the following icons throughout this User’s Guide:
Warnings tell you what to do to prevent possible personal injury.
Electrical Hazard icons alert you to a possible electrical shock.
Hot Surface icons warn you not to touch machine parts that are hot.
Cautions specify procedures you must follow or avoid to prevent possible damage to the
printer or other objects.
Improper Setup icons alert you to devices and operations that are not compatible with the
printer.
Notes tell you how you should respond to a situation that may arise or give tips about how
the operation works with other features.
i
Safety precautions
To use the printer safely
WARNING
There are high voltage electrodes inside the printer. Before you clean the inside of the printer, make sure
that you have turned off the power switch and unplugged the printer from the AC power outlet.
DO NOT handle the plug with wet hands. Doing this might cause an electrical shock.
After you have just used the printer, some internal parts of the printer will be extremely hot. When you open
the front or back cover of the printer, DO NOT touch the shaded parts shown in the illustration.
Inside the printer
Open the back cover
(Front View)
(Back View)
ii
DO NOT remove or damage the caution labels located on or around the fuser.
DO NOT use a vacuum cleaner to clean up scattered toner. Doing this might cause the toner dust to ignite
inside the vacuum cleaner, potentially starting a fire. Carefully clean the toner dust with a dry, lint-free cloth
and dispose of it according to local regulations.
DO NOT use flammable substances near the printer. Doing this might cause a fire or electrical shock.
CAUTION
Cleaning the outside of the printer:
• Make sure that you have unplugged the printer from the AC power outlet.
• Use neutral detergents. Cleaning with volatile liquids such as thinner or benzine will damage the outside
surface of the printer.
• DO NOT use cleaning materials that contain ammonia.
iii
Trademarks
The Brother logo is a registered trademark of Brother Industries, Ltd.
Apple, the Apple Logo, Macintosh and TrueType are registered trademarks of Apple Computer, Inc in the
United States and other countries.
Epson is a registered trademark and FX-80 and FX-850 are trademarks of Seiko Epson Corporation.
Hewlett Packard is a registered trademark and HP LaserJet 6P, 6L, 5P, 5L, 4, 4L 4P, III, IIIP, II, and IIP are
trademarks of Hewlett-Packard Company.
IBM, IBM PC, and Proprinter are registered trademarks of International Business Machines Corporation.
Microsoft, MS-DOS, Windows and Windows NT are registered trademarks of Microsoft Corporation in the
U.S. and other countries.
PostScript and PostScript 3 are trademarks of Adobe Systems Incorporated.
ENERGY STAR is a U.S. registered mark.
Citrix and MetaFrame are registered trademarks of Citrix Systems, Inc. in the United States.
SuSE is a registered trade mark of SuSE Linux AG.
RED HAT is a registered trade mark of Red Hat. Inc.
Mandrake is a registered trade mark of Mandrake Soft SA.
Intel, Intel Xeon and Pentium are trademarks or registered trademarks of Intel Corporation.
AMD, AMD Athlon, AMD Opteron and combinations thereof, are trademarks of Advanced Micro Devices, Inc.
Java and all Java-based trademarks and logos are trademarks or registered trademarks of
Sun Microsystems, Inc. in the United States and other countries.
All other terms and brand and product names mentioned in this User’s Guide are registered trademarks of
their respective companies.
Compilation and Publication Notice
Under the supervision of Brother Industries Ltd., this manual has been compiled and published, covering the
latest product’s descriptions and specifications.
The contents of this manual and the specifications of this product are subject to change without notice.
Brother reserves the right to make changes without notice in the specifications and materials contained
herein and shall not be responsible for any damages (including consequential) caused by reliance on the
materials presented, including but not limited to typographical and other errors relating to the publication.
© 2005 Brother Industries Ltd.
Shipment of the Printer
If for any reason you must ship your printer, carefully package the printer to avoid any damage during transit.
We recommend that you save and use the original packaging. The printer should also be adequately insured
with the carrier.
iv
Table of Contents
1
About this Printer
What is in the box? ................................................................................................................................ 1-1
Interface cable ................................................................................................................................. 1-1
Front view ........................................................................................................................................ 1-2
Back view ........................................................................................................................................ 1-3
Positioning the printer ............................................................................................................................ 1-4
Power supply ................................................................................................................................... 1-4
Environment .................................................................................................................................... 1-4
2
Printing Methods
About paper ........................................................................................................................................... 2-1
Type and size of paper .................................................................................................................... 2-1
Recommended paper ...................................................................................................................... 2-2
Printable area .................................................................................................................................. 2-4
Printing methods.................................................................................................................................... 2-5
Printing on plain paper, bond paper and transparencies................................................................. 2-5
Printing on thick paper, labels and envelopes ............................................................................... 2-11
Duplex Printing .................................................................................................................................... 2-15
Guidelines for printing on both sides of the paper ......................................................................... 2-15
Manual duplex printing .................................................................................................................. 2-15
Automatic duplex printing (For HL-5250DN) ................................................................................. 2-18
Booklet printing (For Windows printer driver) ................................................................................ 2-19
3
Driver and Software
Printer driver .......................................................................................................................................... 3-1
Features in the printer driver (For Windows®) ................................................................................. 3-4
Features in the BR-Script (PostScript® 3™ language emulation) printer driver
(For Windows®) ......................................................................................................................... 3-12
Features in the printer driver (For Macintosh®) ............................................................................. 3-15
Uninstalling the printer driver......................................................................................................... 3-18
Software .............................................................................................................................................. 3-20
Software for networks (For HL-5250DN only) ............................................................................... 3-20
About emulation modes................................................................................................................. 3-21
Automatic emulation selection....................................................................................................... 3-21
Automatic interface selection......................................................................................................... 3-22
Remote Printer Console ................................................................................................................ 3-22
4
Control Panel
LEDs (Light Emitting Diodes)................................................................................................................. 4-1
Service call indications .......................................................................................................................... 4-5
Control panel button .............................................................................................................................. 4-7
Print a test page .............................................................................................................................. 4-8
Print a Printer Settings page............................................................................................................ 4-9
Print Fonts ..................................................................................................................................... 4-10
Network default setting (For HL-5250DN) ..................................................................................... 4-11
Network default setting with APIPA protocol disabled (For HL-5250DN) ...................................... 4-11
v
5
Options
Lower tray unit (LT-5300) ...................................................................................................................... 5-1
DIMM ..................................................................................................................................................... 5-2
DIMM types ..................................................................................................................................... 5-2
Installing extra memory ................................................................................................................... 5-3
Print server (NC-2100p) (For HL-5240) ................................................................................................. 5-5
6
Routine Maintenance
Replacing the consumable items........................................................................................................... 6-1
Consumables................................................................................................................................... 6-1
Toner cartridge ................................................................................................................................ 6-2
Drum unit ......................................................................................................................................... 6-8
Replacing periodic maintenance parts................................................................................................. 6-12
Cleaning .............................................................................................................................................. 6-13
Cleaning the outside of the printer................................................................................................. 6-13
Cleaning the inside of the printer................................................................................................... 6-14
Cleaning the corona wire............................................................................................................... 6-17
7
Troubleshooting
Identifying your problem ........................................................................................................................ 7-1
Error messages in the Status Monitor ................................................................................................... 7-2
Error message printout .......................................................................................................................... 7-4
Paper handling ...................................................................................................................................... 7-5
Paper jams and how to clear them ........................................................................................................ 7-6
Improving the print quality.................................................................................................................... 7-13
Solving print problems ......................................................................................................................... 7-18
Network problems................................................................................................................................ 7-19
Other problems .................................................................................................................................... 7-19
For Macintosh® with USB.............................................................................................................. 7-19
Printing from DOS ........................................................................................................................ 7-19
BR-Script 3 .................................................................................................................................... 7-20
A
Appendix
Printer specifications.............................................................................................................................. A-1
Engine ............................................................................................................................................. A-1
Controller ......................................................................................................................................... A-2
Software .......................................................................................................................................... A-3
Control panel ................................................................................................................................... A-3
Paper handling ................................................................................................................................ A-3
Media specifications ........................................................................................................................ A-4
Supplies........................................................................................................................................... A-4
Dimensions / Weights...................................................................................................................... A-4
Other................................................................................................................................................ A-5
System Requirements ..................................................................................................................... A-5
Important information for choosing your paper................................................................................ A-6
Symbol and character sets .................................................................................................................... A-9
How to use the web browser ........................................................................................................... A-9
How to use the Remote Printer Console ......................................................................................... A-9
Symbol and character sets list....................................................................................................... A-10
vi
Quick reference for bar code control commands................................................................................. A-12
Print bar codes or expanded characters........................................................................................ A-12
B
Appendix (For Europe and Other Countries)
Brother Numbers ................................................................................................................................... B-1
Important information: Regulations........................................................................................................ B-2
Radio interference (220 to 240 volt model only).............................................................................. B-2
International ENERGY STAR® Compliance Statement .................................................................. B-2
IEC 60825-1 specification (220 to 240 volt model only) .................................................................. B-2
Internal laser radiation ..................................................................................................................... B-3
EU Directive 2002/96/EC and EN50419.......................................................................................... B-3
IMPORTANT - For Your Safety ....................................................................................................... B-4
EC Declaration of Conformity .......................................................................................................... B-5
C
Appendix (For USA and Canada)
Brother Numbers ...................................................................................................................................C-1
Important information: Regulations........................................................................................................C-3
Federal Communications Commission (FCC) Declaration of Conformity (For USA) ......................C-3
Industry Canada Compliance Statement (For Canada) ..................................................................C-4
International ENERGY STAR® Compliance Statement ..................................................................C-4
Laser Notices.........................................................................................................................................C-5
Laser Safety (110 to 120 volt model only) .......................................................................................C-5
FDA Regulations (110 to 120 volt model only) ................................................................................C-5
Internal laser radiation .....................................................................................................................C-5
IMPORTANT - For Your Safety .......................................................................................................C-6
D
Index
vii
1
About this Printer
What is in the box?
When you unpack the printer, make sure that you have all of the following parts.
Printer
CD-ROM
Quick Setup Guide
Drum unit and toner
cartridge assembly
AC power cord
Interface cable
An interface cable is not a standard accessory. Buy the proper interface cable for the interface you want to
use (USB, parallel or network).
„ USB cable
Do not use a USB interface cable that is longer than 6 feet (2.0 meters).
Do not connect the USB cable to a non-powered hub or a Macintosh® keyboard.
Make sure that you connect it to the USB connector of your PC.
USB is not supported under Windows® 95 or Windows NT® 4.0.
„ Parallel interface
Do not use a parallel interface cable that is longer than 6 feet (2.0 meters).
Use a shielded interface cable that is IEEE 1284-compliant.
„ Network cable (For HL-5250DN)
Use a straight-through Category5 (or greater) twisted-pair cable for 10BASE-T or 100BASE-TX Fast
Ethernet Network.
1-1
About this Printer
Front view
1
7
2
3
4
6
5
8
1 Front cover release button
2 Control panel
3 Face-down output tray support flap (support flap)
4 Front cover
5 Paper tray
6 Power switch
7 Face-down output tray
8 Multi-purpose Tray (MP Tray)
1-2
About this Printer
Back view
8
1
7
2
6
3
5
4
1 Back cover
2 Duplex Tray (For HL-5250DN)
3 AC power connector
4 HL-5250DN: Network status LEDs (Light Emitting Diodes)
5 HL-5250DN: 10/100BASE-TX port
6 USB interface connector
7 DIMM cover
8 Parallel interface connector
Note
The printer illustration is based on HL-5250DN.
1-3
About this Printer
Positioning the printer
Read the following before you use the printer.
Power supply
Use the printer within the recommended power range.
Power source:
USA and Canada:
AC 110 to 120 V, 50/60 Hz
Europe and Australia:
AC 220 to 240 V, 50/60 Hz
The power cord, including extensions, should be no longer than 5 meters (16.5 feet).
Do not share the same power circuit with other high-power appliances, such as an air conditioner, copier,
shredder and so on. If you cannot avoid using the printer with these appliances, we recommend that you use
a voltage transformer or a high-frequency noise filter.
Use a voltage regulator if the power source is not stable.
Environment
„ Put your printer on a flat, stable surface such as a desk that is free of vibration and shocks.
„ Put the printer near an AC power outlet, so that it can be easily unplugged from the AC power outlet if there
is an emergency.
„ Only use the printer within the following ranges of temperature and humidity:
Temperature: 10 ° C to 32.5 ° C (50 ° F to 90.5 ° F)
Humidity: 20% to 80% (without condensation)
„ Use the printer in a well-ventilated room.
„ DO NOT put the printer where the ventilation hole of the printer is blocked. Keep a gap of roughly 100 mm
(4 in.) between the ventilation hole and the wall.
„ DO NOT expose the printer to direct sunlight, excessive heat, moisture, or dust.
„ DO NOT put the printer near devices that contain magnets or produce magnetic fields.
„ DO NOT expose the printer to open/naked flames or salty or corrosive gasses.
„ DO NOT put objects on top of the printer.
„ DO NOT put the printer near heaters, air conditioners, water, chemicals or refrigerators.
„ Keep the printer horizontal when you carry it.
1-4
2
Printing Methods
About paper
Type and size of paper
The printer loads paper from the installed paper tray or the multi-purpose tray.
The names for the paper trays in the printer driver and this guide are as follows:
Paper tray
Tray 1
Multi-purpose tray
MP Tray
Optional lower tray unit
Tray 2 / Tray 3
Duplex tray for automatic duplex printing (For HL-5250DN)
DX
When looking at this page on the CD-ROM, you can jump to the page for each printing method by clicking p
in the table.
Media type
Tray 1
Tray 2/3
MP Tray
DX
Choose the media type
from the printer driver
Plain Paper
Plain paper
75 g/m2 to 105 g/m2
(20 to 28 lb)
p
p
p
p
Recycled paper
p
p
p
p
Bond paper
p
p
p
60 g/m 2 to
105 g/m2
(16 to 28 lb)
60 g/m2 to
105 g/m2
(16 to 28 lb)
60 g/m2 to
161 g/m 2
(16 to 43 lb)
Rough paper–
2
2
60 g/m to 161 g/m
(16 to 43 lb)
Bond Paper
Thin Paper
Thin paper
p
60 g/m2 to 75 g/m 2
(16 to 20 lb)
p
p
Thick Paper or Thicker
Paper
p
p
Transparencies
Up to 10 sheets
Up to 10 sheets
A4 or Letter
A4 or Letter
2
105 g/m to 161 g/m
(28 to 43 lb)
Transparency
Labels
p
p
Thick paper
2
Recycled Paper
p
Thicker Paper
A4 or Letter
Envelopes
Envelopes
p
Env. Thin
Env. Thick
2-1
Printing Methods
MP Tray
Paper size
Width: 69.9 to
215.9 mm (2.75 to
8.5 in.)
Tray 1
Tray 2, Tray 3
1
DX
1
A4, Letter, Legal ,
B5 (ISO), Executive,
A5, A6, B6 (ISO)
A4, Letter, Legal ,
B5 (ISO), Executive,
A5, B6 (ISO)
250 sheets
250 sheets
A4, Letter, Legal 1
Length: 116 to
406.4 mm (4.57 to
16 in.)
Number of sheets
(80 g/m2 to 21 lb)
1
50 sheets
Legal size paper is not available in some regions outside the USA and Canada.
Recommended paper
Plain paper
Europe
USA
Xerox Premier 80 g/m2
Xerox 4200DP 20 lb
Xerox Business 80 g/m2
Hammermill Laser Paper 24 lb
M-real DATACOPY 80 g/m2
Recycled paper
Xerox Recycled Supreme 80 g/m2
N/A
Transparency
3M CG3300
3M CG3300
Labels
Avery laser label L7163
Avery laser label #5160
„ Before you buy a lot of paper, test a small quantity to make sure that the paper is suitable.
„ Use paper that is made for plain-paper copying.
„ Use paper that is 75 to 90 g/m2 (20 to 24 lb).
„ Use neutral paper. Do not use acidic or alkaline paper.
„ Use long-grain paper.
„ Use paper with a moisture content of approximately 5%.
„ This printer can use recycled paper that meets DIN 19309 specifications.
CAUTION
DO NOT use ink jet paper because it may cause a paper jam or damage your printer.
Note
If you use paper that is not recommended, a paper jam or misfeed may occur in the printer.
To help you choose which paper to use with this printer, see Important information for choosing your paper
on page A-6.
2-2
Printing Methods
Types of envelopes
Most envelopes will be suitable for your printer. However, some envelopes may have feed and print quality
problems due to the way they have been made. A suitable envelope should have edges with straight, wellcreased folds and the leading edge should not be thicker than two pieces of paper. The envelope should lie
flat and not be of baggy or flimsy construction. You should buy quality envelopes from a supplier who
understands that you will be using the envelopes in a laser printer. Before you print a lot of envelopes, test
one to make sure that the print results are what you want.
Brother does not recommend a particular envelope because envelope manufacturers may change the
envelope specifications. You are responsible for the quality and performance of the envelopes you use.
„ Do not use damaged, curled, wrinkled, irregularly shaped, extremely shiny or textured envelopes.
„ Do not use envelopes with clasps, snaps, tie strings, self-adhesive components, windows, holes, cutouts
or perforations.
„ Do not use envelopes that are of a baggy construction, not sharply creased, embossed (have raised
writing on them) or pre-printed on the inside.
„ Do not use envelopes that were previously printed by a laser printer.
„ Do not use envelopes that cannot be arranged when put in a pile.
„ Do not use envelopes that are made of paper that weighs more than the paper weight specifications for
the printer.
„ Do not use envelopes that have been badly made, with edges that are not straight or consistently square.
If you use any of the types of envelopes listed above, they may damage your printer. This damage is not
covered under any Brother warranty or service agreement.
Note
• Do not put different types of paper in the paper tray at the same time because it may cause paper jams or
misfeeds.
• Do not print envelopes using duplex printing.
• For proper printing, you must choose the same paper size from your application as the paper in the tray.
2-3
Printing Methods
Printable area
When using PCL (standard driver) emulation, the edges of the paper that cannot be printed on are shown in
the tables below.
Note
When using BR-Script emulation, the edges of the paper that cannot be printed on are 4.32 mm (0.17 in.).
Portrait
1
2
4
3
A4
Letter
Legal
B5 (ISO)
Executive
A5
A6
B6
1
4.23 mm
(0.16 in.)
4.23 mm
(0.16 in.)
4.23 mm
(0.16 in.)
4.23 mm
(0.16 in.)
4.23 mm
(0.16 in.)
4.23 mm
(0.16 in.)
4.23 mm
(0.16 in.)
4.23 mm
(0.16 in.)
2
6.01 mm
(0.24 in.)
6.35 mm
(0.25 in.)
6.35 mm
(0.25 in.)
6.01 mm
(0.24 in.)
6.35 mm
(0.25 in.)
6.01 mm
(0.24 in.)
6.01 mm
(0.24 in.)
6.01 mm
(0.24 in.)
3
4.23 mm
(0.16 in.)
4.23 mm
(0.16 in.)
4.23 mm
(0.16 in.)
4.23 mm
(0.16 in.)
4.23 mm
(0.16 in.)
4.23 mm
(0.16 in.)
4.23 mm
(0.16 in.)
4.23 mm
(0.16 in.)
4
6.01 mm
(0.24 in.)
6.35 mm
(0.25 in.)
6.35 mm
(0.25 in.)
6.01 mm
(0.24 in.)
6.35 mm
(0.25 in.)
6.01 mm
(0.24 in.)
6.01 mm
(0.24 in.)
6.01 mm
(0.24 in.)
Landscape
1
2
4
3
A4
Letter
Legal
B5 (ISO)
Executive
A5
A6
B6
1
4.23 mm
(0.16 in.)
4.23 mm
(0.16 in.)
4.23 mm
(0.16 in.)
4.23 mm
(0.16 in.)
4.23 mm
(0.16 in.)
4.23 mm
(0.16 in.)
4.23 mm
(0.16 in.)
4.23 mm
(0.16 in.)
2
5.0 mm
(0.19 in.)
5.08 mm
(0.2 in.)
5.08 mm
(0.2 in.)
5.0 mm
(0.19 in.)
5.08 mm
(0.2 in.)
5.0 mm
(0.19 in.)
5.0 mm
(0.19 in.)
5.0 mm
(0.19 in.)
3
4.23 mm
(0.16 in.)
4.23 mm
(0.16 in.)
4.23 mm
(0.16 in.)
4.23 mm
(0.16 in.)
4.23 mm
(0.16 in.)
4.23 mm
(0.16 in.)
4.23 mm
(0.16 in.)
4.23 mm
(0.16 in.)
4
5.0 mm
(0.19 in.)
5.08 mm
(0.2 in.)
5.08 mm
(0.2 in.)
5.0 mm
(0.19 in.)
5.08 mm
(0.2 in.)
5.0 mm
(0.19 in.)
5.0 mm
(0.19 in.)
5.0 mm
(0.19 in.)
2-4
Printing Methods
Printing methods
Printing on plain paper, bond paper and transparencies
Printing on plain paper, bond paper or transparencies from Tray 1, 2 or 3
For the proper paper to use, see About paper on page 2-1.
a
Choose the following from the printer driver:
Paper Size ............................ (1)
Media Type ........................... (2)
Paper Source ....................... (3)
and any other settings.
„ Windows printer driver
1
2
3
„ BR-Script printer driver
1
3
2
2-5
Printing Methods
b
Pull the paper tray completely out of the printer.
c
While pressing the blue paper-guide release lever, slide the paper guides to fit the paper size. Make sure
that the guides are firmly in the slots. For legal size paper 1, press in the paper-guide release lever and
pull out the back of the paper tray.
1
d
Legal size paper is not available in some regions outside the USA and Canada.
Put paper in the tray, and below the maximum paper mark (b).
2-6
Printing Methods
e
f
Put the paper tray firmly back in the printer. Make sure that it is completely inserted into the printer.
g
Send the print data to the printer.
Lift up the support flap to prevent paper from sliding off the face-down output tray, or remove each page
as soon as it comes out of the printer.
Note
• The side to be printed on must be face down.
• When printing on transparencies, remove each transparency at once after printing. Stacking the printed
transparencies may cause a paper jam or the transparency to curl.
2-7
Printing Methods
Printing on plain paper, bond paper or transparencies from the MP tray
MP Tray mode is automatically turned on when paper is put in the multi-purpose tray.
For the proper paper to use, see About paper on page 2-1.
a
Choose the following from the printer driver:
Paper Size ............................ (1)
Media Type ........................... (2)
Paper Source ....................... (3)
and any other settings.
„ Windows printer driver
1
2
3
„ BR-Script printer driver
1
3
2
2-8
Printing Methods
b
Open the MP tray and lower it gently.
c
Pull out the MP tray support flap (1).
1
d
Lift up the support flap to prevent paper from sliding off the face-down output tray, or remove each page
as soon as it comes out of the printer.
2-9
Printing Methods
e
Put paper in the MP tray. Make sure that the paper stays under the maximum paper mark (b) on both
sides of the tray.
f
While pressing the paper-guide release lever, slide the paper guide to fit the paper size.
g
Send the print data to the printer.
Note
• The side to be printed on must be face up with the leading edge (top of the paper) in first.
• When printing on transparencies, remove each transparency at once after printing. Stacking the printed
transparencies may cause a paper jam or the transparency to curl.
2 - 10
Printing Methods
Printing on thick paper, labels and envelopes
MP Tray mode is automatically turned on when paper is put in the multi-purpose tray.
For the proper paper to use, see About paper on page 2-1 and Types of envelopes on page 2-3.
a
Choose the following from the printer driver:
Paper Size ............................ (1)
Media Type ........................... (2)
Paper Source ....................... (3)
and any other settings.
„ Windows printer driver
1
2
3
„ BR-Script printer driver
1
3
2
Note
• When you use Envelope #10, choose Com-10 in Paper Size.
• For other envelopes which are not listed in the printer driver, such as Envelope #9 or Envelope C6,
choose User Defined... For more information on the envelope size, see Paper size on page A-8.
2 - 11
Printing Methods
b
Open the MP tray and lower it gently.
c
Pull out the MP tray support flap (1).
1
d
Lift up the support flap to prevent paper from sliding off the face-down output tray, or remove each page
as soon as it comes out of the printer.
2 - 12
Printing Methods
e
Put paper in the MP tray. Make sure that the paper stays under the maximum paper mark (b) on both
sides of the tray.
Note
• Envelope joints that are sealed by the manufacturer should be secure.
• The side to be printed on must be face up.
• All sides of the envelope should be properly folded without wrinkles or creases.
f
While pressing the paper-guide release lever, slide the paper guide to fit the paper size.
g
Send the print data to the printer.
Note
• Remove each sheet or envelope at once after printing. Stacking the sheets or envelopes may cause the
paper to jam or curl.
• If envelopes get smudged during printing set the Media Type to Thick Paper or Thicker Paper to
increase the fixing temperature. To adjust the print density setting, see Printing on thick paper, labels and
envelopes on page 2-11.
• If the envelopes is creased after they are printed, see Improving the print quality on page 7-13.
2 - 13
Printing Methods
Note
• If the DL size double flap envelope is creased after printing, choose DL Long Edge in Paper Size, from
the Basic tab. Put a new DL size double-flap envelope in the MP tray with the longest edge of the envelope
in first, then print again.
• When you put paper in the MP tray, remember the following:
• Put the leading edge (top of the paper) in first and push it gently into the tray.
• Make sure that the paper is straight and in the proper position in the MP tray. If it is not, the paper may
not be fed properly, resulting in a skewed printout or a paper jam.
2 - 14
Printing Methods
Duplex Printing
The supplied printer drivers for Windows® 95/98/Me/2000/XP and Windows NT® 4.0, Mac OS® 9.1 to 9.2 and
Mac OS® X 10.2.4 or greater all enable duplex printing. For more information about how to choose the
settings, see the Help text in the printer driver.
Guidelines for printing on both sides of the paper
„ If the paper is thin, it may wrinkle.
„ If paper is curled, straighten it and then put it back in the paper tray or the MP tray.
„ If the paper is not feeding properly, it may be curled. Remove the paper and straighten it.
„ When you use the manual duplex function, it is possible that there may be paper jams or poor print quality.
If there is a paper jam, see Paper jams and how to clear them on page 7-6. If you have a print quality
problem, see Improving the print quality on page 7-13.
Manual duplex printing
„ The BR-Script printer driver (PostScript® 3™ emulation) does not support manual duplex printing.
„ Use plain paper or recycled paper. Do not use bond paper.
Manual duplex printing from the paper tray
a
In the printer driver choose the Advanced tab, then choose the Manual Duplex printing mode, and from
the Basic tab choose the Paper Source to be Tray1.
b
Send the data to the printer.
The printer will automatically print all the even-numbered pages on one side of the paper first.
c
Remove the printed even-numbered pages from the output tray and put them back in the paper tray with
the side to be printed on (blank side) face down. Follow the instructions on the PC screen.
d
The printer will now automatically print all the odd-numbered pages on the other side of the paper.
2 - 15
Printing Methods
Note
• If you choose the Paper Source to be Auto Select, put the printed even-numbered pages in the MP tray.
• When you put paper in the paper tray, first empty the tray. Next, put the printed pages in the tray, with the
printed side face up. (Do not add the printed pages to the top of a stack of unprinted paper.)
Manual duplex printing from the MP tray
Note
Before putting the sheets back in the MP tray, you will have to straighten them or you may get paper jams.
a
From the Advanced tab choose the Manual Duplex printing mode, and from the Basic tab choose the
Paper Source to be MP Tray.
b
Put the paper in the MP tray with the side to be printed on first facing up. Follow the instructions on the
PC screen. Repeat this step until you have printed all the even-numbered pages.
c
Remove the printed even-numbered pages from the output tray and then, in the same order, put them
back into the MP tray. Put the paper with the side to be printed on (the blank side) face up. Follow the
instructions on the PC screen.
d
Repeat c until you have printed all the odd-numbered pages on the other side of the paper.
2 - 16
Printing Methods
Paper orientation for manual duplex printing
The printer prints the second page first.
If you print 10 pages on 5 sheets of paper, it will print page 2 and then page 1 on the first sheet of paper. It
will print page 4 and then page 3 on the second sheet of paper. It will print page 6 and then page 5 on the
third sheet of paper, and so on.
When doing manual duplex printing, the paper must be put in the paper tray in the following way:
„ For the paper tray:
• Put the side to be printed on face down with the leading edge (top) of the paper at the front of the tray.
• To print on the second side, put the paper face up, with the leading edge (top) of the paper at the front
of the tray.
• If letterhead paper is used, put the paper in the tray with the heading face up at the front of the tray.
• To print on the second side, put the heading face down at the front of the tray.
„ For the multi-purpose tray (MP tray):
• Put the side to be printed on face up with the leading edge (top) of the paper in first.
• To print on the second side, put the paper face down, with the leading edge (top) of the paper in first.
• If letterhead paper is used, put it in with the heading face down and in first.
• To print on the second side, put the heading face up and in first.
2 - 17
Printing Methods
Automatic duplex printing (For HL-5250DN)
Note
• The screens in this section are from Windows® XP. The screens on your PC may vary depending on your
operating system.
• Use A4, Letter or Legal size paper when you use the automatic duplex printing function.
• Make sure that the back cover is closed.
• Make sure that the duplex tray is installed correctly in the printer.
• If paper is curled, straighten it and then put it back in the paper tray.
• You should use regular paper. Do not use bond paper or thin paper.
a
b
Put paper in the paper tray or MP tray.
For the Windows printer driver
1
Open the Properties dialog box in the printer driver.
2
From the General tab, click the Printing Preferences icon.
3
From the Advanced tab, click the Duplex icon.
4
Make sure that Use Duplex Unit has been chosen.
5
Click OK. The printer will print on both sides of the paper automatically.
For the BR-Script printer driver
1
Open the Properties dialog box in the printer driver.
2
From the General tab, click the Printing Preferences icon.
3
From the Layout tab, choose Orientation, Print on Both Sides (Duplex) and Page Order.
2 - 18
Printing Methods
4
Click OK. The printer will print on both sides of the paper automatically.
Booklet printing (For Windows printer driver)
a
b
c
d
Put paper in the paper tray or MP tray.
e
Click OK. The printer will print a booklet automatically.
Open the Properties dialog box in the printer driver.
From the General tab, choose the Printing Preferences icon.
From the Advanced tab, choose Duplex and Use Duplex Unit or Manual Duplex, and then choose
Booklet Printing.
2 - 19
3
Driver and Software
Printer driver
A printer driver is software that translates data from the format used by a computer to the format that a
particular printer needs. Typically, this format is a printer command language (PCL) or page description
language (PDL).
The printer drivers for the following version of Windows® and Macintosh® are on the CD-ROM we have
supplied. Install the drivers by following the Quick Setup Guide. The latest printer driver can be downloaded
from the Brother Solutions Center at http://solutions.brother.com.
If you want to uninstall the printer driver, see Uninstalling the printer driver on page 3-18.
For Windows®
„ Windows printer driver (Hewlett-Packard® laser printer compatible driver)
„ BR-Script (PostScript®3™ language emulation) printer driver
„ Generic PCL Driver (For users of Citrix® MetaFrame®, Windows® Terminal Server environments and other Windows
NT 4.0® and Windows® 2000/XP network shared environments, we recommend the use of our generic PCL Driver.
This driver only supports basic printing functions.)
For Macintosh®
„ Brother Laser driver for Macintosh®
„ BR-Script (PostScript®3™ language emulation) printer driver
For Linux
„ LPR printer driver
„ CUPS printer driver
Note
• For more infomation about the generic PCL Driver and Linux printer driver, visit us at http://solutions.brother.com.
• The printer driver for Linux may be released after the initial release of this product.
Windows® 95/98/Me
Windows
printer driver
BR-Script
printer driver
p
p
p
p
p
p
Generic PCL
Driver
Brother Laser LPR / CUPS
driver
printer driver
Windows NT® 4.0
Windows® 2000 Professional
Windows® XP Home Edition
Windows® XP Professional
Windows® XP Professional x64
Edition
Mac OS® 9.1 to 9.2
Mac OS® X 10.2.4 or greater
Linux (Mandrake, Red Hat,
SuSE Linux, Debian)
p
p
p
p
3-1
Driver and Software
You can change the following printer settings when you print from your computer.
„ Paper Size
„ Multiple Page
„ Orientation
„ Copies
„ Media Type
„ Paper Source
„ Resolution
„ Toner Save Mode
„ Duplex printing (Manual Duplex printing 1 3 / Duplex printing with Duplex tray 4)
„ Watermark 1 3
„ Job Spooling 1 3
„ Quick Print Setup 1 3
„ Sleep Time
„ Status Monitor 1
„ Macro 1 3
„ Administrator 1 2 3
„ Insert Command/File 1 2 3
„ Page Protection 1 3
„ Print Date & Time 1 3
„ Density adjustment 1 3
„ Error Message Printout 1 3
1
These settings are not available with the BR-script printer driver for Windows®.
2
These settings are not available with Windows NT® 4.0 and Windows® 2000/XP.
3
These settings are not available with Brother Laser driver and BR-Script printer driver for Macintosh®.
4
This setting is not available for HL-5240.
3-2
Driver and Software
Features in the printer driver (For Windows®)
For more information, see the Help text in the printer driver.
Note
• The screens in this section are from Windows® XP. The screens on your PC will vary depending on your
operating system.
• If you are using Windows® 2000 or XP, you can access the Printing Preferences dialog box by clicking
Printing Preferences... in the General tab of the Printer Properties dialog box.
• If you are using Windows NT® 4.0, you can access the Printing Preferences dialog box by clicking
Document Defaults... from the File menu of the Printers folder.
Basic tab
You can also change settings by clicking the illustration on the left side of the Basic tab.
a
b
Choose the Paper Size, Multiple Page, Orientation and other settings (1).
Choose the Duplex / Booklet setting from None, Duplex or Booklet (2).
Note
You can choose more detailed settings for Duplex or Booklet printing in the the Advanced tab. See Duplex
Printing on page 3-6.
c
d
Choose the Paper Source (3).
Click OK to apply your chosen settings.
To return to the default settings, click Default, then OK.
1
2
3
3-3
Driver and Software
Advanced tab
1
2
3
4
5
Change the tab settings by clicking one of the following icons:
„ Print Quality (1)
„ Duplex Printing (2)
„ Watermark (3)
„ Page Setting (4)
„ Device Options (5)
Print Quality
„ Resolution
You can change the resolution as follows:
• 1200 dpi
• HQ 1200
• 600 dpi
• 300 dpi
Note
If you use the high quality 1200 dpi setting (1200 × 1200 dpi) the print speed will be slower.
3-4
Driver and Software
„ Toner Save Mode
You can save running costs by turning on the Toner Save Mode, which reduces the print density.
Note
• We do not recommend Toner Save for printing Photo or Gray Scale images.
• Toner Save Mode is not available for 1200 dpi or HQ 1200 resolution.
„ Print Setting
You can manually change the print setting.
• Auto
Choosing Auto will allow automatic printing with the most suitable print settings for your print job.
• Manual
You can change the settings manually by choosing Manual and clicking the Setting... button.
You can set brightness, contrast and other settings.
Duplex Printing
„ Use Duplex Unit (For HL-5250DN)
If you choose Use Duplex Unit button, the dialog box for the duplex settings will appear. There are six
types of duplex binding directions available for each orientation, automatically.
„ Manual Duplex
If you choose Manual Duplex button, the dialog box for the manual duplex settings will appear. There are
six types of manual duplex binding directions available for each orientation.
„ Booklet Printing
When you want to print a booklet, use this function. To make the Booklet, fold the printed pages down the
middle, when using the booklet printing function.
„ Binding Offset
If you check the Binding Offset option, you can also specify the offset for binding in inches or millimeters.
Watermark
You can put a logo or text into your documents as a watermark.
You can choose one of the preset watermarks, or you can use a bitmap file or text file that you have created.
When you use a bitmap file as a watermark, you can change the size of the watermark and put it anywhere
you like on the page.
When you use text as a watermark, you can change the font, darkness and angle settings.
Page Setting
You can change the print image scaling and choose Mirror/Reverse print options.
3-5
Driver and Software
Device Options
You can set the following in Printer Function:
(You can jump to the page for each Printer Function by choosing the function name in the list below.)
„ Job Spooling
„ Quick Print Setup
„ Sleep Time
„ Status Monitor
„ Macro
„ Administrator (For Windows® 95/98/Me only)
„ Insert Command/File (For Windows® 95/98/Me only)
„ Page Protection
„ Print Date & Time
„ Density adjustment
„ Error Message Printout
Note
The Printer Function list may vary depending on the model.
3-6
Driver and Software
„ Job Spooling
The printer keeps the last print job sent to it in memory.
To reprint the last document, press Go and hold it down for about 4 seconds until all the LEDs light up in
order (Toner, Drum, Paper, Status), and then release Go. Within 2 seconds press Go the number of
times you want to reprint. If you don’t press Go within 2 seconds, a single copy will be printed.
Note
If you want to prevent other people from printing your data using the reprint function, uncheck the
Use Reprint check box in the job spooling settings.
„ Quick Print Setup
This feature allows you to quickly choose driver settings. To view settings, click the tasktray icon.
You can turn the quick print setup function on or off. A small selection window appears on your PC. This
will then let you make changes to the settings of the following functions:
• Multiple Page
• Duplex Printing
• Toner Save Mode
• Paper Source
• Media Type
„ Sleep Time
When the printer does not receive data for a certain period of time, it enters sleep mode. In sleep mode,
the printer acts as though it were turned off. When you choose Printer Default the timeout setting will be
5 minutes. Intelligent Sleep Mode automatically adjusts to the most suitable timeout setting depending on
the frequency of your printer use. While the printer is in sleep mode, all the LEDs are off, but the printer
can still receive data. Receiving a print file or document or pressing Go will automatically wake up the
printer to start printing.
To turn sleep mode off, from the Advanced tab, click the Device Options icon and choose Sleep Time.
Double-click the word Sleep Time, and the Sleep Time Off function will appear. Click Off to stop the
printer going into sleep mode. The Sleep Time Off function can be hidden by double-clicking the word
Sleep Time again. We recommend that you keep sleep mode on for power saving.
„ Status Monitor
This reports the printer status (any errors that may happen with the printer) when printing. The default
setting for the Status Monitor is off. If you want to turn the status monitor on, from the Advanced tab, click
the Device Options icon and then choose Status Monitor.
„ Macro
You can save a page of a document as a macro to printer memory. You can also execute the saved macro
(you can use the saved macro as an overlay on any documents). This will save time and increase printing
speed for often used information such as forms, company logos, letterhead formats or invoices.
3-7
Driver and Software
„ Administrator (For Windows® 95/98/Me only)
Administrators have the authority to limit the number of copies, scaling setting and watermark setting
functions.
• Password
Enter the password into this box.
• Set Password
Click here to change the password.
• COPY LOCK
Lock the copy pages selection to prevent multiple copy printing.
• WATERMARK LOCK
Lock the current settings of the Watermark option to prevent changes being made.
• SCALING LOCK
Lock the scaling setting as shown below:
1 in 1
100%
„ Insert Command/File (For Windows® 95/98/Me only)
This function lets you to do the following:
• Put a print file or tiff format file into a print job.
• Put a text string into a print job.
• Put a macro, which is saved in printer memory, into a print job.
„ Page Protection
Page Protection refers to a setting that reserves extra memory for the creation of full-page images.
Selections are AUTO, OFF and Printer Default.
The page protection feature allows the printer to create the full-page image to be printed in memory before
physically moving the paper through the printer. Use this function when the image is complicated and the
printer has to wait to process the image before printing.
„ Print Date & Time
When this feature is enabled, the date and time will print on your document.
„ Density adjustment
Increase or decrease the print density.
Note
The Density adjustment is not available when you set the resolution to HQ 1200.
„ Error Message Printout
You can choose whether the printer reports problems by printing an error page. For details, see Error
message printout on page 7-4.
Selections are Printer Default (ON), ON and OFF.
3-8
Driver and Software
Accessories tab
Note
From the Start menu, select Control Panel and then Printers 1. Right-click the Brother HL-5240/5250DN
series icon and select Properties. You can access the Accessories tab from the Printer Properties
dialog box.
1
Printers and Faxes for Windows ® XP users.
1
3
2
„ Available Options (1)
You can manually add and remove the options that are installed on the printer.
„ Paper Source Setting (2)
This feature identifies the paper size defined for each paper tray.
• Paper Size
This setting allows you to define which paper size is used for each tray. Highlight the tray you want to define and
then choose the paper size from the pull-down menu. Click Update to apply the setting to the tray. When using
more than one paper size you must define the paper size for each tray so the paper is pulled from the correct tray.
• Default Source
This setting allows you to choose the default paper source that your document will be printed from. Choose the
Default Source from the pull-down menu and click Update to save your setting. The Auto Select setting will
automatically pull paper from any tray that has a defined paper size that matches your document.
„ Auto detection of printer options (3)
The Auto Detect function finds the currently installed optional unit devices and shows the available
settings in the printer driver. When you click Auto Detect, options that are installed on the printer will be
listed. You can manually add or remove options.
Note
The Auto Detect function is not available under certain printer conditions.
3-9
Driver and Software
Support tab
3
1
2
4
5
6
„ Version (1)
Displays the printer driver version.
„ Web Update (2)
You can check the Brother web site for updated drivers, and automatically download and update the
printer driver on your PC.
„ Brother Solutions Center (3)
The Brother Solutions Center (http://solutions.brother.com) is a web site offering information about your
Brother product including FAQs (Frequently Asked Questions), User’s Guides, driver updates and tips for
using your printer.
„ Print Settings (4)
This will print the pages that show how the internal settings of the printer have been configured.
„ Print Fonts (5)
This will print the pages that show all the internal fonts of the printer.
„ Check Setting... (6)
This will show the current settings of the printer driver.
3 - 10
Driver and Software
Features in the BR-Script (PostScript® 3™ language emulation) printer driver
(For Windows®)
For more information, see the Help text in the printer driver.
Note
The screens in this section are based on HL-5250DN with Windows® XP.
The screens on your PC may vary depending on the printer model and your operating system.
Device Settings tab
Choose the options you have installed.
3 - 11
Driver and Software
Printing Preferences
Note
If you are using Windows NT® 4.0, Windows ® 2000 or XP, you can access the Printing Preferences dialog
box by clicking Printing Preferences... in the General tab of the Brother HL-5240/HL-5250DN
BR-Script3 Properties dialog box.
„ Layout tab
You can change the layout setting by choosing the settings for Orientation,
Print on Both Sides (Duplex), Page Order and Pages Per Sheet.
„ Paper/Quality tab
Choose the Paper Source.
3 - 12
Driver and Software
Advanced options
1
2
3
a
b
c
Choose the Paper Size and Copy Count (1).
Set the Scaling and TrueType Font settings (2).
You can change settings by choosing the setting in the Printer Features list (3):
„ Print Quality
„ Media Type
„ Toner Save
You can save running costs by turning on the Toner Save, which reduces the print density.
„ Sleep Time
See Device Options on page 3-7.
„ Halftone Screen Lock
„ BR-Script Level
3 - 13
Driver and Software
Features in the printer driver (For Macintosh®)
This printer supports Mac OS® 9.1 to 9.2 and Mac OS® X 10.2.4 or greater.
Note
The screens in this section are from Mac OS® X 10.4. The screens on your Macintosh® will vary depending
on your operating system.
Page Setup
You can set the Paper Size, Orientation and Scale.
Layout
Set the Pages per Sheet, Layout direction and Border.
„ Pages per Sheet
Choose how many pages will appear on each side of the paper.
„ Layout Direction
When you specify the pages per sheet, you can also specify the direction of the layout.
„ Border
If you want to add a border, use this function.
3 - 14
Driver and Software
Print Settings
You can change settings by choosing the setting in the Print Settings list:
Basic tab
„ Resolution
You can change the resolution as follows:
• 300 dpi
• 600 dpi
• HQ 1200
• 1200 dpi
Note
If you use the high quality 1200 dpi setting (1200 × 1200 dpi) the print speed will be slower.
„ Media Type
You can change the media type as follows:
• Plain Paper
• Thin Paper
• Thick Paper
• Thicker Paper
• Bond Paper
• Transparencies
• Envelopes
• Env.Thick
• Env.Thin
• Recycled Paper
„ Toner Save Mode
You can save running costs by turning on Toner save, which reduces the print density.
Note
• We do not recommend Toner Save for printing Photo or Gray Scale images.
• Toner Save Mode is not available for 1200 dpi or HQ 1200 resolution.
3 - 15
Driver and Software
Advanced tab
„ Print Quality
You can change the print quality as follows:
• Brother Photo
This is a photograph mode (gradation priority). Choose this setting for printing photographs that have
continuous gradation. You can represent soft contrasts between various shades of gray.
• Brother Graphics
This is a graphics mode (contrast priority). Choose this setting for printing text and figures, such as
business and presentation documents. You can represent sharp contrasts between shaded areas.
• Generic
This is a standard halftone pattern of Mac® OS X. If you choose this mode for printing text documents,
the print speed will be faster. Use this mode for Mac®s that have less memory.
„ Sleep Time
When the printer does not receive data for a certain period of time (timeout), it enters sleep mode. In sleep
mode, the printer acts as though it were turned off. The default timeout is 5 minutes. While the printer is in
sleep mode, all the LEDs are off, but the printer can still receive data. Receiving a print file or document
or pressing Go will automatically wake up the printer to start printing.
Status Monitor (For Mac® X 10.2.4 or greater users)
This reports the printer status (any errors that may happen with the printer) when printing. If you would like to
turn the status monitor on, run the BrStatusMonitor.app (from the Macintosh HD (Startup Disk), choose
Library, Printers, Brother, Utilities).
3 - 16
Driver and Software
Uninstalling the printer driver
You can uninstall the printer driver that you installed with the following steps.
Note
• This is not available if you installed the printer driver from the Windows Add a printer function.
• After uninstalling, we recommend that you restart your computer to remove files that were in use during
the uninstall.
Printer driver for Windows®
For Windows® XP
a
b
c
Click the Start button, point to All Programs and then to your printer name.
Click UnInstall.
Follow the instructions on the screen.
For Windows® 95/98/Me/2000 and Windows NT ® 4.0
a
b
c
Click the Start button, point to Programs and then to your printer name.
Click UnInstall.
Follow the instructions on the screen.
3 - 17
Driver and Software
Brother Laser driver for Macintosh®
For Mac OS® X 10.2.4 or greater
a
b
c
d
Disconnect the USB cable between the Macintosh and your printer.
e
Drag the HL-MFLPro folder (from the Macintosh HD (Startup Disk), choose Library, Printers,
Brother) into the Trash and then empty the Trash.
f
Restart the Macintosh®.
1
Restart the Macintosh®.
Log on as an ‘Administrator’.
Run the Printer Setup Utility 1 (from the Go menu, choose Applications, Utilities), then choose the
printer you want to remove and remove it by clicking the Delete button.
Print Center for Mac OS® X 10.2 users
For Mac OS® 9.1 to 9.2
a
b
Open the Extensions folder located in the System Folder on the Macintosh HD.
Drag all these following files in the Extensions folder to the trash.
„ BR_PrintMonitor(laser)
„ Brother Laser
„ Brother Laser(IP)
Note
There may be several USB Print Driver(BRXXX) 1 and BR_PrintMonitor(BXX) 1 extensions with different
endings.
1
c
d
The ‘x’ refers to the model of your machine.
Restart the Macintosh®.
Once the computer has restarted you can then empty the trash.
3 - 18
Driver and Software
Software
Software for networks (For HL-5250DN only)
BRAdmin Professional (For Windows®)
The BRAdmin Professional is a utility for managing your Brother network enabled printers that are running
under Windows® 95/98/Me/2000/XP and Windows NT ® 4.0. It allows you to easily configure and check the
status of your printer on the network.
BRAdmin Light (For Macintosh®)
The Brother BRAdmin Light software is a Java™ application that is designed for the Apple® Mac OS®X
environment. It supports some of the features of the Windows® BRAdmin software. For example, using the
BRAdmin Light software, you can change some network settings and update firmware on Brother’s network
ready printers and multifunction devices.
Driver Deployment Wizard (For Windows®)
This installer includes the Windows® printer driver and Brother network port driver (LPR and NetBIOS). If the
administrator installs the printer driver and port driver using this application, the administrator can save the
file to the file server or send the file by e-mail to users. Then, each user just clicks that file to have the printer
driver, port driver, IP address, and so on, automatically copied to their PC.
Network Print Software (For Windows®)
This installer includes the port monitors (Peer-to-Peer Printing software). They allow you to print through the
network (LAN) under Windows®
Web BRAdmin (For Windows®)
The Web BRAdmin is designed to manage all LAN/WAN Brother network connected devices. By installing
the Web BRAdmin server utility on a PC running IIS 1, administrators with a web browser can connect to the
Web BRAdmin server, which then communicates with the device itself. Unlike the BRAdmin Professional,
which is designed for Windows® systems only, the Web BRAdmin server utility can be accessed from any
client PC with a web browser that supports Java 2.
You can download the Web BRAdmin from our web site. Visit us at http://solutions.brother.com.
1
Internet Information Server 4.0 or 5.0
Web BRAdmin and Internet Information Server 4.0 are supported by the following operating systems:
„ Windows NT® 4.0 Server
Web BRAdmin and Internet Information Service 5.0 are supported by the following operating systems:
„ Windows® 2000 Server
„ Windows® 2000 Advanced Server
„ Windows® 2000 Professional
Web BRAdmin and Internet Information Service 5.1 are supported by the following operating systems:
„ Windows® XP Professional
3 - 19
Driver and Software
About emulation modes
This printer has the following emulation modes. You can change the setting using Remote Printer Console
or a Web browser.
„ HP LaserJet Mode
The HP LaserJet mode (or HP mode) is the emulation mode in which this printer supports the PCL6
language of the Hewlett-Packard® LaserJet laser printer. Many applications support this type of laser
printer. Using this mode will allow your printer to run at its best with those applications.
„ BR-Script 3 Mode
BR-Script is an original Brother page description language and a PostScript® language emulation
interpreter. This printer supports level 3. The BR-Script interpreter of this printer allows you to control text
and graphics on pages.
For technical information about PostScript® commands, see the following manuals:
• Adobe Systems Incorporated. PostScript® Language Reference, 3rd edition. Addison-Wesley
Professional, 1999. ISBN: 0-201-37922-8
• Adobe Systems Incorporated. PostScript® Language Program Design. Addison-Wesley Professional,
1988. ISBN: 0-201-14396-8
• Adobe Systems Incorporated. PostScript® Language Tutorial and Cookbook. Addison-Wesley
Professional, 1985. ISBN: 0-201-10179-3
„ EPSON FX-850 and IBM Proprinter XL Mode
The EPSON FX-850 and IBM Proprinter XL modes are the emulation modes that this printer supports to
meet the industry-standard for dot matrix printers. Some applications support these dot matrix printer
emulations. Use these emulation modes so your printer will work well when printing from those types of
applications.
Automatic emulation selection
This printer has an automatic emulation selection feature that is turned on by default. This lets it automatically
change the emulation mode to suit the type of data it receives.
You can change the setting using Remote Printer Console or a Web browser.
The printer can choose from the following combinations:
Setting 1 (default)
Setting 2
HP LaserJet
HP LaserJet
BR-Script 3
BR-Script 3
EPSON FX-850
IBM ProPrinter XL
3 - 20
Driver and Software
Automatic interface selection
This printer has an automatic interface selection feature that is turned on by default. This lets it automatically
change the interface to IEEE 1284 parallel, USB, or Ethernet depending on which interface is receiving data.
When you use the parallel interface, you can turn the high-speed and bi-directional parallel communications
on or off by using Remote Printer Console. (See Remote Printer Console on this page.) Since the default
setting is on for the automatic interface selection mode, simply connect the interface cable to the printer.
Always turn off both your computer and printer when connecting or disconnecting the cable.
Note
This function takes a few seconds to work. If you want to speed up printing, choose the required interface
manually by using Remote Printer Console. (See Remote Printer Console on this page.)
If you typically use only one interface, we recommend that you choose that interface using Remote Printer
Console. (See Remote Printer Console on this page.). If only one interface is chosen, the printer will allocate
the entire input buffer to that interface.
Remote Printer Console
Remote Printer Console is software to change many of the printer settings independently of your application.
For example, you can change the settings for printer margin, sleep mode, character set and so on. These
settings are then remembered and used by the printer.
How to use and install the Remote Printer Console software
To use the Remote Printer Console software, follow the steps below.
For Windows®
a
b
c
d
Put the CD-ROM into your CD-ROM drive and close the opening screen when it appears.
Open Windows ® Explore and choose the CD-ROM drive.
Double-click the RPC folder.
Refer to the RPC_User’s_Guide.pdf for how to install and use the Remote Printer Console.
For Macintosh®
a
b
c
Put the CD-ROM into your CD-ROM drive. Double-click the HL5200 icon on the desktop.
Double-click the RPC folder.
Refer to the RPC_User’s_Guide.pdf for how to install and use the Remote Printer Console.
3 - 21
4
Control Panel
LEDs (Light Emitting Diodes)
This section refers to the four LEDs Toner, Drum, Paper and Status, and two buttons Go and Job Cancel
on the control panel.
The LED indications shown in the table below are used in the illustrations in this chapter.
LED is off.
LED is on.
or
or
LED is blinking.
or
or
Note
When the power switch is off or the printer is in sleep mode, all the LEDs are off.
4-1
Control Panel
LED
Printer status
Sleep mode
The power switch is off or the printer is in sleep mode. Pressing Go wakes up the
printer from sleep mode to ready mode.
Ready to print
The printer is ready to print.
Warming up
The printer is warming up.
Cooling down
The printer is cooling down. Wait for a few seconds until inside of the printer has
cooled down.
Receiving data
The printer is either receiving data from the computer, processing data in memory or
printing the data.
4-2
Control Panel
LED
Printer status
Data remaining in memory
There is remaining print data in the printer memory. If the yellow Status LED is on
for a long time and nothing has printed, press Go to print the remaining data in
memory.
Toner low
Indicates that the toner cartridge is nearly empty. Buy a new toner cartridge and have
it ready for when Toner life end is indicated.
The Toner LED will turn on for 2 seconds and off for 3 seconds.
Toner life end
Replace the toner cartridge with a new one. See Replacing the toner cartridge on
page 6-3.
Cartridge position error
The drum unit assembly is not installed correctly. Take the drum unit out of the
machine and put it back in.
Drum life end soon
The drum unit is near the end of its life. We recommend that you get a new drum unit
to replace the current one. See Replacing the drum unit on page 6-8.
The Drum LED will turn on for 2 seconds and off for 3 seconds.
4-3
Control Panel
LED
Printer status
No paper
Put paper in the tray. Then press Go. See Printing on plain paper, bond paper and
transparencies on page 2-5 or Printing on thick paper, labels and envelopes on page
2-11.
Paper jam
Clear the paper jam. See Paper jams and how to clear them on page 7-6. If the
printer does not start printing, press Go.
Incorrect Paper size for Duplex (For HL-5250DN)
Prees Go or Job Cancel. Set the correct paper that you want to use, or load the
same size paper that you selected in the current driver setting. The paper size you
can use for automatic duplex printing is A4, Letter or Legal.
Duplex disabled
Close the back cover of the printer and put the duplex tray back in.
Front cover is open
Close the front cover of the printer.
Fuser cover is open
Close the fuser cover which can be found behind the back cover of the printer.
Dust on drum
The corona wire needs to be cleaned. See Cleaning the corona wire on page 6-17.
Too many trays
Maximum number of optional trays is two. Remove additional trays.
Buffer error
Check the cable connection between the PC and printer.
Memory full
The printer memory is full and the printer cannot print full pages of a document.
See Solving print problems on page 7-18.
Print overrun
A print overrun occurred and the printer cannot print full pages of a document.
See Solving print problems on page 7-18.
Download full
The download buffer of the printer is full. Add more memory to the printer. See
Installing extra memory on page 5-3.
Font full
The font memory area is full. Delete fonts or add more memory to the printer. See
Installing extra memory on page 5-3.
4-4
Control Panel
Service call indications
If there is an error that cannot be cleared by the user, the printer will show that a service call is needed by
lighting up all the LEDs as shown below.
If you see the service call indication shown above, turn off the power switch, wait a few seconds, and then
turn it back on and try to print again.
If you cannot clear the error and see the same service call indication after turning the printer back on, call
your dealer or a Brother authorized service representative.
When you press Go and Job Cancel buttons together, the LEDs will light up as shown in the table below to
identify the error.
LED indications while pressing Go and Job Cancel
LEDs
Main PCB
failure
Fuser unit
failure 1
Laser unit
failure
Main motor
failure
High voltage
failure
DIMM error 2
Toner
Drum
Paper
Status
1
If this error occurs, turn off the printer power switch, wait a few seconds, and then turn it on again. Leave the printer for 10 minutes with the power
on. If the error occurs again, call your dealer or Brother authorized service representative.
2
If this error occurs, ensure that the DIMM is installed correctly. See Installing extra memory on page 5-3.
4-5
Control Panel
For example, the LED indication below shows a fuser unit failure.
Make a note of the indication and report the error status to your dealer or a Brother authorized service
representative by referring to the above table.
Note
Make sure that the front cover is completely closed before you report a service call.
4-6
Control Panel
Control panel button
The control panel buttons have the following functions:
„ Cancel printing
If you press Job Cancel while printing, the printer will immediately stop printing and will then eject the
paper.
„ Wake-up
If the printer is in sleep mode, press Go or Job Cancel to wake the printer up and go to the Ready state.
„ Error recovery
If there is an error, the printer will recover automatically from some errors. If an error is not automatically
cleared, press Go to clear the error, and then continue to use the printer.
„ Form feed
If the yellow Status LED is on for a long time, press Go. The printer will print any remaining data in the
printer memory.
„ Reprint
To reprint the last document, press Go and hold it down for about 4 seconds until all the LEDs light up in
order (Toner, Drum, Paper, Status), and then release Go. Within 2 seconds press Go the number of
times you want to reprint. If you don’t press Go within 2 seconds, a single copy will be printed.
4-7
Control Panel
Print a test page
You can use the Go button or the printer driver to print a test page.
Using control panel button
a
b
c
Turn off the printer.
d
Press Go again. The printer will print a test page.
Make sure that the front cover is closed and the power cord is plugged in.
Hold down Go as you turn on the power switch. First all the LEDs will light up, and then the Status LED
will turn off. Release Go. Make sure that all the LEDs have turned off.
Using the printer driver
If you are using Brother’s Windows® printer driver, click the Print Test Page button in the General tab of the
Windows® printer driver.
4-8
Control Panel
Print a Printer Settings page
You can print the current settings using the control panel button or printer driver.
Using the control panel button
a
b
c
Make sure that the front cover is closed and the power cord is plugged in.
Turn on the printer and wait until the printer is in the ready state.
Press Go three times within 2 seconds. The printer will print the current printer settings page.
Using the printer driver
If you are using Brother’s Windows® printer driver, you can print the current printer settings page by clicking
the Print Settings button in the Support tab.
4-9
Control Panel
Print Fonts
You can print a list of the internal fonts using the control panel button or printer driver.
Using the control panel button
a
b
c
Turn off the printer.
d
Press Go twice. The printer will print a list of the internal fonts.
Make sure that the front cover is closed and the power cord is plugged in.
Hold down Go as you turn on the power switch. First all the LEDs will light up, and then the Status LED
will turn off. Release Go. Make sure that all the LEDs have turned off.
Using the printer driver
If you are using Brother’s Windows® printer driver, you can print a list of the internal fonts by clicking the
Print Fonts button in the Support tab.
4 - 10
Control Panel
Network default setting (For HL-5250DN)
If you want to reset the print server back to its default settings (resetting all information such as the password
and IP address information), follow these steps:
a
b
c
Turn off the printer.
d
Press Go six times. Make sure that all the LEDs light up to indicate the print server has been reset to its
default settings.
Make sure that the front cover is closed and the power cord is plugged in.
Hold down Go as you turn on the power switch. First all the LEDs will light up, and then the Status LED
will turn off. Release Go. Make sure that all the LEDs have turned off.
Network default setting with APIPA protocol disabled (For HL-5250DN)
If you want to reset the print server back to its default settings with APIPA protocol disabled, follow these
steps:
a
b
c
Turn off the printer.
d
Press Go seven times. Make sure that all the LEDs light up to indicate the print server has been reset to
its default settings.
Make sure that the front cover is closed and the power cord is plugged in.
Hold down Go as you turn on the power switch. First all the LEDs will light up, and then the Status LED
will turn off. Release Go. Make sure that all the LEDs have turned off.
Note
• For more information on APIPA, see the Network User’s Guide.
• You can also disable the APIPA protocol using a web browser, BRAdmin Professional, BRAdmin Light or
Web BRAdmin.
4 - 11
5
Options
This printer has the following optional accessories. You can increase the capabilities of the printer with these
items.
Lower tray unit
DIMM memory
LT-5300
See Lower tray unit (LT-5300) on this
page.
Print server
(For HL-5240)
NC-2100p
See DIMM on page 5-2. And See
Installing extra memory on page 5-3.
See Print server (NC-2100p) (For
HL-5240) on page 5-5.
Lower tray unit (LT-5300)
Two optional lower trays (Tray 2 or Tray 3) can be installed, and each lower tray can hold up to 250 sheets
of 80 g/m2 (21 lb) paper.
When both optional trays are installed, the printer can hold up to 800 sheets of plain paper. If you want to buy
an optional lower tray unit, call the dealer you bought the printer from.
For setup, see the User's Guide that we have supplied with the lower tray unit.
5-1
Options
DIMM
For HL-5240
The HL-5240 printer has 16 MB of standard memory and one slot for optional memory expansion. You can
expand the memory up to 528 MB by installing dual in-line memory modules (DIMMs).
For HL-5250DN
The HL-5250DN printer has 32 MB of standard memory and one slot for optional memory expansion. You
can expand the memory up to 544 MB by installing dual in-line memory modules (DIMMs).
DIMM types
You can install the following DIMMs:
„ 128 MB Buffalo Technology VN133-D128 / VN133-X128
„ 256 MB Buffalo Technology VN133-D256
„ 512 MB Buffalo Technology VN133-D512
„ 64 MB TechWorks 12165-0004
„ 128 MB TechWorks 12462-0001
„ 256 MB TechWorks 12485-0001
„ 512 MB TechWorks 12475-0001
Note
• For more information, visit the Buffalo Techonology site at http://www.buffalotech.com.
• For more information, visit the Techworks web site at http://www.techworks.com.
In general, the DIMM must have the following specifications:
Type: 144 pin and 64 bit output
CAS latency: 2
Clock frequency: 100 MHz or more
Capacity: 64, 128, 256 or 512 MB
Height: 31.75 mm (1.25 in.)
Dram Type: SDRAM 2 Bank
SDRAM can be used.
Note
• There might be some DIMMs that will not work with the printer.
• For more information, call the dealer you bought the printer from or Brother Customer Service.
5-2
Options
Installing extra memory
a
Turn off the printer power switch, and then unplug the printer. Disconnect the interface cable from the
printer.
Note
Be sure to turn off the printer power switch before you install or remove the DIMM.
b
Remove the DIMM cover.
c
Unpack the DIMM and hold it by its edges.
CAUTION
To prevent damage to the printer from static electricity, DO NOT touch the memory chips or the board
surface.
d
Hold the DIMM by the edges and align the notches in the DIMM with the protrusions in the slot.
Insert the DIMM diagonally (1), then tilt it toward the interface board until it click into place (2).
1
2
5-3
Options
e
Put the DIMM cover back on.
f
Reconnect the interface cable to your printer. Plug the printer back in, and then turn on the power switch.
Note
To make sure that you have installed the DIMM properly, you can print the printer settings page that shows
the current memory size. See Print a Printer Settings page on page 4-9.
5-4
Options
Print server (NC-2100p) (For HL-5240)
An optional network print server (NC-2100p) allows you to connect to your network through the parallel
interface.
Network interface
10/100BASE-TX Ethernet
Printer interface
Parallel
Support protocol
TCP/IP, NetBEUI
Management features
Embedded web server support
SNMP / MIB support
TELNET remote console
BRAdmin Professional compatible
Flash memory for easy updating of firmware
Note
HL-5250DN already has a built-in 10/100BASE-TX Ethernet Print Server.
5-5
6
Routine Maintenance
You will need to replace certain parts and clean the printer regularly.
WARNING
When you replace certain parts or clean the inside of the printer, remember the following:
• If your clothes are smeared with toner, wipe off the toner with a dry cloth and immediately wash the
clothes in cold water to avoid stains.
• Be careful not to inhale toner.
• After you have just used the printer, some internal parts of the printer will be extremely hot. When you
open the front cover or back cover of the printer, DO NOT touch the shaded parts shown in the
illustration.
Replacing the consumable items
You will need to replace the consumable items regularly.
Note
These instructions are also included in Improving the print quality on page 7-13.
Consumables
Toner Cartridge
Drum Unit
See Toner cartridge on page 6-2.
See Drum unit on page 6-8.
6-1
Routine Maintenance
Toner cartridge
A new toner cartridge can print approximately 3,500 (standard cartridge) or approximately 7,000 (high yield
cartridge) A4 or Letter size single-sided pages at 5% coverage.
Note
• The amount of toner used varies according to what is printed on the page and the print density setting.
• If you change the print density setting for lighter or darker printing, the amount of toner used will change.
• Wait to unpack the toner cartridge until immediately before you put it into the printer.
Toner Low message
The Toner LED will turn on for 2 seconds and off for 3 seconds.
If the LED shows this message, the printer has nearly run out of toner. Buy a new toner cartridge and have it
ready before you get a Toner Life End message. To replace the toner cartridge, see Replacing the toner
cartridge on page 6-3.
Note
The Toner LED will blink continuously if the toner cartridge is nearly empty.
Toner Life End message
The printer will stop printing until you replace the toner cartridge with a new one.
6-2
Routine Maintenance
Replacing the toner cartridge
Note
• To ensure high quality printing, we recommend that you use only genuine Brother toner cartridges. When
you want to buy toner cartridges, call the dealer you bought the printer from or Brother Customer Service.
• We recommend that you clean the printer when you replace the toner cartridge. See Cleaning on page 613.
a
Press the front cover release button and then open the front cover.
b
Take out the drum unit and toner cartridge assembly.
CAUTION
We recommend that you put the drum unit and toner cartridge assembly on a piece of disposable paper or
cloth in case you accidentally spill or scatter toner.
To prevent damage to the printer from static electricity, DO NOT touch the electrodes shown in the
illustration.
6-3
Routine Maintenance
c
Push down the blue lock lever and take the toner cartridge out of the drum unit.
CAUTION
DO NOT put a toner cartridge into a fire. It could explode, resulting in injuries.
Handle the toner cartridge carefully. If toner scatters on your hands or clothes, wipe or wash it off with cold
water at once.
To avoid print quality problems, DO NOT touch the shaded parts shown in the illustrations.
Note
• Be sure to seal up the toner cartridge tightly in a bag so that toner powder does not spill out of the cartridge.
• Discard the used toner cartridge according to local regulations, keeping it separate from domestic waste.
If you have questions, call your local waste disposal office.
d
Unpack the new toner cartridge. Hold the cartridge level with both hands and gently rock it from side to
side five or six times to spread the toner evenly inside the cartridge.
6-4
Routine Maintenance
CAUTION
Wait to unpack the toner cartridge until immediately before you put it in the printer. If toner cartridges are
left unpacked for a long time the toner life will be shortened.
If an unpacked drum unit is put in direct sunlight or room light, the unit may be damaged.
Put the toner cartridge in the drum unit immediately after you have removed the protective cover. To prevent
any degradation to the print quality, DO NOT touch the shaded parts shown in the illustrations.
CAUTION
For USA and Canada
Brother strongly recommends that you do not refill the toner cartridge provided with your printer. We also
strongly recommend that you continue to use only genuine Brother brand replacement toner cartridges. Use
or attempted use of potentially incompatible toner and/or cartridges in the Brother machine may cause
damage to the machine and/or may result in unsatisfactory print quality. Our warranty coverage does not
apply to any problem that is caused by the use of unauthorized third party toner and/or cartridges. To protect
your investment and obtain premium performance from the Brother machine, we strongly recommend the
use of genuine Brother supplies.
CAUTION
For UK and countries
Brother machines are designed to work with toner of a particular specification and will work to a level of
optimum performance when used with genuine Brother branded toner cartridges. Brother cannot guarantee
this optimum performance if toner or toner cartridges of other specifications are used. Brother does not
therefore recommend the use of cartridges other than genuine Brother branded cartridges with this
machine.
If damage is caused to the drum unit or other part of this machine as a result of using other manufacturer’s
products with this machine, any repairs required as a result may not be covered by the warranty.
6-5
Routine Maintenance
e
Pull off the protective cover.
f
Put the new toner cartridge firmly into the drum unit until you hear it lock into place. If you put it in
properly, the lock lever will lift automatically.
CAUTION
Make sure that you put in the toner cartridge properly or it may separate from the drum unit.
g
Clean the primary corona wire inside the drum unit by gently sliding the blue tab from right to left and left
to right several times.
1
CAUTION
Be sure to return the tab to the home position (a) (1). If you do not, printed pages may have a vertical stripe.
6-6
Routine Maintenance
h
Put the drum unit and toner cartridge assembly back in the printer. Close the front cover.
6-7
Routine Maintenance
Drum unit
A new drum unit can print approximately 25,000 A4 or Letter size single-sided pages at 5% coverage.
Note
• There are many factors that determine the actual drum life, such as the temperature, humidity, type of
paper, type of toner used, number of pages per print job and so on. Under ideal conditions, the average
drum life is estimated at approximately 25,000 pages. The actual number of pages that your drum will print
may be significantly less than this estimate. Because we have no control over the many factors that
determine the actual drum life, we cannot guarantee a minimum number of pages that will be printed by
your drum.
• For best performance, use only genuine Brother toner. The printer should be used only in a clean, dustfree environment with adequate ventilation.
• Printing with a third-party drum unit may reduce not only the print quality but also the quality and life of the
printer itself. Warranty coverage does not apply to problems caused by the use of a third-party drum unit.
Change Drum message
If the LED shows the message below, it means the drum unit is near the end of its life. We recommend that
you replace the drum unit with a new one before there is a noticeable deterioration in the print quality.
Replacing the drum unit
CAUTION
While removing the drum unit, handle it carefully because it may contain toner.
Every time you replace the drum unit, clean the inside of the printer. See Cleaning on page 6-13.
6-8
Routine Maintenance
When you replace the drum unit with a new one, you need to reset the drum counter by completing the
following steps:
a
Make sure that the printer is turned on and the Drum LED is blinking. Press the front cover release button
and then open the front cover.
b
Press and hold down Go for about 4 seconds until all the LEDs light up. Once all four LEDs are lit, release
Go.
Improper Setup
Do not reset the drum counter when you only replace the toner cartridge.
c
Take out the drum unit and toner cartridge assembly.
6-9
Routine Maintenance
CAUTION
We recommend that you put the drum unit and toner cartridge assembly on a piece of disposable paper or
cloth in case you accidentally spill or scatter toner.
To prevent damage to the printer from static electricity, DO NOT touch the electrodes shown in the
illustration.
d
Push down the blue lock lever and take the toner cartridge out of the drum unit.
CAUTION
Handle the toner cartridge carefully. If toner scatters on your hands or clothes, wipe or wash it off with cold
water at once.
To avoid print quality problems, DO NOT touch the shaded parts shown in the illustrations.
Note
• Be sure to seal up the drum unit tightly in a bag so that toner powder does not spill out of the unit.
• Discard the used drum unit according to local regulations, keeping it separate from domestic waste. If you
have questions, call your local waste disposal office.
6 - 10
Routine Maintenance
e
Unpack the new drum unit.
CAUTION
Wait to unpack a drum unit until immediately before you put it in the printer. Exposure to direct sunlight or
room light may damage the drum unit.
f
Put the toner cartridge firmly into the new drum unit until you hear it lock into place. If you put the cartridge
in properly, the blue lock lever will lift automatically.
CAUTION
Make sure that you put in the toner cartridge properly, or it may separate from the drum unit.
g
Put the drum unit and toner cartridge assembly back in the printer.
h
i
Close the front cover.
Make sure that the Drum LED is now off.
6 - 11
Routine Maintenance
Replacing periodic maintenance parts
You need to replace the periodic maintenance parts regularly to maintain print quality. You should replace
the parts listed below after printing the following number of pages.
1
Item
Approximate Life
To Buy Replacement
Separator pad holder assembly
100,000 pages 1
Call Brother Customer Service
Pick up roller assembly
100,000 pages 1
Call Brother Customer Service
Laser unit
100,000 pages 1
Call Brother Customer Service
Fuser unit
100,000 pages 1
Call Brother Customer Service
At 5% print coverage (A4 or Letter size). The actual number of printed pages will vary depending on the print jobs and paper you use.
6 - 12
Routine Maintenance
Cleaning
Clean the outside and inside of the printer regularly with a dry, lint-free cloth. When you replace the toner
cartridge or the drum unit, make sure that you clean the inside of the printer. If printed pages are stained with
toner, clean the inside of the printer with a dry, lint-free cloth.
Cleaning the outside of the printer
CAUTION
Use neutral detergents. Cleaning with volatile liquids such as thinner or benzine will damage the surface of
the printer.
DO NOT use cleaning materials that contain ammonia.
a
Turn off the printer power switch and then unplug the printer.
b
Pull the paper tray completely out of the printer.
6 - 13
Routine Maintenance
c
Wipe the outside of the printer with a dry, lint-free cloth to remove dust.
d
e
Remove anything that is stuck inside the paper tray.
f
g
Put the paper tray back in the printer.
Wipe the inside of the paper tray with a dry, lint-free cloth to remove dust.
Plug the printer back in, and then turn on the power switch.
Cleaning the inside of the printer
a
Turn off the printer power switch and then unplug the printer.
6 - 14
Routine Maintenance
b
Press the front cover release button and then open the front cover.
c
Take out the drum unit and toner cartridge assembly.
HOT SURFACE
After you have just used the printer, some internal parts of the printer will be extremely hot. Wait for the
printer to cool down before you touch the internal parts of the printer.
CAUTION
We recommend that you put the drum unit and toner cartridge assembly on a piece of disposable paper or
cloth in case you accidentally spill or scatter toner.
Handle the toner cartridge carefully. If toner scatters on your hands or clothes, wipe or wash it off with cold
water at once.
6 - 15
Routine Maintenance
To prevent damage to the printer from static electricity, DO NOT touch the electrodes shown in the
illustration.
d
Wipe the scanner window with a dry, lint-free cloth.
e
f
g
Put the drum unit and toner cartridge assembly back in the printer.
Close the front cover.
Plug the printer back in, and then turn on the power switch.
6 - 16
Routine Maintenance
Cleaning the corona wire
If you have print quality problems, clean the corona wire as follows:
a
Press the front cover release button and then open the front cover.
b
Take out the drum unit and toner cartridge assembly.
CAUTION
We recommend that you put the drum unit and toner cartridge assembly on a piece of disposable paper or
cloth in case you accidentally spill or scatter toner.
To prevent damage to the printer from static electricity, DO NOT touch the electrodes shown in the
illustration.
6 - 17
Routine Maintenance
c
Clean the primary corona wire inside the drum unit by gently sliding the blue tab from right to left and left
to right several times.
1
CAUTION
Be sure to return the tab to the home position (a) (1). If you do not, printed pages may have a vertical stripe.
d
Put the drum unit and toner cartridge assembly back in the printer. Close the front cover.
6 - 18
7
Troubleshooting
You can correct most problems by yourself. If you need additional help, the Brother Solutions Center offers
the latest FAQs and troubleshooting tips. Visit us at http://solutions.brother.com.
Identifying your problem
First, check the following:
„ The AC power cord is connected properly and the printer is turned on.
„ All of the protective parts have been removed.
„ The toner cartridge and drum unit are installed properly.
„ The front cover is fully closed.
„ Paper is inserted properly in the paper tray.
„ The interface cable is securely connected to the printer and the computer.
„ The correct driver for the printer has been chosen and is installed.
„ The PC is set up to connect to the correct printer port.
Printer does not print:
If you did not solve your problem with the above checks, identify your problem and then go to the page
suggested below.
„ Printer LED is blinking
See LEDs (Light Emitting Diodes) on page 4-1.
„ Status Monitor Error Message appears
See Error messages in the Status Monitor on page 7-2.
„ Printer printed an Error Message
See Error message printout on page 7-4.
„ Paper handling
See Paper handling on page 7-5 and Paper jams and how to clear them on page 7-6.
„ Other problems
See Other problems on page 7-19.
Pages are printed, but there are problems with:
„ Print quality
See Improving the print quality on page 7-13.
„ Printout is incorrect
See Solving print problems on page 7-18.
7-1
Troubleshooting
Error messages in the Status Monitor
The Status Monitor will report problems with the printer. Take the proper action by referring to the following
table.
The default setting for the Status Monitor is off. If you want to turn the status monitor on, you can change the
setting of the Status Monitor in Device Options from the Advanced tab. See Device Options on page 3-6.
Error message
Action
Toner Low
„ Buy a new toner cartridge and have it ready for when the Toner Life End status
is indicated.
Toner Life End
„ See Replacing the toner cartridge on page 6-3.
Cartridge Position Error
„ Put the drum unit assembly back in.
Drum Life End Soon
„ The drum unit is near the end of its life. Buy a new drum unit to replace the current
one. See Replacing the drum unit on page 6-8.
No Paper
„ The paper tray may be out of paper or not properly installed. If it is empty, put a
new stack of paper in the paper tray and then press Go.
No Paper for Manual Feed
No Paper in the
Multi Purpose Tray
No Paper MP or Size
Mismatch
No Paper in Tray 1/2/3
No Paper in Tray 1/2/3 or Size
Mismatch
Jam MP Tray
Jam Tray 1/2/3
„ If there is paper in the paper tray, make sure it is straight. If the paper is curled,
straighten it before printing. Sometimes it is helpful to remove the paper, turn the
stack over and put it back in the paper tray.
„ Cut the amount of paper in the paper tray, and then try again.
„ Make sure you use paper that meets Brother’s recommended paper
specifications. See About paper on page 2-1.
„ Load the same size paper that you selected in the current driver setting.
„ Clear the jammed paper from the indicated area. See Paper jams and how to
clear them on page 7-6.
Jam Inside
Jam Rear
Jam Duplex
Incorrect Paper Size for Auto
DX
„ Press Go or Job Cancel. Set the correct paper that you want to use, or load the
same size paper that you selected in the current driver setting. The paper size
you can use for automatic duplex printing is A4, Letter or Legal.
Duplex Disabled
„ Close the back cover of the printer and put the duplex tray back in.
Front Cover is Open
„ Close the front cover of the printer.
Fuser Cover is Open
„ Close the fuser cover located behind the back cover of the printer.
7-2
Troubleshooting
Error message
Action
Dust On Drum
„ See Cleaning the corona wire on page 6-17.
Memory Full
„ Press Go to print the remaining data in the printer memory. Cancel the print job
if you want to delete the remaining data in the printer memory. See Control panel
button on page 4-7.
„ Reduce the complexity of your document or cut the print resolution.
„ Add more memory. See Installing extra memory on page 5-3.
Print Overrun
„ Press Go to print the remaining data in the printer memory. Cancel the print job
if you want to delete the remaining data in the printer memory. See Control panel
button on page 4-7.
„ If this does not clear the error, reduce the complexity of your document or cut the
print resolution.
„ Add more memory. See Installing extra memory on page 5-3.
„ Set page protection to AUTO by using the supplied Windows ® driver or Remote
Printer Console program.
„ Change the following settings in the supplied Windows® driver and try again. The
best combination of these settings will vary depending on your document:
• Graphics mode
• TrueType mode
• Use Printer TrueType® Fonts
Service Call Error
„ Check the LED indication to identify the error. See Service call indications on
page 4-5.
7-3
Troubleshooting
Error message printout
The printer can also report problems by printing an error message. Use the table below to identify and clear
the error message.
Error message
MEMORY FULL
Action
„ Press Go to print the remaining data in the printer memory. Cancel the print job
if you want to delete the remaining data in the printer memory. See Control panel
button on page 4-7.
„ Reduce the complexity of your document or cut the print resolution.
„ Add more memory. See Installing extra memory on page 5-3
PRINT OVERRUN
„ Press Go to print the remaining data in the printer memory. Cancel the print job
if you want to delete the remaining data in the printer memory. See Control panel
button on page 4-7.
„ If this does not clear the error, reduce the complexity of your document or cut the
print resolution.
„ Add more memory. See Installing extra memory on page 5-3.
„ Set page protection to AUTO by using the supplied Windows ® driver or Remote
Printer Console program.
„ Change the following settings in the supplied Windows® driver and try again. The
best combination of these settings will vary depending on your document:
• Graphics mode
• TrueType mode
• Use Printer TrueType® Fonts
RESOLUTION REDUCED TO
ENABLE PRINTING
„ Reduce the complexity of your document before you print to prevent automatic
reduction in the resolution.
(The printer has printed the
document at a reduced
resolution)
7-4
Troubleshooting
Paper handling
First, make sure that you are using paper that meets Brother recommended paper specifications. See About
paper on page 2-1.
Problem
The printer does not feed
paper.
Recommendation
„ If there is paper in the paper tray, make sure it is straight. If the paper is curled,
straighten it before printing. Sometimes it is helpful to remove the paper. Turn the
stack over and put it back in the paper tray.
„ Cut the amount of paper in the paper tray, and then try again.
„ Make sure that manual feed mode is not chosen in the printer driver.
The printer does not feed paper
from the MP tray.
„ Fan the paper well and put it back in firmly.
The printer does not feed
envelopes.
„ The printer can feed envelopes from the multi-purpose tray. You must set up your
application to print on the size of envelopes you are using. This is usually done in
the page setup or document setup menu of your software. See your application
manual.
A paper jam has occurred.
„ Clear the jammed paper. See Paper jams and how to clear them on page 7-6.
The printer does not print.
„ Make sure that the cable is connected to the printer.
„ Make sure that you have chosen the MP Tray in the Paper Source of the printer
driver.
„ Make sure that you have chosen the proper printer driver.
When printing on normal paper,
it creases.
„ Change the printer driver setting in Media Type to a thin setting.
When printing on Legal size
paper or longer sized paper,
the paper slides off the top
output tray.
„ Pull out and lift up the output tray support flap.
7-5
Troubleshooting
Paper jams and how to clear them
If a paper jam occurs, the printer will flash the Paper LED as shown below.
HOT SURFACE
After you have just used the printer, some internal parts of the printer will be extremely hot. When you open
the front cover or back cover of the printer, DO NOT touch the shaded parts shown in the illustrations.
Clear the jammed paper as follows.
If the jammed paper is removed completely by following the steps below, you can install the paper tray first,
and then close the front cover. The printer will resume printing automatically.
If the printer does not start printing automatically, press Go. If the printer still does not start printing, check
that all the remaining jammed paper has been removed from the printer. Then try printing again.
Note
Always remove all paper from the paper tray and straighten the stack when you add new paper. This helps
prevent multiple sheets of paper from feeding through the printer at one time and prevents paper jams.
7-6
Troubleshooting
a
Press the cover release button and then open the front cover.
b
Slowly take out the drum unit and toner cartridge assembly. The jammed paper will be pulled out with
the drum unit and toner cartridge assembly.
CAUTION
To prevent damage to the printer caused by static electricity, DO NOT touch the electrodes shown in the
illustration.
7-7
Troubleshooting
c
Pull the paper tray completely out of the printer.
d
e
Close the front cover.
f
Open the front cover again.
Pull the jammed paper up and out of the printer.
7-8
Troubleshooting
g
Open the back cover.
h
Pull the tabs at the left and right hand sides toward you to open the fuser cover (1).
1
i
Using both hands, gently pull the jammed paper out of the fuser unit.
7-9
Troubleshooting
HOT SURFACE
After you have just used the printer, some internal parts of the printer will be extremely hot. Wait for the
printer to cool down before you touch the internal parts of the printer.
j
k
Close the back cover.
l
Pull the the jammed paper out of the printer or the duplex tray. Put the duplex tray back in the printer.
Pull the duplex tray completely out of the printer.
7 - 10
Troubleshooting
m
Push down the blue lock lever and take the toner cartridge out of the drum unit. Clear the jammed paper
if there is any inside the drum unit.
CAUTION
Handle the toner cartridge carefully. If toner scatters on your hands or clothes, wipe or wash it off with cold
water at once.
To avoid print quality problems, DO NOT touch the shaded parts shown in the illustrations.
n
Put the toner cartridge back into the drum unit until you hear it lock into place. If you put the cartridge in
properly, the blue lock lever will lift automatically.
7 - 11
Troubleshooting
o
Put the drum unit and toner cartridge assembly back in the printer.
p
q
r
Put the paper tray firmly back in the printer.
Close the front cover.
Make sure that the Paper LED is now off and the printer is ready.
7 - 12
Troubleshooting
Improving the print quality
If you have a print quality problem, print a test page first (see Print a test page on page 4-8). If the printout
looks good, the problem is probably not the printer. Check the interface cable or try the printer on another PC.
This section gives information on the following topics.
Examples of poor print
quality
ABCDEFGH
CDEF
abcdefghijk
defg
ABCD
abcde
01234
Faint
Recommendation
„ Check the printer’s environment. Conditions such as humidity, high
temperatures, and so on, may cause this print fault. See Positioning the printer
on page 1-4.
„ If the whole page is too light, Toner Save Mode may be on. Turn off Toner Save
Mode in the printer Properties tab of the driver.
„ Put in a new toner cartridge. See Replacing the toner cartridge on page 6-3.
„ Put in a new drum unit. See Replacing the drum unit on page 6-8.
„ You may clear the problem by wiping the scanner window with a soft cloth. See
Cleaning the inside of the printer on page 6-14.
„ Make sure that you use paper that meets our specifications. See About paper on
page 2-1.
ABCDEFGH
abcdefghijk
ABCD
abcde
01234
„ Check the printer’s environment. Conditions such as high temperatures and high
humidity can increase the amount of background shading. See Positioning the
printer on page 1-4.
„ Put in a new toner cartridge. See Replacing the toner cartridge on page 6-3.
„ Put in a new drum unit. See Replacing the drum unit on page 6-8.
Gray background
„ Make sure that you use paper that meets our specifications. Rough-surfaced
paper or thick print media may cause this problem. See About paper on page 2-1.
„ Make sure that the media type setting in the driver matches the type of paper you
are using. See About paper on page 2-1.
„ Put in a new drum unit. See Replacing the drum unit on page 6-8.
„ The fuser unit may be contaminated. Call Brother Customer Service.
Ghost
„ Make sure that you use paper that meets our specifications. Rough-surfaced
paper may cause the problem. See About paper on page 2-1.
ABCDEFGH
abcdefghijk
ABCD
abcde
01234
„ The drum unit may be damaged. Put in a new drum unit. See Replacing the drum
unit on page 6-8.
„ The fuser unit may be contaminated. Call Brother Customer Service.
Toner specks
7 - 13
Troubleshooting
Examples of poor print
quality
Recommendation
„ Make sure that you use paper that meets our specifications. See About paper on
page 2-1.
„ Choose Thick paper mode in the printer driver, or use thinner paper than what
you are now using.
„ Check the printer’s environment. Conditions such as high humidity can cause
hollow print. See Positioning the printer on page 1-4.
Hollow print
„ Clean the primary corona wire inside the drum unit by sliding the blue tab. Be sure
to return the blue tab to the home position (a). See Cleaning the corona wire on
page 6-17.
„ The drum unit may be damaged. Put in a new drum unit. See Replacing the drum
unit on page 6-8.
„ The fuser unit may be contaminated. Call Brother Customer Service.
All black
„ Make sure that you use paper that meets our specifications. A rough surfaced
paper or thick print media can cause problems.
ABCDEFGH
abcdefghijk
„ Make sure that you choose the proper media type in the printer driver.
ABCD
abcde
01234
„ The problem may disappear by itself. Print multiple pages to clear this problem,
especially if the printer has not been used for a long time.
„ The drum unit may be damaged. Put in a new drum unit. See Replacing the toner
cartridge on page 6-3.
White lines across the page
„ Clean the inside of the printer and the primary corona wire in the drum unit. See
Cleaning on page 6-13.
ABCDEFGH
abcdefghijk
ABCD
abcde
01234
„ The drum unit may be damaged. Put in a new drum unit. See Replacing the drum
unit on page 6-8.
Lines across the page
„ Make sure that a torn piece of paper is not inside the printer covering the scanner
window.
ABCDEFGH
abcdefghijk
ABCD
abcde
01234
White lines down the page
„ Wipe the scanner window with a soft cloth. See Cleaning the inside of the printer
on page 6-14.
„ The toner cartridge may be damaged. Put in a new toner cartridge. See
Replacing the toner cartridge on page 6-3.
„ The drum unit may be damaged. Put in a new drum unit. See Replacing the drum
unit on page 6-8.
7 - 14
Troubleshooting
Examples of poor print
quality
Recommendation
„ If the problem is not solved after printing a few pages, the drum unit may have
glue from the label stuck on the OPC drum surface.
94 mm
(3.7 in.)
94 mm
(3.7 in.)
Clean the drum unit as follows:
a
Put the print sample in front of the drum unit, and find the exact position of
the poor print.
b
Turn the drum unit gear by hand while looking at the surface of the OPC
drum (1).
White Spots on black text
and graphics at 94 mm
(3.7 in.) intervals
94 mm
(3.7 in.)
94 mm
(3.7 in.)
1
Black Spots at 94 mm
(3.7 in.) intervals
c
When you have found the mark on the drum that matches the print sample,
wipe the surface of the OPC drum with a cotton swab until the dust or paper
powder on the surface comes off.
CAUTION
DO NOT clean the surface of the photosensitive drum with a sharp object.
„ The drum unit may be damaged. Put in a new drum unit. See Replacing the drum
unit on page 6-8.
7 - 15
Troubleshooting
Examples of poor print
quality
Recommendation
„ The drum unit may be damaged. Put in a new drum unit. See Replacing the drum
unit on page 6-8.
ABCDEFGH
abcdefghijk
„ Make sure that you use paper that meets our specifications. See About paper on
page 2-1.
ABCD
abcde
01234
„ If you use label sheets for laser printers, the glue from the sheets may sometimes
stick to the OPC drum surface. Clean the drum unit. See on Clean the drum unit
as follows: on page 7-15.
Black toner marks across the
page
„ Do not use paper that has clips or staples because they will scratch the surface
of the drum.
„ If the unpacked drum unit is in direct sunlight or room light, the unit may be
damaged.
„ Clean the primary corona wire inside the drum unit by sliding the blue tab. See
Cleaning the corona wire on page 6-17.
ABCDEFGH
abcdefghijk
„ Make sure the primary corona wire cleaner is at the home position (a).
ABCD
abcde
01234
„ The drum unit may be damaged. Put in a new drum unit. See Replacing the drum
unit on page 6-8.
Black lines down the page
„ The fuser unit may be smudged. Call your dealer or Brother Customer Service.
„ The toner cartridge may be damaged. Put in a new toner cartridge. See
Replacing the toner cartridge on page 6-3.
Printed pages have toner stains
down the page.
FGH
ABCDE ijk
h
fg
e
d
abc
ABCD
abcde
01234
Page skewed
„ Make sure that the paper or other print media is loaded properly in the paper tray
and that the guides are not too tight or too loose against the paper stack.
„ Set the paper guides correctly. See Printing on plain paper, bond paper or
transparencies from Tray 1, 2 or 3 on page 2-5.
„ If you are using the multi-puroise tray, see Printing on plain paper, bond paper or
transparencies from the MP tray on page 2-8.
„ The paper tray may be too full. See Printing on plain paper, bond paper or
transparencies from Tray 1, 2 or 3 on page 2-5.
„ Check the paper type and quality. See About paper on page 2-1.
„ Check the paper type and quality. High temperatures and high humidity will cause
paper to curl. See About paper on page 2-1.
„ If you do not use the printer often, the paper may have been in the paper tray too
long. Turn over the stack of paper in the paper tray. Also, fan the paper stack and
then rotate the paper 180° in the paper tray.
Curled or wavy
7 - 16
Troubleshooting
Examples of poor print
quality
Recommendation
„ Make sure that the paper is loaded properly. See Printing on plain paper, bond
paper or transparencies from Tray 1, 2 or 3 on page 2-5.
B DEFGH
abc efghijk
„ Check the paper type and quality. See About paper on page 2-1.
A CD
bcde
1 34
„ Turn over the stack of paper in the tray or try rotating the paper 180° in the input
tray.
Wrinkles or creases
7 - 17
Troubleshooting
Solving print problems
Problem
The printer prints unexpectedly
or it prints garbage data.
Recommendation
„ Make sure that the printer cable is not too long. We recommend that you use a
parallel or USB cable that is no longer than 2 meters (6.5 feet).
„ Make sure that the printer cable is not damaged or broken.
„ If you are using an interface-switching device, remove it. Connect your computer
directly to your printer, and then try again.
„ Make sure that you have chosen the proper printer driver with ‘Set as Default’.
„ Make sure that the printer is not connected to the same port that is also
connected to a storage device or scanner. Take away all other devices and
connect the port only to the printer.
„ Turn off the Status Monitor in the Device Options tab in the Windows® printer
driver.
The printer cannot print full
pages of a document. An error
message MEMORY FULL is
printed out.
„ Press Go to print the remaining data in the printer memory. Cancel the print job
if you want to delete the remaining data in the printer memory. See Control panel
button on page 4-7.
„ Reduce the complexity of your document or cut the print resolution.
„ Add more memory. See Installing extra memory on page 5-3.
The printer cannot print full
pages of a document. An error
message PRINT OVERRUN is
printed out.
„ Press Go to print the remaining data in the printer memory. Cancel the print job
if you want to delete the remaining data in the printer memory. See Control panel
button on page 4-7.
„ Reduce the complexity of your document or cut the print resolution.
„ Add more memory. See Installing extra memory on page 5-3.
„ Set page protection to AUTO by using the supplied Windows ® driver or Remote
Printer Console program.
„ Change the following settings in the Windows® printer driver, and then try again.
The best combination of the settings below will vary depending on your
document:
• Graphics mode
• TrueType mode
• Use printer TrueType ® fonts
The headers or footers appear
when the document displays on
the screen but they do not show
up when it is printed.
„ Adjust the top and bottom margins of your document.
7 - 18
Troubleshooting
Network problems
For problems concerning using your printer on a Network, see the Network User’s Guide on the CD-ROM we
have supplied.
Other problems
Problem
Recommendation
The printer cannot print. The
‘There was an error writing to
LPT1: (or BRUSB) for the
printer’ error message occurs
on your PC.
„ Make sure that the printer cable is not damaged or broken.
„ If you have an interface-switching device, make sure that you chose the correct
printer.
For Macintosh® with USB
Problem
Recommendation
The printer does not appear in
Chooser (Mac OS® 9.1 to 9.2),
Print Center (Mac OS® X 10.2)
or Print Setup Utility (Mac
OS® X 10.3 or greater).
„ Make sure that the printer is turned on.
Unable to print from the
application.
„ Make sure that the supplied Macintosh ® printer driver is installed in the Hard Disk
and that it is chosen with Chooser (Mac OS® 9.1 to 9.2), Print Center (Mac OS®
X 10.2) or Print Setup Utility (Mac OS® X 10.3 or greater).
„ Make sure that the USB interface cable is connected correctly.
„ Make sure the printer driver is installed correctly.
Printing from DOS
Problem
Cannot print from the application.
Recommendation
„ Make sure that the DOS application interface settings match those of your
printer. For example, if you are using a parallel printer cable, you would set
your DOS application printer port to LPT1.
„ Check if the printer has any printer alarms.
„ Make sure that you have chosen a printer driver in your application that is
supported by your Brother printer. For information about the printers your
machine can emulate, see About emulation modes on page 3-21.
7 - 19
Troubleshooting
BR-Script 3
Problem
Recommendation
The print speed slows down.
Add optional memory. See Installing extra memory on page 5-3.
The printer cannot print EPS data.
You need the following settings to print EPS data:
a
b
c
In the Printer folder, choose the printer you use.
Press the Advanced button on the PostScript® tab.
Choose Tagged binary communication protocol in data format.
CAUTION
Not following the instructions for using the printer may cause you to be responsible for all repairs.
7 - 20
A
Appendix
Printer specifications
Engine
Model
HL-5240
Technology
Electrophotographic
Print speed
Up to 30 ppm (Letter size) 1, Up to 28 ppm (A4 size) 1
First print time
Less than 8.5 sec
Resolution
Windows® 95/98/Me,
Windows NT® 4.0 and
Windows® 2000/XP
HL-5250DN
1200 dpi 2
HQ1200
600 dpi
300 dpi
DOS
Mac OS
600 dpi
®
1200 dpi 2
HQ1200
600 dpi
300 dpi
Linux
600 dpi
300 dpi
1
From standard paper tray and optional paper tray 2
2
If you use the high quality 1200 dpi setting (1200 × 1200 dpi) the print speed will be slower.
A-1
Appendix
Controller
Model
HL-5240
Processor
266MHz
Memory
Interface
Network
Connectivity
HL-5250DN
Standard
16 MB
Option
1 DIMM slot; expandable up to 528 MB 1 DIMM slot; expandable up to 544 MB
32 MB
Standard
Hi-Speed USB 2.0 1, IEEE 1284
Parallel
Hi-Speed USB 2.0 1, IEEE 1284 Parallel,
10/100BASE-TX Ethernet
Option
10/100BASE-TX Ethernet (NC-2100p)
N/A
Protocols
TCP/IP, NetBEUI (Optional NC-2100p) TCP/IP (Standard 10/100BASE-TX
Ethernet)
Management
tool
N/A
BRAdmin Professional 2
BRAdmin Light 3
Web BRAdmin 4
Web Based Management 5
Emulation
Resident
fonts
PCL6, BR-Script 3 (PostScript® 3™), Epson FX-850, IBM ProPrinter XL
PCL
66 scalable fonts, 12 bitmap fonts, 11 bar codes 6
PostScript® 3™ 66 fonts
1
USB is not supported under Windows® 95 or Windows NT®4.0.
2
Brother original Windows® utility for printer and print server management.
3
Brother original Macintosh® utility for printer and print server management.
4
Server based management utility. Download from http://solutions.brother.com.
5
Printer and print server management through Web browser.
6
Code39, Interleaved 2 of 5, EAN-8, EAN-13, UPC-A, UPC-E, EAN-128, Codabar, FIM (US-PostNet), ISBN, Code128
A-2
Appendix
Software
Model
Printer driver
HL-5240
Windows®
HL-5250DN
PCL Driver for Windows® 95/98/Me/2000/XP 1, Windows NT® 4.0
Generic PCL Driver for Windows NT® 4.0, Windows® 2000/XP
BR-Script 3 (PPD file) for Windows® 95/98/Me/2000/XP 1, Windows NT® 4.0.
Macintosh®
Brother Laser Driver for Mac OS® 9.1 to 9.2 and Mac OS ® × 10.2.4 or greater
BR-Script 3 (PPD file) for Mac OS® 9.1 to 9.2 and Mac OS® × 10.2.4 or greater
Linux
LPR driver for Linux 2
CUPS driver for Linux 2
Utilities
Interactive Help 3
Interactive Help 3
Driver Deployment Wizard 4
1
Download the printer driver for Windows® XP Professional x64 Edition from http://solutions.brother.com.
2
Download the printer driver for Linux from http://solutions.brother.com.
3
Instructional animations for problem solving
4
The Driver Deployment Wizard automates the installation of printers in a peer-to-peer network.
Control panel
Model
HL-5240
LED
4 LEDs
Button
2 buttons
HL-5250DN
Paper handling
Model
Multi-purpose tray
50 sheets
Paper tray (Standard)
250 sheets
Lower tray (Option)
250 sheets
Paper Output 1
Face-down
150 sheets
Duplex
Manual Duplex
Yes
Automatic Duplex
N/A
Paper Input 1
1
HL-5240
HL-5250DN
Yes
Calculated with 80 g/m2 (21 lb) paper
A-3
Appendix
Media specifications
Model
Media types
Media weights
HL-5240
HL-5250DN
Multi-purpose tray
Plain paper, Bond paper, Recycled paper, Envelopes,
Labels, Transparencies 1, Thin paper, Thick paper, Thicker
paper
Paper tray
Plain paper, Bond paper, Recycled paper, Transparencies 1,
Thin paper
Lower tray unit (Option) (LT-5300)
Plain paper, Bond paper, Recycled paper, Thin paper
Automatic duplex printing
Plain paper, Recycled paper
Multi-purpose tray
60 to 161 g/m2 (16 to 43 lb)
Paper tray
60 to 105 g/m2 (16 to 28 lb)
Lower tray unit (Option) (LT-5300) 60 to 105 g/m2 (16 to 28 lb)
Media sizes
Automatic duplex printing
60 to 105 g/m2 (16 to 28 lb)
Multi-purpose tray
Width: 69.9 to 215.9 mm (2.75 to 8.5 in.) Length: 116 to
406.4 mm (4.57 to 16 in.)
Paper tray (Standard)
A4, Letter, Legal 2, B5 (ISO), Executive, A5, A6, B6 (ISO)
Lower tray unit (Option) (LT-5300)
A4, Letter, Legal 2, B5 (ISO), Executive, A5, B6 (ISO)
Automatic duplex printing
A4, Letter, Legal 2
1
Up to 10 sheets
2
Legal size paper is not available in some regions outside the USA and Canada.
Supplies
Model
Toner
HL-5240
HL-5250DN
Standard cartridge
Approx. 3,500 pages A4/Letter pages @ 5% coverage
High yield cartridge
Approx. 7,000 pages A4/Letter pages @ 5% coverage
Drum
Approx. 25,000 A4/Letter pages (1 page / job)
Dimensions / Weights
Model
HL-5240
HL-5250DN
Dimensions (W × D × H)
371 × 384 × 246 mm (14.6 × 15.1 × 9.7 in.)
Weights
Approx. 9.5 kg (20.9 lb), not including
the drum unit and toner cartridge
Approx. 10.7 kg (23.6 lb), including the
drum unit and toner cartridge
Approx. 9.8 kg (21.6 lb), not including
the drum unit and toner cartridge
Approx. 11.0 kg (24.3 lb), including the
drum unit and toner cartridge
A-4
Appendix
Other
Model
Power consumption
Noise level
Ecology
1
Sound power
HL-5240
HL-5250DN
Printing
Average 610 W at 25 ° C
(77 ° F)
Average 610 W at 25 ° C
(77 ° F)
Standby
Average 80 W at 25 ° C
(77 ° F)
Average 80 W at 25 ° C
(77 ° F)
Sleep
Average 8 W
Average 9 W
Printing
LWA = 6.4 Bell (A)
Standby
4.0 Bell (A)
Power save
Yes
Toner save 1
Yes
We do not recommend Toner Save for printing Photo or Gray Scale images.
System Requirements
Computer Platform & Operating
System Version
Processor Speed
Minimum
RAM
Recomm
ended
RAM
Available
Hard Disk
Space
Windows®
486/66 MHz
8 MB
16 MB
40 MB
NT® Workstation 4.0 1 Intel® Pentium® 75 MHz
16 MB
32 MB
50 MB
2000 Professional
Intel® Pentium® 133 MHz
64 MB
128 MB
50 MB
Me
Intel® Pentium® 150 MHz
32 MB
64 MB
50 MB
XP Home Edition
Intel® Pentium® 300 MHz
128 MB
128 MB
50 MB
AMD Opteron™
AMD Athlon™ 64
256 MB
256 MB
50 MB
32 MB
64 MB
50 MB
128 MB
160 MB
95 1, 98, 98SE
XP Professional
XP Professional x64
Edition
Apple®
2
OS® 9.1 - 9.2
®3
Macintosh
OS® X 10.2.4 or
greater
Intel® Xeon™ with Intel® EM64T
Intel® Pentium® 4 with Intel® EM64T
All base models meet minimum
requirements
1
USB is not supported under Windows® 95 or Windows NT®4.0.
2
Download the printer driver for Windows® XP Professional x64 Edition from http://solutions.brother.com.
3
Power Macintosh with an Apple original pre-installed USB port.
A-5
Appendix
Important information for choosing your paper
This section gives information to help you choose paper to use with this printer.
Note
If you use paper that is not recommended, a paper jam or misfeed may occur in the printer. See
Recommended paper on page 2-2.
Before you buy a large quantity of paper
Make sure that the paper is suitable for the printer.
Paper for plain paper copies
Paper is divided by usage, such as paper for printing and paper for copying. The usage is usually written on
the paper’s package. Check the package to see whether it is suitable for laser printers. Use paper that is
suitable for laser printers.
Basis weight
The basis weight of the paper in general use varies in different countries. We recommend that you use paper
that weighs 75 to 90 g/m2 (20 to 24 lb), although this printer is able to cope with thinner or thicker paper than
these weights.
Unit
g/m
2
Europe
USA
80 to 90
75 to 90
lb
20 to 24
Long grain and short grain
The pulp fiber of the paper is aligned during paper manufacturing. And paper can be classified into two types,
long grain and short grain.
Long grain paper’s fiber direction is parallel to the carriage direction of the paper in the printer. Short grain
paper’s fiber direction is vertical to the carriage direction of the paper in the printer. Though most plain paper
for copying is long grain, some is short grain. We recommend that you use long grain paper for this printer.
Short grain paper is too weak for the paper carriage of the printer.
Acid paper and neutralized paper
Paper can be classified as either acid paper or neutralized paper.
Though modern paper manufacture methods started with acid paper, neutralized paper is recentry taking the
place of acid paper because of environmental issues.
However, many forms of acid paper can be found in recycled paper. We recommend that you use neutralized
paper for this printer.
You can use an acid paper check pen to distinguish acid paper from neutral paper.
A-6
Appendix
Print surface
The characteristics of the face side and reverse side of a sheet of paper may vary a little.
Usually, the opening side of the ream of the paper package is the print side. Follow the indications on the
paper package. Typically, the print side is indicated by an arrow.
Moisture content
Moisture content is the amount of water left in the paper after manufacture. It is one of the important
characteristics of the paper. This can change greatly depending on the storage environment, although usually
paper contains about 5% water by weight. Because paper often absorbs water, the amount of water can
sometimes be about 10% in a high humidity environment. When the amount of water increases, the
characteristics of the paper changes greatly. The fixing of the toner may become worse. For storage of the
paper and during use, we recommend that the humidity of the surrounding environment be between 50% and
60%.
Rough estimate of basis weight
g/m2
lb
Bond
Index
60
16
64
17
75
20
90
24
105
28
120
32
135
36
161
43
90
200
53
110
A-7
Appendix
Paper size
Paper size
mm
in.
Letter
8.5 × 11 in.
Legal
8.5 × 14 in.
Executive
7.25 × 10.5 in.
A4
210 × 297 mm
A5
148 × 210 mm
A6
105 × 148 mm
Envelope Monarch
3.875 × 7.5 in.
Envelope #9
3.875 × 8.9 in.
Envelope #10
4.12 × 9.5 in.
Envelope #11
4.5 × 10.375 in.
Envelope DL
110 × 220 mm
Envelope C5
162 × 229 mm
Envelope C6
114 × 162 mm
B5 (JIS)
182 × 257 mm
B5 (ISO)
176 × 250 mm
B6
125 × 176 mm
Folio
8.5 × 13 in.
A-8
Appendix
Symbol and character sets
For the HP LaserJet, IBM Proprinter XL, and EPSON FX-850 emulation modes, you can choose the symbol
and character sets using a web browser or the Remote Printer Console software.
How to use the web browser
To use the web browser, follow the steps below.
a
Enter [http://printer’s IP address/] into your browser.
For example: [http://192.168.1.2/] (if the printer’s IP address is 192.168.1.2)
b
c
Click Printer Settings.
d
e
Click OK.
Enter a user name and a password. The default User Name is [admin] and the default Password is
[access].
Choose the HP LaserJet, IBM Proprinter XL or EPSON FX-850 tab and click Font Setup. Choose a
symbol set you want to use from the Symbol Set list box.
How to use the Remote Printer Console
To use the Remote Printer Console software, follow the steps below.
For Windows®
a
b
c
d
Put the CD-ROM into your CD-ROM drive and close the opening screen when it appears.
Open Windows ® Explore and choose the CD-ROM drive.
Double-click the RPC folder.
See the RPC_User’s_Guide.pdf for how to install and use the Remote Printer Console.
For Macintosh®
a
b
c
Put the CD-ROM into your CD-ROM drive. Double-click the HL5200 icon on the desktop.
Double-click the RPC folder.
See the RPC_User’s_Guide.pdf for how to install and use the Remote Printer Console.
A-9
Appendix
Symbol and character sets list
OCR symbol sets
When you choose the OCR-A or OCR-B font, the matching symbol set is always used.
OCR A (0O)
OCR B (1O)
HP LaserJet mode
ABICOMP Brazil / Portugal (13P)
ABICOMP International (14P)
Desktop (7J)
Greek8 (8G)
HP German (0G)
HP Spanish (1S)
ISO Latin1 (0N)
ISO Latin2 (2N)
ISO Latin5 (5N)
ISO Latin6 (6N)
ISO2 IRV (2U)
ISO4 UK (1E)
ISO5 ASCII (0U)
ISO10 Swedish (3S)
ISO11 Swedish (0S)
ISO14 JIS ASCII (0K)
ISO15 Italian (0I)
ISO16 Portuguese (4S)
ISO17 Spanish (2S)
ISO21 German (1G)
ISO25 French (0F)
ISO57 Chinese (2K)
ISO60 Norwegian1 (0D)
ISO61 Norwegian2 (1D)
ISO69 French (1F)
ISO84 Portuguese (5S)
ISO85 Spanish (6S)
ISO8859 / 7 Latin / Greek (12N)
ISO8859 / 15 Latin (9N)
ISO8859 / 15 Latin / Cyrillic (10N)
Legal (1U)
Math-8 (8M)
MC Text (12J)
MS Publishing (6J)
PC8 (10U)
PC8 Bulgarian (13R)
PC8 D/N (11U)
PC8 Greek Alternate (437G) (14G)
PC8 Latin / Greek (12G)
PC8 PC Nova (27Q)
PC8 Turkish (9T)
PC775 (26U)
PC850 Multilingual (12U)
PC851 Greece (10G)
PC852 East Europe (17U)
PC853 Latin3 (Turkish) (18U)
PC855 Cyrillic (10R)
PC857 Latin5 (Turkish) (16U)
PC858 Multilingual Euro (13U)
PC860 Portugal (20U)
PC861 Iceland (21U)
PC863 Canadian French (23U)
PC865 Nordic (25U)
PC866 Cyrillic (3R)
PC869 Greece (11G)
PC1004 (9J)
Pi Font (15U)
PS Math (5M)
PS Text (10J)
Roman8 (8U)
A - 10
Appendix
HP LaserJet mode (Continued)
Roman9 (4U)
Roman Extension (0E)
Russian-GOST (12R)
Symbol (19M)
Turkish8 (8T)
Ukrainian (14R)
Ventura Math (6M)
Ventura Intl (13J)
Ventura US (14J)
Windows 3.0 (9U)
Windows Baltic (19L)
Windows Cyrillic (9R)
Windows Greek (9G)
Windows Latin1 (19U)
Windows Latin2 (9E)
Windows Latin5 (5T)
Wingdings (579L)
IBM mode
PC8
PC8 D/N
PC8 Turkish
PC850 Multilingual
PC852 East Europe
PC860 Portugal
PC863 Canadian French
PC865 Nordic
Epson mode
Danish I
Danish II
Dutch
French I
French II
German
Italian
Norwegian
Japanese
PC8
PC8 D/N
PC8 Turkish
PC850 Multilingual
PC852 East Europe
PC860 Portugal
PC863 Canadian French
PC865 Nordic
South African
Spanish
Swedish
UK ASCII I
UK ASCII II
US ASCII
A - 11
Appendix
Quick reference for bar code control commands
The printer can print bar codes in the HP LaserJet, EPSON FX-850, and IBM Proprinter XL emulation modes.
Print bar codes or expanded characters
Code
ESC i
Dec
27 105
Hex
1B 69
Format: ESC i n ... n \
Creates bar codes or expanded characters according to the segment of parameters ‘n ... n’. For more
information about parameters, see the following Definition of Parameters. This command must end with the
‘ \ ’ code (5CH).
Definition of Parameters
This bar code command can have the following parameters in the parameter segment (n ... n). As parameters
are effective within the single command syntax ESC i n ... n \, they do not apply in the bar code commands.
If certain parameters are not given, they take the preset settings. The last parameter must be the bar code
data start (‘b’ or ‘B’) or the expanded character data start (‘l’ or ‘L’). Other parameters can be given in any
sequence. Each parameter can start with a lower-case or upper-case character, for example, ‘t0’ or ‘T0’, ‘s3’
or ‘S3’ and so one.
Bar code mode
n = ‘t0’ or ‘T0’
CODE 39 (default)
n = ‘t1’ or ‘T1’
Interleaved 2 of 5
n = ‘t3’ or ‘T3’
FIM (US-Post Net)
n = ‘t4’ or ‘T4’
Post Net (US-Post Net)
n = ‘t5’ or ‘T5’
EAN 8, EAN 13, or UPC A
n = ‘t6’ or ‘T6’
UPC E
n = ‘t9’ or ‘T9’
Codabar
n = ‘t12’ or ‘T12’
Code 128 set A
n = ‘t13’ or ‘T13’
Code 128 set B
n = ‘t14’ or ‘T14’
Code 128 set C
n = ‘t130’ or ‘T130’
ISBN (EAN)
n = ‘t131’ or ‘T131’
ISBN (UPC-E)
n = ‘t132’ or ‘T132’
EAN 128 set A
n = ‘t133’ or ‘T133’
EAN 128 set B
n = ‘t134’ or ‘T134’
EAN 128 set C
This parameter selects the bar code mode as shown above. When n is ‘t5’ or ‘T5’ the bar code mode (EAN
8, EAN 13, or UPC A) varies according to the number of characters in the data.
A - 12
Appendix
Bar Code, expanded character, line block drawing and box drawing
n = ‘s0’ or ‘S0’
3: 1 (default)
n = ‘s1’ or ‘S1’
2: 1
n = ‘s3’ or ‘S3’
2.5: 1
This parameter chooses the bar code style as above. When the EAN 8, EAN 13, UPC-A, Code 128 or EAN
128 bar code mode is chosen, this bar code style parameter is ignored.
Expanded Character
‘S’
0 = White
1 = Black
2 = Vertical stripes
3 = Horizontal stripes
4 = Cross hatch
For example ‘S’ n1 n2
n1 = Background fill pattern
n2 = Foreground fill pattern
If ‘S’ is followed by only one parameter, the parameter is a foreground fill pattern.
Line block drawing & box drawing
‘S’
1 = Black
2 = Vertical stripes
3 = Horizontal stripes
4 = Cross hatch
Bar Code
n = ‘mnnn’ or ‘Mnnn’ (nnn = 0 ~ 32767)
This parameter shows the bar code width. The unit of ‘nnn’ is a percentage.
A - 13
Appendix
Bar code human readable line ON or OFF
n = ‘r0’ or ‘R0
Human readable line OFF
n = ‘r1’ or ‘R1
Human readable line ON
Preset:
Human readable line ON
(1) ‘T5’ or ‘t5’
(2) ‘T6’ or ‘t6’
(3) ‘T130’ or ‘t130’
(4) ‘T131’ or ‘t131’
Preset:
Human readable line OFF
All others
This parameter shows whether the printer prints the human readable line below the bar code. Human
readable characters are always printed with OCR-B font of 10 pitch and all the current character style
enhancements are masked. The default setting is determined by the bar code mode selected by ‘t’ or ‘T’.
Quiet zone
n = ‘onnn’ or ‘Onnn’ (nnn = 0 ~ 32767)
Quiet zone is the space on both sides of the bar codes. Its width can be shown using the units that are set by
the ‘u’ of ‘U’ parameter. (For the description of ‘u' or ‘U' parameter, see the next section.) The default setting
of the quiet-zone width is 1 inch.
Bar code, expanded character unit, line block drawing and box drawing
n = ‘u0’ or ‘U0’
mm (preset)
n = ‘u1’ or ‘U1’
1/10
n = ‘u2’ or ‘U2’
1/100
n = ‘u3’ or ‘U3’
1/12
n = ‘u4’ or ‘U4’
1/120
n = ‘u5’ or ‘U5’
1/10 mm
n = ‘u6’ or ‘U6’
1/300
n = ‘u7’ or ‘U7’
1/720
This parameter shows the measurement units of X-axis offset, Y-axis offset, and bar code height.
Bar code, expanded character, line block drawing and box drawing offset in X-axis
n = ‘xnnn’ or ‘Xnnn’
This parameter shows the offset from the left margin in the ‘u’- or ‘U’-specified unit.
Bar code & expanded character offset in Y-axis
n = ‘ynnn’ or ‘Ynnn’
This parameter shows the downward offset from the current print position in the ‘u’- or ‘U’-specified unit.
A - 14
Appendix
Bar code, expanded character, line block drawing and box drawing height
n = ‘hnnn’, ‘Hnnn’, ‘dnnn’, or ‘Dnnn’
1 EAN13, EAN8, UPC-A, ISBN (EAN13, EAN8, UPC-A), ISBN (UPC-E): 22 mm
2 UPC-E: 18 mm
3 Others: 12 mm
Expanded characters i 2.2 mm (preset)
Line block drawing and box drawing i 1 dot
This parameter shows the height of bar codes or expanded characters as shown above. It can start with ‘h’,
‘H’, ‘d’, or ‘D’. The height of bar codes is shown in the ‘u’- or ‘U’-specified unit. The default setting of the bar
code height (12 mm, 18 mm or 22 mm) is determined by the bar code mode selected by ‘t’ or ‘T’.
Expanded character width, line block drawing and box drawing
n = ‘wnnn’ or ‘Wnnn’
Expanded character i 1.2 mm
Line block drawing and box drawing i 1 dot
This parameter shows the width of expanded characters as shown above.
Expanded character rotation
n = ‘a0’ or ‘A0’
‘Upright (preset)
n = ‘a1’ or ‘A1’
‘Rotated 90 degrees
n = ‘a2’ or ‘A2’
‘Upside down, rotated 180 degrees
n = ‘a3’ or ‘A3’
‘Rotated 270 degrees
Bar code data start
n = ‘b’ or ‘B’
Data that follows ‘b’ or ‘B’ is read in as bar code data. Bar code data must end with the ‘ \ ’ code (5CH), which
also ends this command. The acceptable bar code data is determined by the bar code mode selected by ‘t’
or ‘T’.
„ When CODE 39 is chosen with the parameter ‘t0’ or ‘T0’
Forty three characters ‘0’ to ‘9’, ‘A’ to ‘Z’, ‘-’, ‘ . ’, ‘ (space)’, ‘$’, ‘ / ’, ‘+’, and ‘%’ can be accepted as bar code
data. Other characters will cause a data error. The number of characters for bar codes is not limited. The
bar code data automatically starts and ends with an asterisk ‘ * ’ (start character and stop character). If the
received data has an asterisk ‘ * ’ at the beginning or end, the asterisk is regarded as a start character or
stop character.
„ When Interleaved 2 of 5 is selected with the parameter ‘t1’ or ‘T1’:
Ten numerical characters ‘0’ to ‘9’ can be accepted as bar code data. Other characters cause a data error.
The number of characters for bar codes is not limited. This mode of bar codes needs even characters. If
the bar code data has odd characters, ‘0’ is automatically added to the end of the bar code data.
A - 15
Appendix
„ When FIM (US-Post Net) is selected with the parameter ‘t3’ or ‘T3’
Characters ‘A’ to ‘D’ are valid and one digit of data can be printed. Upper-case and lower-case alphabet
characters can be accepted.
„ When Post Net (US-Post Net) is selected with the parameter ‘t4’ or ‘T4’
Numbers ‘0’ to ‘9' can be data and it must end with a check digit. ‘?’ can be used instead of the check digit.
„ When EAN 8, EAN 13, or UPC A is selected with the parameter ‘t5’ or ‘T5’
Ten numbers ‘0’ to ‘9’ can be accepted as bar code data. The number of characters for bar codes is limited
as follows:
EAN 8: Total 8 digits (7 digits + 1 check digit)
EAN 13: Total 13 digits (12 digits + 1 check digit)
UPC A: Total 12 digits (11 digits + 1 check digit)
A number of characters other than those stated above will cause a data error that results in the bar code
data being printed as normal print data. If the check digit is not correct, the printer decides the correct
check digit automatically so that the correct bar code data will be printed. When EAN13 is selected, adding
‘+’ and a two-digit or five-digit number after the data can create an add-on code.
„ When UPC-E is selected with the parameter ‘t6’ or ‘T6’:
The numbers ‘0’ to ‘9’ can be accepted as bar code data.
Eight digits 1 2
(standard format) The first character must be ‘0’ and the data must end with a check digit.
Total eight digits = ‘0’ plus 6 digits plus 1 check digit.
Six digits 2
The first character and the last check digit are removed from the eight digit data.
1
‘?’ can be used instead of a check digit.
2
Adding ‘+’ and two-digit or five-digit number after the data creates an add-on code.
„ When Codebar is chosen with the parameter ‘t9’ or ‘T9’
Characters ‘0’ to ‘9’, ‘-’, ‘ . ’, ‘$’, ‘/’, ‘+’, ‘ : ’ can be printed. Characters ‘A’ to ‘D’ can be printed as a startstop code, which can be upper case or lower case. If there is no start-stop code, errors will happen. A
check digit cannot be added and using ‘?’ causes errors.
„ When Code 128 Set A, Set B, or Set C is selected with the parameter ‘t12’ or ‘T12’, ‘t13’ or ‘T13’, or ‘t14’
or ‘T14’
Code 128 sets A, B and C can be individually selected. Set A shows characters Hex 00 to 5F. Set B
includes characters Hex 20 to 7F. Set C includes the pairs 00 to 99. Switching is allowed between the code
sets by sending %A, %B, or %C. FNC 1, 2, 3, and 4 are produced with %1, %2, %3, and %4. The SHIFT
code, %S, allows temporary switching (for one character only) from set A to set B and vice versa. The ‘%’
character can be encoded by sending it twice.
„ When ISBN (EAN) is selected with the parameter ‘t130’ or ‘T130’
The same rules apply as for ‘t5’ or ‘T5’.
„ When ISBN (UPC-E) is selected with the parameter ‘t131’ or ‘T131’:
The same rules apply as for ‘t6’ or ‘T6’.
A - 16
Appendix
„ When EAN 128 set A, set B or set C is selected with the parameter ‘t132’ or ‘T132’, ‘t133’ or ‘T133’ or ‘t134’
or ‘T134’
The same rules apply as for ‘t12’ or ‘T12’, ‘t13’ or ‘T13’, or ‘t14’ or ‘T14’.
Box drawing
ESC i ... E (or e)
‘E’ or ‘e’ is a terminator.
Line block drawing
ESC i ... V (or v)
‘V’ or ‘v’ is a terminator.
Expanded character data start
n = ‘l’ or ‘L’
Data that follows ‘l’ or ‘L’ is read as expanded character data (or labeling data). Expanded character data must
end with the ‘ \ ’ code (5CH), which also ends this command.
Example Program Listings
WIDTH "LPT1:",255
'CODE 39
LPRINT CHR$(27);"it0r1s0o0x00y00bCODE39?\";
'Interleaved 2 of 5
LPRINT CHR$(27);"it1r1s0o0x00y20b123456?\";
'FIM
LPRINT CHR$(27);"it3r1o0x00y40bA\";
'Post Net
LPRINT CHR$(27);"it4r1o0x00y60b1234567890?\";
'EAN-8
LPRINT CHR$(27);"it5r1o0x00y70b1234567?\";
'UPC-A
LPRINT CHR$(27);"it5r1o0x50y70b12345678901?\";
'EAN-13
LPRINT CHR$(27);"it5r1o0x100y70b123456789012?\";
'UPC-E
LPRINT CHR$(27);"it6r1o0x150y70b0123456?\";
'Codabar
LPRINT CHR$(27);"it9r1s0o0x00y100bA123456A\";
'Code 128 set A
LPRINT CHR$(27);"it12r1o0x00y120bCODE128A12345?\";
A - 17
Appendix
'Code 128 set B
LPRINT CHR$(27);"it13r1o0x00y140bCODE128B12345?\";
'Code 128 set C
LPRINT CHR$(27);"it14r1o0x00y160b";CHR$(1);CHR$(2);"?\";
'ISBN(EAN)
LPRINTCHR$(27);"it130r1o0x00y180b123456789012?+12345\";
'EAN 128 set A
LPRINT CHR$(27);"it132r1o0x00y210b1234567890?\";
LPRINT CHR$(12)
END
A - 18
B
Appendix (For Europe and Other Countries)
Brother Numbers
IMPORTANT
For technical and operational help, you must call the country where you bought the printer. Calls must be
made from within that country.
Register your product
By registering your Brother product, you will be recorded as the original owner of the product.
Your registration with Brother:
„ may serve as a confirmation of the purchase date of your product should you lose your receipt;
„ may support an insurance claim by you in the event of product loss covered by insurance; and,
„ will help us to notify you of enhancements to your product and special offers.
Please complete the Brother Warranty Registration or, for your convenience and most efficient way to register
your new product, register on-line at
http://www.brother.com/registration/
Frequently asked questions (FAQs)
The Brother Solutions Center is our one-stop resource for all your printer needs. You can download the latest
drivers, software and utilities, read FAQs and troubleshooting tips to learn how to get the most from your
Brother product.
http://solutions.brother.com
You can check here for Brother driver updates.
Customer Service
Visit http://www.brother.com for contact information on your local Brother office.
Service center locations
For service centres in Europe, contact your local Brother Office. Address and telephone contact information
for European offices can be found at http://www.brother.com by selecting your country.
Internet Addresses
Brother Global Web Site: http://www.brother.com
For Frequently Asked Questions (FAQs), Product Support and Technical Questions, and Driver Updates and Utilities:
http://solutions.brother.com
B-1
Appendix (For Europe and Other Countries)
Important information: Regulations
Radio interference (220 to 240 volt model only)
This printer follows EN55022 (CISPR Publication 22)/Class B.
Before you use this product, make sure that you use one of the following interface cables.
1 A shielded parallel interface cable with twisted-pair conductors and that it is marked IEEE 1284 compliant.
2 A USB cable.
The cable must not be more than 2 meters long.
International ENERGY STAR® Compliance Statement
The purpose of the International ENERGY STAR® Program is to promote the development and
popularization of energy-efficient office equipment.
As an ENERGY STAR® Partner, Brother Industries, Ltd. has determined that this product meets the
ENERGY STAR® guidelines for energy efficiency.
IEC 60825-1 specification (220 to 240 volt model only)
This printer is a Class 1 laser product as defined in IEC 60825-1 specifications. The label shown below is
attached in countries where it is needed.
CLASS 1 LASER PRODUCT
APPAREIL À LASER DE CLASSE 1
LASER KLASSE 1 PRODUKT
This printer has a Class 3B laser diode which produces invisible laser radiation in the laser unit. You should
not open the laser unit under any circumstances.
Caution
Use of controls or adjustments or performance of procedures other than those specified in this User’s Guide
may result in hazardous radiation exposure.
B-2
Appendix (For Europe and Other Countries)
For Finland and Sweden
LUOKAN 1 LASERLAITE
KLASS 1 LASER APPARAT
Varoitus!
Laitteen käyttäminen muulla kuin tässä käyttöohjeessa mainitulla tavalla saattaa altistaa käyttäjän
turvallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle.
Varning
Om apparaten används på annat sätt än i denna Bruksanvisning specificerats, kan användaren utsättas för
osynlig laserstrålning, som överskrider gränsen för laserklass 1.
Internal laser radiation
Maximum radiation power: 5 mW
Wave length:
770 - 810 nm
Laser class:
Class 3B
B-3
Appendix (For Europe and Other Countries)
IMPORTANT - For Your Safety
To ensure safe operation, the supplied three-pin plug must be inserted only into a standard three-pin power
outlet that is properly grounded through the standard electrical wiring.
Extension cords used with this printer must be three-pin plug type and correctly wired to provide proper
grounding. Incorrectly wired extension cords may cause personal injury and equipment damage.
The fact that the equipment operates satisfactorily does not imply that the power is grounded and that the
installation is completely safe. For your safety, if in any doubt about the effective grounding of the power, call
a qualified electrician.
This product should be connected to an AC power source within the range indicated on the rating label. DO
NOT connect it to a DC power source. If you are not sure, contact a qualified electrician.
Disconnect device
You must install this printer near a power outlet that is easily accessible. In case of an emergency, you must
disconnect the power cord from the power outlet to shut off the power completely.
Caution for LAN connection (For model HL-5250DN)
Connect this product to a LAN connection that is not subjected to overvoltages.
IT power system (For Norway only)
This product is also designed for an IT power system with phase-to-phase voltage 230V.
Wiring information (for UK)
Important
If you need to replace the plug fuse, fit a fuse that is approved by ASTA to BS1362 with the same rating as
the original fuse.
Always replace the fuse cover. Never use a plug that does not have a cover.
Warning - This printer must be earthed.
The wires in the mains lead are coloured in line with the following code:
„ Green and Yellow: Earth
„ Blue: Neutral
„ Brown: Live
If in any doubt, call a qualified electrician.
B-4
Appendix (For Europe and Other Countries)
EC Declaration of Conformity
B-5
C
Appendix (For USA and Canada)
Brother Numbers
IMPORTANT
For technical and operational help, you must call the country where you bought the printer. Calls must be
made from within that country.
Register your product
By registering your product with Brother International Corporation, you will be recorded as the original owner
of the product.
Your registration with Brother:
„ may serve as a confirmation of the purchase date of your product should you lose your receipt;
„ may support an insurance claim by you in the event of product loss covered by insurance; and,
„ will help us notify you of enhancements to your product and special offers.
Please complete the Brother Warranty Registration or, for your convenience and most efficient way to register
your new product, register on-line at
http://www.brother.com/registration/
FAQs (Frequently asked questions)
The Brother Solutions Center is our one-stop resource for all your printer needs. You can download the latest
software and utilities and read FAQs and troubleshooting tips to learn how to get the most from your Brother
product.
http://solutions.brother.com
You can check here for Brother driver updates.
C-1
Appendix (For USA and Canada)
Customer Service
In USA:
1-800-276-7746
In Canada:
1-877-BROTHER
If you have comments or suggestions, please write us at:
In USA:
Printer Customer Support
Brother International Corporation
15 Musick Irvine, CA 92618
In Canada:
Brother International Corporation (Canada), Ltd.
- Marketing Dept.
1, rue Hotel de Ville Dollard-des-Ormeaux, PQ, Canada H9B 3H6
Service center locator (USA only)
For the location of a Brother authorized service center, call 1-800-284-4357.
Service center locations (Canada only)
For the location of a Brother authorized service center, call 1-877-BROTHER
Internet Addresses
Brother Global Web Site: http://www.brother.com
For Frequently Asked Questions (FAQs), Product Support and Technical Questions, and Driver Updates and Utilities:
http://solutions.brother.com
(In USA Only) For Brother Accessories & Supplies: http://www.brothermall.com
Ordering supplies
For best quality results use only genuine Brother supplies, which are available at most Brother retailers. If you
cannot find the supplies you need and you have a Visa, MasterCard, Discover, or American Express credit
card, you can order supplies directly from Brother. (In the USA, you can visit us online for a complete selection
of the Brother accessories and supplies that are available for purchase.)
In USA:
1-888-879-3232 (voice)
1-800-947-1445 (fax)
http://www.brothermall.com
In Canada:
1-877-BROTHER (voice)
Description
Item
Toner Cartridge
TN-550 (Standard, prints approx. 3, 500 pages)
TN-580 (High Yield, prints approx. 7,000 pages)
Drum Unit
DR-520
C-2
Appendix (For USA and Canada)
Important information: Regulations
Federal Communications Commission (FCC) Declaration of Conformity
(For USA)
Responsible Party:
Brother International Corporation
100 Somerset Corporate Boulevard
P.O. Box 6911
Bridgewater, NJ 08807-0911
USA
Telephone: (908) 704-1700
declares, that the products
Product name:
Laser Printer HL-5240 and HL-5250DN
Model number:
HL-52
Product option:
Lower Tray Unit LT-5300
complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
„ Reorient or relocate the receiving antenna.
„ Increase the separation between the equipment and receiver.
„ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
„ Consult the dealer or an experienced radio/TV technician for help.
Important
A shielded interface cable should be used to ensure compliance with the limits for a Class B digital device.
Changes or modifications not expressly approved by Brother Industries, Ltd. could void the user’s authority
to operate the equipment.
C-3
Appendix (For USA and Canada)
Industry Canada Compliance Statement (For Canada)
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
International ENERGY STAR® Compliance Statement
The purpose of the International ENERGY STAR® Program is to promote the development and
popularization of energy-efficient office equipment.
As an ENERGY STAR® Partner, Brother Industries, Ltd. has determined that this product meets the
ENERGY STAR® guidelines for energy efficiency.
C-4
Appendix (For USA and Canada)
Laser Notices
Laser Safety (110 to 120 volt model only)
This printer is certified as a Class 1 laser product under the U.S. Department of Health and Human Services
(DHHS) Radiation Performance Standard according to the Radiation Control for Health and Safety Act of
1968. This means that the printer does not produce hazardous laser radiation.
Since radiation emitted inside the printer is completely confined within protective housings and external
covers, the laser beam cannot escape from the machine during any phase of user operation.
FDA Regulations (110 to 120 volt model only)
The U.S. Food and Drug Administration (FDA) has implemented regulations for laser products manufactured
on and after August 2, 1976. Compliance is mandatory for products marketed in the United States. One of
the following labels on the back of the printer indicates compliance with the FDA regulations and must be
attached to laser products marketed in the United States.
MANUFACTURED:
Brother Industries, Ltd.,
15-1 Naeshiro-cho Mizuho-ku Nagoya, 467-8561 Japan
This product complies with FDA performance standards for laser products except for deviations pursuant to Laser
Notice No.50, dated July 26, 2001.
MANUFACTURED:
Brother Corporation (Asia) Ltd. Brother Buji Nan Ling Factory
Gold Garden Ind., Nan Ling Village, Buji, Rong Gang, Shenzhen, CHINA
This product complies with FDA performance standards for laser products except for deviations pursuant to Laser
Notice No.50, dated July 26, 2001.
Caution
Use of controls, adjustments or performance of procedures other than those specified in this User’s Guide
may result in hazardous radiation exposure.
Internal laser radiation
Maximum radiation power: 5 mW
Wave length:
770 - 810 nm
Laser class:
Class 3B
C-5
Appendix (For USA and Canada)
IMPORTANT - For Your Safety
To ensure safe operation, the supplied three-pin plug must be inserted only into a standard three-pin power
outlet that is properly grounded through the standard electrical wiring.
Extension cords used with this printer must be three-pin plug type and correctly wired to provide proper
grounding. Incorrectly wired extension cords may cause personal injury and equipment damage.
The fact that the equipment operates satisfactorily does not imply that the power is grounded and that the
installation is completely safe. For your safety, if in any doubt about the effective grounding of the power, call
a qualified electrician.
This product should be connected to an AC power source within the range indicated on the rating label. DO
NOT connect it to a DC power source. If you are not sure, contact a qualified electrician.
Disconnect device
You must install this printer near a power outlet that is easily accessible. In case of an emergency, you must
disconnect the AC power cord from the AC power outlet to shut off the power completely.
Caution for LAN connection (For model HL-5250DN)
Connect this product to a LAN connection that is not subjected to overvoltages.
C-6
D
Index
A
Accessories tab ...................................................... 3-10
Advanced tab ........................................................... 3-5
Automatic duplex printing ....................................... 2-18
Automatic Emulation Selection .............................. 3-21
Automatic Interface Selection ................................ 3-22
B
Back view ................................................................. 1-3
Bar code control .....................................................A-12
Basic tab .................................................................. 3-4
Booklet printing ...................................................... 2-19
BRAdmin Light ....................................................... 3-20
BRAdmin Professional ........................................... 3-20
Brother Numbers (USA/Canada) .................... C-1, C-2
BR-Script 3 ............................................................. 7-20
BR-Script 3 mode ................................................... 3-21
BR-Script printer driver .......................................... 3-12
Buffer error ............................................................... 4-4
Emulation modes ................................................... 3-21
Envelopes .......................................................2-3, 2-11
EPSON FX-850 mode ............................................ 3-21
Error messages .................................................7-2, 7-4
F
Font full ....................................................................4-4
Fonts .............................................................. 4-10, A-2
Front view ................................................................. 1-2
H
HP LaserJet mode ................................................. 3-21
I
Incorrect paper size for DX ......................................4-4
Interface .................................................................. A-2
J
C
Job cancel ................................................................4-7
Carton contents ........................................................ 1-1
Cartridge position error ............................................ 4-3
Character sets ..........................................................A-9
Cleaning ................................................................. 6-13
Consumables ........................................................... 6-1
Control panel .................................................... 4-1, A-3
Control panel button ................................................. 4-7
Corona wire ........................................... 6-6, 6-17, 6-18
Cover open .............................................................. 4-4
L
D
Device options ......................................................... 3-7
Dimensions ..............................................................A-4
Dimm ........................................................................ 5-2
DOS ....................................................................... 7-19
Download full ........................................................... 4-4
Driver Deployment Wizard ..................................... 3-20
Drum life end soon ................................................... 4-3
Drum unit ......................................................... 6-8, A-4
Duplex disabled ....................................................... 4-4
Duplex printing ....................................................... 2-15
Dust on drum ........................................................... 4-4
LEDs ........................................................................ 4-1
Linux ........................................................................ 3-1
Lower tray unit .......................................................... 5-1
M
Macintosh® ....................................................3-15, 7-19
Maintenance parts ..................................................6-12
Manual duplex printing ...........................................2-15
Media specifications ................................................ A-4
Media type ................................................................2-1
Memory ............................................................ 5-2, A-2
Memory full ............................................................... 4-4
Multi-purpose tray ................................. 2-8, 2-11, 2-16
N
Network ..................................................................3-20
Network connectivity ............................................... A-2
Network default setting ...........................................4-11
Network Print Software .......................................... 3-20
No paper ..................................................................4-4
E
Emulation .................................................................A-2
D-1
Index
O
W
OPC drum .............................................................. 7-15
Options ..................................................................... 5-1
Web BRAdmin ........................................................ 3-20
Weights ................................................................... A-4
P
Paper ............................................................... 2-1, A-6
Paper handling .........................................................A-3
Paper jams ........................................................4-4, 7-6
Parallel interface .................................................... 3-22
Plain paper ............................................................... 2-2
Power ....................................................................... 1-4
Power supply ........................................................... 1-4
Print overrun ............................................................ 4-4
Print quality ............................................................ 7-13
Print server ............................................................... 5-5
Print test page .......................................................... 4-8
Printable area ........................................................... 2-4
Printer driver ................................. 3-4, 3-12 , 3-18, A-3
Printer settings ......................................................... 4-9
Processor .................................................................A-2
Proprinter XL mode ................................................ 3-21
R
Register your product .......................................B-1, C-1
Remote Printer Console ................................. 3-22, A-9
Reprint ..............................................................3-8, 4-7
S
Scanner window ..................................................... 6-16
Service call ............................................................... 4-5
Service centers (USA/Canada) ............................... C-2
Service centres (Europe and other countries) .........B-1
Software ................................................................. 3-20
Specifications ...........................................................A-1
Support tab ............................................................ 3-11
Symbol .....................................................................A-9
System requirements ...............................................A-5
T
Toner cartridge ................................................. 6-2, A-4
Toner life end ....................................................4-3, 6-2
Toner low ................................................................. 4-3
Too many trays ........................................................ 4-4
U
USB interface ......................................................... 3-22
Utilities .....................................................................A-3
D-2