Setup guide | Brother HL-7050 Printer User Manual

Read this “Quick Setup Guide” before using the printer.
Before you can use the printer, you must set up the hardware and install
the driver.
Setting Up
Your Printer
Step 1
Windows®
USB
Step 2
Parallel
Network
Peer-toPeer (LPR)
page 14
Peer-toPeer
(NetBIOS)
page 16
Network
Shared
Printer
page 18
USB
Network
Mac®
OS X 10.1
page 23
Mac®
OS 8.6 – 9.2
page 25
Mac®
OS X 10.1
page 26
Setup is Complete!
For
Administrator
Mac®
OS 8.6 – 9.2
page 20
Macintosh®
Network
Macintosh®
USB
USB
Windows®
Network
Windows®
Parallel
Installing the Driver
Installing the Driver
Quick Setup Guide
HL-7050 series
Setting Up Your Printer
For the latest driver and to find the best solution for your problem or question, access the Brother
Solutions Center directly from the CD-ROM/Driver or go to http://solutions.brother.com
Keep this “Quick Setup Guide” and supplied CD-ROM in a convenient place for quick and easy
reference at all times.
Version 1
Safety Precautions
To Use the Printer Safely
User’s Guide
Warning
Indicates warnings that
must be observed to
prevent possible
personal injury.
Note
Indicates cautions that
must be observed to use
the printer properly or
prevent damage to the
printer.
Hint
Indicates notes and
useful tips to remember
when using the printer.
Network
User’s Guide
Indicates reference to the
User’s Guide or Network
User’s Guide which is on
the CD-ROM we have
supplied.
Warning
There are high voltage electrodes inside the printer.
Before replacing internal parts, cleaning the printer or
clearing a paper jam, make sure you have turned OFF
the power switch and unplugged the power cord from
the power outlet.
Do not handle the plug with wet hands. Doing this might
cause an electrical shock.
After you have just used the printer, some internal parts
of the printer are extremely hot. When you open the
front cover or rear cover of the printer, never touch the
shaded parts shown in the following illustration.
To prevent injuries, at least two people should lift the
printer, holding the handles on both the right and left
sides of the printer, and the front of the printer as
shown in the illustration.
Be careful not to trip on the legs of the optional
Stabilizer unit.
Note
Do not stand on the printer or the optional stabilizer.
Inside the printer
Open the face up output tray
Table of Contents
Regulations ........................................................................................................... 2
■ Getting Started
Carton Components ............................................................................................. 4
Control Panel ........................................................................................................ 4
Supplied CD-ROM ................................................................................................. 5
Setting Up Your Printer
Step 1
1. Remove the Protective Parts .............................................................................. 6
2. Install the Drum Unit Assembly .......................................................................... 6
3. Load Paper in the Paper Tray ............................................................................. 7
4. Print a Test Page .................................................................................................. 8
5. Setting Your Language on the Control Panel ................................................... 8
Installing the Driver
Step 2
For USB Interface Cable Users ................................................................ 10
1. Installing the Driver and Connecting the Printer to Your PC
2. Setting Your Printer as the Default Printer (For Windows® 2000/XP Users Only)
For Parallel Interface Cable Users .......................................................... 12
Installing the Driver and Connecting the Printer to Your PC
For Network Interface Cable Users ......................................................... 14
■ For Brother Peer-to-Peer Network Printer Users (LPR) ................................. 14
Installing the Driver and Connecting the Printer to Your PC
■ For Brother Peer-to-Peer Network Printer Users (NetBIOS) .......................... 16
Installing the Driver, Connecting the Cable and Configuring the NetBIOS port
■ For Network Shared Printer Users ................................................................... 18
Installing the Driver, Connecting the Cable and Selecting the Appropriate Printer Queue or ‘Sharename’
For USB Interface Cable Users ................................................................ 20
■ For Mac® OS 8.6 to 9.2 Users ........................................................................... 20
■
1. Connecting the Printer to Your Macintosh & Installing the Driver
2. Setting Your Printer as the Default Printer
For Mac® OS X 10.1 Users ................................................................................ 23
Connecting the Printer to Your Macintosh & Installing the BR-Script PPD File
For Network Interface Cable Users ......................................................... 25
■ For Mac® OS 8.6 to 9.2 Users ........................................................................... 25
Connecting the Printer to Your Macintosh & Installing the BR-Script PPD File
■ For Mac® OS X 10.1 Users ................................................................................ 26
Connecting the Printer to Your Macintosh & Installing the BR-Script PPD File
■ For Administrator
Network User’s Guide Chapter Map ................................................................. 28
Setting your IP Address, Subnet Mask and Gateway
(Using the Control panel) ........................................................................................ 29
Installing the BRAdmin Professional Configuration Utility
(Windows® Users Only) .......................................................................................... 30
Print Configuration Page ................................................................................... 30
Factory Default Setting ...................................................................................... 30
■ Other Information
Shipment of the Printer ...................................................................................... 31
Options ................................................................................................................ 32
■ Troubleshooting
User’s Guide Chapter 6
1
Regulations
Federal Communications Commission (FCC) Declaration of
Conformity (For USA)
Responsible Party:
Brother International Corporation
100 Somerset Corporate Boulevard
P.O. Box 6911
Bridgewater, NJ 08807-0911
USA
Telephone: (908) 704-1700
declares, that the products
Product name:
Model number:
Product options:
Laser Printer
HL-7050 and HL-7050N
Lower Tray Unit LT-7000, Duplex Unit DX-7000,
Network Card NC-4100h, Mailbox Unit MX-7000, MX7010
complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
–
–
–
–
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Important
A shielded interface cable should be used in order to ensure compliance with
the limits for a Class B digital device.
Changes or modifications not expressly approved by Brother Industries, Ltd.
could void the user’s authority to operate the equipment.
“EC” Declaration of Conformity
Manufacture
Brother Industries Ltd.,
15-1, Naeshiro-cho, Mizuho-ku,
Nagoya 467-8561, Japan
Plant
Brother Corporation (Asia) Ltd.,
Brother Buji Nan Ling Factory,
Golden Garden Ind., Nan Ling Village,
Buji Rong Gang Shenzhen, China
Plant
Brother Industries Ltd.,
Kariya Plant,
1-5, Kitajizoyama, Noda-cho,
Kariya-shi, Aichi-ken 448-0803 Japan
Herewith declare that:
Products description:
Product Name:
Laser Printer
HL-7050, HL-7050N
are in conformity with provisions of the Directives applied: Low Voltage
Directive 73/23/EEC (as amended by 93/68/EEC) and the Electromagnetic
Compatibility Directive 89/336/EEC (as amended by 91/263/EEC and 92/
31/EEC and 93/68/EEC).
Standards applied:
Harmonized:
Safety:
EN60950: 2000
EMC:
EN55022: 1998 Class B
EN55024: 1998
EN61000-3-2: 1995 + A1: 1998 + A2: 1998
EN61000-3-3: 1995
Year in which CE marking was first affixed: 2002
Issued by:
Date:
Place:
Signature:
Brother Industries, Ltd.
28 March, 2002
Nagoya, Japan
Industry Canada Compliance Statement (For Canada)
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada.
Radio interference (220-240 volt model only)
This printer follows EN55022 (CISPR Publication 22)/Class B.
Before you use this product, make sure that you use a double-shielded
interface cable with twisted-pair conductors and that it is marked “IEEE1284
compliant”. The cable must not be more than 1.8 metres long.
Kazuhiro Dejima
Manager
Quality Audit Group
Quality Management Dept.
Information & Document Company
International ENERGY STAR® Compliance Statement
The purpose of the International ENERGY STAR® Program is to promote the
development and popularization of energy-efficient office equipments.
As an ENERGY STAR® Partner, Brother Industries, Ltd. has determined that this
product meets the ENERGY STAR® guidelines for energy efficiency.
Laser Safety (110 to 120 volt Model Only)
This printer is certified as a Class I laser product under the U.S. Department
of Health and Human Services (DHHS) Radiation Performance Standard
according to the Radiation Control for Health and Safety Act of 1968. This
means that the printer does not produce hazardous laser radiation.
Since radiation emitted inside the printer is completely confined within
protective housings and external covers, the laser beam cannot escape from
the machine during any phase of user operation.
2
FDA Regulations (110 to 120 volt Model Only)
U.S. Food and Drug Administration (FDA) has implemented regulations for
laser products manufactured on and after August 2, 1976. Compliance is
mandatory for products marketed in the United States. One of the following
labels on the back of the printer indicates compliance with the FDA
regulations and must be attached to laser products marketed in the United
States.
MANUFACTURED:
Brother Industries, Ltd.,
15-1 Naeshiro-cho Mizuho-ku Nagoya, 467-8561 Japan
This product complies with FDA radiation performance standards, 21
CFR subchapter J.
Disconnect device
You must install this printer near a power outlet that is easily accessible. In
case of an emergency, you must disconnect the power cord from the power
outlet to shut off the power completely.
Caution for batteries
Do not replace the battery. There is a danger of explosion if the battery is
incorrectly replaced. Do not disassemble, recharge or dispose of the battery
in fire. Dispose of used batteries according to local regulations.
Caution for LAN connection
Connect this product to a LAN connection that is not subjected to over
voltages.
IT power system (For Norway only)
MANUFACTURED:
Brother Corporation (Asia) Ltd. Brother Buji Nan Ling Factory
Gold Garden Ind., Nan Ling Village, Buji, Rong Gang, Shenzhen, CHINA
This product complies with FDA radiation performance standards, 21
CFR Subchapter J
☛ Caution:
Use of controls, adjustments or performance of
procedures other than those specified in this manual may
result in hazardous radiation exposure.
This product is also designed for an IT power system with phase-to-phase
voltage 230V.
Opmerking / Oplaadbare Batterij Recycle Informatie (For
Netherlands Only)
Bij dit product zijn batterijen geleverd. Wanneer deze
leeg zijn, moet u ze niet weggooien maar inleveren als
Klein Chemisch Afval.
IEC 60825 specification (220 to 240 volt model only)
This printer is a Class 1 laser product as defined in IEC 60825 specifications.
The label shown below is attached in countries where it is needed.
CLASS 1LASERP RODUCT
APPAREIL Å LASER DE CLASSE 1
LASER KLASSE 1 PRODUKT
Geräuschemission / Acoustic noise emission (for Germany
only)
Lpa < 70 dB (A) DIN 45635-19-01-KL2
Wiring information (for UK)
This printer has a Class 3B laser diode which produces invisible laser
radiation in the scanner unit. You should not open the scanner unit under any
circumstances.
☛ Caution:
Use of controls or adjustments or performance of
procedures other than those specified herein may result in
hazardous radiation exposure.
For Finland and Sweden
LUOKAN 1 LASERLAITE
KLASS 1 LASER APPARAT
☛ Varoitus!
☛ Varning
Laitteen käyttäminen muulla kuin tässä käyttöohjeessa
mainitulla tavalla saattaa altistaa käyttäjän
turvallisuusluokan 1 ylittävälle näkymättömälle
lasersäteilylle.
Om apparaten används på annat sätt än i denna
Bruksanvisning specificerats, kan användaren utsättas för
osynlig laserstrålning, som överskrider gränsen för
laserklass 1.
Internal laser radiation
Maximum radiation power: 15 mW
Wave length:
760 - 810 nm
Laser class:
Class IIIb
(Accordance with 21 CFR Part 1040.10)
Class 3B
(Accordance with IEC 60825)
IMPORTANT - For Your Safety
To ensure safe operation the supplied three-pin plug must be inserted only
into a standard three-pin power outlet that is properly grounded through the
normal household wiring.
Important
If the mains plug that is supplied with this printer is not suitable for your plug
socket, remove the plug from the mains lead and fit an appropriate three-pin
plug. If the replacement plug needs a fuse, fit the same fuse as the original.
If a moulded plug comes off the mains lead, you should destroy it because a
plug with cut wires is dangerous if it is put in a live plug socket. Do not leave
it where a child might find it!
If you need to replace the plug fuse, fit a fuse that is approved by ASTA to
BS1362 with the same rating as the original fuse.
Always replace the fuse cover. Never use a plug that does not have a cover.
Warning - This printer must be earthed.
The wires in the mains lead are coloured in line with the following code :
Green and Yellow:
Blue:
Brown:
Earth
Neutral
Live
The colours of the wires in the mains lead of this printer may not match the
coloured markings identifying the terminals in your plug.
If you need to fit a different plug, you should do the following.
Remove a bit of the outer cover of the lead, taking care not to damage the
coloured insulation of the wires inside.
Cut each of the three wires to the appropriate length. If you can, leave the
green and yellow wire longer than the others so that, if the lead is pulled out
of the plug, the green and yellow wire will be the last to disconnect.
Remove a short section of the coloured insulation to expose the wires.
Extension cords used with this printer must be three-pin plug type and
correctly wired to provide proper grounding. Incorrectly wired extension
cords may cause personal injury and equipment damage.
The wire which is coloured green and yellow must be connected to the
terminal in the plug which is marked with the letter “E” or the safety earth
symbol
, or coloured green or green and yellow.
The fact that the equipment operates satisfactorily does not imply that the
power is grounded and that the installation is completely safe. For your
safety, if in any doubt about the effective grounding of the power, call a
qualified electrician.
The wire, which is coloured blue, must be connected to the terminal, which is
marked with the letter “N” or coloured black or blue.
The wire, which is coloured brown, must be connected to the terminal, which
is marked with the letter “L” or coloured red or brown.
The outer cover of the lead must be secured inside the plug. The coloured
wires should not hang out of the plug.
3
■ Getting Started
Carton Components
Printer
2
1
3
CD-ROM
4
(including User’s Guide)
Quick Setup
Guide
Drum Unit Assembly
AC Power Cord
5
1 Control Panel
2 Extension Flap
3 Top cover
4 Multi-purpose Tray
5 Paper Tray
(including Toner Cartridge)
Carton components may differ from one country to another.
Save all packing materials and the printer carton.
■ The interface cable is not a standard accessory. Please purchase the appropriate interface cable for
the interface you intend to use (Parallel, USB or Network).
■ For Parallel use a shielded interface cable that is IEEE 1284-compliant.
Control Panel
1 Data LED : Orange
Data remains in the printer buffer.
On
Blinking Receiving or processing data.
No remaining data.
Off
2 Reprint Button
5
1
Select the Reprint menu.
Please enhance the RAMDISK size when you want
to use the Reprint functions without the optional HDD
or CompactFlash.
User’s Guide Chapter 4.
3 Job Cancel Button
2
3
4
The control panel has a
buzzer function for
visually-impaired users.
See Chapter 3 in the
User’s Guide for more
information.
Stop and cancel the printer operation in progress.
4 Go Button
Exit from the control panel menu.
Reprint setting or clear error messages.
Pause / Continue printing.
5 Menu Buttons
+
–
Set
Back
User’s Guide Chapter 3.
4
Move forward through menus.
Move backward through menus.
Select the Control Panel.
Set the selected menus and settings.
Go back one level in the menu structure.
Supplied CD-ROM
You can find a variety of information on the CD-ROM.
2
3
1
2
4
3
1
4
1 Install Software
Install the printer driver and utilities.
(Mac® OS X is not supported by Install Software)
2 Documentation
View the Printer User’s Guide and Network User’s Guide in PDF
format. (Viewer included)
3 Brother Solutions Center
The Brother Solutions Center
(http://solutions.brother.com) is your one-stop resource for all
your printer needs. Download the latest drivers and utilities for
your printers, read the FAQs and troubleshooting tips, or learn
about printer solutions.
4 Maintenance Tutorial
Instruction movie for printer maintenance.
For visually impaired users, we have prepared two HTML files
on the supplied CD-ROM: index_win.html and index_mac.html.
These files can be read by Screen Reader ‘text-to-speech’
software.
5
Step 1
1
Setting Up Your Printer
Remove the Protective
Parts
Do NOT connect the interface cable.
Connecting the Interface cable is
done when installing the driver.
2
1
Remove the protective part from the paper
exit of the printer.
Paper exit
Open the top cover of the printer.
Top cover
2
1
Install the Drum Unit
Assembly
Unpack the drum unit assembly.
Remove the protective part.
Protective part
Protective part
Drum unit
assembly
2
3
Rock it from side to side several times to
distribute the toner evenly inside the
assembly.
4
Put the drum unit assembly into the printer.
5
Close the top cover of the printer.
Open the multi-purpose tray and lower it gently.
Multi-purpose
tray
3
Remove the protective part from in the
multi-purpose tray.
Protective part
4
6
Close the multi-purpose tray.
Fan the stack of paper well to avoid paper
jams and misfeeds.
5
Load paper into the paper tray.
Check that the paper is flat in the tray and
below the maximum paper mark.
Paper tray
2
Remove the protective part from inside the
paper tray.
Windows®
USB
4
Up to here.
Windows®
Parallel
Pull the paper tray completely out of the
printer.
6
3
Put the paper tray back into the printer.
While pressing the paper guide release lever,
slide the adjusters to fit the paper size.
Check that they fit correctly into the slots.
Installing the Driver
Protective part
Macintosh®
USB
Paper guide
release
lever
Windows®
Network
1
Setting Up
Your Printer
3 Load Paper in the Paper Tray
Macintosh®
Network
Adjuster
For Legal size paper, press the
universal guide release button and pull
out the rear of the paper tray.
For
Administrator
Universal guide
release lever
Go to the next page
7
Step 1
4 Print a Test Page
1
Setting Your Language
on the Control Panel
Make sure that the printer power switch is
off.
Connect the AC power cord to the printer.
ON OFF
2
5
1
Plug the AC power cord into an AC outlet.
Turn the power switch on.
Press the + button until SETUP is
displayed.
Press the Set button.
-- MENU -SETUP
2
SETUP
LANGUAGE
ON OFF
3
After the printer has finished warming up,
the READY message appears.
Extend the tray
extension flap
Press the Set button again.
3
Press the + or – button to select your
language. Press the Set button to accept.
LANGUAGE
=ENGLISH
4
*
Press the Go button. The printer prints a
test page.
Check that the test page has printed
correctly.
Go to the next page
to install the driver.
8
Step 2
Installing the Driver
Setting Up
Your Printer
Follow the instructions on this page for your operating system and interface cable.
The screens for Windows® in this Quick Setup Guide are based on Windows® XP.
Windows®
USB
For USB Interface Cable Users ............................Go to page 10
Windows®
Parallel
For Parallel Interface Cable Users.......................Go to page 12
Windows®
Network
For Network Interface Cable Users
■ Brother Peer-to-Peer Network Printer Users (LPR) ....
Go to page 14
■ Brother Peer-to-Peer Network Printer Users (NetBIOS) ..... Go to page 16
■ Network Shared Printer Users........................................... Go to page 18
Go to page 20
Go to page 23
Macintosh®
Network
■ Mac® OS 8.6 to 9.2 Users ..............................................
■ Mac® OS X 10.1 Users.....................................................
Macintosh®
USB
For USB Interface Cable Users
For Network Interface Users
Go to page 25
Go to page 26
For
Administrator
■ Mac® OS 8.6 to 9.2 Users ..............................................
■ Mac® OS X 10.1 Users.....................................................
For Administrator .................................................Go to page 28
9
Step 2
Installing the Driver
For USB Interface Cable Users
1. Installing the Driver and Connecting the Printer to Your PC
When the “Found New Hardware Wizard”
appears on your PC, click the Cancel button.
1
2
3
10
A
C
L
E
C
N
4
Click “Printer Driver.”
5
Click the Next button.
Follow the instructions on the screen.
6
Select “Standard Installation,” and then click
the Next button.
7
Select “Local Printer with USB cable,” and
then click the Next button.
Make sure the USB interface cable is NOT
connected to the printer, and then begin
installing the driver. If you have already
connected the cable, remove it.
Insert the CD-ROM into your CD-ROM
drive. The opening screen will appear
automatically.
Follow the instructions on the screen.
Click “Install Software” icon on the Menu
screen.
Setting Up
Your Printer
When this screen appears, make sure the
printer power switch is on.
Connect the USB interface cable to your
PC, and then connect it to the printer.
Click the Next button.
2. Setting Your Printer as the
Default Printer
(For Windows® 2000/XP Users
Only)
1
Click Start and Printers and Faxes.
2
Select the Brother HL-7050 series icon.
3
From the File menu, select Set as Default
printer.
Windows®
USB
8
Installing the Driver
ON OFF
Click the Finish button.
For Windows® 98 / Me users:
The Setup is now complete.
The setup is now complete.
For Windows® 2000/XP users:
Go to “2. Setting Your Printer as the
Default Printer”.
For
Administrator
9
11
Step 2
Installing the Driver
For Parallel Interface Cable Users
Installing the Driver and Connecting the Printer to Your PC
1
Turn off the printer power switch.
4
Insert the CD-ROM into your CD-ROM
drive. The opening screen will appear
automatically.
Follow the instructions on the screen.
ON OFF
2
Connect the parallel interface cable to your
PC, and then connect it to your printer.
5
Click “Install Software” icon on the Menu
screen.
3
Turn on the printer power switch.
6
Click “Printer Driver.”
7
Click the Next button.
Follow the instructions on the screen.
ON OFF
If the “Found New Hardware Wizard”
appears on your PC, click the Cancel button.
A
C
12
C
N
L
E
0
Select the port where your printer is
connected, and then click the Next button.
9
Select “Local Printer,” and then click the
Next button.
A
Click the Finish button to restart your PC.
Setting Up
Your Printer
Select “Standard Installation,” and then click
the Next button.
For
Administrator
The Setup is now complete.
Installing the Driver
Windows®
Parallel
8
13
Step 2
Installing the Driver
For Network Interface Cable Users
For Brother Peer-to-Peer Network Printer Users
(LPR)
If you are going to connect the printer to your network, we recommended that you contact your system
administrator prior to installation.
Installing the Driver and Connecting the Printer to Your PC
1
Turn off the printer power switch.
5
Click “Install Software” icon on the Menu
screen.
6
Click “Printer Driver.”
7
Click the Next button.
Follow the instructions on the screen.
8
Select “Standard Installation,” and then click
the Next button.
ON OFF
2
Connect the network interface cable to the
printer, and then connect it to a free port on
your hub.
Hub
3
Turn on the printer power switch.
ON OFF
4
14
Insert the CD-ROM into your CD-ROM
drive. The opening screen will appear
automatically.
Follow the instructions on the screen.
Select the IP address of your printer and
LPR, and then click the Next button.
B
Click the Finish button.
Setting Up
Your Printer
A
Contact your Administrator about the
Printer’s IP Address.
For Windows NT® 4.0 and
Windows® 2000/XP users:
The Setup is now complete.
For Windows® 95 / 98 / Me users:
After your PC has restarted, setup will
be complete.
Windows®
Network
Select “Search from a list of available
printers” or enter your printer IP address.
Click the Next button.
For
Administrator
0
Select “Brother Peer-to-Peer Network
Printer,” and then click the Next button.
Installing the Driver
9
15
Step 2
Installing the Driver
For Network Interface Cable Users
For Brother Peer-to-Peer Network Printer Users
(NetBIOS)
If you are going to connect the printer to your network, we recommended that you contact your system
administrator prior to installation.
Installing the Driver, Connecting the Cable and Configuring the NetBIOS
port
1
Turn off the printer power switch.
5
Click “Install Software” icon on the Menu
screen.
6
Click “Printer Driver.”
7
Click the Next button.
Follow the instructions on the screen.
8
Select “Standard Installation,” and then click
the Next button.
ON OFF
2
Connect the network interface cable to the
printer, and then connect it to a free port on
your hub.
Hub
3
Turn on the printer power switch.
ON OFF
4
16
Insert the CD-ROM into your CD-ROM
drive. The opening screen will appear
automatically.
Follow the instructions on the screen.
Select the IP address of your printer and
NetBIOS, and then click the Next button.
B
Click the Finish button.
Setting Up
Your Printer
A
Contact your Administrator about the
Printer’s IP Address.
For Windows NT® 4.0 and
Windows® 2000/XP users:
The Setup is now complete.
Windows®
Network
Select “Search from a list of available
printers” or enter your printer IP address.
Click the Next button.
For Windows® 95 / 98 / Me users:
After your PC has restarted, setup will
be complete.
For
Administrator
0
Select “Brother Peer-to-Peer Network
Printer,” and then click the Next button.
Installing the Driver
9
17
Step 2
Installing the Driver
For Network Interface Cable Users
For Network Shared Printer Users
If you are going to connect the printer to your network, we recommended that you contact your system
administrator prior to installation.
Installing the Driver, Connecting the Cable and Selecting the Appropriate
Printer Queue or ‘Sharename’
1
Turn off the printer power switch.
5
Click “Install Software” icon on the Menu
screen.
6
Click “Printer Driver.”
7
Click the Next button.
Follow the instructions on the screen.
8
Select “Standard Installation,” and then click
the Next button.
ON OFF
2
Connect the network interface cable to the
printer, and then connect it to a free port on
your hub.
Hub
3
Turn on the printer power switch.
ON OFF
4
18
Insert the CD-ROM into your CD-ROM
drive. The opening screen will appear
automatically.
Follow the instructions on the screen.
Select the “Network Shared Printer”, and
then click the Next button.
A
Setting Up
Your Printer
9
Click the Finish button.
The setup is now complete.
For
Administrator
Contact your Administrator about the
Printer’s queue.
Windows®
Network
Select your printer’s queue, and then click
the OK button.
Installing the Driver
0
19
Step 2
Installing the Driver
For USB Interface Cable Users
For Mac® OS 8.6 to 9.2 Users
1. Connecting the Printer to Your Macintosh & Installing the Driver
1
Make sure the printer power switch is on.
5
Click the “Install Software” icon on the Menu
screen. Follow the instructions on the screen.
6
Open the Macintosh HD icon.
7
For Mac® OS 8.6 to 9.04 Users:
Open the Apple Extras folder.
Open the Apple LaserWriter Software
folder.
ON OFF
2
Connect the USB interface cable to your
Macintosh, and then connect it to the
printer.
Do not connect the USB cable to the
keyboard USB Port or a non-powered
USB Hub.
3
Insert the CD-ROM into your CD-ROM
drive.
4
Double-click the Start Here! icon.
Follow the instructions on the screen.
For Mac® OS 9.1 to 9.2 Users:
Open the Application (Mac® OS 9) folder.
Open the Utilities folder.
* The screens are based on Mac® OS 9.04.
8
20
Open the Desktop Printer Utility icon.
B
Click the Create... button.
0
Click the Change... button in PostScriptTM
Printer Description (PPD) file.
Select Brother HL-7050 series, and then
click the Select button.
C
Enter your printer name (HL-7050 series),
and then click the Save button.
D
Select Quit from the File menu.
Macintosh®
USB
Click the Change... button in USB Printer
Selection.
Select HL-7050 series, and then click the
OK button.
Continue to
the next page
For
Administrator
A
Setting Up
Your Printer
Select Printer (USB), and then click the OK
button.
Installing the Driver
9
21
Step 2
Installing the Driver
For USB Interface Cable Users
For Mac® OS 8.6 to 9.2 Users
2. Setting Your Printer as the Default Printer
1
Click the HL-7050 series icon on the
Desktop.
2
Select Set Default Printer from the Printing
menu.
The setup is now complete.
22
Setting Up
Your Printer
For USB Interface Cable Users
For Mac® OS X 10.1 Users
Connecting the Printer to Your Macintosh & Installing the BR-Script PPD File
1
Make sure the printer power switch is on.
4
Double-click the PPD_Installer.pkg icon.
Follow the instructions on the screen.
5
Open the Macintosh HD icon.
6
Open the Applications folder.
Open the Utilities folder.
7
Open the Print Center icon.
ON OFF
2
Connect the USB interface cable to your
Macintosh, and then connect it to the
printer.
Macintosh®
USB
Insert the CD-ROM into your CD-ROM
drive.
Open the Mac OS X folder.
For
Administrator
3
Installing the Driver
Do not connect the USB cable to the
keyboard USB Port or a non-powered
USB Hub.
Continue to
the next page
23
Step 2
Installing the Driver
For USB Interface Cable Users
8
Click the Add Printer... button.
9
Select USB.
0
Select HL-7050 series, and then click the
Add button.
A
Select Quit Printer Center from the Printer
Center menu.
The setup is now complete.
24
Setting Up
Your Printer
For Network Interface Cable Users
For Mac® OS 8.6 to 9.2 Users
Connecting the Printer to Your Macintosh & Installing the BR-Script PPD File
1
Turn off the printer power switch.
6
Click the “Install Software” icon on the Menu
screen. Follow the instructions on the
screen.
7
Open the Chooser from the Apple Menu.
8
Click the LaserWriter8 *1 icon, and then
select BRN_xxxxxx_P1_AT. *2
Click the Setup... button.
Close the Chooser.
ON OFF
Connect the network interface cable to the
printer, and then connect it to a free port on
your hub.
3
Turn on the printer power switch.
Macintosh®
USB
Hub
Installing the Driver
2
ON OFF
5
Double-click the Start Here! icon.
Follow the instructions on the screen.
Macintosh®
Network
Insert the CD-ROM into your CD-ROM
drive.
*1 If the Apple LaserWriter8 Driver is not
already installed on your system, you
can download it from
http://www.apple.com
*2 xxxxxx are the last six digits of the
Ethernet address.
Network User’s Guide Chapter 7.
For
Administrator
4
The setup is now complete.
25
Step 2
Installing the Driver
For Network Interface Cable Users
For Mac® OS X 10.1 Users
Connecting the Printer to Your Macintosh & Installing the BR-Script PPD File
1
Turn off the printer power switch.
5
Double-click the PPD_Installer.pkg icon.
Follow the instructions on the screen.
6
Open the Macintosh HD icon.
7
Open the Applications folder.
Open the Utilities folder.
8
Open the Print Center icon.
ON OFF
2
Connect the network interface cable to the
printer, and then connect it to a free port on
your hub.
Hub
3
Turn on the printer power switch.
ON OFF
4
26
Insert the CD-ROM into the CD-ROM drive.
Open the Mac OS X folder.
Click the Add Printer... button.
0
Select AppleTalk.
B
Setting Up
Your Printer
9
Select Quit Printer Center from the Printer
Center menu.
Select BRN_xxxxxx_P1_AT*1, and then
click the Add button.
Macintosh®
Network
*1 xxxxxx are the last six digits of the
Ethernet address.
Network User’s Guide Chapter 7.
For
Administrator
A
Installing the Driver
The setup is now complete.
27
■ For Administrator
This section is for using the printer on a Network. An administrator should setup with the
following steps.
For HL-7050 users: If you are going to connect the printer to your network, purchase the optional Network
Board (NC-4100h).
Network User’s Guide Chapter Map
Windows® 95/98/ME Peer-to-Peer
Windows NT®
Windows®
2000/XP
UNIX/Linux
®
Macintosh
OS2 Warp Server
LAN Server
28
TCP/IP
Chapter 3
Peer-to-Peer Printing
NetBIOS
Chapter 4
NetBIOS Peer-to-Peer Printing
Brother Internet Print
TCP/IP
Chapter 5
How to Configure Internet Print
Netware
IPX/SPX
Chapter 6
Novell Netware Printing
Peer-to-Peer
TCP/IP
Chapter 2
TCP/IP Printing
NetBIOS
Chapter 4
NetBIOS Peer-to-Peer Printing
DLC/LLC
Chapter 8
DLC Printing
Brother Internet Print
(NT® 4.0 only)
TCP/IP
Chapter 5
How to Configure Internet Print
Netware
IPX/SPX
Chapter 6
Novell Netware Printing
Peer-to-Peer
TCP/IP
Chapter 2
TCP/IP Printing
NetBIOS
Chapter 4
NetBIOS Peer-to-Peer Printing
(Windows® 2000 only) DLC/LLC
Chapter 8
DLC Printing
IPP
(Internet Printing Protocol)
TCP/IP
Chapter 2
TCP/IP Printing
Brother Internet Print
TCP/IP
Chapter 5
How to Configure Internet Print
Netware
IPX/SPX
Chapter 6
Novell Netware Printing
TCP/IP
Chapter 1
UNIX Printing
AppleTalk
Chapter 7
Macintosh Printing
TCP/IP
Chapter 7
Macintosh Printing
TCP/IP
Chapter 2
TCP/IP Printing
NetBIOS
Chapter 4
NetBIOS Peer-to-Peer Printing
Enter the subnet mask settings in the same
way that you entered the IP address.
An asterisk mark (*) appears on the LCD.
SUBNET MASK=
0. 0. 0.
7
8
NETWORK
TCP/IP
Press the + button until IP ADDRESS= is
displayed.
Press the Set button.
TCP/IP
IP ADDRESS=
4
GATEWAY=
0. 0.
9
0.
0*
Press the Go button to put the printer back
into its READY state.
READY
Enter the IP address of the printer using the
+ and – buttons. Press the Set button to go
to the next digit. Press the Set button to
complete the IP address.
An asterisk mark (*) appears on the LCD.
Macintosh®
Network
3
Enter the gateway settings in the same way
that you entered the IP address.
An asterisk mark (*) appears on the LCD.
IP ADDRESS=
192. 0. 0.192*
Press the + button until SUBNET MASK= is
displayed. Press the Set button.
For
Administrator
5
Windows®
Network
Press the Set button again.
Windows®
Parallel
TCP/IP
GATEWAY=
-- MENU -NETWORK
2
Press the + button until GATEWAY= is
displayed. Press the Set button.
Macintosh®
USB
Press the + button until NETWORK is
displayed.
Press the Set button.
Installing the Driver
1
0*
Windows®
USB
6
Setting Up
Your Printer
Setting your IP Address, Subnet Mask and
Gateway (Using the Control panel)
TCP/IP
SUBNET MASK=
29
Installing the BRAdmin Professional
Configuration Utility (Windows® Users Only)
The BRAdmin Professional software is designed to manage your Brother network connected
devices. For example, Brother network ready printers and Brother network ready Multifunction
devices can be managed using the BRAdmin Professional software. The BRAdmin
Professional software can also be used to manage devices from other manufacturers whose
products support the SNMP (Simple Network Management Protocol). For more information on
the BRAdmin Professional utility go to http://solutions.brother.com
1
Insert the CD-ROM into your CD-ROM
drive. The opening screen will appear
automatically.
Follow the instructions on the screen.
2
Click the “Install Software” icon on the Menu
screen.
3
Follow the instructions on the screen.
Click the “BRAdmin Professional”.
The default password for the print
server is 'access'. You can use the
BRAdmin Professional software or a
web browser to change this password.
Print Configuration
Page
To print a configuration page, use a fine ball
point pen to hold down the Network Test
Button for less than 5 seconds.
Test button
(less than 5 seconds)
30
Factory Default
Setting
If you wish to reset the print server back to its
default factory settings (resetting all
information such as the password and IP
address information), use a fine ball point
pen to hold down the Network Test Button
for more than 5 seconds.
Test button
(more than 5 seconds)
■ Other Information
Setting Up
Your Printer
Shipment of the Printer
If for any reason you must ship your Printer, carefully package the Printer to avoid any damage
during transit. It is recommended that you save and use the original packaging. The Printer
should also be adequately insured with the carrier.
3
Re-pack the printer.
Windows®
Parallel
Turn off the printer power switch, and then
unplug the AC power cord.
Remove the drum unit assembly.
Place it in the plastic bag and seal the bag
completely.
Macintosh®
USB
2
Installing the Driver
ON OFF
Windows®
Network
1
Windows®
USB
When shipping the Printer, the DRUM UNIT assembly including the TONER CARTRIDGE
must be removed from the Printer and placed in the plastic bag. Failure to remove the
unit and place it in the plastic bag during shipping will cause severe damage to the
Printer and will VOID THE WARRANTY.
Macintosh®
Network
Trademarks
For
Administrator
The Brother logo is a registered trademark of Brother Industries, Ltd.
Windows® and Windows NT® are registered trademarks of Microsoft Corporation in the U.S and other countries.
Apple Macintosh, iMac, LaserWriter, and AppleTalk are trademarks of Apple Computer, Inc
HP, HP/UX, JetDirect and JetAdmin are trademarks of Hewllet-Packard Company.
UNIX is a trademark of UNIX Systems Laboratories.
Adobe PostScript and PostScript3 are trademarks of Adobe Systems Incorporated.
Netware is a trademark of Novell, Inc.
ENERGY STAR is a U.S. registered mark.
All other brand and product names mentioned in this User’s Guide are registered
Compilation and Publication
Under the supervision of Brother Industries Ltd., this manual has been compiled and published, covering the latest product
descriptions and specifications.
The contents of this manual and the specifications of this product are subject to change without notice.
Brother reserves the right to make changes without notice in the specifications and materials contained herein and shall not be
responsible for any damages (including consequential) caused by reliance on the materials presented, including but not limited
to typographical and other errors relating to the publication.
This product is designed for use in a Professional Environment.
31
Options
The printer has the following optional accessories. You can increase the capabilities of the
printer with these items.
User’s Guide Chapter 4.
Lower Tray Unit
Stabilizer
Duplex Unit
Mailbox Unit
LT-7000
SB-4000
DX-7000
MX-7000 series
You can install up to three 500
sheet Lower tray units.
Network Board
(For HL-7050 only)
When you install 3 Lower trays The Duplex unit is an optional
device that allows you to print
units and Mailbox unit, you
on both sides of a page.
must install the optional
stabilizer.
Compact Flash Card
DIMM Memory
NC-4100h
If you are going to connect the
printer to your network,
purchase the optional Network
board.
32
HDD
HD-EX
The printer accepts a
CompactFlash card for saving
macros, print jobs, fonts and
print logs.
You can expand the memory up With the HDD installed you can
to 288 MB by installing (100-pin save macros, print jobs, fonts
and print logs.
DIMM) memory modules.
Ir-DA Interface
Font Package
Barcode Font
IR-1000
BS-3000
BT-1000
The optional font package (BS3000) is the CD-ROM you need
for installing the 136 PS3 Agfa
and TrueType Fonts.
The optional Barcode fonts
package (BT-1000) is the CDROM you need for installing the
Barcode Fonts.
The IR-1000 connects to the
parallel interface for infrared
wireless printing.
The Mailbox unit allows you to
sort or direct output to any bin.
LJ1467001 A
Printed in China
©2002 Brother Industries, Ltd. ©1998-2002 TROY XCD Inc. ©1983-1998 PACIFIC SOFTWORKS INC. ALL
RIGHTS RESERVED
Download PDF

advertising